CABLE ACCESSORIESCatalogue
www.voltex.co.za
CABL
E A
CCES
SORI
ES
INDeX
Universal Gland and Cable Rating Chart 02
Glands, Boxes and Shrouds 03
Cable Glands 10
Gland Accessories 11
Utility Junction Box 12
Glands 12
Reducers and Adaptors 13
Joint Kits 14
CTC Kits 17
Lugs and Ferrules 18
Pre-Insulated Terminals 26
Brass Terminals 32
3M Tapes 33
Nitto Insulation Tape 35
General Safety Tape 35
Cable Ties and Strapping 36
Cable Ties and Accessories 39
Cable Tie Mounts 39
Cable and Wire Markers 40
Wire Duct 42
Connectors 43
Heat Shrink 44
Putty 46
Cable Clips 46
Grommets, Plugs and Strips 47
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
2
uNIVeRSal glaND aND CaBle RatINg CHaRt
Note - Cable Construction: Plain annealed stranded copper conductors, PVC insulated, PVC Bedded, Galvanised steel wire armoured, PVC Sheathed (600/1000V). SABS 1507/1000
approximate Dimensions and NettMass per 100m Sustained Current Ratings Voltage
Drop to Suit Clampto Suit
Rated area Number of Cores
Maximum overall
DiameterNett Mass In air laid Direct In Ducts Per
m/amp Size
(mm²) (mm) (kg) (amp) (amp) (amp) (mV)
1,5
2 14,0 39 23 29 23 29
0
E26
3 14,5 4420 24 20 25
E274 15,5 49
2,5
2 15 45 31 37 31 18
3 15,5 5026 32 26 15
E28
4 16,5 580-1
4
2 17 59 41 50 41 11
3 17,5 6636 42 34 9,5
14 18,5 77
6
2 17,5 67 53 62 51 7,3
3 18,5 7845 53 43 6,4
4 20 91
2 E3010
2 21 89 72 83 68 4,4
3 22 10262 70 58 3,8
4 23,5 120
16
2 18,5 93 96 107 88 2,8
3 20,5 11482 91 75 2,4
4 23 140 3 E32
25
2 21,5 120 128 142 116 1,75 2-3 E30
3 24,5 160109 119 96 1,50
3
E324 27,5 200
35
2 23 142 156 171 139 1,25 E30
3 27,5 200133 143 116 1,10
E32
429,5
247 3-4
E34503 250
162 169 138 0,8144 34 338
703 33 344
205 210 171 0,574 39,5 470
4-5E35
953 38,5 482
252 251 205 0,43E364 45 612
5120
3 42,5 590291 285 234
0,35
4 47 752 0,34E38
1503 45 705
334 320 263 0,295-6
4 53 960
6E40
1853 52 910
383 361 298 0,254 58 1150 E42
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
3
glaNDS, BoXeS aND SHRouDS
Neoprene Shroud - Short
Size Reference Metric Size Model Product Code
0 M20 1521-0 H0000416
1 M20 152101 H0000417
2 M25 152102 H0000418
3 M32 152103 H0000419
4 M40 152104 H0000420
5 M50 152105 H0000421
6 M63 152106 H0000422
7 M75 152107 H0000423
PVC Shroud - Short
Size Reference Metric Size Model Product Code
0 M20 1522-0 H0000428
1 M20 152201 H0000429
2 M25 152202 H0000430
3 M32 152203 H0000431
4 M40 152204 H0000432
5 M50 152205 H0000433
6 M63 152206 H0000434
7 M75 152207 H0000435
8 M80 152208 H0000436
9 M90 152209 H0000437
10 M100 152210 H0000438
CCg BW Captive Cone gland tM
(for SWa and aluminum armour Cable)
gland Size Reference Model Product Code
0-20s 0503-0 H0000178
1-20 050301 H0000179
2-25 050302 H0000181
3-32 050303 H0000182
4-40 050304 H0000183
5-50 050305 H0000184
6-63 050306 H0000185
7-75 050307 H0000186
8-80 050308 H0000187
9-90 050309 H0000188
10-100 050310 H0000180
11-110 050311 -
12-120 050312 -
Features and Benefits
• For indoor use.• Two part handling, no loose parts.• Freely rotating captive cone, providing an armour clamp and earth bond without twisting the armouring.• Precision manufactured from high quality brass (nickel plated) or aluminium on request.• Complete with heavy duty locknut.
Note - Items above with (-) in the Product Code column are available on special request.
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
4
glaNDS, BoXeS aND SHRouDS
a2Compression gland
(for unarmoured Cable)
gland Size Reference Model Product Code
0-20s 0535-0 H0000197
00-20ss 053500 H0000198
1-20 053501 H0000199
2-25 053502 H0000200
3-32 053503 H0000201
4-40 053504 H0000202
5-50 053505 H0000203
6-63 053506 H0000204
7-75 053507 H0000205
8-80 053508 H0000206
9-90 053509 H0000207
*10-100 053510 H0004237
*11-110 053511 H0004238
Features and Benefits
• For indoor and outdoor use.• Seals the cable sheath to IP66/68.• Specially formulated elastomeric seals.• Precision manufactured from high quality brass (nickel plated) available in aluminium or stainless steel on request.• Complete with heavy duty locknut.• Complete with thread sealing gasket.
IPlus tM
Captive Component glandtM
(for Steel Wire armour Cable)
gland Size Reference Model Product Code
00-16ss 054600-16-IP H0004239
00-20ss 054600-IP H0004240
0-20s 0546-0-IP H0002094
1-20 054601-IP H0002095
2-25 054602-IP H0002096
3-32 054603-IP H0002097
4-40 054604-IP H0002098
5-50 054605-IP H0002099
6-63 054606-IP H0004241
7-75 054607-IP H0004242
Features and Benefits
• For highly corrosive and wet locations.• Factory fitted captive elastomeric seals for Built-in SafetyTM.• The screw-on Corrosion GuardTM is manufactured from non-corrosive material to protect the armour and metal parts of the gland.• Corrosion GuardTM screws onto the gland body and seals over the outer sheath of the cable giving an IP66/68 and deluge proof seal.• Cable Gland is precision manufactured from high quality brass (nickel plated).• Complete with sealing gasket and with heavy duty locknut.
Z
Posi-Flex tM
Compression gland tM
(for unarmoured Cable)
gland Size Reference Model Product Code
00-20ss 053800 H0000378
0-20s 0538-0 H0000377
1-20 053801 H0000379
2-25 053802 H0000380
3-32 053803 H0000381
4-40 053804 H0000382
Features and Benefits
• For use in highly corrosive areas.• Seals the cable sheath to IP66/68.• Specially formulated elastomeric seals.• Brass parts are encapsulated in a non-corrosive body.• Marine grade electroless nickel-plated entry threads.• Complete with a thread sealing gasket.
Note - Longer lead times apply to items marked with a (*) in the sizes column and need to be confirmed at the time the order is placed.
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
5
glaNDS, BoXeS aND SHRouDS
D1WCaptive Component gland tM (for Steel Wire armoured Cable)
gland Size Reference Model Product Code
00-16ss 052000-16 H0004244
00-20ss 052000 H0004245
0-20s 0520-0 H0004246
1-20 052001 H0003228
2-25 052002 H0003229
3-32 052003 H0003230
4-40 052004 H0003231
5-50 052005 H0003232
6-63 052006 H0003233
7-75 052007 H0002540
8-80 052008 H0004248
9-90 052009 H0004249
Features and Benefits
• For indoor and outdoor use when fitted with a shroud.• Two piece handling, no loose parts.• Freely rotating captive cone and inspectible cone ring, providing an armour clamp and earth bond without twisting the armour wire.• Factory fitted captive elastomeric inner seal for ingress protection IP66/68.• Seals on the inner sheath of the cable.• Precision manufactured from high quality brass (nickel plated).• Complete with thread sealing gasket and heavy duty locknut.
Note - Items above with (-) in the Product Code column are available on special request.
FlPCaptive Component glandtM (for Steel Wire armoured Cable)
“ex db I/IIC, ex eb I/IIC, ex tb IIIC, ex nR IIC”
gland SizeReference Model
Cable Details (Diameter)
Maximum length
Hexagonal Details
(Maximum) Product Code
Min - Max 'a' Max 'B' 'e' 'Flats' 'Crns'
0-20s 0521 - 0 8,0-11,5 16,0 46 25 28 H0000217
1-20 052101 11,5-14,0 19,0 48 30 34 H0000218
2-25 052102 14,0-20,5 26,5 60 42 48 H0000219
3-32 052103 20,5-26,5 33,0 76 47 54 H0000220
4-40 052104 26,5-32,5 40,5 84 60 69 H0000221
5-50s 052155 32,5-38,0 46,0 90 74 85 -
5-50 052105 38,0-44,5 52,0 90 74 85 H0000222
6-63 052106 50,0-56,0 67,0 96 85 98 H0000223
Features and Benefits
• For Group I underground mines, Group II, III, Zone 1, 2, 21 and 22 hazardous areas.• Two-part handling, freely rotating captive cone and inspectible cone ring providing an armour clamp and earth bond on the steel wire armour.• Factory fitted with a specially formulated elastomeric seal provides Built-in SafetyTM.• No loose parts that can get lost.• Precision manufactured from high-quality brass (marine grade electroless nickel plated).• Complete with a thread sealing gasket and an end cap safety gauge for correct gland selection.
FlP Hose (Compression gland for unarmoured Cable)“ex db I/IIC, ex eb I/IIC, ex tb IIIC, ex nR IIC”
gland SizeReference Model
Cable Details (Diameter)
Hexagonal Details
(Maximum) Product Code
Min - Max'a' 'Flats' 'Crns'
0-20s 0527-0 8,0-11,5 25 28 H0000241
1-20 052701 11,5-14,0 30 34 H0003094
2-25 052702 14,0-20,5 42 48 H0000242
3-32s 052703 20,0-26,5 47 54 H0002544
4-40 052704 26,5-32,5 60 69 H0002545
5-50 052705 TBA TBA TBA H0002546
Features and Benefits
• For Group I underground mines, Group II, III, Zone 1, 2, 21 and 22 hazardous areas.• Fitted complete with a specially formulated elastomeric captive seal for Built-in SafetyTM.• A hose tail provides for clamping a protective hose over the cable.• Precision manufactured from high-quality brass (marine grade electroless nickel plated) or stainless steel.• Complete with sealing gasket and an end cap safety gauge for correct gland selection.
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
6
glaNDS, BoXeS aND SHRouDS
FlP tR Compression gland (for unarmoured Cable)“ex db I/IIC, ex eb I/IIC, ex tb IIIC, ex nR IIC”
gland Size Reference Model
entry thread Cable Details Maximum length
Hexagonal Details (Maximum) Product
CodeMetric-NPt 'C' 'D' Min - Max 'a' 'e' 'Flats' 'Crns'
00-20ss 052400 M20 15 3,5-8,5 57 25 28 H0000244
0-20s 0524-0 M20 15 8,0-11,5 57 25 28 H0000243
1-20 052401 M20 15 11,5-14,0 59 30 34 H0000245
2-25 052402 M25 15 14,0-20,5 71 42 48 H0000246
3-32 052403 M32 15 20,5-26,5 87 47 54 H0000247
4-40 052404 M40 20 26,5-32,5 96 60 69 H0000248
5s-50s 052455 M50 20 32,5-38,0 112 74 85 H0010219
5-50 052405 M50 20 38,0-44,5 112 74 85 H0000249
6s-63s 052465 M63 20 44,5-50,0 124 85 98 H0010220
6-63 052406 M63 20 50,0-56,0 124 85 98 H0000250
7-75 052407 M75 TBA TBA TBA TBA TBA H0002547
Features and Benefits
• For Group I underground mines, Group II, III, Zone 1, 2, 21 and 22 hazardous areas.• No loose parts that can get lost.• Fitted with specially formulated captive elastomeric seal provides Built-in SafetyTM.• Provided with an extra gripper seal to grip the cable.• Precision manufactured from high quality brass (Marine GradeTM Electroless Nickel Plated) available in stainless steel 316/316L on request.• Complete with thread sealing gasket and an end cap safety gauge for correct gland selection.
Note - Items above with (-) in the Product Code column are available on special request.
D1eX Captive Component glandtM for Steel Wire armoured Cable“ex db IIC, ex eb IIC, ex tb IIIC, ex nR IIC”
gland Size Reference Model Product Code
00-16ss 051900-16 H0004266
00-20ss 051900 H0004267
0-20s 0519-0 H0000208
1-20 051901 H0002718
2-25 051902 H0002719
3-32 051903 H0002720
4-40 051904 -
5-50 051905 H0002542
6-63 051906 H0004268
7-75 051907 H0004269
8-80 051908 H0004270
9-90 051909 H0004271
10-100 051910 H0004272
Features and Benefits
• For indoor, Group II, III, Zone 1, 2, 21 and 22 hazardous areas.• Two part handling, no loose parts.• Freely rotating captive cone and inspectible cone ring provides an armour clamp and earth bond on steel wire armour.• Precision manufactured from high quality brass (Marine GradeTM Electroless Nickel Plated).• Specially formulated captive elastomeric seal for Built-in SafetyTM, seals on the inner sheath of the cable IP65/66/68.• Complete with thread sealing gasket.• According to IEC 60079-14, 10.6.2: This gland will only maintain Ex d integrity when used with substantially round, compact and filled cable. If not, a CCG QuickStop-Ex™ barrier gland should be used.
a2eX Compression gland for unarmoured Cable“ex db IIC, ex eb IIC, ex tb IIIC, ex nR IIC”
gland Size Reference Model Product Code
00-16ss 053600-16 H0004273
00-20ss 053600 H0000172
0-20s 0536-0 H0000171
1-20 053601 H0000173
2-25 053602 H0000174
3-32 053603 H0000175
4-40 053604 H0000176
5-50 053605 H0000177
6-63 053606 H0002721
7-75 053607 H0002722
Features and Benefits
• For indoor, outdoor, Group II, III, Zone 1, 2, 21 and 22 hazardous areas.• Inner seal seals on the cable sheath.• Outer seal grips the cable giving superior cable retention and IP rating.• Precision manufactured from high quality brass (Marine GradeTM Electroless Nickel Plated) available in stainless steel 316/316L on request.• Complete with a thread sealing gasket.
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
7
ex Corrosion guard Cable gland(for Steel and aluminium armoured Cable)“ex db IIC, ex eb IIC, ex tb IIIC, ex nR IIC”
gland Size Reference Model Product Code
00-16ss 054700-16 H0004274
00-20ss 054700 H0004275
0-20s 0547-0 H0000209
1-20 054701 H0000210
2-25 054702 H0000211
3-32 054703 H0000212
4-40 054704 H0000213
5-50 054705 H0000214
6-63 054706 H0000215
7-75 054707 H0000216
8-80 054708 H0004276
9-90 054709 H0004277
10-100 054710 H0004278
Features and Benefits
• For highly corrosive, wet locations, Group II, III, Zone 1, 2, 21 and 22 hazardous areas.• Factory fitted captive elastomeric seals for Built-in SafetyTM.• Two-part handling, freely rotating captive cone and inspectible cone ring provides an armour clamp and earth bond on steel wire and aluminium armour.• Corrosion GuardTM screws onto the gland body and seals over the outer sheath of the cable giving an IP68 and deluge proof seal protecting the armour and metal parts of the gland.• Cable Gland is precision manufactured from high-quality brass (Marine • GradeTM Electroless Nickel Plated) available in stainless steel 316/316L on request.• Complete with thread sealing gasket.• According to IEC 60079-14, 10.6.2: This gland will only maintain Ex d integrity when used with substantially round, compact and filled cable. If not, a CCG QuickStop-Ex™ barrier gland should be used.
Posi grip tM Compression gland(for unarmoured Cable)
“ex db IIC, ex eb IIC, ex tb IIIC, ex nR IIC”
gland Size Reference Model Product Code
00-20ss 054500 H0000225
0-20s 0545-0 H0000224
1-20 054501 H0000226
2-25 054502 H0000227
3-32 054503 H0000228
4-40 054504 H0000229
5-50 054505 H0000230
6-63 054506 H0000231
7-75 054507 H0000232
Features and Benefits
• For highly corrosive Group II, III, Zone 1, 2, 21 and 22 hazardous areas.• Complete with a gripper seal, deluge proof seal and elastomeric inner seal for complete explosion and ingress protection IP65/66/68.• Brass parts are encapsulated in a non-corrosive body.• Marine grade electroless nickel plated entry threads.• Complete with a thread sealing gasket.
glaNDS, BoXeS aND SHRouDS
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
8
glaNDS, BoXeS aND SHRouDS
Handi FittM 4-Way Junction Box(for general Industrial and Mining electrical Installations)
“IP66/68”
Box Reference Size Model Product Code
0-M20 0650-0 H0000058
1-M20 065001 H0000059
2-M25 065002 H0000060
3-M32 065003 H0000061
4-M40 065004 H0000091
Features and Benefits
• Handi-FitTM Box for general industrial and mining electrical installations.• Screw-on lid provides ease of installation. Lid locking with a special key prevents unauthorised tampering.• Empty boxes are not supplied with lanyard.• Raised domed lid facilitates connections to be made outside of the box.• Only approved CCG cable glands and terminals must be used.• No exposed metal parts.• Dust and water proof to IP66/68 when used with CCG sealed cable glands.• No drilling or tapping of cable entries required.• Mounting studs provided for DIN rail if using terminal blocks.• Internal earthing to all entries and rail provided.• Handi-FitTM Box can be buried for extended periods.• 4-Way and H-Boxes with parallel entries available on request.• Red Fire Rated Box for emergency circuits available (925oC for 3-hours).
Handi FittM Y Junction Box(for general Industrial and Mining electrical Installations)
“IP66/68”
Box Reference Size Model Product Code
0-M20 0651-0 H0004279
1-M20 065101 H0000055
2-M25 065102 H0002485
3-M32 065103 H0000057
Features and Benefits
• Handi-FitTM Box for general industrial and mining electrical installations.• Screw-on lid provides ease of installation. Lid locking with a special key prevents unauthorised tampering.• Empty boxes are not supplied with lanyard.• Raised domed lid facilitates connections to be made outside of the box.• Only approved CCG cable glands and terminals must be used.• No exposed metal parts.• Dust and water proof to IP66/68 when used with CCG sealed cable glands.• No drilling or tapping of cable entries required.• Mounting studs provided for DIN rail if using terminal blocks.• Internal earthing to all entries and rail provided.• Handi-FitTM Box can be buried for extended periods.• 4-Way and H-Boxes with parallel entries available on request.• Red Fire Rated Box for emergency circuits available (925oC for 3-hours).
utIlItYtM Junction Box(for general Industrial electrical Installations)
“IP66/68”
Box Reference Size Model Product Code
20mm 102101 H0000063
25mm 102102 H0000064
Features and Benefits
• Utility BoxTM for general industrial and mining electrical installations.• Screw-on lid provides ease of installation. Lid locking with a special key prevents unauthorised tampering.• Empty boxes are not supplied with lanyard.• Only approved CCG cable glands and terminals must be used.• No exposed metal parts.• Dust and waterproof to IP66/68 when used with CCG sealed cable glands.• No drilling or tapping of cable entries required.• Mounting studs provided for DIN rail if using terminal blocks.• Internal earthing to all entries and rail provided.• One box offers 1, 2, 3 or 4 way versatility (reduced stock holding).
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
9
PoSI FittM 4 Way Junction Box(for Hazardous Installations)
“ex e IIC, ex na IIC, ex t IIIC, IP66/68”
Box Reference Size Model Product Code
0-M20 1003-0 H0000046
1-M20 100301 H0000049
2-M25 100302 H0000053
3-M32 100303 H0000054
Features and Benefits
• High-temperature resistance, corrosion resistant and anti-static properties.• Raised domed lid facilitates connections to be made clear of the box base.• Screw-on lid provides ease of installation. Lid locking with a special key prevents unauthorised tampering. • Boxes with see-through polycarbonate “adapt-a-lids” available on request. • Empty boxes are not supplied with lanyard.• Only approved CCG cable glands and Ex e terminals must be used.• DIN Rail mounting studs are provided for use with terminal blocks.• Dust and watertight to IP66/68, when fitted with CCG sealed cable glands.• No drilling of the cable entries required.• Internal earthing to all entries and rail.
PoSI FittM Y Junction Box(for Hazardous Installations)
“ex e IIC, ex na IIC, ex t IIIC, IP66/68”
Box Reference Size Model Product Code
0-M20 1009-0 H0001425
1-M20 100901 H0002732
2-M25 100902 H0002483
3-M32 100903 H0002484
Features and Benefits
• High-temperature resistance, corrosion resistant and anti-static properties.• Raised domed lid facilitates connections to be made clear of the box base.• Screw-on lid provides ease of installation. Lid locking with a special key prevents unauthorised tampering.• Boxes with see-through polycarbonate “adapt-a-lids” available on request. • Empty boxes are not supplied with lanyard.• Only approved CCG cable glands and Ex e terminals must be used.• DIN Rail mounting studs are provided for use with terminal blocks.• Dust and watertight to IP66/68, when fitted with CCG sealed cable glands.• No drilling of the cable entries required.• Internal earthing to all entries and rail.
RooF Juction Box(for general Industrial electrical Installations)
“IP66/68”
Box Reference Size Model Product Code
M25 102700 H0002252
Features and Benefits
• Roof Box is mounted through corrugated iron or asbestos type roof sheeting.• Screw-on lid provides ease of installation. Lid locking with a special key prevents unauthorised tampering. • Empty boxes are not supplied with lanyard.• Boxes with see-through polycarbonate “adapt-a-lids” available on request.• Terminal connectors and integral earth connector supplied with Roof Box.• Only approved CCG cable glands and terminals must be used.• No drilling or tapping of cable entries required.• IP66/68 glands / plugs must be used in the threaded entries.• No exposed metal parts.
glaNDS, BoXeS aND SHRouDS
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
10
CaBle glaNDS
A2 COMPRESSION GLANDS
BWL LOOSE CONE GLANDS
BWR ROTARY CONE GLANDS
type Size Benefits Features Product Code
0
• Easy to install (rotary cone).• Protects armour wire.
• Rotary cone.• High quality nickel plating. • To provide clamping of the armour
wire for earth continuity and mechanical retention of the cable.
• May be used both indoors and outdoors.
• SABS 1213 approved.
H0002742
1 H0002743
2 H0002744
3 H0002745
4 H0002746
5 H0002747
6 H0002748
7 H0002749
type Size Benefits Features Product Code
0
• Easy to install (loose cone).• Protects armour wire.
• Loose cone.• High quality nickel plating.• To provide clamping of the
armour wire for earth continuity and mechanical retention of the cable.
• May be used both indoors and outdoors.
• SABS 1213 approved.
H0002734
1 H0002735
2 H0002736
3 H0002737
4 H0002738
5 H0002739
6 H0002740
7 H0002741
type Size Benefits Features Product Code
00
• Easy to install (loose cone).• Displacement seal concept
ensures effective seal to the outer sheath.
• Novel seal design accommodates wide cable range.
• High quality nickel plating.• May be used both indoors and
outdoors.• SABS 1213 approved.
H0002750
0 H0002751
1 H0002752
2 H0002753
3 H0002754
4 H0002755
5 H0002756
6 H0002757
7 H0002758
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
11
glaND aCCeSSoRIeS
EARTH TAGS
type
Slip-on earth tag
Model Slip-SizeØ a Ø B
Product Code(mm) (mm)
ET0 020
6,8
-
ET1 1 H0010229
ET2 2 25 H0010230
ET3 3 32 H0010231
ET4 4 40 H0010233
ET5 5 50
10,5
H0010234
ET6 6 63 H0010235
ET7 7 75 -
Note - Items above with (-) in the Product Code column are available on special request.
SHROUDS
typePVC Shroud Rubber Shroud
Size Model Product Code Size Model Product Code
0 SHP0 H0002763 0 SHRL0 -
1 SHP1 H0002764 1 SHLR1 H0002929
2 SHP2 H0002765 2 SHRL2 H0002930
3 SHP3 H0002766 3 SHRL3 H0002931
4 SHP4 H0002767 4 SHRL4 H0002932
5 SHP5 H0002768 5 SHRL5 H0002933
6 SHP6 H0002769 6 SHRL6 -
7 SHP7 H0002770 7 SHRL7 -
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
12
Size Colour Product Code
Gland 00/0/1
UNI: 3-in-1 White H0000960
UNI: 3-in-1 Black H0000961
UNI: 3-in-1 Push in H0001116
Gland PVC 0 White - Screw H0000263
Gland PVC 1 White - Screw H0000265
Gland PVC 2 White H0003237
glaNDSPVC GLANDS
type total Width
outside Height
Inside Height
gland Size
Inside Width Fixing Hole
Product Code
a B C D e F g H
109 75 57 M20 94 122 96 6,9 H0000045
135 85,5 69,5 M25 124 150 106 7 H0010222
Dimensions Features and Benefits
•
• Manufactured from high impact, corrosion and UV resistant material.• For use in general and industrial installations.• Allows for 1, 2, 3 and 4 way connections.• Blanking plugs, O-rings and locknuts provided.• No need for drilling and tapping.• Internal earth plate provided (no exposed metal parts).• Din rail mounting studs provided.
utIlItY JuNCtIoN BoX
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
13
Standard Reducers - Metric
type Size Metric Male thread “a” Metric Female thread “B” Product Code
RM025M020S M25M20
H0000390
RM032M020SM32
H0000393
RM032M025S M25 H0001773
RM040M020S
M40
M20 H0000396
RM040M025S M25 H0000398
RM040M032S M32 H0000400
RM050M020S
M50
M20 H0000402
RM050M025S M25 H0000404
RM050M032S M32 H0000406
RM050M040S M40 H0000408
RM063M032S
M63
M32 H0000410
RM063M040S M40 H0000412
RM063M050S M50 H0000414
Standard adaptors - Metric
type Size Metric Male thread “a” Metric Female thread “B” Product Code
AM020M025S M20 M25 H0010168
AM025M032S M25 M32 H0002477
AM032M040S M32 M40 H0010169
AM040M050S M40 M50 -
AM050M063S M50 M63 -
AM063M075S M63 M75 -
REDUCERS AND ADAPTORS
Ex REDUCERS AND ADAPTORS
ReDuCeRS aND aDaPtoRS
ex Reducers - Metric
type Size Metric Male thread “a” Metric Female thread “B” Product Code
RM025M020E M25M20
H0000391
RM032M020EM32
H0000394
RM032M025E M25 H0000395
RM040M020E
M40
M20 H0000397
RM040M025E M25 H0000399
RM040M032E M32 H0000401
RM050M020E
M50
M20 H0000403
RM050M025E M25 H0000405
RM050M032E M32 H0000407
RM050M040E M40 H0000409
RM063M032E
M63
M32 H0000411
RM063M040E M40 H0000413
RM063M050E M50 H0000415
ex adaptors - Metric
type Size Metric Male thread “a” Metric Female thread “B” Product Code
AM020M025E M20 M25 H0000037
AM025M032E M25 M32 H0002475
AM032M040E M32 M40 H0010173
AM040M050E M40 M50 H0002166
AM050M063E M50 M63 H0010174
AM063M075E M63 M75 -
Note - Items above with (-) in the Product Code column are available on special request.
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
14
SCOTCHCAST RESIN TYPE JOINTS
JoINt KItS
In-line Splices
typeMinimum Cable outer Diameter
Maximum Cable outer Diameter
Cable Conductor Size Product Code
(mm) (mm) (mm²)
Scotchcast 82 Splicing Kits
Scotchcast 82-A1 7 16 2,5-4 H0000277
Scotchcast 82-A2 14 28 6 -16 H0000278
Scotchcast 82-A3 17 40 25-35 H0000279
Scotchcast 91 Splicing Kits
Scotchcast 91-A1 8 28 4-10 H0000280
Scotchcast 91-A2 14 32 16-25 H0000281
Scotchcast 91-A3 23 39 35-50 H0000282
Scotchcast 91-A4 28 51 70 H0000283
Scotchcast 91-A4,5 30 55 95 H0000715
Scotchcast 91-A5 45 70 120-150 H0000284
Scotchcast 91-A6 48 86 185-240 H0000285
Scotchcast 6.6kV Cable Splicing Kits
92-A5 PILC Cable 16 50 H0003108
92-A5X XLPE Cable 16 50 H0010458
Scotchcast 11kV Cable Splicing Kits
Poured Resin Joints, No. 460M Polyurethane
92-A11-6 PILC Cable 16 150 H0003071
92-A11-X6 XLPE Cable 16 150 H0001724
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
15
ELECTRICAL INSULATING RESINS
JoINt KItS
Scotchcast electrical Insulating Resins
typeSize
Product Code(cm³)
4SA Epoxy Resin in Unipak Bag A/90 H0002810
4SA Epoxy Resin in Unipak Bag B/209 H0000276
4SA Epoxy Resin in Unipak Bag C/418 H0003189
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
16
MEDIUM VOLTAGE COLDSHRINK SPLICING KITS UP TO 11kV
3 Core 11kV Cold Shrink Splicing Kits
typeCable Size
Kit Reference Product Code(mm2)
PILC 16-35 PILC Screened Splice, MVPS1 -
PILC 50-120 PILC Screened Splice, MVPS2 H0003054
PILC 150-300 PILC Screened Splice, MVPS3 -
XLPE 16-35 XLPE Splice, MVX1 - FR H0000028
XLPE 50-120 XLPE Splice, MVX2 - FR H0002651
XLPE 150-300 XLPE Splice, MVX3 - FR H0000030
3 Core 11kV Cold Shrink Splicing Kits
typeCable Size Indoor
(450, 750mm tails)outdoor
(750, 1200, 1600mm tails)
(mm2) Kit Reference Product Code Kit Reference Product Code
PILC 25-50 1001 LC-B H0001723 1001 HC-B H0002643
PILC 70-120 1002 LC-B H0003073 1002 HC-B H0003072
PILC 150-185 1003 LC-B H0002685 1003 HC-B -
XLPE 240-300 1004 LC-B - 1004 HC-B -
JoINt KItSFLAME RETARDANT SPLICING KITS
low tension Splicing Kits with Flame Retardant Mould and Flame Retardant Non Halogenated Clear epoxy Resin No. 52FR
type Size Product Code
91-A1/W(8mm-28mm)
H00031024-10mm²
91-A2/W(14mm-32mm)
H000310316-25mm²
91-A3/W(23mm-39mm)
H000310435-50mm²
91-A4/W(28mm-52mm)
H000310670mm²
91-A4,5/W(30mm-55mm)
H000310595mm²
91-A5/W(45mm-70mm)
H0010427120-150mm²
91-A5/WE with Earthing Kit(45mm-70mm)
H001042812-150mm²
91-A6/W(48mm-79mm)
H0010429185-240mm²
Note - Items above with (-) in the Product Code column are available on special request.
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
17
LOW VOLTAGE CABLE JOINT
Information:Epoxy resinsIEC / SANS approved
DURACAST RESIN CABLE JOINT KITS
CABLE TAPE SPLICING KITS
CtC KItS
Note - Items above with (-) in the Product Code column are available on special request.
typeSize
Product Code(mm²)
Dura Joint P0 - S 1,5-4 x 4C H0000268
Dura Joint P1 - S 4,0-10 x 4C H0000269
Dura Joint P2,5 - S 16-35 H0000270
Dura Joint P2 - S 10-16 x 4C H0000271
Dura Joint P3 - S 35-50 H0000273
Dura Joint P3,5 - S 50-95 H0000272
Dura Joint P4 - S 95-150 H0000274
Dura Joint P5 - S 150 - 240 H0000275
Colliery trailing Cable Coldshrink Splicing Kits up to 1.1kV
typeSize
Product Code(mm²)
CTC 6 20 - 33 H0003066
CTC 7 25 - 39 H0010430
CTC 8 30 - 49 H0001725
CTC 9 35 - 59 H0001439
typeSize
Product Code(mm²)
GPJ0 1,5-4 H0000287
GPJ1 4,0-10 H0000288
GPJ2 10-16 H0000298
GPJ2H 16-35 H0000290
GPJ3 35-50 H0000291
GPJ3H 50-95 H0000292
GPJ4 95-150 H0000293
GPJ5 150-240 H0000294
GPJ6 240-300 -
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
18
lugS aND FeRRuleSCOPPER LUGS FOR STRANDED CONDUCTOR CABLE
Dimension1. The nominal area of the circular stranded
conductor is that of the nominal lug or ferrule size.2. For flexible cables the next highest lug or
ferrule size in relation to the area must be used.3. For compacted cable the heavy duty lugs and
ferrules must be used.
Certain compacted cables vary in nominal diameter and cable diameter must be matched to the lug or ferrule barrel inside diameter.
B a
C D
F
e
Note - Items above with (-) in the Product Code column are available on special request. - Indent compression recommended for flexible stranded. - Confirm stock and brand availability with your local branch. - Components are tested to IEC 61238-1.
Nominal lug Size
typical Conductors
Stud Size
Nominal Dimensions Product Code
Circular Stranded
Flexible Stranded
(mm)
Barrel Spade
(mm2) (mm²) (mm2) (mm)a B C D e F
Inner Diameter
outer Diameter length length Hole
Position Width
1,5 3/0,81 1
3
1,9 3,8 7,0
9,04,5 7,0
H0010283 H0000964 -
412,0
H0010284 H0000966 H0002551
5 8,0 H0010285 H0000967 H0002552
6 13,0 5,5 9,0 H0010286 H0000968 H0002553
2,5 3/1,04 1,5
3
2,4 3,9 7,3
8,5
4,57,0
H0010287 H0000969 -
412,0
H0010288 H0000971 H0002554
5 9,0 H0010289 H0000972 H0002555
6 13,0 5,5 9,5 H0010290 H0000973 H0002556
8 15,0 7,5 12,0 H0010291 H0000975 H0002557
4 7/0,86 2,5
3
2,8 4,7
8,0
9,0
4,57,0
H0010292 H0000976 -
412,0
H0010293 H0000977 H0002559
5 8,5 H0010294 H0000978 H0002560
6
11,0
13,0 5,5 10,0 H0010295 H0000979 H0002561
8 17,0 6,5 13,0 H0010296 H0000980 H0002562
10 19,0 7,5 14,0 H0010297 H0000981 H0002563
6 7/1,05 4
4
3,4 5,3
11,0 12,0 4,57,5 H0010298 H0002857 H0002564
5 8,5 H0010299 H0000982 H0002565
6 8,5 13,0 5,5 9,5 H0010300 H0000983 H0002566
8 9,3 17,0 7,0 13,0 H0010301 H0000984 H0002567
10 11,0 19,0 7,5 15,0 H0010302 H0000985 -
10 7/1,36 6
5
4,4 6,3
10,512,0 4,5 9,0 H0010303 H0000987 H0002568
6 13,0 6,0 10,0 H0010304 H0000988 H0002569
811,0
17,07,5
13,0 H0010305 H0000989 H0002570
10 19,0 15,0 H0010306 H0000990 H0002571
12 12,0 20,0 10,0 19,0 H0010307 H0000991 H0002572
16 7/1,72 10
5
5,5 7,6 12,0
13,0 5,510,5 H0010308 H0000993 H0002574
6 11,0 H0010309 H0000994 H0002575
8 18,07,5
13,0 H0010310 H0000995 H0002576
10 20,0 15,0 H0010311 H0000996 H0002577
12 25,0 10,5 18,0 H0010312 H0000997 H0002578
16 27,0 13,0 24,0 H0010313 H0000998 H0002579
25
18/1,35
16
6
6,9 9,0 15,0
16,0 6,014,0
H0010314 H0000999 H0002581
8 17,08,0
H0010315 H0001000 H0002582
19/1,55
10 18,0 16,0 H0010316 H0001001 H0002583
12 21,0 11,0 18,0 H0010475 H0001002 H0002584
16 27,0 13,0 24,0 H0010317 H0000338 -
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
19
Nominal lug Size
typical Conductors
Stud Size
Nominal Dimensions Product Code
Circular Stranded
Flexible Stranded
(mm)
Barrel Spade
(mm2) (mm2) (mm2) (mm)
a B C D e F
Inner Diameter
outer Diameter length length Hole
Position Width
35
18/1,59
25
6
8,2 10,715,0
18,0
8,0
16,0
H0010318 H0001003 H0002585
89,0
H0010319 H0001004 H0002586
19/1,55
10 H0010320 H0001005 H0002587
12 22,0 10,0 18,0 - H0001006 H0002588
16 16,0 30,0 13,0 24,0 H0010321 H0001007 H0002589
50 18/1,919/1,85 35
6
10,0 12,8
16,0 17,08,0
18,0H0010322 H0001008 H0002590
8 9,0 H0010323 H0001009 H0002591
10 17,024,0 10,0 20,0
H0010324 H0001010 H0002592
12
18,0
- H0001012 H0002593
1630,0 13,0 26,0
H0010325 H0001013 H0002594
20 H0010326 H0003266 -
70 18/2,2519/2,19 50
8
11,7 15,0
20,5 20,0 9,5 21,0 H0010327 H0001014 H0002597
1021,0
26,0 11,022,0
H0010328 H0001015 H0002598
12 28,0 12,0 H0010329 H0001017 H0002599
1622,0
32,0 14,0 28,0 - H0001018 H0001342
20 34,0 15,0 30,0 H0010330 H0001175 H0002600
95 36/1,8637/1,83 70
8
13,5 17,4 23,0
24,0 9,5 25,0 H0010331 H0001019 H0002601
10 26,013,0 26,0
H0010332 H0001020 H0002602
12 28,0 H0010333 H0001022 H0002603
16 32,0 14,0 28,0 - H0001023 H0002604
20 36,0 16,0 30,0 H0010334 H0001176 H0002605
120
36/2,08
70/95
10
15,5 19,8 26,0
26,012,0
27,0 H0010335 H0001024 H0002606
12 28,0 28,0 H0010336 H0001025 H0002607
37/2,0516 32,0 14,0 30,0 H0010337 H0001026 H0002608
20 36,0 16,0 32,0 H0010338 H0002861 -
150
36/2,34
95/120
10
17,0 22,0 27,0
31,0 12,5 31,0 H0010339 H0001027 H0002609
12 33,0
16,0 32,0
H0010340 H0001028 H0002610
37/2,2916 35,0 H0010341 H0001029 H0001343
20 36,0 H0010342 H0001030 H0002661
185
36/2,59
120/150
10
19,0 24,4 29,0
29,0 12,534,0
H0010343 H0001031 H0002611
12 31,0
16,0
H0010344 H0001032 H0002612
37/2,5316
34,0 36,0H0010345 H0001033 H0002613
20 H0010346 H0001179 -
240
60/2,23
150/185
10
21,5 27,7 33,0
36,0 16,0
40,0
H0010347 H0001180 H0002614
12 H0010348 H0001034 H0002615
61/2,2616 38,0
20,0H0010349 H0001884 H0002616
20 42,0 H0010350 H0003267 H0002617
300 60/2,5561/2,53 185/240
10
24,5 31,3 35,0
35,015,0
45,0
H0010351 H0003268 -
12 H0010352 H0001886 H0002618
1645,0
H0010353 H0000367 -
20 16,0 H0010354 H0002863 H0002619
400 91/2,39 240/300
16
27,5 35,6 41,0 47,0
24,0
49,0-
- -
51,0 - -
500 91/2,67 300/400 31,6 40,0 41,5 54,0 58,0 H0000369 - -
630 127/2,54 400/500 34,5 44,6 53,0 65,0 64,0 H0000370 H0004283 -
800 127/2,87630 44,0
51,2 68,075,0
73,0 - - -
1000 127/3,22 56,6 75,0 81,0 - - -
Note - Items above with (-) in the Product Code column are available on special request. - Indent compression recommended for flexible stranded. - Confirm stock and brand availability with your local branch. - Components are tested to IEC 61238-1.
lugS aND FeRRuleS
COPPER LUGS FOR STRANDED CONDUCTOR CABLE
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
20
lugS aND FeRRuleSHEAVY DUTY COPPER LUGS FOR COMPACTED XLPE CABLE 6.35 - 11kV
Nominal lug Size SaNS
1411-1Nominal Diameter
over Conductor
Stud Size
Nominal Dimensions
Product Code
(mm)
Barrel Spade
(mm2) (mm)
a B C D e F
Inner Diameter outer Diameter length length Hole Position Width
35 7,0
10
7,30 10,50 16,024,0 11,0 19,0
H0004130
50 8,2 8,75 12,30 20,0 H0004131
70 9,7 10,40 14,60 21,0 27,0
14,0
20,0 H0004132
95 11,4 12,10 17,00 24,028,0
24,0 H0004133
120 12,6
12
14,00 19,10 26,0 26,0 H0004134
150 14,6 15,25 21,30 31,0 37,0 18,0 30,0 -
185 15,9 17,00 23,7034,0
40,019,0
33,0 H0004136
240 16,3 20,00 27,10 41,0 37,0 -
300 20,8
*
21,63 30,50 38,0 48,0 20,0 42,5 -
400 23,6 24,50 34,6451,0
49,0 23,5 48,0 -
500 26,2 28,50 38,90 52,0 25,0 54,0 -
630 30,3 33,00 45,00 53,0 65,0 28,0 64,0 H0004141
B a
C D
F
eR1
Note - Items above with (-) in the Product Code column are available on special request. - Stud sizes can be made to customer requirements. - Components are tested to IEC 61238-1.
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
21
lugS aND FeRRuleSALUMINIUM STRANDED CIRCULAR CABLE LUGS
Note - Items above with (-) in the Product Code column are available on special request. - Components are tested to IEC 61238-1.
Cable Size Stud SIzea B C D e
Palm Width Palm thickH W Product
Code(mm2) (mm) F g
25
8
65,00 28,00
8,40
17,00
12,00
15,00 4,007,00 11,30
-
10 10,40 H0004159
12 12,50 21,00 3,00 H0004160
35
8
70,00
30,00
8,4017,50 4,00
8,30 12,90
-
10 10,40 H0004162
12 12,50 21,00 3,50 H0004163
50
10
32,00
10,4020,00 4,50
9,90 14,70
H0004164
12 12,50 H0004165
16 16,50 26,00 3,50 -
70
10
78,00 36,00
10,4023,00 5,00
11,70 17,00
-
12 12,50 H0004168
16 16,50 26,00 4,50 -
95
10
85,00 39,00
10,40
18,00 27,50 5,50 13,70 19,70
H0004170
12 12,50 H0004171
16 16,50 -
120
10
89,00 45,00
10,40
17,00 31,00 6,50 15,30 22,20
H0004173
12 12,50 H0004174
16 16,50 -
150
12
100,00 48,00
12,50
20,00 16,00
34,50 7,00 17,20 24,70
H0004176
16 16,50 -
20 20,50 -
185
12
108,00 53,00
12,50
38,00 7,50 19,00 27,30
H0004179
16 16,50 -
20 20,50 -
240On request
118,00 57,00On request
22,00 18,00 43,50 8,50 21,80 31,00 H0004182
300 132,00 62,00 25,00 20,00 49,00 9,50 24,90 35,00 H0004183
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
22
Note - Components are tested to IEC 61238-1.
lugS aND FeRRuleS
ALUMINIUM 3 CORE SECTOR SHAPED CABLE LUGS
Cable Size Stud SIzea B C D e
Palm Width Palm thickH W Product
Code(mm2) (mm) F g
25
8
65,00 28,00
8,40
17,00
12,00
15,00 4,005,20 8,73
H0004184
10 10,40 H0004185
12 12,50 21,00 3,00 H0004186
35
8
70,00
30,00
8,4017,50 4,5
5,90 10,05
H0004187
10 10,40 H0004188
12 12,50 21,00 3,50 H0004189
50
10
32,00
10,4022,00 4,50
7,25 11,85
H0004190
12 12,50 H0004191
16 16,50 26,00 3,50 H0004192
70
10
78,00 36,00
10,4024,00 5,00
8,5 14,10
H0004193
12 12,50 H0004194
16 16,50 26,00 4,50 H0004195
95
10
82,00 38,00
10,40
18,00 28,00 6,00 9,55 16,35
H0004196
12 12,50 H0004197
16 16,50 H0004198
120
10
88,00 45,00
10,40
17,00 31,00 6,50 11,05 18,50
H0004199
12 12,50 H0004200
16 16,50 H0004201
150
12
103,00 48,00
12,50
20,00
18,00
34,00 7,00 12,15 20,60
H0004202
16 16,50 H0004203
20 20,50 H0004204
185
12
106,00 53,00
12,50
22,0038,00 8,50 13,40 22,48
H0004205
16 16,50 H0004206
20 20,50 H0004207
240On request
118,00 57,00 On request
43,50 8,50 15,55 26,05 H0004208
300 132,00 62,00 25,00 20,00 49,00 10,00 17,35 29,00 H0004209
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
23
Note - Items above with (-) in the Product Code column are available on special request. - Components are tested to IEC 61238-1.
lugS aND FeRRuleSALUMINIUM 4 CORE SECTOR SHAPED CABLE LUGS
Cable Size Stud SIzea B C D e
Palm Width Palm thickH W Product
Code(mm2) (mm) F g
25
8
65,00 25,00
8,40
17,00
12,00
15,00 4,005,80 7,88
-
10 10,40 H0004211
12 12,50 21,00 3,00 -
35
8
70,00
30,00
8,4017,50 4,5
7,10 9,70
-
10 10,40 H0004214
12 12,50 21,00 3,50 -
50
10
32,00
10,4020,00 4,50
8,35 10,95
H0004216
12 12,50 H0004217
16 16,50 26,00 3,00 -
70
10
78,00 36,00
10,4023,00 5,00
9,30 13,00
H0004219
12 12,50 H0004220
16 16,50 26,00 4,50 -
95
10
85,00 39,00
10,40
18,00 27,50 5,70 10,85 15,10
H0000353
12 12,50 H0001021
16 16,50 -
120
10
89,00 45,00
10,40
17,00 31,00 6,50 12,05 17,00
H0004223
12 12,50 H0004224
16 16,50 -
150
12
100,00 48,00
12,50
20,00 16,00
34,50 7,20 13,80 18,80
H0004226
16 16,50 -
20 20,50 -
185
12
108,00 53,00
12,50
38,50 8,00 15,25 21,00
H0000363
16 16,50 -
20 20,50 -
240On request
118,00 57,00On request
22,00 18,00 43,50 8,50 17,35 23,80 H0004231
300 132,00 62,00 25,00 20,00 49,00 9,70 19,50 26,40 -
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
24
lugS aND FeRRuleS
HEAVY DUTY COPPER FERRULES FOR COMPACTED XLPE CABLE 6.35 - 11kV
COPPER FERRULES FOR STRANDED CONDUCTOR CABLE
Nominal Sleeve Size
Nominal Dimensionstypical
Conductors Circular Stranded
Product Code
(mm)
Inner Diameter outer Diameter length
(mm2) a B C (mm)
1,5 1,9 3,6 13,0 3/0,81 H0010367 H0000121 H0002514
2,5 2,4 3,9 14,0 3/1,04 H0010368 H0000124 H0002515
4 2,8 4,7 16,0 7/0,86 H0010369 H0000126 H0002516
6 3,4 5,3 18,0 7/1,05 H0010370 H0000129 H0002517
10 4,4 6,3 20,0 7/1,36 H0010371 H0000131 H0002518
16 5,5 7,6 22,0 7/1,72 H0010372 H0000133 H0002519
25 6,9 9,0 25,0 18/1,35 H0002174 H0000137 H0002520
35 8,2 10,7 28,0 18/1,59 H0002175 H0000141 H0002521
50 10,0 12,8 31,0 18/1,90 H0002176 H0000144 H0002522
70 11,7 15,0 35,0 18/2,25 H0000023 H0000147 H0002523
95 13,5 17,4 39,0 36/1,86 H0002928 H0000151 H0002524
120 15,5 19,8 43,0 36/2,08 H0002177 H0000155 H0002525
150 17,0 22,0 48,0 36/2,34 H0002178 H0000159 H0002526
185 19,0 24,4 54,0 36/2,59 H0010373 H0000162 H0002527
240 21,5 27,7 60,0 60/2,23 H0010374 H0000165 H0002528
300 24,5 31,3 67,0 60/2,55 H0010375 H0000167 H0002529
400 27,5 35,6 80,0 91/2,39 H0010376 H0003265 -
500 31,6 40,0 90,0 91/2,67 - - -
630 34,5 44,6 110,0 127/2,54 - - -
800 40,0 51,2 130,0 127/2,87 - - -
1000 44,0 56,6 154,0 127/3,22 - - -
Nominal Ferrule Size
Nominal Dimensions
Product Code(mm)
Inner Diameter outer Diameter length
(mm2) a B C
35 7,30 10,5 38 H0004142
50 8,75 12,3 42 H0004143
70 10,40 14,6 43 H0004144
95 12,10 17,0 45 H0004145
120 14,00 19,1 55 H0004146
150 15,25 21,3 58 H0004147
185 17,00 23,7 64 H0004148
240 20,00 27,1 70 H0004149
300 21,63 30,5 75 -
400 24,50 34,6 80 -
500 28,50 38,9 90 -
630 33,00 45,0 100 H0004153
C
aB
Note - Items above with (-) in the Product Code column are available on special request. - Components are tested to IEC 61238-1.
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
25
Insulated Bootlace Ferrules twin
Cable SizeColour Items Per Bag Product
Code(mm2)
0,5 White
500
O0012972
0,75 grey O0012776
1 Yellow O0012978
1,5 Black O0012966
2,5 Blue 250 O0012967
4 grey
100
O0012971
6 Yellow O0012970
10 Red O0012969
lugS aND FeRRuleSALUMINIUM FERRULES
Cable Size aStranded 3 Core 4 Core
D1 D2 Product Code H W Product
Code H W Product Code(mm2) (mm)
25 66 7,00 11,30 H0000135 5,20 8,73 H0004286 5,8 7,88 -
35 70 8,30 12,90 H0000139 10,05 5,90 H0004287 7,10 9,70 -
50 74 9,90 14,70 H0000142 11,85 7,25 H0004288 8,35 10,95 H0004298
70 78 11,70 17,00 H0000145 14,10 8,25 H0004289 9,30 13,00 H0004299
95 84 13,70 19,70 H0000149 16,35 9,55 H0004290 10,85 15,10 -
120 91 15,30 22,20 H0000153 18,50 11,05 H0004291 12,50 17,00 H0004301
150 102 17,20 24,70 H0000157 20,60 12,15 H0004292 13,80 18,80 H0004302
185 108 19,00 27,30 H0000160 22,40 13,40 H0004293 15,25 21,00 -
240 118 21,80 31,00 H0000163 26,05 15,55 H0004294 17,35 23,80 H0004304
300 130 24,90 35,00 H0004233 29,00 17,35 H0004295 19,50 26,40 -
Note - Items above with (-) in the Product Code column are available on special request. - Components are tested to IEC 61238-1.
Stranded 3 Core 4 Core
a
Insulated Bootlace Ferrules
Cable SizeColour Items Per Bag Product
Code(mm2)
0,25 Yellow
500
O0012998
0,5 White O0012980
0,75 light Blue O0012999
1 Red O0012984
1,5 Black O0012987
2,5 grey O0013000
4 orange O0013002
6 green
100
O0013004
10 Brown O0012942
16 White O0012945
35 Black 50 O0013005
FERRULES AND TOOLS
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
26
PRe-INSulateD teRMINalS
W
F
L
Model Wire Range
ColourStud Size Dimensions Product
Code(mm²) (mm) W l F
1R3
0,25-1,65 Red
3,2 5,5 17,5 5,0 H0000526
1R4 4,38,0 20,5 7,0
H0000527
1R5 5,3 H0000528
1R6 6,411,6 26,8 11,0
H0000529
1R8 8,4 H0000530
1R10 10,5 13,6 30,5 13,9 H0000525
2R35
1,04-2,63 Blue
3,7 6,6 17,8 6,6 H0000532
2R4 4,3 8,521,8
8,5 H0000533
2R5 5,3 9,5 9,5 H0000534
2R6 6,412,0 26,8 11,0
H0000535
2R8 8,4 H0000536
2R10 10,5 13,6 30,5 13,9 H0000531
3R35
2,63-6,64 Yellow
3,7 7,2 22,7 6,1 H0000539
3R4 4,39,5 26,6 9,1
H0000540
3R5 5,3 H0000541
3R6 6,4 12,0 29,5 10,5 H0000542
3R8 8,415,0 34,0 13,5
H0000543
3R10 10,5 H0000537
3R12 12,0 19,2 38,6 16,0 H0000538
W
F
L
ModelWire Range
ColourStud Size Dimensions Product
Code(mm²) (mm) W l F
1S35
0,25-1,65 Red
3,76,4
21,0 6,5
H0000306
1S4A 4,3 H0000307
1S5A 5,3 8,1 H0000308
1S6A 6,4 9,5 H0000309
2S35
1,04-2,63 Blue
3,7 6,0 H0000310
2S4A 4,3 6,4 H0000311
2S5A 5,3 7,9 H0000312
2S6A 6,4 9,3 H0000313
3S4A
2,63-6,64 Yellow
4,3 8,3
25,5 7,0
H0000314
3S5 5,39,0
H0000315
3S6A 6,4 H0000316
W
F
L
Model Wire Range
ColourDimensions Product
Code(mm²) W l F
1P10 0,25-1,65 Red
1,9
19,8 10,0
H0000371
2P10
1,04-2,63 Blue
H0000372
2P12 21,8 12,0 -
3P13 2,63-6,64 Yellow 2,8 27,0 13,0 H0000373
PRE-INSULATED RING TERMINALS
PRE-INSULATED SPADE TERMINALS
PRE-INSULATED PIN TERMINALS
Note - Items above with (-) in the Product Code column are available on special request. - Lead times need to be confirmed at the time the order is placed.
W
F
F
F
l
l
l
W
W
0.5 - 1,5mm² - 19Amp 600V 1.5 - 2,5mm² - 27Amp 600V 4 - 6mm² - 48Amp 600V
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
27
Note - Items above with (-) in the Product Code column are available on special request. - Lead times need to be confirmed at the time the order is placed.
C
L
D
ModelWire Range
ColourDimensions Product
Code(mm²) D C l
1UT 0,25-1,65 Red 4,0 1,7 24,6 H0000120
2UT 1,04-2,63 Blue 4,5 2,3 24,6 H0000123
3UT 2,63-6,64 Yellow 6,3 3,4 26,5 H0000128
L
W
F
ModelWire Range
ColourDimensions Product
Code(mm²) W l F
1FB10
0,25-1,65 Red
2,3 19,8 10,0 H0000512
1FB113,0
20,8 11,0 H0000513
1FB14 23,8 14,0 H0000514
1FB18 2,2 27,8 18,0 H0000515
2FB91,04-2,63 Blue
2,8 18,8 9,0 H0000516
2FB18 2,2 27,8 18,0 H0000517
3FB102,63-6,64 Yellow
2,8 23,0 10,0 H0000519
3FB14 4,5 27,0 14,0 H0000520
L
W
F
ModelWire Range
ColourDimensions Product
Code(mm²) W l F
1HB3
0,25-1,65 Red
3,0
27,2 16,8
H0000522
1HB
4,6
H0000521
2HB 1,04-2,63 Blue H0000523
3HB 2,63-6,64 Yellow 30,2 17,2 H0000524
W
F
L
ModelWire Range
ColourDimensions Product
Code(mm²) W l F
1DM40,25-1,65 Red
4,80 19 6,5 -
1DM 6,35 21 7,7 H0000504
2DM41,04-2,63 Blue
4,80 10 6,5 H0009960
2DM6,35
217,7
H0000508
3DM 2,63-6,64 Yellow 24 H0000511
PRE-INSULATED FERRULES
PRE-INSULATED BLADE TERMINALS
PRE-INSULATED HOOK BLADE TERMINALS
PRE-INSULATED MALE DISCONNECTS
C
l
l
l
l
F
F
F
D
W
W
W
PRe-INSulateD teRMINalS
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
28
W
F
L
ModelWire Range
ColourDimensions Product
Code(mm²) W l F
1DF2
0,25-1,65 Red
3,2 18,6 6,5 H0000503
1DF4 5,0 19,0 6,4 H0010249
1DF 6,6 20,5 7,3 H0000502
2DF4
1,04-2,63 Blue
5,0 19,0 6,4 H0000507
2DF 6,6 20,5 7,3 H0000506
2DF9 10,0 25,5 12,0 -
3DF2,63-6,64 Yellow
6,6 23,5 7,3 H0000510
3DF9 10,0 28,5 12,0 H0010251
W
F
L
ModelWire Range
ColourDimensions Product
Code(mm²) W l F
F1DF2
0,25-1,65 Red
3,8 19,06,4
-
F1DF4 5,0 19,3 -
F1DF 6,6 22,0 7,3 -
F2DF41,04-2,63 Blue
5,0 19,3 6,4 -
F2DF6,6
22,07,3
-
F3DF2,63-6,64 Yellow
24,0 -
F3DF9 10,0 28,5 12,0 -
W
L
F
ModelWire Range
ColourDimensions Product
Code(mm²) W l F
1PB 0,25-1,65 Red
6,6 22,0 8,0
H0002330
2PB 1,04-2,63 Blue H0002329
W
L
F
ModelWire Range
ColourDimensions Product
Code(mm²) W l F
1ULM4 0,25-1,65 Red
4,0
21,5
8,5
H0002303
2ULM4 1,04-2,63 Blue H0000553
3ULM4
2,63-6,64 Yellow 24,0
-
3ULM5 5,0 H0000549
PRE-INSULATED FEMALE DISCONNECTS
FULLY INSULATED FEMALE DISCONNECTS
PRE-INSULATED PIGGY BACK DISCONNECTS
PRE-INSULATED MALE BULLET DISCONNECTS
l
l
l
l
F
F
F
F
W
W
W
W
PRe-INSulateD teRMINalS
Note - Items above with (-) in the Product Code column are available on special request. - Lead times need to be confirmed at the time the order is placed.
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
29
W
L
F
ModelWire Range
ColourDimensions Product
Code(mm²) W l F
1ULF4 0,25-1,65 Red
3,9
21,5
7,3
H0002302
2ULF4
1,04-2,63 Blue 25,5
H0002304
2ULF5 5,9
7,0
-
3ULF4 2,63-6,64 Yellow 4,9 24,5 H0009491
WL
ModelWire Range
ColourDimensions Product
Code(mm²) W l
1QS 0,25 Red
20,0 27,0
H0000387
2QS 2,0 Blue H0000388
3QS 5,5 Yellow 20,5 34,5 H0000074
PRE-INSULATED FEMALE BULLET DISCONNECTS
QUICK SPLICE CONNECTORS
0.5 - 1,5mm² - 19Amp 600V 1.5 - 2,5mm² - 27Amp 600V 4 - 6mm² - 48Amp 600V
E - InsulatedL
F
BW
CD
W
ModelWire Range
DimensionsProduct Code(mm)
(mm²) Colour l F W B C D
E0510 0,5 White
10,0
16,0 2,6 6,0 1,0 1,3 H0000111
E0710 0,75 Blue
16,3 3,0
6,3
1,2 1,5 H0000112
E01010 1,0 Red 1,4
1,7
H0000113
E01510 1,5 Black 16,4 3,5 2,0 H0000114
E02512 2,5 grey
12,0
19,4
4,0
7,4
2,3 2,6 H0000116
E4012 4,0 orange 4,5 2,8 3,2 H0000117
E6012 6,0 green 20,5 6,0 8,5 3,5 3,9 H0000118
E10012 10,0 Brown 20,8 7,5 8,8 4,5 4,9 H0010261
BOOTLACE
l
l
D
l
F
BW
C
W
F
W
W
PRe-INSulateD teRMINalS
Note - Items above with (-) in the Product Code column are available on special request. - Lead times need to be confirmed at the time the order is placed.
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
30
PRe-INSulateD teRMINalSPRE-PACKS
type Model DescriptionQuantity of each
ComponentContent Product
Code
K150TPre-insulated 105 pcs.
Terminal Kit complete with Crimping Tool
10
5
1R4, 2R4, 2R5, 1S35, 2S35, 1UT, 2UT
3R5, 3S5, 3UT, 1DF, 2DF, 1DM, 2DM
LY2001 (Crimping Tool)
O0002001
K175 Pre-insulated 135 pcs. Terminal Kit
15
10
5
2R35A
1UT, 2UT, 1DF, 2DF, 1DM, 2DM, 1R4, 1R5, 2R4, 2R5,
1S35
3UT, 3R5
No Tool
H0010281
K300 Pre-insulated 235 pcs.Terminal Kit
25
20
15
10
5
1R4, 1R5, 1S35
2R4, 1DF, 2DF, 1DM, 2DM
2R35A
2R5, 1UT, 2UT
3R5, 3R6, 3UT
No Tool
H0010282
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
31
PRE-PACKS
PRe-INSulateD teRMINalS
Note - Items above with (-) in the Product Code column are available on special request.
type Model Pack Number Colour Quantity Per Pack Product Code
Pre-insulated Ring Terminals 6mm PRPK1 (1R6) 1 Red 10 -
Pre-insulated Ring Terminals 5mm PRPK2 (1R5) 2 Red 10 H0001154
Pre-insulated Ring Terminals 4mm PRPK3 (1R4) 3 Red 10 H0001161
Pre-insulated Ring Terminals 6mm PRPK4 (2R6) 4 Blue 8 H0001167
Pre-insulated Ring Terminals 5mm PRPK5 (2R5) 5 Blue 10 H0001169
Pre-insulated Ring Terminals 4mm PRPK6 (2R4) 6 Blue 10 H0001246
Pre-insulated Ring Terminal 8mm PRPK7 (3R8) 7 Yellow 6 H0001247
Pre-insulated Ring Terminals 6mm PRPK8 (3R6) 8 Yellow 6 H0001170
Pre-insulated Ring Terminal 5mm PRPK9 (3R5) 9 Yellow 6 H0001249
Pre-insulated Spade Terminal 3,5mm PRPK10 (1S35) 10 Red 10 H0001144
Pre-insulated Spade Terminal 4mm PRPK11 (1S4A) 11 Red 10 H0001145
Pre-insulated Spade Terminal 3,5mm PRPK12 (2S35) 12 Blue 10 H0001146
Pre-insulated Spade Terminal 5mm PRPK13 (2S5A) 13 Blue 10 H0001147
Pre-insulated Pin Terminal 10mm PRPK14 (1P10) 14 Red 10 H0001148
Pre-insulated Pin Terminal 12mm PRPK15 (2P12) 15 Blue 10 -
Pre-insulated Butt Terminal PRPK16 (1UT) 16 Red 10 H0001150
Pre-insulated Butt Terminal PRPK17 (2UT) 17 Blue 8 H0001151
Pre-insulated Male Disc 6,35mm PRPK18 (1DM) 18 Red 10 H0001152
Pre-insulated Male Disc 6,35mm PRPK19 (2DM) 19 Blue 10 H0001153
Pre-insulated Female Disc 6,35mm PRPK20 (1DF) 20 Red 10 H0001155
Pre-insulated Female Disc 6,35mm PRPK21 (2DF) 21 Blue 10 H0001156
Pre-insulated Piggyback 6,35mm PRPK22 (1PB) 22 Red 10 H0001369
Pre-insulated Piggyback 6,35mm PRPK23 (2PB) 23 Blue 6 H0001370
Pre-insulated Bullet Male PRPK24 (1ULM4) 24 Red 8 H0001157
Pre-insulated Bullet Male PRPK25 (2ULM4) 25 Blue 8 H0001158
Pre-insulated Bullet Female PRPK26 (1ULF4) 26 Red 8 H0001159
Pre-insulated Bullet Female PRPK27 (2ULF4) 27 Red 8 H0001160
Pre-insulated Spade Terminal 5mm PRPK30 (1S5A) 30 Red 10 H0001162
Pre-insulated Spade Terminal 4mm PRPK31 (2S4A) 31 Blue 10 H0001163
Pre-insulated Female Disc 2,5mm PRPK32 (1DF2) 32 Red 10 H0001320
Pre-insulated Female Disc 4,75mm PRPK33 (1DF4) 33 Red 10 H0001164
Pre-insulated Female Disc 4,75mm PRPK34 (2DF4) 34 Blue 10 H0001321
Pre-insulated Female Disc 6,35mms PRPK35 (3DF) 35 Yellow 8 H0001165
Pre-insulated Male Disc 6,35mm PRPK36 (3DM) 36 Yellow 8 H0001166
Pre-insulated Female Disc 9,4mm PRPK37 (3DF9) 37 Yellow 5 H0001242
Pre-insulated Female Full Ins. Disc 6,35mm PRPK38 (F1DFY) 38 Red 5 H0001371
Pre-insulated Female Full Ins. Disc 6,35mm PRPK39 (F2DFY) 39 Blue 5 H0001243
Pre-insulated Butt Terminal PRPK40 (3UT) 40 Yellow 6 H0001168
Pre-insulated Ring Terminal 10mm PRPK41 (3R10) 41 Yellow 5 H0001245
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
32
BRaSS teRMINalS
C
W
L
ModelWire Range Dimensions
Product Code(mm²) l C W
UDF
0,5-2,0
19,0 7,5 6,6 H0003078
UDF 2 16,0 6,4 3,2 H0009908
C
W
L
ModelWire Range Dimensions
Product Code(mm²) l C W
UDM 0,5-2,0 20,0 7,5 6,3 H0007479
UNINSULATED DISCONNECT - FEMALE
UNINSULATED DISCONNECT - MALE
W
W
C
C
l
l
Note - Lead times need to be confirmed at the time the order is placed.
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
33
3M taPeS VINYL ELECTRICAL TAPES
CORROSION PROTECTION TAPES
SPECIALITY TAPES
type Name Descriptionthickness temperature
Rating application Size Product Code
(mm) (°C)
Scotch 27 Glass Cloth Tape
Woven insulating glass cloth. High
temperature resistance. High
mechanical strength. UL recognised.
0,18mm 27 is Class B temp 130
Heat-stable insulation for furnace and
oven controls, motor leads and
switches
12mm x 20m H0001306
19mm x 20m H0001307
12mm x 55m H0002670
25mm x 55m -
type Name Descriptionthickness temperature
Rating application Size Product Code
(mm) (°C)
Scotchwrap® 50 & 51
All weather Corrosion Protection
Tape
All weather performance and
resistance. Resistant to impact and abrasions.
0,25
80Corrosion
protection on pipes, conduits,
joints, etc.
Various x 30m
H0002625
0,5 H0000482
Note - Items above with (-) in the Product Code column are available on special request.
type Name Descriptionthickness temperature
Rating application Size Product Code
(mm) (°C)
Scotch® Super 33+ Premium
Vinyl Electrical Tape
Highly conformable in all weather applications.
Resists UV rays, abrasion,corrosion, alkalis acids. Flame retardant UL
listed. CSA certified.
0,18
105
Primary insulation for splices up to 600V. Protective
jacketing.
19mm x 20m
H0001420
Scotch 35 Colour Coding
Tape
9 fade resistant colours, excellent insulating
properties. Resists UV rays, abrasion, corrosion, alkalis
and acids
Phase identification and marking.
Insulating electrical wiring.
H0000477
H0000478
H0000479
H0000480
H0000481
Scotch 22 Heavy Duty Vinyl Electrical Tape
Thicker for increased mechanical strength. Abrasion resistant. UL listed. CSA certified. Electrical insulating
0,25Primary insulation for splices up to 600V. Protective
jacketing.
24mm x 30m H0001432
36mm x 30m H0000471
3M 33 Vinyl Electrical
Tape
Specification grade vinyl insulation tape. Flame
retardant
0,18 80
Primary insulation for splices up to 600V. Protective
jacketing.
9mm x 6m -
18mm x 6m -
18mm x 20m H0001420
Scotch 1710 Vinyl Electrical
Tape
A good quality electrical vinyl insulating tape.
Flame retardant. SABS122 specified
Excellent resistance to abrasion,
moisture, alkalies, acid and varying
weather conditions.
18mm x 20m
H0001202
H0001203
H0001204
H0001205
H0001206
H0001207
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
34
3M taPeS INSULATING AND SPLICING TAPES
type Name Descriptionthickness temperature
Rating application Size Product Code
(mm) (°C)
Scotch 13 Semi-Conducting
Tape
Highly conformable, semi-conducting EPR (Ethylene Propylene
Rubber) based high-voltage splicing
tape.
0,76 continuous: 90short term: 130
Electrically round out high-voltage connectors and
bond to insulating materials to
minimize electrical stresses.
18mm x 4,5m H0001200
Scotch 23 Self-Fusing
Rubber Tape
High and low voltage insulation, self-fusing
rubber tape.
Primary electrical insulation for
splicing cable from 600V to 69 kV on all solid dielectric
cables.
18mm x 9m H0000472
24mm x 9m H0004081
Scotch 24 Shielding Tape
All-metal, open-weave, shielding braid tape in a flat, cable-like form.
Provides shielding for cable joints on
shielded power cables.
25mm x 4,5m H0001201
Scotch 25 and 26 Grounding Braid
All woven grounding braid in a flat cable-like form. Made of copper.
Ideal for grounding and power
cable shielding applications.
12mm x 4,5m -
25mm x 5m -
Scotch 70 Self-Fusing
Silicone Rubber Tape
A high-temperature, arc- and track-resistant
tape composed of self-fusing, inorganic
silicone rubber.
0,3 180
As an overwrap for protection of
terminating high-voltage
cables against arcing and
tracking.
24mm x 9m H0000483
Scotchfil™ Electrical Insulation
Putty
Non-corrosive, self-fusing adhesive
putty in a flexible tape form.
3,2 80
Used to insulate irregular surfaces like fittings and
valves as well as wire exits at
high-voltage joints.
38mm x 1,5m H0002621
Note - Items above with (-) in the Product Code column are available on special request. - Lead times need to be confirmed at the time the order is placed.
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
35
NItto INSulatIoN taPe
typethickness Width length
Colour Product Code(mm) (mm) (m)
Heavy Duty
0,2 18 20
Red H0000459
green H0000458
Blue H0000457
Yellow H0000462
Black H0000456
White H0000460
light Duty
0,13 19 20
Red H0014411
green H0014410
Blue H0014409
Yellow H0014413
Black H0014408
White H0014412
geNeRal SaFetY taPe
type
Size
Product Code(mm) (mm) (m)
W H l
Barrier tape
75 75 500 H0000485
Detector tape
Skull and crossbones
75 150 500 H0000484
Danger tape
Danger sign
75 150 500 H0001208
Barrier tape
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
36
CaBle tIeS aND StRaPPINg
HELLERMANNTYTON CABLE TIE CHART
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380 390 400 410 420 430 440 450 460 470 480 490 500 510 520 530 540
mm
Nylon Cable ties
Product Code
Cradles
Product Code
Model
Min. tensile Strength
(N) Nylon
Bundle length WidthModel
length Width Height Cable tie Width
(mm) (mm) (mm) Black Natural (mm) (mm) (mm) (mm) Black Natural
T18R 80 22 100 2,5 H0000575 H0000579
TY3 20 14 4,5 Up to 3,5 H0000446 H0000443
TY8 32 25 6,0 Up to 7,5 H0000440 H0000444
T30R 135 35 150 3,5 H0000585 H0000588
T50R
225
50 200
4,6
H0000608 H0000612
T50I 85 300 H0000594 H0000598
T50L 110 390 H0000604 H0000606
T12OS
535
55 225
7,6
O0000206 -
T12OR 105 390 H0000618 H0000619
LK5BK 1115 150 535 13,2 H0000574 -
T18R
T50L
T50R
T12OR
T30R
T12OS
T50I
LK5BK
Note - Items above with (-) in the Product Code column are available on special request.
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
37
Note - Items above with (-) in the Product Code column are available on special request.
CaBle tIeS aND StRaPPINg
type ModelSize
Minimum tensile
Strength
Maximum Cable Bundle
Diameter
Material Product Code
(mm) (N)
MBT5S 127 x 4,6
670,0
25,0
SS316
H0010494
MBT8S 201 x 4,6 50,0 H0010495
MBT14S 362 x 4,6 102,0 H0009101
MBT20S 521 x 4,6 152,0 H0001449
MBT14H 362 x 7,91115,0
102,0 H0006337
MBT20H 521 x 7,9 152,0 H0001448
RELEASE CABLE TIES
MBT RANGE OF 316 STAINLESS STEEL CABLE TIES
type Model
Size average tensile
Strength
Maximum Cable Bundle
Diameter
Product Code
(mm)
REL100 100 x 6,5 26 21 -
REL140 145 x 7,5 30 35 -
REL150 770 x 8,8 100 225 -
REL250 250 x 7,5 30 68 -
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
38
CaBle tIeS aND StRaPPINgME.T NYLON CABLE TIES WITH STAINLESS STEEL TOOTH
The special design of the ME.T cable tie guarantees maximum resistance and safety even in the most extreme applications.
SizeItems Per Bag Colour Maximum
Diameteropening load /
extractionarticle Code
Product Code(mm) (kg/daN)
100 x 2,5
100
White24
18
MET.2.2102R H0010086
Black MET.3.2102R H0010087
200 x 2,5White
55MET.2.2105R H0010176
Black MET.3.2105R H0010088
140 x 3,5White
36
28
MET.2.2110R H0010177
Black MET.3.2110R H0010089
200 x 3,5White
55MET.2.2111R H0010178
Black MET.3.2111R H0010090
280 x 3,5White
80MET.2.2112R H0010179
Black MET.3.2112R H0010091
186 x 4,5White
51
40
MET.2.2123R H0010180
Black MET.3.2123R H0010092
290 x 4,5White
76MET.2.2140R H0010181
Black MET.3.2140R H0010094
360 x 4,5White
101
MET.2.2126R H0010182
Black MET.3.2126R H0010093
360 x 7,5 50White
80MET.2.2534R H0010183
Black MET.3.2534R H0010095
Note - We can supply heat resistant, UV-stabilised, VO self-extinguishing and coloured cable ties to order.
Comparative Cold-Resistance test Comparative tie opening tests
ME.T ME.T
SEL SEL
2,5 3,5 4,5 7,5
-40°C
-30°C
-20°C
-10°C
0°C -40 -25 -40 -25 -25 -15 -25 -15
80 daN
60 daN
40 daN
20 daN
0 daN2,5 3,5 4,5 7,5
18 11 28 20 40 28 80 65
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
39
Self-adhesive Cable Mounts
SizeColour Items per Bag Product Code
(mm)
19 x 19 Natural
100
H0011124
27 x 27
Black H0011102
Natural H0011094
SizeColour Items Per Bag Product Code
(mm)
98 x 2,5Black
100
H0011095
Natural H0011090
140 x 3,5Black H0011096
Natural H0011091
200 x 4,8Black H0011097
Natural H0011092
250 x 4,8 Black H0011104
Natural -
290 x 4,5Black H0011098
Natural H0011093
390 x 4,8
Black H0011106
Natural H0011105
Black H0011108
300 x 7,8 Natural H0011107
365 x 7,5 Black H0011100
365 x 7,8 Natural H0011087
450 x 7,5Black H0011110
Natural H0011109
500 x 12,5Black
50H0011115
Natural H0011089
540 x 7,5Black
100
H0011112
Natural
H0011111
780 x 9,0 H0011113
850 x 12,550
H0013660
1000 x 12,5 Black H0011116
CaBle tIe MouNtS
CaBle tIeS aND aCCeSSoRIeS
Note - Items above with (-) in the Product Code column are available on special request.
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
40
CaBle aND WIRe MaRKeRSOVALGRIP CABLE MARKERS
type Cable Size
Items Per Bag
arrowtagProduct Code
outer Diameter (mm²) tag
lengthCharacters
(mm) (mm) 0 - 9 a - Z
2,5 5,9 100 AT2 63 11 H0001489 H0001490
AT3 100 19 - -
Features and Benefits
Ovalgrip markers have been specifically designed to mark cable and wire both before and after termination.
Their oval shape means that these markers are easy to fit by hand directly onto the cable pre-termination or they can be attached as an identification flag post-termination using special marker Arrowtags. Arrowtags fitted with Ovalgrip are fastened using cable ties and can very easily be modified or removed without the need to uninstall the cable.
Sizes 50 and 85 can be used with Arrowtags for identifying larger cable bundles.
application
Ideally suited to panel building, mass transit, utilities, telecommunications and electrical contracting. Examples:• Packet: 1-3 OD, Letter A, Black on Yellow = HG13MAYL• Reel: 1-3 OD, Number 4, Black on Yellow = HG13M4YL• Reel Kit: A-Z 1-3OD, Black on Yellow = HG13RYLAZ
Note: - Items above with (-) in the Product Code column are available on special request. - Arrowtags will accept HellermannTyton Insulok Cable Ties from 2.5 - 5mm (T18 - T50 Series).
+0 -9 /A Z
type Material Data
Materials Flexible Polyvinyl Chloride, cadmium free (PVC)
Colour White, yellow
operating temperature 65°C to +85°C, Intermittent +135°C
Flammability Self extinguishing
Specification BS 2782-540B, BS 6746C, UL224, IEC 304, IEC 757
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
41
CaBle aND WIRe MaRKeRSHELAGRIP CABLE MARKERS
type Material Data
Materials Flexible Polyvinyl Chloride, cadmium free (PVC)
Colour Yellow
operating temperature -65°C to +105°C. Intermittent +135°C
Flammability Self extinguishing
Specification BS 2782 - 540B, BS 6746C, UL224, IEC 684 - 3 - 113
type Cable Size Items Per
applicator toolsProduct Code*
TJC applicator tools.
outer Diameter Bag
(mm) 0 - 9 a - Z
1,0 - 3,0 500 TJC13 H0001465 H0001466
2,0 - 5,0 500 TJC25 H0001468 H0001469
Features and Benefits
Helagrip is a versatile and cost effective cable identification system. The specially designed internal profile allows one size of marker to be fitted onto a wide range of cable diameters. Helagrip’s chevron cut ensures that the markers lock together, enabling the text legend to stay in place where cable movement or vibration is likely. The flexible material ensures that Helagrip cable markers always fit securely onto the wire.
Note: - Helagrip Markers - Chevron cut available colour coded, black on yellow or black on white.
application
Ideally suited to panel building, mass transit, utilities, telcommunications and electrical contracting. Helagrip is supplied on a reel for ease of use. Markers are available as standard in international resistor colour code and yellow material marked in black. White material marked in black is available on special order. Characters are 0 - 9, A - Z and standard electrical symbols. For smaller cables and wire it is recommended that you use the AD applicator or the TJC installation tool.
• Flexible PVC (High temperature 85°C).• Coding A - Z, 0 - 9 and standard electrical symbols.• Custom marking on request.• HO markers available, black on yellow.• Standard packets of: H085 = 100.• May be fitted directly on the cable or alternatively
onto “Arrow Tags”.
*Note: - Available in yellow only.
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
42
WIRe DuCtSLOTTED TRUNKING
Normal Slot Narrow Slot
DimensionsItems Per Box Product Code
DimensionsItems Per Box Product Code
(W x D) t1 (W x D) t1-e
15 x 18 36 H0011531 25 x 40 36 H0011577
15 x 30 32 H0011532 40 x 40 20 H0011580
25 x 3036
H0011542 60 x 4012
H0011549
25 x 30 BL H0012277 80 x 40 H0011550
15 x 40 24 H0011533 100 x 40 8 H0011557
25 x 40 36 H0011562 25 x 60 24 H0011578
40 x 4020
H0011566 40 x 60 18 H0011581
40 x 40 BL H0012279 60 x 6012
H0011584
60 x 4012
H0011543 80 x 60 H0011551
80 x 40 H0011544 100 x 608
H0011552
100 x 40 8 H0011556 120 x 60 H0011555
25 x 60 24 H0011563 25 x 80 24 H0011579
40 x 6018
H0011567 40 x 80 16 H0011582
40 x 60 BL H0011530 60 x 8012
H0011585
60 x 60
12
H0011570 80 x 80 H0011587
60 x 60 BL H0012280 100 x 80
8
H0011589
80 x 60 H0011545 120 x 80 H0011553
100 x 608
H0011546 40 x 100 H0011583
120 x 60 - 60 x 100
4
H0011586
25 x 80 24 H0011564 80 x 100 H0011588
40 x 80 16H0011559 100 x 100 H0011590
H0011568
60x80
12
H0011571
60x80 BL H0011560
80x80 H0011573
80x80 BL H0011561
100x80
8
H0011575
120x80 H0011547
25x100 H0011565
40x100 H0011569
60x100
4
H0011572
80x100H0011574
H0011591
100x100 H0011576
100x100 BL H0012286
150x100 H0011548
REPLACEMENT COVERS
DimensionsItems Per Box Product Code
(mm)
15
20
H0011534
25 H0011535
40 H0011536
60 H0011537
80 H0011538
100
25
H0011539
120 H0011540
150 H0011541
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
43
type Description Product Code
CONN HIHT 05A/12W H0002488
CONN HIHT 10A/12W + FT H0002491
CONN HIHT 10A/12W + FT H0002492
CONN HIHT 10A/12W + FT/WP H0002493
CONN HIHT 10A/12W H0002494
CONN HIHT 10A/12W + WP H0002495
CONN HIHT 16A/12W+ FT H0002498
CONN HIHT 16A/12W+ FT/WP H0002499
CONN HIHT 16A/12W H0002500
CONN HIHT 16A/12W+ WP H0002501
CONN LOHT 16A/12W BLACK -
CONN LOHT 16A/12W WHITE H0003134
CONN HIHT 32A/12W H0002504
type Description Product Code
3A/12W BLACK H0000088
3A/12W TRANSPARENT H0002490
6A/12W TRANSPARENT H0002497
6A/12W BLACK H0002496
16A/12W BLACK H0002503
16A/12W TRANSPARENT H0003134
32A/12W BLACK H0002505
32A/12W TRANSPARENT H0002506
63A/12W BLACK H0002507
ELECTRO TERMINAL HI-HEAT STRIP CONNECTORS
PVC STRIP CONNECTORS
CoNNeCtoRS
type Description Product Code
Scruit Porcelain MidgetMidget up to 4mm H0000097
Scruit Porcelain NormalNormal up to 10mm H0000099
type Description Product Code
Porcelain in 6A 2-Way CFH C402 H0000079
Porcelain in 15A 2-Way CFH C404 H0000081
Porcelain in 30A 2-Way CFH C406 H0000082
Porcelain in 6A 3-Way CFH C403 H0000084
Porcelain in 15A 3-Way CFH C405 H0000086
Porcelain in 30A 3-Way CFH H0000087
PORCELAIN SCRUITS
PORCELAIN CONNECTORS
Note: - Items above with (-) in the Product Code column are available on special request.
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
44
Heat SHRINK
DimensionsColour
Quantity Per BoxProduct Code
(mm) (m)
1,2-0,6
Black
150
H0011152
1,6-0,8 H0011155
2,4-1,2 H0013239
3,2-1,6 H0013240
4,8-2,4 H0013242
6,4-3,2
75
H0011032
9,5-4,8 H0011036
12,7-6,4 H0011040
19-9,560
H0011044
25,4-12,7 H0011048
38,1-19,1 Blue
30
H0011053
50.8-25,4
Black
H0011176
76,2-38,1 H0011180
102,0-50,8 H0011168
DimensionsColour Product Code
(mm)
10-4
Black
H0011065
14-4,5 H0011066
25-8 H0011067
35-15 H0011068
55-25 H0011069
75-35 H0011070
100-50 H0011071
FLEXIBLE FLAME RETARDED GENERAL PURPOSE HEAT SHRINKABLE POLYOLEFIN TUBING
HEAT SHRINKABLE ADHESIVE LINED POLYOLEFIN END CAPS
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
45
Model Dimensions
Wall thickness
Product Code
Colours
(mm) Red Blue Yellow Black White
CP24P 2,4 - 1,2
0,5
H0000643 - H0000642 H0006314 H0000641 H0000644
CP32P 3,2 - 1,6 H0000647 - H0000646 H0006157 H0000645 H0000648
CP48P 4,8 - 2,4 H0000651 - H0000650 - H0000649 H0000652
CP64P 6,4 - 3,2
0,6
H0000655 - H0000654 H0007429 H0000653 H0000656
CP95P 9,5 - 4,8 H0000659 - H0000658 - H0000657 H0000660
CP127P 12,7 - 6,4 H0000663 - H0000662 - H0000692 H0000664
CP190P 19,0 - 9,5 0,8 H0000667 - H0000666 H0006930 H0000694 H0000668
CP254P 25,4 - 12,7 0,9 H0000671 - H0000670 - H0000696 H0000672
CPPKITBK 2,4 - 4,8 x 10 each / 6,4 - 25,4 x 5 each - (Black) - - - - - -
CPPKITCOL 2,4 - 12,7 x 5 each / 19,0 - 25,4 x 2 each - (Std Colours) H0010417
MINI REELS
PRE - PACKS
Heat SHRINK
Commericial grade Polyolefin
Is ideal for providing insulation of electrical connections, terminals, components and wiring systems. It requires a minimum shrink temperature of 120°C and is well suited to manual as well as automatic methods of application. Is very suitable for use as a continuous insulation sleeve in a variety of industrial applications.
Note - Items above with (-) in the Product Code column are available on special request. - All dimensions in mm except for quantity in metre (m). - Subject to technical changes. - Colours available: Black, Red, Blue, White, Yellow, Green/Yellow, Clear (Clear is not Self Extinguishing).
ModelDimensions
Wall thickness
Product Code
Colour
(mm) Black
CP24R 2,4 - 1,2
0,5
H0000683
CP32R 3,2 - 1,6 H0000685
CP48R 4,8 - 2,4 H0000687
CP64R 6,4 - 3,2
0,6
H0000689
CP95R 9,5 - 4,8 H0000691
CP127R 12,7 - 6,4 H0000693
CP190R 19,0 - 9,5 0,8 H0000695
CP254R 25,4 - 12,7 0,9 H0000697
Yellowgreen
Material Data
type Commercial Grade Polyolefin
Shrink Ratio 2:1
longitudinal Change after Shrinkage ±5%
Minimum Shrink temperature (Metric) +120°C
operating temperature -55°C to +135°C
Dielectric Strength (Metric) 25kV/mm
Flammability Flame retardant except for clear
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
46
typeSize
Product Code(mm)
Flat
White Black
5,0 - -
8,5 K0000805 K0000865
10,5 K0000487 K0000863
12,5 K0000488 -
14,5 K0000808 -
Round
White Black
03 K0000809 -
04 K0000810 -
05 K0000811 -
06 K0000812 -
07 K0000813 -
08 K0000815 K0000814
09 K0000817 K0000816
10 K0000819 K0000818
11 K0000399 K0000820
12 K0000823 K0000822
14 K0000824 -
20 K0000025 -
22 K0000825 -
PuttYCABLE COMPOUND PUTTY
type Description Product Code
• B.I.C.C• 500g Pack H0000068
CaBle ClIPS
Note - Items above with (-) in the Product Code column are available on special request.
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
47
gRoMMetS, PlugS aND StRIPS
Features and BenefitsManufactured from a flexible PVC compound which ensures ease of use. Can be used to protect cables from chafing on bulkheads.
applicationPVC Beading strip is used to protect cables routed through sharp-edged cutout sections. It can also be used to provide an attractive finish to panel edges.
technical Data
type
Width Width Width Width Width Height
Product Code(mm) (mm) (mm) (mm) (mm) (mm)
(W) (W2) (W3) (W4) (H) (H2)
SM1 5,0 1,0 1,8 4,2 6,3 4,9 H0010462
RA1 6,4 2,4 - - 7,1 5,6 H0010463
PS1 1,2 0,6 - - 5,0 3,15 H0010464
Material Data
Material Flexible Polyvinyl Chloride, cadmium free (PVC)
Colour Black (BK)
operating temperature -65°C to +105°C
Flammability Self extinguishing
Note - For full range of grommets, plugs and strips enquire at your nearest branch.
PVC BEADING EDGE PROTECTION STRIP
CABLE A
CCESSORIES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
48
NoteS
CABL
E A
CCES
SORI
ES
Please note: Subject to any applicable laws from time to time: (1) All the product images shown in this catalogue are for marketing purposes and may differ from the actual product. (2) All factual information in this catalogue was correct at the time of going to print and is subject to change without prior notice. Errors and Omissions Excepted. Voltex (Pty) Ltd and its Marketing Agency do not accept responsibility or liability for any incorrect listing of any merchandise or information. Voltex Terms & Conditions of Sale which can be found at www.voltex.co.za and the Disclaimer which is set out at the end of this catalogue apply.
49
NoteS
THE PROVISIONS WHICH ARE CONTAINED HEREIN BELOW ARE SUBJECT TO ANY APPLICABLE LAWS FROM TIME TO TIME:
1. Nothing which is contained in this Catalogue may be construed as an offer to supply or sell any products, or as an inducement or offer to any person to enter into a contract with Voltex (Pty) Ltd and / or its
subsidiaries (collectively and individually referred to hereinafter as “the Company”) in respect of the supply of any products.
2. All the product images shown in this Catalogue (including but not limited to the product features and colours) are for illustration purposes only and may differ from the actual products.
3. Despite every reasonable effort having been made to ensure the accuracy of the technical information contained in this Catalogue:
3.1. THE COMPANY MAKES NO WARRANTY OR REPRESENTATION WHATSOEVER AS TO THE SUITABILITY OF THE PRODUCT FOR ANY PARTICULAR PURPOSE. THE ONUS IS ENTIRELY ON THE PURCHASER OF THE
PRODUCT TO ENSURE THAT THE PRODUCT IS SUITABLE FOR ITS INTENDED PURPOSE;
3.2. DUE TO MATERIAL AND MANUFACTURING TOLERANCES, TEST RESULTS AND / OR LENGTH OF PRODUCT CAN VARY PER INDIVIDUAL PRODUCT. ACCORDINGLY, ALL TECHNICAL DATA SHOWN IN THIS
CATALOGUE IS GIVEN FOR GUIDANCE PURPOSES ONLY. THE COMPANY DOES NOT WARRANT THAT THE PRODUCT WILL MATCH THE TEST RESULTS EXACTLY AND THE COMPANY ACCEPTS NO LIABILITY SHOULD THE
PRODUCT NOT MATCH THE STATED FIGURES.
4. THE COMPANY ACCEPTS NO RESPONSIBILITY FOR ANY LOSS AND / OR DAMAGE OF ANY NATURE WHATSOEVER ARISING FROM THE USE AND / OR RELIANCE ON INFORMATION CONTAINED IN THIS CATALOGUE.
5. Due to continuous product development and improvements, specifications set out in this Catalogue are subject to change without notice.
6. The Company reserves its right to modify and / or discontinue any products depicted in this Catalogue without notice.
7. The products depicted in this Catalogue are, to the best of our knowledge, free of defects at the time of shipment. THE COMPANY’S LIABILITY IN RESPECT OF ANY CLAIM BASED ON DEFECTIVE PRODUCTS
SHALL BE LIMITED TO REPAIRING OR REPLACING SUCH DEFECTIVE PRODUCTS, AT THE DISCRETION OF THE COMPANY, DURING ANY APPLICABLE WARRANTY PERIOD, PROVIDED THAT SUCH DEFECTIVE PRODUCTS
ARE RETURNED TO THE COMPANY, IN THEIR ORIGINAL STATE AND AT THE PURCHASER’S COST, WITHIN THE APPLICABLE WARRANTY PERIOD. IN CIRCUMSTANCES WHERE THE PRODUCTS ARE NOT MANUFACTURED
BY THE COMPANY, THE COMPANY’S LIABILITY UNDER THIS CLAUSE SHALL IN NO CIRCUMSTANCES EXTEND BEYOND ANY CORRESPONDING LIABILITY OF THE MANUFACTURER OR SUPPLIER OF SUCH PRODUCTS TO
THE COMPANY. LIABILITY IS EXPRESSLY DISCLAIMED FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE.
8. Qualified technicians and /or electricians must install all products which require installation by such qualified persons, failing which the Company cannot be held liable for any liability of any nature whatsoever
arising from the purchase of the products.
9. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THE COMPANY (INCLUDING ITS SUBSIDIARIES AND RELATED COMPANIES, DISTRIBUTORS, SUPPLIERS AND WHOLESALERS AND EACH OF THEIR RESPECTIVE
DIRECTORS, OFFICERS, EMPLOYEES, AGENTS, DISTRIBUTORS AND WHOLESALERS) DOES NOT ASSUME ANY LIABILITY FOR AND THE PURCHASER AGREES TO HOLD THE COMPANY HARMLESS AGAINST ANY
LOSS, DAMAGE OR COSTS OF ANY NATURE WHATSOEVER (WHETHER DIRECT, INDIRECT OR CONSEQUENTIAL), ARISING FROM A FAILURE TO USE THE PRODUCTS DEPICTED IN THIS CATALOGUE STRICTLY IN
ACCORDANCE WITH THE INSTRUCTIONS AND WARNINGS CONTAINED ON THE PRODUCT PACKAGING (INCLUDING THE PACKAGE INSERT), WHETHER SUCH LOSS IS TO THE PURCHASER WHO PURCHASED ANY
PRODUCT DEPICTED IN THIS CATALOGUE OR ANY OTHER THIRD PARTY WHICH MAKES USE OF OR BENEFITS FROM THE USE OF SUCH PRODUCT.
10. The Company cannot be held liable for any misapplication of the products, including but not limited to:
10.1. Use in non-standard environments;
10.2. Overloading;
10.3. Use other than that prescribed for the products;
10.4. Use on aluminium or similar softer “fix to” materials.
11. The Company makes no representation as to the availability of any product depicted in this Catalogue.
12. The Company accepts no responsibility and cannot be held liable for any misprints, inaccuracies and / or any errors or omissions in this Catalogue.
No part of this Catalogue (including but not limited to any text and images) may be modified, copied, reproduced, stored, transmitted or distributed in any form or by any mean without the prior written approval of the
Managing Director of the Company.
eaSteRN CaPeEast LondonMthatha Port Elizabeth
043 743 3650047 532 4706 041 504 8200
FRee StateBloemfonteinWelkom
051 505 0700057 396 3191
gauteNgAlbertonAtlas BramleyCenturionDenverEast RandKempton ParkMidrandMontanaPretoriaPretoria NorthRandburgWeltevredenWest Rand
011 907 3752011 864 5255011 887 1308012 653 3090011 616 6269011 918 5220011 970 3290011 315 5800012 524 9600012 330 0211012 546 8111011 792 3380010 007 5181011 951 5780
KWaZulu-NatalBallitoBriardeneDurbanNewcastle
032 946 3966031 573 9200031 310 7900034 315 4150
PietermaritzburgPinetownRichards Bay
033 345 4545031 702 0831035 789 7970
lIMPoPoHoedspruitLephalaleMakhadoPhalaborwaPolokwaneTzaneen
015 793 3703014 763 2215015 516 2075015 781 6409015 297 6177015 307 1213
MPuMalaNgaLydenburgNelspruitWitbank
013 235 4706013 753 3643013 692 8536
NaMIBIaWindhoek OngwedivaSwakopmund
+264 61 418 100+264 65 238 597+264 64 425 000
NoRtH WeStKlerksdorpRustenburg
018 462 9945014 597 1311
BRaNCHeS NATIONWIDE
NoRtHeRN CaPeKathuKimberleyKurumanUpington
053 723 2222053 832 1211053 712 1164054 332 6211
WeSteRN CaPeBlackheathBrackenfellCape TownGeorgeKnysnaMossel BayOverstrandPaarlStrandTable ViewVredenburgWettonWorcester
021 905 1877 021 982 1404021 531 2033044 873 5020044 382 1242044 695 0010028 312 3366021 872 1554021 853 8511021 556 1852022 713 2371021 761 4599023 342 1795
HeaD oFFICe011 879 2000 [email protected] House, St. Andrews Office Park, 39 Wordsworth Avenue, Senderwood, 2007