2003/04CABLE MANAGEMENT SOLUTIONS CATALOGUE
www.legrand.co.ukwww.legrand.co.uk
Distributor :
LEGRAND ELECTRIC LIMITEDDial Lane, West Bromwich, West Midlands, B70 0EB
Customer Services : Tel : 0845 605 4333 Fax : 0845 605 4334E-mail : [email protected]
Technical : Tel : 0845 605 5333 Fax : 0845 605 5334E-mail : [email protected]
DISTRIBUTION CENTRES
1. Glasgow Tel : 0141 764 2200Fax : 0141 764 2201
2. LeedsTel : 0113 233 9950Fax : 0113 233 9964
3. BirminghamTel : 0845 605 4333Fax : 0845 605 4334
4. LondonTel : 01895 458777Fax : 01895 458778
E-mail : [email protected]
D L PASS, Fastrack, Rolfe King, Salamandre, Swifts and the Legrand logo are registered trademarks of theLegrand group of companies.
Mosaic is a trademark of the Legrand group of companies.
CA
BM
AN
07.
2003
.30K
1
2
3
4
2003
/ 04
CA
BL
E M
AN
AG
EM
EN
T S
OL
UT
ION
S C
ATA
LO
GU
E
A COMPLETE CABLE MANAGEMENT SOLUTION FOR COMMERCIAL AND INDUSTRIAL APPLICATIONS
®
®
CABLE TRAY
Swif
ts
QUICK-FIXINNOVATIVECABLE TRAYSYSTEMS
8
The distinctive slot
pattern on Swifts’
cable tray systems
provides installers with
total flexibility for the
positioning of nuts and
bolts, cable ties and all
ancillary items.
Available in five types,
from light through to extra
heavy duty, each system is
offered with a fully
integrated range of time
saving fixings and fittings.Wide choice of types, sizes and finishes
Square-shafted quick boltslock firmly into position before
fixing. The nuts, which haveintegral washers and a
serrated edge to reduce slipand improve earthing, canthen be tightened using a
power tool with just one hand
cable
tra
y s
yst
ems
9
www.legrand.co.uk
CABLE TRAY
Unique adjustable fittingsensure a perfect fit. Adjustable
bends can be set to a fixedangle or adjusted to any
angle between 300 and 900.Adjustable risers can be usedas inside or outside risers for
any angle up to 900
Fittings for all systems withinthe range have integratedcouplings and fishplates,
saving both time and money
See page 272 for details
Rapide... the fastereasier way to designyour cable managementinstallations
10
Swif
ts
cable tray systemsMRF medium duty return flange
Accessories
300mm wide
150mm wide
Couplers
Straight Lengths - 3m
MRFL/ WIDTH / FINISH
50mm wide tray MRFC/50/ FINISH
75 - 900mm wide tray MRFC/ FINISH
For an extensive range of Supportsand Ancillary Items for fast and easyinstallation see pages 20 to 23
Form a large 90° Bend by using2 Adjustable Bends together
Good Idea!
Fishplates page 23
30° Bend
90° Bend
Adjustable Bend
90° Bends
All widths MRFB/ WIDTH / FINISH
60°, 45°, 30° Bends
50 & 450-900mm wideMRFB/ WIDTH / ANGLE / FINISH
Not available in 75-300mm widths.Use Adjustable Bend instead.
Adjustable Bends
50-300mm wide MRFAB/ WIDTH / FINISH
FinishesStandard Finishes:-/G Hot dip galvanized after manufacture
to BS EN ISO 1461.-/PG Pre-galvanized steel to
BS EN 10142 & 3 (BS2989).
Additional Finishes:-/DG Deep Galvanized Corten A steel.-/SS Stainless steel to BS EN 10088 grade
1-4401 (equivalent to 316S31).-/E Plastic coated (to customer's
specification).
Note: MRF 50 wide straight lengths andaccessories not available in -/DG or -/SS.
MRFC/- Couplers MRFC/50/- Coupler
90° Can be set to a fixed angle(in increments of 7.5°) oradjusted to any anglebetween 30° and 90°.
Adjustable BendsNot available in 450 to 900mm widths.Use fixed item instead e.g. MRFB/450/30/G.
125mm
Minimum Cable RadiusBends, Tees and4 Way Crosspieces
Ordering InformationComponent references are obtained bygiving the component code followed by thewidth(s), angle (where needed) and the finishsuffix.EXAMPLES:For a hot dip galvanized MRF StraightLength, 600mm wide:- MRFL/600/GFor a hot dip galvanized MRF 90° InsideRiser, 600mm wide:- MRFIR/600/G
Standard widths:50, 75, 100, 150, 225, 300, 450, 600, 750and 900mm.Widths up to 150mm wide, in -/G and -/PGfinishes, have slots in side flanges.
Minimum cable radius =125mm.
NOTE:To obtain gauges for additional finishes contactour Sales Support (see outside back cover).
Couplers are only required for joiningstraight lengths, all MRF accessories haveintegral couplings.MRFC/50/- one piece unit, supplied singlyMRFC/- supplied in pairs
For trays 450mm wide and greater, theaddition of Fishplate WF/- across the undersideof the tray-to-tray joint provides added strengthand increases the safe working load.
90°
t
-/G
Width, mm t, mm
50 to 100
225
300
0.8
1.0
1.2
-/PG
0.7
0.8
150 0.8 0.8
1.0
450 & 600 1.5 1.4
750 & 900 2.0 2.0
25
Quick Bolt Couplers75 - 900mm wide tray MRQBC/G
75 - 900mm wide tray MRQBC/PG
Supplied in packs containing 25 pairs of couplers and 100coach bolts. For tray widths 300mm and above use twoadditional coach bolts QBF per coupler, see page 23.
For availability of gauges andfinishes not published, contact ourSales Support
11
cable
tra
y s
yst
ems
Unequal Tees
Unequal Tee
Equal Tee
4 Way Crosspiece
Reducer
MRF.2054-IR
Adjustable Riser Extra LongAdjustable Riser
Extra LongAdjustable Risers
MRFAXR/ WIDTH / FINISH
4 Way Crosspieces
MRFX/ WIDTH / FINISH
90°
90°
Minimum radius = 200mm.Maximum radius = 300mm.Overall length when flat = 554mm.
Adjustable Risers Extra Long Adjustable Risers
Adjustable Risers(Inside or Outside)
MRFAR/ WIDTH / FINISH
90° Inside Risers
MRFIR/ WIDTH / FINISH
90° Outside Risers
MRFOR/ WIDTH / FINISH
The Extra Long Adjustable Riser can be used as aninside or outside riser for any angle up to 90°.
Avoid the need for cutting byinserting as many segments asnecessary into the end of thestraight tray.
Good Idea!
W1
W2W1
To complete the component reference add the main runwidth (W1), the reduced run width (W2) and the finish.EXAMPLE:For a hot dip galvanized Unequal Tee reducing from300mm to 150mm:-MRFUT/300/150/G.
W2
W1
To complete the component reference add the main runwidth (W1), the reduced run width (W2) and the finish.EXAMPLE:For a hot dip galvanized Reducer reducing from 300mm to150mm:-MRFR/300/150/G.
Reducers
Equal Tees
MRFT/ WIDTH / FINISH
Unequal Tees
MRFUT/ WIDTH1 / WIDTH2 / FINISH
Reducers
MRFR/ WIDTH1 / WIDTH2 / FINISH
The Adjustable Riser can be used as an inside oroutside riser for any angle up to 90°.
Ideal for avoiding obstacles on site.
Minimum radius = 200mm.Maximum radius = 650mm.Overall length when flat = 1087mm.
90°
90°
90° Outside Riser
90° Inside Riser
SRF to MRFReducer
SRF to MRF Reducers
SRFMRFR/ WIDTH / FINISH
Accessories
cable tray systemsMRF medium duty return flange
12
Swif
ts
125mm
Minimum Cable RadiusBends, Tees and4 Way Crosspieces
Fishplates page 23
Accessories
NOTE:Gauges are given for standard finishes. To obtaingauges for additional finishes contact our SalesSupport (see outside back cover).
Couplers are only required for joining straightlengths, all MRF accessories have integralcouplings.Supplied in pairs.
For trays 450mm wide and greater, theaddition of Fishplate WF/- across the undersideof the tray-to-tray joint provides added strengthand increases the safe working load.
Couplers
SRFL/ WIDTH / FINISH
All tray widths SRFC/ FINISH
Straight Lengths - 3m
90° Bends
All widths SRFB/ WIDTH / FINISH
60°, 45°, 30° Bends
450-900mm wideSRFB/ WIDTH / ANGLE / FINISH
Not available in 75-300mm widths.Use Adjustable Bend instead.
Adjustable Bends
75-300mm wide SRFAB/ WIDTH / FINISH
Couplers
Good Idea!
Form a large 90° Bend by using2 Adjustable Bends together
Adjustable Bend
30° Bend
90° Bend
t
Width, mm t, mm
75 to 150
225 & 300
450
0.9
1.2
1.5
600 to 900 2.0
50
Ordering InformationComponent references are obtained bygiving the component code followed by thewidth(s), angle (where needed) and the finishsuffix.EXAMPLES:For a hot dip galvanized SRF StraightLength, 600mm wide:- SRFL/600/GFor a hot dip galvanized SRF 90° InsideRiser, 600mm wide:- SRFIR/600/G
Standard widths:75, 100, 150, 225, 300, 450, 600, 750 and900mm.
FinishesStandard Finishes:-/G Hot dip galvanized after manufacture
to BS EN ISO 1461.-/PG Pre-galvanized steel to
BS EN 10142 & 3 (BS2989).
Additional Finishes:-/DG Deep Galvanized Corten A steel.-/SS Stainless steel to BS EN 10088 grade
1-4401 (equivalent to 316S31).-/E Plastic coated (to customer's
specification).Can be set to a fixed angle(in increments of 7.5°) oradjusted to any anglebetween 30° and 90°.
Adjustable BendsNot available in 450 to 900mm widths.Use fixed item instead e.g. SRFB/450/30/G.
Minimum cable radius =125mm.
90°
90°
cable tray systemsSRF heavy duty return flange
Quick Bolt CouplersAll tray widths SRQBC/G
All tray widths SRQBC/PG
Supplied in packs containing 25 pairs of couplers and 100coach bolts. For tray widths 300mm and above use twoadditional coach bolts QBF per coupler, see page 23.
For an extensive range of Supportsand Ancillary Items for fast and easyinstallation see pages 20 to 23
For availability of gauges andfinishes not published, contact ourSales Support
13
cable
tra
y s
yst
ems
Reducers
SRFR/ WIDTH1 / WIDTH2 / FINISH
Equal Tees
SRFT/ WIDTH / FINISH
Unequal Tees
SRFUT/ WIDTH1 / WIDTH2 / FINISH
Unequal Tee
Equal Tee
90° Inside Risers
SRFIR/ WIDTH / FINISH
90° Outside Risers
SRFOR/ WIDTH / FINISH
Adjustable Risers(Inside or Outside)
SRFAR/ WIDTH / FINISH
Extra LongAdjustable Risers
SRFAXR/ WIDTH / FINISH
4 Way Crosspieces
SRFX/ WIDTH / FINISH
Unequal Tee
90° Outside Riser
Adjustable RiserExtra LongAdjustable Riser
90° Inside Riser
4 Way Crosspiece
Extra Long Adjustable RisersThe Adjustable Riser can be used as an inside oroutside riser for any angle up to 90°.
Minimum radius = 200mm.Maximum radius = 300mm.Overall length when flat = 554mm.
Adjustable Risers
90°
90°
Reducer
Good Idea!
Avoid the need for cutting byinserting as many segments asnecessary into the end of thestraight tray.
90°
90°
Minimum radius = 200mm.Maximum radius = 650mm.Overall length when flat = 1087mm.
Ideal for avoiding obstacles on site.
To complete the component reference add the main runwidth (W1), the reduced run width (W2) and the finish.EXAMPLE:For a hot dip galvanized Reducer reducing from 300mm to150mm:-SRFR/300/150/G.
W1
W2W1
To complete the component reference add the main runwidth (W1), the reduced run width (W2) and the finish.EXAMPLE:For a hot dip galvanized Unequal Tee reducing from300mm to 150mm:-SRFUT/300/150/G.
W2
W1
Reducer
SRF to MRFReducer
SRF to MRF Reducers
SRFMRFR/ WIDTH / FINISH
cable tray systemsSRF heavy duty return flange
Accessories
14
Swif
ts
NOTE:When placing orders for 50 to 225 wide tray in -/DGand -/SS finishes, contact our Sales Support .
Fishplates page 23
Accessories
All SS straight lengths and accessorieshave integral couplings, no separatecouplers are needed.
90° Bend
4 Way Crosspiece
30° Bend
Light Gauge
SSL/ WIDTH /L/ FINISH
Heavy Gauge
SSL/ WIDTH /H/ FINISH
90° Bends
SSB/ WIDTH / FINISH
60°, 45°, 30° Bends
SSB/ WIDTH / ANGLE / FINISH
4 Way Crosspieces
SSX/ WIDTH / FINISH
Straight Lengths - 3m
For an extensive range of Supportsand Ancillary Items for fast and easyinstallation see pages 20 to 23
For SS Tray cut to length use fishplates acrosstray-to-tray joint as shown.
FinishesStandard Finishes:-/G Hot dip galvanized after manufacture
to BS EN ISO 1461.-/PG Pre-galvanized steel to
BS EN 10142 & 3 (BS2989).
Additional Finishes:-/DG Deep Galvanized Corten A steel.-/SS Stainless steel to BS EN 10088 grade
1-4401 (equivalent to 316S31).-/E Plastic coated (to customer's
specification).
Ordering InformationComponent references are obtained bygiving the component code followed by thewidth(s), angle (where needed) and the finishsuffix.EXAMPLES:For a hot dip galvanized heavy duty SSStraight Length, 600mm wide:-SSL/600/H/GFor a hot dip galvanized SS 90° InsideRiser, 600mm wide:- SSIR/600/G
Standard widths:50, 75, 100, 150, 225, 300, 450, 600, 750and 900mm.Most widths of SS Tray are available ineither light (- /L/ -) or heavy (- /H/ -) gaugevariants, see table alongside.
100mm wide
300mm wide
Note:
50-300mm wideFishplate F/-
450-900mm wideFishplate WF/-
Typical fastenerpositions shown.Use suitablealigning holes.
cable tray systemsSS light duty
t
50 to 22512
t
18
300 to 900
Traywidthmm
OrderingCodes
Finishes Availabletmm /G /SS /E/PG /DG
50507575
100100150150225225300450450600750900
-/PG Finish:SSL/300/H/- t = 1.4 SSL/450/L/- t = 1.4
0.91.50.91.50.91.50.91.50.91.51.51.52.02.02.02.0
**
*
SSL/50/L/-SSL/50/H/-SSL/75/L/-SSL/75/H/-SSL/100/L/-SSL/100/H/-SSL/150/L/-SSL/150/H/-SSL/225/L/-SSL/225/H/-SSL/300/H/-SSL/450/L/-SSL/450/H/-SSL/600/H/-SSL/750/H/-SSL/900/H/-
For availability of gauges andfinishes not published, contact ourSales Support
15
cable
tra
y s
yst
ems
90° Outside Riser
Adjustable Riser
90° Inside Riser
Unequal Tee Reducer
Unequal Tee
Equal Tee
Reducer
W
W2
1
Inside and Outside RisersInside and Outside Risers are not available in/PG finish, use Adjustable Risers for all anglesfrom 0° to 90°, reference SSAR/WIDTH/FINISH
W2
W
W1
1
To complete the component reference add themain run width (W1), the reduced run width (W2)and the finish.EXAMPLE:For a hot dip galvanized Unequal Tee reducingfrom 300mm to 150mm:-SSUT/300/150/G.
To complete the component reference add themain run width (W
1), the reduced run width (W
2)
and the finish.EXAMPLE:For a hot dip galvanized Reducer reducing from300mm to 150mm:-SSR/300/150/G.
Equal Tees
SST/ WIDTH / FINISH
Unequal Tees
SSUT/ WIDTH1 / WIDTH2 / FINISH
Reducers
SSR/ WIDTH1 / WIDTH2 / FINISH
90° Inside Risers
SSIR/ WIDTH / FINISH
90° Outside Risers
SSOR/ WIDTH / FINISH
60°, 45°, 30° Inside Risers
SSIR/ WIDTH / ANGLE / FINISH
60°, 45°, 30° Outside Risers
SSOR/ WIDTH / ANGLE / FINISH
Adjustable Risers
SSAR/ WIDTH / FINISH
The Adjustable Riser can be used as an inside oroutside riser for any angle up to 90°.
Adjustable Risers
90°
90°
Minimum radius = 200mm.Maximum radius = 300mm.Overall length when flat = 554mm.
cable tray systemsSS light duty
Accessories
16
Swif
ts
For SH Tray cut to length use fishplatesacross tray-to-tray joint as shown.
Fishplates page 23
AccessoriesStraight Lengths - 2.4m
SHL/ WIDTH / FINISH
All SH straight lengths and accessorieshave integral couplings, no separatecouplers are needed.
FINISHESStandard Finish:-/G Hot dip galvanized after manufacture
to BS EN ISO 1461.
Additional Finishes:-/DG Deep Galvanized Corten A steel.-/SS Stainless steel to BS EN 10088 grade
1-4401 (equivalent to 316S31).-/E Plastic coated (to customer's
specification).
90° Bends
SHB/ WIDTH / FINISH
60°, 45°, 30° Bends
SHB/ WIDTH / ANGLE / FINISH
90° Bend
30° Bend
t
Width, mm t, mm
100 to 300
450 & 600
1.5
2.035
Ordering InformationComponent references are obtained bygiving the component code followed by thewidth(s), angle (where needed) and the finishsuffix.EXAMPLES:For a hot dip galvanized SH Straight Length,600mm wide:- SHL/600/GFor a hot dip galvanized SH 90° InsideRiser, 600mm wide:- SHIR/600/G
Standard widths:100, 150, 225, 300, 450 and 600mm.
Note:
100-300mm wideFishplate F/-
450 & 600mm wideFishplate WF/-
Typical fastenerpositions shown.Use suitablealigning holes.
cable tray systemsSH heavy duty
For an extensive range of Supportsand Ancillary Items for fast and easyinstallation see pages 20 to 23
For availability of gauges andfinishes not published, contact ourSales Support
17
cable
tra
y s
yst
ems
90° Inside Riser
4 Way Crosspiece
90° Outside Riser
Reducer
Unequal Tee
Equal Tee
Unequal Tees
SHUT/ WIDTH1 / WIDTH2 / FINISH
Reducers
SHR/ WIDTH1 / WIDTH2 / FINISH
90° Inside Risers
SHIR/ WIDTH / FINISH
90° Outside Risers
SHOR/ WIDTH / FINISH
60°, 45°, 30° Inside Risers
SHIR/ WIDTH / ANGLE / FINISH
60°, 45°, 30° Outside Risers
SHOR/ WIDTH / ANGLE / FINISH
4 Way Crosspieces
SHX/ WIDTH / FINISH
Equal Tees
SHT/ WIDTH / FINISH
Unequal Tee
W2 W1
W1
To complete the component reference add themain run width (W
1), the reduced run width (W
2)
and the finish.EXAMPLE:For a hot dip galvanized Unequal Tee reducingfrom 300mm to 150mm:-SHUT/300/150/G.
Reducer
W
W2
1
To complete the component reference add themain run width (W1), the reduced run width (W2)and the finish.EXAMPLE:For a hot dip galvanized Reducer reducing from300mm to 150mm:-SHR/300/150/G.
cable tray systemsSH heavy duty
Accessories
18
Swif
ts
XRFL/ WIDTH / FINISH
Straight Lengths - 3m
Couplers
All tray widths XRFC/ FINISH
Couplers
Accessories
Couplers are only required for joining straightlengths, all XRF accessories have integral couplings.Supplied in pairs.
Fishplates page 23
For all trays 225mm wide and greater (whencable loading is in excess of 50% of themaximum safe working load), the addition of aFishplate across the underside of the tray-to-trayjoint provides added strength and increases thesafe working load.225mm wide: Fishplate F/-300mm wide: Fishplate MF/-450-600mm wide: Fishplate WF/-
90° Inside Risers
XRFIR/ WIDTH / FINISH
90° Outside Risers
XRFOR/ WIDTH / FINISH
60°, 45°, 30° Inside Risers
XRFIR/ WIDTH / ANGLE / FINISH
60°, 45°, 30° Outside Risers
XRFOR/ WIDTH / ANGLE / FINISH
t
Width, mm t, mm
100 to 300
450 & 600
1.5
2.0
80
Inside and Outside Risers
Use M6x16mm roofing bolts or similarfastenings (not included).
Ordering InformationComponent references are obtained bygiving the component code followed by thewidth(s), angle (where needed) and the finishsuffix.EXAMPLES:For a hot dip galvanized XRF StraightLength, 600mm wide:- XRFL/600/GFor a hot dip galvanized XRF 90° InsideRiser, 600mm wide:- XRFIR/600/G
Standard widths:100, 150, 225, 300, 450 and 600mm.
FinishesStandard Finish:-/G Hot dip galvanized after
manufacture to BS EN ISO 1461.
Additional Finishes:-/DG Deep Galvanized Corten A steel.-/SS Stainless steel to BS EN 10088 grade
1-4401 (equivalent to 316S31).
Width, mm
INSIDE RISER
R
R
OUTSIDE RISER
Radius (R), mm
100 to 300
450 & 600
180
240
90° Inside Riser
90° Outside Riser
cable tray systemsXRF extra heavy duty return flange
For an extensive range of Supportsand Ancillary Items for fast and easyinstallation see pages 20 to 23
For availability of gauges andfinishes not published, contact ourSales Support
19
cable
tra
y s
yst
ems
Reducer
Unequal Tee
Unequal Tee
Equal Tee
W2W1
W1
Reducers
XRFR/ WIDTH1 / WIDTH2 / FINISH
Equal Tees
XRFT/ WIDTH / FINISH
Unequal Tees
XRFUT/ WIDTH1 / WIDTH2 / FINISH
To complete the component reference add themain run width (W1), the reduced run width (W2)and the finish.EXAMPLE:For a hot dip galvanized Unequal Tee reducingfrom 300mm to 150mm:-XRFUT/300/150/G.
To complete the component reference add themain run width (W1), the reduced run width (W2)and the finish.EXAMPLE:For a hot dip galvanized Reducer reducing from300mm to 150mm:-XRFR/300/150/G.
W
2W
1
4 Way Crosspiece
90° Bend
90° Bends
XRFB/ WIDTH / FINISH
60°, 45°, 30° Bends
XRFB/ WIDTH / ANGLE / FINISH
4 Way Crosspieces
XRFX/ WIDTH / FINISH
30° Bend
Minimum Cable RadiusBends, Tees and 4 Way Crosspieces
R
Reducer
Width, mm Radius (R), mm
100 to 300
450 & 600
180
250
cable tray systemsXRF extra heavy duty return flange
Accessories
20
Swif
ts
Light Duty Cantilever Bracket
Tray to Support fastenings:Roofing Bolts, Nuts and Washers page 23
Threaded Rods page 23
Channel Nuts page 79
Beam Clamps page 86
Supports
Light Duty Cantilever ArmsSupplied singly without fastenings.Fit horizontal runs of tray and Opal ladder to flatsurface and Swiftrack channel. Suitable for alltray widths.
Light Duty Cantilever BracketsSupplied singly without fastenings.Fit horizontal runs of lightly loaded tray up to150mm wide to flat surfaces and Swiftrackchannel.
SWL, kgf*A L surface SwiftrackRef.
LCB/50/-LCB/75/-LCB/100/-LCB/150/-
37374545
5075105150
15152020
15152020
*Per bracket for load uniformly distributed acrosscomplete bracket.
Light Duty Cantilever Arm
Light Duty Cantilever Brackets are notavailable in -/PG finish.
*Per cantilever arm for load uniformly distributedacross complete arm using two fixing holes.Safety factor: 2.1 When one fixing hole is used the recommendedsafe working load = 100 kgf.
A LRef.3030454575
125175225
LCA/100/-LCA/150/-LCA/225/-LCA/300/-LCA/450/-LCA/600/-LCA/750/-LCA/900/-
140190265340490640790940
Light Duty Cantilever Arms
100mm wide tray LCA/100/ FINISH
150mm wide tray LCA/150/ FINISH
225mm wide tray LCA/225/ FINISH
300mm wide tray LCA/300/ FINISH
450mm wide tray LCA/450/ FINISH
600mm wide tray LCA/600/ FINISH
750mm wide tray LCA/750/ FINISH
900mm wide tray LCA/900/ FINISH
Light Duty Cantilever Brackets
50mm wide tray LCB/50/ FINISH
75mm wide tray LCB/75/ FINISH
100mm wide tray LCB/100/ FINISH
150mm wide tray LCB/150/ FINISH
Finishes
Standard Finishes:-/G Hot dip galvanized after manufacture
to BS EN ISO 1461.-/PG Pre-galvanized steel to
BS EN 10142 & 3 (BS2989).
Additional Finishes:-/DG Deep Galvanized Corten A steel.
-/SS Stainless steel to BS EN 10088 grade1-4401 (equivalent to 316S31).
-/E Plastic coated (to customer'sspecification).
surface1201
1201
150150150300300300
SWL, kgf*
40
L
A
Ø11 HOLES
L
AA
50-75 100-150
Ø11 HOLESIN CENTRE SLOTS
25x8 SLOTS
cable tray systemssupports
21
cable
tra
y s
yst
ems
Stand-Off Brackets
Light Duty Trapeze Hanger
A SWL, kgf*Ref.LTH/50/-LTH/75/-LTH/100/-LTH/150/-LTH/225/-LTH/300/-LTH/450/-LTH/600/-LTH/750/-LTH/900/-
75112150187280355505660810960
100100100100200270300300300300
*Per hanger for loaduniformly distributedacross completehanger.
Safety factor: 2.
Trapeze Hangerto Threaded Rodfixing
Light Duty Trapeze HangersSupplied singly without fastenings.Support horizontal runs of tray and Opal ladderfrom overhead structure.Up to 450mm wide use M10 threaded rods. For600mm wide and above use M12 threaded rods.
*Per stand-off bracket for load uniformlydistributed across the tray.
ARef. horizontaltray run
STB/50/-STB/75/-STB/100/-STB/150/-STB/225/-STB/300/-STB/450/-STB/600/-STB/750/-STB/900/-
40404040
100100150150150150
82120157195273349485635785935
Stand-Off Brackets Supplied singly withoutfastenings.Fit vertical or horizontalruns of tray to verticalsurface, floor andSwiftrack channel.
Central hole equispaced on600 to 900 wide brackets.
Stand-Off Brackets
50mm wide tray STB/50/ FINISH
75mm wide tray STB/75/ FINISH
100mm wide tray STB/100/ FINISH
150mm wide tray STB/150/ FINISH
225mm wide tray STB/225/ FINISH
300mm wide tray STB/300/ FINISH
450mm wide tray STB/450/ FINISH
600mm wide tray STB/600/ FINISH
750mm wide tray STB/750/ FINISH
900mm wide tray STB/900/ FINISH
Overhead HangersSupplied singly without fastenings.Support horizontal runs of lightly loaded tray upto 150mm wide from overhead structure.Use M10 threaded rod.
Ref.OH/50/-OH/75/-OH/100/-OH/150/-
SWL, kgf*25505050
*Per hanger for loaduniformly distributedacross tray width.
Safety factor: 2.
Overhead Hanger
60
450-900mmwide
40
50-300mmwide
Overhead Hangers
50mm wide tray OH/50/ FINISH
75mm wide tray OH/75/ FINISH
100mm wide tray OH/100/ FINISH
150mm wide tray OH/150/ FINISH
Light Duty Trapeze Hangers
50mm wide tray LTH/50/ FINISH
75mm wide tray LTH/75/ FINISH
100mm wide tray LTH/100/ FINISH
150mm wide tray LTH/150/ FINISH
225mm wide tray LTH/225/ FINISH
300mm wide tray LTH/300/ FINISH
450mm wide tray LTH/450/ FINISH
600mm wide tray LTH/600/ FINISH
750mm wide tray LTH/750/ FINISH
900mm wide tray LTH/900/ FINISH
SWL, kgf*verticaltray run
——————
150150150150
50-150
225-450
A
A
Ø11 HOLESIN CENTRE SLOTS
Ø11 HOLES600-900 Ø14 HOLES
A
50-300 450-900
A
Ø11 HOLESIN CENTRE
SLOTS
Ø11 HOLES
cable tray systemssupports
Supports
22
Swif
ts
Straight Closed Covers3.0m MRFCC/ WIDTH / FINISH
3.0m SRFCC/ WIDTH / FINISH
3.0m SSCC/ WIDTH / FINISH
2.4m SHCC/ WIDTH / FINISH
3.0m XRFCC/ WIDTH / FINISHStraight Ventilated Covers3.0m MRFCV/ WIDTH / FINISH
3.0m SRFCV/ WIDTH / FINISH
3.0m SSCV/ WIDTH / FINISH
2.4m SHCV/ WIDTH / FINISH
Divider to Tray fastenings:Roofing Bolts, Nuts and Washers page 23
Ancillary Items
Dividers - 3.0mMRFDV/ FINISH
SRFDV/ FINISH
SSDV/ FINISH
SHDV/ FINISH
XRFDV/ FINISH
Earth Continuity Connectors
pack 20 PTFEB
DividerStandard length 3.0m
Earth Continuity Connector
StraightClosed Cover Accessory
Closed Cover
AccessoryVentilated Cover
Accessory Closed Covers
Supplied singly with fastenings.The product code should be completed with theinclusion of the accessory reference whereindicated.EXAMPLE:A Closed Cover for an SRF Unequal Tee,SRFUTCC / WIDTH1 / WIDTH2 / FINISH
Accessory Ventilated Covers
Supplied singly with fastenings.The product code should be completed with theinclusion of the accessory reference whereindicated.EXAMPLE:A Ventilated Cover for an SRF Unequal Tee,SRFUTCV / WIDTH1 / WIDTH2 / FINISH
Straight Closed CoversSupplied singly with fastenings.Covers 600mm and above are overlap jointedand dimpled for rigidity.SS Closed Covers are only available in widths300mm and above.
Straight Ventilated Covers
Supplied singly with fastenings.Covers 600mm and above are overlap jointedand dimpled for rigidity.SS Ventilated Covers are only available in widths75mm and above.
Accessory Closed CoversMRF (Acc) CC/ WIDTH(S) / FINISH
SRF (Acc) CC/ WIDTH(S) / FINISH
SS (Acc) CC/ WIDTH(S) / FINISH
SH (Acc) CC/ WIDTH(S) / FINISH
XRF (Acc) CC/ WIDTH(S) / FINISHAccessory Ventilated Covers
MRF (Acc) CV/ WIDTH(S) / FINISH
SRF (Acc) CV/ WIDTH(S) / FINISH
SS (Acc) CV/ WIDTH(S) / FINISH
SH (Acc) CV/ WIDTH(S) / FINISH
StraightVentilated Cover
DividersSupplied singly without fastenings.Used to physically separate different types orgroups of cable within one cable tray run.
Earth Continuity ConnectorsFastenings not included.Use M6 x 12mm roofing nuts and bolts.Copper braid and copper lugs, both inelectrotinned finish.Length between centres: 93mm.Conductor area: 4mm2.
Connector to Tray fastenings:Roofing Bolts, Nuts and Washers page 23
Finishes See page 20.
cable tray systemsancillary items and standard fastenings
23
cable
tra
y s
yst
ems
Fishplates
F/-
Standard Fastenings
HOT DIP GALVANIZED
M6 x 12 pack 100 RBG0612M6 x 16 pack 100 RBG0616
Roofing Nuts and BoltsELECTRO PLATED ZINC
M6 x 12 pack 200 RB0612M6 x 16 pack 200 RB0616M6 x 20 pack 200 RB0620M6 x 25 pack 200 RB0625M6 x 30 pack 100 RB0630M6 x 40 pack 100 RB0640M6 x 50 pack 100 RB0650
Roofing Nuts and Bolts
Roofing Washers
Threaded Rods
Threaded RodConnectors
Fishplates
See table below
Finish Renovation Materials
Galvafroid Paint 400ml AGALVPAINT
2-Pack Epoxy Paste 1 litre AEPOXYPAINT
FishplatesSupplied singly without fastenings.Fishplates are designed for use when joiningXRF cable tray, larger widths of MRF and SRFcable tray and all widths of SS and SH cable traywhich have been cut to length.They fit across the underside of the tray joint toprovide added strength and increase the safeworking load. They also greatly enhance thelateral rigidity of the joint and prevent unevennessin the bed between adjacent trays.
Tray TrayRange Width RefMRF 450-900 WF/-SRF 450-900 WF/-SS 50-300 F/-
450-900 WF/-SH 100-300 F/-
450-600 WF/-XRF* 225 F/-
300 MF/-450-600 WF/-
Fishplate to Tray fastenings:Roofing Bolts, Nuts and Washers page 23
WF/-
*Fishplates for XRF trayare only required whencable loading is in excessof 50% of maximum safeworking load.
MF/-
Threaded Rods - maximum load forconnector
Rod Ref Size SWL, kgf
TR06 M6 91TR08 M8 165TR10 M10 262TR12 M12 381
Roofing WashersHOT DIP GALVANIZED
M6 pack 500 RWG06
Threaded RodsELECTRO PLATED ZINC
M6 x 3m single TR06M8 x 3m single TR08M10 x 3m single TR10M12 x 3m single TR12
Threaded Rod ConnectorsELECTRO PLATED ZINC
M6 x 3m single RC06M8 x 3m single RC08M10 x 3m single RC10M12 x 3m single RC12
STAINLESS STEEL
M6 x 12 pack 100 RB0612/SSM6 x 16 pack 100 RB0616/SSM6 x 20 pack 100 RB0620/SS
STAINLESS STEEL
M6 x 3m single TR06/SSM8 x 3m single TR08/SSM10 x 3m single TR10/SSM12 x 3m single TR12/SS
Ancillary Items
cable tray systemsancillary items and standard fastenings
Electro Plated Zinc
Coach Bolts
Coach BoltsHIGH GRADE STEEL WITH DACROMET FINISH
M6 x 12 pack 100 QBF
Use with MRQBC/- and SRQBC/- (for tray widths300mm and above) and for connecting all MRFand SRF accessories.
Hot Dip Galvanized
The loads shown on all graphs are the safe recommended maximum loads that can be
applied and must include wind, snow and any other external forces in addition to the
cable load. For further details see the Legrand Engineering Manual.
The graphs show the maximum load for Tray installed at a support spacing within its
recommended range.
When the graph line is above the intersection of the required load and span lines, the
support equipment is suitable for use within those load and span conditions.
unacceptable
acceptable
Example
Return Flange Trays
Single Flange Trays
1.0 1.5 2.00
Span, m
Max
imu
m S
afe
Wo
rkin
g L
oad
, kg
/m
50
100
200
250
150
1.5 2.0 2.50
Span, m
Max
imu
m S
afe
Wo
rkin
g L
oad
, kg
/m
150
300
600150
50
100
200
250
2.0 2.5 3.0Span, m
Max
imu
m S
afe
Wo
rkin
g L
oad
, kg
/m150
300
600
150
50
100
200
250
0.5 1.0 1.50
50
100
150
200
Span, m
Max
imu
m S
afe
Wo
rkin
g L
oad
, kg
/m
150
300
600
250
1.5 2.0 2.50
50
100
150
200
Span, m
Max
imu
m S
afe
Wo
rkin
g L
oad
, kg
/m
150
300
600
250
150
600
300
On wider MRF, SRF and XRF trays themaximum safe working load can beincreased by fitting an appropriatefishplate across the underside of eachtray-to-tray joint.
On XRF trays the graph shows themaximum safe working load when afishplate is fitted across the underside ofeach tray-to-tray joint. Typical cable loadswhich are normally 50% of the maximumwould not require a fishplate.
SH
MRF
SRF
XRF
SS
* SRFL/600/- tested with fishplates.
cable tray systemsloading graphs
24
Swif
ts
MRF, SRF, SS, SH, XRF
Hot dip galvanized after manufactureAn excellent, economical protective finish used on support systems in many industrial andcommercial applications.
The galvanized coating is applied as a final manufacturing process by immersing a steelcomponent (after various pre-treatments) in a large bath of molten zinc; the zinc forms analloy with this the steel substrate and protects the steel from corrosion.
BS EN ISO 1416 provides the specification for a hot dip galvanized coating.
Pre-Galvanized steelA zinc coating can be economically applied to steel sheet immediately after itsmanufacture; the result, pre-galvanized steel is an attractive, bright material which issuitable for non-arduous environments.
BS EN 10142 and 10143 provides the specifications for pre-galvanized steel; within thisstandard the Z275 coating classification is normally used for services support equipment.
Deep galvanized Corten A steelA Deep Galvanized finish has all of the characteristics of hot dip galvanizing but with amuch thicker coating of zinc. This gives 2-3 times the life of the standard hot dip galvanizedfinish.
Although the appropriate British Standard for Deep Galvanizing is BS EN ISO 1416 (thesame as for hot dip galvanizing after manufacture) the process requires the use of steelcontaining a slightly higher proportion of silicon; Corten 'A' steel is the usual choice.
Stainless steelFor all practical purposes stainless steel serces supports can be regarded as maintenancefree and suffering no corrosion.
The fire resistance of stainless steel is particularly noteworthy; tests have demonstratedthat stainless steel cable supports can be expected to maintain their integrity forconsiderable periods even when exposed to direct flame temperatures exceeding 1,000°C.
Stainless steel is also used where hygiene is a major consideration.
Many grades of stainless steel are available but the one generally used in aggressivemarine environments is BS EN 10088 Grade 1-4401 (equivalent to 316S31, BS 1449: Part 2).This grade has improved corrosion resistance (particularly in the presence of chlorides) andhigh temperature strength. It is much used in the chloride-laden marine conditions whichexist on offshore installations and in coastal regions.
For less aggressive environments BS EN 10088 Grade 1-4301 (equivalent to 304,BS 1449: Part 2) is the normal grade. This grade is called for when the reason for usingstainless steel is aesthetic and commonly used in the dairy and food industries. Finalfinishes with mechanical brushing or polishing are used to provide a good looking androbust surface finish.
Plastic coatedLegrand offer a number of alternative coated finishes to customer's specification.
Details of those which are available for each product range are given in this catalogue andin relevant Data Sheets in the Legrand Engineering Manual.
FINISH Tray Supports Ancillarieslengths
Hot dip galvanized after manufacture ✔ ✔ ✔
Pre-Galvanized steel ✔ ✘ ✘
Deep galvanized Corten A steel ✔ ✔ ✔
Stainless steel ✔ ✔ ✔
Plastic coated ✔ ✔ ✔
More detailed information on finishes is given in the Legrand Engineering Manual.
25
cable
tra
y s
yst
ems
cable tray systemsfinishes