CATALOGUE OF MATERIALS
About the corporation12-3
TechnoNICOL construction systems24-8
Stone wool413-30
Extruded cellular polystyrene531-34
Bitumen and bitumen-polymer materials635-62
Mastics, sealants, primers763-68
Components and equipment
Accessories for flat roofings
Breathable and vapor control membranes
869-73
Polymer membranes39-12
ABOUT US
About the corporation12
TechnoNICOL is the largest producer and supplier of roofing, waterproofing and heat-insulating materials in Europe. The Corporation was founded in 1993. Today it has 34 factories, its own distribution network and representative offices in 35 countries. In 2008 TechnoNICOL’s turnover exceeded RUB 38 billion.
TechnoNICOL aims to create effective materials and solutions so as to protect the environment and human health. Over 80 million people all over the world live and work in buildings that were built with TechnoNICOL materials.
TechnoNICOL figures
911162534351403005 50030 000180 000510 0001 250 0008 000 00016 000 000830 000 000
Representative offices abroad
Product specializations
Years in market
Share of exports, %
Factories
Countries TechnoNICOL operates in
Sales offices
Authorized dealers
Highly skilled specialists
Production capacity for mastics, tons/year
Facilities built with TechnoNICOL products
Production capacity for stone wool, tons/year
Production capacity for extruded cellular polystyrene, m3/year
Production capacity for polymeric membranes, m2/year
Production capacity for flexible roofing tiles, m2/year
Production capacity for bitumen and bitumen-polymer materials, m2/year
About the corporation 1 3
History of TechnoNICOL
TechnoNICOL was founded. Its first office was opened in Moscow.
Production of roll roofing and waterproofing materials was launched. Vyborg Ruberoid Plant joins TechnoNICOL.
TechnoNICOL develops its own distribution network. The first regional sales office was opened in St. Petersburg.
Kroma Plant (Rybinsk) joins TechnoNICOL.
Reconstruction of the TechnoNICOL plant in Vyborg, resulting in the launch of production of bitumen-polymer materials. They were previously unavailable in the mass construction market of the Russian Federation and the CIS.
The first sales office was opened in Ukraine.
Commissioning of the Technoflex Plant in Ryazan – the most modern Russian producer of bitumen-polymer roll roofing and waterproofing materials.
Minvody-Krovlia Plant (city of Mineralniye Vody) and Tekhnokrom Plant (city of Novou-lianovsk) joined TechnoNICOL. Five more regional sales offices were opened.
The first foreign plant (Gargzdu MIDA, Lithuania) joins the Corporation. TechnoNICOL’s dis-tribution network expands rapidly, and the number of regional sales offices reaches 35 by the end of the year. Intensive development of the company continued through incorporation of factories and sales network into TechnoNICOL Corporation.
TechnoNICOL enters the pitched roof market. A new product – TechnoNICOL flexible roof-ing tiles – was designed and launched. The corporation’s output exceeds 100 000 000 m2 per year, and TechnoNICOL becomes one of the five largest European producers of bituminous waterproofing and roofing materials.
Commissioning of TechnoTOP Plant (Voskresensk, Moscow Region). AKSI Plant (Cheliabinsk), one of the largest producers of mineral fiber heat insulation, joins the Corporation. The first TECHNO-branded insulation materials were produced.
The number of the Corporation’s sales offices exceeds 80. The corporation has branches in all the CIS countries. The first sales office was opened in Warsaw (Poland). NKRZ Plant (Nizhny Novgorod), a producer of modern bonded materials, joins the corporation.
For the first time ever in Russia, production of composite roofing tiles started at Luxard Plant in Voskresensk, Moscow Region. At year-end, TechnoNICOL became the largest producer of roofing membranes in Europe. The first bitumen and bitumen-polymer plant was commis-sioned in Ukraine (Dneprodzerzhinsk). The largest SHINGLAS® flexible roofing tiles plant in Russia was commissioned in Ryazan as a joint venture in cooperation with Chova Company (Spain).
A second TECHNO stone wool production plant was commissioned in Ryazan. Upon commis-sioning, TechnoNICOL Corporation became one of the top three Russian/European leaders in the heat insulation market.
Two extruded cellular polystyrene plants were commissioned (total capacity: 600 000 m3 per year). A mineral wool plant (capacity: 60 000 tons per year) and a roofing materials plant in Yurga (Western Siberia) were commissioned.
A LOGICROOF PVC membranes plant, the pioneer in Russia, was commissioned in Ryazan. New stone wool production lines were launched in Ryazan, Yurga, Cherkassy and Zainsk, new extruded cellular polystyrene lines in Ryazan, Ulianovsk, Mineralniye Vody, Yurga and Dne-prodzerzhinsk. Several plants in Ukraine, as well as the Bitumat Plant (Czech Republic), joined the corporation.
1993
1994
1995 1996
1997
1998 1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
TechnoNICOL construction systems24
TECHNONICOLROOFING SYSTEMS
LOGICROOF V-RP polymeric membrane
TECHNOROOF V 60
TECHNOROOF N 30
TechnoNICOL vapor-proof film for flat roofing
Bearing base — shaped sheet
TN-CLASSICClassic polymer membrane roofing on a shaped sheet base
TN-SMARTRoofing with a composite insulant and a polymer membrane
LOGICROOF V-RP polymeric membrane
Separating layer (fiberglass mat), 100g/m2
TECHNOPLEX 30-250
TECHNOROOF N 30
TechnoNICOL vapor-proof film for flat roofing
Bearing base — shaped sheet
Technoelast EKP
Uniflex EPV VENT
TECHNONICOL No. 01 bitumen primer
Reinforced cement-and-sand screedClaydite on the slope
TECHNOPLEX 30-250
Bikroelast TPP
Leveling screed
Bearing base — reinforced concrete
TN-TRADITIONAL Combined roofing on reinforced concrete base
TechnoNICOL construction systems 2 5
TN-CLIMATE All-season solution with bitumen-polymer materials
Technoelast EKP
Uniflex EPV VENT
TECHNONICOL No. 01 bitumen primer
Assembled screed
TECHNOPLEX 30-250
TECHNOPLEX KLIN V-shaped insulation
TechnoNICOL vapor-proof film
Bearing base — reinforced concrete
TN-BALLAST CLASSIC Polymer membrane ballast roofing
Ballast: gravel or ballast stone, fraction 20-40
Needled geotextile, 300g/m2
LOGICROOF V-GR Separating layer (fiberglass mat), 100g/m2
TECHNOPLEX 30-250
TechnoNICOL vapor-proof film
Cement-and-sand screed
Slope-forming claydite layer
Bearing base — reinforced concrete
TN-STEP Roofing for sidewalk pavement
Paving slabs
Cement-and-sand mixture
Thermobonded geotextile TechnoNICOL
A layer of gravel, fraction 5-20, 40mm thick min.
TechnoNICOL thermobonded geotextile
TECHNOPLEX 30-250
Needled geotextile TechnoNICOL, 300g/m2
Technoelast EPP (2 layers)
Reinforced cement-and-sand screed
TECHNONICOL No. 01 bitumen primer
Slope-forming claydite layer
Bearing base — reinforced concrete
TechnoNICOL construction systems26
TECHNONICOL FACADE SYSTEMSFacade systems for civil and industrial construction
TN-TECHNO system
Load bearing/self supporting part of the walls(bricks, light blocks with min. density 800kg/m3,
solid-cast reinforced concrete)
TECHNOVENT STANDART, TECHNOVENT OPTIMA, TECHNOVENT PROF, TECHNOVENT DOUBLE
Techno-System load bearing subsystem
TechnoNICOL dish facade dowel
Techno System facing panels
Note: It is recommended to cover the insulation with TechnoNICOL super-diffusion film in the boundary zone.
TN-DECOR mineral
Outer wall
TechnoNICOL fiberglass fabric grid
Quartz prime coat
Hardening prime coat
TechnoNICOL adhesive for heat insulation slabs
TECHNOFAS, TECHNOFAS L, TECHNOFAS DOUBLE
TechnoNICOL facade dowel
TechnoNICOL base reinforcing layer(TechnoNICOL adhesive for heat insulation slabs)
TechnoNICOL decoration plaster
Facade paint (where necessary)
TN-BRICK building
Load bearing flooring with a system of thermal inserts
Waterproofing layer
Load bearing/self-supporting part of the walls(bricks, light blocks with min. density 800gr/m3,
solid-cast reinforced concrete)
TECHNOBLOCK
Ventilated gap (with supply and exhaust holes)
TechnoNICOL ties with gap fixing pins
Facing brick
TechnoNICOL construction systems 2 7
TECHNONICOL FOUNDATION SYSTEMSTN- BASE wallSlurry wall insulation system
Soil
Slurry wall
Squared up surface
Protection (underlay) layer (TechnoNICOL geotextile)
TechnoNICOL rondel (fastening element)
LOGICROOF T-SL polymeric membrane
TechnoNICOL waterproofing seal
Injection nozzle
Protection layer (TechnoNICOL geotextile)
TechnoNICOL polyethylene film
Injection tubes to the interior
Internal reinforced structure
TN-BASE proInsulation system for foundations with high ground water level. Installation depth down to 3m.
Reinforced concrete wall
Foundation slab
Cement grout sloping board, min. 50/50mm
TECHNONICOL No. 01 bitumen primer
Technoelast EPP
TECHNOPLEX STANDART 30-250 extruded cellular polystyrene
Backfill
Concrete primer
Protection cement-and-sand screed
Ballast stone
Foundation soil
TechnoNICOL construction systems28
TN-BASE drainInsulation system for foundations with low ground water level. Installation depth down to 3m.
TECHNOPLEX 30-250 STANDART heat insulation
TECHNONICOL No. 01 bitumen primer
PLANTER geo corrugated membrane
TECHNOELASTMOST B waterproofing layeron vertical and horizontal surfaces
TECHNOELASTMOST B extra waterproofing
Backfill
Reinforced concrete floor slab
PLANTER Standard corrugated membrane
Drain pipe
Sand layer
Compacted ballast stone
Foundation soil
POLYMER MEMBRANES
TECHNICAL SUPPORT AND INFORMATION ABOUT SALES OFFICES:Phone: +7 (495) 9255775, 8-800-200-05-65; Fax: +7 (495) 9258155
E-mail: [email protected] www.teplo.ru
Polymer membranes310
PVC-membrane LOGICROOFDescription:PVC (plasticized polyvinylchloride) membrane LOGICROOF is a water-proofing roofing material.
Field of application:Polymeric membranes LOGICROOF can be used for any type of roofing system: ballast, with mechanical fixation or glued, are compatible with the roofs of any construction. Moreover, the membranes are suitable for the installation of new roofs as well as for repairs of used roof coverings. Polymeric membranes LOGICROOF can be installed on a surface fast and easily – it is welded by hot air, using automatic equipment. The mounting of the material practically does not depend on weather conditions.
Type of material Field of application
1. LOGICROOF V-RP®Thickness – 1,2-2,0 mm;
PVC-membrane, reinforced with polyester grid that provides a larger rupturestrength and absence of material shrinkage. Material used as waterproofing layeron roofs with mechanical fixation.
2. LOGICROOF V-SR®Thickness – 1,5 mm;
No reinforcement PVC-membrane. Used for production supplementary elements:joining with base roofing cover.
3. LOGICROOF V-GR®Thickness – 1,5-2,0 mm;
PVC-membrane, reinforced with glass fiber. Material used as waterproofing layerfor ballast roofing system. Material has a ruggedness puncture resistance.
4. LOGICROOF T-SL®Thickness – 1,5-3,0 mm;
Tunnel PVC-membrane ECOPLAST T-SL is an no reinforcement material,microorganisms and roots resistant. This material has a signal layer of yellowcolor, allowing fast detection of waterproof covering damages.
Basic technical characteristic:LOGICROOF V-RP LOGICROOF V-SR LOGICROOF V-GR LOGICROOF T-SL
PVC PVC PVC PVCBase
polyester no reinforcement glassfiber no reinforcementReinforcement
1,2-2,0 1,5 1,5-2,0 1,5-3,0Thickness
20 15 15 15Tensile strength, MPa
90 200 90 200Elongation of break, %
0,3 0,1 0,3 0,1Water absorption, %
-45 -45 -45 -45Low temperatureflexibility on 5 mm, °С
waterproofStatic bursting strength,250Н х 24 h
G1, G2 G4 G4 G3Combustibility group
Polymer membranes 3 11
PVC-membrane ECOPLASTDescription:PVC (plasticized polyvinylchloride) membrane ECOPLAST is a water-proofing roofing material.
Field of application:Polymeric membranes ECOPLAST can be used for any type of roofing system: ballast, with mechanical fixation or glued, are compatible with the roofs of any construction. Moreover, the membranes are suitable for the installation of new roofs as well as for repairs of used roof coverings. Polymeric membranes ECOPLAST can be installed on a surface fast and easily – it is welded by hot air, using automatic equipment. The mounting of the material practically does not depend on weather conditions.
Type of material Field of application
1. ECOPLAST V-RP®Thickness – 1,2-2,0 mm;
PVC-membrane, reinforced with polyester grid that provides a larger rupturestrength and absence of material shrinkage. Material used as waterproofinglayer on roofs with mechanical fixation.
2. ECOPLAST V-SR®Thickness – 1,5 mm;
No reinforcement PVC-membrane. Used for production supplementaryelements: joining with base roofing cover.
3. ECOPLAST V-GR®Thickness – 1,5 mm;
PVC-membrane, reinforced with glass fiber. Material used as waterproofinglayer for ballast roofing system. Material has a ruggedness puncture resistance.
4. ECOPLAST T-SL®Thickness – 1,5-2,0 mm;
Tunnel PVC-membrane ECOPLAST T-SL is an no reinforcement material,microorganisms and roots resistant. This material has a signal layer of yellowcolor, allowing fast detection of waterproof covering damages.
Basic technical characteristic:ECOPLAST V-RP ECOPLAST V-SR ECOPLAST V-GR ECOPLAST T-SL
PVC PVC PVC PVCBase
polyester no reinforcement glassfiber no reinforcementReinforcement
1,2-2,0 1,5 1,5 1,5-2,0Thickness
19 14 14 14Tensile strength, MPa
60 200 90 200Elongation of break, %
0,3 0,1 0,5 0,2Water absorption, %
-40 -40 -30 -30Low temperatureflexibility on 5 mm, °С
waterproofStatic bursting strength,250Н х 24 h
G1, G2 G4 G4 G4Combustibility group
MEMBRANE FROM HIGHDENSITY POLYETHYLENE – HDPE “PLANTER”
Descriptions of material:Knobbed membrane Planter made from high density polyethylene.
Field of application:General functions of PLANTER – waterproofing protection and organi-zation of drainage. Planter is notable for high mechanical strength and its resistance to chemical aggressive environment, is not subjected to the destroyable influence of mould and bacteria, is resistant to root sprout-ing of trees and to the UF influence.
Physical-mechanical characteristics
Description
Weight 1m2, kg
One layer sheet from high densitypolyethylene withround knobs 20mmhigh with perfora-
tion
14
-30 +80
180 (~18)
12
PLANTER-life
One layer sheet from high densitypolyethylene withround knobs 20mm
high
14
-30 +80
180 (~18)
12
PLANTER-gigant
Three layersmembrane – sheetfrom high densitypolyethylene withround knobs 8mmhigh, mechanicalthermo bonded
geotextile, protec-tion sheet from
polyethylene
5,5
-30 +80
400 (~40)
3,5
PLANTER-active
Two layers mem-brane – sheet
from high density polyethylene
with round knobs8mm high, me-chanical thermobonded geotextile
5,5
-30 +80
250 (~25)
4,6
PLANTER-geo
One layer sheet from high densitypolyethylene with round knobs 8mm
high
5,5
-30 +80
280 (~28)
-
PLANTER-standard
Compressive strength, kN/m2 (t/m2)
Carrying capacity, l/sec, m2
Air volume between knobs, l/m2
Apply temperature, °C
1,01,00,950,650,6
Type of material Field of application1. PLANTER -standard®High of knobs – 8mm;Compressive strength – 280kN/m2 (28 t/m2)
Protection of bituminous waterproofing of underground constructions during filling the foundation pit up with soil; protection of foundation slab from capillary humidity; drying of moist walls; in exploited roofing.
2. PLANTER -gigant®High of knobs – 20mm;Compressive strength – 180kN/m2 (18 t/m2)
The same application as for Planter-standard; when big water inflow exists; loads distribu-tion in inverse roofing.
3. PLANTER -geo®High of knobs – 8mm;Compressive strength – 250kN/m2 (25 t/m2)
Mounting of drainage layer in roofing and waterproofing.
4. PLANTER -active®High of knobs – 8mm;Compressive strength – 400kN/m2 (40 t/m2)
Protection of (underground) bituminous waterproofing and organization of drainage when distend soils exists and in foundations sunk to a great depth.
5. PLANTER -life®High of knobs – 20mm;Compressive strength – 180kN/m2 (18 t/m2)
In order to keep moisture in “green” roofing.
Polymer membranes312
STONE WOOL TECHNONICOLNON-FLAMMABLE INSULATION
TECHNICAL SUPPORT AND INFORMATION ABOUT SALES OFFICES:Phone: +7 (495) 9255775, 8-800-200-05-65; Fax: +7 (495) 9258155
E-mail: [email protected] www.teplo.ru
Stone wool414
TECHNOLIGHTTECHNOLIGHT – nonflammable, waterre-pellent thermal and sound insulation slabs of mineral wool made from rocks of the basalt group.
Application:TECHNOLIGHT slabs are intended for thermal and sound insulation of residential and indus-trial buildings in which insulation material is not subjected to external load.They are recommended for thermal insulation of horizontal, sloping, and vertical structures, such as ventilated surfaces of sloping roofs, mansards, roof decks, floors with insulation between joists, stud walls and partitions.
DimensionsLength
Width
Thickness
1000, 1200 mm
500, 600 mm
40-200 mm, with a 10 mm step
TECHNOLIGHT slabs are characterized by:• high heat retention properties;
• resistance to high temperatures impact;
• volume and shape stability;
• low water absorption;
• high sound absorption properties;
• resistance to microorganisms and rodents;
• neutrality to concrete and metallic materials;
• ease of installation, cutting and handling - can be easily cut with a knife or saw.
Fire resistanceTECHNOLIGHT slabs are nonflammable mate-rial. They can be used in the temperature range of - 60 to + 200°C. The melting point of the fibers exceeds 1000°C.
Acoustic absorption factorFrequence, Hz
Thickness 50 mm
Thickness 100 mm
0,20
125
0,38
0,48
250
0,68
0,85
500
0,97
0,93
1000
1,00
0,84
2000
0,91
0,70
4000
0,80
Technical specification TU 5762-043-17925162-2006
Physical-mechanical characteristics
TECHNOLIGHTEXTRA
TECHNOLIGHTOPTIMA
TECHNOLIGHTPROF
Density, kg/m3 30 35 40
Compressibility, %, no more 30 30 20
Thermal conductivity
At 10 °С, W/(m *°C), not more than
At 25 °С, W/(m *°C), not more than
Under conditions А, W/(m *°C), not more than
Under conditions B, W/(m *°C), not more than
Vapor permeability, mg/(m*h*Pa), not less than
Humidity by weight, %, not more than
Water absorption by volume, %, not more than
Organic substances content, %, not more than
Flammability, degree Nonflammable Nonflammable Nonflammable
0,036 0,035 0,034
0,039 0,037 0,036
0,046
0,3
1,5
2,5 2,5 2,5
1,5 1,5
0,5 0,5 0,5
0,3 0,3
0,049 0,048 0,043
0,045 0,040
Stone wool 4 15
ROCKLIGHTROCKLIGHT is a light, water repellent, non-flammable thermal and sound insulation slabs of mineral wool on the base of the rocks of basalt group. It is a universe material for the private building.
Application:It is recommended for the usage as an insula-tion aterial for the horizontal, slope and verti-cal constructions such as attics, skeleton walls, walls with sidings, floors, overlapping, parti-tions.
DimensionsLength
Width
Thickness
1000, 1200 mm
500, 600 mm
50 mm
ROCKLIGHT slabs are characterized by• high heat retention properties;
• resistance to high temperatures impact;
• volume and shape stability;
• low water absorption;
• high sound absorption properties;
• resistance to microorganisms and rodents;
• neutrality to concrete and metallic materials;
• ease of installation, cutting and handling - can be easily cut with a knife or saw.
Fire resistanceROCKLIGHT slabs are nonflammable material.They can be used in the temperature range of- 60 to + 200°C. The melting point of the fi-bers exceeds 1000°C.
Technical specification TU 5762-049-17925162-2006
Physical-mechanical characteristicsDensity, kg/m3
Compressibility, %, no more 30
30
Thermal conductivity
At 25 °С, W/(m *°C), not more than
Under conditions А, W/(m *°C), not more than
Under conditions B, W/(m *°C), not more than
Vapor permeability, mg/(m*h*Pa), not less than
Water absorption by volume, %, not more than
Humidity by weight, %, not more than
Organic substances content, %, not more than
Flammability, degree Nonflammable
0,042
2,5
0,5
2,0
0,3
0,051
0,048
Stone wool416
TECHNOBLOCKTECHNOBLOCK – nonflammable, waterre-pellent thermal and sound insulation slabs of mineral wool made from rocks of the basaltgroup.
Application:TECHNOBLOCK – nonflammable, waterre-pellent thermal and sound insulation slabs of mineral wool made from rocks of the basaltgroup.TECHNOBLOCK slabs are intended for thermal and sound insulation of residential and indus-trial buildings in which the insulation material is not subjected to external load. They are rec-ommended for thermal insulation of horizon-tal, sloping, and vertical structures,skeleton-frame residential buildings, and areused as the medium thermal insulation layerin a three-layer cavity walls made from small-size materials.
DimensionsLength
Width
Thickness
1000, 1200 mm
500, 600 mm
30-200 мм, with a 10 mm step
TECHNOBLOCK slabs are characterized by:• high heat retention properties;
• resistance to high temperatures impact;
• volume and shape stability;
• low water absorption;
• high sound absorption properties;
• resistance to microorganisms and rodents;
• neutrality to concrete and metallic materials;
• ease of installation, cutting and handling - can be easily cut with a knife or saw.
Fire resistanceTECHNOBLOCK slabs are nonflammable ma-terial. They can be used in the temperature range of - 60 to + 200°C. The melting point of the fibers exceeds 1000°C.
Technical specification TU 5762-043-17925162-2006
Physical-mechanical characteristics
ТECHNOBLOCKSTANDART
ТECHNOBLOCKOPTIMA
ТECHNOBLOCKPROF
Density, kg/m3 45 55 65
Compressibility, %, no more 10 8 5
Thermal conductivity
At 10 °С, W/(m *°C), not more than
At 25 °С, W/(m *°C), not more than
Under conditions А, W/(m *°C), not more than
Under conditions B, W/(m *°C), not more than
Vapor permeability, mg/(m*h*Pa), not less than
Humidity by weight, %, not more than
Water absorption by volume, %, not more than
Organic substances content, %, not more than
Flammability, degree Nonflammable Nonflammable Nonflammable
0,034 0,034 0,033
0,036 0,036 0,035
0,043
0,3
1,5
2,5 2,5 2,5
1,5 1,5
0,5 0,5 0,5
0,3 0,3
0,046 0,044 0,043
0,041 0,040
Stone wool 4 17
TECHNOVENTTECHNOVENT – nonflammable, waterrepel-lent thermal and sound insulation slabs of mineral wool made from rocks of the basalt group.
Application:Used in residential and industrial construction as a thermal insulation layer in new construc-tion and reconstruction of buildings and struc-tures serving a variety of purposes.TECHNOVENT slabs are intended as a thermal insulation layer in insulation systems with a ventilated air cavity in external walls (venti-lated facades).
DimensionsLength
Width
Thickness
1000, 1200 mm
500, 600 mm
30–200 mm with a 10 mm step
TECHNOVENT slabs are characterized by:• high heat retention properties;
• resistance to high temperatures impact;
• volume and shape stability;
• low water absorption;
• high sound absorption properties;
• resistance to microorganisms and rodents;
• neutrality to concrete and metallic materials;
• ease of installation, cutting and handling - can be easily cut with a knife or saw.
Fire resistanceTECHNOVENT slabs are nonflammable mate-rial. They can be used in the temperature range of - 60 to + 200°C. The melting point of the fibers exceeds 1000°C.
Technical specification TU 5762-043-17925162-2006
Physical-mechanical characteristics
TECHNOVENTSTANDART
TECHNOVENTOPTIMA
TECHNOVENTPROF
Density, kg/m3 80 90 100
Compressibility, %, no more 2 2 2
Thermal conductivity
At 10 °С, W/(m *°C), not more than
At 25 °С, W/(m *°C), not more than
Under conditions А, W/(m *°C), not more than
Under conditions B, W/(m *°C), not more than
Vapor permeability, mg/(m*h*Pa), not less than
Humidity by weight, %, not more than
Water absorption by volume, %, not more than
Organic substances content, %, not more than
Flammability, degree Nonflammable Nonflammable Nonflammable
0,034 0,034 0,034
0,036 0,036 0,036
0,043
0,3
1,5
3,0 3,0 3,0
1,5 1,5
0,5 0,5 0,5
0,3 0,3
0,046 0,044 0,047
0,041 0,044
Compression strength at 10% deformation, kPa, not less than 10 12 15
Layer peel strength, kPa, not less than 3 5 8
Stone wool418
TECHNOFASTECHNOFAS – light, nonflammable, waterre-pellent thermal and sound insulation slabs of mineral wool made from rocks of the basalt group.
Application:TECHNOFAS slabs are indented for applica-tion in residential and industrial construction as thermal insulation in external insulation systems of walls with a protective decorative layer of thin stucco.
DimensionsLength
Width
Thickness
1000, 1200 mm
500, 600 mm
40–150 mm, with a 10 mm step
TECHNOFAS slabs are characterized by:• low thermal conductivity;
• geometrical precision;
• high durability parameters;
• high peel strength;
• resistance to high temperatures;
• 100% resistance to freezing-thawing cycles;
• low water absorption;
• high vapor permeability;
• chemical neutrality to construction materials;
• high sound absorption properties.
Fire resistanceTECHNOFAS slabs are nonflammable material. They can be used in the temperature range of- 60 to + 200°C. The melting point of the fi-bers exceeds 1000°C.
Technical specification TU 5762-043-17925162-2006
Physical-mechanical characteristicsDensity, kg/m3
Thermal conductivity:
0,036
145
At 10 °С, W/(m *°C), not more than
At 25 °С, W/(m *°C), not more than
under conditions A, W/(m *°C), not more than
under conditions B, W/(m *°C), not more than
Compression strength at 10% deformation, kPa, not less than
Layer peel strength, kPa, not less than
Water absorption upon complete immersion by volume, %, not more than
Vapor permeability, mg/(m*h*Pa), not less than
Organic substances content, %, not more than
Humidity by weight, %, not more than 0,5
0,038
0,042
4,5
0,3
1
15
45
0,045
Flammability, degree Nonflammable
Stone wool 4 19
TECHNOSANDWICHTECHNOSANDWICH - nonflammable, water-repellent thermal and sound insulation slabs of mineral wool made from rocks of the gabbro-basalt group.
Application:TECHNOSANDWICH BETON slabs are used as the thermal insulation lay in the 3-layer con-crete and ferroconcrete wall panels.TECHNOSANDWICH C slabs are used as thethermal insulation layer in 3-layer wall sand-wich panels with metallic boarding.TECHNOSANDWICH K panels are used as ther-mal insulation layer in 3-layer roofing sand-wich panels with metallic boarding.
DimensionsLength
Width
Thickness
1200, 2400 mm
600, 627, 800, 1200 mm
102 (122) mm
TECHNOSANDWICH slabs are characterized by:• low thermal conductivity;
• geometrical precision;
• high durability parameters;
• high peel strength;
• resistance to high temperatures;
• 100% resistance to freezing-thawing cycles;
• low water absorption;
• high vapor permeability;
• chemical neutrality to construction materials;
• high sound absorption properties.
Fire resistanceTECHNOSANDWICH slabs are nonflammable material. They can be used in the temperaturerange of - 60 to + 200°C. The melting point of the fibers exceeds 1000°C.
Technical specification TU 5762-043-17925162-2006
Physical-mechanical characteristics
TECHNOSANDWICHBETON
TECHNOSANDWICH C TECHNOSANDWICH K
Density, kg/m3 100 105 140
Thermal conductivity at 25°C, W/(m *°C), not more than 0,036 0,040 0,042
Layer peel strength, kPa, not less than
Compression strength, кPa
Shearing strength, кPa, not less
Water absorption by volume, %, not more than
Water absorption upon partial immersion by volume, %, not more than
Vapor permeability, mg/(m*h*Pa), not less than
Organic substances content, %, not more than
Humidity by weight, %, not more than
Flammability, degree
- 60* 100*
- 50* 75*
1,5
0,3
0,5
Nonflammable Nonflammable Nonflammable
0,5 0,5
4,5 4,5 4,5
0,3 0,3
10 10 10
1,5 1,5
Thermal conductivity at 10°C, W/(m *°C), not more than 0,034 0,038 0,040
Compression strength at 10% deformation, kPa, not less than 20 - -
- 100* 100*
* The slabs are cutting into the stripes (lamellas), the samples are turned for 90 ° around the long axes
Stone wool420
TECHNOROOF NTECHNOROOF N – nonflammable, waterre-pellent thermal and sound insulation slabs of mineral wool made from rocks of the basalt group.
Application:Used in residential and industrial construc-tion as a thermal insulation layer in new con-struction and reconstruction of buildings and structures serving a variety of purposes. TECH-NOROOF N slabs are intended for application as the main thermal insulation layer in coats made from ferroconcrete or metallic decking with roofing of rolled or built-up roofing ma-terials. Recommended for application in com-bination with TECHNOROOF V slabs.
DimensionsLength
Width
Thickness
1000, 1200 mm
500, 600 mm
50–200 mm, with a 10 mm step
TECHNOROOF N slabs are characterized by:• high heat-retention properties;
• resistance to high temperatures;
• high resistance to deformation and mechanical loads;
• volume and shape stability;
• low water absorption;
• high sound absorption properties;
• resistance to microorganisms and rodents;
• neutrality to concrete and metallic materials;
• ease of installation, cutting and handling - can be easily cut with a knife or saw.
Fire resistanceTECHNOROOF N slabs are nonflammable ma-terial. They can be used in the temperature range of - 60 to + 200°C. The melting point of the fibers exceeds 1000°C.
Technical specification TU 5762-043-17925162-2006
Physical-mechanical characteristics
Density, kg/m3
Compression strength at 10% deformation, kPa, not less than
Thermal conductivity:
at 10°C, W/(m *°C), not more than
at 25°C, W/(m *°C), not more than
under conditions A, W/(m *°C), not more than
under conditions B, W/(m *°C), not more than
Vapor permeability, mg/(m*h*Pa), not less than
Humidity by weight, %, not more than
Water absorption by volume, %, not more than
Organic substances content, %, not more than
TECHNOROOF N25
25
95
4,5
0,036
0,038
0,048
0,5
1,5
0,3
0,045
TECHNOROOF N30
30
100
4,5
0,034
0,036
0,044
0,5
1,5
0,3
0,041
TECHNOROOF N35TECHNOROOF N40
35 40
110 120
4,5 4,5
0,035 0,037
0,037 0,039
0,047 0,045
0,5 0,5
1,5 1,5
0,3 0,3
0,044 0,042
Flammability, degree Nonflammable Nonflammable Nonflammable Nonflammable
Stone wool 4 21
TECHNOROOFTECHNOROOF – nonflammable, waterrepel-lent thermal and sound insulation slabs of mineral wool made from rocks of the basalt group.
Application:Used in residential and industrial constructionas a thermal insulation layer in new construc-tion and reconstruction of buildings and struc-tures serving a variety of purposes. TECHNO-ROOF slabs are intended for application as the main thermal insulation layer in coats made from ferroconcrete or metallic decking with roofing of all types, including roofing withoutprotective coatings.
DimensionsLength
Width
Thickness
1200, 2400 mm
500, 600 mm
50-110 mm, with a 10 mm step
Fire resistanceTECHNOROOF slabs are nonflammable mate-rial. They can be used in the temperature range of - 60 to + 200°C. The melting point of the fibers exceeds 1000°C.
TECHNOROOF slabs are characterized by:• high heat-retention properties;
• resistance to high temperatures;
• high resistance to deformation and mechanical loads;
• volume and shape stability;
• low water absorption;
• high sound absorption properties;
• resistance to microorganisms and rodents;
• neutrality to concrete and metallic materials;
• ease of installation, cutting and handling - can be easily cut with a knife or saw.
Technical specification TU 5762-043-17925162-2006
Physical-mechanical characteristicsTECHNOROOF 45
Density, kg/m3
Compression strength at 10% deformation, kPa, not less than
45
140
Layer peel strength, kPa, not less than
Thermal conductivity:
than
At 25°C, W/(m *°C), not more than
Under conditions A, W/(m *°C), not more than
Under conditions B, W/(m *°C), not more than
Vapor permeability, mg/(m*h*Pa), not less than
Humidity by weight, %, not more than
Water absorption by volume, %, not more than
Organic substances content, %, not more than 4,5
0,036
0,038
0,047
0,5
1,5
0,3
0,044
TECHNOROOF 50
50
160
4,5
0,036
0,038
0,046
0,5
1,5
0,3
0,043
TECHNOROOF 60
60
170
4,5
0,037
0,039
0,049
0,5
1,5
0,3
0,046
TECHNOROOF 70
70
180
4,5
0,038
0,040
0,047
0,5
1,5
0,3
0,043
Flammability, degree Nonflammable Nonflammable Nonflammable Nonflammable
10 10 12 12
Stone wool422
TECHNOROOF VTECHNOROOF V – Nonflammable, waterre-pellent thermal and sound insulation slabs of mineral wool made from rocks of the basalt group.
Application:Used in residential and industrial constructionas a thermal insulation layer in new construc-tion and reconstruction of buildings and struc-tures serving a variety of purposes. TECHNO-ROOF V slabs are intended for application as the main thermal insulation layer in coats made from ferroconcrete or metallic decking with roofing of rolled or built-up roofing ma-terials.Recommended for application in combinationwith TECHNOROOF V slabs.
DimensionsLength
Width
Thickness
1000, 1200 mm
500, 600 mm
30-50 mm, with a 10 mm step
TECHNOROOF V slabs are characterized by:• high heat-retention properties;
• resistance to high temperatures;
• high resistance to deformation and mechanical loads;
• volume and shape stability;
• low water absorption;
• high sound absorption properties;
• resistance to microorganisms and rodents;
• neutrality to concrete and metallic materials;
• ease of installation, cutting and handling - can be easily cut with a knife or saw.
Fire resistanceTECHNOROOF V slabs are nonflammable ma-terial. They can be used in the temperature range of - 60 to + 200°C. The melting point of the fibers exceeds 1000°C.
Technical specification TU 5762-043-17925162-2006
Physical-mechanical characteristics
Density, kg/m3
Compression strength at 10% deformation, kPa, not less than
Layer peel strength, kPa, not less than
Thermal conductivity:
than
At 25°C, W/(m *°C), not more than
Under conditions A, W/(m *°C), not more than
Under conditions B, W/(m *°C), not more than
Vapor permeability, mg/(m*h*Pa), not less than
Humidity by weight, %, not more than
Water absorption by volume, %, not more than
Organic substances content, %, not more than
TECHNOROOF V50
50
170
4,5
0,036
0,038
0,046
0,5
1,5
0,3
0,043
TECHNOROOF V60
60
180
4,5
0,037
0,038
0,046
0,5
1,5
0,3
0,043
TECHNOROOF V70
70
190
4,5
0,038
0,040
0,048
0,5
1,5
0,3
0,045
Flammability, degree Nonflammable Nonflammable Nonflammable
15 15 15
Stone wool 4 23
TECHNOFAS LTECHNOFAS L – bars cut from nonflammablewater-repellent thermal and sound insulationslabs on the synthetic binder made from min-eral wool on the basis of rocks of the basalt group. The fibers in a lamel are situated per-pendicular to the isolated surface.
Application:TECHNOFAS L slabs are intended for applica-tion as thermal insulation in the external part of the fasade systems. Furthermore, the prod-uct serves as a basis for application of the pro-tective and decorative layers of plaster.The product is also applied for insulation of those parts of walls that have a curved or “broken” surface (for example, bay-windows, pilasters etc).
DimensionsLength
Width
Thickness
1000, 1200 mm
200 mm
40–240 mm, with a 10 mm step
Fire resistanceTECHNOFAS L slabs are made from a non-flammable material. They can be used in the temperature range of -60°С to +200°С. The melting point of the fibers exceeds 1000°С.
TECHNOROOF slabs are characterized by:• flexibility;
• ease of installation;
• low thermal conductivity;
• geometrical precision;
• high durability parameters;
• high peel strength;
• resistance to high temperatures;
• 100% resistance to freezing-thawing cycles;
• law water absorption;
• high vapor permeability;
• chemical neutrality to construction materials;
• high sound absorption properties.
Technical specification TU 5762-043-17925162-2006
Physical-mechanical characteristicsDensity, kg/m3
At 10°С, W/(m*°С], not more than
At 25°С, W/(m*°С], not more than
Under conditions А, W/(M*°С], not more than
Under conditions B , W/(m*°С], not more than
Compression resistance at 10% deformation, kPa, not less than
Breaking point of layer peel, not less than
Water absorption by volume, %, not more than
Vapor permeability, mg/(m*h*Pa), not less than
Organic substance content, %, not more than
Humidity by weight, %, not more than
80
0,5
0,045
0,048
80
0,3
4
1
50
Flammability, degree Nonflammable
0,037
Thermal Conductivity:
0,040
Stone wool424
ROOFING WEDGEROOFING WEDGE (fillet) is applied to make an incline of the parapet ina flat roofing. It is designed to provide a smooth passage of the hydro isolation material from the horizontal roofing surface to the vertical par-apet surface. It is installed along the perimeter of the roofing.
ApplicationROOF SLOPING SLABS are used to create a slope enabling to remove water from the roof-ing system to the water release points.A slope is a roof pitch inclination angle to the horizon. Without good slopes, assuring an unconstrained flow of water, a safe roofing system can not exist. To create a roof sloping the slabs are installed along the perimeter with the inclination to the water outlets. In case of a double thermal insulation system the instal-lation is made on the first (lower) layer of the material.
Installation• Mechanical installation;• Attachment on the bitumen mastic;• Attachment on the bilateral bitumen and polymeric selfadhesive sticker.
ROOFING WEDGE 100Density, kg/m3
Compression resistance at 10% deformation, kPa, not less than
Angle of cutting, %
180
60
45
Area of cut , m2 0,005
Volume of 1 piece, m3 0,006
Weight of 1 piece, kg 1,08
Advantages:• Reduction of work execution terms• Convenience of TechnoNICOL systems installation
ROOF SLOPING SLABS
DimensionsLength
Width
Thickness (in a narrow / wide part]
1200 mm
600 mm
10/30, 15/65, 40/60 mm
Physical-mechanical characteristicsThickness , mm
Compression resistance at 10%deformation, kPa, not less than
40/60
180
60
Inclination angle, % 3,3
Angle of cut, m2 0,03
Volume of 1 piece, m3 0,036
Density, kg/m3
Weight, kg 6,48
15/65
180
60
8,3
0,024
0,0288
5,184
10/30
180
60
3,3
0,012
0,0144
2,592
Stone wool 4 25
DOUBLE DENSITY SLABSNon-flammable waterproofed heat and acoustic insulation slabs, made of stone wool, on the basis of gabbroic basalt rocks.The slab structure is composite and combines hard (external) and soft lower (internal) lay-ers. Because of layered structure, slabs weigh less and are easy to install. The upper (hard) layer is marked.
Application:TECHNOVENT DOUBLE LAYER slabs are used as one-layer heat insulation of walls. In dis-tinction to the two-layer solution, you do not need to mount the slab’s lower layer, there-fore it requires fewer fittings, can be assem-bled faster and the entire system is cheaper.
TECHNOFAS DOUBLE LAYER slabs are used to insulate, from heat or cold, external sur-face of buildings with thin plaster layer. The slabs insulate heat and are base for the plaster layer. TECHNOFAS DOUBLE LAYER slabs are used for one-layer insulation.
TECHNOROOF DOUBLE LAYER slabs are used to insulate, from heat or cold, roofing struc-tures. The slabs are used under waterproof membrane roofing of roll and mastic materi-als, also without cement-and-sand screeds.
DimensionsLength
Width
Thickness of upper layer:
1000, 1200 mm
600 mm
40–240 mm, with a 10 mm step
Thickness of lower layer:
TECHNOVENT DOUBLE LAYER: 50-170 mm with 10 mm spacing
TECHNOFAS DOUBLE LAYER: 40-170 mm with 10 mm spacing
TECHNOROOF DOUBLE LAYER: 60-200 mm with 10 mm spacing
Technical specification TU 5762-00274182-1-81-2007
Physical-mechanical characteristics
Density of upper layer (kg/m3)
Density of upper layer (kg/m3)
Min. compressibility at 10% deformation (kPa)
Tear strength of layers at 10% deformation (kPa)
Max. thermal conductivity at10 0С, W/(m *°С), no more than
Max. thermal conductivity at10 0С, W/(m *°С), no more than
Max. thermal conductivity under conditions А, W/(m*°С)
Max. thermal conductivity under conditions B, W/(m*°С)
Max. humidity by weight (%)
Max. water absorption by volume (%)
Max. organic substances content (%)
Flammability degree
TECHNOVENT DOUBLE LAYER
45
90
Nonflammable
-
0,033
0,036
0,046
1,5
4,0
0,5
0,043
TECHNOFASDOUBLE LAYER
95
180
Nonflammable
-
0,036
0,037
0,047
1
4,5
0,5
0,044
TECHNOROOFDOUBLE LAYER
110
180
Nonflammable
40
0,036
0,038
0,045
1,5
4,5
0,5
0,042
4 15 -
Stone wool426
FIREPROOF SLAB FOR THE IN-SULATION OF CONCRETE CON-STRUCTIONS TECHNONICOLProduct description:Fireproof slab for the insulation of concrete constructions TECHNONICOL - nonflam-mable, thermal and sound insulation stitched mat from mineral wool on the base of basalt rocks.It can be produced with the lining of aluminum foil or glass cloth.
Application:In the civil and industrial engineering for new projects and reconstructions of the buildings with different functions as a thermal insula-tion and fire protection material for ferrocon-crete structures.For the fire protection of ferroconcrete cross-overs in the industrial and civil engineering. Degree of fire resistance is 240 minutes with the thickness of fireproof slab 60 mm.
Technical specification TU 5762-004-74182181-2008
Physical-mechanical characteristicsDensity, kg/m3
l�10
l�25
l�A l�B
100
0,044
0,047
0,034
Thermal conductivity, W/mК:
20Compression strength at 10% deformation, kPa
0,036
DimensionsLength
Width
Thickness
1200 mm
600, 1200 mm
60-200 mm
Stone wool 4 27
CYLINDER TECHNONICOLProduct description:Cylinder TECHNONICOL – thermal insulation cylinder from mineral wool on the base of ba-salt rocks.Cylinders can be produced with lining of rein-forced aluminum foil.For the easy assembly onto the pipe the cylin-der has the longitudinal cutting on the outer side and the surface cutting, which is like a hinge on the inner side and is opposed to theouter cutting.
Application:In the civil and industrial engineering for new projects and reconstructions of the buildings with different functions as a thermal insula-tion material.Thermal insulation of the technological piping on the objects of different industries( includ-ing food industry) and the building systems. The limit temperature of application is plus 650°C. Degree of flammability is nonflam-mable.
Dimensions
Length
Diameter of pipe(inner diameter)
Thickness
1200 mm
18-324 mm
20-100 mm
Technical specification TU 5762-002-96667016-2008
Physical-mechanical characteristics
Density, kg/m3
l�10
l�25
l�125
l�300
70-110
0,048
0,087
0,035
Thermal conductivity, W/mК:
3,2Amount of organic substances, %, no more than
0,037
NonflammableFlammability degree
110-140
0,048
0,087
0,035
3,2
0,037
Nonflammable
CylinderTECHNONICOL 80
CylinderTECHNONICOL 100
Stone wool428
STITCHED MAT TECHNONICOLProduct description:Stitched Mat TechnoNICOL – nonflamma-ble, thermal and sound insulation stitched mat from mineral wool on the base of basalt rocks.It can be produced with the lining of aluminum foil or glass cloth.
Application:In the civil and industrial engineering for new projects and reconstructions of the buildings with different functions as a thermal insula-tion and fire protection material.It is used for the insulation of the pipes, coni-cal, cylindrical and flat surfaces, air ducts as a thermal, sound and fire-protection material.Zinc-coated steel net, which adds hardness to the insulation and eases the assembly, is sewed to the mat with the steel wire. It is used with the temperature of insulated surfaces up to 750°C.
DimensionsLength
Width
Thickness
2000 mm
1200 mm
50-100 mm
Technical specification TU 5762-002-96667016-2008
Physical-mechanical characteristics
Density, kg/m3
l�10
l�25
l�125
l�300
80
0,050
0,093
0,035
Thermal conductivity, W/mК:
50Compressibility, no more, %
0,038
60Elasticity, no less, %
NonflammableFlammability degree
100
0,049
0,090
0,034
40
0,037
70
Nonflammable
Stitched MatTECHNONICOL 80
Stitched MatTECHNONICOL 100
Stone wool 4 29
Product description:Lamella Mat TECHNONICOL is nonflammable, thermal and sound insulation mat, which is formed from the strips of mineral wool fibers, which is glued to the reinforced foil with the use of adhesive. As a result there is a productwhich has the increased compressive resis-tance in comparison with the standard mats and less deformation during the assembly.In standard execution mat is lined with the re-inforced foil.
Application:In the civil and industrial engineering for new projects and reconstructions of the buildings with different functions as a thermal insula-tion and fire protection material.It is used for the insulation of the pipes, coni-cal, cylindrical and flat surfaces, air ducts as a thermal, sound and fire-protection material.It is used with the temperature of insulated surfaces up to 250°C.
LAMELLA MAT TECHNONICOL
DimensionsLength
Width
Thickness
2500-12000 mm
1200 mm
20-100 mm
Technical specification TU- 5762-002-96667016-2008
Physical-mechanical characteristics
Density, kg/m3
l�10
l�25
l�125
Thermal conductivity, W/mК:
Elasticity, no less, %
Flammability degree
35
0,062
0,039
90
0,042
Nonflammable
Lamella Mat TECHNONICOL
Compressibility, no more, % 10
Stone wool430
FIREPROOF SLAB FOR THE IN-SULATION OF METALLIC CON-STRUCTIONS TECHNONICOLProduct description:Fireproof slab for the insulation of metal-lic constructions TECHNONICOL - nonflam-mable, thermal and sound insulation stitched mat from mineral wool on the base of basalt rocks.It can be produced with the lining of aluminum foil or glass cloth.
Application:In the civil and industrial engineering for new projects and reconstructions of the buildings with different functions as a thermal insula-tion and fire protection material for metallic constructions.For the fire protection of bearing metallic crossovers with foreresistance degree from 60 till 240 minutes.
DimensionsLength
Width
Thickness
1200 mm
600, 1200 mm
30-200 mm
Technical specification TU 5762-004-74182181-2008
Physical-mechanical characteristicsDensity, kg/m3
l�10
l�25
145
0,033
Thermal conductivity, W/mК:
0,035
30Compression strength at 10% deformation, kPa
EXTRUDED POLYSTYRENE
TECHNICAL SUPPORT AND INFORMATION ABOUT SALES OFFICES:Phone: +7 (495) 9255775, 8-800-200-05-65; Fax: +7 (495) 9258155
E-mail: [email protected] www.teplo.ru
Extruded polystyrene532
EXTRUDED POLYSTYRENE TECHNOPLEXDescriptions of material:The TECHNOPLEX extruded foamed poly-styrene is a thermal insulation material with uniformly distributed closed cells which does not absorb water, doesn’t swell and shrink, is chemical–resistant and is not subject to diges-tion.High resistibility allows to receive equal and simultaneously rigid base, and it essentially in-creases term of operation of the whole heat–insulating system.
Field of application:TECHNOPLEX –is an up–to–date thermal in-sulating material widely used in building and construction while arranging thermal protec-tion of the basement, roofs, floors, facades,thermal insulation of railways and highways.
DimensionsLength
Width
Thickness
1180-4500 mm
580 mm
20-120 mm
Technical specification TU 2244-047-17925162-2006
Physical-mechanical characteristics
Density, no less, kg/m3
Shrinkage resistance at 10 percent linear defor-mation, no less than (kPa)
Fire resistance category
Temperature range for normal operation, °C
38
0,35
0,2
0,030
Г4
0,032
TECHNOPLEX 45-500
32
0,35
0,2
0,029
Г4
0,031
TECHNOPLEX 35-300
STANDARD
32
0,035
0,2
0,029
Г1
0,031
TECHNOPLEX 35-250
28
0,30
0,2
0,029
Г4
0,031
TECHNOPLEX 30-250
STANDARD
28
0,30
0,2
0,029
Г1
0,031
0т -50 до +75
TECHNOPLEX 30-250
Thermal conductivity at (25±5) °С W/(m*°С), no more than
Projected thermal conductivity under condi-tions type «А» and «B»
Maximum strength for static bending, no less than,(MPa)
Water absorption, no more than(% of volume)
500300300250250
Extruded polystyrene 5 33
TECHNOPLEX KLIN is the Russian only wedge-shaped slabs set that makes it possible to create slopes and small-angle sloping on flat roofs, increase slopes through re-construc-tion of the existing roof, create small-angle sloping in the neck gutter running to the wa-ter intake holes, near duct shafts and roof lights, through arrangement of an extra slope so as to lead the water away from the barrier wall. TECHNOPLEX KLIN solves the problem of stagnant zones with optimal slopes on the roof. Stagnant zones cause top soil to appear on the roof. And, secondly, multiple and peri-odic freezing-melting of downfall in stagnant zones accelerates early malfunction of the en-tire roof structure.
TECHNOPLEX KLIN
Applications:1. Create roof slopes, increase the slope’s an-gle or change the water drainage route;2. Create small-angle slopes in gutters running to the leader heads;3. Create slopes (back gutters) next to the duct shafts and roof lights;4. Create extra slopes so as to take water away from barrier walls (counter slope).
Figure 1
Figure 2
Water intake hole
Extra slopeof barrier wall
Back gutter
Small-angleslope in gutter
Crossover calf
Slope
Extruded polystyrene534
TECHNOPLEX KLIN is:
A set of slabs A and B with 1,7% slope. It is used to create the main roof slope from the gutter to the ridge.
A set of J and K slabs with 3,4% slope. It is mostly used to create small-angle slopes between the water intake holes and to take away water from the barrier wall, roof lights and roof vent ducts.
Physical-mechanical characteristics
Min. compressibility at 10% deformation, kPa
Density, kg/m3
Operational temperature range
J and K slabs with 3,4% slope
Flammability degree
250
0,2
0,029
от -50 до+75
0,30
A and B slabs with 1,7% slope
Г1
Thermal conductivity at 25°C+/- °C, W(m*K)
Min. bending value, MPa
Max. water absorption, %
30,1 -38,0
250
0,2
0,029
от -50 до+75
0,30
Г1
30,1 -38,0
BITUMEN AND BITUMENPOLYMER MATERIALS
TECHNICAL SUPPORT AND INFORMATION ABOUT SALES OFFICES:Phone: +7 (495) 9255775, 8-800-200-05-65; Fax: +7 (495) 9258155
E-mail: [email protected] www.teplo.ru
Bitumen and bitumen polymer materials636
THE PREMUIM CLASS MATERIALS
TU 5774-003-00287852-99Roll roofing and waterproofing, welded-on bitumen-polymer material.
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Technoelast is produced by two-sided placement of bituminous poly-meric bonding material, consisting of bitumen, butadiene-styrene ther-moplastic elastomer and filler, on a fiberglass or polyester base. Coarse- and fine-grained coating compounds and polymer films are used as the protective layer.
Grades:Depending on the type of coating compound and the application area, Technoelast is produced in two grades:• technoelast K with coarse-grained coating compound on the face and a polymer film or fine-grained coating compound on the welded-on part of the material; it is used for installation of the top layer of roof clad-ding;• technoelast P with fine-grained coating compound or a polymer film or a composition thereof on both sides of the material; it is used for in-stallation of the bottom layer of roof cladding and for waterproofing of structures (basements, tunnels, etc).Technoelast is a bioresistant material.
Performance of work:According to the “Manual for Design and Installation of Roofing of Bi-tumen-Polymer Materials Manufactured by the TechnoNICOL Corpora-tion”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Technoelast
Bitumen and bitumen polymer materials 6 37
TU 5763-005-72746455-2007Roll soundproof interlaying material.
Features:Technoelast ACOUSTIC:• impact noise insulation.
Technoelast ACOUSTIC SUPER:• impact noise insulation• waterproofing.
Application area:Designed for installation of soundproof interlayer in floating floors or in other structures for the purpose of reducing the level of impact noise ac-cording to construction standards and regulations SNiP 23-03, and also for waterproofing thereof.
Composition:Technoelast ACOUSTIC is produced by two-sided placement of bitumi-nous polymeric bonding material on a fiberglass base with the subse-quent placement of a layer of soundproof geotextile on one side of the canvas, or by two-sided placement of bituminous polymeric bonding material on a soundproof fiberglass mat; for protection from agglutina-tion, polymer film is placed on the bituminous polymeric bonding mate-rial. Butadiene-styrene thermoplastic elastomer or modifications thereof are used for bitumen modification.
Grades:Depending on the structure of the canvas and the application area, Tech-noelast ACOUSTIC is produced in two grades:Technoelast ACOUSTIC SUPER: on a fiberglass base, on both sides of which bituminous polymeric bonding material is placed, with a layer of sound-proof geotextile on one side of the canvas, and polymeric pro-tective film on the other side of the canvas; it is used for installation of sound-proof interlayer and waterproofing of floating floors or other structures where impact noise insulation is required;Technoelast ACOUSTIC: on a soundproof fiberglass base, on one side of which bituminous polymeric bonding material is placed, protected by a polymeric protective film; it is used for installation of soundproof inter-layer in floating floors or other structures where impact noise insulation is required.
Performance of work:According to the “Manual for Application of Technoelast ACOUSTIC and Technoelast ACOUSTIC SUPER Soundproof Materials”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Technoelast ACOUSTIC &Technoelast ACOUSTIC-SUPER
Bitumen and bitumen polymer materials638
TU 5774-004-72746455-2007Roll waterproofing, self-adhesive, bitumen-polymer material.
Features:• fireless placement: used where open fire is forbidden, placement on a combustible base is possible;• placement without any additional equipment;• placement in an enclosed or confined space.
Application area:Designed for installation of waterproof and vapor-proof barriers of structures.
Composition:Technoelast BARRIER is produced by two-sided placement of bitumen-polymer adhesive bonding material, consisting of bitumen, butadiene-styrene thermoplastic elastomer and fabrication aids, on a polyester base. The material is protected with a thick polymer film on the top and is covered with siliconized anti-adhesive film on the bottom.
Performance of work:According to the “Manual for Design and Installation of Roofing Con-sisting of Bitumen-Polymer Material Manufactured by TechnoNICOL Roofing Company”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Technoelast BARRIER
TU 5774-041-17925162-2006Roll water- and gas-proof, welded-on bitumen-polymer material.
Features:Protection from Radon radioactive gas.
Application area:Designed for water- and gas-proofing of underground parts of build-ings and structures.
Composition:Technoelast ALFA is produced by two-sided placement of bituminous polymeric bonding material, consisting of bitumen, polymeric modifier and filler, on a polyester base coupled with metal foil, with subsequent placement of protective layers on both sides of the material. Butadiene-styrene thermoplastic elastomer or modifications thereof are used for bitumen modification. Polymer film is used as the protective layer.
Performance of work:According to the “Manual for Design and Installation of Waterproofing and Gas-Proofing of Underground Parts of Buildings and Structures Us-ing Technoelast ALFA Material”, it may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Technoelast ALFA
Bitumen and bitumen polymer materials 6 39
TU 5774-003-00287852-99Roll roofing, welded-on bitumen-polymer material.
Features:May be used on roofs with high facade value owing to its cross-linked polyether base.Wide color range of the top basalt dressing compound:
Technoelast DECOR
blue mix brown mix green mix red mix
Application area:Designed for construction of the top layer of a multi-layer roof clad-ding.
Composition:Technoelast DECOR is produced by two-sided placement of bituminous polymeric bonding material, consisting of bitumen, polymer modifier (SBS) and filler, on the base (cross-linked polyester), with subsequent placement of protective layers on both sides of the material: coarse-grained basalt coating compound on the top and polymer film on the bottom.
Performance of work:According to the “Manual for Design and Installation of Roofing of Bi-tumen-Polymer Materials Manufactured by the TechnoNICOL Roofing Company”, may be used in all climate zones as per construction stan-dards and regulations SNiP 23-01.
Bitumen and bitumen polymer materials640
TU 5774-003-00287852-99Roll roofing and waterproofing, welded-on bitumen-polymer material.
Features:• mechanically attached to the base;• possibility of installing “breathing” roofing;• does not require priming of the base surface.
Application area:Technoelast FIX is designed for installation of bottom layers of roof cladding of buildings and structures.
Composition:Technoelast FIX is produced by two-sided placement of bituminous polymeric bonding material, consisting of bitumen, butadiene-styrene thermoplastic elastomer and filler, on a cross-linked polyester base. Coarse-grained sand on the bottom and a polymer film on the top are used as the protective layers.
Performance of work:According to the “Manual for Design and Installation of Roofing with Mechanical Fixation of Roof Cladding with the Use of Technoelast FIX and Technoelast SOLO Materials”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Technoelast FIX
Bitumen and bitumen polymer materials 6 41
TU 5774-001-72746455-2006Roll roofing and waterproofing, welded-on bitumen-polymer material.
Features:The material has enhanced fire hazard properties according to construc-tion standards and regulations SNiP 21.01:• flame spread group RP1 (non-flame spreading);• flammability group V2 (medium flammable).
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Technoelast FLAME-STOP is produced by two-sided placement of bitu-minous polymeric bonding material, consisting of bitumen, polymeric modifier, fire-retardants, and filler, on a fiberglass (mat, cloth) or poly-ester base, with subsequent placement of protective layers on both sides of the material. Coarse-grained (slate) and fine-grained (sand) coating compounds and polymer film are used as the protective layers.
Grades:Depending on the type of protective covers and the application area, Technoelast FLAME-STOP is produced in the following grades:Technoelast FLAME-STOP K with coarse-grained coating compound on the face and a polymer film or fine-grained coating compound on the bottom of the material; it is used for installation of the top layer of roof cladding.
Performance of work:According to the “Manual for Design and Installation of Bitumen-Poly-mer Roofing Manufactured by the TechnoNICOL Corporation”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Technoelast FLAME STOP
Bitumen and bitumen polymer materials642
TU 5774-012-17925162-2004Roll waterproofing, root-proof, welded-on bitumen-polymer material.
Features:• resistance against damage by plant roots;• chemical and mechanical protection from root sprouting.
Application area:Designed for waterproofing of structures, including all types of green roofs where contact of the waterproof layer with root systems of plants is possible.
Composition:Technoelast GREEN is produced by two-sided placement of bituminous polymeric bonding material, consisting of bitumen, butadiene-styrene thermoplastic elastomer or modifications thereof, filler and root-proof admixtures, on a polyester base, with subsequent placement of protec-tive layers on both sides of the material. As the protective layers, coarse- and fine-grained (sand) coating compounds and polymer films are used.
Grades:Depending on the type of protective covers and the application area, Technoelast GREEN is produced in the following grades:• Technoelast GREEN K with coarse-grained coating compound on the face and a polymer film on the bottom part of the material; it is used for installation of the top layer of roof cladding;• Technoelast GREEN P with polymer film on both sides of the material; it is used for waterproofing of structures.
Performance of work:According to the “Manual for Design and Installation of Green Roofs Using Technoelast GREEN Material with Reinforced Protection from Penetration of Plant Root Systems”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Technoelast GREEN
Bitumen and bitumen polymer materials 6 43
TU 5774-003-00287852-99Roll roofing and waterproofing, welded-on bitumen-polymer material.
Features:• fireless placement on mastic;• composition of seamless and roll-fed roofs.
Application area:Technoelast PRIME is designed for construction of roof cladding of buildings and structures and for waterproofing of structures. Used for installation of two-layer roof claddings with mastic adhesion. This tech-nology combines the advantages of Roofing of roll materials (with high mechanical properties) and seamless solid mastic roofs.
Composition:Technoelast PRIME is produced by two-sided placement of bituminous polymeric bonding material, consisting of bitumen, butadiene-styrene thermoplastic elastomer and filler, on a polyester base. Coarse- or fine-grained coating compounds are used as the protective layer.
Grades:Depending on the type of coating compound and the application area, Technoelast PRIME is produced in two grades:• Technoelast PRIME EKM with coarse-grained coating compound on the face and fine-grained coating compound on the bottom of the ma-terial; it is used for installation of the top layer of roof cladding• Technoelast PRIME EMM with fine-grained coating compound on both sides of the material; it is used for installation of the bottom layer of roof cladding.
Performance of work:According to the “Manual for Design and Installation of Roofing of Technoelast PRIME and Technoelast SОLO Materials Manufactured by the TechnoNICOL Roofing Company and Laid on Cold Mastic”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Technoelast PRIME
Bitumen and bitumen polymer materials644
Technoelast STU 5774-005-17925162-2002Roll roofing and waterproofing, self-adhesive bitumen-polymer mate-rial.
Features:• fireless placement: possible application in places, where open fire is forbidden, placement on a flammable base is allowed;• placement without any additional equipment;• placement in enclosed or confined space.
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Technoelast S is produced by two-sided placement of bituminous poly-meric bonding material, consisting of bitumen, butadiene-styrene ther-moplastic elastomer or modifications thereof and filler, on a fiberglass or polyester base, with subsequent placement of an adhesive layer on the bottom part of the material. Coarse- or fine-grained coating com-pounds, anti-adhesive polymer film or paper are used as the protective layer.
Grades:Depending on the type of protective layer and the application area, Technoelast S is produced in two grades:• Technoelast S EKS with coarse-grained coating compound on the face and anti-adhesive polymer film or paper on the bottom of the material; it is used for installation of single-layer roofing;• Technoelast S EMS with fine-grained coating compound or anti-ad-hesive polymer film or paper on the face and anti-adhesive polymer film or paper on the bottom of the material; it is used for installation of the bottom layer of double-layer roof cladding, including installation on combustible base.
Performance of work:According to the “Manual for Design and Installation of Roofing Con-sisting of Technoelast S Self-Adhesive Material Manufactured by the TechnoNICOL Company”, may be used in all climate zones as per con-struction standards and regulations SNiP 23-01.
Bitumen and bitumen polymer materials 6 45
TU 5774-003-00287852-99Roll roofing and waterproofing, welded-on bitumen-polymer material.
Features:• single-layer roofing;• fireless placement is possible;• placement on mastic;• mechanical fixing;• traditional placement by welding-on.
Application area:Technoelast SOLO is designed for installation of single-layer roof clad-ding of buildings and structures and for waterproofing of structures.
Composition:Technoelast SOLO is produced by two-sided placement of bituminous bonding material, consisting of bitumen, butadiene-styrene thermoplas-tic elastomer and filler, on a cross-linked polyester base. Coarse-grained (grey slate) coating compound on the top and fine-grained sand on the bottom are used as the protective layers.
Grades:The material is produced in two grades:• Technoelast SOLO for mechanical fixing with coarse-grained coating compound on the face and fine-grained sand on the bottom of the ma-terial. A longitudinal overlapping edge 100-120 mm in width is covered with a polymer film. It is used for installation of single-layer roof clad-ding using mechanical fixing and welding-on;• Technoelast SOLO for placement on mastic with coarse-grained coat-ing compound on the face and fine-grained sand on the bottom of the material. A longitudinal overlapping edge 100-120 mm in width is cov-ered with siliconized anti-adhesive film. It is used for installation of sin-gle-layer roof cladding using placement on mastic.
Performance of work:According to the “Manual for Design and Installation of Roofing with Mechanical Fixation of Roof Cladding with the Use of Technoelast FIX and Technoelast SOLO Materials”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Technoelast SOLO
Bitumen and bitumen polymer materials646
TU 5774-040-17925162-2005Roll roofing and waterproofing, welded-on bitumen-polymer material.
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Technoelast THERMO is produced by two-sided placement of bitumi-nous polymeric bonding material, consisting of bitumen, polymer modi-fier and filler, on a fiberglass (mat, cloth) or polyester base, with sub-sequent placement of protective layers on both sides of the material. Atactic and isotactic polypropylenes or similar polyolefins are used for bitumen modification. Coarse-grained (slate, asbestos chips) coating compound and polymer film are used as the protective layers.
Grades:Depending on the type of coating compounds and the application area, Technoelast THERMO is produced in the following grades:• Technoelast THERMO K with coarse-grained coating compound on the face and a polymer film on the welded-on part of the material; it is used for installation of the top layer of roof cladding;• Technoelast THERMO P with fine-grained coating compound on both sides of the material; it is used for installation of the bottom layer of roof cladding and for waterproofing of structures.
Performance of work:According to the “Manual for Design and Installation of Roofing of Bi-tumen-Polymer Materials Manufactured by the TechnoNICOL Roofing Company”, may be used in all climate zones as per construction stan-dards and regulations SNiP 23-01.
Technoelast THERMO
Bitumen and bitumen polymer materials 6 47
TU 5774-030-17925162-2005Roll roofing and waterproofing, welded-on bitumen-polymer material.
Features:• flexibility on a R=10.0±0.2 mm beam at minus 35°C;• heat endurance 140°C;• basalt coating compound (blue mix) on the top;• may be used on roofing with a large slope.
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Technoelast TITAN is produced by two-sided placement of bituminous polymeric bonding material, consisting of bitumen, polymer modifier and filler, on polyester nonwoven fabric, with subsequent placement of protective layers on both sides of the material. Atactic and isotactic poly-propylenes are used for bitumen modification. Coarse- and fine-grained (sand) coating compounds and polymer films are used as the protective layers.
Grades:Depending on the base structure, type of coating compound and the ap-plication area, Technoelast TITAN is produced in the following grades:• Technoelast TITAN TOP on a single-layer base with coarse-grained coating compound on the face and a polymer film on the bottom of the material; it is used for installation of the top layer of a multi-layer roof cladding;• Technoelast TITAN BASE on a single-layer base with polymer films on the top and bottom sides of the material; it is used for installation of the bottom layers of multi-layer roof cladding and for waterproofing of structures;• Technoelast TITAN SOLO with coarse-grained coating compound on the face and a polymer film or fine-grained coating compound on the bottom of the material; it is used for installation of a single-layer roof cladding and for waterproofing of structures.
Performance of work:According to the “Manual for Design and Installation of Roofing of Bi-tumen-Polymer Materials Manufactured by the TechnoNICOL Roofing Company”, may be used in all climate zones as per construction stan-dards and regulations SNiP 23-01.
Technoelast TITAN
Bitumen and bitumen polymer materials648
TU 5774-003-00287852-99Roll roofing and waterproofing, welded-on bitumen-polymer material.
Features:• material for “breathing” roofing, with strip adhesion to the base;• possibility of installation of a single-layer roof cladding;• solves the problem of blubs on roofing;• increases labor productivity.
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Technoelast VENT is produced by two-sided placement of bituminous polymeric bonding material, consisting of bitumen, butadiene-styrene thermoplastic elastomer and filler, on a polyester base. Coarse-grained (slate) coating compound on the top and a ventilated surface on the bottom are used as the protective layer. The ventilated surface has strips of bituminous polymeric bonding material, the space between which is filled with fine-grained sand, and the whole surface is covered with a polymer film.
Performance of work:According to the “Manual for Design and Installation of “Breathing” Roofing Consisting of Technoelast VENT and Uniflex VENT Welded-on Roll Materials”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Technoelast VENT
Bitumen and bitumen polymer materials 6 49
TU 5774-004-17925162-2003Roll waterproofing, welded-on bitumen-polymer material.
Features:• TECHNOELASTMOST S grade withstands the temperature of cast as-phalt when the latter is being placed (up to 220°C);• Fixed material width;• TECHNOELASTMOST S grade withstands impact puncture testing up to 250N
Application area:Designed for waterproofing of reinforced concrete slabs of traffic ways of bridge superstructures, installation of a protective and coupling layer on steel orthotropic slabs of bridge superstructures, and also for water-proofing of other structures.
Composition:TECHNOELASTMOST is produced by two-sided placement of bituminous polymeric bonding material, consisting of bitumen, polymer modifier and filler, on a polyester base, with subsequent placement of protective layers on both sides of the material. Butadiene-styrene thermoplastic elastomer, isotactic polypropylene and polyolefins are used for bitumen modification. Fine-grained coating compound and (or) polymer films are used as the protective layers.
Grades:Depending on the application area, TECHNOELASTMOST is produced in two grades:• TECHNOELASTMOST B for waterproofing of reinforced concrete slabs of traffic ways of bridge superstructures and waterproofing of other structures;• TECHNOELASTMOST S for installation of a protective and coupling layer on steel orthotropic slabs of bridge superstructures, and also for waterproofing of bridge superstructures with reinforced concrete slabs as the traffic way base, on which asphalt concrete pavement, including cast mixtures with a temperature of up to 220 °С, is laid directly on the waterproofing layer.
Performance of work:According to the “Recommendations for Waterproofing of Bridgeworks with TECHNOELASTMOST Roll Welded-on Materials”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
TECHNOELASTMOST
Bitumen and bitumen polymer materials650
THE BUSINESS CLASSMATERIALS
TU 5774-003-17925162-2000Roll roofing and waterproofing, welded-on material.
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Ecoflex is produced by two-sided placement of bituminous bonding ma-terial, consisting of bitumen, filler and fabrication aids, on a fiberglass (mat, cloth) or polyester base, with subsequent placement of protec-tive layers on both sides of the material. Coarse-grained (slate, asbestos chips) or fine-grained (sand) coating compounds and polymer film are used as the protective layer.
Grades:Depending on the type of coating compound and the application area, Ecoflex is produced in two grades:• Ecoflex K with coarse-grained coating compound on the face and a polymer film on the welded-on part of the material; it is used for instal-lation of the top layer of roof cladding;• Ecoflex P with polymer film on both sides of the material; it is used for installation of the bottom layers of roof cladding and for waterproofing of structures.
Performance of work:According to the “Manual for Design and Installation of Bituminous Roofing Manufactured by the TechnoNICOL Roofing Company”, may be used in all climate zones as per construction standards and regula-tions SNiP 23-01.
Ecoflex
Bitumen and bitumen polymer materials 6 51
TU 5774-001-17925162-99Roll roofing and waterproofing, welded-on bitumen-polymer material.
Application area:Designed for installation of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Uniflex is produced by two-sided placement of bituminous polymeric bonding material, consisting of bitumen, butadiene-styrene thermo-plastic elastomer and filler, on a fiberglass or polyester base. Coarse- and fine-grained coating compounds, foil and polymer film are used as the protective layer.
Grades:Depending on the type of coating compound and the application area, Uniflex is produced in two grades:• Uniflex K with coarse-grained coating compound or foil on the face and a polymer film on the welded-on part of the material; it is used for installation of the top layer of roof cladding;• Uniflex P with a polymer film or fine-grained coating compound on both sides of the material; it is used for installation of the bottom layers of roof cladding and for waterproofing of structures.
Performance of work:According to the “Manual for Design and Installation of Roofing of Bi-tumen-Polymer Materials Manufactured by the TechnoNICOL Roofing Company”, may be used in all climate zones as per construction stan-dards and regulations SNiP 23-01.
Uniflex
Bitumen and bitumen polymer materials652
TU 5774-001-17925162-99 Roll roofing and waterproofing, welded-on bitumen-polymer material.
Features:• material for “breathing” roofing, with strip-based adhesion to the base;• resolves the issue of blubs on roofing;• increases labor productivity.
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Uniflex VENT is produced by two-sided placement of bituminous poly-meric bonding material, consisting of bitumen, butadiene-styrene thermoplastic elastomer and filler, on a polyester base. Coarse-grained (slate) and fine-grained (sand) coating compounds on the top and a ventilated surface on the bottom are used as the protective layer. The ventilated surface has strips of bituminous polymeric bonding material, the space between which is filled with fine-grained sand, and the whole surface is covered with a thin polymer film.
Grades:Depending on the type of coating compound and the application area, Uniflex VENT is produced in two grades:• Uniflex VENT EKV with coarse-grained coating compound on the face and a ventilated covering on the welded-on part of the material; it is used for repairing roofing without removal of the old roof cladding;• Uniflex VENT EPV (TPV) with a polymer film on the face and a ventilat-ed covering on the welded-on part of the material; it is used for installa-tion of the bottom layers of double-layer roof cladding and for repairing roofs without removal of the old roof cladding.
Performance of work:According to the “Manual for Design and Installation of “Breathing” Roofing Consisting of Technoelast VENT and Uniflex VENT Welded-on Roll Materials”, may be used in all climate zones as per construction stan-dards and regulations SNiP 23-01.
Uniflex VENT
Bitumen and bitumen polymer materials 6 53
THE STANDARD & ECONOMIC CLASS
TU 5774-019-17925162-2003Roll roofing and waterproofing, welded-on material.
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Bicroelast is produced by two-sided placement of bituminous bonding material, consisting of bitumen, filler and fabrication aids, on a fiber-glass (mat, cloth) or polyester base, with subsequent placement of pro-tective layers on both sides of the material. Coarse-grained (slate, asbes-tos chips) and fine-grained (sand) coating compounds and polymer film are used as the protective layers.
Grades:Depending on the type of protective covers and the application area, Bi-croelast is produced in the following grades:• Bicroelast K, Bicroelast Tropic K with coarse-grained coating compound on the face and a polymer film on the welded-on part of the material; it is used for installation of the top layer of roof cladding;• Bicroelast P, Bicroelast Tropic P with fine-grained coating compound or a polymer film on the face and a polymer film on the bottom of the material or fine-grained coating compound on both sides of the mate-rial; it is used for installation of the bottom layers of roof cladding and for waterproofing of structures.
Performance of work:According to the “Manual for Design and Installation of Roofing Consist-ing of Bituminous Materials Manufactured by the TechnoNICOL Corpo-ration”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Bicroelast
Bitumen and bitumen polymer materials654
TU 5774-042-00288739-99Roll roofing and waterproofing, welded-on material.
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Bicrost is produced by two-sided placement of bituminous bonding ma-terial, consisting of bitumen and filler, on a fiberglass (mat, perforated mat, reinforced cloth) or polyester base, with subsequent placement of protective layers on both sides of the material. Coarse-grained (slate, as-bestos chips) and fine-grained (sand) coating compounds and polymer film are used as the protective layers.
Grades:Depending on the type of protective covers and the application area, Bi-crost is produced in two grades:• Bicrost K with coarse-grained coating compound on the face and a polymer film on the bottom of the material; it is used for installation of the top layer of roof cladding;• Bicrost P with fine-grained coating compound or a polymer film on the face and a polymer film on the bottom of the material or fine-grained coating compound on both sides of the material; it is used for instal-lation of the bottom layers of roof cladding and for waterproofing of structures.
Performance of work:According to the “Manual for Design and Installation of Bituminous Roofing Consisting of Bituminous Materials Manufactured by the Tech-noNICOL Roofing Company”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Bicrost
Bitumen and bitumen polymer materials 6 55
TU 5774-008-17925162-2002Roll roofing and waterproofing, welded-on material.
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Bipole is produced by two-sided placement of bituminous bonding ma-terial, consisting of bitumen, filler and fabrication aids, on a fiberglass (mat, cloth) or polyester base, with subsequent placement of protec-tive layers on both sides of the material. Coarse-grained (slate, asbestos chips) and fine-grained (sand) coating compounds and polymer film are used as the protective layers.
Grades:Depending on the type of protective covers and the application area, Bipole is produced in the following grades:• Bipole K, Bipole Tropic K with coarse-grained coating compound on the face and a polymer film on the welded-on part of the material; it is used for installation of the top layer of roof cladding;• Bipole P, Bipole Tropic P with fine-grained coating compound or a polymer film on the face and a polymer film on the bottom of the ma-terial or fine-grained coating compound on both sides of the material; it is used for installation of the bottom layers of roof cladding and for waterproofing of structures.
Performance of work:According to the “Manual for Design and Installation of Bituminous Roofing Consisting of Bituminous Materials Manufactured by the Tech-noNICOL Roofing Company”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Bipole
TU 5774-002-13157915-98Roll roofing and waterproofing, welded-on material.
Application area:Designed for construction of roof cladding of buildings and structures and for waterproofing of structures.
Composition:Linocrome is produced by two-sided placement of bituminous bonding material, consisting of bitumen and filler, on a fiberglass (mat, cloth) or polyester base, with subsequent placement of protective layers on both sides of the material. Coarse-grained (slate, asbestos chips) and fine-grained (sand) coating compounds and polymer film are used as the protective layers
Grades:Depending on the type of protective covers and the application area, Linocrome is produced in two grades:• Linocrome K with coarse-grained coating compound on the face and a polymer film on the welded-on part of the material; it is used for instal-lation of the top layer of roof cladding;• Linocrome P with fine-grained coating compound or a polymer film on the face and a polymer film on the bottom of the material or fine-grained coating compound on both sides of the material; it is used for installation of the bottom layers of roof cladding and for waterproofing of structures.
Performance of work:According to the “Manual for Design and Installation of Bituminous Roofing Consisting of Bituminous Materials Manufactured by the Tech-noNICOL Roofing Company”, may be used in all climate zones as per construction standards and regulations SNiP 23-01.
Linocrome
Bitumen and bitumen polymer materials656
Bitumen and bitumen polymer materials 6 57
THE PREMUIM CLASS MATERIALSPhysical-mechanical characteristics
4,6
Technoelast P
film
100
-
-
-
-
-
absolute
minus 25
minus 35
1
294/-
600/400
4,0
-
minus 25
10х1
-
-
-
-
-
2
800/900
film
-
5
Technoelast K
slate
-
-
-
-
-
100
-
minus 25
minus 35
1
294/-
600/400
4,2
absolute
minus 25
-
-
-
-
-
10х1
1
2
800/900
film
-
1,45
TechnoelastACOUSTIC
film
-
-
-
21
0,2
-
-
-
-
-
170
-
2,5
-
-
-
-
-
15х1
-
-
-
-
-
-
3,3
TechnoelastACOUSTIC
SUPER
film
-
-
-
26
0,25
85
absolute
-
minus 25
2
300
-
4,8
-
-
-
-
-
10х1
minus 15
-
-
-
-
-
4,6
TechnoelastALFA
film
-
-
-
-
-
100
absolute
minus 20
minus 30
1
-
600/400
4,0
-
-
-
-
-
10х1
minus 20
-
2
-
film
-
2,2
TechnoelastBARRIER
polymer film
-
0,5(0,5)
0.2(2.0)
-
-
85
absolute
minus 25
minus 35
1
-
343
2,2
-
-
150
2(2)
0.2(2.0)
20х1
minus 25
-
-
-
antiadhesiverelease
Mass of 1 sq. m, kg, not less than
Thickness*, mm
polyester
glass-fibre mat
Water absorption during 24 h, mass %, not to exceed
Brittle point of the bonding material, °C, not to exceed
Bend point on a R=10 mm beam, °C, not to exceed
on the top
Heat endurance, °C, not less than
to concrete
Tear resistance of the adhesive joint, kNper m (kgf per cm), not less than
Static puncture resistance, H, during 24 hours, not less than
Resistance to tear by nail shank, H, not less than
Noise reduction index, rLn, dB, not less than
Dynamic modulus of elasticity at the load of2 kPa, MPa, not to exceed
Water resistance at water pressure of not less than 0,2 MPa during 2 h
Longitudinal / transverse breaking load, H, not less than
glass-cloth
Mass of the bonding material on the weldedonside, kg per sq. m, not less than
Roofing sand loss, g per sample, not to exceed
Bend point on a R=25 mm beam, °C, not to exceed
Water resistance at water pressure of not less than 0,001 MPa during 72 h
Length / width, m
to metal
Shear strength of the adhesive joint, kN perm (kgf per cm), not less than
Static pressing-through resistance, H,during 24 hours, not less than
Water resistance at water pressure of notless than 0,2 MPa during 42 h
Protective covering type
on the bottom
Adhesion strength, MPa (kgf per sq. cm),not less than
-
5
TechnoelastDECOR
colored basalt
-
-
-
-
-
100
-
minus 25
minus 35
1
-
600/400
4,2
absolute
-
-
-
-
10х1
minus 25
1
2
-
film
Bitumen and bitumen polymer materials658
THE PREMUIM CLASS MATERIALSPhysical-mechanical characteristics
-
5
TechnoelastGREEN P
film
-
-
-
-
-
100
absolute
minus 25
minus 35
1
-
600/400
3,8
-
-
-
-
-
10х1
minus 25
-
2
-
film
-
5
TechnoelastGREEN K
slate
-
-
-
-
-
100
-
minus 25
minus 35
1
-
600/400
4,2
absolute
-
-
-
-
10х1
minus 25
1
2
-
film
-
5
Technoelast FLAME STOP K
slate
-
-
-
-
-
100
-
minus 25
minus 35
1
294/-
600/400
4,2
absolute
-
-
-
-
10х1
minus 25
1
2
800/900
film
-
3,0
TechnoelastPRIME EMM
sand
-
-
-
-
-
100
absolute
minus 25
minus 35
1
-
600/600
3,0
-
-
-
-
-
10х1
minus 25
-
-
-
sand
-
4
TechnoelastPRIME EKM
slate
-
-
-
-
-
100
-
minus 25
minus 35
1
-
600/600
4,0
absolute
-
-
-
-
10х1
minus 25
1
-
-
sand
-
5
Technoelast SEKS
slate
-
0,5(0,5)
0.2(2.0)
-
-
100
-
minus 25
minus 35
1
-
600/400
4,2
absolute
-
-
2(2)
0.2(2.0)
10х1
minus 25
1
-
-
film
Mass of 1 sq. m, kg, not less than
Thickness*, mm
polyester
glass-fibre mat
Water absorption during 24 h, mass %, not to exceed
Brittle point of the bonding material, °C, not to exceed
Bend point on a R=10 mm beam, °C, not to exceed
on the top
Heat endurance, °C, not less than
to concrete
Tear resistance of the adhesive joint, kNper m (kgf per cm), not less than
Static puncture resistance, H, during 24 hours, not less than
Resistance to tear by nail shank, H, not less than
Noise reduction index, rLn, dB, not less than
Dynamic modulus of elasticity at the load of2 kPa, MPa, not to exceed
Water resistance at water pressure of not less than 0,2 MPa during 2 h
Longitudinal / transverse breaking load, H, not less than
glass-cloth
Mass of the bonding material on the weldedonside, kg per sq. m, not less than
Roofing sand loss, g per sample, not to exceed
Bend point on a R=25 mm beam, °C, not to exceed
Water resistance at water pressure of not less than 0,001 MPa during 72 h
Length / width, m
to metal
Shear strength of the adhesive joint, kN perm (kgf per cm), not less than
Static pressing-through resistance, H,during 24 hours, not less than
Water resistance at water pressure of notless than 0,2 MPa during 42 h
Protective covering type
on the bottom
Adhesion strength, MPa (kgf per sq. cm),not less than
260
4
TechnoelastFIX
film
-
-
-
-
-
-
-
-
-
10х1
100
absolute
-
minus 25
minus 25
minus 35
-
1
-
-
-
600/600
3
hardgrainedsand
Bitumen and bitumen polymer materials 6 59
-
6
TechnoelastVENT
slate
-
-
-
-
-
100
-
minus 25
minus 35
1
-
1000/-
-
absolute
-
-
-
-
8х1
minus 25
1
2
-
ventilatedsurface
-
6
TECHNO-ELASTMOST B
sand
-
-
-
-
-
100
-
minus 25
minus 35
1
-
600/600
5,0
-
absolute
-
-
-
8х1
minus 25
-
2
-
film
-
5,8
TECHNO-ELASTMOST S
sand
250
-
-
-
-
140
-
minus 25
minus 35
1
-
1000/900
5,2
-
absolute
-
-
-
8х1
minus 25
-
2,5
-
film
-
3,4
Technoelast SEMS
sand
-
0,5(0,5)
0.2(2.0)
-
-
100
absolute
minus 25
minus 35
1
-
500/300
3,2
-
-
-
2(2)
0.2(2.0)
10х1
minus 25
-
-
-
film
-
6
Technoelast SOLO
slate
-
-
-
-
-
1000
-
minus 25
minus 35
1
-
1000/-
5,0
absolute
-
-
-
-
8х1
minus 25
1
2
-
sand
-
4,6
TechnoelastTHERMO P
film
-
-
-
-
-
-
-
-
-
10х1
130
absolute
-
minus 15
minus 15
minus 25
-
1
2
294/-
800/900
600/400
4,0
film
-
5
Technoelast THERMO K
slate
-
-
-
-
-
-
-
-
-
10х1
130
-
absolute
minus 15
minus 15
minus 25
1
1
2
294/-
800/900
600/400
4,2
film
-
4,5
TechnoelastTITAN BASE
film
-
-
-
-
-
-
-
-
-
10х1
140
absolute
-
minus 35
minus 35
minus 40
-
1
2
-
-
600/400
4
film
-
5,5
TechnoelastTITAN TOP
basalt
-
-
-
-
-
-
-
-
-
10х1
140
-
absolute
minus 35
minus 35
minus 40
1
1
2
-
-
600/400
4,5
film
-
5,8
TechnoelastTITAN SOLO
basalt
-
-
-
-
-
-
-
-
-
8х1
140
-
absolute
minus 35
minus 35
minus 40
1
1
2
-
-
1000
5
film
Bitumen and bitumen polymer materials660
THE BUSINESS CLASS MATERIALS
Physical-mechanical characteristics
Mass of 1 sq. m, kg, not less than
Thickness*, mm
glass-cloth
Mass of the bonding material on the welded-on side, kg per sq. m, not less than
Roofing sand loss, g per sample, not to exceed
Bend point on a R=25 mm beam, °C, not to exceed
Water resistance at water pressure of not less than 0,001 MPa during 72 h
on the top
Heat endurance, °C, not less than
Length / width, m
Water resistance at water pressure of not less than 0,2 MPa during 2 h
Brittle point of the bonding material, °C, not to exceed
Water absorption during 24 h, mass %, not to exceed
glass-fibre mat
polyester
Longitudinal / transverse breaking load, H, not less than
Protective covering type
on the bottom
4,7
Uniflex K
granulatedmaterial,
slate
10х1
95
-
absolute
minus 20
minus 30
1
1
2
294
800/900
500/350
3,8
film
3,2
UniflexVENT TPV
film
10х1
95
absolute
-
minus 20
minus 30
-
1
2
-
800/900
-
-
ventilatedcover
4
UniflexVENT EPV
film
10х1
95
absolute
-
minus 20
minus 30
-
1
2
500/350
-
-
-
ventilatedcover
5,5
UniflexVENT EKV
granulatedmaterial,
slate
10х1
95
-
absolute
minus 20
minus 30
1
1
2
600/400
-
-
-
ventilatedcover
3,5
Ecoflex P
film
10х1
130
absolute
-
minus 10
minus 15
-
1
1,5
294
800/900
500/350
2,8
film
4,6
Ecoflex K
granulatedmaterial,
slate
10х1
130
-
absolute
minus 10
minus 15
1
1
1,5
294
800/900
500/350
3,8
film
3,6
Uniflex P
film
10х1
95
absolute
-
minus 20
minus 30
-
1
2
294
800/900
500/350
2,8
film
Bitumen and bitumen polymer materials 6 61
THE STANDARD & ECONOMIC CLASS MATERIALSPhysical-mechanical characteristics
Mass of 1 sq. m, kg, not less than
Thickness*, mm
glass-cloth
Mass of the bonding material on the welded-on side, kg per sq. m, not less than
Roofing sand loss, g per sample, not to exceed
Bend point on a R=25 mm beam, °C, not to exceed
Water resistance at water pressure of not less than 0,001 MPa during 72 h
on the top
Heat endurance, °C, not less than
Length / width, m
Water resistance at water pressure of not less than 0,2 MPa during 2 h
Brittle point of the bonding material, °C, not to exceed
Water absorption during 24 h, mass %, not to exceed
glass-fibre mat
polyester
Longitudinal / transverse breaking load, H, not less than
Protective covering type
on the bottom
4,0
Bipole K
granulatedmaterial,
slate
10х1
85
-
absolute
minus 15
minus 25
1
1
1,5
294
800
360
-
film
3,0
BicroelastP
film
15х1
85
absolute
-
minus 10
minus 25
-
1
1,5
294
800
360
-
film
4,0
BicroelastK
granulatedmaterial,
slate
10х1
85
-
absolute
minus 10
minus 25
1
1
1,5
294
800
360
-
film
3,0
BicroelastTropic P
film
15х1
100
absolute
-
0
minus 15
-
1
1,5
294
800
360
-
film
4,0
BicroelastTropic K
granulatedmaterial,
slate
10х1
100
-
absolute
0
minus 15
1
1
1,5
294
800
360
-
film
3,0
Bicrost P
film
15х1
80
absolute
-
0
minus 15
-
1
1,5
294
1000
343
-
film
4,0
Bicrost K
granulatedmaterial,
slate
10х1
80
-
absolute
0
minus 15
1
1
1,5
294
1000
343
-
film
Bitumen and bitumen polymer materials662
THE STANDARD & ECONOMIC CLASS MATERIALSPhysical-mechanical characteristics
Mass of 1 sq. m, kg, not less than
Thickness*, mm
glass-cloth
Mass of the bonding material on the welded-on side, kg per sq. m, not less than
Roofing sand loss, g per sample, not to exceed
Bend point on a R=25 mm beam, °C, not to exceed
Water resistance at water pressure of not less than 0,001 MPa during 72 h
on the top
Heat endurance, °C, not less than
Length / width, m
Water resistance at water pressure of not less than 0,2 MPa during 2 h
Brittle point of the bonding material, °C, not to exceed
Water absorption during 24 h, mass %, not to exceed
glass-fibre mat
polyester
Longitudinal / transverse breaking load, H, not less than
Protective covering type
on the bottom
3,0
Bipole P
film
15х1
85
absolute
-
minus 15
minus 25
-
1
1,5
294
800
360
-
film
3,0
BipoleTropic P
film
15х1
120
absolute
-
minus 5
minus 15
-
1
1,5
294
800
360
-
film
4,0
BipoleTropic K
granulatedmaterial,
slate
10х1
120
-
absolute
minus 5
minus 15
1
1
1,5
294
800
360
-
film
3,6
LinocromeP
film
15х1
80
absolute
-
0
minus 15
-
1
1,5
294
800
360
2,7
film
4,6
LinocromeK
granulatedmaterial,
slate
10х1
80
-
absolute
0
minus 15
1
1
1,5
294
800
360
3,7
film
3,6
Linocrome Tropic P
film
10х1
120
absolute
-
minus 5
minus 15
-
1
1,5
294
800
400
2,7
film
4,6
Linocrome Tropic K
granulatedmaterial,
slate
10х1
120
-
absolute
minus 5
minus 15
1
1
1,5
294
800
400
3,7
film
TECHNONICOL MASTICS, SEALANTS AND PRIMERS
TECHNICAL SUPPORT AND INFORMATION ABOUT SALES OFFICES:Phone: +7 (495) 9255775, 8-800-200-05-65; Fax: +7 (495) 9258155
E-mail: [email protected] www.teplo.ru
Mastics, sealants, primers764
TECHNONICOL No.01 BITUMEN PRIMER
Priming is necessary for high-quality bonding of waterproofing materi-als to porous, rough and dusty surfaces. TECHNONICOL No.01 bitumen primer prepares (primes) surfaces to be insulated (concrete slabs, cement-and-sand screed) before you lay bonded/self-adhesive roofing and waterproofing materials.
The primer is a solution of high-quality oil bitumens with minimal melt-ing temperature of 80°C in specially selected dissolvents. The primer has high wetting capacity, penetrability and short drying time.
Application:Two classes of material are available:
• Ready-to-use primer applies on the basis immediately, which gives extra convenience and accelerates works.• Concentrated primer needs to be diluted before use, with any organ-ic diluters (petrol, white spirit, kerosene) in volume ratio of 1:1.5 – 1.2. It gives essential savings in use, shipment and storage.
We recommend applying TechnoNICOL bitumen primer onto the work-ing surface with capron brushes or paintbrushes. In this case the primer is smeared into the surface, saturates and strengthens it, which provides for the strong adhesion of the waterproofing with the base.
The coverage ratio of the diluted concentrate or ready-to-use primer is 250-350 ml/m2.
Technical specification TU 5775-011-17925162-2003
Physical-mechanical characteristics
Weight fraction of non-volatile substances (%) 35-40
10-30
Max. drying time at 20°C (hours)
+80
60-70
10-30
+80
Bitumen primer Bitumen primer (concentrate)
Relative viscosity (stokes, between)
Min. melting temperature (°C)
12 12
Mastics, sealants, primers 7 65
TECHNONICOL No.03 BITUMEN POLYMER PRIMERTECHNONICOL No.03 bitumen polymer primer is a solution of bitumen, polymers and adhesive additives in organic dissolvents. The material dries quickly and protects metal surfaces efficiently from corrosion be-fore waterproofing material is put. After waterproofing material is put, it increases cohesion between the bonded material and the substrate.
Application:• Cover steel orthotropic slabs of bridge spans before bonding protec-tion layer is put;• Cover other insulated surfaces before roofing and waterproofing ma-terials are put.
Technical specification TU 5775-042-17925162-2006
Physical-mechanical characteristicsWeight fraction of non-volatile matter (%, range)
Max. drying time at 20°C (minutes)
25-30
10-30Relative viscosity (stokes, between)
5
Mastics, sealants, primers766
TECHNONICOL No.04 BITUMEN-EMULSION PRIMER
It is used to prime cement-and-sand, concrete and other surfaces before you put bonded, self-adhesive roofing and waterproofing ma-terials.TECHNONICOL No.04 bitumen emulsion primer is bitumen dispersed in water. The coverage ratio of TECHNONICOL No.04 bitumen-emulsion primer is 250-350 ml/m2.The material is water-based, does not containdissolvents and is non-toxic.
Technical specification TU 5775-006-72746455-2007
Physical-mechanical characteristicsWeight fraction of non-volatile matter (%, range)
Max. drying time at 20°C (hours)
25-40
5-30Relative viscosity (stokes, between)
1
+75Min. melting temperature (°C)
Mastics, sealants, primers 7 67
TECHNONICOL No.21ROOFING MASTIC (TECHNOMAST)TECHNONICOL No.21 ROOF MASTIC is a ready-to-use material — oil bitumen modified by artificial rubber, mineral fillers and organic dissolvent. When it becomes dry, it forms a durable and flexible coating and considerably extends the service life of the protected sur-faces.
Application:• Arrange mastic roofs and repair all types of roofs;• Arrange waterproofing protection of struc-tures (foundations, basements, piles and oth-er items buried in soil or touching wet environ-ments);• Arrange waterproofing and anti-corrosion protection of metal surfaces including pipe-lines and car bodies.
Coatings based on TECHNONICOL No.21 roof mastic are highly adhesive to the base and can be used in the wide temperature range. TECHNONICOL No.21 roof mastic is applied onto the treated surface with a paint brush, putty knife or by pouring and leveling.
Technical specification TU 5775-018-17925162-2004
Physical-mechanical characteristicsMin. strength of bonding to base (MPa):
concrete
0,9 metal
Min. strength of bonding between layers (MPa):
0,6
0,3 roll material-roll material
0,4 roll material-concrete
4Min. adhesive bonding shear strength (kN/m)
1Min. nominal strength (MPa)
500Min. elongation at fracture (%)
0,4Min. water absorption within 24 hours (% by weight)
50Min. Weight fraction of non-volatile matter (%)
110Min. heat resistance (°C)
no fissuresFlexibility on a 5,0±0,2 mm bar at -50°C
satisfactoryWater impermeability within 24 hours at 0,1 MPa
Mastics, sealants, primers768
TECHNONICOL No.31ROOF EMULSION MASTIC
TECHNONICOL No.31 roof emulsion mastic is a ready-to use material — oil bitumen water emulsion, modified by artificial rubber, tech-nological additives and fillers. Coatings based on this product are highly elastic, provide high strength of bonding to the base, heat and moisture resistance. The material is water-based, does not contain dissolvents and is non-toxic.
Application:• Arrange smearing waterproof insulation of surfaces in premises (bathrooms, swimming pool floors, balconies, basements);• Arrange mastic roofs and repair all types of roofs (in combination with glass fiber fabric, roll materials or without them);• Arrange roof protection layers;• Waterproof structures (foundations, base-ments, piles and other items buried in soil or contacting wet environments).
Coverage ratio
Mastic roofs:
Waterproofing:
3,8 – 5,7 kg/m2
2,5 – 3,5 kg/m2
Technical specification TU 5775-042-17925162-2006
Physical-mechanical characteristicsMin. strength of bonding to concrete (MPa)
Min. nominal strength (MPa)
700Min. elongation at fracture (%)
Min. water absorption within 24 hours (% by weight)
0,5
50-70Richness of mix with emulsifier (% by weight, range)
95Min. heat resistance (°C)
no fissures Flexibility on a 5,0±0,2 mm bar at -15°C
satisfactoryWater impermeability within 24 hours at 0,1 MPa
0,45
1
ACCESSORIESFOR FLAT ROOFINGS
TECHNICAL SUPPORT AND INFORMATION ABOUT SALES OFFICES:Phone: +7 (495) 9255775, 8-800-200-05-65; Fax: +7 (495) 9258155
E-mail: [email protected] www.teplo.ru
Components and equipment870
ACCESSORIES FOR FLAT ROOFINGS
FastenersTechnoNICOL telescopic fastenersA telescopic fastener comprises a plastic element and a special anchor. The fastener fixes heat insulation elements, as well as roof membranes on the galvanized shaped sheet/wooden/solid-cast concrete and other bearing base. If the fasteners are used on profile metal decks, the self-tapping screws must have a tip bore. If the fasteners are fixed on con-crete, drive anchors should be used.
TechnoNICOL railsTechnoNICOL edge rails fix the edges of membrane roofing on the verti-cal surface. Not for use on bent surfaces. The strips are fixed on the base with self-tapping screws. The upper flanges should be filled with the edge sealant so as to ensure complete sealing and to prevent penetra-tion of moisture under the membrane. TechnoNICOL clamping rails fix the membrane along the roofing perimeter and around all outstanding structures. They are used on vertical surfaces where vertical and horizon-tal surfaces adjoin.
TechnoNICOL separating layerTo arrange a protective or a separating layer, glass fiber fabric and geo-textile are used. TechnoNICOL glass fiber fabric (min. 100 g/m2) is used as a separating layer between the PVC membrane and extruded polysty-rene; polyester fiber based layer (min. 70 g/m2) can also be used.
Welding equipmentThe complete offer of TechnoNICOL Corporation includes the entire range of the necessary welding equipment: Leister Triac Drive automatic welding equipment, Leister Triac portable welding machines and a set of heads.
Molded elements for PVC and TPO membranesMaterials prefabricated by molding of TPO or PVC pellets. These ele-ments do not have any reinforcement fibers or reinforcement mesh in-side, which makes it possible to change the shape of an element by heat-ing it and to make it fit the location where it is to be installed.
Water drainage systemsWater inlets are installed in lower locations. They are used to drain wa-ter from the roof. A special extension element ensures tight contact of vaporproofing and waterproofing layers. The heads may have bolted-on flanges or flanges made of the roofing material so as to be welded im-mediately to the membrane roofing. The intake holes may also be heat-ed. The underflow and overflow elements are used to drain water over the barrier wall. They can be made of PVC or TPP and are welded to the membrane roofing. The roof aerator removes steam from the roofing structure which reduces the moisture content in the insulant and other roofing layers.
Components and equipment 8 71
TechnoNICOL super-diffusion membraneThree-layer microporous membrane. The upper and the bottom layers are non-woven polypropylene fabrics. They form a rigid frame for the “working” interlayer. The interlayer is a polypropylene film. Due to its unique characteristics, it ensures the water steam diffusion and water resistance.
Optima TechnoNICOLsuper-diffusion membraneThree-layer microporous membrane with excellent quality-price ratio. This is a key material for heat-insulated roofs and stud walls of residen-tial cottages.
TechnoNICOL super-diffusion high-strength membraneThree-layer microporous membrane. Due to its durability, the mem-brane is an ideal solution for ventilated facades of high buildings and for pitched roofs. The membrane may serve as a temporary layer for protec-tion against sunlight, wind and precipitation for up to 4 months.
TechnoNICOL vapor insulation for flat roofsTechnoNICOL multilayer polyethylene flat roof vapor-proof film is used to protect roofs against steam from inside the premises. The product has excellent water- and vaporproofing characteristics, which minimizes penetration of water into the enclosures. It is laid on concrete decks or profile metal decks. The product is recommended for use in flat roofing systems.
TechnoNICOL butyl strip bondA strip bond is used for tight bonding of vapor-proof sheets, facade and under-roofing membranes, fixing of film edges on various bases and adjacent structures (pipes, fittings, antennas, etc.). Dimensions: 20x20x0.8mm. The strip bond is produced in Italy and complies with EU safety and environmental standards.
Components and equipment872
Physical-mechanical characteristics
TechnoNICOL super-diffusion
membrane
Length, m
Width, m 1,5
50
Density, g/m2
Number of rolls on pallet
MD tensile strength, N/5 cm
CD tensile strength, N/5 cm
MD elongation, %
CD elongation, %
Vapor impermeability, gr/(m2/day)
Water resistance, m w.c.
Resistance to UV light, months
170
160
60
22
3
1100
60
TechnoNICOL optima super-diffu-
sion membrane
1,5
50
230
180
70
22
4
1000
60
TechnoNICOL high-strength super-diffusion
membrane
1,5
50
290
230
60
22
4
1000
60
TechnoNICOL vapor insulation for flat
roofings
3
30
160
170
919
21
1
1,11
720
85 110 150 120
56 42 30 150
At customer’s request, the membranes can be supplied on pallets. The shipment is made for free if the vehicle is fully loaded with these or other materials from TechnoNICOL Corporation. Complex shipments of heat insulations and water-proofing materials from TechnoNICOL save your money and time.
8 73
PRODUCTION OF ROOFING AND WATERPROOFING MTERIALSVoskresensk (Moscow Region) TechnoNICOL Voskresensk LLC; Phone: +7 (48999) 48 993Vyborg, TechnoNICOL Vyborg; Phone: 7 (81378) 390 90Mineralniye Vody, Minvody Krovlia LLC Plant; Phone: +7 (87922) 76 818Murom, Muromskiy KRZ LLC; Phone: +7 (49234) 22 045Nizhniy Nvgorod, NRRZ LLC; Phone: +7 (8312) 41 69 62Novoulianovsk, Tekhnokrom LLC Plant; Phone: +7 (84255) 71 208Rybinsk, Kroma LLC Plant; Phone: +7 (4855) 26 61 50Ryazan, Technoflex Plant LLC; Phone: +7 (4912) 911 291Uchaly, TECHNOPLEX Plant LLC; Phone: +7 (34791) 413 68Phone: Yugra, TechnoNICOL Siberia LLC Plant; Phone: +7 (38451) 498 32Lithuania, UAB Gargzdu MIDA; Phone: +3 70 46 397 337Ukraine, Dneprodzerzhinsk, TechnoNICOL Plant LLC; Phone: +38 (0569) 55 30 00 Republic of Belarus, Asipovic’y, JV OJSC Krovlia; Phone: +375 (2235) 22 477
PRODUCTION OF WATERPROOFING POLYMER MEMBRANESRyazan, Logicroof Plant LLC; Phone: +7 (4912) 91 13 52
PRODUCTIN OF STONE WOOLCheliabinsk, AKSI OJSC; Phone: +7 (351) 799 35 80Ryazan, TECHNO Plant LLC; Phone: +7 (4912) 91 12 53Zainsk, TECHNO Plant LLC; Phone: +7 (85558) 5 86 00Khabarovsk, Bazalit DV OJSC; Ryazan, TECHNO Plant; Phone: +7 (4212) 52 25 53Yugra, TECHNO Plant LLC; Phone: +7 (38451) 49838Cherkassy, TECHNO Plant LLC; Phone: +38 (0472) 719797
PRODUCTION OF EXTRUDED FOAM PLYSTYRENERyazan, TECHNOPLEX Plant LLC; Phone: +7 (4912) 911 444 Uchaly, TECHNOPLEX Plant LLC; Phone: +7 (34791) 41 318Yugra, TECHNOPLEX Plant LLC; Phone: +7 (38451) 498 52 Mineralniye Vody, TECHNOPLEX Plant LLC; Phone: +7 (87922) 445 71 Novoulianovsk, TECHNOPLEX Plant LLC; Phone: +7 (84255) 738 97 Dneprodzerzhinsk, TECHNOPLEX Plant LLC; Phone: + 38 (0569) 785 20 77
PRODUCTION OF SHINGLAS FLEXIBLE ROOF TILESLithuania, UAB Gargzdu MIDA; Phone +3 70 46 97 73 37 Ryazan, SHINGLAS Plant LLC +7 (4912) 9112 21
PRODUCTION OF LUXARD FLEXIBLE ROOF TILESVoskresensk, Luxard Plant LLC; Phone: +7 (495) 232 53 59
PRODUCTION OF MASTICSNovoulianovsk, Technokrom Plant LLC; Phone: +7 (84255) 71 208 Vyborg, TechnoNICOL Vyborg LLC; Phone: +7 (81378) 39090 Uchaly, TECHNOPLEX Plant LLC; Phone: +7 (34791) 41 318Voskresensk (Moscow Region) TechnoNICOL Voskresensk LLC; Phone: +7 (48999) 48 993Mineralniye Vody, Minvody Krovlia LLC Plant; Phone: +7 (87922) 76 818 Republic of Belarus, Osipovichi, JV OJSC Krovlia; Phone: + 37 (52235) 22 477
PRODUCTION OF GLASS FIBERVoskresensk (Moscow Region), NICOglass Plant; Phone: +7 (49644) 48 996
PRODUCTION OF COMPONENTS FOR ROOFINGS AND EQUIPMENTVoskresensk (Moscow Region), Engineering Workshops; Phone: +7 (49644)59 666