Cisco CMD line vs Dell CMD Line
CMD available on Cisco IOS and
Dell OS6 and Dell OS9
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
CLI prompts console>en
console#conf
console(config)#
Dell>en
Dell#conf
Dell(conf)#
Switch>en
Switch#config t
Switch(config)#
Same
Show commands console#show ?
console#show version
console#show system
console#show interfaces status
console#show interfaces detail gi1/0/1
console#show running-config
console#dir
console#show mac address-table
console#show vlan
Dell#show ?
Dell#show version
Dell#show inventory
Dell#show environment
Dell#show interfaces
Dell#show interfaces status
Dell#show interface ma0/0
Dell#show interface te0/1
Dell#show running-config
Dell#dir
Dell#show mac-address-table
Dell#show vlan
Switch#show?
Switch#version
Switch#system
Switch#show int Ethernet
Switch#show int mgmt-ethernet
Switch#show running-config
Switch#dir
Switch#show mac-address-table
Switch#show vlan
95% same
copy run start console#copy running-config startup-config
console#write memory
console#reload
Dell#copy running-config startup-config
Dell#write memory
Dell#reload
Switch#copy running-config startup-
config
Switch#write memory
Switch#reload
Same
delete startup-
config
Dell#delete startup-config Switch#erase startup-config
or delete nvram
Cisco
different
hostname console(config)#hostname xxxxxxx Dell(conf)#hostname xxxxxxx
(any character: a-z, numbers, special)
Switch(config)#hostname xxxxxxx Same
banner console(config)#banner motd "Happy New
Year"
Dell(conf)#banner motd c Happy New Year
c
Switch(config)#banner motd # Happy
New Year #
Same
syntax,
different
variable
enable password console(config)#enable password xxxxx Dell(conf)#enable password xxxxx Switch(config)#enable password xxxxx Same
username/
password
console(config)#username xxx password xxx
privilege 15
Dell(conf)#username xxx password xxx
privilege 15
Switch(config)#username xxx password
xxx privilege 15
Same
aaa authentication console(config)#aaa authentication login
default local line
Dell(conf)#aaa authentication login default
local line
Switch(config)#aaa (name)
Switch(config)#aaa authentication
login default
Switch(config)#line vty 0 4
Same
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
Switch(config)#login auth (name)
Telnet access console(config)#no ip telnet server disable
console(config)#enable password password
encrypted
console(config)#aaa authentication login
“loc” local line
console(config)#line telnet
console(config-telnet)#login authentication
loc
console(config-telnet)#exit
console(config)#enable password password
console(config)#username xxxx password
password
Dell(conf)#ip telnet server enable
Dell(conf)#enable secret password
Dell(conf)#aaa authentication login default
local line
Dell(conf)#line vty 0 4
Dell(conf-line-vty)#password password
Dell(conf)#username xxxx password
password
Switch(config)#line con 0
Switch(config-line)#password letmein
Switch(config-line)#login
Switch(config)#username joe password
fishing
Switch(config)#username jane
password Bombay
Switch(config)#line vty 0 4
Switch(config-line)#login local
Switch(config)#aaa (name)
Switch(config)#aaa authentication
login my-auth-list tacacs+
Switch(config)#tacacs-server host
x.x.x.x/y
Switch(config)#tacacs-server key
password
Similar
Management VLAN console(config)#vlan x
console(config-vlanx)# vlan association
subnet ip_addr subnet_mask
console(config-vlanx)#no shut
Dell(conf)#interface vlan x
Dell(conf-if-vl-x)#ip address x.x.x.x/y
Dell(conf-if-vl-x)#no shut
Switch(config)#int gig 0/1
Switch(config-if)#switchport access
vlan 9
Switch(config-if)#switchport mode
trunk
Switch(config)#interface vlan 9
Switch(config-vlan)#ip address
192.168.1.9 255.255.255.0
Switch(config)#ip default-gateway
192.168.1.254
Similar
OOB management console(config)#interface out-of-band
console(config-if)#ip address x.x.x.x/y
console(config-if)#no shut
Dell(conf)#interface management0/0
Dell(conf-if-ma-0/0)#ip address x.x.x.x/y
Dell(conf-if-ma-0/0)#no shut
Switch(config)# interface mng 0/1
Switch(config-if)#ip 192.168.1.100
255.255.255.0
Switch(config-if)#no shut
Same
except int
name
L3 port IP address may only be assigned to a
loopback, VLAN or tunnel
Dell(conf)interface te0/x
Dell(conf-if-te-0/x)#ip address x.x.x.x/y
Dell(conf-if-te-0/x)#no shut
Switch(config)#interface te1/0/x
Switch(config-if)# ip address x.x.x.x/y
Switch(config-if)#no shut
OS 6
different
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
Line authentication console(config)#no ip telnet server disable
console(config)#enable password Dellsvcs2
encrypted
console(config)#aaa authentication login
TELNET line local
console(config)#line telnet
console(config-telnet)#password Dellsvcs5
console(config-telnet)# login authentication
TELNET
console(config)#int te1/0/2
console(config-if-Te1/0/2)#ip address
192.168.33.2/24
console(config-if-Te1/0/2)#no shut
Using telnet line:
console>telnet 192.168.33.4
Password: ********* (line vty pswd)
console2>enable
Password: ********* (enable secret pwd)
console2#
Dell(conf)#ip telnet server enable
Dell(conf)#enable secret Dellsvcs2
Dell(conf)#aaa authentication login
TELNET line local
Dell(conf)#line vty 0 4
Dell(conf-line-vty)#password Dellsvcs5
Dell(conf-line-vty)# login authentication
TELNET
Dell(conf)#int gi0/2
Dell(conf-if-gi-0/2)#ip address
192.168.33.2/24
Dell(conf-if-gi-0/2)#no shut
Using telnet line:
Dell>telnet 192.168.33.4
Password: ********* (line vty pswd)
Dell2>enable
Password: ********* (enable secret
pwd)
Dell2#
Switch(config)#feature telnet
Switch(config)#enable secret iossvcs2
Switch(config)#aaa authentication
login TELNET line local
Switch(config)#line vty 0 4
Switch(config-line-vty)#password
iossvcs5
Switch(config-line-vty)#login
authentication TELNET
Switch(config)#int gi1/0/2
Switch(config-if-gi-1/0/2)#ip address
192.168.33.2/24
Switch(config-if-gi-1/0/2)#no shut
Using telnet line:
Switch>telnet 192.168.33.4
Password: ********* (line vty pswd)
Switch2>enable
Password: ********* (enable secret
pwd)
Switch2#
Similar
Local
authentication
(default)
console(config)# no ip telnet server disable
console(config)#enable password Dellsvcs2
encrypted
console(config)#line telnet
console(config-telnet)#aaa authentication
login TELNET1 local line
console(config)#username admin password
Dellsvcs3
console(config)#line telnet
console(config-telnet)# login authentication
TELNET1
console(config)#int te1/0/2
console(config-if-Te1/0/2)#ip address
192.168.33.2/24
Dell(conf)#ip telnet server enable
Dell(conf)#enable secret Dellsvcs2
Dell(conf-line-vty)#aaa authentication login
TELNET1 local line
Dell(conf)#username admin password
Dellsvcs3
Dell(conf)#line vty 0 4
Dell(conf-line-vty)# login authentication
TELNET1
Dell(conf)#int gi0/2
Dell(conf-if-gi-0/2)#ip address
192.168.33.2/24
Dell(conf-if-gi-0/2)#no shut
Switch(config)#ip telnet server enable
Switch(config)#enable secret
p@ssw0rd
Switch(config-line-vty)#aaa
authentication login TELNET1 local line
Switch(config)#username admin
password iossvcs3
Switch(config)#line vty 0 4
Switch(config-line-vty)# login
authentication TELNET1
Switch(config)#int gi1/0/2
Switch(config-if)#ip address
192.168.33.2/24
Switch(config-if)#no shut
Similar
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
console(config-if-Te1/0/2)#no shut
Using telnet local:
console>telnet 192.168.33.2
Login: admin
Password: ****** (admin's pswd)
console2>enable
Password: ****** (enable secret pswd)
console2#
Using telnet local:
Dell>telnet 192.168.33.2
Login: admin
Password: ****** (admin's pswd)
Dell2>enable
Password: ****** (enable secret pswd)
Dell2#
Using telnet local:
Switch>telnet 192.168.33.2
Login: admin
Password: ****** (admin's pswd)
Switch2>enable
L2 switchport console(config)#interface te1/0/2
console(config-if-Te1/0/2)#no ip address
<switchport enabled by default>
Dell(conf)#interface te0/2
Dell(conf-if-te-0/2)#no ip address
Dell(conf-if-te-0/2)#switchport
Dell(conf-if-te-0/2)#no shutdown
Switch(config)#interface te1/0/2
Switch(config-if)#no ip address
Switch(config-if)#switchport
Switch(config-if)#no shutdown
Same
mac-address-table console#show mac address-table Dell#show mac-address-table Switch#show mac address-table OS 9
different
Port security MAC learning limit:
console(config)#int te1/0/2
console(config-if-Te-0/2)#port security max 2
console(config-if-Te-0/2)#port security
discard
Static MAC entry:
console(config)#mac-address-table static
xx:xx:xx:xx:xx:xx vlan x interface te1/0/2
MAC learning limit:
Dell(conf)#int gi0/2
Dell(conf-if-gi-0/2)#mac learning-limit 2
Dell(conf-if-gi-0/2)#mac learning-limit
learn-limit-violation shutdown
Static MAC entry:
Dell(conf)#mac-address-table static
xx:xx:xx:xx:xx:xx output gi0/x vlan x
MAC learning limit:
Switch(config)#int gi1/0/2
Switch(config-if)#switch port port-
security maximum(10)
Switch(config-if)#switchport port-
securty violation shutdown
Static MAC entry:
Switch(config)#int gi1/0/2
Switch(config-if)#switchport port-
security mac-address xx:xx:xx:xx:xx:xx
Similar
Create VLAN console(config)#vlan 11
console(config-vlan11)#name Sales
console(config-vlan11)#exit
console(config)#interface vlan 11
console(config-if)#ip address ww.xx.yy.zz /XX
console#show vlan
Dell(conf)#interface vlan 11
Dell(conf-if-vl-11)#description Sales
Dell(conf-if-vl-11)#interface vlan 22
Dell(conf-if-vl-22)#description Voice
Dell(conf-if-vl-22)#interface vlan 33
Dell(conf-if-vl-33)#description IT
Dell#show vlan
Switch#vlan database
Switch(vlan)#vlan 11
Switch(vlan)#vlan 10
Switch(vlan)#exit
Switch#show vlan
Similar
(no vlan
database in
OS 6/9)
Add interface to
VLAN
console(config)#interface te1/0/3
console(config-if)#switchport mode access
Dell(conf)#interface vlan 33
Dell(conf-if-vl-33)#untagged gi 0/2
Switch(config)#interface gig0/5 OS 9
different
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
(access |
untagged)
console(config-if-Te1/0/3)#switchport
access vlan 33
Switch(config-if)#switchport mode
access
Switch(config-if)switchport access vlan
10
Add interface to
VLAN (trunk |
tagged)
console(config-if-Te1/0/3)#switchport
access vlan 11
console(config-if-Te1/0/3)#switchport
access vlan 22
console(config)#int te1/0/3
console(config-if-Te1/0/3)#switchport mode
trunk
console(config-if-Te1/0/3)#switchport trunk
allowed vlan add 11,22,33
console#show vlan
console#show interfaces status
Dell(conf)#int te0/3
Dell(conf-if-te-0/3)#switchport
Dell(conf-if-te-0/3)#no shut
Dell(conf-if-te-0/3)#interface vlan 11
Dell(conf-if-vl-11)#tagged te0/3
Dell(conf-if-vl-11)#interface vlan 22
Dell(conf-if-vl-22)#tagged te0/3
Dell(conf-if-vl-22)#interface vlan 33
Dell(conf-if-vl-33)#tagged te0/3
Dell#show vlan
Switch(config)#int te0/3
Switch(config-if)#switchport trunk
encapsulation dot1q
Switch(config-if)#switchport mode
trunk
Switch(config-if)#switchport trunk
allowed vlan remove 1-4,6
Switch(config-if)#switchport trunk
allowed vlan 5,7-10
Switch#show interfaces vlan trunk
OS 9
different
Hybrid mode
(switchport mode
general | portmode
hybrid)
console(config)#interface te1/0/1
console(config-if-Te1/0/1)#switchport mode
general
console(config-if-gi1/0/1)# switchport access
vlan 11,22
console#show interfaces status
Dell(conf)#interface te0/1
Dell(conf-if-Te-0/1)#portmode hybrid
Dell(conf-if-Te-0/1)#switchport
Dell(conf-if-Te-0/1)#interface vlan 11
Dell(conf-if-vl-11)#untagged te0/1
Dell(conf-if-vl-11)#interface vlan 22
Dell(conf-if-vl-22)#tagged te0/1
Dell#show vlan
Switch(config)#interface te0/1
Switch(config-if)#port link-type hybrid
Switch(config-if)#port hybrid vlan 20 30
tagged
Switch(config-if)#port hybrid vlan 10
untagged
Switch(config-if)#port hybrid pvid vlan
10 (sets default vlan)
Switch#show vlan
Similar
Layer 3 VLAN console(config)# ip routing
console(config)#interface vlan 11
console(config-if)#ip address
192.168.11.254 /24
console(config-vlan11)#exit
console(config)#
console#show ip route
Dell(conf)#int vlan 11
Dell(conf-if-vl-11)#ip address
192.168.11.254/24
Dell(conf-if-vl-11)#no shut
Dell(conf-if-vl-11)#int vlan 33
Dell(conf-if-vl-33)#ip address
192.168.33.254/24
Dell(conf-if-vl-33)#no shut
Dell#show ip route
Switch#vlan database
Switch(vlan)#vlan 11
Switch(vlan)#vlan 10
Switch(vlan)#exit
Switch#interface vlan 10
Switch(config-if)#ip address x.x.x.x.x/y
Switch(config-if)#no shut
Switch#show ip route
Similar
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
Spanning Tree
Protocols
STP-PV, RSTP-PV, MSTP
STP-PV
Console(config)# spanning-tree mode stp-
pvst
Console(config)#spanning-tree vlan 30-32
priority 1
Console(config)#Spanning-tree vlan 33-35
priority 4096
RSTP-PV
Console(config)#spanning-tree mode rapid-
pvst
Console(config)#spanning-tree vlan 30-32
priority 1
Console(config)#Spanning-tree vlan 33-35
priority 4096
MSTP
Console-1(config)#spanning-tree mst
configuration
console-1(config-mst)#instance 1 add vlan
30-32
console-1(config-mst)#instance 2 add vlan
33-35
console-1(config-mst)#name Region1
console-1(config-mst)#revision 1
console-1(config-mst)#exit
console-1(config)#spanning-tree mst 1 priority
4096
console-1(config)#spanning-tree mst 2 priority
16384
console-1(config)#spanning-tree mode mst
console-1(config)#exit
STP, RSTP, MSTP, PVST+
STP
Dell(conf)#spanning-tree stp
Dell(conf-stp)#bridge priority 4096
Dell(conf-stp)#No disable
RSTP
Dell(conf)#spanning-tree rstp
Dell(conf-rstp)#bridge priority 4096
Dell(conf-rstp)#No disable
MSTP
Dell(conf)#spanning-tree mstp
Dell(conf-mstp)#no disable
Dell(conf-mstp)#msti 1 vlan 5 - 10
Dell(conf-mstp)#msti 1 bridge-priority 4096
Dell(conf-mstp)#name <name>
Dell(conf-mstp)#revision <number>
PVST+
Dell(config)#protocol Spanning-tree pvst
Dell(config-pvst)#vlan 2 bridge priority
4096
Dell(config-pvst)#vlan 3 bridge priority
16384
STP, PVST+, RPVST+, MSTP
STP
Enabled out of the box.
Switch(config)#
PVST+
Switch(config)#spanning-tree vlan 1
root primary
Switch(config)#spanning-tree vlan 10
root primary
RPVST+
Switch(config)#spanning-tree mode
rapid-pvst
No additional vlan info required
MSTP
switch(config)#spanning-tree mode mst
switch(config)#spanning-tree mst 0
priority 4096
switch(config)#spanning-tree mst
configuration
switch(config-mst)#name Region1
switch(config-mst)#revision 1
switch(config-mst)#instance 1 vlan 30-
32
switch(config-mst)#instance 2 vlan 33-
35
switch(config-mst)#end
For across-
the-board
interop, use
RSTP or
MSTP. For
Cisco
PVST+
compatibilit
y OS
6=RSTP-PV,
OS 9 =
PVST+
Port Channel/static console(config)#int range te1/0/4-10 Dell(conf)#interface range te0/11-18 Switch(conf)#interface port-channel 22 Similar
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
console(config-range-if)#channel-group 22
mode on
Dell(conf-if-range-te-0/11-18)#no shut
Dell(conf)#int po22
Dell(conf-if-po-22)#channel-member
te0/11-18
Dell(confi-if-po-22)#switchport
Dell(confi-if-po-22)#no shut
Switch(conf-if)#no switchport
Switch(conf-if)#ip address x.x.x.x./y
Switch(conf-if)#interface range gi 0/11-
18
Switch(confi-if)#no ip address
Switch(confi-if)#channel group 22
mode desirable
Port Channel
dynamic
console(config)#int range te1/0/4-10
console(config-range-if)#channel-group 22
mode active
Cannot assign an IP address to a port-
channel in OS 6.
Dell(conf)#interface te0/11-18
Dell(conf-if-te-0/11-18)#no shut
Dell(conf-if-te-0-11-18)#port-channel-
protocol lacp
Dell(conf-if-te-0/11-18-lacp)#port-channel
22 mode active
Dell(conf)#int po22
Dell(conf-if-po-22)#switchport
Dell(conf-if-po-22)#no shut
Switch(conf)#interface port-channel 22
Switch(conf-if)#no switchport
Switch(conf-if)#ip address x.x.x.x./y
Switch(conf-if)#interface range gi 0/11-
18
Switch(confi-if)#no ip address
Switch(confi-if)#channel group 22
mode active
Similar
Loopback console(config)#int loopback 0
console(config-if-loopback0)#ip address
xx.xx.xx.xx/yy
Dell(conf)#int loopback 0
Dell(conf-if-lo-0)#ip address xx.xx.xx.xx/yy
Dell(conf-if-lo-0)#no shutdown
Switch(config)#interface Ethernet 0
Switch(config-if)#loopback (variable)
Same
Null console(config-route-map)#set interface
null0
Dell(conf)#int null 0
Dell(conf-if-nu-0)# ip unreachables
Switch(config)#int null 0
Switch(config-if)# ip unreachables
OS 6
different
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
mLAG/VLT/ vPC mLAG
DCPDP (Dual Control Plane Detection
Protocol) is intended to provide a secondary
layer of protection against peer link failures.
Console - VPC domain
console#configure
console(config)#vpc domain 1
console(config-vpc 1)#role priority 50
console(config-vpc 1)#peer-keepalive enable
console(config-vpc 1)#peer-keepalive
destination 192.168.1.X source 192.168.1.Y
console(config-vpc 1)#peer detection enable
console(config-vpc 1)#end
Console2 - VPC domain
console#configure
console(config)#vpc domain 1
console(config-vpc 1)#role priority 250
console(config-vpc 1)#peer-keepalive enable
console(config-vpc 1)#peer-keepalive
destination 192.168.1.Y source 192.168.1.X
console(config-vpc 1)#peer detection enable
console(config-vpc 1)#end
Console & Console 2 - Port-channels for
MLAG peer links
VLT
RSTP backup to VLT (best practice)
Dell(conf)#protocol spanning-tree rstp
Dell(conf-rstp)#no disable
Dell & Dell2 - backup link (best practice -
use ma0/0)
Dell(conf)#int te0/10
Dell(conf-if-te-0/10)#no switchport
Dell(conf-if-te-0/10)#ip address
10.12.2.1/24
Dell(conf-if-te-0/10)#no shut
Dell & Dell 2 - Static Po for VLTi
Dell(conf)#int range te0/21 , te0/22
Dell(conf-if-range-te-0/21,te-
0/22)#switchport
Dell(conf-if-range-te-0/21,te-0/22)#no
shut
Dell(conf)#interface port-channel 100
Dell(conf-if-po-100)#channel-member
te0/21-22
Dell(conf-if-po-100)#no shut
Dell - VLT domain
vPC
Cisco (config mgmt. interface)
Switch-1(config)# int mgmt 0
Switch-1(config-if)# ip address
172.25.182.51/24
Switch-1(config-if)# vrf context
management
Switch-1(config-vrf)# ip route 0.0.0.0/0
172.25.182.1
Enable vPC and LACP
Switch-1(config)# feature vpc
Switch-1(config)# feature lacp
Create VLAN
Switch-1(config)#vlan 101
Cisco/OS 6
very similar,
OS 9,
slightly
different
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
console#configure
console#interface port-channel 1
console(config-if-Po1)#description MLAG-
PEER-LINK
console(config-if-Po1)#spanning-tree disable
console(config-if-Po1)#switchport mode trunk
console(config-if-Po1)#vpc peer-link
console(config-if-Po1)#exit
console(config)#interface range te1/0/4-5
console(config-if)#channel-group 1 mode
active
console(config-if)#description MLAG-PEER-
LINK
console(config-if)#no shutdown
Console & Console 2 - dynamic peer-lags
console(config-if)# int te1/0/11
console(config-if-Te1/0/11)#channel-group 2
mode active
console(config-if-Te1/0/11)#no shut
console(config-if-Te1/0/11)#exit
console(config)#Int port-channel 2
console(config-if-Po2)#switchport mode trunk
console(config-if-Po2)#vpc 2
console(config-if-Po2)#no shut
console(config-if-Po2)#end
Console & Console 1 -
Enable MLAG globally
Console(config)#feature vpc
Dynamic LAG from downstream switch
console3(config-if)#interface range te
1/0/10-11
console3(config-if)#channel-group 2 mode
active
console3(config-if)#no shutdown
console3(config-if)#exit
Dell(conf)#vlt domain 100
Dell(conf-vlt-domain)#back-up destination
10.12.2.2
Dell(conf-vlt-domain)#peer-link port-
channel 100
Dell(conf-vlt-domain)#primary-priority 1
Dell(conf-vlt-domain)#unit-id 0
Dell(conf-vlt-domain)#exit
Dell2 - VLT domain
Dell2(conf)#vlt domain 100
Dell2(conf-vlt-domain)#back-up destination
10.12.2.1
Dell2(conf-vlt-domain)#peer-link port-
channel 100
Dell2(conf-vlt-domain)#primary-priority 2
Dell2(conf-vlt-domain)#unit-id 1
Dell2(conf-vlt-domain)#exit
Dell & Dell2 - dynamic peer-lags
Dell(conf)#interface te0/4
Dell(conf-if-te-0/4)#no shut
Dell(conf-if-te-0/4)#port-channel-protocol
lacp
Dell(conf-if-te-0/4-lacp)#port-channel 21
mode active
Dell(conf)#int po21
Dell(conf-if-po-21)#switchport
Dell(conf-if-po-21)#vlt-peer-lag port-
channel 21
Dell(conf)#interface te0/11
Dell(conf-if-te-0/11)#no shut
Dell(conf-if-te-0-11)#port-channel-protocol
lacp
Dell(conf-if-te-0/11-lacp)#port-channel 22
mode active
Dell(conf)#int po22
Dell(conf-if-po-22)#switchport
Create vPC domain
Switch-1(config)# vpc domain 1
Create vPC role pri (optional)
Switch-1(config-vpc-domain)# role
priority 1000
Configure the peer keep alive link. The
management interface IP address
Switch 2 is 172.25.182.52.
Switch-1(config-vpc-domain)# peer-
keepalive destination 172.25.182.52
Configure vPC peer link
Switch-1(config-vpc-domain)# int
ethernet 1/17-18
Switch-1(config-if-range)# channel-
group 1 mode active
Switch-1(config-if-range)# int po1
Switch-1(config-if)# vpc peer-link
Switch-1(config-if)# switchport mode
trunk
Switch-1(config-if)# switchport trunk
allowed vlan 1,101
Configure Switch 2
Switch-2(config)# int mgmt 0
Switch-2(config-if)# ip address
172.25.182.52/24
Switch-2(config-if)# vrf context
management
Switch-2(config-vrf)# ip route 0.0.0.0/0
172.25.182.1
Switch-2(config)# feature vpc
Switch-2(config)# feature lacp
Switch-2(config)#vlan 101
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
console3(config)#interface port-channel 2
console3(config-if-Po2)#switchport mode
trunk
console3(config-if-Po2)#end
console#show vpc brief
Dell(conf-if-po-22)#vlt-peer-lag port-
channel 22
(Add dynamic LAGs from downstream
switches)
Dell#show vlt brief
Dell#show vlt detail
Dell#show spanning-tree rstp brief
Switch-2(config)# vpc domain 1
Switch-2(config-vpc-domain)# peer-
keepalive destination 172.25.182.51
Mgmnt VRF will be used as the default
VRF
Switch-2(config-vpc-domain)# int
ethernet 1/17-18
Switch-2(config-if-range)# channel-
group 1 mode active
Switch-2(config-if-range)# int po1
Switch-2(config-if)# vpc peer-link
Switch-2(config-if)# switchport mode
trunk
Switch-2(config-if)# switchport trunk
allowed vlan 1,101
Switch-2(config-if)# int ethernet
100/1/1
Switch-2(config-if)# channel-group 10
Switch-2(config-if)# int po10
Switch-2(config-if)# vpc 10
Switch-2(config-if)# switchport access
vlan 101
Static Routing console(config)#ip route 1.1.1.0 /24 1.1.1.1
OS 6 cannot route to an interface.
Dell(conf)#ip route 1.1.1.0/24 te0/4
Dell(conf)#ip route 1.1.1.0/24 te0/4
Dell(conf)#ip route 2.2.2.0/24 te0/4
Dell(conf)#ip route 3.3.3.0/24 te0/4
Dell(conf)#ip route 4.4.4.0/24 te0/4
OS 6
different
Default Route console(config)#ip route default
192.168.112.2
Dell(conf)#ip route 0.0.0.0/0 te0/4 Dell(conf)#ip route 0.0.0.0/0 te0/4 OS 6
different
VRRP/HSRP
console(config)#int te1/0/3
console(config-if-Te1/0/3)#vrrp 1
console(config-if-Te1/0/3)# vrrp 10 ip
192.168.123.254
Dell(conf)#int te0/3
Dell(conf-if-te-0/3)#vrrp-group 1
Dell(conf-if-te-0/3-vrid-1)#virtual-address
192.168.123.254
Steps to enable HSRP
Switch(config)# interface
gigabitethernet0/1
Switch(config-if)# standby 1 ip
Similar. IOS
supports
both HSRP
(proprietary
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
console(config)#int te1/0/8
console(config-if-Te1/0/8)#vrrp 1
console(config-if-Te1/0/8)# vrrp 10 ip
192.168.123.254
console(config)#int te1/0/3
console(config-if-Te1/0/3)#vrrp 1
console(config-if-Te1/0/3)#vrrp 10 ip
192.168.223.254
console(config)#int te1/0/8
console(config-if-Te1/0/8)#vrrp 1
console(config-if-Te1/0/8)# vrrp 10 ip
192.168.223.254
console#sh vrrp
console#sh vrrp brief
Set VRRP priority manually
console(config-if-Te1/0/8)#vrrp 1 priority
200
Set VRRP authentication
console(config-if-Te1/0/8)# vrrp 1
authentication simple 0 dell
console2(config-if-Te1/0/8)# vrrp 1
authentication simple 0 dell
VRRP interface tracking
console(config-if-te1/0/6)# vrrp 10 track
interface te1/0/10
Dell(conf)#int te0/8
Dell(conf-if-te-0/8)#vrrp-group 1
Dell(conf-if-te-0/8-vrid-1)#virtual-address
192.168.123.254
Dell2(conf)#int te0/3
Dell2(conf-if-te-0/3)#vrrp-group 1
Dell2(conf-if-te-0/3-vrid-1)#virtual-address
192.168.223.254
Dell2(conf)#int te0/8
Dell2(conf-if-te-0/8)#vrrp-group 1
Dell2(conf-if-te-0/8-vrid-1)#virtual-address
192.168.223.254
Dell#show vrrp
Dell#show vrrp brief
Set VRRP priority manually
Dell(conf-if-te-0/8)#vrrp-group 1
Dell(conf-if-te-0/8-vrid-1)#priority 200
Set VRRP authentication
Dell(conf-if-te-0/8-vrid-1)# authentication-
type simple 0 dell
Dell2(conf-if-te-0/3-vrid-1)# authentication-
type simple 0 dell
VRRP interface tracking
Dell(conf-if-te-0/6-vrid-1)#track te 0/10
priority-cost 110
Switch(config-if)# end
Switch# show standby
Configure HSRP Priority
Switch(config)# interface
gigabitethernet0/1
Switch(config-if)# standby ip
172.19.108.254
Switch(config-if)# standby priority 120
preempt delay 300
Configure HSRP Auth and Timers
Switch(config)# interface
gigabitethernet0/1
Switch(config-if)# standby 1
authentication word
Standby Group 1
Switch(config)# interface
gigabitethernet0/1
Switch(config-if)# standby 1 ip
Switch(config-if)# standby 1 timers 5
15
Configure HSRP Groups and Clustering
Switch(config)# cluster standby-group
my_hsrp routing-redundancy
) and VRRP
(open
standard)
Stacking console(config)#switch 1 renumber 2
Renumbering forces a reload.
console(config-stack)#stack
Dell#stack-unit 0 renumber 2
Renumbering management unit will reload
the stack. Warning: Interface configuration
for current unit will be lost!
Proceed to renumber [confirm yes/no]:yes
Assign stack number or renumber
Switch(config)# current-stack-member-
number 2 renumber new-stack-
member 1
Switch#copy run start
Similar
OS 6/9:
depending
on the
model use
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop
console(config-stack)#standby 2
console(config-stack)#stack-port
tengigabitethernet 2/0/24 stack
console(config-stack)#boot auto-copy-sw
console(config-stack)#exit
console(config)#reload
%STKUNIT0-M:CP %IFMGR-1-DEL_PORT:
Removed port: Te 0/0-47, Fo
0/48,52,56,60
System configuration has been modified.
Save? [yes/no]:yes
NOTE: The switch reboots.
Dell(conf)#stack-unit 2 priority 1
Dell(conf)#stack-unit 2 stack-group xx
Setting ports Fo 2/yy as stack group will
make their interface configs obsolete after
a reload. [confirm yes/no]:yes
%STKUNIT1-M:CP %IFMGR-6-
STACK_PORTS_ADDED: Ports Fo 2/yy have
been configured as stacking ports. Please
save and reload for config to take effect.
Press Enter
NOTE: Wait to save/reload switch until
after configuring
the second stack group.
switch(conf)#stack-unit 2 stack-group xx
Setting ports Fo 2/yy as stack group will
make their interface configs obsolete after
a reload. [confirm yes/no]:yes
%STKUNIT1-M:CP %IFMGR-6-
STACK_PORTS_ADDED: Ports Fo 2/yy have
been configured as stacking ports.
Please save and reload for config to take
effect.
Press Enter
switch(conf)#exit
Dell#copy run start
Dell#reload
Proceed with reload [confirm yes/no]:yes
NOTE: After reload, prompt will change to
Dell(stack-member-2)>
Switch#reload
Switch(config)#stack-member-number
0 priority 15
Switch#copy run start
Switch#reload
Switch(config)# current-stack-member-
number 6 renumber new-stack-
member 2
Switch#copy run start
Switch#reload
Switch(config)#stack-member-number
0 priority 10
Switch#copy run start
Switch#reload
Switch(config)# current-stack-member-
number 0 renumber new-stack-
member 3
Switch#copy run start
Switch#reload
Switch(config)#stack-member-number
0 priority 5
Switch#copy run start
Switch#reload
After final reload there should be three
switches in one stack.
Config configuration
Switch#show switch stack-ports
summary
stacking
module or
user data
ports for
stacking.
Feature Dell Networking OS 6 Dell Networking OS 9 Cisco IOS Interop