Close end tube (Pipe) type thermowell Model : A500, A510 ... Thermowell.pdf · with ASME PTC 19.3...

Close end tube (Pipe) type thermowell

Service intended

MaterialIn general, the thermowell material chosen for the installation is governed mainly by the corrosion condition the themowell will face. Recommended material for various services are given in the corrosion table.Occasionally the material consideration is one of strength rather than corrosion. For example, a stainless steel thermowell may be required for a high pressure water service where otherwise a brass thermowell would be satisfactory from a corrosion standpoint.

■

InsertionThe distance from the end of the well to the underside of the thread or other connection means (Designated as "U") is the insertion length.

* Note. Depending on the material and U-length, the appearance of the connector may change.

■ Bore sizeAlmost any installation uses several types of temperaturemeasuring instruments.The selection of a standard bore diameter can produceextreme flexibility within the plant.

■

Selection of thermowell

Structure

909

Model : A500, A510 seriesAD05-01

Standard features

Temperature sensors or indicating type temperature gauges are not directly inserted into the process pipe, unless these are used to measure the outside temperature of process pipe, instead, these are used with thermowells. By using thermowells, sensors and gauges will not interfere with the process line operation, and the users are able to perform the maintenance procedure of the process line more easily.A500 and A510 Series are either pipe or tube with one end is sealed. These thermowells are used in the process pipe where a very slow current is exist or in a container, and its length can be vary.

T U

TUBE

35 T U

TUBE

TUBE

T U

U

TUBE

25 T C

Spec. sheet no.

A5000

A5001

A5100

A5101

Tapered or straight typeTapered type thermowells provide greater stiffness for the same sensitivity. The higher strength to weight ratio gives these thermowells higher natural frequency than for equivalent length straight type thermowells, thus permitting operation at higher fluid velocity.

■

910

Main order Ordering information

A50001 2 3 4 5 6 7 8

AX AX 0 A A A(1) AZ9

010

011

1

Sample ordering code

Thread connection with extensionFlange connectionFlange connection with extension

Thread connection

1. Base modelA5000A5001A5100A5101

S25C304SS

316L SS304L SS

2. Material of well

310SS

446SS321SS

Hastelloy-CInconel 600

MonelTitanium

AXBXDXEXFXGXHXJXKXLXMX

316SS + PTFE lining304SS + PTFE lining

316L SS + PTFE coating304L SS + PTFE coating

Incoloy-800

A106SSA-S

A335P11GK-Sic

Others

PXQXRXSXTX1XWX3XYXZX

S.W.

PTNPT

150 Lb RFPF

8. Process connection type

150 Lb RFSF

300 Lb RF150 Lb FF

300 Lb FF300 Lb RFSF

600 Lb RF600 Lb RFSF10K RF

AZAAABPFACADAEAFAGAHAJAKKL

10K RFSF

PN10 RF10K FF

PN25 RFPN16 RF

PN40 RF

5K FF5K RF

20K RFSF20K RF

20K FFOther

KMKNDADBDIDOKAKTKPKQKRZZ

9. Insertion length ("U") length (mm)

012345678A

80100150200250300350400450500

BCDEFGHJKL

6007008009001,0001,5002,0002,5003,0003,500

10. "T" length (mm)

012

4550 below50 above

4,0005,0006,0007,0008,0009,00010,000Other

MNPQRSTZ

½" NPT

½" PF½" PT

4. Internal connection

012

¾" NPT

¾" PT¾" PF

345

½" (15A)

1" (25A)¾" (20A)

1½" (40A)1¼" (32A)

7. Process connection size

A(1)B(1)

CDE

2" (50A)

3" (80A)2½" (65A)

Other4" (100A)

FGHIZ

14

1716

21.719

5. Pipe (Tube) outer diameter (mm)

17.3

ABCDEF

151213.81012.713

GHIJKL

2521

30402021.3

NOPQRS

3.7

3.03.2

2.8

6. Pipe (Tube) thickness (mm)

Note. Available for flange connection only

ABCD

2.32.01.51.0

EFGH

0.7

5.02.5

JKL

Note : Please choose a code of next higher length if applicable length is not. Actual length shall be specified.

Note : Actual length shall be specified.

S25C

316SS304SS

316L SS304L SS

3. Material of flange

310SS321SS


Monel

TitaniumAXBXCXDXEXFXGXJXKXLX

316SS + PTFE lining304SS + PTFE lining


Incoloy-800A105A182F11Others

MXPXQXRXSXTXWXYXZX

Note. Please give XX to 8,9 character for A500 seriesth

11. Option

012

NonePlug and chain (304SS)Plug and chain (316SS)

Bar stock thermowell with thread connection

Service intended

MaterialIn general, the thermowell material chosen for the installation is governed mainly by the corrosion condition the themowell will face. Recommended material for various services are given in the corrosion table.Occasionally, the material consideration is one of strength rather than corrosion. For example, a stainless steel thermowell may be required for a high pressure water service where otherwise a brass thermowell would be satisfactory from a corrosion standpoint.

■


■ Bore sizeAlmost any installation uses several type of temperaturemeasuring instruments.The selection of a standard bore diameter can produceextreme flexibility within the plant.

■


Structure

911

Model : A600 seriesAD06-01

Standard features

Temperature sensors or indicating type temperature gauges are not directly inserted into the process pipe, unless these are used to measure the outside temperature of process pipe, instead, these are used with thermowells. By using thermowells, sensors and gauges will not interfere with the process line operation, and the users are able to perform the maintenance procedure of the process line more easily. A600 series are seamless round bar type thermowell, and does not contain any welded area by processing the internal area of the round bar. It is designed to be installed onto the process line by using screw created on the thermowell, and normally used in the process line where the pressure and the current exist.

T U

25 T C U

T U

25 T C U

T U

L

25 T C U

L

A6000 A6010 A6020

A6001 A6011 A6021

Spec. sheet no.

* Note. Depending on the material and U-length, the appearance of the connector may change.

912


A60001 2 3 4 5 6 7 8

AXXX 0 A0 A AA 0 19

1 Sample ordering code

1. Base modelA6000A6001A6010A6011A6020A6021

Straight bar stockStraight bar stock with extensionTapered bar stockTapered bar stock with extensionStepped bar stockStepped bar stock with extension

S25C

316SS304SS

316L SS304L SS

2. Material of well

310SS

446SS321SS

A182F304

AXBXCXDXEXFXGXHXIX

Inconel 600Hastelloy-CMonelTitaniumA182F316Incoloy-800A105A182F11Others

JXKXLXMXOXTXWXYXZX

6.Process connection type

AAABPF


01234567

80100150200250300350400

8ABCDEFZ

4505006007008009001,000Other

½" NPT

½" PF½" PT


012

¾" NPT

¾" PT¾" PF

345

4. Tip outer diameter / Bore size (mm)

A0A1B0B1B2C0C1

14 / 714 / 916 / 716 / 916 / 1017 / 717 / 9

NPTPTPF

½" ¾" 1"1¼"1½"

17 / 1017 / 1219 / 719 / 919 / 1019 / 1221 / 10

C2C3D0D1D2D3D4

5. Process connection size

ABCDE


8. "T" length (mm)

012

4550 below50 above


9. Option

012


Sanitary thermowell (3-A marking)

Service intended

Tri-clamp connection1S, 1½S and 2S

Process connection

½" (N)PT, femaleGauge connection

7, 9, 10 and 12 mmBore diameter

304SS, 316SS and 316L SSMaterial

Max. Ra 32 µin. (0.8 µm)Surface finish

913

Model : A603AD06-02

Standard features

A603 thermowell for temperature sensor andtemperature gauage are recommended for all processsystems where pressure, velocity, viscous, abrasive,and corrosive materials are present individually or incombination. A properly selected thermowell willprotect the temperature instrument from possibledamage resulting from these process variables.Furthermore, thermowell permits removal of thetemperature instrument for replacement, refair, ortesting without effecting the process media or thesystem.

Spec. sheet no.

914


A60301 2 3 4 5 6 7 8

EX 0 A0 C 4 1 19

1Sample ordering code

1. Base modelA6030 Sanitary thermowell (3-A marking)

2. MaterialEXCXBXDX

316LSS316SS304SS304L SS

3. Internal connection01

½" NPT½" PT

5. Process connection sizeCEF

1"1½"2"

6. Process connection type 4 Tri-clamp


A0A1B0B1B2C0C1

14 / 714 / 916 / 716 / 916 / 1017 / 717 / 9

17 / 1017 / 1219 / 719 / 919 / 1019 / 1221 / 10

C2C3D0D1D2D3D4


01234567

80100150200250300350400

8ABCDEFZ

4505006007008009001,000Other


8. "T" length (mm)

012

4550 below50 above


9. Option

012


915

A603 : Standard product drawing

916

Memo

Bar stock thermowell with flange connection

Service intended

MaterialIn general, the thermowell material chosen for the installation is governed mainly by the corrosion condition the themowell will face. Recommended material for various services are given in the corrosion table.Occasionally, the material consideration is one of strength rather than corrosion. For example, a stainless steel thermowell may be required for a high pressure water service where otherwise a brass thermowell would be satisfactory from a corrosion standpoint.

■



■


■ OptionWake frequency calculations in accordancewith ASME PTC 19.3WISE Inc. offers this as an engineering service.

■


StructureA6100

A6101

917

Model : A610, A611, A612, A623AD06-03

Standard features

Temperature sensors or indicating type temperature gaugesare not directly inserted into the process pipe, unless theseare used to measure the outside temperature of process pipe,instead, these are used with thermowells. By usingthermowells, sensors and gauges will not interfere with theprocess line operation, and the users are able to perform themaintenance procedure of the process line more easily.These types are most common bar type, and these areinstalled onto the process line by attaching a flange. It is usefulin the process line where a high pressure and a fast currentexist. A623 is manufactured with a Full Penetration weldingprocedure so it can be used in a high pressure gas line.

A6110

A6111

A6120

A6121

A6230

A6231

T U

35 T U

T U

35 T U

T U

L

35 T U

L

Spec. sheet no.

918


A61001 2 4 5 6 7 8 9

AX 0 A0 A(1) DB 1 13

BX10


1. Base modelA6100A6101

A6110A6111

A6120A6121

A6230A6231

Straight bar stock (Flanged connection)Straight bar stock (Flanged connection with extension)Tapered bar stock (Flanged connection)Tapered bar stock(Flanged connection with extension)Stepped bar stock (Flanged connection)Stepped bar stock(Flanged connection with extension)Tapered bar stock (F.P welding)Straight bar stock (F.P welding)

S25C

316SS304SS

316L SS304L SS

2. Material of well

310SS

446SS321SS


A182F304

Monel

TitaniumAXBXCXDXEXFXGXHXIXJXKXLX

Tantalum clad

316SS + PTFE lining304SS + PTFE liningA182F316


Incoloy-800

A105A182F91

A182F11A182F321Others

MXNXOXPXQXRXSXTXVXWXYX23ZX


012345

80100150200250300

350400450500600700

678ABC

DEFZ

8009001,000Other

10. Option

01256

NonePlug and chain (304SS)Plug and chain (316SS)Velocity colorVelocity color with plug and chain

½" NPT

½" PF½" PT


012


A0A1B0B1B2

14 / 714 / 916 / 716 / 916 / 10

C0C1C2C3D0

17 / 717 / 917 / 1017 / 1219 / 7

½" (15A) ¾" (20A)1" (25A)1¼" (32A)

PN10 RFPN16 RF150 Lb FF150 Lb RF150 Lb RFSF300 Lb FF300 Lb RF300 Lb RFSFPN25 RF600 Lb RF600 Lb RFSF600 Lb RTJ900 Lb RF

900 Lb RTJ1,500 Lb RF1,500 Lb RTJ2,500 Lb RF2,500 Lb RTJ10K FF10K RF10K RFSF20K FF20K RF20K RFSFPN40 RFOther

19 / 919 / 1019 / 1221 / 10

D1D2D3D4

6. Flange size

A(1)B(1)

CD

1½" (40A)2" (50A) 2½" (65A)

EFG

3" (80A)4" (100A)Other

HIZ



Note : Not available for flange N code is not available for A611, A612

S25C

316SS304SS

316L SS304L SS

310SS

446SS321SS


A182F304

Monel

TitaniumAXBXCXDXEXFXGXHXIXJXKXLX

Tantalum clad

316SS + PTFE lining304SS + PTFE liningA182F316


Incoloy-800

A105A182F91


MXNXOXPXQXRXSXTXVXWXYX23ZX

Note : Not available for flange N code is not available for A611, A612

3. Material of flange

7.Process connection type

DADBAEACADAHAFAGDIAJAKAVAS

AWATAXAUAYKNKLKMKRKPKQDOZZ

9. "T" length (mm)

012

4550 below50 above


Bar stock thermowell with welded connection

Service intended

MaterialIn general, the thermowell material chosen for the installation is governed mainly by the corrosion condition the thermowell will face. Recommended material for various services are given in the corrosion table.Occasionally, the material consideration is one of strength rather than corrosion. For example, a stainless steel thermowell may be required for a high pressure water service where otherwise a brass thermowell woule be satisfactory from a corrosion standpoint.

■

InsertionThe distance from the end of the well to the underside of the thread or other connection means (Designated as"U") is the insertion length.


■



■


Structure

919

Model : A630, A631, A632AD06-04

Standard features

Temperature sensors or indicating type temperature gauges are not directly inserted into the process pipe, unless these are used to measure the outside temperature of process pipe, instead, these are used with thermowells. By using thermowells, sensors and gauges will not interfere with the process line operation, and the users are able to perform the maintenance procedure of the process line more easily.These thermowells can be used in a high steam line or Vapor line. These are directly welded onto the socket or pipe so can be a semipermanent. Therefore, the user must carefully decide its material and specification before welding process is performed.

A6311

A6320

A6300

A6310

T U

T U

T U

T U

L

Spec. sheet no.

920


A63001 2 3 4 5 6 7

AX 0 A0 AAZ 2 18


1. Base modelA6300A6310A6311A6320

Straight bar stock (Socket welded type)Tapered bar stock (Socket welded type)Tapered bar stock (Weld in type)Stepped bar stock (Socket welded type)


01234567

80100150200250300350400

8ABCDEFZ

4505006007008009001,000Other

½" NPT

½" PF½" PT


012


A0A1B0B1B2C0C1

14 / 714 / 916 / 716 / 916 / 1017 / 717 / 9

½"¾"1" 1¼"1½"2"

17 / 1017 / 1219 / 719 / 919 / 1019 / 1221 / 10

C2C3D0D1D2D3D4

5. Socket size

AAZBAZCAZDAZEAZFAZ


S25C

316SS304SS

316L SS304L SS

2. Material of well

310SS

446SS321SS

A182F304

AXBXCXDXEXFXGXHXIX

Inconel 600Hastelloy-CMonelTitaniumA182F316Incoloy-800A105A182F11Others

JXKXLXMXOXTXWXYXZX

Note : Not available for A601 and A602

7. "T" length (mm)

012

4550 below50 above


8. Option

012


Vanstone type thermowell

Service intended

MaterialIn general, the thermowell material chosen for the installation is governed mainly by the corrosion condition the thermowell will face. Recommended material for various services are given in the corrosion table.Occasionally, the material consideration is one of strength rather than corrosion. For example, a stainless steel thermowell may be required for a high pressure water service where otherwise a brass thermowell woule be satisfactory from a corrosion standpoint.

■

InsertionThe distance from the end of the well to the underside of the thread or other connection means (Designated as"U") is the insertion length.


■



■

Standard "T" lengthWell size 1½" or DN40 : 40 mm 2" or DN50 : 45 mm

■


Structure

921


Standard features

Vanstone type thermowell is produced without any welding process by processing the whole round bar. Since it does not involve any welding process, it is used when high pressure, high velocity fluid and corrosive process media such as penetrating gas exist, and serving to isolate and protect from any leakage. The required flange is not standard and can be provided as an optional extra.

A6400 A6410 A6420

A6401 A6411 A6421

Spec. sheet no.

922


A64001 2 4 5 6 7 8 9

BX 0 A B C AC 13

BX10


1. Base modelA6400A6401A6410A6411A6420A6421

Straight bar stock Straight bar stock with flange Tapered bar stock Tapered bar stock with flangeStepped bar stock Stepped bar stock with flange

316SS304SS

316L SS304L SS

2. Material of well

310SS321SS

Hastelloy-CInconel 600A182F304

MonelTitanium

BXCXDXEXFXGXIXJXKX

A182F316Incoloy-800

A105A182F91


LXMXOXTXVXWXYX23ZX

316SS304SS

316L SS304L SS

3. Material of flanged

310SS321SS

Hastelloy-CInconel 600A182F304

Monel

TitaniumBXCXDXEXFXGXIXJXKXLX

A182F316Incoloy-800

A105A182F91

A182F321A182F11

OthersNot applicable

MXOXTXVXWXYX23ZXXX

10. Option

012


½" NPT

½" PF½" PT


012


ABCDEFGHIJ

14 / 714 / 916 / 716 / 916 / 1017 / 717 / 917 / 1017 / 1219 / 7

None6.5 (Standard)Other

150 Lb RF300 Lb RF600 Lb RF900 Lb RF2,500 Lb RF(Not available 1½" and DN)1,500 Lb RFPN10 RFPN16 RF

PN25 RFPN40 RF600 Lb RTJ900 Lb RTJ1,500 Lb RTJ2,500 Lb RTJ(Not available 1½" and DN)OtherNone

19 / 919 / 1019 / 1221 / 1014 / 816 / 817 / 819 / 821 / 8

KLMNOPQRS

6. Stepped bore size (mm)

ABC

1"1½"2"Other

7. Well size for flange

CEFZ


8. Flange class, sealing face

ACAFAJASAU

ATDADB

DIDOAVAWAXAY

ZZXX


012345

80100150200250300

350400450500600700

678ABC

DEFZ

8009001,000Other


923

Standard product drawing

924

Thermowell

Helical strake type thermowell

Service intended

Standard type thermowell A6500 type thermowell

A650 Series_01


Description

Thermowell is manufactured and calculated according to ASME PTC 19.3 TW-2016 to protect it from the loads of the flux. If the calculated value is not appropriate, then shorten the length of the Thermowell, and increase the root and the tip diameter of the Thermowell to change the outcome value, or try to change the structure by installing the support collar on the Thermowell. However, these changes have its own limits. A650 Series could reduce the amplitude of oscillation by 70 %, and reduce the danger of breakage of Thermowell by VIV (Vortex Induced Vibration). Furthermore, because it reduces the loads on the Thermowell, it makes the installation possible without installing the support collar and without the change of Nozzle.

The oscillation of vortices which is caused by VIV can be found around the Thermowell. If the vortex shedding frequency approaches to the natural frequency, then the resonance could cause the breakage of the Thermowell.

By comparing the standard Thermowell with A650 Series, the noticeable decrease of the vortices could be found around the A650 Series. Furthermore, it could reduce the chance of breakage of the Thermowell which is caused by VIV.

Velocity in Top View Velocity in Top View

Velocity in Side View

Spec. sheet no.

A650 Series_02


A65101 2 4 5 6 7 8 9

BX 0 E0 C DA 3 03

BX10


1. Base modelA6510A6520A6530

Flanged Type ThermowellVanstone Type ThermowellSocket Type Thermowell

316SS304SS

316L SS304L SS

2. Material of well

310SSOthers

BXCXDXEXFXZX

316SS304SS

316L SS304L SS

3. Material of flanged

310SSOthers

BXCXDXEXFXZX

9. "T" length (mm)

012

4550 below50 above

½" NPT

½" PF½" PT


012


E0 20 / 7

PN10 RFPN16 RF150 Lb FF150 Lb RF150 Lb RFSF300 Lb FF300 Lb RF300 Lb RFSFPN25 RF600 Lb RF600 Lb RFSF600 Lb RTJ900 Lb RF

900 Lb RTJ1,500 Lb RF1,500 Lb RTJ2,500 Lb RF2,500 Lb RTJ10K FF10K RF10K RFSF20K FF20K RF20K RFSFPN40 RFOther

20 / 9E1

6. Flange size

CDEF

1" (25A)1¼" (32A)1½" (40A)2" (50A)

2½" (65A)3" (80A)4" (100A)Other

GHIZ


10. Option

0128

NonePlug and chain (304SS)Plug and chain (316SS)F.P welding (Only flanged type)


7. Process connection type

DADBAEACADAHAFAGDIAJAKAVAS

AWATAXAUAYKNKLKMKRKPKQDOZZ


345678A

200250300350400450500

6007008009001,000Other

BCDEFZ


A650 Series_03

Standard product drawing

A650 Series_04

Memo

Date post:	18-Feb-2021
Category:	Documents
Upload:	others
View:	5 times
Download:	0 times

Close end tube (Pipe) type thermowell Model : A500, A510 ... Thermowell.pdf · with ASME PTC 19.3...

Documents