CO2 Laser Cutting System SPL3700E Seriesyenshin.com/SPL3730.pdf · CO2 Laser Cutting System...

Shibuya Kogyo Co.,LTD.

CO2 Laser Cutting System SPL3700E Series

(May 2007)


Shibuya Original Laser (Model:SOL20V)Economical

Medium Speed Spiral Flow Laser ResonatorMedium Speed Spiral Flow Laser Resonator

◆Medium speed gas flow results in1)More compact design than fast axial flow lasers2)Higher beam quality than slow axial flow lasers

◆ Medium speed gas flow reduces 1)Load on the blower (longer than other lasers) 2)Deposits on the electrodes3)Deposits on internal mirror

◆ Medium speed gas flow results in Dramatically longer life of mirror (8000H)



Multi-path type ResonatorMulti-path type Resonator

◆Very high quality beam◆Smaller consumption of electricity◆Long resonant length(as long as 14m)

The 5inch lens can cover a wider variety of materials andthicknesses.



Maximum Material Thickness Maximum Material Thickness

※These data figures may vary depending on material conditions etc.

0 2 4 6 8 10 12 14 16

Thickness (mm)

Aluminum

Stainless Steel(N2)

Stainless Steel(O2)

Milt

5" Lens

6.3" Lens

Mild Steel


Operator-friendly Laser Cutting MachineEconomical

Easy Access to MirrorsEasy Access to MirrorsJust

open covers



Easy access to Mirrors Easy access to Mirrors

◆Easy maintenance of mirrors1)Mirrors can be visually inspected and cleaned

without dismantling the mirrors or mirror holders2)Re-alignment of mirrors is not required

after inspection and cleaning◆Dust-free construction

1)Purge air blown on mirrors and higher air pressurein the mirror cabinet prevent the dirt on mirrors

Quick & Easy :Only 5 min.

With conventional mirrors

Over 30 min./mirror(Removal of mirror/ Inspection & Cleaning/

Re-mounting of mirror/Re-alignment of beam delivery)



Crash-Protection TorchCrash-Protection Torch

Crash

No damage

The cutting head swings to prevent damage.



Crash-Protection TorchCrash-Protection Torch

◆The highly responsive damage sensor and crashprotection torch prevents costly damage and down time.

◆Re-alignment of torch is not required after torchcrashes


Operator-friendly Laser Cutting Machine

High Performance Dust CollectionHigh Performance Dust Collection

PATPEND

Side View

Flow Direction

Exhaust FanAir Blower

The dust blown by fan is collectedby vacuum

Environmental Aware


Air blower + Exhaust = High Efficiency



High Performance Dust Collection High Performance Dust Collection

Air blower under the work table

Exhaust

Air BlowerFlow DirectionEasy-to-clean + Efficient

Environmental Aware



High Performance Dust CollectionHigh Performance Dust Collection

◆High efficiency dust and fumecollection using “Push & Pull” method ※dust collector is option

SPL3700

Exhaust

Air Blower

Air BlowerExhaustExhaust

Environmental Aware



Table GuardTable Guard

◆Table guard protects operatorfrom moving work table

Safe

Environmental Aware


High Productivity Laser Cutting MachineEfficient

High Speed PiercingHigh Speed Piercing

◆Shortens piercing time of Mild Steelof 9mm thickness and over

◆Raises productivity

0 5 10 15 20 25sec

ＳＳ12ｍｍ

ＳＳ16ｍｍ

高速ピアス従来ピアス

Comparison of piercing time Mild Steel 12mm 66％ reductionMild Steel 16mm 77％ reduction

◆High speed piercing ◆Conventional piercing

16mm

12mm


High Productivity Laser Cutting MachineEfficient

Fast Cutting Speed by CWFast Cutting Speed by CW

◆Enables continuous wave (CW) cutting of contoursand sharp corners at much faster speeds

◆Reduces consumption of assist gas ※Applicable to Mild Steel of 6mm thickness and under

For example : 4.5mm Mild Steel

Conventional Cutting137sec

(sharp corner 200mm/min) (other position2000mm/min)

Shibuya Cutting33sec

(all process 2500mm/min)

75% reduction


Operator-friendly Laser Cutting MachineEfficient

Compact FootprintCompact Footprint

◆All maintenance points are accessible from the operator’sside of the machine, allowinginstallation near walls

wall


High performance CNC (Model:YS840Di)Efficient

FeaturesFeatures

◆Newest Windows based on CNC ◆2G Byte memory ◆High speed arithmetic processing (64bit)◆UPS (uninterruptible power supply system)◆LAN connector◆Enable NC check and correction on display

*18iM(FANUC) is available



Cutting featuresCutting features

◆Excellent performance to follow the cutting program

Conventional YS840Di

Twice as sharp




Cutting featuresCutting features

◆Edge quality

Conventional YS840Di

Twice as clean

10μ

m




Standard equipment Standard equipment

◆Chiller (air dryer included)

◆Semi Auto oiling device

◆High pressure piping 150psi(Max. 0.99Mpa)

◆Rotary work-lifter (Japanese Patent)

◆CG (capacitive gap) sensor

◆Air purge for external beam path

Ｃｈｉｌｌｅｒ



Options Options

◆Auto focus

◆Touch sensor

◆Ultra high pressure assist gas piping 300psi(Max. 2.0Mpa)

◆2-pallet shuttle

◆10-bin stocker

◆Dust collector

◆Exhaust fan

◆Deionizer

◆CAD/CAM system “CAS6000”

◆compressor

◆Rotary table



Specifications Specifications

※1 Includes standard accessories such as laser resonator, chiller, etc.※2 Includes laser resonator. Chiller not included.

Model SPL3725E SPL3730EProcessing area 1550×2500mm 1550×3080mmMax. loading weight 375kg 585kgCutting speed 0～30m/min 0～30m/minRapid traverse speed (X,Y) 30m/min/Axis 30m/min/AxisRapid traverse speed (Z) 20m/min 20m/minPositioning accuracy 0.01/500mm 0.01/500mmZ-axis travel range 250mm 250mmControlled axes 3(X,Y,Z) 3(X,Y,Z)Simultaneous controllable axes 2(X,Y) 2(X,Y)Axes drive AC servo motors AC servo motorsMinimal unit of NC input 0.001mm 0.001mmLaser resonator model SOL20V (2000W) SOL20V (2000W)Input power requirement ※1 3φ 200V 50/60Hz 54.7kVA 3φ 200V 50/60Hz 59.7kVADimensions ※2 3170(L)×6120(W)×2425(H)mm 3170(L)×6775(W)×2425(H)mmMachine weight ※1 8000kg 9000kg

Date post:	22-Mar-2021
Category:	Documents
Upload:	others
View:	3 times
Download:	0 times

CO2 Laser Cutting System SPL3700E Seriesyenshin.com/SPL3730.pdf · CO2 Laser Cutting System...

Documents