Shibuya Kogyo Co.,LTD.
CO2 Laser Cutting System WTS4112 “FALCON-S
(May 2010)
Shibuya Kogyo Co.,LTD.
Outline of Laser Cutting MachineEconomical
Full Closed Cover TypeFull Closed Cover TypeCutting Head
Laser Resonator ( built-in )
Work Table
NC Control Unit ( built-in )
Remaining Material Pan
Operation Panel
Shibuya Kogyo Co.,LTD.
Operator-friendly Laser Cutting MachineEfficient
Compact FootprintCompact Footprint
◆Advantages 1. Able to reduce investment in ground and building
at building new factories for laser cutting system.
2. Allows more space to be used by replacingexisting bigger machine.
3. Space for peripheral equipment such as chiller,compressor and dust collector can be secured easily.
This machine doesn’t take up a much space.
Only 5.71m2 !Only 5.71m2 !
Shibuya Kogyo Co.,LTD.
Operator-friendly Laser Cutting MachineEfficient
Advantages of “ BEAM FLYING “ MethodAdvantages of “ BEAM FLYING “ Method
◆Advantages1. HIGH SPEED and ACCURACY for light
weight drive section.
2. Workpieces DON’T shift because of the fixed work table.
3. The work table is fixed so that machinesize is very COMPACT.
Operator-friendly Laser Cutting Machine
High Performance Dust CollectionHigh Performance Dust Collection
Environmental Aware
◆Fume Dust Free Structure for Clean Work Environment
Shibuya Kogyo Co.,LTD.
■ Work Table Exhaust System
Exhaust Duct
Shibuya Kogyo Co.,LTD.
Shibuya Original Laser (Model:SOL13H)Economical
Medium Speed Spiral Flow Laser ResonatorMedium Speed Spiral Flow Laser Resonator
◆Medium speed gas flow results in1)More compact design than fast axial flow lasers2)Higher beam quality than slow axial flow lasers
◆ Medium speed gas flow reduces 1)Load on the blower (longer than other lasers) 2)Deposits on the electrodes3)Deposits on internal mirror
◆ Medium speed gas flow results in Dramatically longer life of mirror (8000Hrs.)
Shibuya Kogyo Co.,LTD.
Shibuya Original Laser (Model:SOL13H)Economical
Multi-Path Type ResonatorMulti-Path Type Resonator
◆Very High Quality Beam◆Smaller Consumption of Electricity◆Long Resonant Length (as long as 14m)
The 5inch lens can be used with a wider variety of materials and thicknesses.
Shibuya Kogyo Co.,LTD.
Shibuya Original Laser (Model:SOL13H)Economical
Maximum Material ThicknessMaximum Material Thickness
※These data figures may vary depending on material conditions etc.
0 5 10 15 20
Thickness (mm)
Arclylic(Air)
Aluminum(Air)
Stainless Steel(N2)
Mild Steel(O2)
Shibuya Kogyo Co.,LTD.
Operator-friendly Laser Cutting MachineEconomical
Crash-Protection TorchCrash-Protection Torch
Crash
No Damage
The cutting head swings to prevent damage.
Shibuya Kogyo Co.,LTD.
Operator-friendly Laser Cutting MachineEconomical
Crash-Protection TorchCrash-Protection Torch
◆The highly responsive damage sensor and crashprotection torch prevents costly damage and down time.
◆Re-alignment of torch is not required after torchcrashes
Shibuya Kogyo Co.,LTD.
Operator-friendly Laser Cutting MachineEconomical
Workpiece Positioning Mechanism ( Clamping and Locating )Workpiece Positioning Mechanism ( Clamping and Locating )
◆Origin position can be set easily by the positioning pin ( X-axis ) and the clamp.
◆Air clamp is the standard equipment.
Shibuya Kogyo Co.,LTD.
Operator-friendly Laser Cutting MachineEconomical
Even large workpieces can be loaded and positioned without trouble.Even large workpieces can be loaded and positioned without trouble.
◆ The transfer ball device on the work lifterenables a single operator to load large workpieces.
◆The work lifter turns over during cuttingoperation so that fumes and dust don’t get in the gap between the free bearings.
◆ The bearings rotate to the reference side so that workpieces are not shifted.
◆ Easy operation by foot pedal.
Shibuya Kogyo Co.,LTD.
Operator-friendly Laser Cutting MachineEconomical
Support PlateSupport Plate
◆ Quick release for its insertion mechanism
◆ Cutting program is registered in NC so thatcustomers can manufacture the support platethemselves.
◆ “Micro-Jointless-Cutting “ can be madefor cutting products over the pitch ofsupport plate.
Shibuya Kogyo Co.,LTD.
Operator-friendly Laser Cutting MachineEconomical
Remaining Waste TrayRemaining Waste Tray
◆ Remaining material can be taken out easilyby two remaining waste trays on the side of the work table.
◆ Remaining materials are not spattered sothat the work environment is clean.
Shibuya Kogyo Co.,LTD.
High performance CNC (Model:21i-MB)Efficient
FeaturesFeatures
◆ The operation panel can be stored, which makes effective use of work space.
◆ Full of Shibuya’s own technical know-how( Up to 8 kinds of materials, 12 different thickness
and 10 different parameters for microfabrication to high-speed cutting )
◆ The followings are the standard functions.- Maintenance cycle monitoring for consumable parts
such as filter, oil..etc.- Self trouble diagnosis program - Troubleshooting display
◆ External operation box is equipped as standard equipment.◆ 10.4 inch color LCD display ( with softkey ) ◆ USB memory for program installation
Shibuya Kogyo Co.,LTD.
CO2 Laser Cutting System WTS4112/SOL13H
Standard EquipmentStandard Equipment
◆Chiller (air dryer included)
◆Rotary Work-Lifter (Japanese Patent)
◆CG (capacitive gap) Sensor
◆Air Purge for External Beam Path
Chiller
Shibuya Kogyo Co.,LTD.
CO2 Laser Cutting System WTS4112/SOL13H
OptionsOptions
◆Auto Focus
◆Touch Sensor
◆Deionizer
◆Compressor
◆LAN Connection
◆Dust Collector
◆Exhaust Fan
◆CAD/CAM Software “CAS6000”
◆Rotary Table
Shibuya Kogyo Co.,LTD.
Specifications : WTS4112/SOL13H
※1 Includes standard accessories such as laser resonator, chiller, etc.※2 Includes laser resonator. Chiller not included.
5000kgMachine weight ※1
2450(L)×2330(W)×1670(H)mmDimensions ※2
3ph 200V 50/60Hz 47.2kVAInput power requirement ※1
SOL13H (1300W)Laser resonator model
0.001mmMinimal unit of NC input
AC servo motorsAxes drive
2(X,Y)Simultaneous controllable axes
3(X,Y,Z)Controlled axes
90mmZ-axis travel range
8m/minRapid traverse speed (Z)
30m/min/AxisRapid traverse speed (X,Y)
0~12m/minCutting speed
140kgMax. loading weight
1250×1250mmProcessing area
WTS4112/SOL13HModel