DIAGNOSTICA E MESSA A PUNTO
TOOLS FOR CAR REPAIR
Diagnostics and tuning 318
Injection 322
Timing 324
Ignition and carburation 330
Cylinder head and pistons 332
Maintenance 336
Lubrication and filtration 339
Electrical and battery 342
Wheels, steering and hubs 344
Brakes 347
Suspension and transmission 349
Bodywork 351
Storage units and tool assortments 12
317
1
CAP_15_GB_p316-325 4-10-2005 15:59 Pagina 317
318
TOOLS FOR CAR REPAIR DIAGNOSTICS AND TUNING
075 FDigital multimeter for automotive– Measurement direct voltage (DC): 200mV÷600V
and alternating voltage (AC): 200mV÷600V– Measurement direct current (DC): 2A÷10A and
alternating current (AC): 2A÷10A– Measurement, with clip-on ammeter 075 P: direct
current (DC)200A÷1000A and alternating current(AC): 200A÷1000A
– Measurement resistance: 200¸÷20M¸
– Measurement temperature with K-probe:-20°C÷1000°C (0°F÷1800°F)
– Measurement DWELL-angle: 0-90 (4 cyl.),0-60 (6 cyl.), 0-45 (8 cyl.)
– Measurement RPM (4-6-8 cylinders)– Continuity and diode testing– Display: 3 1/2 LCD (16 mm) 1999 dots with
automatic indication of functions and symbols– Automatic and manual output selection– Automatic low-battery indication– Automatic polarity indication– Automatic power-off with short beep after 15
minutes of non-use– Designed to comply with safety regulations
IEC1010-1, CAT III 600V and EU-regulations89/336/EEC and 73/23/EEC
– Insulation class: 600V CAT. III pollution degree 2– Operating temperature: 0÷40°C / 32÷104°F
<80% RH– Storage temperature: -10÷+50°C / 10÷122°F
<80% RH– Max voltage to ground: 600V DC/AC– Response in frequency: 40 - 400 Hz– Electronic protection for all outputs– Ramp time: 0,4 sec– Power supply: 3 1,5V batteries type AAA– Supplied with protection holster, pair of insulated
tips, K-type temperature probe, batteries andinstruction manual
– 12 months guarantee
a 158x74x32 mm
� 250 gr
075 PClip-on ammeter for digital multimeters– Measurement direct current DC (1A÷1000A) and
alternating current AC (1A÷1000A)– Maximum jaw opening: 55 mm.– Manufactured in compliance with safety regulations
IEC 1010 and IEC1010-2-032 and Europeancommunity regulations 89/336/EEC and 73/23/EEC
– Insulation class: 1000V CAT.II for IEC1010-1 – Operating temperature: from 0 to 40°C <80% RH– Storage temperature: from -10 to +50°C <80% RH – Max voltage to ground: 1000V with insulated cables– Response in frequency: 50 - 60 Hz – Overload protection up to 1200A for 60 sec.– Power supply: 9V battery type 6F22– Supplied in plastic case with instruction manual– 12 months guarantee
a 256x104x47 mm
� 520 gr
DIAGNOSTICS AND TUNING
CAP_15_GB_p316-325 6-10-2005 9:53 Pagina 318
319
TOOLS FOR CAR REPAIRDIAGNOSTICS AND TUNING
907 NDigital timing light
907 STiming light– For the stroboscopic visualization of the spark lead
marks– Suitable for 2 or 4 stroke engines until 2
sparks/rpm.– Cables and shock resistant top in rubber– Supplied in plastic box with cables and crocodile
clips– 12 months guarantee
a 310x285x110 mm
� 1,4 Kg
1650Infrared thermometer– For measuring the themperature of different vehicle
components: air conditioning, brake disks, tyres,engine
– Laser pointer– Display: 3 1/2 LCD 1999 dot, backlit, with automatic
reading of functions and sign– Measuring range: from -50°C to +538°C, from -58°F
to +1000°F– Automatic resolution: 0,1° C/F - 1°C/F– Calculation time: 2,5 times/sec– Out of range indication– Automatic reading of polarity with “-” symbol for
negative values– Emissivity: 0,95 fix– Optical report: D (distance)/ S (surface) = 8:1 mm.
ca.– Minimum measuring distance: 200 mm.– Laser diod: output < 1mW - wavelenght
630-670 nm class 2 (III)– Power supply: 9V battery (type 6LR61)– Supplied in nylon bag– 12 months guarantee
a 82x41,5x160 mm
� 180 gr
– For the stroboscopic visualization of the spark leadmarks
– Suitable for 2 or 4 stroke engines until 2sparks/rpm.
– Cables and shock resistant top in rubber– Checks:
Revolutions 400÷19999 rpmTiming advance: 0÷78°/90° (400/465 rpm)DWELL 0÷65 ms
0÷100%0÷120° (> 600 rpm)
Direct current: 1÷70 VPeak voltage: 1÷70 VTiming revolutions counter: 60÷6000 rpmReading memoryPower supply: 9,5÷15 V
– Supplied in plastic box with cables and crocodileclips
– 12 months guarantee
a 310x285x110 mm
� 1,7 Kg
CAP_15_GB_p316-325 4-10-2005 15:59 Pagina 319
320
TOOLS FOR CAR REPAIR DIAGNOSTICS AND TUNING
1710Fuel pressure tester– Tests multi-point fuel injectiors– Range: 0÷10 bar– Measures:
Petrol pump pressureSystem pressureResidual pressure
– For checking pressure regulator– Supplied with 26 adapters and couplers in plastic
case– 12 months guarantee
a 480x340x130 mm � 4,6 Kg
1710 MSingle-point fuel injection pressure gauge– For a more accurate control of single-point
injectors– Range: 0÷2 bar– Supplied with adaptor � 480 gr
1 long spark plug adaptor M14 375
3 spark plug adaptor M14 72
4 spark plug adaptor M18 58
5 spark plug adaptor M10 47
6 spark plug adaptor M12 50
n° description �gr
1410 BSpark plug adapters
1
3
5
4
6
1410 B2Spare rubber retainers
1410Compression tester for petrol engines– Test cards for 1 up to 10 cylinders– Working range from 4 to 17 bar– Integrated starter-motor control– Supplied in plastic case– 12 months guarantee
a 440x375x100 mm � 2,2 Kg
1 compression tester -
1 pack of 50 test cards 1410 B10
1 adaptor for spark plugs 1410 B6
1 pack of 5 spare rubber retainers 1410 B2
pcs description art./size
1410 B10Test cards
FUEL PRESSURE TESTER 1710
With the diffusion in Europe of catalytic converters, a large percentage of petrol engines features single ormultiple fuel injection system.For these vehicles fuel pressure checks are very important.
Measurements:– pump pressure– system pressure– pressure regulator performance– residual pressure
Diagnostics:– faulty pump– faulty pressure regulator– clogged fuel pipe or filter– leaky injector– faulty pump's non-return valve
CAP_15_GB_p316-325 4-10-2005 16:00 Pagina 320
321
TOOLS FOR CAR REPAIRDIAGNOSTICS AND TUNING
1450Compression tester for Diesel engines– Test cards for 1 up to 10 cylinders– Working range from 8 up to 40 Bar– Integrated starter-motor control– Supplied in plastic case– 12 months guarantee
a 440x380x100 mm � 2,3 Kg
1 compression tester –
1 pack of 50 test cards 1410 D10
3 adaptors for dummy injector –
pcs description art./size
62x16 65
dimensions �mm gr
1450 DC1Dummy heater plug
100x31 330
dimensions �mm gr
1450 DI1Dummy injector
105x21 215
dimensions �mm gr
1450 DI2Dummy injector
1450 DI3Dummy injector
134x19 227
dimensions �mm gr
1450 D10Test cards
Alfa Romeo x x x x
Aro x x
Audi x
Autoland x
BMW x
Bonetti x x x
Bremach x
Chrysler x
Ciemme x x
CIT x x
Citro‘n x x x x
Daihatsu x
Delta x x
Ebro x
Fiat x x x x
Fissore x x
Ford x x
Innocenti x
Jeep x x x
Lada x
Lancia x x x x
Land Rover x x
Laverda x x
Lincoln x
Mazda x
Mercedes x x
Mercury x
Mitsubishi x
Nissan x
Opel x
Peugeot x x
Portaro x x x
Puch x x
Renault x x x
Rover x x x
Seat x x x
Talbot x x
Toyota x x
UAZ x x x
UMM x x
Vauxhall x x
Volga x
Volkswagen x x
Volvo x x
makes 1450 DI1 1450 DI2 1450 DI3 1450 DC1
CAP_15_GB_p316-325 4-10-2005 16:00 Pagina 321
asta �mm gr
899Stethoscope– To locate engine defects– Plastic grip
322
TOOLS FOR CAR REPAIR INJECTION
1785Vacuum/pressure pump– Checks:
Vacuum advance in conjunction with a timing light Seal of fuel supply systems Seal of brake power assistance and any otherVacuum-controlled systemTurbo wastengate control valves
– Vacuum/pressure selection valve– Vacuum: 0÷-1 bar – Pressure: 0÷1,5 bar– Supplied with 0,8 m flexible hose and 6 inserts
� 465 gr
230 188
8 110 100
10 110 96
Ø L �mm mm gr
869Fuel-line pliers– To disconnect fuel-line fittings
906 NLTest liquid– For use with pump 906 N– Conformable to ISO 4143– Contains 2 L
0÷400 220x100x410 3,8
0÷600 220x175x440 3,8
bardimensions �
mm Kg
906 NPump for checking and calibrating dieselengine injectors– To check the correct working of injectors and
atomization pressure– Tank with filter– Supplied with connectors
INJECTION
215 85
L �mm gr
906 NAConnection pipe– For Bosch injectors– M12 x 150
215 88
L �mm gr
906 NBConnection pipe– For Bosch injectors– M14 x 150
CAP_15_GB_p316-325 4-10-2005 16:00 Pagina 322
323
TOOLS FOR CAR REPAIRINJECTION
22 1/2 29 98 165
W Y Ø L �mm ” mm mm gr
887/22LSocket for diesel engine injectors– Long socket with bihexagonal opening
27 1/2 36 87 265
W Y Ø L �mm ” mm mm gr
887/27Socket for diesel engine injectors– Long socket with bihexagonal opening– All makes
21 1/2 29 83 157
W Y Ø L �mm ” mm mm gr
887/21Socket for diesel engine injectors– Long socket with bihexagonal opening
14 3/8 27 95 76
17 3/8 27 95 72
W Y Ø L �mm ” mm mm gr
884 BDiesel injection-linewrenches– Bihexagonal opening
886Extractor for Common Rail electronicinjectors– For extracting all Bosch electronic injectors without
damaging them– Particularly suited to all FIAT group cars
� 1,3 Kg
EXTRACTORFOR ELECTRONIC INJECTORS 886The various maintenance operations on modern engines, thatare more and more compact, require the use of specific tools,capable of fully exploiting the limited access spaceavailable toreach the various components.Therefore, it is necessary to have a tool suitable todisassemble the common-rail electronic injectors even inspecial or difficult situations (for instance whether stuck orjammed) without damage.
CAP_15_GB_p316-325 4-10-2005 16:00 Pagina 323
324
TOOLS FOR CAR REPAIR TIMING
800 40 140 600
L Belt Ø min. Ø max. �mm mm mm gr
435 AV-pulley stay– For holding alternator or water-pump V-pulleys– Also useful for large-diameter oil filters
TIMING
800 40 140 570
L Belt Ø min. Ø max. �mm mm mm gr
435 BMulti-groove pulley lock– To hold multi-groove pulleys in position while
tightening or removing them– Makes it possible to rotate the pulley to position it
correctly
560 40 140 600
L Belt Ø min. Ø max. �mm mm mm gr
435 CTiming pulley stay– To hold notched pulleys while removing or
tightening them– Rotates the pulley to correct position when timing
camshaft or engine
435 DNTiming pulley turner– To rotate timing pulley and reach the T.D.C.– Suitable for all engines: petrol and DIESEL– Dimensions: 440x65x50 mm
� 0,9 Kg
435 FNExtractor for timing pulleys– To remove timing pulleys without damage– Adjustable arms, suitable for different diameters– Capacity: 90 x 110 mm.
� 0,9 Kg
435 TBNMulti-groove pulley extractor– To disassemble and assemble multi-groove pulleys
of the crankshaft (grip on pulley grooves)– Adjustable claws from ø 45 to 175 mm., to suit to
different pulleys– Groove pitch: 3,56 mm.
� 0,9 Kg
CAP_15_GB_p316-325 4-10-2005 16:00 Pagina 324
325
TOOLS FOR CAR REPAIRTIMING
435 ZSet of pins for automatic tighteners– To keep automatic tighteners’ compression during
operations on belts– Ø pins: 0,80÷1,90 mm.
� 30 gr
435 VUniversal pulley block– For petrol and diesel
engines– To hold timing pulleys of
engines with single ordouble camshaft and fordiesel injection pumps
– Supplied in plastic case
a 270x185x90 mm
� 1,2 Kg
436Universal belt-tension gauge– To perform tension checks after fitting of any belt
model, regardless of the manufacturer– To check timing, alternator and air-conditioning
belts– The result is registered by a sensor which
measures the belt vibration frequency (caused bythe touch of a finger), and appears on the gaugedisplay
– Unit of measurement: Hz– Supplied with the complete guide of reference
values, to be compared with the obtainedmeasurements
– The values are classified according to the producer,model and engine
– Supplied in plastic case
a 320x270x60 mm
� 900 gr
Checks on timing belt
Checks on the timing belt,be it on new or usedvehicles, is a fundamentaloperation to assure beltendurance and engine life.With this instrumentrepairers can make preciseand quick measurementsregularly and, at the sametime, be sure that theoperation has been made ina correct and efficient way.
CAP_15_GB_p316-325 4-10-2005 16:00 Pagina 325
326
TOOLS FOR CAR REPAIR TIMING
1308Timing tools set for RENAULT/OPEL– Engines: 2.2 DCI, 2.2 DTI, 2.2 16V, 2.5 DCI – RENAULT: Laguna II, Espace and Grand Espace,
Master, Traffic– OPEL: Vivaro, Movano, Astra B, Vectra B, Signum,
Zafira– Supplied in sheet steel case
a 283x192x51 mm � 2,7 Kg
1309Timing tools set for BMW– Petrol and diesel engines: 316, 318, 320, 323, 328,
518, 520, 530, 535, 728, 735, 750, 840, M3, X5, Z3– Supplied in sheet steel case
a 418x380x51 mm � 7,8 Kg
1310Timing tools set for HYUNDAY, MAZDA,MITSUBISHI– HYUNDAY: Sonata– MAZDA: 626, 323, Premacy– MITSUBISHI: Carisma, Space Star, Space Wagon,
Galant, Sigma, Pajero– Supplied in plastic case
a 320x275x60 mm � 1,5 Kg
1311/1Timing tools set for FORD– Engines 1.4, 2.0 TDCI, 2.0 TD, 2.4D– Fiesta, Fusion, Transit
a 200x138x51 mm � 0,3 Kg
Engine timing, after normal replacement of timing belt, is more ad morefrequently made outside the car dealers network.USAG has developed a specific range of different kits to satisfy therequirements connected to the more popular car brands.With every kit there is, in addition to the detailed instructions for use, acomplete list of the applications of each piece classified by type of engineand vehicle.
TIMING KITS
CAP_15_GB_p326-337 4-10-2005 16:04 Pagina 326
327
TOOLS FOR CAR REPAIRTIMING
1311Timing tools set for FORD– Petrol and diesel engines:
Fiesta, Escort, Orion, Focus, Mondeo, Cougar,Sierra, P100, Transit, Puma, Courier, Galaxy
– Supplied in sheet steel case
a 283x192x51 mm � 2,4 Kg
1312Timing tools set for OPEL– Petrol and diesel engines:
Corsa, Agila, Nova, Astra, Kadett, Tigra, Vectra,Zafira, Cavalier, Calibra, Frontera, Omega
– Supplied in sheet steel case
a 418x380x51 mm � 6 Kg
1313Timing tools set for PEUGEOT - CITROEN– Petrol and diesel engines:
106, 205, 307, 309, 405, 306, 605, 607, 806, Boxer,206, 406, Expert, Ulysse (Fiat)
– Citroen: AX, ZX, BX, Xsara, Saxo, Berlingo, Visa,Evasion, Xantia, XM, C5, Picasso, Jumper
– Supplied in sheet steel case
a 418x320x51 mm � 6,6 Kg
1314Timing tools set for RENAULT– Petrol and diesel engines:
Twingo, Clio, Kangoo, R19, R21, Trafic, Express,Megane, Scenic, Laguna, Espace, R25, Safrane,Master
– Supplied in sheet steel case
a 418x380x51 mm � 6,1 Kg
CAP_15_GB_p326-337 4-10-2005 16:05 Pagina 327
328
TOOLS FOR CAR REPAIR TIMING
1315Timing tools set for AUDI - SEAT -SKODA - VW– Petrol and diesel engines:
AUDI: 80, 100, A2, A3, A4, A6, A8, TTSEAT: Arosa, Ibiza, Cordoba, Inca, Toledo, Leon,Alhambra, TerraSKODA: Felicia, Octavia, FabiaVW: Corrado, Scirocco, Transporter, Lupo, Polo,Golf, Vento, Bora, Caddy, Passat, Sharon, NewBeetle, Santana, Galaxy (Ford)
– Supplied in sheet steel case
a 418x192x51 mm � 3,6 Kg
1316Timing tools set for DIESEL pumps– Bosch VE, Lucas, DPC/CAV, Rotodiesel– Supplied in sheet steel case
a 283x192x51 mm � 1,7 Kg
1318Timing assortment for FIAT– Engines: Fiat Multipla and Stilo 1600 16V – Supplied in plastic box
a 320x112x44 mm � 1,6 Kg
1319Timing tools set for FIAT - LANCIA– Engines: Fiat Punto and Lancia Y 1.2 16V – Supplied in plastic case
a 320x112x44 mm � 1,2 Kg
1344Timing tools set for FIAT Multijet– 1.3 Multijet engines installed on FIAT group cars– Supplied in plastic case
a 320x275x60 mm � 2 Kg
CAP_15_GB_p326-337 4-10-2005 16:05 Pagina 328
329
TOOLS FOR CAR REPAIRTIMING
1340/S2Tools for timing cam shafts– FIAT Bravo and Brava 1.6 16V
� 750 gr
134 382
L �mm gr
1342Tools for T.C.D. positioning on the 1stcylinder– FIAT– Engines: 1697 D - 1929 D - 1910 D/TD/JTD - 2387 JTD
277 21 405
L ø �mm mm gr
1343Tool for T.D.C. control– For establishing the T.D.C. of the first cylinder– For positioning the sensor support plate (static
electronic ignition)– To be used with a comparator
1343 TCBelt tensioner adapter– For tightening the notched timing belt
� 0,5 Kg
23 Adapters 1320 A÷M
1 Belt tensioner adapter 1343 TC
1 Tool for TDC control 1343
2 Tools for timing cam shafts 1340/S2
pcs description art./size
1320Timing tools set for FIAT - ALFA ROMEO -LANCIA– Supplied in plastic case
a 383x305x81 mm � 5 Kg
A y Fiat Bravo/Brava - Lancia Y10 1,4 12 V 1
B y Lancia K5 cil. 2,0 20 V engine VIS 2
≥ ‘96
C y Alfa 3,0 V6 24 V 4
Lancia 3,0 V6 24 V
D y Lancia (VIS 4 cil.) 2
E y Lancia 5 cil. ≤ 96 2
F y Fiat Bravo/Brava/Marea- 2
Lancia 1800 16 V 115 CV
Delta/Dedra 1800 16 V - 1860 847/C/2
G y Fiat Coupè/Barchetta - Lancia - 2
Alfa 1800 16 V 130 CV
H y Fiat Bravo/Brava/Marea 2,0 20 V 2
I y Alfa 145 - 146 - 147 - 2
156 1600 16 V Step “A”
L y Alfa 145 - 146 - 155 1400/1600 16 V 2
1400 16 V Step “A”
M y Alfa 156 1800 - 2000 16 V 2
N y Alfa 147 105 CV 1600 16 V 2
Type Colour Vehicle pcs.
1320Adapters
CAP_15_GB_p326-337 4-10-2005 16:05 Pagina 329
8 14,5 161 110
10 14,5 161 110
12 17 155 125
12L 17 178 150
W ø L �mm mm mm gr
278 DGlowplug wrenches with jointedsocket– � system for retaining the glowplug– Hexagonal opening– 3/8” square drive
279 DNGlowplug sockets– � system for retaining the glowplug– Hexagonal opening– 3/8” square drive and 17 mm hexagonal
drive
10 14,5 70 70
12 17,5 70 80
W ø L �mm mm mm gr
330
TOOLS FOR CAR REPAIR IGNITION AND CARBURATION
IGNITION AND CARBURATION
1620Glowplug tester– Allows easy and fast testing of glowplugs of diesel
engines and evaluating the causes of cold-startingmalfunctions
– LED sensor for diagnostics– Indicates the condition of the glowplug: short-
circuit, interruptions, insufficien power, highconsumption
– All makes– Power supply: 12 V
� 160 gr
14 19 90 85
14L 19 250 225
16 21,5 90 132
16L 21,5 250 310
18 25 90 182
19 25 90 166
20,8 27,5 90 200
W ø L �mm mm mm gr
279 3/8”Spark plug sockets– Hexagonal opening– Rubber gasket for retaining the spark
plug– 3/8” square drive
ISO 11168
16 22 90 132
16L 21,5 250 353
18 25 90 172
20,8 28 90 205
W ø L �mm mm mm gr
279 NSpark plug sockets– Hexagonal opening– Rubber gasket for retaining the spark
plug– 1/2” square drive
ISO 11168
16 22 84 17 120
18 25 84 19 155
20,8 27,5 84 22 187
W ø L a �mm mm mm mm gr
279 3/8” MGMagnetic sockets for spark plugs– Hexagonal opening– Magnetic system for retaining the spark
plug– 3/8” square drive
ISO 11168
279 3/8” MG/S3Set of three spark plug sockets(279 3/8” MG 16-18-20,8) � 440 gr
CAP_15_GB_p326-337 4-10-2005 16:05 Pagina 330
331
TOOLS FOR CAR REPAIRIGNITION AND CARBURATION
16L 21 140 235
18L 25 140 240
19L 25 140 250
20,8 25 85 180
20,8L 25 140 280
W a L �mm ø mm mm gr
277 NSocket wrenches for spark plugs– Removable sliding bar
with holes for a 90°working angle
– Device for storing thehandle inside the wrench
ISO 11168
16 22 270 290
18 25 270 329
19 25 270 325
20,8 26 270 331
W a L �mm ø mm mm gr
278 NT-handle spark plug wrencheswith jointed socket– Hexagonal opening– Rubber gasket for retaining
the spark plug– Removable sliding bar
ISO 11168
278 ASpare gasket– For 278 C - 278 N -
279 3/8 - 279 N
14-16
18
19
20,8
Wmm
16 5/8 22 517 490
20,8 13/16 27,5 564 910
W a a L �mm ” mm mm gr
278 NLLong T-handle spark plugwrenches with jointed socket– Hexagonal opening– Rubber gasket for retaining
the spark plug– Removable sliding bar
18 3/8 275 721
24 3/8 275 721
capacity y L �Nm ” mm gr
279 TNTorque limiters for spark plugs– For controlled tightening– To be used with 3/8” spark plug sockets– Click-mechanism– Automatic reset– Tolerance: ±7%
2 short - long sockets 279 3/8”/16-16L
1 torque limiter (18 Nm) 279 TN/18
pcs description art./size
279 3/8” K18Assortment for 16 mm spark plugs– Supplied in plastic tray � 1,1 Kg
1 extension 236 3/8”/250
1 short socket 279 3/8”/20,8
1 torque limiter (24 Nm) 279 TN/24
pcs description art./size
279 3/8” K24Assortment for 20,8 mm spark plugs– Supplied in plastic tray � 1 Kg
CAP_15_GB_p326-337 4-10-2005 16:05 Pagina 331
332
TOOLS FOR CAR REPAIR CYLINDER HEAD AND PISTONS
CYLINDER HEAD AND PISTONS
6 285 310
9 285 310
ø L �mm mm gr
279 PPliers for spark plug caps– For disconneting deep-seated caps of spark
plugs– No damage to leads– Suitable for extracting small hoses
198 195
L �mm gr
279 PCPliers for spark plug caps– For disconneting caps of spark plugs– No damage to leads
150 28
L �mm gr
993 CBrush for spark plugs– For cleaning electrodes– Model with brass wires
7 23 24 60 64
7L 23 64 100 74
9L 23 64 100 85
10 23 24 60 70
10L 23 64 100 82
12L 23 64 100 117
14L 23 64 100 152
16L 23 64 100 188
n° a b L �ø mm mm mm gr
233 1/2” NSSockets for splinedhexagonal screws(RIBE)– 1/2” square drive
b
6L1 23 210 250 145
7L1 23 210 250 145
8L1 23 210 250 145
n° a b L �ø mm mm mm gr
233 1/2” PSSockets for splinedhexagonal screws(RIBE)– Long model– 1/2” square drive– For rocker cover screw– FIAT Bravo - Brava
b
Check the online catalog on the Usag web site. You will findinstructions for use and technical information about USAG products.www.usag-tools.com
CAP_15_GB_p326-337 4-10-2005 16:05 Pagina 332
333
TOOLS FOR CAR REPAIRCYLINDER HEAD AND PISTONS
235 350
L �mm gr
874Valve guide seal pliers– For removing valve guide seals
75÷225 380 1,2
capacity L �mm mm Kg
438/1Valve lifter clamp– Screw adjustment model, straight
clamps for fitting and removing valvesprings
390 130 1,4
capacity L �mm mm Kg
438 NSlide-hammer valve lifter– For removing valve springs– The slide hammer is used to free split
collets
350 90
L �mm gr
905 AAntifreeze hydrometer– Measures antifreeze levels in engine
coolant– Two scales: for cold or warm engines
905 CRefractometer– Instant check of battery charge or coolant freezing
point of coolant and windshields cleaning fluid– Temperature-compensated readings– Reading range: Coolant 0 ÷ -48°C
(Precision: +/- 0,55°C)Battery fluid specific gravity: 1.1÷1.4 Kg/l(precision: +/- 10%)Windshields cleaning fluid: 0÷-40°C
– Supplied with wallet, sampling pipette and servicescrewdriver
� 445 gr
CAP_15_GB_p326-337 4-10-2005 16:05 Pagina 333
334
TOOLS FOR CAR REPAIR CYLINDER HEAD AND PISTONS
1 60÷125 80 268
2 90÷175 80 298
2L 90÷175 165 627
n° service capacity L �ø mm mm gr
430Piston ring compressors– To hold piston rings steady in their positions while
inserting the pistons into the cylinders– Supplied with key
1 55÷110 80 230
2 100÷160 80 350
n° service capacity L �ø mm mm gr
430 CRatched ring compressors– To hold piston rings steady in their positions while
inserting the pistons into the cylinders– Supplied with key
1 55÷100 210 299
2 80÷120 230 350
3 110÷160 250 521
n° capacity L �ø mm mm gr
437Piston ring pliers– Model with specially
shaped jaws forassembling anddisassembling piston rings
438 NA1Collet clamp– For 16-valve engines– For use with puller 438 N
� 75 gr
439 PAir-operated valve grinder– Air supply pressure 8 bar– Air consumption 80 L/min.– Adjustable oscillation rate: 250÷3000/min– Supplied with 3 suction pads: Ø 22, 33 and 45 mm
� 800 gr
22 17
33 28
45 31
ø �mm gr
439 PASuction pads
225 27
L �mm gr
439 MValve grinder– Suction pads Ø 19 e 22 mm
CAP_15_GB_p326-337 4-10-2005 16:05 Pagina 334
1510 VScrew caps
1510 BBayonet caps for vehicles
335
TOOLS FOR CAR REPAIRCYLINDER HEAD AND PISTONS
1510Cooling system tester– Checks cooling system tightness (hoses, clips,
pump, radiator, cylinder-head gasket)– Supplied in plastic case with pump, pressure gauge
and screw cups
a 445x335x95 � 2,1 Kg
1510 SBayonet cap adaptor
1510 PPump with pressure gauge
1 BMW
2 BMW - FORD - OPEL - VOLKSWAGEN/Passat
3 CITROEN - FIAT - PEUGEOT - RENAULT - VOLVO
4 VOLKSWAGEN
5 VOLKSWAGEN - AUDI - SEAT - SKODA
6 VOLKSWAGEN - SEAT
n° cars
– For tester 1510
1 Cars
2 Industrial vehicles
3 Japanese cars
4 Japanese cars
n° cars
– For tester 1510
CAP_15_GB_p326-337 4-10-2005 16:05 Pagina 335
14,5÷25 130 130
capacity L �mm mm gr
485Clutch disk aligner– For centering clutch disks on the pressure plate – Supplied with three expansion pliers 485 R (A-B-C)
336
TOOLS FOR CAR REPAIR MAINTENANCE
HOSE PLIERSThese pliers can be adapted to any hose, they arecompact and easy to use even with one hand;useful to fasten the hose, to turn or disconnect itand remove it from its support.Available in two versions for car or industrialvehicles and heavy-duty purposes.
MAINTENANCE
870 AHose pliers for cars– To clamp and disengage rubber hoses without
damage– Composed by body and mobile claw that can suit
to hoses from Ø 24 to 53 mm.
� 345 gr
870 BHose pliers for industrial vehicles– To clamp and disengage rubber hoses without
damage– Composed by body and mobile claw that can suit
to hoses from Ø 48 to 115 mm.
� 700 gr
20÷75 250 821
capacity L �ø mm mm gr
876Adjustable log-grip pliers– For cutting exhaust pipes for partial
replacements
876 ASpare chain A 14,5÷18 6
B 18÷21 8
C 22÷25 8
n° capacity �mm gr
485 RSpare expansion pliers
CAP_15_GB_p326-337 4-10-2005 16:05 Pagina 336
878 AHose clamps– Hoses are clamped shut instantly
without damage
8÷15 160 170
15÷28 180 190
25÷55 205 210
Ø L �mm mm gr
692 SP1Assortment of 5-points bits– Set of bits with internal hole to
disassemble air mass gauges andinjection pumps
– Composed by a bit holder (1/4” - 5/16”) and 7 bits(TS-10 / TS-15 / TS-20 / TS-25 / TS-27 / TS-30 /TS-40)
337
TOOLS FOR CAR REPAIRMAINTENANCE
871 APliers for CORBIN clamps– For cooling, heating and fuel hoses– Facilitates quick operations without disassembling
any obstructing part– To reduce efforts thanks to the rack-type system– Suitable to rings from 18 to 54 mm.
871 BCLIC spring-clips pliers– To remove and reassemble CLIC spring-clips– Pivoting jaws for an easy access to the CLIC
spring-clip
Y
15÷62 190 190
capacity L �ø mm mm gr
129Pliers for external snap rings– Special jaws for working on snap rings or stop
rings (BNA R.92.01 standard)
22 1/2 30 85 195
22 L 1/2 30 110 222
W Y a L �mm ” ø mm mm gr
875Socket wrenches for lambda probes– For installing or removing lambda
probes in vehicles fitted with acatalyzer
– Hexagonal opening
220 95 310
L opening �mm max mm gr
871Pliers for CORBIN clamps– Model with choice of axial or 90° grip that can be
blocked in three different positions
Y
285 45 350
L opening �mm max mm gr
871/2Pliers for CORBIN clamps– Model with device for adjustment and blocking of
the jaw opening– Pegs that turn up to 180° to allow a grip in all
working conditions
Y
CAP_15_GB_p326-337 4-10-2005 16:05 Pagina 337
338
TOOLS FOR CAR REPAIR MAINTENANCE
870Spring-clips pliers– For hose clips on cooling,
heating, fuel ect.
� 400 gr
870/1Spring clip pliers– For hose clips on cooling,
heating, fuel, etc.– Supplied with blocking
system and pivoting tips– Long model
� 395 gr
870/2Spring clip pliers– For hose clips on cooling,
heating, fuel, etc.– Supplied with blocking
system and pivoting tips
� 340 gr
889 KBNCable reel with trasformer 12 V andinspection lamp– Model with automatic cable rewind and stops that
can be inserted every 50 cm. – Shock resistant plastic body with swiveling bracket
for attachment to wall – Protection level IP 42 – 16 m. of working cable, of which 1.5 m are outside
the reel – Supplied with inspection lamp (technical
characteristics as 889A)
TRANSFORMER– Power 60 W– Supply voltage 220 V– Outputs 12 and 24 V– Manual resetting circuit breaker, located on the
secondary, prevents short-circuits and overload – Luminous switch placed on the power supply inlet
� 6,6 Kg
889 KNReel-type inspection lamp– Model with automatic cable rewind and stops that can be
inserted every 50 cm.– Shock resistant plastic body with swivelling bracket for
attachment to wall– Protection level IP 42 – 16 m. of working cable, of which 1.5 m are outside the reel– Supplid with inspection lamp– Power supply: 220 V
� 5,6 Kg
889 KRSpare inspection lamp– For 889 KN e 889 KBN
CAP_15_GB_p338-349 4-10-2005 16:08 Pagina 338
339
TOOLS FOR CAR REPAIRLUBRICATION AND FILTRATION
LUBRICATION AND FILTRATION
66 6 195
76 6 215
86 9 255
96 9 291
Ø notched �mm gr
446 TCap wrenches for oil filters– For Purflux oil and diesel filters – 3/8” square drive
65 14 65 122
66,5 14 66,5 122
74 8 74 150
74A 14 74 160
74B 15 74 160
79 15 79 175
89 15 89 200
92 10 92 185
92A 15 92 205
n° sides ø filter �mm gr
446Cap wrenches for oil filters– 3/8” square drive
50÷110 1/2 276
capacity Y �ø mm ” gr
445 KChain wrench for oil filters
60÷110 225 738
capacity L �ø mm mm gr
445Articulated chain wrench for oil filters
445 ASpare chain
60÷106 235 310
capacity L �ø mm mm gr
443 FMetallic strap wrench for oil filters– Model with rackwork adjustment
60÷140 225 230
capacity L �ø mm mm gr
444Strap wrench for oil filters
444 ASpare strap– Model with chain and socket
– Chain model, with joint
– Model with synthetic strap
CAP_15_GB_p338-349 4-10-2005 16:08 Pagina 339
340
TOOLS FOR CAR REPAIR LUBRICATION AND FILTRATION
66÷106 290 340
capacity L �ø mm mm gr
443Fast oil-filter wrench– Stainless steel strap wrench– Sprung hinged jaws for gripping the filter and
having a ratchet effect– Reinforced composite handle in high resistant
plastic material (hydrocarbons, bumps) – Multi-thread fast-adjustment screw
443 ASpare strap
65÷105 290 376
capacity L �ø mm mm gr
443 BMetallic strap wrench for oil filters– Model for cars
105÷145 300 325
capacity L �ø mm mm gr
443 BCMetallic strap wrench for oil filters– Model for industrial vehicles
443 BASpare strap
443 BCASpare strap
65÷120 3/8 760
capacity Y �ø mm ” gr
446 ASelf-gripping oil-filter wrench– Model for cars
95÷165 1/2 1235
capacity Y �ø mm ” gr
446 CSelf-gripping oil-filter wrench– Model for industrial vehicles
446 MTool for Multijet diesel filterSupplied with:– 1/2 drive for torque wrench– Adapter for vice
� 525 gr
CAP_15_GB_p338-349 4-10-2005 16:08 Pagina 340
341
TOOLS FOR CAR REPAIRLUBRICATION AND FILTRATION
1 square drive socket 263
1 double-ended square drive wrench 263 A y 8x10 mm
1 double-ended square drive wrench 263 A 10x11 mm
1 double-ended square drive wrench 263 A 12x13 mm
1 double-ended square drive wrench 263 A 14x17 mm
1 double-ended square drive wrench 263 A 5/16x3/8”
pcs. description art./size
263/S6Set of oil plug wrenches (6 pcs)– Supplied in sheet steel box
a 185x40x30 mm � 525 gr
a
a
a
a
1/2 40 78
Y L �
” mm gr
263Square drive socket– Model with retaining spring to grip the double-
ended square drive wrench
8x10 CITROEN-HONDA- 32 39
PEUGEOT-RENAULT
10x11 FIAT-LANCIA-FORD 32 43
12x13 VW-AUDI-BMW-MERCEDES 32 46
14x17 OPEL 32 56
5/16x3/8 FORD 32 37
n° Makes L �mm gr
263 ADouble ended square drive wrenches for oil plugs– For use in combination with square drive socket 263
y
a
a
a
a
10 29,5 35
Y L �mm mm gr
263 FDrain plug socket with female square– 3/8” square drive
8 29,5 30
10,5 29,5 34
y L �mm mm gr
263 QDrain plug socket with male square– 3/8” square drive
10 30 32
v L �mm mm gr
263 TDrain plug socket with male triangle– 3/8” square drive
16 55 158
for screw L �M mm gr
263 XZNDrain plug socket with XZN male– 1/2” square drive– AUDI gearbox
CAP_15_GB_p338-349 17-11-2005 11:37 Pagina 341
342
TOOLS FOR CAR REPAIR LUBRICATION AND FILTRATION / ELECTRICAL AND BATTERY
ELECTRICAL AND BATTERY
12 225 285
a L �mm mm gr
264 TOil plug wrench, gearbox– ALFA ROMEO, FIAT, LANCIA
8x10 230 240
y L �mm mm gr
264/1Drain plug wrench– CITROEN, RENAULT, PEUGEOT
1870Oil pressure tester– Quick coupler connection– Range: 0÷8 bar– Supplied in plastic case complete with adaptors,
seals and fittings
a 360x340x130 mm � 2,1 Kg
891 K
Battery diagnosis:– Checks 6 and 12 V batteries in few seconds whether
in stock or mounted in the vehicle– Measures current in Volt and the distribution of CCA
current according to the standard selected by theuser
– Checks battery charge even when completelyuncharged
– Does not damage the central power unitDiagnosis of charging and starting systems:
– Measures currents from 1 to 30 V for diagnosingalternators, diodes and regulators at different values
– Makes diagnosis of the efficiency of the choke andthe starter engine
– Immediate printing of test results– Supplied in plastic case
a 185x100x35 mm � 420 gr
Battery diagnosis 6 e 12 V
Charge system 12 e 24 V
Voltage measures 1 - 30 V
Uncharged battery test up to 1,5 V
Battery capacity up to 200 Ah
CCA Precision +/- 5%, resolution 1 A
Display LCD, 2 x 16 caratteri
Printer incorporated
CCA (standard) SAE: 40-2000 A
ENc1: 50-2500 A
ENc2: 40-2100 A
IEC: 30-1500 A
DIN: 25-1300 A
Working temperature 0-50°C
Supply 4 internal batteries 1,5 Volts
(type LR6-AA), range 800 prints
Technical characteristics
Digital battery tester with printer
891 KEDigital battery tester with printer(English software)
CAP_15_GB_p338-349 4-10-2005 16:08 Pagina 342
343
TOOLS FOR CAR REPAIRELECTRICAL AND BATTERY
890Battery tester– For measuring battery charge, with turned-off
engine, with results within 5 sec– Reading scale of 6 and 12 V– For checking the functioning of the alternator
� 540 gr
1613Portable start booster for cars (12 V/1600 A)– Supplied with charger for power grid and cigarette
lighters
TECHNICAL CHARACTERISTICS– The battery of the 1613 gives a 1.600 A starting
current– 400 A clamps with 6-wire copper cable– Multifunctional power supply. Use with the cigarette
lighter or connected to the power grid– Protection with 20 A automatic reset breaker– Charge test button with LEDS– Protection circuits againt peak tensions, protects
the vehicle electronic system– The sealed battery (12 V/16 Ah) protects against
electrolytic leak– Possibility to place and/or use it in every position
USES– As battery charger– For emergency starter– As an additional power source for vehicles (to save
the memories)– Multipurpose additional energy source (for
electrical 12 V devices)
� 10 Kg
1881Assortment for BOSCH alternators– For assembling and disassembling pulleys of
BOSCH alternators– Supplied in plastic box
a 275x80x40 mm
� 500 gr
261 NMagneto wrenches– Set composed of eight open jaw wrenches,
a feeler gauge, a blade for slot-head screws,a file
4 - 4,5 - 5 - 5,5 - 6 - 6,5 - 7 - 7,5 47
a �mm gr
892Cleaner for clamps and battery terminals– For removing deposits– Steel bristles
� 50 gr
1 Male key 1881 A
1 Long Torx bit T50 1881 C
1 Long XZN bit M10 1881 B
1 Bit holder scket 1881 D
2 Special sockets 1881 E-F
pcs. description art./size
CAP_15_GB_p338-349 4-10-2005 16:08 Pagina 343
344
TOOLS FOR CAR REPAIR WHEELS, STEERING AND HUBS
500 50
1000 96
capacity �ml gr
892 DBattery fillers– Made of acid-resistant, oil-resistant and solvent-
resistant plastic
280 85
L �mm gr
892 ESuction pump for battery liquid
350 260
L �mm gr
905 BNAcyd hydrometer for batteries– Measures the density of the battery liquid
WHEELS, STEERING AND HUBS
270 CSockets for tyre rims– With nylon protection to prevent tyre rims from
being damaged– Sizes: 17-19-21 mm
270 C/S3Set of sockets for tyre rims (3 pieces)– Supplied with 3 sockets 270 C (17-19-21 mm)
a 175x130x50 mm � 852 gr
27x30 40x44 600 435 3,1
27x32 40x47 600 435 3,2
30x33 44x49 600 435 3,3
W a b L �mm ø mm mm mm Kg
271T-handle wrenchesfor wheel nuts– For industrial vehicles– Removable sliding T-handle
17 230
19 230
21 257
a �mm gr
CAP_15_GB_p338-349 4-10-2005 16:08 Pagina 344
345
TOOLS FOR CAR REPAIRWHEELS, STEERING AND HUBS
3 17x19x22xy1/2” 25x28x32 395 1,2
5 17x19x21xy1/2” 25x28x30 395 1,5
n° W a L �mm ø mm mm Kg
272Cross-type wheel nutwrenches– For cars and light industrial
vehicles– Hexagonal openings– 1/2” interchangeable
square male
1 24x27x30x32 35x39x42x45 700 4,6
3 24x27x32xy3/4” 36x39x46 700 4,4
4 24x27x33xy3/4” 36x39x46,5 700 4,2
n° W a L �mm ø mm mm Kg
272 CACross-type wheel nutwrenches– For heavy industrial
vehicles– Hexagonal openings– 3/4” interchangeable
square male
1/2 40
3/4 50
y �
” gr
272 QSpare square male
80 10
L �mm gr
3181Valve extractor– For tire inflation valves
36 3/4 46 36 280
W Y a L �mm ” ø mm mm gr
271 MHub-nut socket– Hexagonal opening
36 3/4 46,8 100 730
W Y a L �mm ” ø mm mm gr
271 MLImpact sockets– Hexagonal opening– For hub-nuts– FIAT - LANCIA - ALFA ROMEO
225 110 27 4
capacity depth a �ø max mm max mm mm Kg
450Puller for wheel hubs– Model with four oscillating
removable legs for detachingwheel hubs from cars
– Supplied with service wrench
450 ASpare leg
CAP_15_GB_p338-349 4-10-2005 16:09 Pagina 345
346
TOOLS FOR CAR REPAIR WHEELS, STEERING AND HUBS
250 455
L �mm gr
425Wheel weight pliers– For fitting and removing wheel balancing weights
and for loosening or compressing the retainingsprings
300 206
400 411
500 611
600 868
L �mm gr
427Tyre bead removers– Double T-section to ensure maximum resistance
16 45 100 50 635
22 45 100 56 665
32 80 158 75 2452
capacity a L a �ø mm mm mm mm gr
449Ball-joint extractors– For extracting ball joints from
steering wheel andsuspensions
16÷18 40 40 19 410
20÷22 40 40 19 425
capacity a b a �ø mm mm mm mm gr
449/1Ball-joint separators– For removing steering and suspension
ball-joints
16÷18 50 45 19 700
20÷22 50 45 19 700
25 60 55 24 700
capacity a b a �ø mm mm mm mm gr
449/2Ball-joint separators– For removing steering and suspension
ball-joints
36 8 65 210 6,6
capacity max power a L �ø mm t mm mm Kg
449 IDHydraulic ball jointsseparator– For extracting ball-joints from
steering wheel and suspensionson industrial vehicles
CAP_15_GB_p338-349 4-10-2005 16:09 Pagina 346
347
TOOLS FOR CAR REPAIRBRAKES
BRAKES
bar bar
2845Brake pressure tester– For testing compensator operating pressure and
diagonally-split brake systems– Max pressure: 200 bar– Accuracy: 1%– Inside hose Ø 2 mm– Length: 1 x 3,0 m / 1 x 5,0 m– Supplied in plastic case with two pressure gauges
and adaptors
a 375x270x75 mm � 2 Kg
1 plier 2800
1 adapter for closed bars 2800 A/1
1 adapter for closed bars 2800 A/11
6 flanges 2800 A/2-3-4-5-8-9
pcs. description art./size
2800 S8Pliers and flange set– The plier enables to windsback pistons on
calipers with integral hand brake– The built-in ratchet (clockwise and
counterclockwise) saves repositioningoperation
2843Brake fluid tester– For testing the efficiency of brake system
according to the water concentration inside thebrake fluid
– Suitable for all DOT types – Powered by a 9 V battery (included) – Alarm LED signaling brake liquid contamination
� 245 gr
2800 CAdaptor – For CITROËN BX
� 200 gr
2800 BAdapter – For Peugeot J7- J9 and
Renault Espace TD– For front-brake caliper
pistons (DBA type)
� 170 gr
BRAKE CIRCUITPRESSURE GAUGE 2845
Good braking system performance is one of thefundamental points for road safety and one of the mostfrequent causes for failing car inspections.2845 tool makes precise diagnosis of brake circuitpressure.
CAP_15_GB_p338-349 29-11-2005 11:31 Pagina 347
348
TOOLS FOR CAR REPAIR BRAKES
2847Brake bleeder with trolley– Supplied with flexible hose (4 m.), cables (4 m.),
6 plugs (2847 A/S5 set and universal plug),reutilization tank
– Power supply 12 V with battery terminal pliers– For changing, filling and bleeding the circuits of
brakes and hydraulic clutch– Peristaltic pump, no direct pump/liquid contact, no
air pressure on liquid, no emulsion risk– Pressure sensor/limiting device set at 2 bar
(for ABS too)– Possibility of filling the circuit during the bleeding– Automatic pump turning on/off according to
pression variations– Capacity: 5 litres– Portable and “self-governing”
� 16 Kg (with full tank)
2847 A/S5Assortment of 5 plugs– To use with brake bleeder 2847 (already enclosed
in brake bleeder 2847)
2847 A/S13Assortment of 13 plugs – To use with brake bleeder 2847
2847 A/6Universal plug– To use in combination with brake bleeder 2847
(already enclosed in brake bleeder 2847)
240 34 205
L ø �mm mm gr
441 ESteady-spring tool– Fits steady-spring caps
for compression againstdrum-brake shoes
– All makes
230 180
L �mm gr
441 FHand-brake pliers– For easy hook-up of hand-brake cable
225 288
L �mm gr
441/0Brake spring pliers– For attaching or
detaching the retractingsprings of drum brakeswith bonded brake-shoeson cars
– Knurled and hingedanchor-plate
220 244
L �mm gr
441/1Brake spring pliers– For attaching or detaching the retracting springs of
drum brakes with riveted brake-shoes on cars
CAP_15_GB_p338-349 4-10-2005 16:09 Pagina 348
1 spring compressor 447 P
2 pairs of forks 447 P1-P2
pcs. description art./size
447 P/SE3Shock absorber spring assortment (3 pcs.)– Supplied with three spare pins 447 PA � 13 Kg
349
TOOLS FOR CAR REPAIRSUSPENSION AND TRANSMISSION
345 473
L �mm gr
441/2Brake spring pliers– For attaching or detaching the retracting springs of
drum brakes with riveted brake-shoes on cars– Serrated and hinged anchor-plate
230 13,5 580 22 5,5
opening power L a �max mm max ton max mm mm Kg
447 PSpring compressor for shock absorbersprings– For use in combination with forks
447 P1÷7 for fitting ordisassembling coil springs on MacPherson shock absorbers
– Body with telescopic arms– Safety pin against accidental
overloads (tensile stress 140 Nm)– Can be used with electric or
impact wrenches
SUSPENSION AND TRANSMISSION
447 PASpare safety pin
1 y 95÷157 3,9
2 y 120÷180 4,0
3 y 138÷215 4,7
5 y 65÷125 3,3
6 y 170÷195 4,3
7 y 145÷170 5,0
n° colour capacity �ø mm Kg
447 PGForks– Shaped model for the
maximum safety
490 1,2
L �mm Kg
441/3Brake spring pliers– For attaching or detaching the retracting springs of
drum brakes with bonded brake-shoes on industrialvehicles
– Knurled and hinged anchor-plate
225 90
L �mm gr
993 BBrush– For cleaning disk brake-shoes – Steel bristles
1 spring compressor 447 P
3 pairs of forks 447 P1-2-3
pcs. description art./size
447 P/SE4Shock absorber spring assortment (4 pcs.)– Supplied with three spare pins 447 PA � 18 Kg
CAP_15_GB_p338-349 17-11-2005 11:39 Pagina 349
160 277
L �mm gr
872 ANPliers for metal hose clamps– For use with clamps 872 D and clips 872 C to
secure sleeves, bellows and rubber caps overhomokinetic joints of axle-shafts
350
TOOLS FOR CAR REPAIR SUSPENSION AND TRANSMISSION
270 24 365 2,1
capacity max a L �mm mm mm Kg
447Pressers for shock absorber springs– For fitting or disassembling coil springs on car
shock absorbers – Double hook and antislip locking screw
315 2,9
L �mm Kg
447 PMVice for absorberuprights– For clamping shock
absorber to workbench
447 USet of 5 flare-nut wrenches - for VW– For loosing and tightening notched nuts or strud
rods
� 70 gr
1 plier for hose clamps 872 AN
100 clips 872 C/5
1 metal hose clamp with plastic cover 872 D
pcs. description art./size
872 NMetal straps set in plastic case (102 pcs)– For secure sleeves, bellows and rubber caps over
homokinetic joints of axle-shafts– Supplied with plastic case
a 265x225x50 mm � 1,2 Kg
5 50 562
10 25 583
strap width L �mm mm gr
872 BSpare hose clamps
5 0,5
10 2
for strap �mm gr
872 CClips
CAP_15_GB_p350-359 4-10-2005 15:57 Pagina 350
351
TOOLS FOR CAR REPAIRBODYWORK
3210Instrument for protecting the cental powerunit– Protects electronic units from tension peaks which
can occur during welding operations – ON/OFF led signal – Power supply: 12 V– 12 months guarantee
1612Memory protector– Saves configuration and stored data of electronic
vehicle accessories when the battery is beingchanged or power is temporarily interrupted
– Power supply: 12 and 24 V– 12 months guarantee
� 225 gr
BODYWORK
422 AHorizontal stand– Model with 3 supporting points– Adjustable heigth (800-1100 mm)– Width (500÷1000 mm)
� 5 Kg
5 0,8 12 290 1,2
hole thickness fold L �ø mm max mm mm mm Kg
215 BPanel punching andfolding pliers– Model with swivel head for
piercing and folding the edgesof sheet steel to be welded
215 RSpare die and punch
200 25 220
L a �mm mm gr
353 LSide- and end-cutting chisel
CAP_15_GB_p350-359 4-10-2005 15:57 Pagina 351
352
TOOLS FOR CAR REPAIR BODYWORK
40 18 160 320 565
a b c L �ø mm mm mm mm gr
392Hammer with flatround and curvedchisel heads
25 100 32 290 360
a b c L �ø mm mm mm mm gr
393Hammer with flat roundand flat square heads
25 100 32 280 293
35 100 40 280 353
a b c L �ø mm mm mm mm gr
393 ZGHammers with serratedround and flat squareheads
32 27 110 280 320
a b c L �ø mm mm mm mm gr
413 BHammer with roundflat head andhorizontal chisel peen
70 50 30 310 320
a b c L �ø mm mm mm mm gr
414 AHammer with flatrectangular head
44 13 135 310 380
a b c L �ø mm mm mm mm gr
415 AHammer with a flat roundhead and a straightpointed peen
CAP_15_GB_p350-359 4-10-2005 15:57 Pagina 352
353
TOOLS FOR CAR REPAIRBODYWORK
44 20 160 310 420
a b c L �ø mm mm mm mm gr
415 BHammer with flat roundhead and straight ballpeen
56x56x56 0,8
sizes �mm Kg
396Dolly with round convex and flat head
76x57x58 1,2
sizes �mm Kg
397Rail shaped dolly
83x63x36 1,0
sizes �mm Kg
398Heel shaped dolly
115x56x25 0,8
sizes �mm Kg
399Convex shaped dolly
120x58x28 1,2
sizes �mm Kg
399 ZGConvex shaped serrated dolly
90x70x125 1,4
sizes �mm Kg
400Dolly with two convex heads
CAP_15_GB_p350-359 4-10-2005 15:57 Pagina 353
354
TOOLS FOR CAR REPAIR BODYWORK
140x54x55 1,3
sizes �mm Kg
401Comma shaped wedged dolly
106x65x26 0,8
sizes �mm Kg
401 ALarge grooved dolly
125x54x44 0,7
sizes �mm Kg
403Hand dolly with convex round headand peen
sizes �mm Kg
405“C” shaped dolly
102x72x62 1,4
sizes �mm Kg
406Anvil shaped dolly
110x62x28 0,8
sizes �mm Kg
407Wedge shaped dolly
400 1,2
L �mm Kg
408Double spoon with one grooved blade
250 0,5
L �mm Kg
40940° curved spoon
102x72x62 1,6
CAP_15_GB_p350-359 4-10-2005 15:57 Pagina 354
355
TOOLS FOR CAR REPAIRBODYWORK
510 2,2
L �mm Kg
410Double spoon with one flat blade and a curved one
400 1,7
L �mm Kg
410 CDouble spoon with one curved blade and a flat one
390 1,3
L �mm Kg
411Facing narrow body spoon, long model
285 0,8
L �mm Kg
412Light curved spoon, short pattern
350 0,7
L �mm Kg
412 BFlat serrated spoon for thinning out operations
360 0,5
L �mm Kg
416 NAdjustable file holder– Screw adjustment for matching straight or curved contours– Adjustable for two lenghts: 300 and 350 mm
3,5 350 standard 288
4,5 350 fine 296
denti L cutting �cm mm gr
416 NAFlat flexible files– For use with adjustable file holder 416 N
CAP_15_GB_p350-359 4-10-2005 15:57 Pagina 355
356
TOOLS FOR CAR REPAIR BODYWORK
1 Hammer with flat round and flat square heads 393
1 Dolly with round convex and flat head 396
1 Rail shaped dolly 397
1 Heel shaped dolly 398
1 Convex shaped dolly 399
pcs. description art./size
423 N5Car body repair set (5 pcs.)– Supplied in sheet steel case
a 340x190x70 mm � 5,5 Kg
1 Mallet 376/42
1 Hammer with flat round and flat square heads 393
1 Dolly with round convex and flat head 396
1 Rail shaped dolly 397
1 Heel shaped dolly 398
1 Convex shaped dolly 399
1 Dolly with two convex heads 400
1 Comma shaped wedged dolly 401
1 Facing narrow body spoon, long model 411
1 Hammer with round flat head and horizontal chisel peen 413 B
1 Adjustable file holder 416 N
1 Flat flexible file 416 NA/3,5
pcs. description art./size
423 N12Car body repair set (12 pcs.)– Supplied in sheet steel case
a 470x310x75 mm � 14 Kg
1 Mallet 376/42
1 Hammer with flat round and curved chisel heads 392
1 Hammer with serrated round and flat square heads 393 ZG/32
1 Rail shaped dolly 397
1 Heel shaped dolly 398
1 Convex shaped serrated dolly 399 ZG
1 Dolly with two convex heads 400
1 Hand dolly with convex round head and peen 403
1 “C” shaped dolly 405
1 Anvil shaped dolly 406
1 Double spoon with one grooved blade 408
1 Double spoon with one flat blade and a curved one 410
1 Double spoon with one curved blade and a flat one 410 C
1 Facing narrow body spoon, long model 411
1 Hammer with a flat round head and a straight ball peen 415 B
1 Adjustable file holder 416 N
1 Flat flexible file 416 NA/3,5
pcs. description art./size
423 N17Car body repair set (17 pcs.)– Supplied in sheet steel case
a 600x270x130 mm � 25 Kg
CAP_15_GB_p350-359 25-10-2005 8:09 Pagina 356
357
TOOLS FOR CAR REPAIRBODYWORK
120 80 375 1,1
suction pad capacity L �ø mm max Kg mm Kg
424 N4Suction pads– For the transport and
positioning ofwindshields during fittingand removing operations
– Suction pads can be setto suit flat and curvedsurfaces
95 107
L �mm gr
424 N2Handle for windshields– For car windshield removal
1 Lever for windshields 424 N1
1 Handle for windshields 424 N2
1 Steel wire for windshields 424 N3
1 Suction pads 424 N4
1 Belt for windshields 424 N5
pcs. description art./size
424 N/SE6Windshield set for bonded windshields (6 pcs)
� 3,3 Kg
4 340
L �mm gr
424 N5Belt for windshields– For use together with suction pads 424 N4 when
fitting windshields– Ratchet type tightening device and nylon belt
345 219
L �mm gr
424 N1Lever for windshields– For use together with handle 424 N2 and steel wire
424 N3 for removing windshields
CAP_15_GB_p350-359 4-10-2005 15:57 Pagina 357
358
TOOLS FOR CAR REPAIR BODYWORK
424 TNWind-shields wiper arms remover– For removing wiper arms without damaging
bodywork
230 139
L �mm gr
426Clip remover– To exctract clips from car door panel linings
426 AFastener removal clips – To extract without damaging the fasteners securing
trims and panels
� 248 gr
18 47
L �m gr
424 N3Steel wire for windshields (round section)– For car windshield removal
426 V/S6Set of 6 suction pads– Secures bonded components while curing
� 477 gr
155 105
L �mm gr
426 GTrim removal– For removing interior door trimmings without
damage
EN 8 285 hexagonal 300
N 10 280 bi-hexagonal 162
N 12 280 bi-hexagonal 154
N 13 280 bi-hexagonal 147
N 16 285 bi-hexagonal 225
TX 40 285 295
TX 45 283 295
XZN 10 283 XZN 296
art. L shape �mm gr
431Special door-hinge wrenches– Double angled and curved wrenches for improved manoeuvrability
�
�
CAP_15_GB_p350-359 17-11-2005 11:34 Pagina 358