CRD Aeroelastic Optimization - METUyyaman/avt086/Kolonay/Ray_Kolonay_3.pdfCRD Kolonay 5 Goal of...

CRD

Kolonay 1

Aeroelastic Optimization

The Cultural and Convention CenterMETU

Inonu bulvariAnkara, Turkey

Sponsored by:RTA-NATO

The Applied Vehicle Technology Panel

presented byR.M. Kolonay Ph.D.

General Electric Corporate Research & Development CenterAnkara, Turkey Oct.. 1-5, 2001

CRD

Kolonay 2

• Introduction

• Aeroelastic Optimization- Linear Static Aeroelastic Optimization- Linear Dynamic Aeroelastic Optimization

• Trim Optimization

• Commercial Programs with Aeroelastic Design Capabilities

• Appendix B - Static and Static Aeroelastic Gradients

Presentation Outline

CRD

Kolonay 3

Motivation for Optimization• Missions of aeronautical and space vehicles are becoming increas-

ingly complex

• Identifying trade-offs among pertinent disciplines is critical inobtaining designs

• Traditional methods may not achieve a design let alone an optimaldesign

• Optimization also used to evaluate/design modifications to existingsystems

Introduction

CRD

Kolonay 4

Aircraft Design Considerations in MDA/MDO

Introduction

Distrib

ution

Sal

esM

arke

ting

Aerodynamics

Cost

Heat

Tra

nsfe

r

Acoustics

StructuresD

ynamics

Ele

cto-

Mag

netic

s

Controls

Manufacture

Maintenance

Reliability

ProducibilityRobustn

ess

MDA/MDO

CRD

Kolonay 5

Goal of Aeroelastic Optimization

• Determine the aerodynamic and structural parameters to satisfy allnecessary requirements over system service life

- Traditionally, weight and performance were main objective functions. That haschanged

•Life cycle cost, manufacturability, maintainability, etc. now equal players

- Historically, aerodynamic parameters (sweep, planform, etc.) where considered in

conceptual design

- Structural parameters considered inpreliminary design

- Recent MDO algorithms combining conceptual, preliminary and detailed design vari-

ables.

- With advent of AAW technology/active control(piezoelectrics) must also consider

some control design parameters as well (Aeroservoelastic Optimization)

- Recently nonlinear engineering analysis considered (CFD, nonlinear FEM)

Introduction

6

ary Design

ch as membrane/shellonal areas of rods andrmance is met

(28)

unction

s

n
RD
Scope of Discussion- Prelimin• Assume external geometry fixed

• Determine structural physical properties (suthicknesses, composite lay-ups, cross-sectibars) such that the desired aeroelastic perfo

• Mathematical statementMinimize/(Maximize F– vs( )) the objective f

F vs( )

Subject to the constraint condition

Z j vs( ) Z j≤ j 1 2…n,=

vsL

vs vsU≤ ≤

Aeroelastic Optimizatio
C
Kolonay

7

s, or any linear/non-uirement: that it

ent, aeroelastics tens of thousands)

us, 1000 max)

oes not imply that the responses

ar.

on
RD
- Objective function (weight, lift effectiveneslinear combination of responses, only reqreduces to a single scalar value)

- Behavioral constraints (stress, displacemresponse, flutter etc.) (can be as many a

- Allowable value for

- vector of design variables (assumed continuo

- Typically implicit functions of

e: Just because considered engineering analyses are linear d

are linear w.r.t. . In fact, they can be highly non-line

vs)

vs( )

Z j vs( )

vs) Z j vs( ), vs

vs( ) vs( )

Aeroelastic Optimizati
C
Kolonay

Not

F(

Z j

Z j

vsF(

Z j

8

athematical program-algorithms along with;

detailed Engi-)

on
RD
A Solution Approach

cient solution to (28), the classical nonlinear mng problem, can be achieved by gradient based

• Approximation concepts

• Design variable linking

• Active constraint strategies

• Move limit strategies

ective solutions to (28) should requireless than 30ering Analyses (including gradient calculations

C
Kolonay

Effimi

Effne

9

ts

s only gradients)

n matrix (difficult tos available.

vi

fvi voi–( )

vi

fxi xoi–( )

xoi2

---------------------------

on
RD
Approximation concep

• Single point or multi-point first order (requireapproximations

- 1st order Taylor Series direct space

- 1st order Taylor Series inverse space

• Second order approximations require Hessiaevaluate). Two point approximations method

f f o ∂∂

i 1=

ndv

∑+=

xi1vi----= f, f o

∂∂

---

i 1=

ndv

∑–=

C
Kolonay

CRD

Kolonay 10

Design Variable Linking(29)

• Unique linking - Single value in any given row or column of

• Group linking - Only one entry per row but may have multipleentries in a given column

• Shape function linking - Multiple entries in a row and or column

t{ } P[ ] v{ }=

P[ ]t1

t2

t3

P11 0 0

0 0 P23

0 P32 0

v1

v2

v3

=

t1

t2

t3

P11 0 0

P21 0 0

P31 0 0

v1

v2

v3

=

t1

t2

t3

P11 P12 P13

P21 P22 P23

P31 P32 P33

v1

v2

v3

=


CRD

Kolonay 11

Active constraint strategies

• Pass an “active” subset of the constraints to the approximate prob-lem

- Retain all violated constraints- Retain constraints within 10% of the boundary- Don’t retain more than 1 or 2 times NDV unless necessary

• Update the “active” set for each new approximate problem

• Calculate gradients for only the “active” set of constraints- Results in large computational savings


CRD

Kolonay 12

Move Limit Strategies• Using approximations for constraints functions, objective function,

constraint function gradients, and objective function gradientsmust be recognized by imposing constraints on the movement ofthe design variables for any given approximate problem.

• movlim is problem dependent, values typically can range anywherefrom 1.1 to 2.0

voimovlim------------------ vi movlim voi×≤ ≤


CRD

Kolonay 13

Gradient Calculations

• Efficient accurate gradient calculations areessentialto gradientbased solutions to (28).

• If at all possible avoid finite difference gradients- Costly, and prone to step size problems

• Use analytic or semi-analytic gradients


RD

14

• lastic gradientselemental level.

•

(30)

ixede )

r)

ar bnonlinearee, )

r

Gradient CalculationsFor the current scope, static and dynamic aeroedepend on the gradients of at the

Decompose the elemental matrices into 3 parts

- Invariant w.r.t. design variable

- Linear variation w.r.t.

- Non-linear variation w.r.t.

M[ ] K[ ] B[ ], ,

v{ } k fixedee

mfixedee

bfe, ,(

v{ } k factoree

mfactoree

bfactoee, ,(

v{ } knonlinearee

mnonlineee,(

K[ ] Ak fixedee

A Pisk factori

eevs

i∑

s∑ Aknonlinear

ee+ +=

M[ ] Amfixedee

A Pismfactori

eevs

i∑

s∑ Amnonlinea

ee+ +=

B[ ] Ab fixedee

A Pisb factori

eevs

i∑

s∑ Abnonlinear

ee+ +=

C
Kolonay

RD

15

th es to global - atrix in (29)

e perator)

(31)

P[ ]

le

n

e assemble operation for the elemental matricsuperscript indicating elemental matrices being the terms of the design variable linking m

rentiating (30) w.r.t. yields (A is an assembly ovs

vs∂∂

K[ ] A Pisk factoriee

i∑ A pis ti∂

∂knlee

i∑+=

vs∂∂

M[ ] A Pismfactoriee

i∑ A pis ti∂

∂mne

i∑+=

vs∂∂

B[ ] A Pisbfactoriee

i∑ A pis ti∂

∂bnlee

i∑+=

Aeroelastic Optimizatio
C
Kolonay

A - -

Diff

eePis

16

rward finite dif-

(32)

i-analytic∇

on
RD
th by fo

ence as

fully analytic, sem

∂knlee( ) ∂ti( )⁄ ∂mnl

ee( ) ∂ti( )⁄ ∂bnlee( ) ∂ti( )⁄, ,

ti∂

∂knlee

n

kee

nti ∆ti+( )n

kee

n–

∆ti-----------------------------------------------------------=

ti∂

∂mnlee

n

mee

nti ∆ti+( )n

mee

n–

∆ti--------------------------------------------------------------=

ti∂

∂bnlee

n

bee

nti ∆ti+( )n

bee

n–

∆ti------------------------------------------------------------=

nonlinearee

0= xxnonlinearee

0≠

C
Kolonay

Wi

fer

xx

CRD

Kolonay 17

Aeroelastic Constraints Considered

• Static Aeroelastic Constraints- Stress- Strain- Displacement- Flexible stability derivatives (lift effectiveness, control surface effectiveness, etc.)- Aileron effectiveness- Free trim parameter constraints

• Dynamic Aeroelastic Constraints- Flutter


CR

D

Ko

lon

ay

18

Aeroelastic O

ptimization

INITIAL DETAILED ANALYSES

Evaluate screen constraints and the objective function

SENSITIVITY ANALYSES

Find necessary objective and constraint gradients

APPROXIMATE PROBLEM GENERATOR

Uses information determined in previous two steps to create

approximate functional values and gradients

END

DETAILED ANALYSES

Evaluate constraints and the objective function

OPTIMIZATION ALGORITHM

Finds optimal weight of approximate problem, calls approxi-

mate problem for objective values, constraint values, constraint

CONVERGENCE CRITERIA

Optimization Algorithm Flow

CRD

Kolonay 19

Requirements for Optimization Environment• Multiple Boundary Conditions considered simultaneously

- Symmetric- Anti-symmetric- Asymmetric- Store configurations

• Multiple disciplines considered simultaneously- Statics- Dynamics- Static Aeroelasticity- Dynamic Aeroelasticity

• Ability to construct constraints and objective functions from avail-able responses


CRD

Kolonay 20

Von Mises Stress/Tsai-Hill Constraint

• - Element normal, transverse, and shear strains

• - Normal, transverse and shear allowables.

- - each may be compression or tension allowables depending on

the sign of

- need not be equal

gσxSx------

2 σy

Sy------

2 σxσy

SxSy-------------–

τxyFs-------

2

+ +

12---

1–=

σx σy τxy, ,

Sx Sy Fs, ,

Sx Sy, Sc St,

σx σy,

Sc St,

Static Aeroelastic Optimization

CRD

Kolonay 21

Principal Strain Constraint

with

• Fiber and transverse strain constraints often used as well

g1εx

εall--------- 1–=

g2εx

εall--------- 1–=

εx12--- ε1 ε2 ε1 ε2–( )

2 ε122

+[ ]1 2⁄

+ +=

εy12--- ε1 ε2 ε1 ε2–( )

2 ε122

+[ ]1 2⁄

–+=


CRD

Kolonay 22

Displacement Constraints

• - Weighting factors on and user specified limit respectively

• Enables specifying limits of the shape of the displacements- Wing tip twist constraint

-

Aij ujj 1=

ndisp

∑ δiall≤

Aij δi, uj

wLE wTE–

Ctip--------------------------- 0.04 radians≤


CRD

Kolonay 23

Aileron Effectiveness Constraint

With

- Rolling moment about the aircraft centerline

- Aileron deflection

- Roll rate nondimensionalized by wing span and aircraft velocity

- Flexibility effects are included in the derivatives

• Steady roll rate achievable for a unit value of aileron deflection.

εmin εeff εmax≤ ≤

εeff

Clδa f

Cl pb2V-------

f--------------------–=

Cl

δapb2V-------

f


CRD

Kolonay 24

Flexible Stability Derivative Constraint

• Enables constraint of any flexible derivative in any axis for anytrim parameter

• For example, lift effectiveness

∂CF∂δtrim----------------

lower

∂CF∂δtrim----------------

∂CF∂δtrim----------------

upper

≤ ≤

εmin

CLα fCLαr

------------- εmax≤ ≤

Static Aeroelasticity

CRD

Kolonay 25

Trim Parameter Constraint• Any FREE parameter in the trim solution can be constrained

• Angle of attack, control surface deflection etc.

δtrim δtrimreq≤ or δtrim δtrimreq

≥


CRD

Kolonay 26

Frequency Constraints

• Constraint actually on the eigenvalue (improves accuracy of

approximation)

f i f high≤ g⇒ 14π2 f high

2

λi-----------------------–=

f i f high≤ g⇒4π2 f low

2

λi--------------------- 1–=

λi

Dynamic Aeroelastic Optimization

CRD

Kolonay 27

Flutter Constraint• Constraint is formulated in terms of satisfying requirements on the

modal damping values at a series of specified velocities

• Advantages of constraining damping- No need to calculate flutter velocity- Able to capture “hump” modes

• Disadvantage- modal damping is only estimated away from the axis for P-K solution

γ ij γ jREQ≤( ) j 1 2 …nvel, ,=

Dynamic Aeroelasticity

Velocity

Original

Desired

λ

CRD

Kolonay 28

Rectangular Wing Example

X

Y

Z

X

Y

Z

Static Aeroelasticity

Material PropertiesE = 10.E06 psiPoisson’s Ratio =.3

Weight Density 0.1 lb/in3

Tensile Strength = 20.0 ksiCompressive Strength 15 ksiShear Strength 12.0 ksi

4”

60”

30”

20

75”

5”

10” 20% chord elevator

aileronStructural Model

CRD

Kolonay 29

Rectangular Wing Example• Flight Conditions

- Symmetric

- Anti-symmetric

• Constraints- Maximum Tip Rotation (Degs)- 1.0- Maximum Lift Effectiveness - 1.60- Minimum Aileron Effectiveness.30

-

M 0.8 q, 6.5 psi nz, 8.0g QRATE = 15.7 deg/sec,= = =α FREE= ELEV = FREE,

M 0.8 q, 6.5 psi aileron = 1.0 deg QACCEL = 0.0, ,= =PRATE = FREE

σT 20 ksi≤

σC 15 ksi≤

τxy 12 ksi≤


• Design Variables- Inboard top skins- Inboard bottom skins- Outboard top skins- Outboard bottom skins

• Objective Function- Weight

CRD

Kolonay 30

Rectangular Wing Example

• Four Design Cases Run

ConstraintCase

A B C D

Maximum Tip Rotation 1.0 1.0 -- 1.0

Maximum Lift Effectiveness -- 1.6 -- 1.6

Minimum Aileron Effectiveness -- -- 0.30 0.30

Stress Constraints Applied yes yes no yes


CRD

Kolonay 31

Rectangular Wing Example• Design Run Results

ParameterCase

A B C D

Inboard Top Skin Thicknesses 0.13377 0.18559 0.1166 0.18559

Inboard Bottom Skin Thicknesses 0.13377 0.18532 0.1166 0.18532

Outboard Top Skin Thicknesses 0.08254 0.05274 0.06910 0.05274

Outboard Bottom Skin Thicknesses 0.08256 0.05276 0.06910 0.05276

Structural Weight (lb) 22.71 22.98 22.35 22.98

Tip Rotation (deg) 1.0 1.0 1.68 1.0

Lift Effectiveness 1.92 1.60 2.09 1.60

Aileron Effectiveness 0.312 0.314 0.30 .314

Trimmed Angle of Attack (deg) 1.03 1.30 0.933 1.30

Trimmed Elevator Setting (deg) -2.03 -2.13 -1.96 -2.13


CRD

Kolonay 32

Intermediate Complexity Wing (ICW) Example


X

YZ

X

YZ

X

YZ

X

YZ

Structural Model Structures and Aerodynamics Models

CRD

Kolonay 33


Orthotropic MaterialE1 = 19.9E6 psi

E2 = 1.5E6 psi

G12 = 0.85E6 psi

lb/in3

Ply = 0.04 in.

Isotropic MaterialE = 10.5E6 psi

lb/in3

= 0.04 in.

ν12 0.32=

ρ 0.055=tmin

εT 4500µ≤

εC 3200µ≤

ν 0.30=ρ 0.10=tmin

σT 45 ksi≤

σT 45 ksi≤

τxy 45 ksi≤

Stress Constraints110 Von Mises Stress (rods&shear panels)256 TSAI Wu (Composite skins)

Displacement Constraints

Flutter Constraints

Design Variables153 design variablesUpper & lower surface linked for each plyorientation

uztip7.8 in.≤

V f 18270 in/sec≥

Material Properties Constraints/D.V.Flutter M =.8 seal level

Symmetric 9g pull-upM=0.8, 7.86 psi.

Flight Conditions

CRD

Kolonay 34

2 4 6 8 10 12

3680

3700

3720

3740

3760

3780

3800

3820

3840


Iteration

Wei

ght (

lbs)

Design History for ICW

Flutter only

Strength and Flutter

CRD

Kolonay 35

14000 16000 18000 20000-0.9

-0.8

-0.7

-0.6

-0.5

-0.4

-0.3

-0.2

-0.1

0

0.1

Mode 1Mode 2Mode 3Mode 4Mode 5Mode 6


Velocity (in/sec)

Dam

ping

Rat

ioICW Final Design V vs. Damping

Vf

CRD

Kolonay 36


14000 16000 18000 20000

0

20

40

60

80

100

120

140

160Mode 1Mode 2Mode 3Mode 4Mode 5Mode 6

Velocity (in/sec)

ICW Final Design Frequency vs. DampingF

requ

ency

(hz

)

CRD

Kolonay 37

-1.5 -1 -0.5 00

20

40

60

80

100

120

Mode 1Mode 2Mode 3Mode 4Mode 5Mode 6


Damping Ratio

Fre

quen

cy (

hz)

ICW Final Design Damping vs. Frequency

CRD

Kolonay 38

Trim Optimization• Number of FREE aerodynamic parameters > Number of trim DOF

• Allows redundant control surfaces

• Objective function based on trim parameters/trim DOF and calcu-lated responses (integrated maneuver loads, hinge moments etc.)

• Constraints based on trim parameters/trim DOF (integrated maneu-ver loads, hinge moments etc.)


CRD

Kolonay 39

Trim Optimization Problem• Problem is formulated as nonlinear mathematical programming problem

• With a vector of control effectors (control surfaces, thrust, user

defined controllers, smart structures)

• Design constraints and objectives are control effector limits, integratedmaneuver loads, and maneuver performance (e.g. roll rate)

• The procedure uses the redundant control effectors and trim parameters( etc.)to drive the trim state to a constrained minimum for the objec-tive and constraints defined

Minimize/(Maximize F– vs( )) the objective function

F vs( )

Subject to the constraint conditions

gj vs( ) 0≤ j 1 2…ncon,=

vsL

vs vsU

≤ ≤

vs

α β,


CRD

Kolonay 40

Trim Optimization• The basic trim equations (Equation 14) are used as constraints to enforce

equilibrium

• These two set of constraints state that the imbalance of forces andmoments at the support point must be less than a specified tolerance

• Other potential constraints

• ABS function - has singularity at 0

• Squared function - non-linear gradients

g1

…gnr

Lu2 Rδ–( )1

…1

tolerance–=

gnr

…g2 nr×

Rδ Lu2–( )1

…1

tolerance–=


CRD

Kolonay 41

Trim OptimizationForward Swept Wing Example [7]

• Minimize - (Nz + 100 x PRATE)•Subject to: Vehicle Imbalance - Lift < 1 lb - Pitch < 1 in-lb - Nz < 10 g’s - PRATE < 286 deg/sec

•RESULTS - TRIMMED SOLUTIONS

From Feasible Space - 30 Function Evals & 7 GradientsFrom Infeasible space - 182 Function Evals & 32 Gradients


Structure

Elevator

Aileron

CRD

Kolonay 42

Global Aeroelastic Design Software• MSC/NASTRAN (U.S.)

• UAI/ASTROS (recently bought by MSC) (U.S.)

• ELFINI (France, Dessault)

• LAGRANGE (Germany, formerly MBB)

• STARS (Great Britain, RAE)

• OPTSYS (Sweden, SAAB)

• COMPASS (China)

• ARGON (Russia, Central Aerohydrodynamic Institute)

Aeroelastic Optimization Software

43

nonlinear combinations)

ftware
RD
MSC/NASTRAN• General Modeling/Analysis Environment

- Multiple boundary conditions- Multiple disciplines per boundary condition- Selectable aerodynamic models- Optimization solvers (MMFD, SLP, SQP)

• Design variables- Element properties, shape- Design variable linking (physical, group, shape)

• Objective Functions- User definable based on available responses (linear/

• Static Aeroelastic Constraints•Stress•Strain•Displacement•Buckling (Panel, Euler column)

Aeroelastic Optimization So
C
Kolonay

44

trol surface effectiveness,

constraints

fective surfaces

lity in PATRAN environment

oftware
RD•Flexible Stability derivatives (lift effectiveness, conetc.)
•Free trim parameter constraints

• Trim Optimization- Balance Forces due to hinge moment and deflection

• Generic Control- Blends redundant control surfaces based on most ef

• Dynamic Aeroelastic Constraints- Flutter damping (P-K method)- Frequency constraints

• Pre-Post Processing- Extensive Flight Loads pre/post processing functiona

Aeroelastic Optimization S
C
Kolonay

45

pabilities



ftware
RD
UAI/ASTROS Aeroelastic Ca• General Modeling/Analysis Environment

- Multiple boundary conditions- Multiple disciplines per boundary condition- Selectable aerodynamic models- MPC’s set selectable

- Optimization solvers (FSD, MMFD( )

• Design variables- Element properties- Design variable linking (physical, group, shape)

• Objective Functions- User definable based on available responses (linear/

• Constraints- User definable based on available responses (linear/- Static Aeroelastic Constraints

•Stress•Strain

µDot

Aeroelastic Optimization So
C
Kolonay

46

trol surface effectiveness,

F and calculated responses

rated maneuver loads, hinge

d on available setdule converges

oftware
RD•Displacement•Buckling (Panel, Euler column)•Flexible Stability derivatives (lift effectiveness, conetc.)
•Aileron Effectiveness•Free trim parameter constraints•Integrated maneuver loads (BMST)

- Dynamic Aeroelastic Constraints•Flutter damping (P-K method)•Frequency constraints

• Trim Optimization- Formal mathematical programming formulation- Allows redundant control surfaces- Objective function based on trim parameters/trim DO

(integrated maneuver loads, hinge moments etc.)- Constraints based on trim parameters/trim DOF (integ

moments etc.).

• Nonlinear Trim- Rigid load vectors are interpolated/extrapolated base- Loop on trim solution until each control surface sche

Aeroelastic Optimization S
C
Kolonay

CRD

Kolonay 47

• Very easy to add user defined functionality and tailor the system

• Pre-Post Processing- Bulk data input 90% compatible with NASTRAN- Database accessible with SQL type interface and API


CRD

Kolonay 48

1. Neill, D.J., Herendeen, D.L., Venkayya, V.B., “ASTROS Enhancements, Vol III- ASTROSTheoretical Manual”, WL-TR-95-3006.

2. Neill, D. J., Johnson E. H., Herendeen K. L., “Automated structural Optimization System(ASTROS),” AFWAL-TR-883028 Volume II-User’s Manual, April 1988.

3. Hajela, P. “A Root Locus Based Flutter Synthesis Procedure,” AIAA Paper 83-0063, Jan.1983.

4. Grumman Aerospace Corporation, “An Automated Procedure for Flutter and Strength Analy-sis and Optimization of Aerospace Vehicles Volume I. Theory and Application,”, AFFDL-TR-75-137,.

5. Hassig, H.J., “An Approximate True Damping Solution of the Flutter Equation by Determi-nant Iteration,” Journal of Aircraft, Vol. 8, No. 11, November 1971, pp. 885-889.

6. Neill, D.J., “MSC/Flight Loads and Dynamics Training,”, The MacNeal-Schwendler Corpora-tion, 815 Colorado Boulevard, Los Angeles, CA, August 1999.

7. Love, M.L., Egle, D.D., “Aerodynamic Analysis for the Design Environment (AANDE), The-oretical and Applications Studies Document,” Lockheed Martin Tactical Aircraft Systems Codeident: 81755.

References

Motivation for Optimization• Missions of aeronautical and space vehicles are becoming increasingly complex• Identifying trade-offs among pertinent disciplines is critical in obtaining designs• Traditional methods may not achieve a design let alone an optimal design• Optimization also used to evaluate/design modifications to existing systems

IntroductionAircraft Design Considerations in MDA/MDO

Aeroelastic OptimizationThe Cultural and Convention CenterMETUInonu bulvariAnkara, TurkeySponsored by:RTA-NATOThe Applied Vehicle Technology Panelpresented byR.M. Kolonay Ph.D.General Electric Corporate Research & Development CenterAnkara, Turkey Oct.. 1-5, 2001• Introduction• Aeroelastic Optimization- Linear Static Aeroelastic Optimization- Linear Dynamic Aeroelastic Optimization

• Trim Optimization• Commercial Programs with Aeroelastic Design Capabilities• Appendix B - Static and Static Aeroelastic Gradients

Presentation OutlineIntroductionGoal of Aeroelastic Optimization• Determine the aerodynamic and structural parameters to satisfy all necessary requirements over ...- Traditionally, weight and performance were main objective functions. That has changed• Life cycle cost, manufacturability, maintainability, etc. now equal players- Historically, aerodynamic parameters (sweep, planform, etc.) where considered in conceptual design- Structural parameters considered in preliminary design- Recent MDO algorithms combining conceptual, preliminary and detailed design variables.- With advent of AAW technology/active control(piezoelectrics) must also consider some control de...- Recently nonlinear engineering analysis considered (CFD, nonlinear FEM)

IntroductionScope of Discussion- Preliminary Design• Assume external geometry fixed• Determine structural physical properties (such as membrane/shell thicknesses, composite lay-ups...• Mathematical statement(28)- Objective function (weight, lift effectiveness, or any linear/nonlinear combination of response...- Behavioral constraints (stress, displacement, aeroelastic response, flutter etc.) (can be as ma...- Allowable value for- vector of design variables (assumed continuous, 1000 max)- Typically implicit functions ofNote: Just because considered engineering analyses are linear does not imply that the responses a...

A Solution ApproachEfficient solution to (28), the classical nonlinear mathematical programming problem, can be achi...• Approximation concepts• Design variable linking• Active constraint strategies• Move limit strategies

Approximation concepts• Single point or multi-point first order (requires only gradients) approximations- 1st order Taylor Series direct space- 1st order Taylor Series inverse space

• Second order approximations require Hessian matrix (difficult to evaluate). Two point approxima...

Aeroelastic OptimizationDesign Variable Linking(29)• Unique linking - Single value in any given row or column of• Group linking - Only one entry per row but may have multiple entries in a given column• Shape function linking - Multiple entries in a row and or column

Aeroelastic OptimizationActive constraint strategies• Pass an “active” subset of the constraints to the approximate problem- Retain all violated constraints- Retain constraints within 10% of the boundary- Don’t retain more than 1 or 2 times NDV unless necessary

• Update the “active” set for each new approximate problem• Calculate gradients for only the “active” set of constraints- Results in large computational savings

Aeroelastic OptimizationEffective solutions to (28) should require less than 30 detailed Engineering Analyses (including ...

Aeroelastic OptimizationAeroelastic OptimizationAeroelastic OptimizationGradient Calculations• Efficient accurate gradient calculations are essential to gradient based solutions to (28).• If at all possible avoid finite difference gradients- Costly, and prone to step size problems

• Use analytic or semi-analytic gradients

Aeroelastic OptimizationAeroelastic OptimizationMove Limit Strategies• Using approximations for constraints functions, objective function, constraint function gradien...• movlim is problem dependent, values typically can range anywhere from 1.1 to 2.0

Aeroelastic OptimizationVon Mises Stress/Tsai-Hill Constraint• - Element normal, transverse, and shear strains• - Normal, transverse and shear allowables.- - each may be compression or tension allowables depending on the sign of- need not be equal

Static Aeroelastic OptimizationGradient Calculations• For the current scope, static and dynamic aeroelastic gradients depend on the gradients of at t...• Decompose the elemental matrices into 3 parts- Invariant w.r.t. design variable- Linear variation w.r.t.- Non-linear variation w.r.t.

(30)A - the assemble operation for the elemental matrices to global- superscript indicating elemental matrices- being the terms of the design variable linking matrix in (29)Differentiating (30) w.r.t. yields (A is an assembly operator)

(31)With by forward finite difference as

(32)fully analytic, semi-analytic

Aeroelastic OptimizationAeroelastic OptimizationAeroelastic OptimizationAeroelastic Constraints Considered• Static Aeroelastic Constraints- Stress- Strain- Displacement- Flexible stability derivatives (lift effectiveness, control surface effectiveness, etc.)- Aileron effectiveness- Free trim parameter constraints

• Dynamic Aeroelastic Constraints- Flutter

Aeroelastic OptimizationRequirements for Optimization Environment• Multiple Boundary Conditions considered simultaneously- Symmetric- Anti-symmetric- Asymmetric- Store configurations

• Multiple disciplines considered simultaneously- Statics- Dynamics- Static Aeroelasticity- Dynamic Aeroelasticity

• Ability to construct constraints and objective functions from available responses

Aeroelastic OptimizationPrincipal Strain Constraintwith• Fiber and transverse strain constraints often used as well

Static Aeroelastic OptimizationDisplacement Constraints• - Weighting factors on and user specified limit respectively• Enables specifying limits of the shape of the displacements- Wing tip twist constraint-

Static Aeroelastic OptimizationAileron Effectiveness ConstraintWith- Rolling moment about the aircraft centerline- Aileron deflection- Roll rate nondimensionalized by wing span and aircraft velocity- Flexibility effects are included in the derivatives• Steady roll rate achievable for a unit value of aileron deflection.

Static Aeroelastic OptimizationFlexible Stability Derivative Constraint• Enables constraint of any flexible derivative in any axis for any trim parameter• For example, lift effectiveness

Static AeroelasticityTrim Parameter Constraint• Any FREE parameter in the trim solution can be constrained• Angle of attack, control surface deflection etc.

Static Aeroelastic OptimizationFrequency Constraints• Constraint actually on the eigenvalue (improves accuracy of approximation)

Dynamic Aeroelastic OptimizationFlutter Constraint• Constraint is formulated in terms of satisfying requirements on the modal damping values at a s...• Advantages of constraining damping- No need to calculate flutter velocity- Able to capture “hump” modes

• Disadvantage- modal damping is only estimated away from the axis for P-K solution

Dynamic AeroelasticityVelocityRectangular Wing ExampleOriginalDesired

Static AeroelasticityRectangular Wing Example• Flight Conditions- Symmetric- Anti-symmetric

• Constraints- Maximum Tip Rotation (Degs)- 1.0- Maximum Lift Effectiveness - 1.60- Minimum Aileron Effectiveness.30-

Aeroelastic Optimization SoftwareStatic Aeroelastic OptimizationE = 10.E06 psiPoisson’s Ratio =.3Weight Density 0.1 lb/in3Tensile Strength = 20.0 ksiCompressive Strength 15 ksiShear Strength 12.0 ksi• Design Variables- Inboard top skins- Inboard bottom skins- Outboard top skins- Outboard bottom skins

• Objective Function- Weight

Rectangular Wing Example• Four Design Cases Run

Static Aeroelastic OptimizationRectangular Wing Example• Design Run Results

Static Aeroelastic OptimizationIntermediate Complexity Wing (ICW) Example

Aeroelastic OptimizationOrthotropic MaterialE1 = 19.9E6 psiE2 = 1.5E6 psiG12 = 0.85E6 psilb/in3Ply = 0.04 in.Isotropic MaterialE = 10.5E6 psilb/in3= 0.04 in.

Aeroelastic OptimizationStress Constraints110 Von Mises Stress (rods&shear panels)256 TSAI Wu (Composite skins)Displacement ConstraintsFlutter ConstraintsDesign Variables153 design variablesUpper & lower surface linked for each ply orientationFlutter M =.8 seal levelSymmetric 9g pull-upM=0.8, 7.86 psi.

Aeroelastic OptimizationAeroelastic OptimizationAeroelastic OptimizationAeroelastic OptimizationTrim Optimization• Number of FREE aerodynamic parameters > Number of trim DOF• Allows redundant control surfaces• Objective function based on trim parameters/trim DOF and calculated responses (integrated maneu...• Constraints based on trim parameters/trim DOF (integrated maneuver loads, hinge moments etc.)

Aeroelastic OptimizationTrim Optimization Problem• Problem is formulated as nonlinear mathematical programming problem• With a vector of control effectors (control surfaces, thrust, user defined controllers, smart s...• Design constraints and objectives are control effector limits, integrated maneuver loads, and m...• The procedure uses the redundant control effectors and trim parameters ( etc.)to drive the trim...

Aeroelastic OptimizationTrim Optimization• The basic trim equations (Equation 14) are used as constraints to enforce equilibrium• These two set of constraints state that the imbalance of forces and moments at the support poin...• Other potential constraints• ABS function - has singularity at 0• Squared function - non-linear gradients

Aeroelastic OptimizationGlobal Aeroelastic Design Software• MSC/NASTRAN (U.S.)• UAI/ASTROS (recently bought by MSC) (U.S.)• ELFINI (France, Dessault)• LAGRANGE (Germany, formerly MBB)• STARS (Great Britain, RAE)• OPTSYS (Sweden, SAAB)• COMPASS (China)• ARGON (Russia, Central Aerohydrodynamic Institute)

Aeroelastic Optimization SoftwareMSC/NASTRAN• General Modeling/Analysis Environment- Multiple boundary conditions- Multiple disciplines per boundary condition- Selectable aerodynamic models- Optimization solvers (MMFD, SLP, SQP)

• Design variables- Element properties, shape- Design variable linking (physical, group, shape)

• Objective Functions- User definable based on available responses (linear/nonlinear combinations)

• Static Aeroelastic Constraints• Stress• Strain• Displacement• Buckling (Panel, Euler column)• Flexible Stability derivatives (lift effectiveness, control surface effectiveness, etc.)• Free trim parameter constraints

• Trim Optimization- Balance Forces due to hinge moment and deflection constraints

• Generic Control- Blends redundant control surfaces based on most effective surfaces

• Dynamic Aeroelastic Constraints- Flutter damping (P-K method)- Frequency constraints

• Pre-Post Processing- Extensive Flight Loads pre/post processing functionality in PATRAN environment

Aeroelastic Optimization SoftwareAeroelastic Optimization SoftwareTrim OptimizationForward Swept Wing Example [7]• Minimize - (Nz + 100 x PRATE)• Subject to: Vehicle Imbalance- Lift < 1 lb- Pitch < 1 in-lb- Nz < 10 g’s- PRATE < 286 deg/sec• RESULTS - TRIMMED SOLUTIONSFrom Feasible Space - 30 Function Evals & 7 GradientsFrom Infeasible space - 182 Function Evals & 32 Gradients

Aeroelastic OptimizationUAI/ASTROS Aeroelastic Capabilities• General Modeling/Analysis Environment- Multiple boundary conditions- Multiple disciplines per boundary condition- Selectable aerodynamic models- MPC’s set selectable- Optimization solvers (FSD, MMFD()

• Design variables- Element properties- Design variable linking (physical, group, shape)

• Objective Functions- User definable based on available responses (linear/nonlinear combinations)

• Constraints- User definable based on available responses (linear/nonlinear combinations)- Static Aeroelastic Constraints• Stress• Strain• Displacement• Buckling (Panel, Euler column)• Flexible Stability derivatives (lift effectiveness, control surface effectiveness, etc.)• Aileron Effectiveness• Free trim parameter constraints• Integrated maneuver loads (BMST)- Dynamic Aeroelastic Constraints• Flutter damping (P-K method)• Frequency constraints

• Trim Optimization- Formal mathematical programming formulation- Allows redundant control surfaces- Objective function based on trim parameters/trim DOF and calculated responses (integrated maneu...- Constraints based on trim parameters/trim DOF (integrated maneuver loads, hinge moments etc.).

• Nonlinear Trim- Rigid load vectors are interpolated/extrapolated based on available set- Loop on trim solution until each control surface schedule converges1. Neill, D.J., Herendeen, D.L., Venkayya, V.B., “ASTROS Enhancements, Vol III- ASTROS Theoretica...2. Neill, D. J., Johnson E. H., Herendeen K. L., “Automated structural Optimization System (ASTRO...3. Hajela, P. “A Root Locus Based Flutter Synthesis Procedure,” AIAA Paper 83-0063, Jan. 1983.4. Grumman Aerospace Corporation, “An Automated Procedure for Flutter and Strength Analysis and O...5. Hassig, H.J., “An Approximate True Damping Solution of the Flutter Equation by Determinant Ite...6. Neill, D.J., “MSC/Flight Loads and Dynamics Training,”, The MacNeal-Schwendler Corporation, 81...7. Love, M.L., Egle, D.D., “Aerodynamic Analysis for the Design Environment (AANDE), Theoretical ...

ReferencesAeroelastic Optimization Software• Very easy to add user defined functionality and tailor the system• Pre-Post Processing- Bulk data input 90% compatible with NASTRAN- Database accessible with SQL type interface and API


Date post:	10-Feb-2021
Category:	Documents
Upload:	others
View:	4 times
Download:	0 times

CRD Aeroelastic Optimization - METUyyaman/avt086/Kolonay/Ray_Kolonay_3.pdfCRD Kolonay 5 Goal of...

Documents