Rotary actuators
DA-H – series
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com Copyright © 2006 by HKSWe reserve the right to make modifications
Technical informations DA-H 40Hydraulic rotary actuator
TI D
A-H
40
- 06
06 E
Fig. 1
Technical data Type DA-H 40
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 0,96Max. working pressure * bar 210Max. radial load N 1567Max. axial load N 8 000Absorption volume Angle 90° dm3 0,020
Angle 180° dm3 0,040Angle 270° dm3 0,060Angle 360° dm3 0,080
Weight Angle 90° kg approx 4,3Angle 180° kg approx 4,8Angle 270° kg approx 5,8Angle 360° kg approx 6,2
Max. nominal torque at 210 bars Nm 200Max. nominal torque at 210 barswith camshaft Nm 160
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Copyright © 2006 by HKSWe reserve the right to make modifications
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com Copyright © 2006 by HKS
Dimension table
Typ DA-H 40A k 6 22DIN 5480*) W 22x1,25x16x8fB Ø 98C f 7 Ø 55D 43E Ø 65F Ø 75G 2,5H DIN 6885 45I DIN 6885 8J DIN 6885 14K 84L 50M 3N 4O 16P 90° 124
180° 149270° 182360° 210
Q 39R 90° 28
180° 41270° 55360° 68,5
S 45° G 1/8"T 60°U Number 5U 9
Special version HW-hollow shaft toDIN 5480 on requestB 26Spline profile DIN 5463 6x11x14
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 45J1 7,8CH7 Ø 12I1P9 4
*) Special version KW spline shaftDIN is not shown
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
Special version with camshaftW f7 16W1 h6 10Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 142
180° 167270° 200360° 228
Technical informations DA-H 40Hydraulic rotary actuator
We reserve the right to make modifications
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculationof the shaft for torsional strength isstrongly recommended.
Fig. 1
Technical data Type DA-H 50
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 1,62Max. working pressure * bar 210Max. radial load N 2976Max. axial load N 10000Absorption volume Angle 90° dm3 0,028
Angle 180° dm3 0,056Angle 270° dm3 0,084Angle 360° dm3 0,113
Weight Angle 90° kg ca. 6Angle 180° kg ca. 6,8Angle 270° kg ca. 7,8Angle 360° kg ca. 8,7
Max. nominal torque at 210 bars Nm 340Max. nominal torque at 210 barswith camshaft Nm 290
TI D
A-H
50
- 06
06 E
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 50Hydraulic rotary actuator
Copyright © 2006 by HKSWe reserve the right to make modifications
Dimension table
Typ DA-H 50A k 6 28DIN 5480*) W 28x2x12x8fB Ø 110C f 7 Ø 68D 49E Ø 72F Ø 82G 2H DIN 6885 56I DIN 6885 8J DIN 6885 17K 90L 60M 3N 4O 18P 90° 133
180° 164270° 200360° 232
Q 39R 90° 31
180° 48270° 65360° 80,5
S 45° G 1/8"T 60°U Number 5U 9
Special version HW-hollow shaft toDIN 5480 on requestB 30Spline profile DIN 5463 6x16x20
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 55J1 10,1C
H7Ø 16
I1P9
5
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 18W1 h6 10Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 149
180° 182270° 218360° 250
Technical informations DA-H 50Hydraulic rotary actuator
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com Copyright © 2006 by HKS
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
We reserve the right to make modifications
TI D
A-H
63
- 06
06 E
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 63Hydraulic rotary actuator
Copyright © 2006 by HKSWe reserve the right to make modifications
Fig. 1
Technical data Type DA-H 63
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 3,10Max. working pressure * bar 210Max. radial load N 4364Max. axial load N 14000Absorption volume Angle 90° dm3 0,058
Angle 180° dm3 0,117Angle 270° dm3 0,176Angle 360° dm3 0,235
Weight Angle 90° kg ca. 8,5Angle 180° kg ca. 9,8Angle 270° kg ca. 12,9Angle 360° kg ca. 14
Max. nominal torque at 210 bars Nm 650Max. nominal torque at 210 barswith camshaft Nm 540
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com Copyright © 2006 by HKSWe reserve the right to make modifications
Dimension table
Typ DA-H 63A k 6 35DIN 5480*) W 35x2x16x8fB Ø 128C f 7 Ø 80D 57E Ø 87F Ø 95G 5H DIN 6885 70I DIN 6885 10J DIN 6885 20,5K 108L 80M 3,5N 5O 25P 90° 152
180° 200270° 245360° 284
Q 48R 90° 37
180° 57270° 79360° 99
S 45° G 1/4"T 60°U Number 5U 11
Special version HW-hollow shaft toDIN 5480 on requestB 35Spline profile DIN 5463 6x21x25
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 65J1 14,1C
H7Ø 24
I1P9
8
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 18W1 h6 10Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 172
180° 220270° 264,5360° 304,5
Technical informations DA-H 63Hydraulic rotary actuator
TI D
A-H
80
- 12
08 E
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 80Hydraulic rotary actuator
Copyright © 2008 by HKSWe reserve the right to make modifications
Fig. 1
Technical data Type DA-H 80
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 6,20Max. working pressure * bar 210Max. radial load N 7875Max. axial load N 19050Absorption volume Angle 90° dm3 0,131
Angle 180° dm3 0,262Angle 270° dm3 0,391Angle 360° dm3 0,521
Weight Angle 90° kg ca. 16,7Angle 180° kg ca. 19,1Angle 270° kg ca. 21,5Angle 360° kg ca. 24
Max. nominal torque at 210 bars Nm 1300Max. nominal torque at 210 barswith camshaft Nm 1170
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
Technical informations DA-H 80Hydraulic rotary actuator
We reserve the right to make modifications
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com Copyright © 2008 by HKS
Dimension table
Typ DA-H 80A k 6 42DIN 5480*) W 40x2x18x8fB Ø 150C f 7 Ø 100D 66E Ø 108F Ø 118G 5H DIN 6885 100I DIN 6885 12J DIN 6885 24K 130L 110M 3N 6O 30P 90° 187
180° 240270° 290360° 345
Q 57R 90° 37
180° 74270° 101360° 125
S 45° G 3/8"T 45°U Number 7U 11
Special version HW-hollow shaft toDIN 5480 on requestB 40Spline profile DIN 5463 6x26x32
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 90J1 18,3CH7 Ø 30I1P9 8
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 25W1 h6 16Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 212
180° 262270° 314,5360° 367,5
TI D
A-H
100
-
1208
E
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 100Hydraulic rotary actuator
Copyright © 2008 by HKSWe reserve the right to make modifications
Fig. 1
Technical data Type DA-H 100
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 11,90Max. working pressure * bar 210Max. radial load N 11250Max. axial load N 24900Absorption volume Angle 90° dm3 0,255
Angle 180° dm3 0,509Angle 270° dm3 0,763Angle 360° dm3 1,018
Weight Angle 90° kg ca.24,1Angle 180° kg ca.29,2Angle 270° kg ca.34Angle 360° kg ca.38,5
Max. nominal torque at 210 bars Nm 2500Max. nominal torque at 210 barswith camshaft Nm 2340
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
We reserve the right to make modifications
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com Copyright © 2008 by HKS
Dimension table
Typ DA-H 100A m 6 55DIN 5480*) W 55x2x26x8fB Ø 178C f 7 Ø 115D 80E Ø 130F Ø 147G 5H DIN 6885 100I DIN 6885 16J DIN 6885 31,5K 155L 110M 4N 6O 31P 90° 241
180° 311270° 366360° 432
Q 65R 90° 56,5
180° 89270° 121,5360° 154
S 45° G 1/2"T 45°U Number 7U 14
Special version HW-hollow shaft toDIN 5480 on requestB 50Spline profile DIN 5463 8x36x42
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 105J1 24,3CH7 Ø 42I1P9 12
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 25W1 h6 16Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 245
180° 311270° 381360° 442
Technical informations DA-H 100Hydraulic rotary actuator
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 125Hydraulic rotary actuator
Fig. 1
TI D
A-H
125
- 1
208
D
Copyright © 2008 by HKSWe reserve the right to make modifications
Technical data Type DA-H 125
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 24,32Max. working pressure * bar 210Max. radial load N 17552Max. axial load N 34100Absorption volume Angle 90° dm3 0,518
Angle 180° dm3 1,036Angle 270° dm3 1,554Angle 360° dm3 2,071
Weight Angle 90° kg ca. 47Angle 180° kg ca. 55Angle 270° kg ca. 63,5Angle 360° kg ca. 72,5
Max. nominal torque at 210 bars Nm 5107Max. nominal torque at 210 barswith camshaft Nm 4900
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
We reserve the right to make modifications
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com Copyright © 2008 by HKS
Technical informations DA-H 125Hydraulic rotary actuator
Dimension table
Typ DA-H 125A m 6 70DIN 5480*) W 70x2x34x8fB Ø 222C f 7 Ø 150D 94E Ø 167F Ø 183G 7H DIN 6885 125I DIN 6885 20J DIN 6885 39,5K 195L 140M 4N 8O 37P 90° 271,5
180° 392270° 480360° 532,5
Q 74R 90° 76,2
180° 118,5270° 162,5360° 207
S 45° G 1/2"T 40°U Number 8U 18
Special version HW-hollow shaft toDIN 5480 on requestB 62Spline profile DIN 5463 8x46x54
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 120J1 31,8CH7 Ø 55I1P9 16
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 25W1 h6 16Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 298
180° 392270° 482360° 557
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 140Hydraulic rotary actuator
Fig. 1
TI D
A-H
140
- 1
208
E
Copyright © 2008 by HKSWe reserve the right to make modifications
Technical data Type DA-H 140
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 33,80Max. working pressure * bar 210Max. radial load N 17800Max. axial load N 34800Absorption volume Angle 90° dm3 0,759
Angle 180° dm3 1,518Angle 270° dm3 2,277Angle 360° dm3 3,036
Weight Angle 90° kg ca. 74Angle 180° kg ca. 87Angle 270° kg ca. 101Angle 360° kg ca. 115
Max. nominal torque at 210 bars Nm 7100Max. nominal torque at 210 barswith camshaft Nm 6870
We reserve the right to make modifications
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com Copyright © 2006 by HKS
Technical informations DA-H 140Hydraulic rotary actuator
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
Dimension table
Typ DA-H 140A m 6 80DIN 5480*) W 80x3x25x8fB Ø 250C f 7 Ø 160D 105E Ø 187F Ø 210G 5H DIN 6885 140I DIN 6885 22J DIN 6885 45K 220L 150M 7N 10O 40P 90° 304
180° 401270° 499360° 597
Q 78R 90° 82
180° 130270° 180360° 229
S 45° G 1/2"T 40°U Number 8U 18
Special version HW-hollow shaft toDIN 5480 on requestB 62Spline profile DIN 5463 8x52x60
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 120J1 34,4CH7 Ø 60I1P9 18
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 25W1 h6 16Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 334,5
180° 431270° 529360° 627
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 160Hydraulic rotary actuator
TI D
A-H
160
-
1208
E
Copyright © 2008 by HKSWe reserve the right to make modifications
Fig. 1
Technical data Type DA-H 160
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 53,80Max. working pressure * bar 210Max. radial load N 36300Max. axial load N 46200Absorption volume Angle 90° dm3 1,145
Angle 180° dm3 2,290Angle 270° dm3 3,435Angle 360° dm3 4,580
Weight Angle 90° kg ca. 114Angle 180° kg ca. 136Angle 270° kg ca. 154Angle 360° kg ca. 170
Max. nominal torque at 210 bars Nm 11300Max. nominal torque at 210 barswith camshaft Nm 10590
We reserve the right to make modifications
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com Copyright © 2008 by HKS
Technical informations DA-H 160Hydraulic rotary actuator
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
Dimension table
Typ DA-H 160A m 6 100DIN 5480*) W 100x3x32x8fB Ø 278C f 7 Ø 190D 127E Ø 206F Ø 240G 5H DIN 6885 200I DIN 6885 28J DIN 6885 56K 245L 210M 5N 12O 43P 90° 364
180° 473,5270° 592,5360° 707,5
Q 94R 90° 110
180° 168270° 224360° 281
S 45° G 3/4"T 40°U Number 8U 22
Special version HW-hollow shaft toDIN 5480 on requestB 82Spline profile DIN 5463 8x62x72
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 150J1 42,4CH7 Ø 75I1P9 20
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 40W1 h6 25Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 394,5
180° 502,5270° 621,5360° 733,5
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 180Hydraulic rotary actuator
TI D
A-H
180
- 1
208
E
Copyright © 2008 by HKSWe reserve the right to make modifications
Fig. 1
Technical data Type DA-H 180
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 77,14Max. working pressure * bar 210Max. radial load N 37600Max. axial load N 47400Absorption volume Angle 90° dm3 1,678
Angle 180° dm3 3,356Angle 270° dm3 5,034Angle 360° dm3 6,712
Weight Angle 90° kg ca. 150Angle 180° kg ca. 187Angle 270° kg ca. 213Angle 360° kg ca. 245
Max. nominal torque at 210 bars Nm 16200Max. nominal torque at 210 barswith camshaft Nm 15680
We reserve the right to make modifications Copyright © 2008 by HKS
Technical informations DA-H 180Hydraulic rotary actuator
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com
Dimension table
Typ DA-H 180A m 6 105DIN 5480*) W 105x3x34x8fB Ø 298C f 7 Ø 210D 138E Ø 226F Ø 270G 5H DIN 6885 200I DIN 6885 28J DIN 6885 58,5K 265L 210M 5N 12O 47P 90° 435
180° 565270° 702360° 880
Q 127R 90° 114
180° 186270° 253360° 321
S 45° G 1"T 40°U Number 11U 22
Special version HW-hollow shaft toDIN 5480 on requestB 100Spline profile DIN 5463 10x72x82
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 150J1 42,4CH7 Ø 75I1P9 20
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 32W1 h6 25Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 475
180° 595270° 742360° 900
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 200Hydraulic rotary actuator
TI D
A-H
200
- 1
208
E
Copyright © 2008 by HKSWe reserve the right to make modifications
Fig. 1
Technical data Type DA-H 200
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 106,20Max. working pressure * bar 210Max. radial load N 67210Max. axial load N 62000Absorption volume Angle 90° dm3 2,261
Angle 180° dm3 4,522Angle 270° dm3 6,783Angle 360° dm3 9,044
Weight Angle 90° kg ca. 194Angle 180° kg ca. 238Angle 270° kg ca. 264Angle 360° kg ca. 306
Max. nominal torque at 210 bars Nm 22300Max. nominal torque at 210 barswith camshaft Nm 21400
We reserve the right to make modifications Copyright © 2008 by HKS
Technical informations DA-H 200Hydraulic rotary actuator
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com
Dimension table
Typ DA-H 200A m 6 120DIN 5480*) W 120x5x22x8fB Ø 325C f 7 Ø 235D 150E Ø 255F Ø 295G 5H DIN 6885 200I DIN 6885 32J DIN 6885 67K 290L 210M 4N 10O 54P 90° 438,5
180° 584,5270° 725,5360° 876,5
Q 125R 90° 125
180° 196270° 265,5360° 340
S 45° G 1"T 30°U Number 11U 22
Special version HW-hollow shaft toDIN 5480 on requestB 100Spline profile DIN 5463 10x82x92
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 175J1 52,9CH7 Ø 95I1P9 25
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 40W1 h6 25Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 478,5
180° 632,5270° 765,5360° 914,5
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 225Hydraulic rotary actuator
TI D
A-H
225
- 1
208
E
Copyright © 2008 by HKSWe reserve the right to make modifications
Fig. 1
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 152,38Max. working pressure * bar 210Max. radial load N 69000Max. axial load N 63100Absorption volume Angle 90° dm3 3,388
Angle 180° dm3 6,676Angle 270° dm3 10,014Angle 360° dm3 13,352
Weight Winkel 90° kg ca. 404Angle 180° kg ca. 488Angle 270° kg ca. 565Angle 360° kg ca. 630
Max. nominal torque at 210 bars Nm 32000Max. nominal torque at 210 bars
Technical data Type DA-H 225
with camshaft Nm 30980
We reserve the right to make modifications Copyright © 2008 by HKS
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com
Dimension table
Typ DA-H 225A m 6 140DIN 5480*) W 120x5x26x8fB Ø 385C f 7 Ø 260D 224E Ø 300F Ø 350G 5H DIN 6885 250I DIN 6885 36J DIN 6885 78K 345L 260M 6N 15O 64P 90° 570
180° 732270° 900360° 1069
Q 155R 90° 159
180° 240270° 321360° 403
S 45° G 1"T 22,5°U Number 15U 22
Special version HW-hollow shaft toDIN 5480 on requestB 120Spline profile DIN 5463 10x92x102
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 175J1 56,4CH7 Ø 100I1P9 28
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 40W1 h6 25Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 645
180° 807270° 975360° 1140
Technical informations DA-H 225Hydraulic rotary actuator
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 225 SHydraulic rotary actuator
TI D
A-H
225
S -
1208
E
Copyright © 2008 by HKSWe reserve the right to make modifications
Fig. 1
Technical data Type DA-H 225 S
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 185,33Max. working pressure * bar 210Max. radial load N 69000Max. axial load N 63100Absorption volume Angle 90° dm3 4,127
Angle 180° dm3 8,245Angle 270° dm3 12,368Angle 360° dm3 16,491
Weight Angle 90° kg ca. 487Angle 180° kg ca. 543Angle 270° kg ca. 637Angle 360° kg ca. 684
Max. nominal torque at 210 bars Nm 38920Max. nominal torque at 210 barswith camshaft Nm 37690
Dimension table
Typ DA-H 225 SA m 6 140DIN 5480*) W 140x5x26x8fB Ø 385C f 7 Ø 260D 224E Ø 300F Ø 350G 5H DIN 6885 250I DIN 6885 36J DIN 6885 78K 345L 260M 6N 15O 64P 90° 690
180° 805270° 995360° 1220
Q 155R 90° 175
180° 276270° 381360° 484
S 45° G 1"T 22,5°U Number 15U 22
Special version HW-hollow shaft toDIN 5480 on requestB 120Spline profile DIN 5463 10x92x102
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 175J1 56,4CH7 Ø 100I1P9 28
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 40W1 h6 25Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 765
180° 880270° 1070360° 1295
We reserve the right to make modifications Copyright © 2008 by HKS
Technical informations DA-H 225 SHydraulic rotary actuator
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 250Hydraulic rotary actuator
TI D
A-H
250
- 1
208
E
Copyright © 2008 by HKSWe reserve the right to make modifications
Fig. 1
Technical data Type DA-H 250
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 209,52Max. working pressure * bar 210Max. radial load N 78000Max. axial load N 66500Absorption volume Angle 90° dm3 4,607
Angle 180° dm3 9,214Angle 270° dm3 13,821Angle 360° dm3 18,429
Weight Angle 90° kg ca. 630Angle 180° kg ca. 726Angle 270° kg ca. 815Angle 360° kg ca. 912
Max. nominal torque at 210 bars Nm 44000Max. nominal torque at 210 barswith camshaft Nm 42870
We reserve the right to make modifications Copyright © 2008 by HKS
Technical informations DA-H 250Hydraulic rotary actuator
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com
Dimension table
Typ DA-H 250A m 6 150DIN 5480*) W 150x5x28x8fB Ø 450C f 7 Ø 300D 240E Ø 346F Ø 385G 10H DIN 6885 280I DIN 6885 36J DIN 6885 83K 400L 300M 6N 20O 90P 90° 710
180° 875270° 1060360° 1261
Q 224R 90° 155
180° 248270° 343360° 437
S 45° G 1"T 22,5°U Number 15U 26
Special version HW-hollow shaft toDIN 5480 on requestB 120Spline profile DIN 5463 10x102x112
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 175J1 61,4CH7 Ø 110I1P9 28
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 40W1 h6 25Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 725
180° 910270° 1095360° 1286
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 280Hydraulic rotary actuator
TI D
A-H
280
- 1
208
E
Copyright © 2008 by HKSWe reserve the right to make modifications
Fig. 1
Technical data Type DA-H 280
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 289,52Max. working pressure * bar 210Max. radial load N 84600Max. axial load N 71000Absorption volume Angle 90° dm3 6,348
Angle 180° dm3 12,695Angle 270° dm3 19,043Angle 360° dm3 25,391
Weight Angle 90° kg ca. 874Angle 180° kg ca. 1011Angle 270° kg ca. 1164Angle 360° kg ca. 1292
Max. nominal torque at 210 bars Nm 60800Max. nominal torque at 210 barswith camshaft Nm 59580
We reserve the right to make modifications Copyright © 2008 by HKS
Technical informations DA-H 280Hydraulic rotary actuator
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com
Dimension table
Typ DA-H 280A m 6 170DIN 5480*) W 170x5x32x8fB Ø 490C f 7 Ø 340D 266E Ø 394F Ø 435G 10H DIN 6885 280I DIN 6885 40J DIN 6885 94K 450L 300M 6N 20O 100P 90° 790
180° 1000270° 1205360° 1408
Q 261R 90° 183
180° 287270° 392360° 493
S 45° G 1"T 18°U Number 19U 26
Special version HW-hollow shaft toDIN 5480 on requestB 130Spline profile DIN 5463 10x112x125
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 200J1 67,4CH7 Ø 120I1P9 32
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 40W1 h6 25Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 865
180° 1075270° 1280360° 1483
General characteristicsRotary actuators in the DA-H series are characterisedby their performance range. At a working pressure ofup to 210 bars, torques of up to 250,000 Nm arepossible (higher working pressures on request).Another characteristic is the extremely low angularclearance.
HKS rotary actuators in the DA-H series offer thefollowing standards:
- 20 sizes from 36 to 250000 Nm with pistonsØ 40– Ø 450 mm
- 4 rotary angle rages for each size: 90°, 180°,270° and 360°
- Actuator shaft with 2 feather keys or DIN5480 involute spline
- Tandem seal on the actuator shaftBecause of the almost infinite design possibilities forthe front face almost all connection variants can beachieved with these actuators.
Auxiliary equipment- Cushioning at both ends- Rotary angle adjustment up to + 4°- Camshaft- Hollow shaft with DIN 5463, DIN 5480 or
DIN 6885 profile
Special versions- Actuator shaft with spline profile to DIN
5463- Actuator shaft with second drive cog- Actuator shaft and mounting flange
designed to customer’s requirements- Rotary angle adjustment throughout the
range of rotation- Limit switch equipment- Direct valve connection, 3 mounting
positions- All intermediate rotation angles can be
supplied- Range of rotation exceeding 360°- Sea-water resistant- Additional bearing for high radial forces- Change of direction of rotation- Further special versions are available
Typical applications
HKS rotary actuators have proved their worththroughout the industrial sector. For example, theyare used in construction machinery, machine tools,bending machines, foundry, mining, agricultural andpacking machines, transfer lines, manipulators,armatures, as well as in shipbuilding, motor vehicles,assembly platforms and in ventilation engineering.HKS rotary actuators are reliable and require nomaintenance. This is demonstrated, for example, 2300mm below sea-level, whey they are used as actuatorsfor armatures.
Functional description
The oil pressure supplied through connections P1 and P2 causes actuatorshaft G to perform a rotary movement. The linear movement of piston K ishere converted to a rotary movement by multiple helical gears in the housing,piston and shaft.
Direction of rotation
With the pressure at P1 actuator shaft G1 rotates from the initial position tothe left (anticlockwise).A change in direction of rotation is possible in a special version.
Normal position of the feather key:
Figure 1 shows the factory set position of piston K Changes of position arepossible.
Angle of rotation and its adjustment
In the standard version the angle of rotation may be up to 4° in the positiverange. An exact angle of rotation is achieved by means of an additional deviceWV.
Cushioning
The speed of rotation of actuator shaft G can be regulated in the limitpositions by throttle check valves. Further information on the subject ofcushioning may be requested on an additional page.
Technical informations DA-H 300Hydraulic rotary actuator
TI D
A-H
300
- 1
208
E
Copyright © 2008 by HKSWe reserve the right to make modifications
Fig. 1
Technical data Type DA-H 300
*) Working pressures > 210 bar on request
Nominal torque Nm/bar 361,9Max. working pressure * bar 210Max. radial load N 89400Max. axial load N 76000Absorption volume Angle 90° dm3 7,930
Angle 180° dm3 15,862Angle 270° dm3 23,790Angle 360° dm3 31,724
Weight Angle 90° kg ca. 1126Angle 180° kg ca. 1308Angle 270° kg ca. 1489Angle 360° kg ca. 1677
Max. nominal torque at 210 bars Nm 76000Max. nominal torque at 210 barswith camshaft Nm 74630
We reserve the right to make modifications Copyright © 2008 by HKS
Technical informations DA-H 300Hydraulic rotary actuator
Standard version with feather key
Special version with female thread
Special version hollow shaft with feather key grooves (DIN 6885)
Special version camshaft with cog
Special version threaded camshaft
Special version hollow shaft DIN 5463
Special version angle adjustment
HKS Unternehmensgruppe
Leipziger Straße 53-55D-63607 Wächtersbach-Aufenau
Phone: +49 (0)6053 / 6163 - 0Extension Const. -11 / Sales. -21Telefax: +49 (0)6053 / 6163 - 39
E-Mail: [email protected]: www.hks-partner.com
Dimension table
Typ DA-H 300A m 6 180DIN 5480*) W 180x5x34x8fB Ø 555C f 7 Ø 380D 285E Ø 440F Ø 470G 10H DIN 6885 280I DIN 6885 45J DIN 6885 100K 500L 300M 6N 20O 110P 90° 840
180° 1060270° 1285360° 1510
Q 271R 90° 194
180° 302270° 414360° 528
S 45° G 1“T 18°U Number 19U 32
Special version HW-hollow shaft toDIN 5480 on requestB 140Spline profile DIN 5472 130x145x24
Special version HWP - Hollow shaftwith key grooves (DIN 6885)H1 200J1 78,4CH7 Ø 140I1P9 36
*) Special version KW spline shaftDIN is not shown
N.B.: In the hollow shaft version it isnecessary to construct the shaft in ahigh strength material. A calculation ofthe shaft for torsional strength isstrongly recommended.
Special version with camshaftW f7 40W1 h6 25Special version with angleadjustment/camshaft/camshaftwith tapped hole/camshaft withpivotP1 90° 930
180° 1150270° 1375360° 1600