4,500 15,000 630 Max In (A) of Frame Model S400 Number of Poles 3, 4 Typ NE e Nominal current ratings I n (A) 50°C 250 400 Electrical characteristics Rated operational voltage U e (V) AC 50/60 Hz 690 - 800 8 DC Rated insulation voltage U i (V) Rated impulse withstand voltage U imp (kV) Ultimate breaking capacity I cu (kA) 690V AC 20 30 45 50 85 - 15 30 45 50 85 - (IEC, JIS, AS/NZS) 525V AC 440V AC 400/415V AC 220/240V AC 250V DC Service breaking capacity I cs (kA) 690V AC (IEC, JIS, AS/NZS) 525V AC 440V AC 400/415V AC 220/240V AC 250V DC Rated breaking capacity (NEMA) (kA) 480V AC 25 85 240V AC Rated short-time withstand current I cw (kA) 0.3 Seconds 5 Protection Adjustable thermal, adjustable magnetic Fixed thermal, fixed magnetic Microprocessor Utilisation category B Installation Front connection (FC) Extension bar (FB) • Cable clamp (FW) • Rear connection (RC) • • Plug-in (PM) DIN rail mounting (DA) - Dimensions height (mm) 260 140 185 103 4.2 5.6 width (mm) 3 pole (mm) 4 pole depth (mm) Weight weight (kg) 3 pole 4 pole Operation Direct Opening Action Toggle operation Door mounted (HS) / Breaker mounted handle (HB) • Motor operation (MC) • Endurance Electrical cycles 415V AC Mechanical cycles DATA SHEET: TEMBREAK 2 S400-NE MCCB Standard • Optional - Not Available TB2 E/S 630 Page 1 of 4 MCCB Electrical Characteristics to IEC 60947-2, EN 60947-2, JIS C 8201-2-1 ANN.1, AS/NZS 3947-2, NEMA AB-1
Transcript
4,50015,000
630Max In (A) of FrameModel S400Number of Poles 3, 4Typ NEe
Nominal current ratingsIn (A) 50°C 250
400
Electrical characteristicsRated operational voltage Ue (V) AC 50/60 Hz 690
-8008
DCRated insulation voltage Ui (V)Rated impulse withstand voltage Uimp (kV)
Ultimate breaking capacity Icu (kA) 690V AC 2030455085-
1530455085-
(IEC, JIS, AS/NZS) 525V AC440V AC400/415V AC220/240V AC250V DC
Service breaking capacity Ics (kA) 690V AC (IEC, JIS, AS/NZS) 525V AC
440V AC400/415V AC220/240V AC250V DC
Rated breaking capacity (NEMA) (kA) 480V AC 25 85240V AC
Rated short-time withstand current Icw (kA) 0.3 Seconds 5
Protection Adjustable thermal, adjustable magneticFixed thermal, fixed magneticMicroprocessorUtilisation category B
Operation Direct Opening ActionToggle operationDoor mounted (HS) / Breaker mounted handle (HB) •Motor operation (MC) •Endurance Electrical cycles 415V AC
Mechanical cycles
DATA SHEET: TEMBREAK 2 S400-NE MCCB
Standard • Optional - Not Available
TB2 E/S 630
Page 1 of 4
MCCB Electrical Characteristics to IEC 60947-2, EN 60947-2, JIS C 8201-2-1 ANN.1, AS/NZS 3947-2, NEMA AB-1
With extension bars (optional)
With extension bars (optional)
30
30
Front connected
Rear connected
Front connected with Motor Operator
Rear connected with Motor Operator
DATA SHEET: TEMBREAK 2 S400-NE MCCB
Outline Dimensions S400-NE
ASL: Arrangement Standard Line HL: Handle Frame Centre Line
Page 2 of 4
11
8 (max.)
20 (max.)
Preperation of conductor
30 (max.)
Support or rail
Support or rail
Mounting screwM10x30 max.
Mounting screw M5 x 20
Mounting plate
90102
260
97
4
102113
48
138142
180
6t6t
198
258
65
276
90102
260
971
4
32
6t32
204208
246
12
1
Insulating plate
Mounting plate
Mounting M6 NUT
Insulating plate
Mounting screw M6x70
Mounting on a support or rails (shown with optional connection bars oriented for rear access)
Mounting through the backplate (shown with optional connection bars oriented for rear access)
Mounting on the backplate (optional connection bars must be oriented for front access)
Outline Dimensions Termination of Busbar
ASL: Arrangement Standard Line HL: Handle Frame Centre Line
DATA SHEET: TEMBREAK 2 S400-NE MCCB
Outline Dimensions S400-NE Plug-in Version
Page 3 of 4
Percent Rated Current IRPercent Rated Current In
LT
ST
PTA
NP
Option
Standard
IR (A)LTD Pick-up current IR xIn 0.4 0.5 0.63 0.8 0.9 0.95 1.0
1Characteristics
Note(1) gF is not available when In is 250A. (2) Ii max. = 13 x In. (3) 1.0 x IR or 0.5 x IR can be selected. Characteristic of neutral protection (tN vs. IN) isidentical to characteristic of phase protection (tR vs. IR). (4) When you specify gF on MCCBs with 3 poles the terminal block is automatically fitted toconnect with the external neutral CT for 3 phases 4 wires system. See terminal blocks in section 4.
