DBALL-DBALL2-MIT1 EN IG TH20160212b...Feb 12, 2016 · ® Mitsubishi is a registered trademark and...

Index

® Mitsubishi is a registered trademark and property of its respective company.

Vehicle Application Guide................................................................................................................................................

Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)Wiring Diagram................................................................................................................................................................Vehicle Wiring Reference Chart.......................................................................................................................................Locating Components......................................................................................................................................................

ProgrammingModule Programming......................................................................................................................................................Module Reset & Hard Reset............................................................................................................................................Feature and Option List...................................................................................................................................................Feature Programming......................................................................................................................................................

LED Diagnostics and Troubleshooting............................................................................................................................

Limited One Year Consumer Warranty............................................................................................................................

Quick Reference Guide...................................................................................................................................................

02

030405

06070708

09

10

11

Door lock and transponder interface for Mitsubishi RVR (Smart Key) and Outlander Sport (Smart Key). Features include door trigger sensing, tach output, and FOB control.

Installation Guide

Update Alert: Firmware updates are posted on the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.

Rev.: 20160212

Platform: DBALL/DBALL2Firmware: MIT1

© 2016 Directed. All rights reserved.

Vehicle Application GuidePage 2

Vehicles

2015

2014

2013

2012

2011

PK

-Im

mobilizer

Bypass-D

ata

No

Key

Req'd

AV

-Panic

Mode

Activ

atio

n

DL-A

rmF

acto

ryS

ecurity

DL-D

isarm

Facto

ryS

ecurity

DL-D

oor

Lock

Contr

ol

DL-D

oor

Unlo

ck

DL-D

river

Priority

Unlo

ck

DL-T

runk

/H

atc

hR

ele

ase

FO

B-C

ontr

olo

fafterm

ark

etala

rmw

ithO

EM

rem

ote

RS

-Tach

/R

PM

Outp

ut

SS

-Entr

yM

onito

ring

ALL

Door

Pin

s

SS

-Entr

yM

onito

ring

Driver

Door

Pin

SS

-Entr

yM

onito

ring

Hood

Pin

SS

-Entr

yM

onito

ring

Tru

nk/H

atc

hP

in

ST

-Bra

ke

Sta

tus

(footbra

ke)

ST

-E-B

rake

Sta

tus

ST

-Igniti

on

Sta

tus

Mitsubishi

Outlander Sport (Smart Key) • • • • • • • • • • • • • D • • D • • • • D

RVR (Smart Key) • • • • • • • • • • • • • D • • D • • • • D

Legend:

D: Data-to-Data (D2D) only AV: Horn & Lights Controls RS: Remote Start & Engine Controls

•: D2D and Wire-to-Wire (W2W) DL: OE Door Lock & Alarm Controls SS: Integrated Security & Monitoring

FOB: Sync CAN Interface w / FOB Remote ST: Function/Feature Status

PK: Transponder & Immobilizer Override

Rev.: 20160212



Wiring DiagramRefer to the Locating Components in the Vehicle section on page 5 for more information.

C-4

08

C-413

C-412

C-411

1211

23

10

22

9

21

8

20

7

19

6

18

5

17

4

16

321

13 14 15 24

31 2

4 5 6

Rem

ote

Sta

rter

1: Green: (-) Lock Input

2: Blue: (-) Unlock Input

3: Red/White: Trunk Release Input

4: White/Violet: Aux1 Panic Input

9: Pink: (+) Ignition Input

10: Blue/White: (-) GWR (Status) Input

Ignition Connector White

(right side of steering column)

(+) 12V

(+) Parking Lights:Pink, pin 13

(+) Parking Lights:Yellow, pin 10

6 Ampdiodes

(-) Ground

(+) Parking Lights (+) 12V

(-) Ground(-) Ground

(-) GWR (Status)

(+) Ignition Output

(-) Lock Output

(-) Unlock Output

(-) Trunk Release Output

Aux1 Panic Output(-) Trunk Status Input

(-) Door Status Input

(+) Brake Status Input

(-) Hood Status Input

(-) E-Brake Status Input

[1] (AC) Tach Input

C-411White connector

1

8

3

1012

2

9

4

1113

5

14

6

15

7

16

C-412Brown Connector

C-413White Connector

18 3

1012

29 4

111317

5

1418

6

1519

7

1620

Fuse Box (front view)Driver-side Kick Panel

CAN connections can also be found in passenger kick panel or behind cluster,see Locating Components in theVehicle (Type 3) on page 10 for details.

(+) Accessory

(+) Starter

TX

(-) GroundRX

(+)12V

10

RF

Prog. Button

LED

4

14

12

2

DBALL/DBALL2 P#: XKD2D65

(-) Driver Door Trigger:Yellow, pin 16

(+) Ignition: White, pin 2

(+) Starter:Blue, pin 5

(+) Accessory: Light Green, pin 6

FT CAN Low:Red, pin 7

FT CAN High:Green, pin 6

Not required in D2D mode.

[1] Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.

All adapters are displayed from the wire side (unless specified otherwise).

[1] (AC) Tach Output: Violet/White: 5

(+) Brake Status Output: Gray: 6

(-) Hood Status Output: Blue/Red: 12

(-) Door Status Output: Green/White: 3

(-) E-Brake Status Output: Black/White: 1

(-) Trunk Status Output: Red/Black: 4

FT CAN High: Orange/Green: 5

FT CAN Low: Orange/Brown: 6

(+) 12V: Red: 13

(-) Ground: Black: 14

(-) Auto Headlamp Shutoff Output: Green/Black: 2

C-408Black Connector

12

(+) 12V:Black/Red,pin 1

Rev.: 20160212



Vehicle Wiring Reference Chart

Function Color Pin Polarity Location Color Pins

FT CAN High Green 6 Data C-411 at Fuse Box, driver kick panel White 24

FT CAN Low Red 7 Data C-411 at Fuse Box, driver kick panel White 24

Driver Door Trigger Yellow 16 (-) C-412 at Fuse Box, driver kick panel Brown 16

Parking Lights Pink 13 (+) C-413 at Fuse Box, driver kick panel White 20

Parking Lights Yellow 10 (+) C-413 at Fuse Box, driver kick panel White 20

Accessory Lt. Green 6 (+) Ignition Connector, left side of steering column White 6

Ignition White 2 (+) Ignition Connector, right side of steering column White 6

Starter (automatic transmission only) Blue 5 (+) Ignition Connector, left side of steering column White 6

(+)12V White 1 (+) C-408 at Fuse Box, driver kick panel Black 2

FT CAN High Green 6 Data C-411 at Fuse Box, driver kick panel White 24

FT CAN Low Red 7 Data C-411 at Fuse Box, driver kick panel White 24

Driver Door Trigger Yellow 16 (-) C-412 at Fuse Box, driver kick panel Brown 16

Parking Lights Pink 13 (+) C-413 at Fuse Box, driver kick panel White 20

Parking Lights Yellow 10 (+) C-413 at Fuse Box, driver kick panel White 20

Accessory Lt. Green 6 (+) Ignition Connector, left side of steering column White 6

Ignition White 2 (+) Ignition Connector, right side of steering column White 6

Starter (automatic transmission only) Blue 5 (+) Ignition Connector, left side of steering column White 6

(+)12V White 1 (+) C-408 at Fuse Box, driver kick panel Black 2

Mitsubishi RVR (Smart Key) 2011-2015

Wire Information Connector Information

Mitsubishi Outlander Sport (Smart Key) 2011-2015

Rev.: 20160212



Locating Components in the Vehicle

Ignition Connector White(left side of steering column)(+) Accessory: Light Green, pin 6(+) Ignition: White, pin 2(+) Starter: Blue, pin 5

C-413 - White Connector (at fuse box in driver-side kick panel)(+) Parking Lights: Yellow, pin 10(+) Parking Lights: Pink, pin 13

Cluster ConnectorC-203 - White(behind cluster)FT CAN High: Red, pin 14FT CAN Low: Pink, pin 15

Blue Connector(passenger kick panel)FT CAN High: Pink, pin 10FT CAN Low: Blue, pin 11

ETACS/ECU ConnectorC-408 - Black(at fuse box,in driver-side kick panel)(+) 12v: Black/Red

Page 5

C-412 - Brown Connector (at fuse box in driver-side kick panel)(-) Auto Headlamp Shutoff Output: Yellow, pin 16

Rev.: 20160212



Module Programming

4

3 The LED turns ON green for 3 seconds and shuts OFF.

Press the PTS button 1x to turn ignition OFF.

Without applying the brakes, press the PTS button 2x to turn ignition ON.2

&

IMPORTANT for PTS vehicles! Takeover is NOT possible. The vehicle will shut down if a door is opened.

1Solid

OffSolid x3 secs

Wait until the LED turns ON solid red.

You have successfully completed the module programming sequence.

ImportantMake all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.

Warning! To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.

When the flashing operation is successful, you can proceed with the programming instructions below.

Refer to the LED Diagnostics section on page 16 for more information and for troubleshooting purposes.

OR

If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to the module, then connect the 4-pin D2D harness.

D2D Installation

W2W Installation

If required for your installation, connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module.

10-pinD2D

st1

12-pin14-p

in

nd2

rd3

10-pinD2D

st1

th4

12-pin14-p

in

nd2

rd3

Flashing a module using your computer:

1. Connect the interface module to your computer using the XKLoader2.

2. Go to www.directechs.com using Internet Explorer, and select the Flash Module button.

3. Follow the instructions to select your vehicle, installation type, and configure your options.

4. Once you have configured the firmware options, click on the FLASH button.

Flashing a module using your smartphone or tablet

1. Connect the interface module to your XKLoader3.

2. Launch the Directechs Mobile app on your smartphone or tablet.

3. Select FLASH YOUR MODULE and follow the on screen instructions.

Press

PUSHENGINESTARTSTOP

Press 2x

PUSHENGINESTARTSTOP

Rev.: 20160212



Rev.: 20160212



2

Solid

&

Solid Flashes

&

Release

3

Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.

Release the programming button. The LED turns ON solid red.

Warning Against Executing a Hard Reset! A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.

1 OR

If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.

D2D Installation

If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

st1

12-pin14-p

in

nd2

th4

rd3

10-pinD2D

st1

th5

12-pin14-p

in

nd2

rd3

th4

Module Reset

Hard Reset

2 & &Solid SolidRelease

Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red.

A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed to the module using the web config tool will not be affected.

1 OR

If required for your installation, connect the 10-pin, 12-pin & 14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.

D2D Installation

If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.

W2W Installation

10-pinD2D

st1

12-pin14-p

in

nd2

th4

rd3

10-pinD2D

st1

th5

12-pin14-p

in

nd2

rd3

th4

Page 7

Feature and Option ListPage 8

Features Operation Option Description

No RF Output*Module is connected to a remote starter

using a standard installation.

RFTD OutputModule is connected to an XL202 using an

RSR or RXT installation (when available).

* Default Option

1RF Output type Activate this feature w henever an external RFTD

module is used (i.e. XL201 or XL202).

To enter feature programming routine- Turn the ignition ON, then OFF. - Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the

Programming button.- The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate

the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.

Changing feature options- Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature. - The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly

the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.

Accessing another feature- Press and release the programming button a number of times to advance from the current feature to the next desired feature. - The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to

indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.

When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.

Once a feature is programmed- Other features can be programmed.- The feature programming can be exited.

Exiting feature programming- No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming

sequence.OR

- Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.

Feature ProgrammingProgramming

Button

Rev.: 20160212



LED Status Description Troubleshooting

Module Programming

Solid red Waiting for the ignition to turn on.

Make sure that all the connections are correct (see

install sheet) and turn the ignition ON to begin the

programming sequence.

Flashes orangeCAN has been successfully

detected.

Make sure you keep the key to the ON position long

enough to let the programming finish.

Flashes greenVehicle has been successfully

detected.Normal operation.

Solid green for 3

seconds

Module has been successfully

programmed.Normal operation.

Active Ground While Running

Flashes green Ground out (GWR) is active. Normal operation.

Off Normal operation.

The Ground While Running (status) wire is incorrectly

connected. Refer to the wiring diagram to make the right

connections.

Inactive Ground While Running

Flashes green once Lock function has been executed.

If it does not flash, the bypass module did not receive the

signal. Verify the connections between the bypass and

the remote starter module.

Flashes green twiceUnlock function has been

executed.




Flashes green 3 timesTrunk release function has been

executed.




Page 9

LED Diagnostics and Troubleshooting

Solid

Solidgreenx3 sec

Flashesorange

Flashesgreen

Flashesgreen x1

Flashesgreen x2

Flashesgreen x3

Flashesgreen

Off

Rev.: 20160212



For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.

This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.

TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.

This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com

920-10012-01 2013-07

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.

Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876 B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1; 7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:

Limited One Year Consumer WarrantyPage 10

Rev.: 20160212



Quick Reference GuideDBALL/DBALL2-MIT1


Button(s) Actions

Press & hold for 1 second to lock.

Press & hold for 1 second to unlock.

Press & hold for 1 second to remote

start.

Press & hold for 5 seconds to activate

the trunk release (optional).

Press once, then to activate the

rear hatch/tail glass release (optional).*

Press 3 times, then to activate

the panic mode.

Press once, then to reset the

remote starter runtime.

List of Available Commands

x1 +

x3 +

x1 +

* This output is configurable. see your authorized installation center for more information.

Note that the information below is for Viper, Clifford and Python models. Icons and commands may differ depending on the remote brand and model purchased. Refer to your authorized installation center for more information.

Notes

1: Index2: VAG3: WD4: RC5: LOC6: Prog7: Reset8: Feature Prog9: LED diag10: WarrantyDBALL-DBALL2-MIT1_EN_QRG_TH20160119.pdf1: User

Date post:	19-Feb-2021
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

DBALL-DBALL2-MIT1 EN IG TH20160212b...Feb 12, 2016 · ® Mitsubishi is a registered trademark and...

Documents