DOUBLE AND SINgLE HUNg WINDOW HArDWArE
tilt Latches
balance Shoes
Sash bracket
Weep Hole Covers Reversible Lock Slot
Sash Lifts
thumb button
End Cap
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
SASH HArDWArE
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D1
Part Dimensions Number A b C D E F G H i J
LCS091 .103 1.976 .071 .555 .228 .340 .492 .655 .391 .220
The LCS091 thumb button is a more affordable alternative to other currently available thumb buttons. The clip prongs can be altered to fit most latches. No visible parting line and textured finish are an improvement over other thumb buttons. Standard industry colors available.
LCS091 thumb button
Cb
AD
EF
iH
GJ
SASH HArDWArE
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D2
Part Dimensions Number A b C D E F G H i J
LCSR719 .440 1.125 .535 .225 .935 .186 .485 .085 .365 1.00
LCSR719 Reversible Lock Slot is a receiver for a sweep style lock, found on many single hung windows.
LCSR719 Reversible Lock Slot
Cb
A
D
E
F
i
H
G
J
SASH BrACKET
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D3
WEEP HOLE COVErS
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D4
Part Dimensions Number A b C D E F G H i J
LCS070 .265 .125 .870 .530 .265 1.380 .230 .265 .20 .75
LCS070 is a Hooded Weep Hole Cover that snaps into pre-existing slots. The grid bars prevent entry of insects.
Cb
AD
E
F
i
H
G
J
Part Dimensions Number A b C D E F
LCSR710 .280 .110 .680 .215 .165 .945
The LCSR710 Weep Hole Cover is a downsized style used for low volume water escape.
LCSR710 Weep Hole Cover
LCS070
C b
A
D
EF
WEEP HOLE COVErS
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D5
LCS068 and LCS068C super tough nylon Weep Hole Covers allows water drainage. The flap shuts after drainage, preventing air infiltration. LCS068 and LCS068C snap fit into your aluminum and vinyl application. Two leg widths and standard industry colors are available.
LCS068 Weep Hole Cover
LCS068C Weep Hole Cover
Part Dimensions Number A b C D
LCS068 .390 .990 1.400 .050
LCS068C .390 .760 1.400 .050
WEEP HOLE COVErS
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D6
The LCS077R/Filled Weep Hole Cover with double sided tape backing.The LCS077 super tough nylon Weep Hole Cover is similar to the LCS068, allowing water drainage. The flap shuts after drainage, preventing air and debris infiltration. Oval profile, large size and push fit assembly offer another choice to fit your weep hole demands. Standard industry colors are available.LCS077R has the same sizing and function as the LCS077. Screw tabs offer another fastening option for your weep hole requirements.
LCS077 Weep Hole Cover
LCS077R Weep Hole Cover
Part Dimensions Number A b C D E
LCS077R/Filled 2.510 .510 — — —
LCS077 2.510 .510 1.890 .105 —
LCS077R 2.485 .510 1.890 .105 .150
b
A
Cb
A
D
CbA
D
E
SASH LIFT
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D7
Versatile, warm to the touch, the LCS023 Sash Lift can be used with vinyl, wood, or aluminum windows. Application is easy with two screw slots. Polycarbonate gives its strength for a lifetime of use. Hot stamping and pad printing are available for personalized company logos.Uses 2 #8 screws.Industry colors available.
LCS023 Sash Lift
LCSR717
Part Dimensions Number A b C D
LCS023 .250 4.000 .740 3.265
b
D
AC
LCSR717 is a recessed style, sash lift, attaches by using 2 #8 screws. Industry colors available.
C
b
A D
E
F
iHG
Part Dimensions Number A b C D E F G H i
LCSR717 3.200 3.00 1.490 .160 1.050 .480 .840 .375 .750
END CAP
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D8
LCS092 End Caps are used to set off the lift rails on the top and bottom sash. The contour design offers an attractive alternative to a box plug. Standard industry colors available. A standard end cap for VBP windows.
LCS092 End Cap
b
A
D
E
F
G
C
Part Dimensions Number A b C D E F G
LCS092 .325 .145 .540 .600 .35 .460 .920
BALANCE SHOES
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D9
“NEW BALANCE SHOE SIZES”
The addition of NEW Balance Shoes Sizing options permits better choices for our customers at substantial savings.
NEW IMPROVED FEATURES: • Allows Easy Sash Takeout on LCS105A,
106 & 107 Balance Shoes. • Locking Cam Secures Pivot Bar During
Transportation and Installation (LCS105A, 106 & 107 only.)
• NEW Shoe Sizes Allows for Variations in Pocket Sizes, FOR BETTER HOLDING POWER.
• Front to Back Positive Locking Mechanism.
• Balance Shoes Work with both Block & Tackle and Spiral Balances.
The LCS Balance Shoe Family PART NO. POCKET SIZE LCS101 1-1/4" x 17/32" LCS101A 1-1/4" x 9/16" LCS101B 1-1/4" x 39/64"
LCS105A* 1" x 3/8" LCS106 1" x 9/16" LCS107 1" x 9/16" (*Addedgripforaslightlythickerpocket.)
(447-LCS110 Pivot Bar Fits The LCS105A & LCS106 Balance Shoes.)
CheckOutOurCompetitivePricing.
PART NUMBER A B C D*
LCS101 1.25 2.10 .530 .605
LCS101A 1.25 2.10 .560 .615
LCS101B 1.25 2.10 .609 .655
LCS105A .970 2.025 .350 .420
LCS106 .970 2.025 .545 .580
LCS107 .970 2.025 .545 .605
LCS105ALCS106LCS107
LCS101LCS101ALCS101B
* D is the locked position of dimension C.
PIVOT BAr
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D10
LCS105A, LCS106 and LCS107
TILT LATCHES
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D11
The 452tL1 and 452tL2 are surface mounted tilt Latches. The 452tL1 tilt Latch is styled with rounded corners and the 452tL2 is a traditional styled Tilt Latch with non-rounded corners. Both latches are available as a left or right hand latch.
• Made with Engineered Nylon
• Available in Colors
• Affordably Priced
• “Plastic” the warm technology always energy efficient.
452tL1 & 452tL2 tilt Latches
Dimensions Part Number A b
452tL1 tilt Latch .940 2.60
452tL2 tilt Latch 1.10 2.80
SWEEP LOCK
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D12
452SL Sweep Lock
• Has Passed 185 lb. Vertical and 75 lb. Horizontal Testing
• 20% Glass Filled Nylon (An industry standard, proven strong and reliable.)
• AVAILABLE IN COLORS: White-1 • Black-2 • Tan-3 • Bronze-4 *Custom color matching and logo insert available.
Call for competitive pricing and quantity price levels.
“Plastic” the warm technology always energy efficient.
An inexpensive Alternative to Metal Sash Locks.
452SL Sweep Lock
Dimensions Part Number A b
452SL Sweep Lock 2.89 0.78
SASH LOCK KEEPEr
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D13
LCSR794 Sash Lock Keeper
• Snap in fit.
• A nylon receiver for knife style locks.
• Available in industry standard colors or custom color matches available.
LCSR794 Sash Lock Keeper
FrAME COrNEr KEY
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D14
LCSR632 Corner Key fits a “tapered ” extrusion.
Corner Key Options:
• Available with or without Locking clips.
• Available with or without a weatherable mitered corner joint.
LCSR632 Frame Corner Key
*Drawing is representational, actual part may deviate from drawing.
LOCKINg HOLE PLUg
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D15
LCS360 Locking Hole Plug
A heat stabilized nylon Locking Hole Plugs. These plugs were designed with a positive snap action that ensures a secure fit. Cap heads can be colored to match your requirements or are available in white.
LCS360 Locking Hole Plug
Part Number Diameter
LCS 360 .562
LCS 361 .187
WINDOW SLIDE PLATE & BOTTOM PrOTECTOr
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D16
LCS601 WiNDOW SLiDE PLAtE & bOttOM PROtECtOR
Moving oversized, awkward and heavy units are a pain and can be dangerous. Now handling these clumsy units can be more manageable with the LCS601.
• Windows slide & skid easier for effortless transport.
• Protects window bottoms during transportation.
• More economical than wood skids.
• Helps Prevent window damage prior to installation.
• Can be stapled or screwed to window bottom.
• Raises window over 1/2" off the floor.
LCS 601 Window Slide Plate & bottom Protector
LCS 601 Window Slide Plate & bottom Protector
119 South 2nd Street • Waterville, MN 56096 • 507-362-8685 • FAX 507-362-8893 • E-mail: [email protected]
www.lcsplastics.com
D17
LCSR776 COiL bALANCE HOLDER
‘Egress’ with a 3' x 5' Window* Now Available using the LCSR776 Coil balance Holder
The LCSR776 Coil Balance Holder attaches above the meeting rail line and the unique part design allows tilt latches to slide over the Coil Balance Holder so the sash can be raised to its maximum.
• Permits the bottom sash to raise higher.
• *Provides egress square footage requirement using a 3-0 x 5-0 unit.
• Fits a standard 1-1/2" x 1/2" balance pocket. Other sizes available in the future.
• Holds two 3/8" coil balances. (Balances of this part can be purchased from: Evan's Son's Inc., 1 Spring Ave., Lansdale, PA 19446 215-368-7700 / 215-368-9019 fax)
• Comes in white and tan, custom colors available.
• Potential Savings of $3-$4 per unit by not using a 3-0 x 5-4 size.
*Some units may not reach egress because of limitations other than coil balance holder.
LCSR776 Coil balance Holder
COIL BALANCE HOLDEr