e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs
of Sagar Zone
TENDER SPN NO: JDSD-SGO/SP/TEN/2015-16/ 01
FOR THE YEAR
2015-2016
OFFICE OF THE JOINT DIRECTOR
SKILL DEVELOPMENT (ITIs) – SAGAR ZONE
Khurai Road, SAGAR – 470002 (MP)
Phone 07582-266814, E-Mail: [email protected], Website: www.mpdt.nic.in
[I]
Table of Contents
1. Tender Notice (NIeT) ............................................................................................................................................ 1
2. Tender Rules ............................................................................................................................................................. 3
2.1. Scope of Tender ......................................................................................................................................... 3
2.2. Eligibility Criterion .................................................................................................................................. 3
2.3. Earnest Money Deposit (EMD) ........................................................................................................... 4
2.4. Validity of Tender ..................................................................................................................................... 4
2.5. Preparation and submission of Tender ........................................................................................... 4
2.6. Tender Prices ............................................................................................................................................. 5
2.7. Deviation ...................................................................................................................................................... 5
2.8. Opening of Tenders ................................................................................................................................. 5
2.9. Evaluation of Tenders ............................................................................................................................. 5
2.10. Award of Contract .................................................................................................................................... 6
2.11. Placement of Purchase Orders and Delivery Requirements .................................................. 6
2.12. Quality Testing Requirements: ........................................................................................................... 7
2.13. Payment Terms ......................................................................................................................................... 7
2.14. Settlement of Disputes ........................................................................................................................... 7
3. E-TENDERING PROCESS ...................................................................................................................................... 8
3.1. Registration of Bidders on e-Procurement System .................................................................... 8
3.2. Digital Certificates .................................................................................................................................... 8
3.3. Set Up of Bidders' Computer System ................................................................................................ 9
3.4. Publishing of N.I.T. ................................................................................................................................... 9
3.5. Key Dates and time .................................................................................................................................. 9
3.6. Downloading of the Tender Documents ......................................................................................... 9
3.7. Payment for registration on E-tendering portal .......................................................................... 9
3.8. Payment of tender document fee ....................................................................................................... 9
3.9. Preparation of Bids and Submission of Online Bids by the Bidders.................................... 9
3.10. Submission of Earnest Money Deposit ......................................................................................... 10
3.11. Opening of Tender ................................................................................................................................ 10
3.12. Contact Details ........................................................................................................................................ 10
e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs of Sagar Zone
Joint Director Skill Development – Sagar Zone
Pag
e1
1. Tender Notice (NIeT)
e-Tender Notice
The Joint Director, Skill Development (ITIs) – Sagar Zone, Woman ITI Campus,
Khurai Road, SAGAR – M.P. Invites online bids (Two bid system) from Manufacturers or
Authorized dealers for Supply of Tools, Equipment's and Machines for ITIs of Sagar Zone as
below :
Tender No
Description Earnest Money
Deposit Bid Document
Price
01 Mechanical & Electrical Machine INR 100000 INR 1000
2. Online bidding go through https://www.mpeproc.gov.in and online e-tenders are
invited as per key dates from Manufacturers or their Authorized Dealers for Supply of
Tools, Equipment's and Machines for ITIs of Sagar Zone Madhya Pradesh. Tender
document and other details are also available at the websites
https://www.mpeproc.gov.in, www.tender.gov.in and www.mpdt.nic.in
3. In all respect the hard copy of the Bids (Envelope-A along with Earnest money, and
Envelope-B) must be received at the office of the undersigned latest by 3:00 PM on
19/01/2016 and will be opened ONLINE Technical Tender (Envelope-A) on the same day
i.e. 19/01/2016 at 4:00 PM. In the presence of such tenderer or their authorized
representatives as may be present.
4. All corrigendum/ amendments/changes if any will only be issued and made available only
on https://www.mpeproc.gov.in.
(Sunil Choudhary)
Joint Director
Skill Development(ITIs)Sagar
e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs of Sagar Zone
Joint Director Skill Development – Sagar Zone
Pag
e2
Key Dates and Time
SN Task Date & Time
1. ONLINE BID DOCUMENT
PURCHASING END DATE 19/01/2016, 12:00 HRS
2. BID CLOSING FOR SUBMISSION
ON ONLINE BIDS 19/01/2016, 14:00 HRS
3.
SUBMISSION OF HARD COPY OF
BIDS (Envelope – A along with
EMD, and Envelope – B)
20/01/2016, 15:00 HRS
4. ONLINE OPENING OF THE
TECHNICAL BIDS 20/01/2016, 16:00 HRS
5. ONLINE OPENING OF THE
FINANCIAL BIDS 25/01/2016, 12:00 HRS
Note: Soft copy (In prescribed Excel & Word Format) and Hard Copy of the Bid should be same, if in
case of any difference/discrepancy Soft Copy will be considered.
e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs of Sagar Zone
Joint Director Skill Development – Sagar Zone
Pag
e3
2. Tender Rules
Scope of Tender
The Joint Director, Skill Development (ITIs) – Sagar Zone, Woman ITI Campus Khurai Road, SAGAR
– M.P. (hereinafter referred as Tender Inviting Authority and/or Tender Acceptance Authority
and/or Ordering Authority unless the context otherwise requires) Invites online bids (Two bid
system) from Manufacturers or Authorized dealers for Supply of Tools, Equipment's and Machines
for ITIs of Sagar Zone as below :
Tender
No Description
Earnest Money
Deposit
Bid Document
Price
01 Mechanical & Electrical Machine
INR 100000 INR 1000
Eligibility Criterion
The Tenderers should fulfil the following eligibility criteria:
a) The Tenderer should be Manufacturer or Authorized Dealer having relevant Licence of
Manufacturer/ Authorized Dealer and such a Registration should be valid as on the date
of Tender submission. as per Annexure -2
b) The Tenderer should have achieved annual turnover as follows (every FY) in the last
three financial years, backed by practicing chartered accountant.
Tender
No Description Minimum Annual Turnover
01 Mechanical & Electrical Machine
100 Lakhs
c) The Tenderer (and tenderer’s principal manufacturer, if tenderer is Authorized Dealer)
should not be blacklisted either by the Tender Inviting Authority or by any State
Government or by Government of India. An undertaking by the tenderer should be
submitted in this regard certifying that the tenderer or its principal manufacturer (if
applicable) is eligible to participate in the bid process. as per Annexure.4(Compliance of
Tender)
d) The Manufacturer should be in the business of manufacturing of similar equipment for a
period not less than 5 Years.
e) The Tenderer should furnish the information on past 2 years supplies and satisfactory
performance inAnnexure – 3.
f) The Tenderer must submit the latest Sales Tax/VAT Tax clearance certificate.
g) The Tenderer must submit the Form –“A” on letterhead with signature &
stamp.Annexure-1
e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs of Sagar Zone
Joint Director Skill Development – Sagar Zone
Pag
e4
Earnest Money Deposit (EMD)
a) All tenders must be accompanied with Tender-wise EMD (Hard Copy) along with
Technical (Physical) bid.
b) The EMD should be submitted in the form of Demand Draft of Nationalized
Bank/Scheduled Bank in Favour of “Joint Director, Skill Development, (ITI's)Sagar
Zone” Payable at Sagar. Earnest Money submitted in any other form will not be
accepted and the tender will be rejected.
c) Earnest Money/Security Deposit to this office in previous tenders will not be adjusted
towards the present tender and no request will be entertained in this regard.
d) Industries registered as Small scale industrial units with the Director of Industries,
Government of Madhya Pradesh, Bhopal only will be exempted from depositing the
Earnest money; however they should send a true copy of the certificate for claiming the
above exemption. Firms registered with the Director General of Supplies and Disposals
and small Scale Industrial Units registered with Central Govt. or with other State
Government are not exempted from depositing earnest money.
e) The EMD shall be refunded to the unsuccessful tenderer after finalization of the contract. It
shall be refunded to the successful tenderer on receipt of the performance security deposit.
f) The EMD will be forfeited, in case Tenderer withdraws its Tender during the validity of
bids OR the successful bidder who fails to sign the contract agreement.
Validity of Tender
a) The Tender will be valid for a period of 12 Months after the due date of submission of
Tenders. A Tender valid for a shorter period shall be rejected by the Tender Inviting
Authority as non-responsive
b) In exceptional circumstances, prior to the expiration of the Tender validity, the Tender
Inviting Authority may request the Tenderers to extend the Tender validity for further
period as deemed fit. The request and the responses thereto shall be made in writing. A
Tenderer may refuse the request without forfeiting its EMD. A Tenderer, agreeing to the
request will not be required or permitted to modify its Tender.
Preparation and submission of Tender
a) The Tender should be Computerised and every correction and interlineations in the bid
should be attested with full signature by the tenderer, failing which the bid will be
treated as ineligible. Corrections done with correction fluid should also be duly attested.
b) Bidder should give all relevant particulars about every item, such as maker’s name
Country of Manufacture and Specifications and Price etc.
c) Articles for which rate contracts are available with the D.G.S.& D. Government of
India, New Delhi. The bidder should enclose the copy of the rate contract agreement
along with the tender.
d) Authorized dealer should submit the certificate from its manufacturer as proof to
purchase supplied items from OEM.
e) All documents/papers should be numbered, signed and sealed by the Tenderer on each
page.
f) The Tender is required to be prepared and submitted in two parts viz. ‘Part A -
Technical Bid’ and ‘Part B - Price Bid’.
g) The ‘Envelope of Part-A Technical Bid’ shall contain all essential documents for
Technical Tender. Such documents attached as per Annexure-8 to (Online & Physical).
e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs of Sagar Zone
Joint Director Skill Development – Sagar Zone
Pag
e5
h) The ‘Envelope of Part-C- Financial Bid’ shall contain duly filled, stamped and signed
Price Schedule in the format provided in Annexure – 5.
i) The Online tenders as above should be submitted on www.mpeproc.gov.in as per
Scheduled date and time.
j) Tender submitted or received after the closing date and time will not be considered and shall
be returned to the Tenderer unopened.
Tender Prices
a) Tender has been called for in the names of Items. The Tenderers should quote the rates
for the Items mentioned in Annexure – 10. The composition and Specification of each
item should be as per details given in Annexure – 10.
b) The Tenderer should mention the name of manufacturer of the item being quoted.
c) The rates should be quoted in format of Price Schedule shown in Annexure-5. Rates quoted
in any other format tender will be rejected.
d) Rates inclusive of Excise Duty, Customs duty, transportation, insurance, and any
incidental charges, but exclusive of State VAT/CST should be quoted for each of the
required item, separately on door delivery basis (FOR Destination, at Stores) as per
format of Price Schedule given in Annexure – 5.
e) Quoted rates are valid up to one year from the date of signing of contract agreement
and shall be firm during the currency of the contract.
Deviation
If the Tenderer submits the offer with deviation for any item then Deviation statement
should be submitted for every offer. In the absence of this the purchaser reserves the right
to accept or reject the bid of that particular item. Bidder should submit Deviation statement
as per Annexure-9. No other formats will be accepted. In absence of deviation statement the
tender will be rejected.
Opening of Tenders
a) The Tenders shall be opened at the scheduled date, time and venue by the committee
constituted by the Tender Inviting Authority. The Tenderers’ representative may
attend the Tender opening.
b) Technical Bid shall be opened first Online and the envelopes containing Technical Bid
along with EMD shall be opened physically.
c) The date and time of opening of Price Bid shall be informed to all such Tenderers who
qualify in technical Bid evaluation. The tenderer’s representative may choose to attend
the opening of Price Bid.
d) In the event, the date of opening as above is declared government holiday; the tenders
shall be opened at the same time on the next working day.
Evaluation of Tenders
a) The purchase committee, constituted by the Tender Inviting Authority, shall evaluate
the tender with reference to technical requirements and various other commercial
criteria given in the Tender Document.
e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs of Sagar Zone
Joint Director Skill Development – Sagar Zone
Pag
e6
Award of Contract
a) Security Deposit to the extent of 5% of the total value of the order in the form of
FDR/Bank Guarantee (in Performance Security Form- as per Annexure-7) will have to
be deposited by the successful Bidder before the final orders are placed with him.
Security Deposit should be submitted in favour of the Joint Director Skill
Development (ITI's) Sagar Zone Woman ITI Campus Khurai Road Sagar M.P.If the
demanded security deposit to the extent of 5% is not deposited by the bidder in the
specific period the Earnest Money already deposited with the tender is liable to be
forfeited.
b) Bid Security should have the validity period of 16 months.
Placement of Purchase Orders and Delivery Requirements
a) The Tender Inviting Authority shall place individual Purchase Orders for supply of
Items during the period of 1 year from the date of award of contract with successful
Tenderer(s). Tender Inviting Authority reserves the right to extend the validity of
purchase order further by 3 months on the same rates and terms & conditions of the
contract.
b) The supplier should complete the supply at the respected Govt. Industrial Training
Institute(ITI) situated at various location of Sagar Zone within 45 days from the date of
issue of purchase order.
c) If at any time the Tenderer has, in the opinion of the Tender inviting authority, delayed
the supply of Items due to one or more reasons related to force Majeure events such as
riots, mutinies, wars, fire, storm, tempest or other exceptional events, the time for
supplying the Items may be extended by the Tender inviting authority/ordering
authority at its discretion for such period as may be considered reasonable. However
such extension shall be considered only if a specific written request is made by the
Tenderer within 7 days from the occurrence of such event. The exceptional cause does
not include scarcity of raw material, power cut and labour disputes.
d) According to the M.P. Store Purchase Rules, 30% of total purchase will be made from
that Manufacturer/Authorized Dealer/Firm who has more than 50% partnership of the
persons belonging to SC/ST category. If the Manufacturer/Authorized Dealer/Firm who
has more than 50% partnership of the persons belonging to SC/ST category does not
participate in the tender then purchaser will call the list of such
Manufacturer/Authorized Dealer/Firm from the District Industries Centre (DIC) and
may place the order up to the 30% value of tender to the eligible SC/ST firms on the
accepted lowest rates.
e) The undersigned reserves the rights for any changes/cancellation/rejection of any part
or whole tender, without assigning any reason what so ever.
f) Warrantee/Guarantee should be for a period of minimum 1 year.
g) All consignment must be dispatched freight paid to concern ITI “To pay” Railway
Receipt/Freight Receipts will not be accepted. Loading /Unloading charges shall be
borne by the supplier.
h) It must be noted that normally all correspondence and transactions will be made only
with the parties whose tenders have been accepted and not with anybody else.
i) The undersigned reserves the right to split up the order for supply of articles at tender
for amongst more than one tender.
e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs of Sagar Zone
Joint Director Skill Development – Sagar Zone
Pag
e7
Quality Testing Requirements:
a) The Tender inviting authority may ask for samples and demonstration of any particular
item quoted by the bidders. The bidders shall have to submit samples and give
Demonstration in the prescribed time limit. In case the samples are not produced in the
prescribed time it shall be open to the undersigned to forfeit Earnest Money Deposited
by the bidder.If the samples sent by the party are approved the same will be adjusted in
regular supply and in the case of rejection, they will be returned back to the party at his
cost.
b) The Items including its packing (packaging), to be supplied, shall be of the best quality
and shall comply with the specifications given in the Tender Document.
c) All Items should be supplied with quality certificate. The undersigned may get the items
inspected by such person or persons he deems fit and to reject such of these items as in
his opinion do not come up to the specification. The decision of the undersigned will be
final in such cases. The rejected items will be returned on the bidder’s cost.
d) If any of the Items supplied by the tenderer, found to be ‘Not of Standard Quality’ after
the delivery, the tenderer should supply the whole Item quantity again irrespective of
consumption of that particular. The balance stock, if any, should be taken back within 7
days by the supplier at his/her own cost otherwise the authority will destroy it and no
claim in this regard shall be entertained.
e) Guarantee Certificate: - The Bidder will have to submit the GUARANTEE CERTIFICATE
as per Annexure – 6. Warrantee/Guarantee should be for a period of minimum 1 year.
Payment Terms
a) The 90% payment shall be released within 30 days from the date of receipt of accepted
Items and upon submission of claim for payment supported by Invoice (in triplicate),
and remaining 10% after successful working of item in duration of 2 months. However,
if supplied Items are found not as per specifications, then whole payment will be
withheld and shall be released only after receipt of replacement of Items which were
found not of standard quality.
Settlement of Disputes
a) In the event of any dispute arising out of the tender or orders such dispute would be
subject to the jurisdiction of Courts of Madhya Pradesh nearest to the place of Tender
Inviting Authority.
e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs of Sagar Zone
Joint Director Skill Development – Sagar Zone
Pag
e8
3. E-TENDERING PROCESS
Registration of Bidders on e-Procurement System
Manufacturers or their Authorized Dealers for Supply of Tools, Equipment's and Machines for ITIs
of Sagar Zone are required to register on the e-Procurement System on the website
https://www.mpeproc.gov.in in order to participate in tenders processed by Directorate of Skill
Development using E-Procurement system of IT department.
E-tendering Helpdesk at TCS, Bhopal Tel. No.18002588684
Digital Certificates
The Bids submitted online should be signed electronically with a Class III Digital Certificate to
establish the identity of the bidder submitting the bid online. The Bidders may obtain Class III
Digital Certificate issued by an approved Certifying Authority authorized by the Controller of
Certifying Authorities, Government of India. A Class III Digital Certificate is issued upon
receipt of mandatory identity proofs along with an Application Form. Only upon the receipt of
the required documents, a Digital Certificate can be issued. For details please visit
www.ccc.gov.in
Please note that it may take upto 7 working days for issuance of Class III Digital
Certificate, hence the bidders are advised to obtain them at the earliest.
The Bidders may obtain more information and the Application Forms required to be
submitted for the issuance of Digital Certificate from the e -Procurement, IT
Department, Arera Hills, and Bhopal.
E-tendering Helpdesk at TCS, Bhopal Tel. No.18002588684.
E-mail :- [email protected]
Important Note
Bid for a particular tender can be submitted during the ONLINE BID SUBMISSION stage only using the
Digital Certificate that is used to encrypt the data during the ONLINE BID PREPARATION.
In case, during the process of a particular tender, the bidder looses his Digital Certificate because of any
problem (such as misplacement, virus attack, hardware problem, operating system problem, etc.); he
may not be able to submit his bid online. Hence, the bidders are advised to keep their Digital
Certificates in a safe place under proper security.
The digital certificate issued to the Authorized User of a Partnership firm / Private
Limited Company / Public Limited Company / Joint Venture and used for online bidding
will be considered as equivalent to a no-objection certificate / power of attorney of that
user.
In case of Partnership Firm, majority of the Partners have to authorize a specific
individual through Authority Letter signed by majority of the Partners of the firm.
In case of Private Limited Company, Public Limited Company, the Managing Director /
any other Person (having designated authority to authorize a specific individual) has to
authorize a specific individual through Authority Letter.
Unless the certificate is revoked, it will be assumed to represent adequate authority of
the specific individual to bid on behalf of the Organization for online tenders as per
Information Technology Act, 2000. This Authorized User will be required to obtain a
e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs of Sagar Zone
Joint Director Skill Development – Sagar Zone
Pag
e9
Digital Certificate. The Digital Signature executed through the use of Digital Certificate of this
Authorized User will be binding on the firm. It shall be the responsibility of
Management/Partners of the concerned firm to inform the Certifying Authority, if the
Authorized User changes, and apply for a fresh digital certificate for the new Authorized User.
Set Up of Bidders' Computer System
In order for a Bidder to operate on the e-Procurement System, the Computer System of the
Bidder is required to be set up for Operating System, Internet Connectivity, Utilities, Fonts,
etc. A help file on setting up of the Computer System can be obtained from e-Procurement Cell
(M/s. TCS Limited, 5th Floor Corporate Block, DB Mall, Bhopal).
Publishing of N.I.T.
For the Tenders processed using the e-Procurement System, only a brief Advertisement
related to the Tender shall be published in the newspapers and the Detailed Notice and terms
and conditions of tender shall be published only on the e-Procurement System. The bidders can
view the Detailed Notice, Terms & Conditions of tender document and the time schedule for all
the Tenders processed using the e-Procurement System on the website
https://www.mpeproc.gov.in
Key Dates and time
The Bidders are strictly advised to follow the time schedule (Key Dates and time) of the
tender for their side of tasks and responsibilities to participate in the tender, as all the
stages of each tender are locked before the start time and date and after the end time and
date for the relevant stage of the tender as set by the concerned Department Official.
Downloading of the Tender Documents
The tender documents can be downloaded online from the website https://www.mpeproc.gov.in. All
the Bidders are required to register on the e-Procurement System of IT Department of Madhya
Pradesh website https://www.mpeproc.gov.inin order to participate in tender.
Payment for registration on E-tendering portal
The registration fee Rs. 500/- + taxes applicable is to be paid ONLINE. And details of payment
are required to email on [email protected] , [email protected],
Payment of tender document fee
Although the tender document can be downloaded from the website http://www.mpeproc.gov.in,
the bidder has to pay a sum of INR 1000 (Rupees One Thousand only) towards tender document fee
by way of Online.
Preparation of Bids and Submission of Online Bids by the Bidders
The Bidders have to prepare their Bids online, encrypt their bid data in the bid forms and
submit documents required to be uploaded related to the tender as per the time schedule
mentioned in the key dates and time as given in the Notice Inviting Tender after signing of the
same by the Digital Signature of their authorized representative.
e-Tender | Supply of Tools, Equipment's and Machines for Govt. ITIs of Sagar Zone
Joint Director Skill Development – Sagar Zone
Pag
e10
Submission of Earnest Money Deposit
The manufacturers or their Authorized Dealers shall submit their Earnest Money Deposit as usual in a
physically sealed Earnest Money Deposit envelope and the same should reach the concerned office
as stated in the Notice Inviting Tender and key dates.
Earnest Money should be submitted in the form of Demand Draft of Nationalized Bank/Scheduled
Bank in Favour of “Joint Director, Skill Development, (ITI's)Sagar Zone”Sagar MP.
The manufacturers or their Authorized Dealers has to upload scanned copy of Earnest
Money Deposit instrument along with the reference details in the relevant field during online
bidding.
Opening of Tender
The concerned Department Official receiving the tender or his duly authorized person shall open
the online.
For any further queries, bidders may kindly contact
For more details, please contact on working days within working hours (10:30 to 17:30)
Tel. No. 07582-266814, Mob. 9425477550
E-tendering Helpdesk at TCS, Bhopal Tel. No. 18002588684
E-mail:- [email protected]
FORMAT OF COVERING LETTER
Ref No: …………………………………….. Date: …………………………….
To,
The Joint Director
Skill Development, (ITI's)
Woman ITI Campus Khurai Road,
Sagar-470002
Sub: Submission of Supply of Tools & Equipment for ITIs of Sagar Zone, Tender SPN No. JDSD-
SGO/SP/TEN/2015-16/01
Dear Sir,
As per terms & conditions of the tender following documents are submitted as under:
1. Form “A” Enclosure No. …………………….
2. EMD
Tender No
Earnest Money Deposit
DD No Date Issuing Bank
01 INR 100000
3. Other Testimonials …………………
We have quoted rates for items (Number of quoted item to be mentioned) in the Tenders as stated
below:
Tender No
Total Item in Tender Enquiry
No of Item Quoted
01
The entire item is quoted with brand name & full specification. The technical detail as desired is
submitted in prescribed format as per enclosed Annexure
Authorized Signatory
Name & Signature with Seal
Date
Annexure-1
FORM – A
(To be signed and returned along with the tender)
Ref No: …………………………………….. Date: …………………………….
To,
The Joint Director
Skill Development, (ITI's)
Woman ITI Campus Khurai Road,
Sagar-470002
Sub: Submission of Supply of Tools & Equipment for ITIs of Sagar Zone, Tender SPN No. JDSD-
SGO/SP/TEN/2015-16/01
Dear Sir,
I/We
Name of Authorized Signatory
Name of Bidder
Address of Bidder
Phone
Have read the Tender rules for the supply of various goods as per Tender notice to the Industrial
Training Institutes in Sagar Zone and I/We accept all rules for Tender.
Authorized Signatory
Name & Signature with Seal
Date
Annexure - 2
MANUFACTURERS' AUTHORIZATION FORM
Ref No: …………………………………….. Date: …………………………….
To,
The Joint Director
Skill Development, (ITI's)
Woman ITI Campus Khurai Road,
Sagar-470002
Dear Sir,
We who are established and reputable manufacturers of (name and description of goods
offered) having factories at (address of factory) do hereby authorize M/s (Name and address of
Agent) to submit a bid, and sign the contract with you for the goods manufactured by us against the
Tender Published by you.
Yours faithfully
(Name)
(Name of manufacturers)
Note: This letter of authority should be on the letterhead of the manufacturer and should be
signed by a competent person. This AUTHORIZATION FORM should be notarized. It should be
attached in the bid.
Annexure – 3
PROFORMA FOR PERFORMANCE STATEMENT
(FOR THE PERIOD OF LAST TWO YEARS)
Tender SPN NO JDSD-SGO/SP/TEN/2015-16/01
Date of Opening
Name of Bidder
Name & Address of Purchaser
Order No & Date
Description & Quantity
of order item
Order Value
(in Rs)
Date of Delivery
Actual Delivery
Date
Reason of delay in delivery (if any)
Attach satisfaction Certificate issued by Purchaser
1 2 3 4 5 6 7 8
Authorized Signatory
Name & Signature with Seal
Date
Annexure - 4
(COMPLIANCE OF TENDER (AFFIDAVIT)
(To be submitted by the BIDDER on stamp paper duly notarized)
I/We, M/s. ___________________________________ represented by its Proprietor/Managing Partner / Managing Director having as Registered Office at _____________________________________andits factory premises at _____________________________________ do declare that I / We have carefully read all the conditions of Tender in Ref. No. __________________ for supply of Tools, Equipments and Machines floated byJoint Director, Skill Development (ITIs) – Sagar Zone, Woman ITI Campus Khurai Road, SAGAR – M.P, and accepts all terms and conditions of tender. I / We agree that the Deptt. forfeiting the Bid security and or Performance Security Deposit and debarring / black listing me / us for a period of 2 years , if any information furnished by us proved to befound false, misleading, malafide at any time or during the inspection and not complying the tenderconditions & specifications. I /We hereby declare that, we have not been debarred / penalized by any Govt. Departments/ neither Undertaking nor our marketing Assistance has been stopped / withdrawn in the past. We hereby extend our full guarantee and warrantee as per Terms & Conditions of the above tender for goods & services offered by us. We hereby declare that we will be held fully responsible for any mischief/misconduct or supply of substandard items by us or our dealer/distributor. We also confirm to provide the spares for at least five years from the date of supply / installation. We reiterate that goods ordered on the above firm shall be supplied in due time.
Seal Signature:
Name & address:
to be attested by the Notary:
Annexure-5
PRICE SCHEDULE (To be fill in prescribed Excel format only & same to be upload for Price Bid, should be submit Separate Sheet for each Tender)
Tender SPN NO JDSD-SGO/SP/TEN/2015-16/01
S.No Item
Code
Name &
Specification
of Item
Make Price for each unit (in Rs.)
Unit Price
Including
Excise/
Custom Duty
(if any)
Service
Tax (if
any)
Inland transportation,
insurance, Installation
and other local costs
incidental to delivery
Total price
inclusive of
a+b+c (Rs. in
figure)
Sales
Tax/VAT/CST
(if any)
Total Unit
priceinclusive
of all(Rs. in
figures)
Total unit price
inclusive of all (Rs.
in words)
(a) (b) (c) (a+b+c)=d (e) (d+e) (f)
Authorized Signatory
Name & Signature with Seal
Date
Annexure - 6
GUARANTEE CERTIFICATE
(On the original letter head of the manufacturer)
Ref No: …………………………………….. Date: …………………………….
To,
The Joint Director
Skill Development,
Woman ITI Campus Khurai Road,
Sagar-470002
Sub: Submission of Supply of Tools & Equipment for ITIs of Sagar Zone, Tender SPN No. JDSD-
SGO/SP/TEN/2015-16/01
Ref: Your S.O.NO. ……………… Dated: …………….placed on our Authorized Dealer
M/s ……………………………………………………………………………………………………………………………………….
Dear Sir,
With reference to the above, this is to certify that the following item has been supplied by
our Authorized Dealer M/s …………………………………………………………………………
SN Item Name & Description QTY
1
2
We further certify that the material supplied as above has been duly pre inspected by us and have
been found to be in conformity with specification as per the terms & conditions of the supply order.
They are hereby guaranteed for a period of 12 months from the date of receipt at respective ITI;
against any material defects, manufacturing defects (Including assembly installation, commissioning
as applicable) and bad workmanship.
In case of any defect, we guarantee to replace the same immediately without at any cost.
Seal & Signature of Dealer
Seal & Signature of Manufacturer
CC: Principal, Govt. ITI ……………………………………………..
Annexure-7
PERFORMANCE SECURITY FORM
To, …………………………………………………………………………………………
( Name of Purchaser )
WHEREAS
………………………………………………………………………………………………………………
………………………………………………………………
( Name of Supplier )
hereinafter called “ The Supplier” has undertaken , in pursuance of Contract No. ………………Dated
……………. 2016 … to supply (Description of Goods) hereinafter called “The contract.” AND
WHEREAS it has been stipulated by you in said contract. That the supplier shall furnish you with a Bank
Guarantee by a recognized bank for the sum specified there in as security for compliance with the
supplier’s performance obligations in accordance with the contract. AND WHEREAS We have by affirm
that we are Guarantors and responsible to you on behalf of the supplier, up to a total of ( Amount of the
Guarantee in Words and Figures ) and we undertake to pay you , upon Your first written demand
declaring the supplier to be in default under the contract and without cavil or agreement, any sum of sums
within the limits of ( Amount of Guarantee ) aforesaid , without Your needing to prove or to show grounds
or reasons for your demand or the sum specified there in.
This Guarantee is valid until the …………Day of ………………2016
Note- Stamp Paper of Bank Guarantee should be purchased by Bank.
Signature and seal of the Guarantors
( Bank Authorities )
…………………………………….........
………………………………………
………………………………………
Date …………………………….
Address ………………………….
…………………………………….
……………………………………..
Annexure - 8
CHECK LIST ENVELOPE – A
SN Documents Submitted
Y/N
Page No
1. Duly filled Checklist as per format given in Annexure – 8.
2. EMD in form Demand Draft of Nationalized Bank/Scheduled Bank in Favour of “Joint Director, Skill Development,(ITI's) Sagar”
3. Covering Letter duly signed & stamped on letter head.
4. Form – A duly signed & stamped on letter head
5. Self-attested copy firm registration Certificate
6. Self-attested copy of registration in Commercial/sales tax department and its TIN number.
7. Item Wise Authorization Certificate in case of Authorized Dealer Annexure – 2.
8. Latest Sales/VAT tax clearance certificate.
9. Latest Income Tax clearance certificate.
10.
Declaration of not having been debarred/blacklisted either by the Tender Inviting Authority or by any State Government or by Government of India on INR 100 Judicial Stamp. Compliance of Tender (affidavit) Duly Notarized as par Annexure – 4.
11. Audited Balance sheet and Profit and Loss Statement of last three financial years.
12. Annual turnover statement of last three financial year backed by practicing chartered accountant.
13.
Self-attested copy of relevant Licence for Manufacturing/Selling and distribution (whichever appropriate) of the product quoted duly approved by the Licensing authority for each schedule of product quoted as per specification in the tender.
14. No Deviation Certificate.Annexure – 9.
15. Catalogue of Items.
16. Performance statement as per the formatAnnexure – 3.
Authorized Signatory
Name & Signature with Seal
Date
Annexure-9
No Deviation Certificate
Tender No.- -----
S.No. Specification of
Machine/Equipment
mentioned in
Tender Enquiry
Specification of
Machine/Equipment
offered by the
Bidder
Whether there
are deviation
from the tender
specification
Yes/No
If yes,
indicate the
deviation &
whether it is
on +ve side &
how
Authorized Signatory
Name & Signature with Seal
Date
Annexure – 10
List of Items (01 Mechanical & Electrical Machine)
SN Item Code Item Name Specifications Indicative
QTY
1. WEL57 Power saw machine
14’’
Power hacksaw machine Power hacksaw machine
Cutting Capacity
( Round ) : 250
( Square ) : 200
( Flat ) : 250 X 75
Blade : 450
Motor H.P. (1440 RPM) : 1.5
' V ' Belt : B 56 X A 34
Floor Space : 500 X 1350
Height : 975
5
2. WEL41 Welding Transformer
or Invertors with all
accessories ( 300A ,
OCV 60 ± 100 V, 60%
duty cycle)
Welding Transformer or Invertors with all accessories ( 300A
, OCV 60 ± 100 V, 60% duty cycle) 2
3. FIT175 SS and SC centre lathe
(all geared) with
minimum specification
as: Centre height 150
mm and centre
distance 1000 mm
along with 3 & 4 jaw
chucks, auto feed
system, safety guard,
taper turning
attachment, motorized
coolant system,
lighting arrangement
& standard
accessories.
Capacity- : Height of centre 150mmCentre
distance 1200mmSwing over bed.
350mmSwing over cross slide 200mmSwing in gap
530mmWidth of gap 150mmWidth of bed
280mmHead stock- :Spindle nose standard A2-
5Spindle bore 42mmSpindle taper
METRICSpindle speeds nos . 16Speed range forward
30-1200RPM.Speed range reverse 30-1200RPMFeeds
& threads-:No. of longitudinal 40/0.06 to
2mm/rev feed / range 40/0.06 to
2mm/revNo. of cross feed / range 40/0.014-
0.44mm/revScrew of range1. Metric 40/0.5 to
10mm pitch 2. Inch. 40/2 TO 60 T.P.I.3.
Module 30/0.25 TO 3.254. D.P. 30/8
TO 120Tools or top slide -:Top slide travel
105mmCross slide travel 215mmLeast count
of graduation 0.2mm longOn hand wheels for carriage ,
0.5mm top slide Cross slide and top slide.Max. shank section
of tool 25 x 25mmTail stock-: Tail stock sleeve taper
MT- 3 Sleeve travel (manual) 140 mmSleeve
diameter 50 mm min.Graduation of sleeves
collar 1 div.= mmOffset on tail stock (max.) 5.0 mm
on either sideAcces.-:Independent chuck 300 mm , 3 jaw self –
centering chuck 250 mm , fixed steady , travelling steady
faceplate , driving plate , 4 way tool posts , quick change gear
box for metric or British threads, live & dead centers with
taper attachments all geared head stock type
2
4. FIT176 Drilling machine pillar
sensitive 0-20 mm cap
Drilling machine pillar sensitive 0-20 mm cap with swivel
table motorised with chuck & key. Precision Heavy Duty Pillar 1
SN Item Code Item Name Specifications Indicative
QTY
with swivel table
motorised with chuck
& key.
Drill Machine,Cap: 20 mm, Spindle traveling – 125 mm,with
standard accessoriesOptional:® Drill Vice® Drill Chuck,
Arbor® ISI electric motor, Switch and V belt
5. FIT177 Drilling machine bench
sensitive 0-12 mm cap
motorised with chuck
and key.
Drilling machine bench sensitive 0-12 mm cap motorised with
chuck and key.Sensative drilling machine pilliar type 12mm
Extra Accessories:
. ISI Make electric motor, Switch and V belt.
. Drill Vice
. Drill Chuck
Drill Bit set 3 mm to 12 mm set of 10 pcs.
7
6. FIT33 Portable hand drill
(Electric) 0 to 6 mm
Electrical drill portable machine
Drilling dia in wood : 15 mm
Drilling dia in steel : 6.5. mm
Power input : 350 w
No-load speed : 4000 rpm
Weight : 1 . 1 kgs
5
7. DM35/MMV
39
Car Jet washer with
standard accessories
Single plunger car washer with 3 HP moter and 12 mtr hose
and two guns, working pressure 25 Kgs, discharge per gun24
LPM
4
8. MMV42 Chain Pulley Block-3
ton capacity with
tripod stand
Chain Pulley Block (TRIPLE SPUR GEAR GRADE - 80) WITH 3
MTR CHAIN
CAPACITY 3 TON with tripod stand
2
9. MMV72 Disk brake with caliper
assembly
Disk brake with caliper assemblyThe Model is made out of
Orginal parts such as Two Brake disc, two Caliper assembly
(onesectioned), master cylinder etc, the model is mounted on
a sturdy iron frame and can bedemonstrated by operating the
lever provided.
4
10. MMV237 Drilling machine bench
to drill up to 12mm dia
along with accessories
Drilling machine bench to drill up to 12mm dia along with
accessories 1
11. FIT179 D.E. pedestal Grinding
machine with 200mm
diameter wheels rough
and smooth with twist
drill grinding
attachment.
PEDESTAL GRINDER
HP 1.0 KW 0.75 PH 3 HZ 50
AMP 1.6 VOLT 415 RPM 2800
Complete with Grinding Wheel
Size: 200 x 25mm x 19.05 mm ( Original bore 31.75 MM) ,
fitted with Eye Shield, Starter, Wheel Guard, And
WHEEL CENTRE DIST. : 460MM
CENTRE HEIGHT : 940MM
EXTRA :
DRILL GRINDING ATTACHMENT (UPTO 19MM)
3
12. DM191/MM
V241
Grinding machine
(general purpose) D.E.
pedestal with 300 mm
dia wheels rough and
PEDESTAL GRINDER DIRECT DRIVEN WITH INBUILT MOTOR
MOUNTED ON C.I. PEDESTAL STAND
HP 2.00 KW 1.5 PH 3 HZ 50
AMP 3.5 VOLT 415 RPM 1400
Complete with Grinding Wheel Size :300 X 50 X 31.75 mm
3
SN Item Code Item Name Specifications Indicative
QTY
smooth (Original bore 50.8 MM,)(One Coarse & one Medium)
Fitted with Eye Shield, Siemens Starter,
Wheel Guard, & Std Tool Rest Plate
WHEEL CENTRE DIST. : 615MM
CENTRE HEIGHT : 940MM
13. FIT ALL01 Transformer welding
set 150 amps. –
continuous welding
current, with all
accessories and
electrode holder
Transformer welding set 150 amps. – continuous welding
current, with all accessories and electrode holder 3
14. DM202/MM
V260
Welding Transformer (
150-300 Amps)
Welding Transformer ( 150-300 Amps) 5
15. DM166/MM
V199
Timing lighter Timing lighterFor checking and setting ignition timing on
automotive,agricultural and marine engines. Measures
ignition spark advance from 0-60ş. For use on 12V systems.
Reverse polarity protected. Accurate to 8,000rpm. 1m long
removable coiled power leads. Impact resistant metal case
and rubber nose cone. On/off trigger switch. Bright linear
Xenon flash tube for daylight use. Focused lens provides a
concentrated light. Easy to apply inductive impulse pick-up.
Built-in check light.
9
16. DM159/MM
V191
Tandem master
cylinder with booster
Tandem master cylinder with booster This model is made out
of original used parts, will be suitably sectioned to
demonstrate the internal construction details showing the
minute information and the model should be suitably painted
and mounted on a navopan wooden base.
12
17. DM169/MM
V207
Turbocharger cut
sectional view
Turbocharger cut sectional view This model is made out of
original used parts, will be suitably sectioned to demonstrate
the internal construction details showing the minute
information and the model will be suitably painted and
mounted on a navopan wooden base.
3
18. DM171 Universal puller for
removing pulleys,
bearings
Universal puller for removing pulleys, bearings 1
19. DM175/MM
V215
Valve spring
compressor universal.
Valve spring compressor universal. 5
20. DM174/MM
V214
Valve Lifter Valve Lifter 3
21. DM178/MM
V218
Water pump for
dismantling and
assembling
Water pump for dismantling and assembling 12
SN Item Code Item Name Specifications Indicative
QTY
22. DM182/MM
V231
Arbor press hand
operated 2 ton
capacity
Arbor press hand operated 2 ton capacity Overall Dimensions
(L x W xH) (In.) 18-1/8 x 10-1/4 x 22-1/2Weight (Lbs.)
108Capacity Over Table (In.) 11/12Anvil Diameter (In.) 6-
11/16 Arbor press hand operated 2 ton Arbour
Press Salient Features 1) Extra Heavy cast Frame Ribbed for
strength2) EN-8 Casehardened with Heavy duty rack teeth3)
Base Hole Adjustable with Bushings to Suit different jobs.* Set
for Dies * Sturdy Accurate and Reliable* Smooth Operation
and Precision WorkmanshipTECHNICAL SPECIFICATIONMax
Pressure exerted Ton 2Centre to Back mm 190Max. height
from Base to Guide mm 381Size of arbour round mm
44Approx. Weight of Press Kg 80Applications :1)
Embossing2) Punching3) Cutting4) Pressing5) Stamping6)
Deep Drawing etc.
3
23. DM183/MM
V232
Automotive exhaust 5
gas analyzer (petrol &
Diesel) or Diesel
Smoke meter
Automotive Exhaust 5 Gas Analyzer-Petrol
1. Measures CO,HC,CO2,O2
2. Engine RPM for Sealed engines
3. Oil Temperature measurement
4. Air Fuel Ratio and Lambda Measurements
5. Option to add Nox measurement facility
6. OMIL Class1 category
7. RS 232 Port
3
24. DM185/MM
V234
Diesel Engine – CRDI -
4 stroke for
Dismantling and
assembling with
swivelling stand
Diesel Engine – CRDI - 4 stroke for Dismantling and
assembling with swivelling stand Diesel Engine -The device
is designed based on latest technology diesel engines with
Common rail direct fuel injection system. The trainer helps to
simulate engine startup, speedup, slowdown and other actions
so as to illustrate the structure and working principle of CRDI
engines.Features 1. Real and operating CRDI Diesel engine,
illustrating the structure and working process.2. Coloured
circuit diagram on the training Module printed on to 6mm
organic glass base..3. Detection terminals for operator to
detect various sensors, actuators, electrical signals for engine
control unit, such as resistive, voltage, current , frequency and
wave form signals are provided on to the printed circuit
diagaram.4. Automobile meters are fitted on to the training
module along with the printed circuit diagram, to
demonstrate engine speed, temperature, fuel pressure,
charging light etc.,5. The training module is fitted with
diagnostic socket (DLC) for universal automobile
decoder(Scan tool) to read fault codes, clear fault codes and
read data stream.6. Fault setting switch bank will be provided
to induce faults in the training module to demonstrate the
fault and to diagnose faults. 7. Good working condition engine
will be provided with fuel tank and battery. Throttle control is
provided on the module to accelerate.8. The training module
is fabricated using steel pipe frame with spray painted for
good looks and the entire setup is provided with caster wheels
with brakes for easy movement of the same.
4
SN Item Code Item Name Specifications Indicative
QTY
25. DM186/MM
V235
Diesel engine (
Running condition )
Stationary type
Diesel engine (Running condition)stationary type
The Four stroke Diesel engine setup to be prepared by using
good working condition Single cylinder diesel engine with all
the fittings of the engine along with air filter, fuel tank
,electrical wiring etc., all mounted on to a sturdy iron frame.
3
26. DM203/MM
V263
Working Condition of
Diesel Engine – CRDI -
4 stroke Engine
Assembly with fault
simulation board
Working condition of diesel engine -CRDI-4 stroke engine
assembly with fault simulation board.The device is designed
based on latest technology diesel engines with Common rail
direct fuel injection system. The trainer helps to simulate
engine startup, speedup, slowdown and other actions so as to
illustrate the structure and working principle of CRDI
engines.Features 1. Real and operating CRDI Diesel engine,
illustrating the structure and working process.2. Coloured
circuit diagram on the training Module printed on to 6mm
organic glass base..3. Detection terminals for operator to
detect various sensors, actuators, electrical signals for engine
control unit, such as resistive, voltage, current , frequency and
wave form signals are provided on to the printed circuit
diagaram.4. Automobile meters are fitted on to the training
module along with the printed circuit diagram, to
demonstrate engine speed, temperature, fuel pressure,
charging light etc.,5. The training module is fitted with
diagnostic socket (DLC) for universal automobile
decoder(Scan tool) to read fault codes, clear fault codes and
read data stream.6. Fault setting switch bank will be provided
to induce faults in the training module to demonstrate the
fault and to diagnose faults. 7. Good working condition engine
will be provided with fuel tank and battery. Throttle control is
provided on the module to accelerate.8. The training module
is fabricated using steel pipe frame with spray painted for
good looks and the entire setup is provided with caster wheels
with brakes for easy movement of the same.
4
27. DM189/MM
V238
Dual Magnetization
Yoke : AC / HWDC, 230
VAC, 50Hz
Dual Magnetization Yoke : AC / HWDC, 230 VAC, 50Hz
Magnetic yoke along with Accessories;- a) Copper bulb - 1
nob) Pipe gauge - 1 noc) Manual - 1 no d) Calibration
certificatee) Carrying bagf) Test Bar
5
28. DM193(a)/
MMV244(a)
Hydraulic jack HI-LIFT
type -3 ton capacity
Hydraulic jack HI-LIFT type -3 ton capacity One stroke instant
lift foot pedal, raises the saddle up to jack point to increase
productivity. Constructed from heavy gauge steel. 1m, two
piece handle. 120mm diameter saddle.
Automatic safety overload protection. Positive twist, lock and
release mechanism. Heavy duty rear
swivelling castor wheels.
Maximum load: 3000kg.
Minimum height: 145mm.
Maximum height: 490mm.
3
29. DM193(b)/
MMV244(b)
Hydraulic jack HI-LIFT
type 5 Ton capacity
Hydraulic jack HI-LIFT type 5 Ton capacity
01. Capacity : 5 – Tones
02. Dist. Between Column (FB X LR) : 160 x 400 mm
3
SN Item Code Item Name Specifications Indicative
QTY
03. Dist. Between Ram to Bed (Min X Max) : 125 x 500 mm
04. Ram Stroke : 75 mm
06. Type Of Press Frame : ‘H’ frame type fabricated frame
30. DM194/MM
V245
Liquid penetrant
Inspection kit
Liquid penetrant Inspection kit SIZE - (in 280 ml pack) 4
31. DM196/MM
V249
Pipe Bending Machine
(Hydraulic type)
12mm to 30mm
Pipe Bending Machine (Hydraulic type) 12mm to 30mm 5
32. DM197/MM
V250
Pneumatic rivet gun
with standard
accessories
PNEUMATIC RIVET GUN WITH ACCESSORIESTOOL SHANK:
10.2 MM ROUNDPOWER: 7.2 JOULESBLOWS PER MINUTE:
3000 BPMBORE X STROKE: 19 X 67 MMWEIGHT: 1.6
KGLENGTH: 171 MMAIR INLET: ¼”TOOL TO BE SUPPLIED
IN A MOULDED CARRY CASE WITH 5 DIFFERENT TYPES OF
CHIELS, ONE MIMI OILER& ONE QUICK CHANGE RETAINER
8
33. DM199/MM
V252
Tin smiths bench
folder 600 x 1.6mm
Tin smiths bench folder 600 x 24 GAUGE 4
34. DM200/MM
V254
Trolley type portable
air compressor single
cylinder with 45 liters
capacity Air tank,
along with accessories
& with working
pressure 6.5 kg/sq cm
Trolley type portable air compressor 1 single cylinder with 45
liters capacity air tank all accessories and with working
pressure 6.5 kg/sq.cm2
TROLLEY TYPE COMPRESSOR 1 HP, SINGLE PHASE MOTOR
SINGLE STAGE WITH SINGLE PHASE MOTOR
Displacement : 128 LPM
C.F.M : 4.5 CFM
Motor Power Rating : 1 HP
Tank Capacity : 45 LTR
Max Pressure : 8.5Kg/ cm2/121psi
No Of Stage : SINGLE
No Of Cylinder : 1
Overall DIA(L*W*H) : 1230 x 390 x 780
2
35. WEL46 Air compressor
suitable for air plasma
cutting system.
Air compressor suitable for air plasma cutting system :
Compressuer Air pison type(Vehicular), 3HP, 3Phase C.G/ABB
moter-(2.2KW) Two stage with 3 phase moter
displacement:294 LPMCFM: 10.4 CFMMotor power rating:
3HP CG/ABBTan capacity: 90 ltrMax pressure:
12kg/cm2/171psiNo of stage: TWONo. of cylinder: 2Overall
Dia (LxWxH): 1230x445x810
6
36. DM201/MM
V259
Welding plant Oxy-
Acetylene complete (
high pressure)
Welding plant Oxy-Acetylene complete ( high pressure) 5
37. MMV20 AC alternator slip ring
puller
AC alternator slip ring puller 2
38. MMV23 Air Brake Assembly Air Brake Assembly
The model is made out of Original parts such as Air
compressor, Unloader valve, foot valve, Booster, Wheel
2
SN Item Code Item Name Specifications Indicative
QTY
assembly, air tank, control valve etc Suitably sectioned and
mounted on a sturdy
iron frame.
39. MMV183(a) Steering assembly -
.Rack & pinion,
Steering assembly - .Rack & pinion, 2
40. MMV183(b) Steering assembly -
Worm & roller
Steering assembly - Worm & roller 2
41. MMV183(c) Steering assembly -
Recirculating ball
Steering assembly - Recirculating ball 2
42. MMV183(d) Steering assembly -
Power steering
Steering assembly - Power steering 3
43. MMV31 Anti theft device Anti theft device 2
44. MMV41 Carburetor repair tool
kit
Carburetor repair tool kit 2
45. MMV50 Coil spring compressor
for suspension spring
Coil spring compressor for suspension springWeight: 5.65
lbsBolt Length (in): 11.25Bolt Material: Heat Tempered CR-
VCase Included: YesCoil Spring Compressor Type:
InternalDrive Size(s): 3/4Maximum Coil Wire Diameter (in):
0.75Maximum Sping Length (in): 12Maximum Spring Inside
Diameter (in): 5.5Minimum Spring Inside Diameter (in):
3.75Minimum Spring Length (in): 5Spring Compressor Detent
Pins: No
2
46. MMV53 Constant Mesh Gear
box with stand for
Dismantling and
assembly.
Constant Mesh Gear box with stand for Dismantling and
assembly
The Gearbox will be of original vehicle accessories, will be
mounted on stand, All the aggregates
will be cleaned and service and Painted with Single Colour
Paint
3
47. MMV58 Cut section working
model of automatic
transmission Gear box
Cut section working model of automatic transmission Gear
box The model is made out of full size original used automatic
transmission of a car, the transmission will be suitably
sectioned to show the internal details,of gear mechanism of
forward and reverse speeds. The automatic shifting of the
gears can be explained using this model clearly. The model
will be mounted on to a tubular frame, Suitable color
imported painting will be carried out along with Miracle
coating for the model will be done for extra gloss and shine.
The painting will be carried out in such a way that different
colors will be use for different components such as
identification of sectioned area etc according to the colors
code for easy identification of different systems and
mechanisms. All the hardware’s and gears will be suitably
electroplated. with appropriate stand and working manual.
2
SN Item Code Item Name Specifications Indicative
QTY
48. MMV189 Synchronous Gear box
with stand for
Dismantling and
assembly.
Synchronous Gear box with stand for Dismantling and
assembly
The Gearbox will be of original vehicle accessories, will be
mounted on stand, All the aggregates
will be cleaned and service and Painted with Single Colour
Paint
3
49. MMV55 Cut section Model of
Mock layout of a motor
car ±electrical system
working model
Cut section model of mock layout of a motor car -electrical
system working model cut section This demonstration board
which will give a complete idea of the electrical system of a
car. In this demonstration board the actual wiring with parts
and accessories of a car had been arranged, according to the
electrical circuit of a car and terminals are provided to
connect the battery. By giving connection the working of
individual parts such as Self starter, Alternator, Wiper Motor,
Horn, Head lights, Tail lamps, Parking lamps, Side indicators,
Brake light, Distributor, Sparks of spark plugs, etc., can be
demonstrated. The parts sectioned to show the internal
constructional details. This is a working demonstration model.
with appropriate stand and working manual.
2
50. MMV56 Cut section models of
shock absorbers
Cut section models of shock absorbers: This model is made
out of original used parts, will be suitably sectioned to
demonstrate the internal construction details showing the
minute information, the model will be suitably painted and
mounted on a navopan wooden base.
2
51. MMV57 Cut section of cross ply
and radial tyres
Cut section of cross ply and radial tyres: This model is made
out of original used parts, will be suitably sectioned to
demonstrate the internal construction details showing the
minute information, the model will be suitably painted and
mounted on a navopan wooden base
3
52. MMV59 Cut section working
model of centrifugal
clutch assembly.
Cut section working model of centrifugal clutch assembly.This
model is made out of original parts such as Flywheel, Clutch
plates, etc. to demonstrate the working of clutch assembly. By
operating the pedal provided the model can be demonstrated.
The entire model is mounted on a sturdy iron frame
2
53. MMV60 Cut section working
model of Diaphragm
clutch assembly.
Cut section working model of Diaphragm clutch assembly.
This model is made out of original parts such as Flywheel,
Pressure Plate ,Clutch plates, etc. to demonstrate the working
of clutch assembly. By operating the pedal provided the model
can be demonstrated. The entire model is mounted on a
sturdy iron frame
2
54. MMV61 Cut section working
model of Single plate
clutch assembly.
Cut section working model of Single plate clutch assembly.
This model is made out of original parts such as Flywheel,
Clutch plates, etc. to demonstrate the working of clutch
assembly. By operating the pedal provided the model can be
demonstrated. The entire model is mounted on a sturdy iron
frame
2
SN Item Code Item Name Specifications Indicative
QTY
55. MMV65/M
MV66
Demonstration board
of 2W Ignition system,
ignition coil
Demonstration board of 2W Ignition system, ignition coil
DEMONSTRATION BOARD OF IGNITION SYSTEM OF A TWO
WHEELER (WORKING): - This open demonstration-working
unit is made out of original used parts such as switch, ignition
coil, Magneto Assembly, spark plug, with necessary wiring
connections. By switching on the switch and by giving rotation
to the Magneto Assembly, Sequential Sparks in the spark plug
can be demonstrated.
5
56. MMV67 Demonstration board
of MPFI system
Demonstration board of MPFI system -The Instruction board
adopts the real components of electronic fuel injection system
to illustrate engine fuel system structure and working
principle. The components are rigged onto colour circuit
diagram. And made functional.Features1. Real and operatable
engine fuel injection system is assembled onto a colour
printed board to illustrating the structure and working
process .2. Coloured circuit diagram on the training Module
printed on to 6mm organic glass base. Where in the students
can compare the diagram and actual diagram.3. Detection
terminals for operator to detect various sensors, actuators,
electrical signals for engine control unit, such as resistive,
voltage, current , frequency and wave form signals are
provided on to the printed circuit diagram.4. The training
module is fitted with diagnostic socket (DLC) for universal
automobile decoder (Scan tool) to read fault codes, clear fault
codes and read data stream.5. Fault setting switch bank will
be provided to induce faults in the training module to
demonstrate the fault and to diagnose faults.6. Set the line
break, grounding short circuit, improper contact or open
circuit faults can be induced, user can adjust the number and
type of faults. 7. Good working condition Parts will be
provided with fuel tank. The instruction board has to be
connected to 220V AC socket Which changes to 12V DC
internally so that the board works without battery.8. The
training module is fabricated using steel pipe frame with
spray painted for good looks and the entire setup is provided
with caster wheels with brakes for easy movement of the
same.
2
57. MMV73(a) Distributor ±Duel
advance type
Distributor ±Duel advance type 2
58. MMV73(b) Distributor reluctance
type
Distributor reluctance type 2
59. MMV78 Drum brake assembly Drum brake assembly- This model is out of original parts such
as Two Brake drum assembly , one master cylinder wheel
cylinder (One sectioned), Brake Shoes , etc. the model can be
demonstrated by operating the lever provided .
2
60. MMV212 Vacuum assisted
hydraulics brake
assembly with vacuum
Vacuum assisted hydraulics brake assembly with vacuum
booster 3
SN Item Code Item Name Specifications Indicative
QTY
booster
61. MMV98 Full floating axle and
semi-floating axle
assembly
Full floating axle and semi-floating axle assembly
This model is made out of original used heavy vehicle parts,
suitably sectioned to show clearly the action of Differential
gear box, such as pinion crown wheel in Differential and Brake
drums in Rear axle, A Crank handle is provided to
demonstrate the model. The model is mounted on a sturdy
iron frame. & This model is made out of original used light
vehicle, suitably sectioned to show the action of Differential
gear box and Brake drums in Rear axle. A Crank handle is
provided to demonstrate the model. The whole model is
mounted on a sturdy iron frame.
2
62. MMV157 Rear axle full floating
type with stand for
Dismantling and
assembly
Rear axle with stand for Dismantling and assembly
The axle will be of original vehicle accessories, will be
mounted on to stand, All the aggregates will be cleaned and
service and Painted with Single Colour Paint
2
63. MMV93 Front axle ( Rzeeppa
Joint) with stand for
Dismantling and
assembly
Front axle ( Rzeeppa Joint) with stand for Dismantling and
assembly The Axle will be of original vehicle accessories, will
be mounted on stand, All the aggregates will be cleaned and
service and Painted with Single Colour Paint
2
64. MMV118 Horn and Horn relay Horn and Horn relay 4
65. MMV179(a) Starter motor axial
type
Starter motor axial type,The Starter Motor will be of original
vehicle accessories, will be mounted on base, All the
aggregates will be cleaned and service and Painted with Single
Colour Paint
2
66. MMV179(b) Starter motor pre-
engagement type
Starter motor pre-engagement type The Starter Motor will be
of original vehicle accessories, will be mounted on base, All
the aggregates will be cleaned and service and Painted with
Single Colour Paint
2
67. MMV179(c) Starter motor Co-axial
type
Starter motor Co-axial type The Starter Motor will be of
original vehicle accessories, will be mounted on base, All the
aggregates will be cleaned and service and Painted with Single
Colour Paint
2
68. MMV203 Tread wear indicator Tread wear indicator 2
69. MMV255 Tube/ tyre vulcanizing
machine
Tube/ tyre vulcanizing machine 2
70. MMV206 Tubeless tyre repair
kit
Tubeless tyre repair kit 3
71. MMV208 Tyre & split rim wheel
assembly
Tyre & split rim wheel assembly 2
SN Item Code Item Name Specifications Indicative
QTY
72. MMV219 Wheel cylinder Wheel cylinder 8
73. MMV220 Wiper motor assembly Wiper motor assembly 4
74. MMV223 Working Model of
power windows
Working Model of power windows
This model to be made out of parts, will be suitably sectioned
And Arranged to demonstrate the internal construction
details showing the minute information such as motor and its
gear arrangement etc., and working of the same can be show
by connecting it to a battery, the model will be suitably
painted and The entire model is mounted on a sturdy iron
frame
2
75. MMV224 Working model of
torque converter
Working model of torque converter
This model should be made out of parts, should be suitably
sectioned to demonstrate the internal construction details
showing the minute information, and working of the same, the
model should be suitably painted and mounted on a navopan
wooden base.
2
76. MMV225 4 Point relays 4 Point relays 4
77. MMV226 5 Point relays 5 Point relays 4
78. MMV227 Air bag simulator Air bag simulator The Instruction board adopts the real
components of Air bag system to illustrate Air bag safety
system structure and working principle. The components are
rigged onto colour circuit diagram and made
functional.Features1. Real and operatable Air bag system is
assembled onto a colour printed board to illustrating the
structure and working process .2. The Vehicle Crash is
Simulated by pushing and hitting the crash sensor along the
rail provided to demonstrate the quick air bag inflation.3.
Coloured circuit diagram on the training Module printed on to
6mm organic glass base. Where in the students can compare
the diagram and actual diagram.4. Detection terminals for
operator to detect various sensors, actuators, electrical
signals for engine control unit, such as resistive, voltage,
current , frequency and wave form signals are provided on to
the printed circuit diagram.5. Fault setting switch bank will be
provided to induce faults in the training module to
demonstrate the fault and to diagnose faults. 6. Set the line
break, grounding short circuit, improper contact or open
circuit faults can be induced, user can adjust the number and
type of faults.7. Good working condition Parts will be
provided with fuel tank. The instruction board has to be
connected to 220V AC socket Which changes to 12V DC
internally, so that the board works without battery.8. The
training module is fabricated using steel pipe frame with
spray painted for good looks and the entire setup is provided
with caster wheels with brakes for easy movement of the
2
SN Item Code Item Name Specifications Indicative
QTY
same.
79. MMV229 Air conditioning
service Unit (Car)
Air conditioning service Unit (Car)
1.Functions: vacuum,recharging,refrigerant purifying and
recycling,
2.Discharge used oil and refill new oil
3.High pressure and low pressure alarm
4.Empty tank alarm
2
80. MMV230 Air conditioning
trainer kit
Air conditioning trainer kit This model is made out of original
New parts, will be suitably Arranged on to a Metal frame with
navopan board to demonstrate details of Piping connection,
Wiring circuit with all the accessories such as Cooling Coil,
compressor, evaporator, necessary hoses, condenser etc., the
model will be made to work using a FHP motor so that by
operating the AC panel the operation and cooling effect of the
same can be demonstrated, the Model will contain a car
Battery for the operation of the blower and Magnetic clutch
the entire system will be suitably painted.
2
81. MMV239 Four stroke petrol
engine with CNG
setup-working
condition
Four stroke petrol engine with CNG/LPG setup-working
condition The Four stroke petrol engine setup should be
prepared by using good working condition multi cylinder car
engine with all the fittings of the engine along with radiator,
silencer, air filter, starter, battery, alternator, indication
meters, fuel tank ,electrical wiring with ignition switch etc., all
mounted on to a sturdy iron frame with caster wheels (mobile
trolley) . All the fittings such as meter, fuel tank, radiator etc.,
along with the engine should be arrange on to the paint
finished trolley with its original fittings such as rubber
dampers and clamps so as to contain the vibrations. The
wiring for the sensors, indication meters etc, should be done
so that by cranking the ignition the engine should start
working, the indications such as alternator charging, oil
pressure, temperature etc., should be displayed on to the
necessary indication meter attached. The engine assembly
should be serviced ,painted with a single colour paint.
3
82. MMV242 Hand operated
Hydraulic press
HYDRAULIC H - FRAME PRESS (Hand Operated)
01. Capacity : 5 – Tones
02. Dist. Between Column (FB X LR) : 160 x 400 mm
03. Dist. Between Ram to Bed (Min X Max) : 125 x 500 mm
04. Ram Stroke : 75 mm
06. Type Of Press Frame : ‘H’ frame type fabricated frame
2
83. MMV246 MPFI petrol engine
with swiveling stand
along with special
tools for dismantling
and assembling
MPFI petrol engine with swiveling stand along with special
tools for dismantling and assembling
The original car engine will be mounted on to the rolling
stand, so that slowly rolling the handle provided the engine
can be rotated and lock and any position and angle to enable
the students to assemble or dismantle the engine, a large oil
drip pan is provided at the bottom to collect the small screws,
parts and oil dripping. The rotating stand is made out of steel
tube with gears for slow speed operation along with self
2
SN Item Code Item Name Specifications Indicative
QTY
retention wheels. The Paint finished rotating stand is
provided with heavy duty caster wheels with brakes.
84. MMV248 Petrol Engine(2-
stroke) Motor
Cycle/Scooter along
with special tools and
accessories
Petrol Engine vertical ( 2 stroke) Motor cycle /
Scooter type 1.5 hp Indian make contemporary model
The petrol engine setup to be prepared by using good working
condition engine with all the fittings of the engine along with
silencer, air filter, fuel tank ,electrical wiring with ignition
switch etc., all mounted on to a sturdy iron frame with caster
wheels (mobile trolley) . All the fittings such as fuel tank, etc.,
along with the engine should be arrange on to the paint
finished trolley with its original fittings such as rubber
dampers and clamps so as to contain the vibrations.. The
engine assembly should be serviced ,painted with a single
colour paint.
1
85. MMV253 Transfer case with
stand for Dismantling
and assembly.
Transfer Case with stand for Dismantling and assembly - The
Axle will be of original vehicle accessories, will be mounted
on stand, All the aggregates will be cleaned and service and
Painted with Single Colour Paint
3
86. MMV256 Two post car lift –
capacity 4000 kg
Electro Mechanical Two Post Lift 3.2 Tons Lifting Capacity
Electro MechanicalUniversal adaptor Input voltage : 380 V, 4
HP
3
87. MMV257 Tyer Changer Machine Tyer Changer Machine--External Locking Rim Dimensions:
300mm-510mm (12″- 20″), Internal Locking Rim Dimensions:
355mm-585mm (14″- 23″), Max Tyre Diameter: 950mm
(37″),Max Tyre Width: 410mm (16″),Bead Breaker Force
(10bar) : 2500Kg, Working Pressure: 8-10bar(116-145Psi),
Power Supply Voltage: 220V (Single Phase)
Internal locking rim dimensions: 355mm-585mm (14"-23")
Max tyre diameter: 950mm (37"),
Max tyre width: 410mm (16"),
Bead breaker force (10bar) : 2500kg,
Working pressure : 8-10bar(116-145psi),
Power supply voltage : 220V (single phase)
2
88. MMV258 Ultrasonic Injection
cleaning equipment
INJECTOR CLEANER & TESTER which can clean and test Auto
engine injectors by simulating engine working conditions. It
can also perform cleaning on the injectors and fuel supply
system on vehicle.
Specifications: Power supply: □AC220V±10%, 50Hz
Main unit power: 200W;
Ultrasonic cleaner power: 100W;
Simulated RPM range: 10~9990rpm; step: 10rpm;
Time range: 1~9999s;
Pulse width: 0.5~25ms; step 0.1 ms;
Fuel tank capacity: 4000ml;
Dimensions: 400mm×410mm×580mm
Feature - * Ultrasonic cleaning: To perform simultaneous
cleaning on several injectors, to remove the carbon deposits
2
SN Item Code Item Name Specifications Indicative
QTY
on the injector completely. * Uniformity/Spray ability test: To
test the uniformity of injecting amount of each injector, and to
monitor the spraying
status of each injector with the lighting of backlight. This test
is also for reverse flush.
* Leakage test: To test the sealing and dribbling conditions of
injectors under system pressure. * Injecting flow test: To
check the injecting amount of the injector in 15 seconds of
constant injection. * Auto. test: To test injectors by simulating
different working conditions. * On-vehicle cleaning: The unit
is equipped with various adaptors and couplers that facilitate
cleaning on the injectors on vehicle.
89. MMV261 Wheel alignment
Machine –
computerised 3D
Computerised 3 D Wheel aligner High Precision Dual Camera
Waterproof Targets Real time data reading 10"-24" Solid
Wheel clamps
2
90. MMV262 Wheel balancing
machine
Computerised digital Wheel Balancer with elevated display
panel, automatic Distance Measurement, steel wheel and 7
types of ALU function for rim dia upto 24",supplied along with
Wheel Guard, Mid Centring device & standard Cones
2
91. MMV264 Working Condition of
Petrol MPFI Engine
Assembly with fault
simulation board
Petrol MPFI Engine Assembly with fault simulation board:
Working of Petrol MPFI Engine Assembly with fault
simulation board The device is designed based on latest
technology petrol engines with Multi point fuel injection
system. The trainer helps to simulate engine startup, speedup,
slowdown and other actions so as to illustrate the structure
and working principle of MPFI engines.
Features
1. Real and operating Petrol MPFI engine, illustrating the
structure and working process.
2. Coloured circuit diagram on the training Module printed on
to 6mm organic glass base..
3. Detection terminals for operator to detect various sensors,
actuators, electrical signals for engine control unit, such as
resistive, voltage, current , frequency and wave form signals
are provided on to the printed circuit diagram.
4. Automobile meters are fitted on to the training module
along with the printed circuit diagram, to demonstrate engine
speed, temperature, fuel pressure, charging light etc.,
5. The training module is fitted with diagnostic socket (DLC)
for universal automobile decoder(Scan tool) to read fault
codes, clear fault codes and read data stream.
6. Fault setting switch bank will be provided to induce faults
in the training module to demonstrate the fault and to
diagnose faults.
7. Good working condition engine will be provided with fuel
tank and battery. Throttle control is provided on the module
to accelerate.
8. The training module is fabricated using steel pipe frame
with spray painted for good looks and the entire setup is
provided with caster wheels with brakes for easy movement
2
SN Item Code Item Name Specifications Indicative
QTY
of the same.
92. DM199/M
MV253
Discrete Component
Trainer / Basic
Electronics Trainer
Discrete Component Trainer / Basic Electronics Trainer -
Technical Specifications :Inbuilt Variable / Fixed DC Regulated
Power SuppliesOutput voltages : 0-3VDC: 0-30VDC:
+5VDCInbuilt AC Power SuppliesOutput voltages : 10 - 0 -
10VAC/ 500mAGlass Epoxt PCB used as front panel of 270
mm x 170 mm & mounted onlight weight shock proof plastic
cabinetSymbol diagram printed on Glass Epoxt PCB & all
important test Points arebrought out on front panelPower
requirement : 230 VAC 10%, 50Hz.Weight : 2.2 Kg
Approx.Dimensions (mm) : 300( L) x 175(B) x 75(H) List of
Experiments under above Topics : PN Junction Diode V-I
Characteristics Zener Diode V-I Characteristics Voltage
Stabilization of Zener Diode LED Characteristics Resistance in
Series & ParallelCharging & Dischrging of Condensor LCR
Resosnace Circuit Clipping & Clamping Half Wave, Full Wave
& Bridge Rectifier Common Base Transistor Amplifier
Common Emitter Transistor Amplifier Common Collector
Transistor Amplifier RC Coupled Amplifier Basic Logic
GatesRC Passive Filter Circuits Standard Accessories : Power
cable, Patch Chord & Instruction manual
5
93. DM29/MM
V33
Auto Electrical test
bench
1. Motor 2 hp three phase 1500rpm 2. Digital dc voltmeter of
3.5 digital display with minimum readable upto 0.1 volt 3.
Digital dc ammeter for load of 3.5 digit display with minimum
readable upto 1 amp.4. Digital rpm indicator 0-5000 rpm.5.
Speed sensor for sensing starter speed6. Alternator loading
through wire wound resistors of 0-50 amps capacity 5.
Alternator loading through 4nos rotary switches.6. Two
directional rugged mounting arrangement to suit various
range of alternators.7 Provision for two speed check with two
set of pulley and belts8 Starter free spin testing up to 100
amps capacity.9 110 v series lamp test facility also available.1.
Motor 2 hp three phase 1500rpm 2. Digital dc voltmeter of
3.5 digital display with minimum readable upto 0.1 volt 3.
Digital dc ammeter for load of 3.5 digit display with minimum
readable upto 1 amp.4. Digital rpm indicator 0-5000 rpm.5.
Speed sensor for sensing starter speed6. Alternator loading
through wire wound resistors of 0-50 amps capacity 5.
Alternator loading through 4nos rotary switches.6. Two
directional rugged mounting arrangement to suit various
range of alternators.7 Provision for two speed check with two
set of pulley and belts8 Starter free spin testing up to 100
amps capacity.9 110 v series lamp test facility also available.
4
94. ELE107/D
M30/MMV
34
Battery Charger Battery Charger : The Automatic Battery Chargers are
designed for precise charging of lead acid, sealed maintenance
free, VRLA (valve regulated lead acid) and other batteries.
These batteries require a sophisticated charger to charge
them in a precisely regulated fashion specified by the
manufacturer to avoid irreversible damage through gassing
and shortened service life. The Elak Automatic charger meets
the charging specifications of a wide range of VRLA and RG
11
SN Item Code Item Name Specifications Indicative
QTY
sealed batteries very accurately. The charger delivers a
measured constant current to the battery until the
manufacturer’s specified maximum battery voltage is attained.
This voltage is then held constant for a specified period to
allow a uniform charge across all the plates. The charger may
be left connected indefinitely to a fully charged battery
without the fear of over-charging or damage.SPECIFICATIONS
-
Voltage - 12 V/ 24 V /
Current 0 -15 A/ 0 -10 A /
End Voltage13.8 V / 14.4 V/ 27.6 V / 28.8 V Size
L x W x H (mm) 340 x 260 x 160 11
95. ELE111 Voltage Stabiliser Voltage Stabiliser- Input: 150 – 230 volt AC, Output: 220 volt
AC
3
96. ELE133(a) Starters for 2 to 5 H.P.
A.C Motors
a. Resistance type
starter
Starters for 2 to 5 H.P. A.C Motors Resistance type- Features:
Slipring Motor Starting by varying resistance through control
knob, Motor full speed run on all resistance cut with interlock
protection, Operated through push button and contactors,
Green Red indicators for Start & Stop the Motor. Dully marked
terminals for Rotar & Stators. Meetring
3
97. ELE133(b) Starters for 2 to 5 H.P.
A.C Motors
b. Direct on line
Starter
Starters for 2 to 5 H.P. A.C Motors
b. Direct on line Starter 2
98. ELE133(c) Starters for 2 to 5 H.P.
A.C Motorsc. Star Delta
Starter- manual, semi-
automatic and
automatic
Starters for 2 to 5 H.P. A.C Motorsc. Star Delta Starter- manual,
semi-automatic and automatic 2
99. ELE82(a) A.C. Energy Meter,
Single phase 5 amp
A.C. Energy Meter, Single phase 5 amp 1
100. DM121/
MMV151/E
LE28
Portable electric drill
Machine
Electrical drill portable machine
Drilling dia in wood : 15 mm
Drilling dia in steel : 6.5. mm
Power input : 350 w
No-load speed : 4000 rpm
Weight : 1 . 1 kgs
7
101. MMV99 Functional/experimen
t model of different
type of sensors.
Functional/experiment model of different type latest sensors.
1.Eletronic Contro Unit(ECU).
2.Crank shaft speed sensors.
3.Cam shaft Speed sensors.
4.Knock Sensors.
5.Mass Airflowsensor(MAF).
6.Oxygen sensor.
7.Manifold Absolute Pressure(MAP)sensor.
8.Throttle position sensor.
3
SN Item Code Item Name Specifications Indicative
QTY
9.Coolant Temperature sensor.
10.Manifold Air Temperature (MAT) sensor.
11.Exhaust Oxygen Sensor.
12.Distributor Refence Pules sensor.
13.Vehicle speed sensor.
14. Battery voltage sensor.
One Each Set of 14Nos.
102. ELE73(a) Ohm Meter Series
Type
Ohm Meter Series Type 7
103. ELE73(b) Ohm Meter Shunt Type Ohm Meter Shunt Type 7
104. DM49/
MMV64
DC Ohmmeter 0 to 300
Ohms, mid scales at 20
Ohms
DC Ohmmeter 0 to 300 Ohms, mid scales at 20 Ohms 8
105. ELE74 Multi Meter (analog) 0
to 1000 M Ohms, 2.5 to
500 V
Multi Meter (analog) 0 to 1000 M Ohms, 2.5 to 500 V 6
106. DM102/
MMV130
Multimeter digital Multimeter digital 10
107. cop17 Digital Multimeters,
3.5 digit handheld
type.
Digital Multimeters, 3.5 digit handheld type. 56
108. ELE76 A.C. Voltmeter M.I. 0 –
500V A.C
A.C. Voltmeter M.I. 0 –500V A.C 1
109. ELE77 Milli Voltmeter centre
zero 100 – 0 – 100 m
volt
Milli Voltmeter centre zero 100 – 0 – 100 m volt 2
110. ELE78 D.C. Milli ammeter 0 -
500m A
D.C. Milli ammeter 0 -500m A 1
111. ELE79(a) Ammeter MC 0-5 A Ammeter MC 0-5 A 2
112. ELE79(b) Ammeter MC 0- 25 A Ammeter MC 0- 25 A 1
113. ELE80(a) A.C. Ammeter M.I. 0-5A A.C. Ammeter M.I. 0-5A 3
114. ELE80(b) A.C. Ammeter M.I. 0-25
A
A.C. Ammeter M.I. 0-25 A 1
115. DM25/
MMV28
Ammeter 300A/ 60A
DC with external shunt
Ammeter 300A/ 60A DC with external shunt 16
116. ELE81 Kilo Wattmeter 0-1-3 Kilo Wattmeter 0-1-3 kw 3
SN Item Code Item Name Specifications Indicative
QTY
kw
117. ELE82(b) A.C. Energy Meter
Three Phase 15 amp
A.C. Energy Meter Three Phase 15 amp 4
118. ELE83 Power Factor Meter Power Factor Meter 2
119. ELE84 Frequency Meter Frequency Meter 4
120. ELE85 Flux meter Flux meter 3
121. ELE86 Wheat Stone Bridge
with galvanometer and
battery
Portable Wheatstone Bridge
designed to provide an accurate and sensitive measurement of
resistance and Locating faults in cables by adopting the
Murray and Varley Loop circuit for tests,
• Range: 0.001 ohms to 11.11 megohms.
• Constantan coil, accuracy :t 0.1 %
Galvanometer
DC mounted in beautiful Bakelite/acrylic stand with Accuracy
+2.0% F.S.D. with Lock type terminals packed in card box.
Ranges available 30-0-30, 50-0-50.
• Size M065 Top Terminals
• MR80 Deluxe Model
• MR100 (80X100) Rectangular
1
122. MMV34 Battery –charger Battery Charger : The Automatic Battery Chargers are
designed for precise charging of lead acid, sealed maintenance
free, VRLA (valve regulated lead acid) and other batteries.
These batteries require a sophisticated charger to charge
them in a precisely regulated fashion specified by the
manufacturer to avoid irreversible damage through gassing
and shortened service life. The Elak Automatic charger meets
the charging specifications of a wide range of VRLA and RG
sealed batteries very accurately. The charger delivers a
measured constant current to the battery until the
manufacturer’s specified maximum battery voltage is attained.
This voltage is then held constant for a specified period to
allow a uniform charge across all the plates. The charger may
be left connected indefinitely to a fully charged battery
without the fear of over-charging or damage.SPECIFICATIONS
- Voltage - 12 V/ 24 V / Current 0 -15 A/ 0 -10 A / End
Voltage13.8 V / 14.4 V/ 27.6 V / 28.8 V SizeL x W x H (mm)
340 x 260 x 160 11 5
123. ELE112 3- point D.C. Starter 3-point DC Starter.
3 Point D.C. Motor starter suitable to work on 5 H.P. D.C.
motor, Voltage 230/250 with a maximum 15% full load
current the starting period does not exceed 30 seconds with
under voltage and an intensions (Magnetic) over load release
device.
1
124. ELE113 4- point D.C. Starter 4-point DC Starter :-4 Point D.C. Motor starter suitable to work
on 5 H.P. D.C. motor, Voltage 230/250 with a maximum 15% 1
SN Item Code Item Name Specifications Indicative
QTY
full load current the starting period does not exceed 30
seconds with under voltage and an intensions (Magnetic) over
load release device
125. ELE90 1 Phase Variable Auto
Transformer
2 Phase Variable Auto Transformer 1
126. ELE98 Current Transformer
415 Volt,50 Hz, CT
Ratio 150 / 5 Amp,
5VA
Current Transformer 415 Volt,50 Hz, CT Ratio 150 / 5 Amp,
5VA 1
127. ELE99 Potential Transformer
: 415 Volt,50Hz, PT
Ratio 11KV/ 110V,
10VA
Potential Transformer : 415 Volt,50Hz, PT Ratio 11KV/ 110V,
10VA 1
128. ELE123 Single phase
Transformer, core
type, air cooled 1 KVA ,
240/415 V, 50 Hz
Single phase Transformer, core type, air cooled
2KVA. 230/115V with tapping on secondary
1
129. ELE133(d) Auto Transformer type Auto Transformer type 3
130. DM202/
MMV260
Welding Transformer (
150-300 Amps)
Transformer welding set 150 amps. – continuous welding
current, with all accessories and electrode holder. step down
transformer main supply 220-440 V necessity 100-1000amp
5
Joint Director
Skill Development Sagar