GMS1250C / GMS1250CS
Features:
EC Series
M: Mechanical speed governor, E/ECU: Electronic speed governor;NA: Naturally aspirated, TC: Turbocharged, TCA: Turbocharged and air-air aftercooled. TCW: Water-cooled Turbocharged;The weights are approximate and without fuel.
Also available in the following voltages: 415/240V-380/220V-220/127V-200/115V; ESP: Standby Power Standby duty, operation under variable load, without over load;PRP: Prime Power-Continuous duty operation, under variable load 24/24h-10% over load permissible 1 hour/12 hours;The data is only for your reference but not for use of sales.
Ratings at 0.8 power factor.
Generating Set Model Prime Standby
GMS1250C/S 1250kVA/1000kW 1375kVA/1100kW
Output Ratings
Ratings and Performance Data Dimensions and Weights
• Excitation system: self-excited (AREP and PMG are optional)
• ATS (automatic transfer switch) receptacle
• Lockable battery isolator switch
• Stainless galvanized zinc plates with strong
corrosion resistance
• Vibration isolators between the engine/alternator
and base frame
• Integrated wiring design
• Base fuel tank for at least 8 hours running
• Equipped with an industrial muffler
• Engine oil pump
• 50℃ radiator
• Top lifting and steel base frame with forklift holes
• Drainage for fuel tank
• Complete protection functions and safety labels
• IP54 (soundproof sets), IP56 (control system)
• Water jacket preheater, oil heater and double air
cleaner, etc. are available.
Prime
Standby
Structure Type:
Fuel Tank Capacity: L
(100% Load)Fuel Consumption: l/hr
GMS1250C
GMS1250CS
GMS1250C
GMS1250CS
Engine Make & Model:
Alternator Model:
Alternator Brand:
Control System:
Noise Level@7m:
Frequency & Phase:
Engine Speed: RPM
KTA50-G3
LVI634G
STAMFORD
PLC-8610 / PLC-7420
75.7-85.6
50Hz & 3PH
1500
A
C
/
1500
274
293
Dry = With Lube Oil Wet = With Lube Oil and Coolant
Length (L)mm (in)
Width (W)mm (in)
Height (H)mm (in)
Drykg (lb)
GeneratingSet Model
GMS1250C
GMS1250CS
5280 2200 2480 10800
6058 2438 2795 15310
utput Ratings
Engine model: KTA50-G3
GMS1250C / GMS1250CSEC Series
GENERAL ENGINE DATAType................................................................................................................................................................ 4-Cycle; 60° Vee; 12-Cylinder DieselAspiration........................................................................................................................................................ Turbocharged and Aftercooled
Bore x Stroke ..............................................................................................................— mm x mm (in x in) 159 x 159 (6.25 x 6.25)Displacement ..............................................................................................................................— litre (in3) 2300 (37.8)Compression Ratio........................................................................................................................................ 13.9 : 1
Dry WeightFan to Flywheel Engine ........................................................................................................ — kg (lb) 4300 (9482)
Wet WeightFan to Flywheel Engine......................................................................................................... — kg (lb) 4536 (10002)
Moment of Inertia of Rotating Components • with FW 6001 Flywheel ........................................................................................... — kg • m2 (lbm • ft2) 10.4 (248) • with FW 6011 Flywheel............................................................................................ — kg • m2 (lbm • ft2) 20.8 (493)Center of Gravity from Front Face of Block............................................................................... — mm (in) 980 (38.6)Center of Gravity Above Crankshaft Centerline........................................................................ — mm (in) 279 (11)Maximum Static Loading at Rear Main Bearing......................................................................... — kg (lb) 908 (2000)
ENGINE MOUNTINGMaximum Bending Moment at Rear Face of Block.......................................................... — N • m (lb • ft) 6100 (4500)
EXHAUST SYSTEMMaximum Back Pressure at 1500 RPM (Standby Power)........................................... — mm Hg (in Hg) 76 (3)
AIR INDUCTION SYSTEMMaximum Intake Air Restriction • with Dirty Filter Element ................................................................................................. — kPa (in H2O) 6.2 (25) • with Clean Filter Element............................................................................................... — kPa (in H2O) 3.7 (15)
COOLING SYSTEM Coolant Capacity — Engine only .................................................................................... — litre (US gal) 124 (32.7)
— with HX 6076 Heat Exchanger ..................................................... — litre (US gal) 199 (52.7)Minimum Pressure Cap (for Cooling Systems with less than 2m [6 ft.] Static Head)........... — kPa (psi) 69 (10)Maximum Static Head of Coolant Above Engine Crank Centerline........................................... — m (ft) 18.3 (60)Thermostat (Modulating) Range ...............................................................................................— °C (°F) .. 82-93 (180-200)Maximum Coolant Friction Head External to Engine — 1500 rpm ....................................... — kPa (psi) 48 (7)Maximum Top Tank Temperature for Standby...........................................................................— °C (°F) 104 (220)Maximum Raw Water Flow @ 90 F to HX6076 Heat Exchanger.......................... — liter/min (US gpm) 409 (108)Maximum Raw Water Inlet Pressure at HX 6076 Heat Exchanger ...................................... — kPa (psi) 345 (50)
LUBRICATION SYSTEMOil Pressure @ Idle Speed..................................................................................................... — kPa (psi) 138 (20)
@ Governed Speed.......................................................................................... — kPa (psi) 310-448 (45-65)Maximum Oil Temperature ......................................................................................................... — °C (°F) 121 (250)Oil Capacity with OP6023 Oil Pan: Low - High................................................................. — litre (US gal) 114-87 (30-23)Total System Capacity (with Combo Filter)....................................................................... — litre (US gal) 135 (35.7)
Engine model: KTA50-G3
GMS1250C / GMS1250CSEC Series
ELECTRICAL SYSTEMCranking Motor (Heavy Duty, Positive Engagement) ........................................................................................................ — volt 24Battery Charging System, Negative Ground ............................................................................................................... — ampere 35Maximum Allowable Resistance of Cranking Circuit......................................................................................................... — ohm 0.002Minimum Recommended Battery Capacity
• Cold Soak @ 50 °F (10 °C) and Above ............................................................................................................. — 0°F CCA 1280• Cold Soak @ 32 °F to 50 °F (0 °C to 10 °C)...................................................................................................... — 0°F CCA 1800• Cold Soak @ 0 °F to 32 °F (-18 °C to 0 °C)....................................................................................................... — 0°F CCA 1800
COLD START CAPABILITYMinimum Ambient Temperature for Aided (with Coolant Heater) Cold Start within 10 seconds................................ — °F (°C) 50 (10)Minimum Ambient Temperature for Unaided Cold Start............................................................................................... — °F (°C) 45 (7)
PERFORMANCE DATAAll data is based on: • Engine operating with fuel system, water pump, lubricating oil pump, air cleaner and exhaust
silencer; not included are battery charging alternator, fan, and optional driven components.• Engine operating with fuel corresponding to grade No. 2-D per ASTM D975.• ISO 3046, Part 1, Standard Reference Conditions of:
Barometric Pressure : 100 kPa (29.53 in Hg) Air Temperature : 25 °C (77 °F)Altitude : 110 m (361 ft) Relative Humidity : 30%
Steady State Stability Band at any Constant Load ................................................................................................................— % +/- 0.25Estimated Free Field Sound Pressure Level of a Typical Generator Set; Excludes Exhaust Noise; at Rated Load and 7.5 m (24.6 ft); 1800 rpm / 1500 rpm....................................................... — dBA 94.6 / 92.4Exhaust Noise at 1 m Horizontally from Centerline of Exhaust Pipe Outlet Upwards at 45° — 1800 / 1500 rpm.....— dBA 126 / 125
STANDBY PRIME POWERPOWER UNLIMITED TIME
60 hz 50 hz 60 hz 50 hz
Governed Engine Speed..............................................................— rpm 1800 1500 1800 1500Engine Idle Speed ....................................................................... — rpm 725 - 775 725 - 775 725 - 775 725 - 775Gross Engine Power Output...........................................— BHP (kWm) 1850 (1380) 1645 (1227) 1635 (1220) 1470 (1097)Brake Mean Effective Pressure.......................................... — psi (kPa) 265 (1827) 283 (1951) 235 (1620) 253 (1744)Piston Speed.................................................................— ft / min (m / s) 1875 (9.5) 1562 (7.9) 1875 (9.5) 1562 (7.9)Friction Horsepower ......................................................... — HP (kWm) 225 (168) 155 (116) 225 (168) 155 (116)Engine Water Flow at Stated Friction Head External to Engine:
• 4 psi Friction Head...........................................— US gpm (liter / s) 535 (33.7) 440 (27.8) 535 (33.7) 440 (27.8)• Maximum Friction Head..................................— US gpm (liter / s) 470 (29.6) 400 (25.2) 470 (29.6) 400 (25.2)
Engine Data with Dry Type Exhaust ManifoldIntake Air Flow ................................................................— cfm (liter / s) 3900 (1840) 3700 (1746) 3700 (1746) 3400 (1605)Exhaust Gas Temperature......................................................— °F (°C) 887 (475) 977 (525) 860 (460) 968 (520)Exhaust Gas Flow ..........................................................— cfm (liter / s) 9100 (4295) 8500 (4011) 8400 (3964) 7900 (3728)Air to Fuel Ratio .....................................................................— air : fuel 26.5 : 1 27.0 : 1 27.5 : 1 28.0 : 1Radiated Heat to Ambient .....................................— BTU / min (kWm) 10000 (176) 8500 (150) 8500 (150) 7300 (130)Heat Rejection to Coolant ......................................— BTU / min (kWm) 51000 (900) 44000 (775) 44000 (775) 38500 (680)Heat Rejection to Exhaust......................................— BTU / min (kWm) 53000 (935) 48000 (845) 47000 (830) 43000 (760)
N.A. - Data is Not AvailableN/A - Not Applicable to this EngineTBD - To Be Determined
EC Series
Control SystemPLC-7420
FEATURES
Microprocessor control, with high stability and credibilityMonitoring and measuring operational parameters of themains supply and gensetIndicating operation status, fault conditions, all parame-ters and alarmsMultiple protections; multiple parameters display, likepressure, temp. etc.Manual, automatic and remote work mode selectable
Real time clock for time and date display, overall runtimedisplay, 250 log entries
Overall power output display
Integral speed/frequency detecting, telling status ofstart, rated operation, overspeed etc.Communication with PC via RS485 OR RS232 interface,using MODBUS protocol
PLC-7420 is an advanced control module based on micro-processor, containing all necessary functions for protection of the genset and the breaker control. It can monitor the mains supply, breaker control. and automatically start the engine when the mains is abnormal. Accurately measure various operational parameters and display all values and alarms information on the LCD. In addition, the control module can automaticallyshut down the engine and indicate the engine failure.
Gene
ral a
cces
sory
Oper
ator
Inte
rfac
eM
easu
rem
ent a
nd In
stru
men
tatio
nSh
utdo
wn
Prot
ectio
n an
d In
dica
tion
Thre
shol
d W
arni
ng&I
ndic
atio
nPa
ralle
ling
Capa
bilit
yPo
wer
Tran
sfer
Func
tion
Envi
ronm
ent
Mon
itorin
g Fu
nctio
n
Engi
neEn
gine
Alta
mat
orAl
tam
ator
Mai
ns E
xpre
ssio
n
AVRElectronic GoverningGlow plug controlCycle Cranking(MODBUS)NetworkingFault Historymanual start/stopAuto/remote startRegular TestAuto operation LEDManual operation LEDCommon Shutdown LEDCommon warning LEDFail to start LEDEmergency stop(local)Alphanumeric screenRemote start input active LEDAlarm reset Oil pressure Water Temperture Engine Speed Hours Run Number of Starts Battery Voltage Coolant Temperature 3PhaseL-L Voltage&Frequency 3phase Current Frequency kWh Apparent Power Active Power and Reactive Power Power Factor Per PhasekW, kWr Per Phase kVA Phase Voltage Output Power Grid Line Voltage Grid Phase Voltage Grid Frequency
Low Fuel Level High Fuel Level Low Oil Pressure High Water Temperature Failure to Stop Failure to Start Controlable start circles/times Overspeed Under&Over Voltage Under&Over Frequency Overcurrent Earth Leakage Reverse Power Reverse kWrLow Oil PressureLow Water TemperatureHigh Water TemperatureLow Water LevelLow/High Battery VoltageFailure to ChargeOvercurrentOverloadGenset Under/Over VoltageGenset Under/Over Frequencyunder/over SpeedHigh Engine TemperatureEarth LeakageSynchroscope(Independent Bus) Active and Reactive Power Control Synchroscope(Shared Bus) Synchronization Dector Peak Lopping
Automatic Transfer Hard Closed Transition Soft Closed Transtion Gen/Mains Breaker Gen/Mains Breaker Status Protection Speed/Voltage Control Power Indication Fuel&solenoid Valve Control Startor Control Preheating Mains Transfer Switch (Standard) Mains Transfer Switch (Emergency)Operating Temperature (-40℃-70℃) Ambient Temperature (-25℃-45℃) Humidity≤80%
Grid Over/Under Voltage Control Grid Over/Under Frequency Control Remote Start Output(Load/No-load) Optional Relay Output Remote Telecom Control with All Functions Engine Instrument Monitoring Altemator Output Instrument Monitoring Connection Point with All-around Setting For 6 Users 3 Users Input Connection Point LCD Light Control of Low Light Operation Environment Safe PIN CodeRS232/485 Interface Language Selection Multi-Language Function
MODEL
Standard Optional Impossible
PLC-7420
Control System function listPLC-8610
GMS1250C / GMS1250CS
Control System
PLC-8610 (Optional)
Digital, intelligent controlsystem allows easier operation.
FEATURES
Microprocessor control, with high stability and credibilityMonitoring and measuring operational parameters of the genset
Indicating operation status, fault conditions, all parametersand alarmsMultiple protections; multiple parameters display, like pressure, temp. etc.Manual, automatic and remote work mode selectable
RS232 & RS485 can be used at the same time
Real time clock for time and date display, overall runtime display, 250 log entries
PLC-8610 is a microprocessor based control unit containing all
circuits and presents all values and alarms on the LCD display. The
other gensets. The load sharing is performed so each genset takesa portion of the load that is calculated in percent according to thenominal power.
necessary functions for protection of the genset and the breakercontrol. Furthermore, it contains all necessary three-phase measuring
module has the function of load sharing which enables the moduleto share the active load (kW) equally when operating in parallel with
GMS1250C / GMS1250CSEC Series
Engine Alternator Generator Set Fuel System Canopy
Exhaust System Cooling System Control Panel Voltages
● Water Jacket Preheater● Oil Preheater
Optional
● Winding Temperature Measuring Instrument● Alternator Preheater● PMG ● Anti-damp and anti-corrosion treatment● Anti-condensation heater
● Tools with the machine ● Low fuel level alarm● Automatic fuel feeding system● Fuel T-valves
● Oil with the machine ● Protection board from hotness
● Front heat protection● Coolant (-30°C)
● Remote control panel● PLC-8610● PLC-7420● ATS
● 415/240V● 400/230V● 380/220V● 220/127V● 200-115V
Lubricating System
www.powerlinkworld.com
PowerLink reserves the right to make changes in model, technical sepcification, color, configuration and accessories without prior notice. Please contact the salesman before ordering.
EC Series / May.2013
GMS1250C / GMS1250CSEC Series
GMS1250C / GMS1250CS
Features:
EC Series
M: Mechanical speed governor, E/ECU: Electronic speed governor;NA: Naturally aspirated, TC: Turbocharged, TCA: Turbocharged and air-air aftercooled. TCW: Water-cooled Turbocharged;The weights are approximate and without fuel.
Also available in the following voltages: 415/240V-380/220V-220/127V-200/115V; ESP: Standby Power Standby duty, operation under variable load, without over load;PRP: Prime Power-Continuous duty operation, under variable load 24/24h-10% over load permissible 1 hour/12 hours;The data is only for your reference but not for use of sales.
Ratings at 0.8 power factor.
Generating Set Model Prime Standby
GMS1250C/S N/A 1250kVA/1000kW
Output Ratings
Ratings and Performance Data Dimensions and Weights
• Excitation system: self-excited (AREP and PMG are optional)
• ATS (automatic transfer switch) receptacle
• Lockable battery isolator switch
• Stainless galvanized zinc plates with strong
corrosion resistance
• Vibration isolators between the engine/alternator
and base frame
• Integrated wiring design
• Base fuel tank for at least 8 hours running
• Equipped with an industrial muffler
• Engine oil pump
• 50℃ radiator
• Top lifting and steel base frame with forklift holes
• Drainage for fuel tank
• Complete protection functions and safety labels
• IP54 (soundproof sets), IP56 (control system)
• Water jacket preheater, oil heater and double air
cleaner, etc. are available.
Prime
Standby
Structure Type:
Fuel Tank Capacity: L
(100% Load)Fuel Consumption: l/hr
GMS1250C
GMS1250CS
GMS1250C
GMS1250CS
Engine Make & Model:
Alternator Model:
Alternator Brand:
Control System:
Noise Level@7m:
Frequency & Phase:
Engine Speed: RPM
KTA38-G9
LVI634G
STAMFORD
PLC-8610 / PLC-7420
75.1-85.2
50Hz & 3PH
1500
A
C
/
1500
233
256
Dry = With Lube Oil Wet = With Lube Oil and Coolant
Length (L)mm (in)
Width (W)mm (in)
Height (H)mm (in)
Drykg (lb)
GeneratingSet Model
GMS1250C
GMS1250CS
5088 2110 2230 9660
6058 2438 2830 15308
utput Ratings
Engine model: KTA38-G9
GMS1250C / GMS1250CSEC Series
GENERAL ENGINE DATAType................................................................................................................................................................ 4-Cycle; 60° Vee; 12-Cylinder DieselAspiration........................................................................................................................................................ Turbocharged and Aftercooled
Bore x Stroke ..............................................................................................................— mm x mm (in x in) 159 x 159 (6.25 x 6.25)Displacement ..............................................................................................................................— litre (in3) 2300 (37.8)Compression Ratio........................................................................................................................................ 13.9 : 1
Dry WeightFan to Flywheel Engine ........................................................................................................ — kg (lb) 4300 (9482)
Wet WeightFan to Flywheel Engine......................................................................................................... — kg (lb) 4536 (10002)
Moment of Inertia of Rotating Components • with FW 6001 Flywheel ........................................................................................... — kg • m2 (lbm • ft2) 10.4 (248) • with FW 6011 Flywheel............................................................................................ — kg • m2 (lbm • ft2) 20.8 (493)Center of Gravity from Front Face of Block............................................................................... — mm (in) 980 (38.6)Center of Gravity Above Crankshaft Centerline........................................................................ — mm (in) 279 (11)Maximum Static Loading at Rear Main Bearing......................................................................... — kg (lb) 908 (2000)
ENGINE MOUNTINGMaximum Bending Moment at Rear Face of Block.......................................................... — N • m (lb • ft) 6100 (4500)
EXHAUST SYSTEMMaximum Back Pressure at 1500 RPM (Standby Power)........................................... — mm Hg (in Hg) 76 (3)
AIR INDUCTION SYSTEMMaximum Intake Air Restriction • with Dirty Filter Element ................................................................................................. — kPa (in H2O) 6.2 (25) • with Clean Filter Element............................................................................................... — kPa (in H2O) 3.7 (15)
COOLING SYSTEM Coolant Capacity — Engine only .................................................................................... — litre (US gal) 124 (32.7)
— with HX 6076 Heat Exchanger ..................................................... — litre (US gal) 199 (52.7)Minimum Pressure Cap (for Cooling Systems with less than 2m [6 ft.] Static Head)........... — kPa (psi) 69 (10)Maximum Static Head of Coolant Above Engine Crank Centerline........................................... — m (ft) 18.3 (60)Thermostat (Modulating) Range ...............................................................................................— °C (°F) .. 82-93 (180-200)Maximum Coolant Friction Head External to Engine — 1500 rpm ....................................... — kPa (psi) 48 (7)Maximum Top Tank Temperature for Standby...........................................................................— °C (°F) 104 (220)Maximum Raw Water Flow @ 90 F to HX6076 Heat Exchanger.......................... — liter/min (US gpm) 409 (108)Maximum Raw Water Inlet Pressure at HX 6076 Heat Exchanger ...................................... — kPa (psi) 345 (50)
LUBRICATION SYSTEMOil Pressure @ Idle Speed..................................................................................................... — kPa (psi) 138 (20)
@ Governed Speed.......................................................................................... — kPa (psi) 310-448 (45-65)Maximum Oil Temperature ......................................................................................................... — °C (°F) 121 (250)Oil Capacity with OP6023 Oil Pan: Low - High................................................................. — litre (US gal) 114-87 (30-23)Total System Capacity (with Combo Filter)....................................................................... — litre (US gal) 135 (35.7)
Engine model: KTA38-G9
GMS1250C / GMS1250CSEC Series
N.A. - Data is Not AvailableN/A - Not Applicable to this EngineTBD - To Be Determined
NotApplicablefor 60 HzOperation
FUEL SYSTEMType Injection System ..................................................................................................................................................................... Direct Injection Cummins PTMaximum Restriction at PT Fuel Injection Pump — with Clean Fuel Filter.................................................— mm Hg (in Hg) 102 (4.0)
— with Dirty Fuel Filter.................................................. — mm Hg (in Hg) 203 (8.0)Maximum Allowable Head on Injector Return Line (Consisting of Friction Head and Static Head)............. — mm Hg (in Hg) 165 (6.5)Maximum Fuel Inlet Temperature ........................................................................................................................... —°C (°F) 70 (160)Maximum Fuel Flow to Injection Pump......................................................................................................... — litre / hr (US gph) 428 (113)
ELECTRICAL SYSTEMCranking Motor (Heavy Duty, Positive Engagement)......................................................................................................... — volt 24Battery Charging System, Negative Ground.................................................................................................................--- ampere 35Maximum Allowable Resistance of Cranking Circuit........................................................................................................ — ohm .002Minimum Recommended Battery Capacity
• Cold Soak @ 10 °C (50 °F) and Above.............................................................................................................. — 0°F CCA 1200• Cold Soak @ 0 °C to 10 °C (32 °F to 50 °F)...................................................................................................... — 0°F CCA 1280• Cold Soak @ -18 °C to 0 °C (0 °F to 32 °F)....................................................................................................... — 0°F CCA 1800
COLD START CAPABILITYMinimum Ambient Temperature for Unaided Cold Start to Idle Speed......................................................................— °C (°F) 7 (45)Minimum Ambient Temperature for NFPA 110 Cold Start (90° F Minimum Coolant Temperature)........................— °C (°F) 10 (50)
PERFORMANCE DATAAll data is based on: • Engine operating with fuel system, water pump, lubricating oil pump, air cleaner and exhaust
silencer; not included are battery charging alternator, fan, and optional driven components.• Engine operating with fuel corresponding to grade No. 2-D per ASTM D975.• ISO 3046, Part 1, Standard Reference Conditions of:
Barometric Pressure : 100 kPa (29.53 in Hg) Air Temperature : 25 °C (77 °F)Altitude : 110 m (361 ft) Relative Humidity : 30%
Steady State Stability Band at any Constant Load .............................................................................................................. — % +/- 0.25Estimated Free Field Sound Pressure Level of a Typical Generator Set;
Excludes Exhaust Noise; at Rated Load and 7.5 m (24.6 ft); 1800 rpm ................................................................. — dBA N.A.Exhaust Noise at 1 m Horizontally from Centerline of Exhaust Pipe Outlet Upwards at 45°.......................................... — dBA N.A
STANDBY POWER50 hz
Governed Engine Speed............................................................. — rpm 1500Engine Idle Speed....................................................................... — rpm 725-775Gross Engine Power Output.......................................... — kWm (BHP) 1089 (1460)Brake Mean Effective Pressure .......................................... — kPa (psi) 2296 (333)Piston Speed................................................................— m / s (ft / min) 7.9 (1562)Friction Horsepower.......................................................... — kWm (HP) 86 (115)Engine Jacket Water Flow at Stated Friction Head External to Engine:
• 4 psi Friction Head...........................................— litre / s (US gpm) 19.6 (310)• Maximum Friction Head..................................— litre / s (US gpm) 17.7 (280)
Engine DataIntake Air Flow.................................................................— litre / s (cfm) 1309 (2775)Exhaust Gas Temperature..................................................... — °C (°F) 529 (985)Exhaust Gas Flow...........................................................— litre / s (cfm) 3540 (7500)Air to Fuel Ratio......................................................................— air : fuel 24.8:1Radiated Heat to Ambient .....................................— kWm (BTU / min) 154 (8764)Heat Rejection to Engine Jacket Radiator.............— kWm (BTU / min) 672 (38243)Heat Rejection to Exhaust.....................................— kWm (BTU / min) 652 (37082)
EC Series
Control SystemPLC-7420
FEATURES
Microprocessor control, with high stability and credibilityMonitoring and measuring operational parameters of themains supply and gensetIndicating operation status, fault conditions, all parame-ters and alarmsMultiple protections; multiple parameters display, likepressure, temp. etc.Manual, automatic and remote work mode selectable
Real time clock for time and date display, overall runtimedisplay, 250 log entries
Overall power output display
Integral speed/frequency detecting, telling status ofstart, rated operation, overspeed etc.Communication with PC via RS485 OR RS232 interface,using MODBUS protocol
PLC-7420 is an advanced control module based on micro-processor, containing all necessary functions for protection of the genset and the breaker control. It can monitor the mains supply, breaker control. and automatically start the engine when the mains is abnormal. Accurately measure various operational parameters and display all values and alarms information on the LCD. In addition, the control module can automaticallyshut down the engine and indicate the engine failure.
Gene
ral a
cces
sory
Oper
ator
Inte
rfac
eM
easu
rem
ent a
nd In
stru
men
tatio
nSh
utdo
wn
Prot
ectio
n an
d In
dica
tion
Thre
shol
d W
arni
ng&I
ndic
atio
nPa
ralle
ling
Capa
bilit
yPo
wer
Tran
sfer
Func
tion
Envi
ronm
ent
Mon
itorin
g Fu
nctio
n
Engi
neEn
gine
Alta
mat
orAl
tam
ator
Mai
ns E
xpre
ssio
n
AVRElectronic GoverningGlow plug controlCycle Cranking(MODBUS)NetworkingFault Historymanual start/stopAuto/remote startRegular TestAuto operation LEDManual operation LEDCommon Shutdown LEDCommon warning LEDFail to start LEDEmergency stop(local)Alphanumeric screenRemote start input active LEDAlarm reset Oil pressure Water Temperture Engine Speed Hours Run Number of Starts Battery Voltage Coolant Temperature 3PhaseL-L Voltage&Frequency 3phase Current Frequency kWh Apparent Power Active Power and Reactive Power Power Factor Per PhasekW, kWr Per Phase kVA Phase Voltage Output Power Grid Line Voltage Grid Phase Voltage Grid Frequency
Low Fuel Level High Fuel Level Low Oil Pressure High Water Temperature Failure to Stop Failure to Start Controlable start circles/times Overspeed Under&Over Voltage Under&Over Frequency Overcurrent Earth Leakage Reverse Power Reverse kWrLow Oil PressureLow Water TemperatureHigh Water TemperatureLow Water LevelLow/High Battery VoltageFailure to ChargeOvercurrentOverloadGenset Under/Over VoltageGenset Under/Over Frequencyunder/over SpeedHigh Engine TemperatureEarth LeakageSynchroscope(Independent Bus) Active and Reactive Power Control Synchroscope(Shared Bus) Synchronization Dector Peak Lopping
Automatic Transfer Hard Closed Transition Soft Closed Transtion Gen/Mains Breaker Gen/Mains Breaker Status Protection Speed/Voltage Control Power Indication Fuel&solenoid Valve Control Startor Control Preheating Mains Transfer Switch (Standard) Mains Transfer Switch (Emergency)Operating Temperature (-40℃-70℃) Ambient Temperature (-25℃-45℃) Humidity≤80%
Grid Over/Under Voltage Control Grid Over/Under Frequency Control Remote Start Output(Load/No-load) Optional Relay Output Remote Telecom Control with All Functions Engine Instrument Monitoring Altemator Output Instrument Monitoring Connection Point with All-around Setting For 6 Users 3 Users Input Connection Point LCD Light Control of Low Light Operation Environment Safe PIN CodeRS232/485 Interface Language Selection Multi-Language Function
MODEL
Standard Optional Impossible
PLC-7420
Control System function listPLC-8610
GMS1250C / GMS1250CS
Control System
PLC-8610 (Optional)
Digital, intelligent controlsystem allows easier operation.
FEATURES
Microprocessor control, with high stability and credibilityMonitoring and measuring operational parameters of the genset
Indicating operation status, fault conditions, all parametersand alarmsMultiple protections; multiple parameters display, like pressure, temp. etc.Manual, automatic and remote work mode selectable
RS232 & RS485 can be used at the same time
Real time clock for time and date display, overall runtime display, 250 log entries
PLC-8610 is a microprocessor based control unit containing all
circuits and presents all values and alarms on the LCD display. The
other gensets. The load sharing is performed so each genset takesa portion of the load that is calculated in percent according to thenominal power.
necessary functions for protection of the genset and the breakercontrol. Furthermore, it contains all necessary three-phase measuring
module has the function of load sharing which enables the moduleto share the active load (kW) equally when operating in parallel with
GMS1250C / GMS1250CSEC Series
Engine Alternator Generator Set Fuel System Canopy
Exhaust System Cooling System Control Panel Voltages
● Water Jacket Preheater● Oil Preheater
Optional
● Winding Temperature Measuring Instrument● Alternator Preheater● PMG ● Anti-damp and anti-corrosion treatment● Anti-condensation heater
● Tools with the machine ● Low fuel level alarm● Automatic fuel feeding system● Fuel T-valves
● Oil with the machine ● Protection board from hotness
● Front heat protection● Coolant (-30°C)
● Remote control panel● PLC-8610● PLC-7420● ATS
● 415/240V● 400/230V● 380/220V● 220/127V● 200-115V
Lubricating System
www.powerlinkworld.com
PowerLink reserves the right to make changes in model, technical sepcification, color, configuration and accessories without prior notice. Please contact the salesman before ordering.
EC Series / May.2013
GMS1250C / GMS1250CSEC Series