ELEC 313 FALL 2011

Lab Report & Notebook Guidelines

Basic Requirements

Succinct and clearly written.Sufficient description to enable an engineer

familiar with basic electrical measurements to reproduce your results.

Printed output from a word processor.Figures may be hand-drawn, if necessary.Proper grammar, punctuation, spelling

expected

Formatting

Typed in 10 or 12 point type formulae typeset using an equation editorSame font and form for all headings.One inch left & right margins Number every page of the report, but don’t

show number for cover page.Cite your source as a reference (a number

in square brackets, e.g. [1])A list of references at end of report (IEEE)

Tables & Figures

Tables and figures must have a title, a number, and a caption (above for table, below for figure).

Referenced in the text by title and numberSpecify unit of measure associated with

variableUse table when there is no relation

between subsequent datum.

Required Elements

Cover pagePurpose of experimentTest configuration Circuit testedTest procedureMeasured results/Comparison with

theoretical resultsConclusion

Cover Page

Course/section numberAssignment numberExperiment titleEngineer namesEngineer signaturesDate of submission

ELEC 204-01

Technical Report for Lab Assignment #0

Resistor Combinations in Series

G. KirchhoffE.L. Thevenin

January 31, 1872

Purpose of Experiment

State theoretical principles or concepts that this experiment is trying to prove.

May also be to gain experience in using the lab equipment.

Test Configuration

Block DiagramInstrument Manufacturer/Model Number

HP34401A

MULTIMETER

RESISTORNETWORK

UNDER TEST

Circuit Tested

Schematic of circuitReference designatorsNominal element values should be given.

R2

R1

1.5K

7.5K

Test Procedure

Enough description that the experiment could be reproduced by anyone familiar with basic electrical measurements.

Sequential in narrative style (i.e., no bulleting or numbering)

Do not just copy the instruction lists in the lab assignments.

Write in third person, past tense, passive voice.

First Person

We connected the function generator to the input port of the circuit.

Second Person

We connected the function generator to the input port of the circuit.

Connect the function generator to the input port of the circuit.

Third Person

We connected the function generator to the input port of the circuit.

Connect the function generator to the input port of the circuit.

The function generator was connected to the input port of the circuit.

Measured Results

Nominal value is the value expected by looking at the markings on the device.

Measured value is read off the test equipment during the experiment.

Use tables where appropriate.Deviation from nominal

%100%

nominal

nominalmeasureddeviation

Comparison with Theoretical

Measured values versus what would be predicted by a theoretical analysis of the circuit performance, e.g., compare the measured resistance of two resistors connected in series with R1+R2.

Express comparison as a %error.

Discussion of results in present tense, passive voice

%100%

ltheoretica

ltheoreticameasurederror

Conclusions

What theoretical principle or concept did this experiment prove?

Describe how the principle is supported by your findings/data.

Within experimental error, this laboratory exercise has demonstrated that the equivalent resistance of two resistors connected in series is equal to the sum of the individual values.

Conclusions

What theoretical principle or concept did this experiment prove?

Within experimental error, this laboratory exercise has demonstrated that the equivalent resistance of two resistors connected in series is equal to the sum of the individual values.

“I learned a lot” or “it was fun” are not valid conclusions.

Typical Grading Form

Lab Notebooks

Most companies require their engineers to keep notebooks of their work.

Effective evidence in patent disputesChronological account of work helps

engineers remember what has been done.

Requirements

Bound volume. Loose leaf notebooks are not acceptable.

All pages must be sequentially numbered. Each side of a sheet is considered a page.

The first sheet should be reserved for a table of contents.

Label the first page used for a particular experiment with the title of that experiment, and reference the page number in the Table of Contents.

Requirements

Make all entries in ink.Do not erase entries. To delete information,

cross it out with a single line.The date entries were made must appear on

every page.Each page must be signed by the engineer

taking the data.

Requirements

No blank numbered pages are permitted. Write “This page intentionally left blank.” if necessary.

Any added material, such as PSPICE plot, must be permanently affixed using tape or glue. The material itself must be signed and dated.

Summary

A lab notebook is not intended to be a publication quality document.

It is first and foremost a chronological record of the daily work of an engineer.

As such, it can serve as a valuable legal document and guide for others carrying the work forward.