1P 1 POLE (2P, 3P, 4P, ETC.) A AMPERE AC ABOVE COUNTER OR AIR CONDITIONER ACLG ABOVE CEILING ADO AUTOMATIC DOOR OPENER AF AMP FRAME AFF ABOVE FINISHED FLOOR AFG ABOVE FINISHED GRADE AFI ARC FAULT CIRCUIT INTERRUPTER AHU AIR HANDLING UNIT AL ALUMINUM ALT ALTERNATE AMP AMPERE AMPL AMPLIFIER ANNUN ANNUNCIATOR APPROX APPROXIMATELY AQ-STAT AQUASTAT ARCH ARCHITECT, ARCHITECTURAL AS AMP SWITCH AT AMP TRIP ATS AUTOMATIC TRANSFER SWITCH AUTO AUTOMATIC AUX AUXILIARY AV AUDIO VISUAL AWG AMERICAN WIRE GAUGE BATT BATTERY BD BOARD BLDG BUILDING BMS BUILDING MANAGEMENT SYSTEM C CONDUIT CAB CABINET CAT CATALOG CATV CABLE TELEVISION CB CIRCUIT BREAKER CCTV CLOSED CIRCUIT TELEVISION CKT CIRCUIT CLG CEILING COMB COMBINATION CMPR COMPRESSOR CONN CONNECTION CONST CONSTRUCTION CONT CONTINUATION OR CONTINUOUS CONTR CONTRACTOR CONV CONVECTOR CP CIRCULATING PUMP CRT CATHODE-RAY TUBE CT CURRENT TRANSFORMER CTR CENTER CU COPPER DCP DOMESTIC WATER CIRCULATING PUMP DEPT DEPARTMENT DET DETAIL DIA DIAMETER DISC DISCONNECT DIST DISTRIBUTION DN DOWN DPR DAMPER DS SAFETY DISCONNECT SWITCH DT DOUBLE THROW DWG DRAWING EC ELECTRICAL CONTRACTOR ELEC ELECTRIC, ELECTRICAL ELEV ELEVATOR EM EMERGENCY EMS ENERGY MANAGEMENT SYSTEM EMT ELECTRICAL METALLIC TUBING EP ELECTRIC PNEUMATIC EQUIP EQUIPMENT EWC ELECTRIC WATER COOLER EXIST EXISTING EXH EXHAUST EXP EXPLOSION PROOF FA FIRE ALARM FABP FIRE ALARM BOOSTER POWER SUPPLY PANEL FACP FIRE ALARM CONTROL PANEL FCU FAN COIL UNIT FIXT FIXTURE FLR FLOOR FLUOR FLUORESCENT FU FUSE FUDS FUSED SAFETY DISCONNECT SWITCH GA GAUGE GAL GALLON GALV GALVANIZED GC GENERAL CONTRACTOR GEN GENERATOR GFI GROUND FAULT CIRCUIT INTERRUPTER GFP GROUND FAULT PROTECTOR GND GROUND GRS GALVANIZED RIGID STEEL (CONDUIT) GYP BD GYPSUM BOARD HOA HANDS-OFF-AUTOMATIC SWITCH HORIZ HORIZONTAL HP HORSEPOWER HPF HIGH POWER FACTOR HT HEIGHT HTG HEATING HTR HEATER HV HIGH VOLTAGE HVAC HEATING, VENTILATING AND AIR CONDITIONING HWP HYDRONIC WATER PUMP IC INTERRUPTING CAPACITY IG ISOLATED GROUND IMC INTERMEDIATE METAL CONDUIT INCAND INCANDESCENT IR INFRARED I/W INTERLOCK WITH J-BOX JUNCTION BOX KV KILOVOLT KVA KILOVOLT-AMPERE KVAR KILOVOLT-AMPERE REACTIVE KW KILOWATT KWH KILOWATT HOUR LOC LOCATE OR LOCATION LT LIGHT LTG LIGHTING LTNG LIGHTNING LV LOW VOLTAGE MAX MAXIMUM MAG.S MAGNETIC STARTER M/C MOMENTARY CONTACT MC MECHANICAL CONTRACTOR MCB MAIN CIRCUIT BREAKER MCC MOTOR CONTROL CENTER MDC MAIN DISTRIBUTION CENTER MDP MAIN DISTRIBUTION PANEL MFR MANUFACTURER MFS MAIN FUSED DISCONNECT SWITCH MH MANHOLE MIC MICROPHONE MIN MINIMUM MISC MISCELLANEOUS MLO MAIN LUGS ONLY MMS MANUAL MOTOR STARTER MOA MULTIOUTLET ASSEMBLY MSP MOTOR STARTER PANELBOARD MSBD MAIN SWITCHBOARD MT MOUNT MT.C EMPTY CONDUIT MTS MANUAL TRANSFER SWITCH MTR MOTOR, MOTORIZED N.C. NORMALLY CLOSED NEC NATIONAL ELECTRICAL CODE NEMA NATIONAL ELECTRICAL MANUFACTURER'S ASSOCIATION NFDS NON-FUSED SAFETY DISCONNECT SWITCH NIC NOT IN CONTRACT NL NIGHT LIGHT N.O. NORMALLY OPEN NPF NORMAL POWER FACTOR NTS NOT TO SCALE OH OVERHEAD OL OVERLOADS PA PUBLIC ADDRESS PB PULL BOX OR PUSHBUTTON PE PNEUMATIC ELECTRIC PED PEDESTAL PF POWER FACTOR PH PHASE PIV POST INDICATING VALVE PNL PANEL PP POWER POLE PR PAIR PRI PRIMARY PROJ PROJECTION PRV POWER ROOF VENTILATOR PT POTENTIAL TRANSFORMER PVC POLYVINYL CHLORIDE (CONDUIT) PWR POWER QUAN QUANTITY RCPT RECEPTACLE REQD REQUIRED RM ROOM RSC RIGID STEEL CONDUIT RTU ROOF TOP UNIT SC SURFACE CONDUIT SEC SECONDARY SHT SHEET SIM SIMILAR S/N SOLID NEUTRAL SPEC SPECIFICATION SPKR SPEAKER SP SPARE SR SURFACE RACEWAY SS STAINLESS STEEL SSW SELECTOR SWITCH S/S STOP/START PUSHBUTTONS STA STATION STD STANDARD SURF SURFACE MOUNTED SW SWITCH ELECTRICAL ABBREVIATIONS LIST SWBD SWITCHBOARD SYM SYMMETRICAL SYS SYSTEM TEL TELEPHONE TEL/DATA TELEPHONE/DATA TERM TERMINAL TL TWIST LOCK TR TAMPER RESISTANT T-STAT THERMOSTAT TTC TELEPHONE TERMINAL CABINET TV TELEVISION TVTC TELEVISION TERMINAL CABINET TYP TYPICAL UC UNDER COUNTER UE UNDERGROUND ELECTRICAL UG UNDERGROUND UH UNIT HEATER UT UNDERGROUND TELEPHONE UTIL UTILITY UV UNIT VENTILATOR OR ULTRAVIOLET V VOLT VA VOLT-AMPERES VDT VIDEO DISPLAY TERMINAL VERT VERTICAL VFD VARIABLE FREQUENCY DRIVE VOL VOLUME W WATT W/ WITH WG WIRE GUARD WH WATER HEATER W/O WITHOUT WP WEATHERPROOF XFMR TRANSFORMER XFR TRANSFER ANGLE @ AT DELTA ' FEET INCHES NUMBER Ø PHASE C CENTER LINE P PLATE L L EMERGENCY LIGHT FIXTURE SYMBOL *** DISTANCE TO HIGHEST OPERABLE PART OF EQUIPMENT 72"** CIRCUIT BREAKER PANEL SINGLE POLE SW. DIMMER SWITCH OCCUPANCY SENSOR SWITCH PUSH BUTTON SINGLE RECEPT. FAN SPEED CONTROL SPLIT DUPLEX RECEPT/SWITCHED FOURPLEX RECEPT. DUPLEX RECEPT. RECEPT ON EMERGENCY CKT (DUPLEX SHOWN) ISOLATED GROUND RECEPT (DUPLEX SHOWN) EQUIPMENT PLUG RECEPT ON DROP CORD (DUPLEX SHOWN) RECEPT ON CORD REEL (DUPLEX SHOWN) FLOOR RECEPT. (DUPLEX SHOWN) ALL DISTANCES ARE TO CENTER OF DEVICE OR EQUIPMENT UNLESS OTHERWISE NOTED. DEVICES INDICATED AT 48" MAY NOT BE INSTALLED WIT H ANY OPERABLE PART HIGHER THAN 48". DEVICES MAY BE INSTALLED IN CONCRETE MASONRY UNITS WITH THE TOP OF THE DEVICE AT 48". AS NOTED * DISTANCE ABOVE TOP OF DOOR FRAME J TIMER SWITCH AS NOTED 48" 3 KEYED SW. SW. W/PILOT 3-WAY SW. 4-WAY SW. PER SCHED WALL HEATER (TYPE DENOTED) ** DISTANCE TO TOP OF EQUIPMENT OR DEVICE PER SCHED D1 H2 HATCHED SYMBOL INDICATES REMOVED HAND OR HAIR DRYER (TYPE DENOTED) DASHED SYMBOL INDICATES EXISTING SOLENOID VALVE AS NOTED AS NOTED 48" 48" PER SCHED 48" AS NOTED H T H1 TC 72"** 72"** OS R 72"** 72"** 72"** 72"** 72"** 72"** 72"** SF-1 T LIGHT LEVEL SENSOR - TYPE DENOTED TIME CONTROL SWITCH (TIME SWITCH) BASEBOARD HEATER (TYPE DENOTED) HUMIDISTAT THERMOSTAT PHOTOCELL ENCLOSED CIRCUIT BREAKER RELAY 48" 84" 84" COMB. MOTOR STARTER (NON-FUSED) MAG. MOTOR STARTER OR CONTACTOR SAFETY DISC. SW. (FUSED) SAFETY DISC. SW. (NON-FUSED) COMB. MOTOR STARTER (FUSED) POWER OR DISTRIBUTION PANEL MOTOR (SEE SCHEDULE) TRANSFORMER (TYPE DENOTED) MOTOR HORSEPOWER RATED SWITCH SPECIAL CABINET (TYPE DENOTED) 48"*** 18" 48" 18" DESCRIPTION WALL MOUNTED EXTERIOR LIGHT (TYPE DENOTED) POLE MOUNTED LIGHT (TYPE DENOTED) RECESSED LIGHT (TYPE DENOTED) SURFACE OR WALL MTD LIGHT (TYPE DENOTED) EXIT SIGN (TYPE DENOTED) SUSPENDED OR PENDANT LIGHT (TYPE DENOTED) TRACK AND TRACK LIGHT (TYPES DENOTED) SURFACE LIGHT (TYPE DENOTED) STRIP LIGHT (TYPE DENOTED) EMERGENCY BATTERY LIGHT (TYPE DENOTED) RECESSED LIGHT (TYPE DENOTED) PER SCHED AS NOTED 12"* 96" P2 P1 TR1 T1 T1 E E EM H G AA R HT AFF AS NOTED SYMBOL AS NOTED AS NOTED J J 84" A P HT AFF 18" 18" SYMBOL A SPECIAL RECEPT. OR CONN. (SEE SCHEDULE) JUNCTION BOX PULL BOX GROUND ROD (PLAN VIEW) CLOCK (TYPE DENOTED) POWER POLE (OPEN OFFICE STYLE) MULTIOUTLET ASSEMBLY (TYPE DENOTED) MULTIOUTLET ASSEMBLY (TYPE DENOTED) DESCRIPTION HT AFF PROJECTOR CONTROL OUTLET CCTV CAMERA WITH PAN/TILT DRIVE **** DISTANCE BELOW CEILING ANTENNA CCTV CAMERA ***** DISTANCE TO BOTTOM OF DEVICE 144"* DOOR SIGNAL - APT. UNIT SPEAKER (WALL OR CEILING MT.) S MICROPHONE OUTLET VOLUME CONTROL V BUZZER D BELL INFORMATION OUTLET (TYPE DENOTED) WALL TELEPHONE OUTLET (TYPE DENOTED) INTERCOM OUTLET LOCATION TELEPHONE OUTLET (TYPE DENOTED) MULTIPLE SERVICE OUTLET (TYPE DENOTED) TELEVISION OUTLET W CARD READER ELECTRIC STRIKE MOTION DETECTOR (TYPE DENOTED) MD ES KEYPAD HEAT DETECTOR (TYPE & TEMP DENOTED) CONDUIT/WIRE DESCRIPTION SMOKE DETECTOR (TYPE DENOTED) DUCT SMOKE DETECTOR (TYPE DENOTED) R/F135 P R/F135 F ELECTRICAL SYMBOL LEGEND AS NOTED 48" 48" 48" 48" 48" 48" 48" 48" 48" 48" 18" 18" 18" 18" 18" 18" FOURPLEX RECEPTACLE ON EMERGENCY CIRCUIT 18" 4 K D O S T SP M B P B VARIABLE FREQUENCY DRIVE A LS C P OCCUPANCY SENSOR - TYPE DENOTED IC 18" 18" 48"*** 84" 18" 18" OUTLET IN FLOOR (MICROPHONE SHOWN) M MULTIPLE SERVICE FLR OUTLET (TYPE DENOTED) CHIME S M P 48"*** 48"*** P P 72"** FIRE ALARM REMOTE ANNUNCIATOR FA ANNUN CR MAGNETIC LOCK ML IR CONDUIT SLEEVE (SIZE DENOTED) 1 KEYED NOTE (SEE SCHEDULE) WIRELESS ACCESS POINT WAP AS NOTED DOOR HOLDER DOOR POWER ASSIST DC A2 12b 14 E 16c d D600 e 1,3,5 1 SF-1 2,4,6 7,9 H1 T1 LPN-102 1 #10 ELECTRICAL SYMBOL NOTES THE LIGHTING FIXTURE TYPE IS INDICATED BY AN UPPER CASE LETTER. THE CIRCUIT DESIGNATION IS INDICATED BY A NUMBER. THE SWITCH DESIGNATION IS INDICATED BY A LOWER CASE LETTER. EXAMPLE 1: LIGHTING FIXTURE TYPE "A" IS CONNECTED TO CIRCUIT 12 AND CONTROLLED BY SWITCH "b". EXAMPLE 2: THE FIXTURE TYPE SHOWN AS A NUMERATOR INDICATES ALL LIGHTING FIXTURES IN THE ROOM OR SPACE ARE THE SAME TYPE. THE CIRCUIT NUMBER AND SWITCH DESIGNATION SHOWN AS A DENOMINATOR INDICATES ALL LIGHTING FIXTURES IN THE ROOM OR SPACE ARE CONNECTED TO THE SAME CIRCUIT, CONTROLLED BY THE SAME SWITCHES, CENTER/OUTBOARD MULTILEVEL SWITCHING. EXIT LIGHTS. STEM INDICATES WALL MOUNTING. NO STEM INDICATES CEILING MOUNTING. SHADED AREA INDICATES ILLUMINATED FACE(S). ARROW INDICATES DIRECTIONAL ARROW ON ILLUMINATED FACE(S). THE CIRCUIT DESIGNATION IS INDICATED BY A NUMBER. EXAMPLE: THE WALL MOUNTED EXIT LIGHT TYPE "E" WITH SINGLE FACE AND DIRECTIONAL ARROW IS CONNECTED TO CIRCUIT 14. DEVICES. THE CIRCUIT DESIGNATION IS INDICATED BY A NUMBER. THE SWITCH DESIGNATION IS INDICATED BY A LOWER CASE LETTER. EXAMPLE: SPLIT DUPLEX RECEPTACLE IS CONNECTED TO CIRCUIT 16 AND ONE RECEPTACLE OUTLET IS CONTROLLED BY SWITCH "c". THE CONTROL DEVICE DESIGNATION IS INDICATED BY A LOWER CASE LETTER. EXAMPLE: SINGLE POLE SWITCH "d" TO CONTROL LIGHTING FIXTURES INDICATED BY "d". WALL BOX DIMMER WITH SIZE AS INDICATED AT DEVICE. EXAMPLE: 600 WATT WALL BOX DIMMER TO CONTROL LIGHTING FIXTURES INDICATED BY "e". SEE SPECIFICATIONS FOR WATTAGE IF NOT INDICATED. SPECIAL CONNECTIONS. THE EQUIPMENT IS INDICATED BY A NUMBER IN A CIRCLE. SEE THE MOTOR AND EQUIPMENT SCHEDULE FOR THE LOAD DESCRIPTION AND TYPE OF CONNECTION. THE CIRCUIT DESIGNATION IS INDICATED BY A NUMBER(S) ADJACENT TO THE SYMBOL. EXAMPLE: EQUIPMENT NO. 1; 3 PHASE CONNECTION TO CIRCUITS 1, 3, 5. MOTOR CONNECTIONS. THE MOTOR IS INDICATED BY A NUMBER WITHIN OR CHARACTERS ADJACENT TO THE MOTOR SYMBOL. SEE THE MOTOR AND EQUIPMENT SCHEDULE FOR THE MOTOR DESCRIPTION AND ELECTRICAL REQUIREMENTS. THE CIRCUIT DESIGNATION IS INDICATED BY A NUMBER(S) ADJACENT TO THE SYMBOL. EXAMPLE: MOTOR SF-1; 3 PHASE CONNECTION TO CIRCUITS 2, 4, 6. ELECTRIC HEATER CONNECTIONS. THE HEATER TYPE IS INDICATED BY A NUMBER FOLLOWING THE UPPER CASE LETTER "H". SEE THE HEATER SCHEDULE FOR ELECTRICAL REQUIREMENTS. THE CIRCUIT DESIGNATION IS INDICATED BY A NUMBER(S) ADJACENT TO THE HEATER. EXAMPLE: ELECTRIC BASEBOARD HEATER TYPE "H1" CONNECTED TO CIRCUITS 7, 9. TRANSFORMERS. THE TRANSFORMER TYPE IS INDICATED BY A NUMBER FOLLOWING THE UPPER CASE LETTER "T". SEE THE TRANSFORMER SCHEDULE OR THE SINGLE LINE DIAGRAM FOR THE TRANSFORMER DESCRIPTION AND REQUIREMENTS. EXAMPLE: TRANSFORMER TYPE "T1". PANELBOARDS. PANELBOARD DOORS MAY BE SHOWN TO INDICATE OPENING SIDE OF RECESSED PANELBOARDS. SEE PANELBOARD IDENTIFICATION FOR DESIGNATION CODES. SPECIAL NOTE. SEE THE SPECIAL NOTES ON THAT SHEET FOR THE NOTE NUMBER INDICATED IN THE HEXAGON. CONDUIT SHOWN WITHOUT SLASH MARKS SHALL CONTAIN 2 # 12 CONDUCTORS IN 3/4" CONDUIT UNLESS SPECIFIC EQUIPMENT REQUIRES A DIFFERENT SIZE. CONDUIT SHOWN WITH SLASH MARKS SHALL CONTAIN 1 # 12 CONDUCTOR PER SLASH MARK IN 3/4" CONDUIT UNLESS A CONDUCTOR AND CONDUIT SIZE IS SHOWN ADJACENT TO THE SLASH MARKS. SLASH MARK INDICATORS ARE: SHORT STRAIGHT=PHASE CONDUCTOR, LONG STRAIGHT=NEUTRAL CONDUCTOR, SHORT BENT ENDED=SWITCH LEGS, LONG STRAIGHT WITH A DOT=GROUND CONDUCTOR, CHEVRON=CATEGORY 6, HALF CHEVRON=CATEGORY 3, TWIST=SHIELDED TWISTED PAIR, CONCENTRIC CIRCLE AND DOT=COAX CABLE. HOME RUN TO BRANCH CIRCUIT PANELBOARD. THE PANELBOARD DESIGNATION IS SHOWN ADJACENT TO THE HOME RUN ARROW AS A NUMERATOR AND THE CIRCUIT DESIGNATION IS SHOWN AS THE DENOMINATOR. CIRCUIT BREAKER SIZES (AMPS/NUMBER OF POLES) ARE SHOWN IN THE PANELBOARD SCHEDULE WITH THE CORRESPONDING PANELBOARD AND CIRCUIT DESIGNATION. EXAMPLE: HOME RUN TO PANELBOARD LPN-102; CIRCUITS 1, 3, 5. SYMBOL NOTATIONS: UPPER CASE LETTERS ADJACENT TO SYMBOLS INDICATE A UNIT TYPE. SEE APPROPRIATE SCHEDULE OR SPECIFICATIONS. * P2D/I * 2aba LPN-102 1,3,5 FIRE PROTECTION REQUIREMENTS A. PENETRATIONS IN WALLS REQUIRING PROTECTED OPENINGS MUST BE FIRESTOPPED WITH AN APPROVED MATERIAL. 1. CONDUITS MAY PENETRATE WALLS OR PARTITIONS, PROVIDED THEY ARE FIRE-STOPPED. 2. OPENINGS FOR STEEL ELECTRICAL BOXES NOT EXCEEDING 16 SQUARE INCHES ARE PERMITTED PROVIDED OPENINGS DO NOT AGGREGATE MORE THAN 100 SQUARE INCHES FOR ANY 100 SQUARE FEET OF WALL OR PARTITION. 3. OUTLET BOXES ON OPPOSITE SIDES OF WALLS OR PARTITIONS MUST BE SEPARATED BY A HORIZONTAL DISTANCE OF 24 INCHES. B. LIGHT FIXTURES AND OTHER APPARATUS SUPPORTED BY THE ACOUSTICAL CEILING GRID MUST MEET THE REQUIREMENTS OF NEC SECTION 410.16, MEANS OF SUPPORT. C. RECESSED LIGHTING FIXTURES INSTALLED IN FIRE RATED CEILING ASSEMBLIES SHALL BE FIRE RATED FIXTURES BEARING THE UL FIRE RATED LABEL. FIXTURES SHALL BE INSTALLED IN ACCORDANCE WITH THE UL FIRE RESISTANCE DIRECTORY, AND SHALL INCLUDE A FIRE RATED ENCLOSURE INSTALLED OVER THE FIXTURE THAT MEETS THE REQUIREMENTS OF THE UL FIRE RESISTANCE DIRECTORY. SPECIFIC CODE NOTES 19382 P R O F E S S I O N A L E N G I N E E R E R E D E G I S R S T O F A T E W A S H I N G T O N E X E A . D I V A D T FILE: DRAWN BY: CHECKED BY: PROJ. NO: DATE: PACKAGING CORPORATION OF AMERICA 3003 KINGSGATE WAY RICHLAND, WA 99354 BOX MANUFACTURING PLANT 18810 COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED. INDUSTRIAL ENGINEERING, INC MECHANICAL-ELECTRICAL CONSULTANTS 3210 23RD AVE SE RIO RANCHO, NM 87124 WWW.IEINM.COM [email protected]DRAWING NO: FEB 20, 2020 18810 DAE DAE ELECTRICAL PERMIT PLAN SET ASI 002 2019.5.10 FEB 20, 2020 ELECTRICAL CONSTRUCTION PLAN SET REV 3 ASI 11 2019.11.4 FINAL AS-BUILT PLAN SET FEBRUARY 20, 2020 BIM 360://18810 PCA Richland WA Box Plant/18810 PCA Richland-E-V19.rvt 2/21/2020 11:59:37 AM E1.01 ABBREVIATIONS, SYMBOLS, NOTES, & SHEET INDEX Electrical Drawing Index Shell Construction Sheets Sheet Number Sheet Name E1.01 ABBREVIATIONS, SYMBOLS, NOTES, & SHEET INDEX E1.02 OVERALL PLANT ISOMETRIC VIEW E1.03 ELECTRICAL OVERALL SITE PLAN E1.04 ELECTRICAL SITE LIGHTING SOUTH PARKING LOTS E1.05 ELECTRICAL SITE LIGHTING NORTH PARKING LOT E1.06 ELECTRICAL LIGHTING OVERALL LAYOUT E2.01 ELECTRICAL LIGHTING & POWER AREA 1 LB E2.02 ELECTRICAL LIGHTING & POWER AREA 2LC E2.03 ELECTRICAL LIGHTING & POWER AREA 3 LT E2.04 ELECTRICAL LIGHTING & POWER AREA 4 CB E2.05 ELECTRICAL LIGHTING & POWER AREA 5 CC E2.06 ELECTRICAL LIGHTING & POWER AREA 6 CT E2.07 ELECTRICAL LIGHTING & POWER AREA 7 RB E2.08 ELECTRICAL LIGHTING & POWER AREA 8 RC E2.09 ELECTRICAL LIGHTING & POWER AREA 9 RT E3.01 ELECTRICAL & WATER TREATMENT ROOMS ENLARGED VIEWS E3.01A WATER TREATMENT ROOM MEZZANINE LEVEL E3.02 OFICE AREA LIGHTING 1/4" VIEW E3.03 OFFICE AREA POWER 1/4" VIEW E3.04 SHIPPING OFFICE & MID PLANT BATHROOMS 1/ 4" VIEW E3.05 BALER ROOM 1/ 4" VIEW E3.06 COMPRESSOR, BOILER & FIRE PUMP ROOMS 1/4" VIEWS E3.07 ENLARGED BACKFLOW PREVENTOR BUILDING E3.08 ENLARGED MAINTENANCE ROOM ELECTRICAL POWER PLAN E4.01 ELECTRICAL MAIN SWITCHBOARD (MSB) ELEVATIONS E4.02 ELECTRICAL DISTRIBUTION MCC & BSSB ELEVATIONS E5.01 ELECTRICAL MAIN SWITCHBOARD PANEL SCHEDULE E5.02 ELECTRICAL SWITCHBOARD PANEL SCHEDULES E5.02A ELECTRICAL SWITCHBOARD PANEL SCHEDULES E5.03 ELECTRICAL LV PANELBOARD SCHEDULES E5.04 ELECTRICAL LV PANELBOARD SCHEDULES E5.05 ELECTRICAL LV PANELBOARD SCHEDULES E5.06 ELECTRICAL LV PANELBOARD SCHEDULES E5.07 ELECTRICAL LV & LP PANELBOARD SCHEDULES E5.08 ELECTRICAL LP PANELBOARD SCHEDULES E5.08A 480V PANEL SCHEDULES E5.09 EQUIPMENT SCHEDULES E5.10 LIGHT FIXTURE & EQUIPMENT SCHEDULES E5.11 ELECTRICAL EXTERIOR LIGHT FIXTURE SCHEDULE E6.01 EMBEDDED CONDUIT ENDING LOCATIONS E6.02 ELECTRICAL EMBEDDED CONDUITS E6.03 EMBEDDED CONDUIT SCHEDULE E6.04 ADDITIONAL ELECTRICAL EMBEDDED CONDUITS E6.05 ADDITIONAL EMBEDDED CONDUIT SCHEDULE E7.01 CABLE TRAY OVERALL ISOMETRIC VIEW E7.02 CABLE TRAY SYSTEM OVERVIEW E7.03 CABLE TRAY SCHEDULES E7.04 CABLE TRAY SECTIONS E8.01 ELECTRIC SERVICE ENTRANCE LAYOUT E8.01A ELECTRICAL UNDERGROUND UTLITY CONDUITS E8.02 1-LINE DIAGRAM SHEET 1 OF 2 E8.03 1-LINE DIAGRAM SHEET 2 OF 2 E9.01 ELECTRICAL DETAILS E9.02 GROUNDING DETAILS E9.03 GROUNDING CONNECTION DETAILS E9.04 GROUND BAR DETAILS E9.05 GROUNDING OVERALL LAYOUT PLAN Electrical Drawing Index Process Equipment Sheets Sheet Number Sheet Name PE2.10 PROCESS EQUIPMENT OVERALL VIEW PE2.11 ELECTRICAL PROCESS EQUIPMENT AREA 1 LB PE2.12 ELECTRICAL PROCESS EQUIPMENT AREA 2 LC PE2.13 ELECTRICAL PROCESS EQUIPMENT AREA 3 LT PE2.14 ELECTRICAL PROCESS EQUIPMENT AREA 4 CB PE2.15 ELECTRICAL PROCESS EQUIPMENT AREA 5 CC PE2.16 ELECTRICAL PROCESS EQUIPMENT AREA 6 CT PE2.17 ELECTRICAL PROCESS EQUIPMENT AREA 7 RB PE2.18 ELECTRICAL PROCESS EQUIPMENT AREA 8 RC PE2.19 ELECTRICAL PROCESS EQUIPMENT AREA 9 RT PE4.03 MCC ELEVATIONS PE4.04 ELECTRICAL DISTRIBUTION PANELBOARD ELEVATIONS PE5.12 ELECTRICAL SWITCHBOARD PANEL SCHEDULES PE5.13 ELECTIRCAL SWITCHBOARD PANEL SCHEDULES PE5.13A ELECTRICAL MCC PANEL SCHEDULES PE5.14 ELECTRICAL MCC PANEL SCHEDULES PE5.15 PROCESS PANELBOARD SCHEDULES & TRANSFORMER SCHEDULE PE5.16 EQUIPMENT SCHEDULES (PHASE 3 PROCESS CONSTRUCTION) PE8.04 PROCESS EQUIPMENT 1-LINE DIAGRAM SHEET 1 OF 2 PE8.05 PROCESS EQUIPMENT 1-LINE DIAGRAM SHEET 2 OF 2 PE9.06 GROUNDING DETAILS NO DATE REVISION 2 2019.06.18 ASI005 General Elect 6 2019.9.6 Schmitt Add Work #1
LOC LOCATE OR LOCATIONLT LIGHTLTG LIGHTINGLTNG LIGHTNINGLV LOW VOLTAGE
MAX MAXIMUMMAG.S MAGNETIC STARTERM/C MOMENTARY CONTACTMC MECHANICAL CONTRACTORMCB MAIN CIRCUIT BREAKERMCC MOTOR CONTROL CENTERMDC MAIN DISTRIBUTION CENTERMDP MAIN DISTRIBUTION PANELMFR MANUFACTURERMFS MAIN FUSED DISCONNECT
SWITCHMH MANHOLEMIC MICROPHONEMIN MINIMUMMISC MISCELLANEOUSMLO MAIN LUGS ONLYMMS MANUAL MOTOR STARTERMOA MULTIOUTLET ASSEMBLYMSP MOTOR STARTER PANELBOARDMSBD MAIN SWITCHBOARDMT MOUNTMT.C EMPTY CONDUITMTS MANUAL TRANSFER SWITCHMTR MOTOR, MOTORIZED
N.C. NORMALLY CLOSEDNEC NATIONAL ELECTRICAL CODE
NEMA NATIONAL ELECTRICALMANUFACTURER'SASSOCIATION
NFDS NON-FUSED SAFETYDISCONNECT SWITCH
NIC NOT IN CONTRACTNL NIGHT LIGHTN.O. NORMALLY OPENNPF NORMAL POWER FACTORNTS NOT TO SCALE
OH OVERHEADOL OVERLOADS
PA PUBLIC ADDRESSPB PULL BOX OR PUSHBUTTONPE PNEUMATIC ELECTRICPED PEDESTALPF POWER FACTORPH PHASEPIV POST INDICATING VALVEPNL PANELPP POWER POLEPR PAIRPRI PRIMARYPROJ PROJECTIONPRV POWER ROOF VENTILATORPT POTENTIAL TRANSFORMERPVC POLYVINYL CHLORIDE
(CONDUIT)PWR POWER
QUAN QUANTITY
RCPT RECEPTACLEREQD REQUIREDRM ROOMRSC RIGID STEEL CONDUITRTU ROOF TOP UNIT
UC UNDER COUNTERUE UNDERGROUND ELECTRICALUG UNDERGROUNDUH UNIT HEATERUT UNDERGROUND TELEPHONEUTIL UTILITYUV UNIT VENTILATOR OR
ULTRAVIOLET
V VOLTVA VOLT-AMPERESVDT VIDEO DISPLAY TERMINALVERT VERTICALVFD VARIABLE FREQUENCY DRIVEVOL VOLUME
W WATTW/ WITHWG WIRE GUARDWH WATER HEATERW/O WITHOUTWP WEATHERPROOF
XFMR TRANSFORMERXFR TRANSFER
ANGLE@ AT
DELTA' FEET" INCHES# NUMBERØ PHASEC CENTER LINEP PLATE
L
L
EMERGENCY LIGHT FIXTURE
SYMBOL
*** DISTANCE TO HIGHEST OPERABLE PART OF EQUIPMENT
72"** CIRCUIT BREAKER PANEL
SINGLE POLE SW.
DIMMER SWITCH
OCCUPANCY SENSOR SWITCH
PUSH BUTTON
SINGLE RECEPT.
FAN SPEED CONTROL
SPLIT DUPLEX RECEPT/SWITCHED
FOURPLEX RECEPT.
DUPLEX RECEPT.
RECEPT ON EMERGENCY CKT (DUPLEX SHOWN)
ISOLATED GROUND RECEPT (DUPLEX SHOWN)
EQUIPMENT PLUG
RECEPT ON DROP CORD (DUPLEX SHOWN)
RECEPT ON CORD REEL (DUPLEX SHOWN)
FLOOR RECEPT. (DUPLEX SHOWN)
ALL DISTANCES ARE TO CENTER OF DEVICE OR EQUIPMENT UNLESS OTHERWISE NOTED. DEVICES INDICATED AT 48" MAY NOT BE INSTALLED WITH ANY OPERABLE PART HIGHER THAN 48". DEVICES MAY BE INSTALLED IN CONCRETE MASONRY UNITS WITH THE TOP OFTHE DEVICE AT 48".
AS NOTED
* DISTANCE ABOVE TOP OF DOOR FRAME
J
TIMER SWITCH
AS NOTED
48"
3
KEYED SW.
SW. W/PILOT
3-WAY SW.
4-WAY SW.
PER SCHED WALL HEATER (TYPE DENOTED)
** DISTANCE TO TOP OF EQUIPMENT OR DEVICE
PER SCHED D1
H2
HATCHED SYMBOL INDICATES REMOVED
HAND OR HAIR DRYER (TYPE DENOTED)
DASHED SYMBOL INDICATES EXISTING
SOLENOID VALVE AS NOTED
AS NOTED
48"
48"
PER SCHED
48"
AS NOTED
H
T
H1
TC
72"**
72"**
OS
R
72"**
72"**
72"**
72"**
72"**
72"**
72"**
SF-1
T
LIGHT LEVEL SENSOR - TYPE DENOTED
TIME CONTROL SWITCH (TIME SWITCH)
BASEBOARD HEATER (TYPE DENOTED)
HUMIDISTAT
THERMOSTAT
PHOTOCELL
ENCLOSED CIRCUIT BREAKER
RELAY
48"
84"
84"
COMB. MOTOR STARTER (NON-FUSED)
MAG. MOTOR STARTER OR CONTACTOR
SAFETY DISC. SW. (FUSED)
SAFETY DISC. SW. (NON-FUSED)
COMB. MOTOR STARTER (FUSED)
POWER OR DISTRIBUTION PANEL
MOTOR (SEE SCHEDULE)
TRANSFORMER (TYPE DENOTED)
MOTOR HORSEPOWER RATED SWITCH
SPECIAL CABINET (TYPE DENOTED)
48"***
18"
48"
18"
DESCRIPTION
WALL MOUNTED EXTERIOR LIGHT (TYPE DENOTED)
POLE MOUNTED LIGHT (TYPE DENOTED)
RECESSED LIGHT (TYPE DENOTED)
SURFACE OR WALL MTD LIGHT (TYPE DENOTED)
EXIT SIGN (TYPE DENOTED)
SUSPENDED OR PENDANT LIGHT (TYPE DENOTED)
TRACK AND TRACK LIGHT (TYPES DENOTED)
SURFACE LIGHT (TYPE DENOTED)
STRIP LIGHT (TYPE DENOTED)
EMERGENCY BATTERY LIGHT (TYPE DENOTED)
RECESSED LIGHT (TYPE DENOTED)
PER SCHED
AS NOTED
12"*
96"
P2P1
TR1T1T1
E E
EM
H
G
AA
R
HT AFF
AS NOTED
SYMBOL
AS NOTED
AS NOTED
J J
84" A
P
HT AFF
18"
18"
SYMBOL
A
SPECIAL RECEPT. OR CONN. (SEE SCHEDULE)
JUNCTION BOX
PULL BOX
GROUND ROD (PLAN VIEW)
CLOCK (TYPE DENOTED)
POWER POLE (OPEN OFFICE STYLE)
MULTIOUTLET ASSEMBLY (TYPE DENOTED)
MULTIOUTLET ASSEMBLY (TYPE DENOTED)
DESCRIPTION HT AFF
PROJECTOR CONTROL OUTLET
CCTV CAMERA WITH PAN/TILT DRIVE
**** DISTANCE BELOW CEILING
ANTENNA
CCTV CAMERA
***** DISTANCE TO BOTTOM OF DEVICE
144"*
DOOR SIGNAL - APT. UNIT
SPEAKER (WALL OR CEILING MT.)S
MICROPHONE OUTLET
VOLUME CONTROLV
BUZZER
D
BELL
INFORMATION OUTLET (TYPE DENOTED)
WALL TELEPHONE OUTLET (TYPE DENOTED)
INTERCOM OUTLET LOCATION
TELEPHONE OUTLET (TYPE DENOTED)
MULTIPLE SERVICE OUTLET (TYPE DENOTED)
TELEVISION OUTLET
W
CARD READER
ELECTRIC STRIKE
MOTION DETECTOR (TYPE DENOTED)MD
ES
KEYPAD
HEAT DETECTOR (TYPE & TEMP DENOTED)
CONDUIT/WIRE
DESCRIPTION
SMOKE DETECTOR (TYPE DENOTED)
DUCT SMOKE DETECTOR (TYPE DENOTED)R/F135
P
R/F135
F
ELECTRICAL SYMBOL LEGEND
AS NOTED
48"
48"
48"
48"
48"
48"
48"
48"
48"
48"
18"
18"
18"
18"
18"
18"
FOURPLEX RECEPTACLE ON EMERGENCY CIRCUIT18"
4
K
D
OS
T
SP
M
B
PB
VARIABLE FREQUENCY DRIVE
ALS
CP
OCCUPANCY SENSOR - TYPE DENOTED
IC
18"
18"
48"***
84"
18"
18"
OUTLET IN FLOOR (MICROPHONE SHOWN)M
MULTIPLE SERVICE FLR OUTLET (TYPE DENOTED)
CHIME
S
M
P
48"***
48"***
P
P
72"** FIRE ALARM REMOTE ANNUNCIATORFA ANNUN
CR
MAGNETIC LOCKML
IR
CONDUIT SLEEVE (SIZE DENOTED)
1 KEYED NOTE (SEE SCHEDULE)
WIRELESS ACCESS POINTWAP
AS NOTED
DOOR HOLDER
DOOR POWER ASSIST
DC
A2
12b
14E
16c
d
D600
e
1,3,51
SF-1
2,4,6
7,9H1
T1
LPN-102
1
#10
ELECTRICAL SYMBOL NOTESTHE LIGHTING FIXTURE TYPE IS INDICATED BY AN UPPER CASE LETTER.THE CIRCUIT DESIGNATION IS INDICATED BY A NUMBER.THE SWITCH DESIGNATION IS INDICATED BY A LOWER CASE LETTER.
EXAMPLE 1: LIGHTING FIXTURE TYPE "A" IS CONNECTED TO CIRCUIT 12 AND CONTROLLEDBY SWITCH "b".
EXAMPLE 2: THE FIXTURE TYPE SHOWN AS A NUMERATOR INDICATES ALL LIGHTINGFIXTURES IN THE ROOM OR SPACE ARE THE SAME TYPE. THE CIRCUIT NUMBER ANDSWITCH DESIGNATION SHOWN AS A DENOMINATOR INDICATES ALL LIGHTING FIXTURES INTHE ROOM OR SPACE ARE CONNECTED TO THE SAME CIRCUIT, CONTROLLED BY THE SAMESWITCHES, CENTER/OUTBOARD MULTILEVEL SWITCHING.
EXIT LIGHTS. STEM INDICATES WALL MOUNTING. NO STEM INDICATES CEILING MOUNTING.SHADED AREA INDICATES ILLUMINATED FACE(S). ARROW INDICATES DIRECTIONAL ARROWON ILLUMINATED FACE(S). THE CIRCUIT DESIGNATION IS INDICATED BY A NUMBER.EXAMPLE: THE WALL MOUNTED EXIT LIGHT TYPE "E" WITH SINGLE FACE AND DIRECTIONALARROW IS CONNECTED TO CIRCUIT 14.
DEVICES. THE CIRCUIT DESIGNATION IS INDICATED BY A NUMBER. THE SWITCHDESIGNATION IS INDICATED BY A LOWER CASE LETTER. EXAMPLE: SPLIT DUPLEXRECEPTACLE IS CONNECTED TO CIRCUIT 16 AND ONE RECEPTACLE OUTLET ISCONTROLLED BY SWITCH "c".THE CONTROL DEVICE DESIGNATION IS INDICATED BY A LOWER CASE LETTER. EXAMPLE:SINGLE POLE SWITCH "d" TO CONTROL LIGHTING FIXTURES INDICATED BY "d".
WALL BOX DIMMER WITH SIZE AS INDICATED AT DEVICE. EXAMPLE: 600 WATT WALL BOXDIMMER TO CONTROL LIGHTING FIXTURES INDICATED BY "e". SEE SPECIFICATIONS FORWATTAGE IF NOT INDICATED.
SPECIAL CONNECTIONS. THE EQUIPMENT IS INDICATED BY A NUMBER IN A CIRCLE. SEETHE MOTOR AND EQUIPMENT SCHEDULE FOR THE LOAD DESCRIPTION AND TYPE OFCONNECTION. THE CIRCUIT DESIGNATION IS INDICATED BY A NUMBER(S) ADJACENT TOTHE SYMBOL. EXAMPLE: EQUIPMENT NO. 1; 3 PHASE CONNECTION TO CIRCUITS 1, 3, 5.
MOTOR CONNECTIONS. THE MOTOR IS INDICATED BY A NUMBER WITHIN ORCHARACTERS ADJACENT TO THE MOTOR SYMBOL. SEE THE MOTOR AND EQUIPMENTSCHEDULE FOR THE MOTOR DESCRIPTION AND ELECTRICAL REQUIREMENTS. THECIRCUIT DESIGNATION IS INDICATED BY A NUMBER(S) ADJACENT TO THE SYMBOL.EXAMPLE: MOTOR SF-1; 3 PHASE CONNECTION TO CIRCUITS 2, 4, 6.
ELECTRIC HEATER CONNECTIONS. THE HEATER TYPE IS INDICATED BY A NUMBERFOLLOWING THE UPPER CASE LETTER "H". SEE THE HEATER SCHEDULE FORELECTRICAL REQUIREMENTS. THE CIRCUIT DESIGNATION IS INDICATED BY ANUMBER(S) ADJACENT TO THE HEATER. EXAMPLE: ELECTRIC BASEBOARD HEATERTYPE "H1" CONNECTED TO CIRCUITS 7, 9.
TRANSFORMERS. THE TRANSFORMER TYPE IS INDICATED BY A NUMBER FOLLOWINGTHE UPPER CASE LETTER "T". SEE THE TRANSFORMER SCHEDULE OR THE SINGLE LINEDIAGRAM FOR THE TRANSFORMER DESCRIPTION AND REQUIREMENTS. EXAMPLE:TRANSFORMER TYPE "T1".
PANELBOARDS. PANELBOARD DOORS MAY BE SHOWN TO INDICATE OPENING SIDE OFRECESSED PANELBOARDS. SEE PANELBOARD IDENTIFICATION FOR DESIGNATIONCODES.
SPECIAL NOTE. SEE THE SPECIAL NOTES ON THAT SHEET FOR THE NOTE NUMBERINDICATED IN THE HEXAGON.
CONDUIT SHOWN WITHOUT SLASH MARKS SHALL CONTAIN 2 # 12 CONDUCTORS IN 3/4"CONDUIT UNLESS SPECIFIC EQUIPMENT REQUIRES A DIFFERENT SIZE.
CONDUIT SHOWN WITH SLASH MARKS SHALL CONTAIN 1 # 12 CONDUCTOR PER SLASHMARK IN 3/4" CONDUIT UNLESS A CONDUCTOR AND CONDUIT SIZE IS SHOWN ADJACENTTO THE SLASH MARKS. SLASH MARK INDICATORS ARE: SHORT STRAIGHT=PHASECONDUCTOR, LONG STRAIGHT=NEUTRAL CONDUCTOR, SHORT BENT ENDED=SWITCHLEGS, LONG STRAIGHT WITH A DOT=GROUND CONDUCTOR, CHEVRON=CATEGORY 6,HALF CHEVRON=CATEGORY 3, TWIST=SHIELDED TWISTED PAIR, CONCENTRIC CIRCLEAND DOT=COAX CABLE.
HOME RUN TO BRANCH CIRCUIT PANELBOARD. THE PANELBOARD DESIGNATION ISSHOWN ADJACENT TO THE HOME RUN ARROW AS A NUMERATOR AND THE CIRCUITDESIGNATION IS SHOWN AS THE DENOMINATOR. CIRCUIT BREAKER SIZES(AMPS/NUMBER OF POLES) ARE SHOWN IN THE PANELBOARD SCHEDULE WITH THECORRESPONDING PANELBOARD AND CIRCUIT DESIGNATION. EXAMPLE: HOME RUN TOPANELBOARD LPN-102; CIRCUITS 1, 3, 5.
SYMBOL NOTATIONS: UPPER CASE LETTERS ADJACENT TO SYMBOLS INDICATE A UNITTYPE. SEE APPROPRIATE SCHEDULE OR SPECIFICATIONS.
* P2D/I *2aba
LPN-1021,3,5
FIRE PROTECTION REQUIREMENTS
A. PENETRATIONS IN WALLS REQUIRING PROTECTED OPENINGS MUST BE FIRESTOPPED WITH AN APPROVED MATERIAL.
1. CONDUITS MAY PENETRATE WALLS OR PARTITIONS, PROVIDED THEY ARE FIRE-STOPPED.
2. OPENINGS FOR STEEL ELECTRICAL BOXES NOT EXCEEDING 16 SQUARE INCHES ARE PERMITTED PROVIDEDOPENINGS DO NOT AGGREGATE MORE THAN 100 SQUARE INCHES FOR ANY 100 SQUARE FEET OF WALL ORPARTITION.
3. OUTLET BOXES ON OPPOSITE SIDES OF WALLS OR PARTITIONS MUST BE SEPARATED BY A HORIZONTALDISTANCE OF 24 INCHES.
B. LIGHT FIXTURES AND OTHER APPARATUS SUPPORTED BY THE ACOUSTICAL CEILING GRID MUST MEET THEREQUIREMENTS OF NEC SECTION 410.16, MEANS OF SUPPORT.
C. RECESSED LIGHTING FIXTURES INSTALLED IN FIRE RATED CEILING ASSEMBLIES SHALL BE FIRE RATED FIXTURESBEARING THE UL FIRE RATED LABEL. FIXTURES SHALL BE INSTALLED IN ACCORDANCE WITH THE UL FIRE RESISTANCEDIRECTORY, AND SHALL INCLUDE A FIRE RATED ENCLOSURE INSTALLED OVER THE FIXTURE THAT MEETS THEREQUIREMENTS OF THE UL FIRE RESISTANCE DIRECTORY.
SPECIFIC CODE NOTES
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
11:5
9:5
2A
M
E1.02
OVERALL PLANTISOMETRIC VIEW
13D View Overall Plant
NO DATE REVISION
2 2019.06.18 ASI005 General Elect
(E)FO
(E)FO
(E)FO
(E)FO
(E)FO
(E)SIGNSTREET
(E)SIGNCOR
T
(E)XFMR
(E)XFMR
(E)P(E)P
(E)P
(E)P
(E)P
(E)P
(E)P
(E)P
(E)P
(E)P
(E)P
(E)P
(E)P
(E)P
(E)P
(E)P
GV
4"IR
SLV
SLV
SLV
SLV
SLV
SLV
SLV
SLV
SLV
SLV
SLV
SLVSLV
SLV
SLV
SLV
SLV
SLV
SLV
SLV
FP
SIGN
SIGN
SIGN
SIGN
SIGN
SIGN
SIGN
SIGN
SIGN
FH
WV
WV
WV
V19
V19
V19
J
J
J
J
J
J
J
-
1
ELECTRICAL GENERAL NOTES
A. OVERVIEW: ELECTRICAL CONTRACTOR TO PROVIDE 1POWER CONDUIT WITH CONDUCTORS FROM LV-18 TO J-BOXAT SIGNAGE LOCATION AND 1 LOW VOLTAGE 2" CONDUITFROM ADJACENT LV-18 TO J-BOX AT SIGNAGE LOCATION.
B. ELECTRICAL CONTRACTOR TO INSTALL 1 POWER CONDUITWITH CONDUCTORS FROM LV-01 IN ELECTRICAL ROOM TOLV-18 AND ONE 2" CONDUIT FROM IT BACKBOARD INELECTRICAL ROOM TO ADJACENT TO LV-18 AND ADJACENTTO 2" CONDUIT TO SIGNAGE.
ELECTRICAL KEYED NOTES 1
1. ELECTRICAL CONTRACTOR TO PROVIDE 4' POST WITH J-BOXAT END OF (2) 2" CONDUITS. COORDINATE WITH OWNER'SREPRESENTATIVE PRIOR TO ROUGH-IN.
2. ELECTRICAL CONTRACTOR TO PROVIDE ONE (1) 2" CONDUITFROM PANEL LV-18 TO KINGSGATE WAY WITH (4) #10 + (2) #12FROM (2) 20A/1P BREAKERS IN LV-18.
3. ELECTRICAL CONTRACTOR TO PROVIDE ONE (1) 2" CONDUITFROM ADJACENT TO LV-18 TO 4' POST (SEE NOTE 1 ABOVE).
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
0:0
0P
M
E1.03
ELECTRICAL OVERALLSITE PLAN
1" = 50'-0"1
Electrical Site Plan Overall View
NO DATE REVISION
2 2019.06.18 ASI005 General Elect
4 2019.8.9 Misc Electrical
6 2019.9.6 Schmitt Add Work #1
SLV
SLV
SLV
SLV
SLV
SLV
SLV
SLV
SLV
SLV
SLV
SLVSLV
SLV
SLV
SLV
SLV
SLV
FP
SIGN
SIGN
SIGN
SIGN
SIGN
SIGN
WV
(E)SIGNCOR
SLV
V19J
J
PX-04
PX-04
PX-04PX-04
PX-01
PX-01PX-01PX-01PX-01 PX-05PX-05PX-05
PX-11
<unnamed>
ELECTRICAL GENERAL NOTESSCOPE:A. OVERALL SCOPE OF ELECTRICAL WORK CONSISTS OF 3
PHASES.
B. PHASE 1 SHALL BE THE INSTALLATION OF UNDERGROUNDCONDUITS AND SLEEVES DURING FOUNDATION PHASE OFGENERAL CONSTRUCTION.
C. PHASE 2 SHALL BE THE INSTALLATION OF ELECTRICALEQUIPMENT RELATING TO THE BUILDING SHELL ANDPREPARATORY WORK FOR THE INSTALLATION OF THEPROCESS EQUIPMENT. THIS SHALL INCLUDE THEUNDERFLOOR CONDUITS FOR BOTH FACILITY POWER &PROCESS ELECTRICAL, LIGHTING, CABLE TRAY, ELECTRICALSWITCHGEAR AND ASSOCIATED DISTRIBUTIONSWITCHBOARDS, TRANSFORMERS & PANELBOARDS ASSHOWN ON THE SHELL PHASE DRAWINGS.
D. PHASE 3 SHALL BE THE INSTALLATION OF ELECTRICALPOWER DIRECTLY RELATED TO THE ELECTRICAL POWERREQUIRED FOR THE PROCESS EQUIPMENT.
PX-04
PX-04
PX-04
PX-01
PX-01
PX-01
PX-01
PX-01
PX-04
PX-04
PX-07
PX-07
PX-09
PX-09
PX-09
PX-10
PX-11
PX-13
PX-08
PX-08
PX-08
PX-08
PX-08
LP-06/ 10LP-06/ 11
PX-10
PX-10
PX-13
PX-13
PX-16
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
0:0
5P
M
E1.04
ELECTRICAL SITELIGHTING SOUTHPARKING LOTS
1" = 30'-0"1
Site Lighting South West Parking Lot1" = 30'-0"
2Site Lighting South East Parking Lot
1" = 30'-0"3
Site Lighting South Roadway
NO DATE REVISION
2 2019.06.18 ASI005 General Elect
4 2019.8.9 Misc Electrical
SIGN
WV
PX-12PX-12
PX-13
PX-13
PX-16
LP-04/ 10
LP-04/ 11
<unnamed>
ELECTRICAL GENERAL NOTESSCOPE:A. OVERALL SCOPE OF ELECTRICAL WORK CONSISTS OF 3
PHASES.
B. PHASE 1 SHALL BE THE INSTALLATION OF UNDERGROUNDCONDUITS AND SLEEVES DURING FOUNDATION PHASE OFGENERAL CONSTRUCTION.
C. PHASE 2 SHALL BE THE INSTALLATION OF ELECTRICALEQUIPMENT RELATING TO THE BUILDING SHELL ANDPREPARATORY WORK FOR THE INSTALLATION OF THEPROCESS EQUIPMENT. THIS SHALL INCLUDE THEUNDERFLOOR CONDUITS FOR BOTH FACILITY POWER &PROCESS ELECTRICAL, LIGHTING, CABLE TRAY, ELECTRICALSWITCHGEAR AND ASSOCIATED DISTRIBUTIONSWITCHBOARDS, TRANSFORMERS & PANELBOARDS ASSHOWN ON THE SHELL PHASE DRAWINGS.
D. PHASE 3 SHALL BE THE INSTALLATION OF ELECTRICALPOWER DIRECTLY RELATED TO THE ELECTRICAL POWERREQUIRED FOR THE PROCESS EQUIPMENT.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL LIGHTING REVISION NOTESSCOPE:A. ALL LIGHT FIXTURES TO BE PROVIDED BY PCA.
B. LIGHTING PLANS ARE CURRENTLY BASED ON THE LASTEST REVISION SUPPLIED BY THELIGHTING VENDOR. BASIC LIGHT LAYOUT IS FUNDAMENTALLY COMPLETE. EMERGENCYLIGHTS ARE SUBJECT TO FINAL REVIEW AND COORDINATION WITH BUILDING EGRESSPLANS. ALL EMEGENCY AND EXIT LIGHTS SHALL BE CIRCUITED TO THE NEAREST AMBIENTLIGHT CIRCUIT ON AN UNSWITCHED WIRED WITH THE LIGHTS.
C. ALL EXTERIOR, BUILDING MOUNTED LIGHTS TO BE CIRCUITED TO THE NEAREST LIGHTINGPANEL. CIRCUIT LOADING SHALL NOT EXCEED 50% OF CIRCUIT RATING. ALL LIGHTINGBREAKERS SHALL BE 20A/2P/277V BREAKERS IN THE LP SERIES PANELS.
D. ALL EXTERIOR, POLE MOUNTED FIXTURES SHALL BE CIRCUITED ON 277V/2P/20ABREAKERS. CIRCUIT LOADING SHALL BE NO MORE THAN 50% OF CIRCUIT CAPACITY.CIRCUIT CONDUCTORS SHALL HAVE NO MORE THAN 3% VOLTAGE DROP TO THEFURTHEST FIXTURE. FORMAL CIRCUIT PLANS WILL BE PROVIDED PRIOR TO INSTALLATION.
E. ELECTRICAL CONTRACTOR SHALL INSTALL 2 SPARE EMPTY 2" PVC CONDUITS PARALLELWITH EACH LIGHT CIRCUIT CONDUIT FOR FUTURE SECURITY, DATA, OR CAMERAS. EMPTYCONDUITS SHALL HAVE A PULL CORD AND LABELED AT EACH END WITH OPPOSITE ENDDESIGNATION. CONDUITS SHALL BE BROUGHT UP TO 36" ABOVE GRADE AND TERMINATEIN A WEATHERPROOF 4"X4" JUNCTION BOX ATTACHED TO BASE OF POLE OR LIGHT POLE.
F. POLE BASES SHALL BE COORDINATED WITH STRUCTURAL FOR SPECIFIC REQUIREMENTS.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
0:2
3P
M
E1.06
ELECTRICAL LIGHTINGOVERALL LAYOUT
3/64" = 1'-0"1
Lighting Overall View
NO DATE REVISION
2 2019.06.18 ASI005 General Elect
/1 E2.02
AAA A.5 B B.5 C DAA.6
7.5
8
8.5
9
9.5
8.1
A.1 C.6C.3AA.1
LV-03/ 1
DL-07DL-08 DL-09 DL-10
BSSB-1A/ 7BSSB-1B/ 6BSSB-1A/ 5BSSB-1B/ 4
/1 E2.04
B8 C8 D8
EF-2
/1 E2.04
/1 E2.02
1
P02-EM P02P02-EM
P01 P01 P01-EM P02
P02-EM P02 P02-EM P01 P01 P01-EM
P02
P09 P08 PO8-EM
P09 P08 PO8-EM
P01
P01
LV-03/ 12LV-03/ 13
LV-03/ 14 LV-03/ 15
11 1 1
EX1
EX
EX1
EX
EF-3 EF-4EF-5
EF-6
FP/ 1FP/ 3
FP/ 4
FP/ 2
BSSB-1A/ 16
CS-01
BSSB-1A/ 18
CS-02
PX-05PX-05PX-06
PX-01 PX-01 PX-04PX-01 PX-05
LP-01/ 13
SP
ELECTRICAL GENERAL NOTES
1. MOUNT OUTLETS IN PRODUCTION/PROCESS AREA 3'-0"ABOVE FINISHED FLOOR.
2. VERIFY SPECIFIC LOCATION OF ALL EXIT LIGHTS ANDEXTERIOR LIGHTS WITH ARCHITECTURAL PLANS. VERIFYLOCATIONS OF ANY QUESTIONABLE WITH OWNER'SREPRESENTATIVE PRIOR TO ROUGH-IN.
ELECTRICAL KEYED NOTES #
1. Dock Levelers (typical of 4). Install 480V/3P/#10 to dock levelcontroller. Coordinate location with dock level installer. Installdedicated 120V/20A circuit to dock level retainer. Coordinate locationwith dock level installer.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
0:3
1P
M
E2.01
ELECTRICAL LIGHTING &POWER AREA 1 LB
3/32" = 1'-0"1
Lighting & Power AREA 1 - DV-LB
KEYPLAN
N
NO DATE REVISION
1 2019.5.10 Elect Serv & HVAC
2 2019.06.18 ASI005 General Elect
GF
CI
GF
CI
GF
CI
LV-04
/1 E2.03
AREHOUSE AREA 101
MANUFACTURING AREA 100
/1 E2.01
AAA A.5 B B.5 C DAA.6
4
4.5
5
5.5
6
6.5
7
7.5
A.1 C.6C.3AA.1
LV-04/ 2
LV-04/ 1
<unnamed>
LV-04/ 4
LV-04/ 5
LV-04/ 6
LV-04/ 7
LV-03/ 5
/1 E2.04
/1 E2.01
/1 E2.05
B4
C4D4
B5 C5 D5
B6 C6D6
B7 C7 D7
OHF-2
COVERED DOCK111
WAREHOUSEAREA 1
101
TS-04
PO6-EMP-06 P-06
P01 P01-EM P01 P01-EM P02
PO6-EM
P-06 P-06P01 P01-EM P01 P01-EM P02
PO6-EM P-06P01-EM P01 P01-EM P02
PO6-EM P-06 PO6-EMP01 P01 P01-EM P02
PO6-EM P-06 PO6-EMP01 P01 P01-EM P02
PO6-EM P-06 PO6-EMP01 P01 P01-EM P02
P02-EM P02P02-EM
P01 P01 P01-EM P02
P09 P08 PO8-EM
P09 P08 PO8-EM
P09 P08 PO8-EM
P09 P08 PO8-EM
P09 P08 PO8-EM
P09 P08 PO8-EM
P09 P08 PO8-EM
PO6-EMP01
P01
P01
P01
P01
/1 E2.01
LV-04/ 8,10
LV-04/ 9,11
LP-01
TL-01
TL-02
LP-02
LP-01/ 1
LP-01/ 1 LP-01/ 2 LP-01/ 3 LP-01/ 4 LP-01/ 5
LP-01/ 6
LP-01/ 11LP-01/ 10
LP-01/ 8LP-01/ 9
LP-01/ 7
LP-02/ 5LP-02/ 6
LP-02/ 8LP-02/ 9
LP-02/ 10
LP-02/ 11LP-02/ 12
EXEX1
EX
EX1
BSSB-2B/ 5
LP-01/ 12
LV-04/ 3
ELECTRICAL GENERAL NOTES
1. MOUNT OUTLETS IN PRODUCTION/PROCESS AREA 3'-0"ABOVE FINISHED FLOOR.
2. VERIFY SPECIFIC LOCATION OF ALL EXIT LIGHTS ANDEXTERIOR LIGHTS WITH ARCHITECTURAL PLANS. VERIFYLOCATIONS OF ANY QUESTIONABLE WITH OWNER'SREPRESENTATIVE PRIOR TO ROUGH-IN.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
0:3
9P
M
E2.02
ELECTRICAL LIGHTING &POWER AREA 2LC
3/32" = 1'-0"1
Lighting & Power AREA 2 - DV-LC
KEYPLAN
N
NO DATE REVISION
2 2019.06.18 ASI005 General Elect
3 2019.07.17 Misc Updates
GF
CI
GF
CI
LV-07
/1 E2.02
/1 E2.06
AREHOUSE AREA 101
MAU-1
LV-07/ 1
1
AAA A.5 B B.5 C DAA.6
2
1.5
2.5
3
3.5
4
1.1
A.1 C.6C.3AA.1
LV-07/ 5
LV-07/ 4
LV-07/ 3
LV-07/ 2
LV-07/ 6
LV-07/ 7
LV-04/ 4
LV-06/ 9
B2 C2 D2
B3 C3 D3
B4
C4D4
EF-1
TS-07
PO6-EMP-06 P-06 P-06
P02-EM P02 P02 P02
PO6-EM P-06 P-06 P-06P02-EM P02 P02 P02
PO6-EM P-06 P-06P01 P01-EM P01 P01-EM P02
PO6-EM P-06 P-06P01 P01-EM P01 P01-EM P02
PO6-EM P-06 P-06P01 P01-EM P01 P01-EM P02
PO6-EM P-06 P-06P01 P01-EM P01 P01-EM P02
P09 P08 PO8-EM
P09 P08 PO8-EM
P09 P08 PO8-EM
P09 P08 PO8-EM
P09 P08 PO8-EM
P09 P08 PO8-EM
BSSB-2B/ 3
BSSB-2A/ 5
TL-02
LP-02
LP-02/ 1 LP-02/ 2 LP-02/ 3
LP-02/ 4
LP-02/ 5LP-02/ 6
EX1
EX
EX1
EX
EXEX1
BSSB-2B/ 5
PX-04PX-01PX-04
PX-04PX-01
LP-01/ 4
LP-01/ 14
ELECTRICAL GENERAL NOTES
1. MOUNT OUTLETS IN PRODUCTION/PROCESS AREA 3'-0"ABOVE FINISHED FLOOR.
2. VERIFY SPECIFIC LOCATION OF ALL EXIT LIGHTS ANDEXTERIOR LIGHTS WITH ARCHITECTURAL PLANS. VERIFYLOCATIONS OF ANY QUESTIONABLE WITH OWNER'SREPRESENTATIVE PRIOR TO ROUGH-IN.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
1:4
7P
M
E2.03
ELECTRICAL LIGHTING &POWER AREA 3 LT
3/32" = 1'-0"1
Lighting & Power AREA 3 - DV-LT
KEYPLAN
N
NO DATE REVISION
2 2019.06.18 ASI005 General Elect
GF
CI
OS
OS
OSOS
OS
OS
OS
OS
OS
OS
J
J
LV-03
1A
1B
1C
1D
/1 E2.05
/1 E2.07
1E
1F
1G
WATER TREATMENT ROOM 104
LV-10
BSSB-1A
MAU-4
D.5 E E.5 F F.5 G G.5 H H.5
7.5
8
8.5
9
9.5
10
10.5
8.1
9.9
E.9
10.4
10.2
H.1
LV-12
LV-12/ 3
LV-12/ 2
LV-12/ 1
LV-10/ 1
LV-10/ 6
LV-10/ 7
LV-10/ 8
LV-01/ 2
LV-01/ 1
LV-01/ 4
LV-19/ 1
LV-10/ 5
LV-10/ 9
LV-03/ 2
LV-19/ 2
LV-03/ 10
DL-11 DL-12
DL-13
/1 E2.07
D8 E8F8
G8 H8
G9
H9
F10 G10H10
H11
MSB
MCC
ITBACKBOARD
LV-01/ 3
EF-2
EF-7
FC-2
1 2 3 4 5 6
ELECTRICAL108
BOILER ROOM106
SCRAP/BALERROOM
105
2
LV-01/ 5 TS-01
TS-10
P02 P02 P02 P02 P02 P02 P02 P02
P02
P02
P02
P02 P02 P02 P02 P02 P02 P02 P02 P02
P02 P02 P02 P02 P02 P02
P02-EM
P04 P04-EM P05 P05-EM P05 P05 P05 P05
P04 P04-EM P05 P05 P05 P05 P05 P05 P05
P04-EM P04 P05 P05-EM P05-EM P05P05-EM
P05
P07
P07
P07
P07
P07-EM
P07
TS-03
/1 E2.01
/1 E2.01
EUH-1
TF-2
EF-8
TF-4
CU-2 CU-1
EUH-2
OHF-9
LV-02/ 13,15
BSSB-1B/ 10BSSB-1A/ 9
BSSB-1B/ 8
LV-10/ 2
LV-10/ 3LV-10/ 4
1 1 1
FP/ 5
FP/ 6
FP/ 8
FP/ 10
BSSB-1A/ 14
BSSB-1B
LP-06
TL-06
LP-05/ 8
LP-05/ 13
LP-05/ 9
LP-05/ 9,10
LP-06/ 4
LP-06/ 3
EX
EX1
EX
EX1
EX1EX
EX
EX1
EX1
EX
BSSB-1B/ 3
LV-01/ 6,8 LV-01/ 22,24
LP-06/ 2
BSSB-1B/ 17
TF-1 TF-3
EF-14LV-01/ 13
LV-01/ 1
FP/ 7
FP/ 9
FC-1
P07
LV-12/ 1
LV-12/ 4,6,8
P02 P02-EM P02 P02-EM
P02
EX1EX
PX-04
PX-04
PX-01PX-04
PX-02PX-01
PX-01
LP-06/ 8
LP-06/ 9
LV-12
1H
<unnamed>
1
E7.04
K-01
K-02
FP
ELECTRICAL KEYED NOTES 1
1. DOCK LEVELERS (TYPICAL OF 3). INSTALL 480V/3P/#10 TODOCK LEVEL CONTROLLER. COORDINATE LOCATION WITHDOCK LEVEL INSTALLER. INSTALL DEDICATED 120V/20ACIRCUIT TO DOCK LEVEL RETAINER. COORDINATE LOCATIONWITH DOCK LEVEL INSTALLER.
2. IT BACKBOARD. TWO (2) 3" CONDUITS TO IT ROOM 205 WITHPULL CORDS IN BOTH. RISE TO 2" ABOVE BOTTOM OF ITBACKBOARD, CAP WITH PROTECTIVE RING TO PROTECTCABLES. LABEL BOTH ENDS OF CONDUITS. TWO ADDITIONAL4" CONDUITS EXITING BUILDING AND CONTINUING TO EDGEOF SITE FOR CONNECTION TO LOW VOLTAGE PROVIDERS.COORDINATE LOCATION WITH SITE PLAN. PROVIDE PULLCABLES AND LABEL EACH END OF CONDUITS. SEE DETAILSFOR SPECIFICS ON BURIED CONDUITS.
ELECTRICAL GENERAL NOTES
1. MOUNT OUTLETS IN PRODUCTION/PROCESS AREA 3'-0"ABOVE FINISHED FLOOR.
2. VERIFY SPECIFIC LOCATION OF ALL EXIT LIGHTS ANDEXTERIOR LIGHTS WITH ARCHITECTURAL PLANS. VERIFYLOCATIONS OF ANY QUESTIONABLE WITH OWNER'SREPRESENTATIVE PRIOR TO ROUGH-IN.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
1. MOUNT OUTLETS IN PRODUCTION/PROCESS AREA 3'-0"ABOVE FINISHED FLOOR.
2. VERIFY SPECIFIC LOCATION OF ALL EXIT LIGHTS ANDEXTERIOR LIGHTS WITH ARCHITECTURAL PLANS. VERIFYLOCATIONS OF ANY QUESTIONABLE WITH OWNER'SREPRESENTATIVE PRIOR TO ROUGH-IN.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
1. MOUNT OUTLETS IN PRODUCTION/PROCESS AREA 3'-0"ABOVE FINISHED FLOOR.
2. VERIFY SPECIFIC LOCATION OF ALL EXIT LIGHTS ANDEXTERIOR LIGHTS WITH ARCHITECTURAL PLANS. VERIFYLOCATIONS OF ANY QUESTIONABLE WITH OWNER'SREPRESENTATIVE PRIOR TO ROUGH-IN.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
2:0
8P
M
E2.06
ELECTRICAL LIGHTING &POWER AREA 6 CT
3/32" = 1'-0"1
Lighting & Power AREA 6 - DV-CT
KEYPLAN
N
NO DATE REVISION
2 2019.06.18 ASI005 General Elect
3 2019.07.17 Misc Updates
GF
CI
GF
CI
GF
CI
GFCI
GF
CI
GF
CI
GFCI
GF
CI
GFCIGFCI
OS
OSD
OSD
OSD
OS
OS
OS
OS
JJ
OS
OSOS
VS
VS
VS VS
VS
VS
OS
OS
OS
OS
OSD
OSOS
GFCIGFCI
J J
LV-01
LV-02
1A
1B
1C
1D
/1 E2.08
1E
1F
1G
WATER TREATMENT ROOM 104
LV-08
LV-10
LV-11
BSSB-1A
MG.5 H H.5 J J.5 K K.5 L L.5
7.5
8
8.5
9
9.5
10
10.5
8.1
9.9
L.9
M.5
10.4
10.2
H.1 J.3J.4
0.13
0.150.16 0.17
LV-15
LV-14
LV-10/ 6
LV-10/ 7
LV-15/ 2
LV-10/ 8
LV-01/ 2
LV-01/ 1
LV-01/ 4LV-15/ 8
LV-15/ 3
LV-15/ 4
LV-19/ 1
LV-10/ 5
LV-10/ 9
LV-08/ 2 LV-08/ 1
LV-11/ 1
LV-11/ 9
LV-11/ 10
LV-11/ 11
<unnamed>
<unnamed>LV-11/ 2
LV-11/ 4
LV-11/ 3LV-11/ 15
LV-11/ 5
LV-11/ 6
LV-11/ 8
LV-11/ 7
LV-11/ 18
LV-11/ 19
LV-11/ 20
LV-11/ 21
LV-15/ 1
LV-02/ 2
LV-02/ 1
LV-02/ 6
DL-11 DL-12
DL-13
/1 E2.04
LV-14/ 2
LV-14/ 1
G8 H8 J8
K8
L8
M8
G9
H9 J9K9
L9 M9
G10H10
J10 K10
L10
M10
H11 J11
MSB
MCC
ITBACKBOARD
LV-01/ 3
<unnamed>LV-11/ 14
FC-2
FC-6
FC-7
FC-8
ERV-1
LV-08/ 3
1 2 3 4 5 6
BATHROOM207
OFFICE204
Space10
JANITOR210
OFFICE206
WAITING200
HALL208
OFFICE203
BREAK/TRAININGROOM
209CONFERENCE
202
IT ROOM205
WOMEN211
MEN213
ELECTRICAL108
Space31
M LOCKER214
OPEN OFFICE201
SCRAP/BALERROOM
105
FP-1
2
LV-13
1
2
3
4
LV-01/ 5 TS-01
TS-10
TS-08
TS-02
P02 P02
P02
P02 P02 P02 P02 P02 P02 P02 P02-EM
P02 P02 P02 P02 P02 P02 P02 P02 P02 P02 P02-EM
P02 P02 P02 P02 P02 P02 P02 P02
P02
P02 P02-EM
P02
P05 P05 P05 P05 P05-EM
P05 P05 P05 P05 P05
P05-EM P05P05-EM
P05 P05-EM
P07
P07
P07
P07 P-06 P-06
PO6-EMPO6-EMP07-EM
P07
P03 P03 P03
P03 P03-EM P03
P03 P03-EM P03-EM
A A A A
A1
A A
A A1
A
A1
A
A A1 A A1 A
A1 A1 A
A
A
AA
A1
AA
AA
AAA1A1
A1 A1
AAA
A
A1
A
A1
A1
AA A
A
A1
A
AA
A1A
A
TF-2 TF-4TF-5
FC-9
FC-10 FC-11
FC-12
CU-4
EUH-3
CU-2 CU-1
EUH-5
EUH-4
LV-11/ 26,28
LV-11/ 29,31
LV-11/30,32,34
EUH-2
BC-1
OHF-8OHF-9
LV-02/ 12,14
LV-02/ 13,15
BSSB-1B/ 10BSSB-1A/ 9
BSSB-1B/ 8
LV-10/ 2
LV-10/ 3LV-10/ 4
1 1 1
FP/ 8
FP/ 10
FP/ 11
BSSB-1B/ 11
LV-15/ 2
BSSB-1B
LP-06
TL-06
LP-05/ 8LP-05/ 7
LP-05/ 13
LP-05/ 9
LP-05/ 9,10
LP-06/ 4
LP-06/ 3
EX EX1
EX EX1
EX1
EX
EX
EX1
EX1
EX
EX1
EX EX
EX1
LV-01/ 6,8 LV-01/ 22,24
LP-06/ 2
BSSB-1B/ 17
BSSB-1B/ 9
BSSB-1A/ 10
EWH-1 EWH-2
LP-06/ 5
TF-3 TF-6
EF-14LV-01/ 13
LV-01/ 1
FP/ 7
FP/ 9
FP/ 12
FC-1
P07
LV-15/10,12,14
LV-14/ 3,5,7
P02
P02
<unnamed>
P02-EMP02-EM
P02
P02-EMP02-EM P02 P02-EM
P02
P02-EM
BSSB-1A/ 20
BSSB-1A/ 4
CS-07 CS-06
PX-04
PX-02PX-01
PX-01
PX-02
PX-01
EX
EX1 PX-04PX-04
PX-04
PX-01
PX-01
PX-01
PX-01
PX-01
LP-06/ 8
LP-06/ 9
LP-05/ 14
PX-04
1H
1
E7.04
FP
ELECTRICAL GENERAL NOTES
1. MOUNT OUTLETS IN PRODUCTION/PROCESS AREA 3'-0"ABOVE FINISHED FLOOR.
2. VERIFY SPECIFIC LOCATION OF ALL EXIT LIGHTS ANDEXTERIOR LIGHTS WITH ARCHITECTURAL PLANS. VERIFYLOCATIONS OF ANY QUESTIONABLE WITH OWNER'SREPRESENTATIVE PRIOR TO ROUGH-IN.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
2:1
9P
M
E2.07
ELECTRICAL LIGHTING &POWER AREA 7 RB
3/32" = 1'-0"1
Lighting & Power AREA 7 - DV-RB
KEYPLAN
N
NO DATE REVISION
1 2019.5.10 Elect Serv & HVAC
2 2019.06.18 ASI005 General Elect
/1 E2.07
/1 E2.09
PALLET STORAGE 110
MJ J.5 K K.5 L L.5
4.5
5
5.5
6
6.5
7
L.9
M.5 NM.9
5.4
7.1
LV-09/ 9
LV-09/ 8
LV-02/ 5
LV-02/ 3LV-02/ 4
DL-03
DL-04
DL-05
DL-06
BSSB-2A/ 13
BSSB-2A/ 14
BSSB-2A/ 15
BSSB-2A/ 16
/1 E2.05
J4K4 L4
M4
J5L5
K5
M5
J6 K6 L6M6
J7 K7 L7
M7
PALLET STORAGE110
P02 P02 P02 P02 P02 P02 P02 P02-EM
P02 P02 P02 P02 P02 P02 P02 P02-EM
P01 P02 P02 P02 P02 P02 P02 P02-EM
P01 P02 P02 P02 P02 P02 P02 P02-EM
P01-EM P02 P02 P02 P02 P02 P02 P02-EM
P01 P02 P02 P02 P02 P02 P02 P02-EM
P02 P02 P02 P02 P02 P02 P02 P02-EM
PO6-EM PO6-EM
P-06P-06
PO6-EM PO6-EM
GUH-3
OHF-9
OHF-6
LV-09/ 10,12
LV-09/ 11,13
LV-02/ 8,10
LV-02/ 9,11
LV-09/ 4
LV-09/ 6
LV-09/ 14
LV-09/ 15
LV-09/ 16
LV-09/ 17
1
1
1
1
1
LV-02/ 7
<unnamed>
LP-03/ 11
LP-03/ 13
LP-05/ 4
LP-05/ 5
LP-05/ 6
EX1
EX
EX1EX
EX1
EX
PX-01
PX-01
PX-04
PX-04
PX-01
PX-03
PX-01
PX-05
LP-05/ 12
SUPERVISOR'S OFFICE
4
ELECTRICAL GENERAL NOTES
1. MOUNT OUTLETS IN PRODUCTION/PROCESS AREA 3'-0"ABOVE FINISHED FLOOR.
2. VERIFY SPECIFIC LOCATION OF ALL EXIT LIGHTS ANDEXTERIOR LIGHTS WITH ARCHITECTURAL PLANS. VERIFYLOCATIONS OF ANY QUESTIONABLE WITH OWNER'SREPRESENTATIVE PRIOR TO ROUGH-IN.
ELECTRICAL KEYED NOTES
1. DOCK LEVELERS (TYPICAL OF 6). INSTALL 480V/3P/#10 TODOCK LEVEL CONTROLLER. COORDINATE LOCATION WITHDOCK LEVEL INSTALLER. INSTALL DEDICATED 120V/20ACIRCUIT TO DOCK LEVEL RETAINER. COORDINATE LOCATIONWITH DOCK LEVEL INSTALLER.
#
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
2:2
6P
M
E2.08
ELECTRICAL LIGHTING &POWER AREA 8 RC
3/32" = 1'-0"1
Lighting & Power AREA 8 - DV-RC
KEYPLAN
N
NO DATE REVISION
2 2019.06.18 ASI005 General Elect
GF
CI GFCI
GF
CI
GF
CI
OSD
OS
OS
OSD
LV-05
LV-09
/1 E2.06
/1 E2.08
1
MJ J.5 K K.5 L L.5
2
1.5
2.5
3
3.5
4
1.1
L.9
LV-09/ 3
LV-09/ 2
LV-05/ 1LV-05/ 3
LV-05/ 4
LV-05/ 5
LV-05/ 6
LV-05/ 7
LV-05/ 8
LV-05/ 9
LV-05/ 11
LV-05/ 10
LV-09/ 5
LV-09/ 7
LV-05/ 17
LV-05/ 12
LV-05/ 13
LV-05/ 14
LV-05/ 15
LV-05/ 18LV-05/ 16
DL-01
DL-02BSSB-2A/ 12
BSSB-2A/ 13
J2 K2 L2
M2
J3 K3 L3
M3
J4K4 L4
M4
MAU-3
OHF-4
ERV-2GUH-2CLOSET
301
DRIVER'SLOUNGE
302
SHIPPING OFFICE300
RESTROOM303
1
TS-05
TS-09
P02 P02 P02 P02 P02 P02-EM
P02-EM P02-EM P02-EM P02 P02-EM P02
P02 P02 P02 P02 P02 P02
P02 P02 P02 P02 P02 P02
P02 P02 P02 P02 P02 P02 P02 P02
P02-EM
P02
P02
P02
P02
P02-EM
P02-EM
P02
P02 P02 P02 P02 P02 P02 P02 P02-EM
A AA
A A1 A A A1 A A
AA1
A
CU-3
EF-10
LV-05/ 21,23
LV-05/ 22
LV-05/ 24
LV-05/ 25,27
LV-09/ 10,12
LV-09/ 1
LV-09/ 4
LV-09/ 6
1
1
1
BSSB-2A/ 6
BSSB-2A/ 21
LP-04/ 8
LP-04/ 7
BSSB-2A/ 11
<unnamed>
EX1EX
EX1EX
EX
EX1
EX
EX1
EF-9
LV-05/ 20
BSSB-2A/ 8
CS-03
BSSB-2A/ 9
CS-04 CS-05
BSSB-2A/ 10
EX1EX
PX-01
PX-01
PX-05
PX-01
PX-01PX-04PX-04PX-01
LP-04/ 3
LV-09/ 18,20
SUPERVISOR'S OFFICE
4
ELECTRICAL GENERAL NOTES
1. MOUNT OUTLETS IN PRODUCTION/PROCESS AREA 3'-0"ABOVE FINISHED FLOOR.
2. VERIFY SPECIFIC LOCATION OF ALL EXIT LIGHTS ANDEXTERIOR LIGHTS WITH ARCHITECTURAL PLANS. VERIFYLOCATIONS OF ANY QUESTIONABLE WITH OWNER'SREPRESENTATIVE PRIOR TO ROUGH-IN.
ELECTRICAL KEYED NOTES
1. DOCK LEVELERS (TYPICAL OF 6). INSTALL 480V/3P/#10 TODOCK LEVEL CONTROLLER. COORDINATE LOCATION WITHDOCK LEVEL INSTALLER. INSTALL DEDICATED 120V/20ACIRCUIT TO DOCK LEVEL RETAINER. COORDINATE LOCATIONWITH DOCK LEVEL INSTALLER.
2. N/A3. 2" DATA CONDUIT FROM IT ROOM 205. RISE TO 2" ABOVE
BOTTOM OF IT BACKBOARD. CAP WITH PROTECTIVE RING TOPROTECT CABLES. PROVIDE PULL CORD AND LABLE BOTHENDS OF CONDUIT.
4. PROVIDE 200A DISCONNECT AND CIRCUIT FROM PANEL LV-09WITH 1 1/2"C,(3) #1 THHN + #6 GND. MOUNT DISCONNECT TOCOLUMN J4. PROVIDE FEED FROM DISCONNECT TOSUPERVISOR'S OFFICE 125A PANEL.
#
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
2:3
3P
M
E2.09
ELECTRICAL LIGHTING &POWER AREA 9 RT
3/32" = 1'-0"1
Lighting & Power AREA 9 - DV-RT
KEYPLAN
N
NO DATE REVISION
1 2019.5.10 Elect Serv & HVAC
2 2019.06.18 ASI005 General Elect
6 2019.9.6 Schmitt Add Work #1
LV-08
LV-15
LV-15/ 2
LV-15/ 3
LV-15/ 4
LV-15/ 1
P03
P03
P03-EMP03
P03-EM
P03-EMP03
P03P03
EX1
EX
BSSB-1A/ 19
SUP-2
LV-15/ 6
3
P11P11
P11
P11
P11
P11
P11
P11
LP-06/ 14
LV-01
1A1B1C1D1E1F1GBSSB-1A
LV-10/ 7
LV-01/ 2
LV-01/ 1
LV-01/ 4
MSB
DL-13
FC-2
LV-01/ 5LV-01/ 3
P07P07
P07-EM
P07P07 P07
TS-01
IT BACKBOARD
MSB-1A MSB-1B MSB-1C MSB-1D MSB-1E MSB-1F MSB-1G
MCC-1 1110
CU-2 CU-1
EUH-2
SHELLBETTER CABINET
UTILITY TRANSFORMERWITH VAULT BENEATH
LP-06/ 2
LP-06/ 7
1
1
1
UTILITY TRANSFORMERVAULT FOR FUTURETRANSFORMER
EX
EX1
LV-01/ 6,8
LV-01/ 22,24
BSSB-1A/ 1
LV-01/ 13
LV-01/ 25,27
FC-1
22
2
PLC
CA
BIN
ET
SC
RA
PS
YS
TE
M
1
E7.04
FP
LP-06
1H
VFD-1
VFD-2
MSB-1C/ 2
MSB-1F/ 5
1. PROVIDE 4" HOUSE KEEPING PAD FOR EQUIPMENTS ASSHOWN ON PLAN. EQUIPMENT PAD TO EXTEND 6" BEYONDEACH END OF EQUIPMENT AND EXTEND 3" BEYOND FRONTOF EQUIPMENT. CONTRACTOR TO VERIFY EXACT LOCATIONAND DIMENSIONS OF EQUIPMENT PRIOR TO INSTALLATIONOF THE EQUIPMENT PADS. WHERE EQUIPMENT IS LOCATEDAWAY FROM A WALL THE PAD SHALL EXTEND 3" BEYONDFRONT AND REAR OF EQUIPMENT.
2. SEE CIVIL ENGINEERING PLANS FOR EXTENSION OFELECTRICAL UTILITY, DATA, AND SIGNAGE CONDUITEXTENDED TO THE STREET. CONTRACTOR TO INSTALLELECTRIAL VAULT IN UTILITY CONDUITS AT EXIT TO PARKINGLOT PER CIVIL PLANS. ELECTRICAL CONDUITS TO BE IN DUCTBANK WHEN PASSING UNDER DRIVE OR VEHICLE PATH.
3. INK KITCHEN CONTROL CONSOLE RECEPTACLES.COORDINATE WITH INK KITCHEN CONTRACTOR FORSPECIFIC LOCATION OF RECEPTACLES. PROVIDE 4X4 J-BOXWITH CONDUIT BACK TO IT ROOM IN MAIN OFFICE AREA.
ELECTRICAL KEYED NOTES # ELECTRICAL GENERAL NOTES
1. LIGHTING FOR THE WATER TREATMENT ROOM SHALL BECIRCUITED FROM THE OVERALL PRODUCTION AREALIGHTING PANELS AND SHALL BE SWITCHED WITH THEOVERALL PRODUCTION AREA LIGHTING.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
2:4
8P
M
E3.01
ELECTRICAL & WATERTREATMENT ROOMSENLARGED VIEWS
1/4" = 1'-0"1
Water Treatment Room Enlarged View
MCC
1/4" = 1'-0"2
Electrical Room Enlarged View
KEYPLAN
N
NO DATE REVISION
1 2019.5.10 Elect Serv & HVAC
2 2019.06.18 ASI005 General Elect
4 2019.8.9 Misc Electrical
5 2019 Misc Electrical
6 2019.9.6 Schmitt Add Work #1
J J.5 K
9
9.5
10
9.9
J.3J.4
J KJ.5
9
10
9.5
9.9
K.1J.4
J J.5 K
9
9.5
109.9
J.6J.3J.4J J.5 K
9
9.5
109.9
J.6J.3J.4
P03
P03
P03-EM P03-EM
P03P03-EM
P03P03
P03
LV-15/ 11
LV-15/ 13
ELECTRICAL GENERAL NOTES
1. LIGHTING FOR THE MEZZANINE AREA IS SHOWN ON SHEETE3.07 AND IS PART OF THE GENERAL PRODUCTION AREALIGHTING. CIRCUITING AND SWITCHING FOR THE MEZZANINEAREA SHALL BE BASED ON THE OVERALL PRODUCTION AREAWITH NO SPECIFIC CIRCUITING OR SWITCHING FOR THEMEZZANINE AREA.
2. RECEPTACLES FOR THE MEZZANINE AREA SHALL BE ASSHOWN ON THIS PLAN.
3. FRAMING FOR THE FLOOR OF THE MEZZANINE IS SHOWNFOR REFERANCE ONLY AND HAS NO RELATIONSHIP TOLIGHTING LAYOUT.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
2:4
9P
M
E3.01A
WATER TREATMENTROOM MEZZANINELEVEL
1/8" = 1'-0"1
Water Treatment area mezzanine
NO DATE REVISION
6 2019.9.6 Schmitt Add Work #1
OS
OSD
OSD
OSD
OS
OS
OS
OS
OS
OSOS
VS
VS
VS VS
VS
VS
OS OS
OS
OS
OSD
OSOS
MK K.5 L L.5
9
9.5
10
9.9
L.9
K L MK.5 L.5
9
10
9.5
L.9
9.9
K.1
BREAK/TRAININGROOM
209CONFERENCE
202
OPEN OFFICE201
BATHROOM207IT ROOM
205
OFFICE204
OFFICE206
WOMEN211
MEN213
M LOCKER214
HALL208
JANITOR210
A A A A
A1
A A
A A1
A
A1
A
A A1 A A1A
A1 A1 A
A
A
AA
A1
AA
AA
A
AA1A1
A1 A1
AAA
A
A1
A
A1
A1
A
A A
A
A1
A
AA
A1A
A
LV-11/ 22
LV-11/ 23
LV-11/ 25LV-11/ 24
EX
EX1
201.2
EX
A
1. LIGHT FIXTURES LOCATED OVER RESTROOMS, LOCKERROOMSAND JANITOR CLOSETS TO BE RECESSED MOUNTEDIN HARD GWB CEILING. PROVIDE HARDWARE AS REQUIREDFOR FLUSH MOUNTING.
2. BATHROOMS AND LOCKER ROOMS SHALL HAVE A DRYWALLCEILING. OWNER WILL PROVIDE AN ADAPTER KIT TO ALLOWDESIGNATED FIXTURES TO BE DRYWALL MOUNTED.COORDINATE SPECIFIC KIT REQUIREMENTS WITH FIXTUREMANUFACTURER TO ASSURE FIT.
ELECTRICAL LIGHTING GENERAL NOTES
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
2:5
3P
M
E3.02
OFICE AREA LIGHTING1/4" VIEW
KEYPLAN
N
1/4" = 1'-0"1
Electrical Lighting Plant Office Area 1/4" View
NO DATE REVISION
2 2019.06.18 ASI005 General Elect
7 2019.10.7 Misc Electrical
GF
CI
GF
CI
GF
CI
GFCI
GF
CI
GF
CI
GFCI
GF
CI
J J
GFCIGFCI
JJ
1. TOTAL OF 3 CONDUITS TO RISE AT BOTTOM OF IT BACKBOARD TO 12" AFF. CAP WITHPROTECTIVE RING TO PROTECT CABLES. TWO (2) 3" CONDUITS, WITH PULL CORDS FROM ITBACKBOARD IN ELECTRICAL ROOM. ONE (1) 2" CONDUIT TO CLOSET IN SHIPPING OFFICES.PROVIDE PULL CORD.
2. PROVIDE TWO (2) 4"X4" J-BOXS WITH 3/4" CONDUIT TO PANEL LV-18. PROVIDE FOUR (4) #10THHN CU CONDUCTORS + #10 GND IN EACH & LABEL EACH AT EACH END. PROVIDE ENOUGHEXCESS TO TERMINATE TO ANY BREAKER IN LV-18 AND FOR CONNECTION TO WHIP FORPOWER TO SERVER CABINET.
3. IT RACK BY OTHERS.4. PROVIDE IN-FLOOR LOW VOLTAGE BOX. PROVIDE 1" CONDUIT UNDERFLOOR TO RISE AT
BASE OF IT BACK BOARD IN IT ROOM.5. PROVIDE DUPLEX RECEPTACLE AND LOW VOLTAGE RECEPTACLE AT 60" AFF. COORDINATE
LOCATION WITH OWNER'S REPRESENTATIVE PRIOR TO ROUGH IN.6. PROVIDE J-BOX ABOVE CEILING WITH 3/4" CONDUIT TO CEILING ABOVE IT ROOM 205.
COORDINATE LOCATION IN IT ROOM WITH OWNER'S REPRESENTATIVE. PROVIDE J-BOXABOVE CEILING WITH 1"C & (6) #10 THHN CU (3 BLK + 3 WHITE) PLUS (2) #10 GND BACK TO 3PBREAKER IN PANEL LV-11. COORDINATE WITH FURNITURE PROVIDER.
ELECTRICAL KEYED NOTES #
MK K.5 L L.5
9
9.5
10
9.9
L.9
K L MK.5 L.5
9
10
9.5
L.9
9.9
K.1
LV-11
LV-11/ 1
LV-11/ 9
LV-11/ 10
LV-11/ 11
LV-11/ 2
LV-11/ 4
LV-11/ 3
LV-11/ 15
LV-11/ 5
LV-11/ 6
LV-11/ 8
LV-11/ 7
LV-11/ 18
LV-11/ 19
LV-11/ 20
LV-11/ 21
LV-11/ 27
LV-11/ 14
BREAK/TRAININGROOM
209
CONFERENCE202
OPEN OFFICE201
BATHROOM207
IT ROOM205
OFFICE204
OFFICE206
WOMEN211MEN
213
M LOCKER214
HALL208
JANITOR210
FC-6
FC-7
FC-8
LV-13
1
2
3
4
1
25
IT RACK
6
FC-10
FC-11
FC-12FC-9
ERV-1
BC-1
4 4
3
55
LV-11/ 16
LV-11/ 26,28
LV-11/ 29,31
4 4 4
LV-11/ 33
LV-11/ 35
LV-11/ 37
FC-3
EWH-2
EWH-1
LV-11/36,38,40
LV-11/30,32,34
LV-11/ 39
LV-11/ 41
LV-11/ 12
11
12
7,9 8,10
LV-11/ 17
LV-11/ 13
LV-11/ 42
LV-11/43,45,47
LV-11/44,46,48
6 6
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
ELECTRICAL CONSTRUCTION PLAN SETREV 3 ASI 11 2019.11.4
FINAL AS-BUILT PLAN SETFEBRUARY 20, 2020
BIM
36
0://1
88
10
PC
AR
ich
land
WA
Bo
xP
lant/1
88
10
PC
AR
ich
lan
d-E
-V1
9.r
vt
2/2
1/2
020
12:0
3:2
7P
M
E3.06
COMPRESSOR, BOILER& FIRE PUMP ROOMS1/4" VIEWS
1/4" = 1'-0"1
Compressor & Fire Pump Rooms Enlarged View1/4" = 1'-0"
2Boiler Room Enlarged View
KEYPLAN
N
NO DATE REVISION
3 2019.07.17 Misc Updates
OS
GFCI
GFCI
GF
CI
GFCI GFCI
A
A
2 2
LV-18/ 1
LV-18/ 2
LV-18
1
LV-18/ 3
H-01 H-02
LV-18/ 5
3 3
LV-18/ 4
ELECTRICAL KEYED NOTES #
1. ELECTRICAL CONTRACTOR TO INSTALL FULL BUILDINGGROUND INCLUDING BONDING TO WATER LINE, TYING TOREBAR IN FOOTING OR PAD, & 10' GROUND ROD.
2. CONTRACTOR TO SUPPLY 1X4 LENSED LED STRIP LIGHTS.COLLUMBIA CSL4-4035 4' LED STRIPLIGHT, 4,000 LUMENS,3500K 40W OR EQUAL AND APPROVED.
3. INSTALL DEDICATED GFCI RECEPTACLE FOR CONNECTIONTO HEATERS. HANG HEATERS ON FACTORY PROVIDED PLATEAND PLUG INTO GFCI RECEPTACLE.
ELECTRICAL GENERAL NOTES1. ELECTRICAL CONDUCTORS TO BE (4) 1/0 COPPER WITH #2
EGC FEEDING PANEL LV-18.2. ELECTRICAL CONTRACTOR TO GOUND PER NEC 250 WITH
SPECIFIC ATTENTION TO REQUIREMENTS FOR EGCCONNECTION AT THE BUILDING. SPECIFIC QUESTIONSREGARDING GROUNDING SHALL BE DIRECTED TO THE SITEELECTRICAL ENGINEER.
3. ELECTRICAL CONTRACTOR TO RUN DEDICATED 2" PVCCONDUIT IN UTILITY TRENCH FROM PANEL LV-01 WITH NEW60A BREAKER IN ELECTRICAL ROOM TO BACKFLOWPREVENTER CABINET ELECTRICAL PANEL LV-18. PANEL LV-18TO BE MOUNTED ON FREE STANDING UNISTRUT FRAMEAPPROXIMATELY 18" ADJACENT TO DOGHOUSE. ELECTRICALCONDUITS FROM PANEL LV-18 TO DOGHOUSE SHALL BEUNDERGROUND FROM THE PANEL TO THE DOGHOUSE, RISEOUTSIDE THE DOGHOUSE AND PENETRATE THE DOGHOUSEWALL AT APPROXIMATELY 12" ABOVE GRADE. ELECTRICALCONDUITS TO BE 3/4" MINIMUM.
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
H-01 ELECTRIC HEATER LV-18 120 V 1 15 A 20 A 3/4"C,(2) #10 + GND 30 Elect Contractor
H-02 ELECTRIC HEATER LV-18 120 V 1 15 A 20 A 3/4"C,(2) #10 + GND 30 Elect Contractor
1/2" = 1'-0"2
Backflow Preventer Cabinet Enlarged Electrical Power Plan
NO DATE REVISION
4 2019.8.9 Misc Electrical
/1 E2.04
LV-12
BSSB-1B/ 18
EF-8
LV-03/ 10
TS-11
LV-19/ 1
LV-19/ 2
LV-19/ 3
LV-19/ 4
LV-19/ 5
LV-19/ 6LV-19/ 7LV-19/ 8
LV-19/ 10
MRP/ 7,9,11
LV-19/ 11LV-19/12,14,16
DRILL PRESS
BAND SAW
GRINDER
WE;LDING AREA
LV-19/ 15LV-19/ 17
BEAD BLASTSOLVENTTANK
LV-19/ 18,20
LV-19/ 19,21
1
1
1
1 1
1
22 2
2 2
2
2
2
2
2
3
3
WEF-01
LV-19/23,25,27
MRP/ 2,4,6
MRP/8,10,12
K-01
K-02
MRP
LV-19
MRP/ 1,3,5
4
4
ELECTRICAL KEYED NOTES #
1. SPECIAL EQUIPMENT RECEPTACLE. PROVIDE 4"X4" J-BOXWITH 3 HOTS AND 1 NEUTRAL REGARDLESS OF SPECIFICRECEPTACLE REQUIREMENT. COORDINATE RECEPTACLEWITH OWNER'S REPRESENTATIVE PRIOR TO ORDERING.
2. INSTALL RECEPTACLES IN 4"X4" J-BOX WITH 3/4" CONDUITBETWEEN. INSTALL AT 9" ABOVE WORK BENCH, OR ASINSTRUCTED BY OWNER'S REPRESENTATIVE . COORDINATEWITH OWNER'S REPRESENTATIVE PRIOR TO ROUGH-IN.
3. PROVIDE 100A FUSED DISCONNECT WITH FUSES. AMPERAGEOF FUSES TO BE DETERMINED BY OWNER. PROVIDE 1"CONDUIT BACK TO PANEL WITH (4) #3 THHN + #8 GND.
4. PROVIDE A 480V/3P/30 DISCONNECT MOUNTED AT 48' AFF.CORDINATE EXACT LOCATION WITH OWNER'SREPRESENTATIVE PRIOR TO ROUGH-IN.
ELECTRICAL GENERAL NOTES
1. INSTALL A DEDICATED GROUND FOR EACH CIRCUIT BACK TOELECTRICAL PANEL. CONDUIT IS NOT TO BE RELIED UPONFOR GROUND.
2. MINIMUM SIZE CONDUIT FOR POWER RUNS IN MAINTENANCEROOM SHALL BE 1" UNLESS SPECIFICALLY AUTHORIZED.
3. PROVIDE 12 SPARE 20A/1P BREAKERS IN PANEL LV-19.4. FOR ELECTRICAL LOADS ON SOUTH AND WEST WALLS OF
THE MAINTENANCE AREA THE CONTRACTOR SHALL ROUTECONDUITS FROM PANELS "MRP" AND "LV-19" UP AND ALONGTHE WALL IMMEDIATELY BENEATH THE PIPE RACK,DROPPING SURFACE DOWN THE WALL TO THE LOCATION OFTHE ELECTRICAL DEVICE. CONDUIT SHALL BE SUPPORTEDBY UNISTRUT. JUNCTION BOXES, DISCONNECTS ANDDEVICES SHALL BE RIGIDLY ATTACHED TO THE WALL TOWITHSTAND TYPICAL MAINTENANCE AREA USE. CONDUITSMAY BE RUN HORIZONTALLY ALONG WALL BETWEENADJACENT DEVICES. 480V AND 208V CONDUCTORS SHALLNOT BE INCORPORATED IN THE SAME CONDUIT.
5. FOR ELECTRICAL LOADS ON THE NORTH EAST AND NORTHAREAS OF THE MAINTENANCE AREA THE CONTRACTORSHALL ROUTE
19382
PRO
F E S S I ONAL ENG I NE
ER
E R EDE G I SR
ST
OF
ATEWASHINGTON
EXEA.DIVAD
T
FILE:
DRAWN BY:
CHECKED BY:
PROJ. NO:
DATE:
PACKAGING CORPORATION OF AMERICA
3003 KINGSGATE WAYRICHLAND, WA 99354
BOX MANUFACTURING PLANT
18810
COPYRIGHT 2019 BY INDUSTRIAL ENGINEERING, INC. ALL RIGHTS RESERVED.
![Compact and Discreet - yaesu.ru · Battery Life [5-5-90 duty with battery saver]MDC-1200® Features: - MDC-1200® ANI - MDC-1200® Call Alert - MDC-1200® Sel Call - MDC-1200® Radio](https://static.documents.pub/doc/80x56/5e80d3de6005c20fb639820d/compact-and-discreet-yaesuru-battery-life-5-5-90-duty-with-battery-savermdc-1200.jpg)
