ELEVEN COLLABORATIVECONFERENCE TOPS
Assembly Instructions
ELEVEN COLLABORATIVE CONFERENCE TOPSAssembly Instructions
Table of Contents
SUPPORT BRACE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TABLE BASE FRAME ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
LEG ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
TOP JOINING PLATE ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TOP CLAMP/TOP SPACER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TOP PLACEMENT AND CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TOP ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3Completed Assembly
Outside Leg Rail
Support Brace
Flat Head Cap Screw
SUPPORT BRACE ASSEMBLY(This step is not used on all tables)
Position Support Brace so counter-sunk holesin Outside Leg Insert rail are aligned with holeson end of Support Brace.
Insert Flat Head Cap Screws and tighten with5MM allen wrench.
NOTE: Frame is assembled upside-down. Frameis to be flipped over after legs are installed.
NOTE: This step is used only on trapezoid tablesand some boat-shaped tables.
ELEVEN COLLABORATIVE CONFERENCE TOPSAssembly Instructions
Support Brace AssemblyTHIS STEP IS NOT USED ON ALL TABLES
NOTE: Frame is assembled upside-down .Frame is to be flipped over after legs are installed .
NOTE: This step is used only on trapezoid tables and some boat-shaped tables .
Instructions
• Position Support Brace so counter-sunk holes in Outside Leg Insert rail are aligned with holes on end of Support Brace .
• Insert Flat Head Cap Screws and tighten with 5MM allen wrench .
4
Double Top Support Rail
Single Top Support Rail
Inside Leg Insert Rail, ORStraight Leg Insert Rail
Position Support Rail Clampwhere indicated
&-TIGHTEN SECURELY-
Flat HeadCap Screw
Support Rail Clamp
Position Double Top Support Rail and Single TopSupport Rail so counter-sunk holes in Inside LegInsert Rail are aligned with holes on end of SupportRails.
Insert Flat Head Cap Screws and tighten with5MM allen wrench.
TABLE BASE FRAME ASSEMBLY(This step is not used on all tables)
Loosen bolts in Support Rail Clamp with 5MM Allenwrench, and postion on Support Rails where indicatedon the Assembly Master Illustration.
Clamp onto Rails and - SECURELY TIGHTEN - bolts.
Install required rail on opposite end of rails.
NOTE: Frame is assembled upside-down. Frameis to be flipped over after legs are installed.
CONFERENCE TOPSAssembly Instructions
Table Base Frame AssemblyTHIS STEP IS NOT USED ON ALL TABLES
NOTE: Frame is assembled upside-down .Frame is to be flipped over after legs are installed .
Instructions
• Position Double Top Support Rail and Single Top Support Rail so counter-sunk holes in Inside Leg Insert Rail are aligned with holes on end of Support Rails .
• Insert Flat Head Cap Screws and tighten with 5MM allen wrench .
• Loosen bolts in Support Rail Clamp with 5MM allen wrench, and position on Support Rails where indicated on the Assembly Master Illustration .
• Clamp onto Rails and -SECURELY TIGHTEN- bolts .
• Install required rail on opposite end of rails .
ELEVEN COLLABORATIVE
5
CONFERENCE TOPSAssembly Instructions
Leg AttachmentNOTE: Frame is assembled upside-down .Frame is to be flipped over after legs are installed .
USE THIS METHOD FOR:Rectangular Tables 84” and Smaller | Trapezoid Tables Square Tables | Round Tables | Three-legged Tables
Instructions
• Use 5MM allen wrench to loosen leg bolts . DO NOT REMOVE BOLTS
• Slide leg between rails until leg bottoms out, leaving no gap .
• Tighten bolts .
USE THIS METHOD FOR:Rectangular Tables larger than 84”
Instructions
• Use 5MM allen wrench to loosen leg bolts . DO NOT REMOVE BOLTS
• Slide leg between rails until leg bottoms out, leaving no gap .
• Tighten bolts .
On larger tables with 6 legs, center legs are inserted into Straight Leg Rails .
Outside Leg Rails
Loosen boltsfirst!
Outside LegRail
Inside LegRail
Loosen boltsfirst!
LEG ATTACHMENT
Use this method for:Rectanguar tables 84" and smaller.Trapezoid tables. Square tables.Round tables. Three-legged tables.
Use this method for:Rectanguar tables larger than 84".
Use 5MM allen wrench to loosenleg bolts. DO NOT remove bolts.
Slide leg between rails until legbottoms out, leaving no gap.
Tighten bolts.
Use 5MM allen wrench to loosenleg bolts. DO NOT remove bolts.
Slide leg between rails until legbottoms out, leaving no gap.
Tighten bolts.
On larger tables with six legs, centerlegs are inserted into Straight LegRails.
NOTE: Frame is assembled upside-down. Frameis to be flipped over after legs are installed.
Outside Leg Rails
Loosen boltsfirst!
Outside LegRail
Inside LegRail
Loosen boltsfirst!
LEG ATTACHMENT
Use this method for:Rectanguar tables 84" and smaller.Trapezoid tables. Square tables.Round tables. Three-legged tables.
Use this method for:Rectanguar tables larger than 84".
Use 5MM allen wrench to loosenleg bolts. DO NOT remove bolts.
Slide leg between rails until legbottoms out, leaving no gap.
Tighten bolts.
Use 5MM allen wrench to loosenleg bolts. DO NOT remove bolts.
Slide leg between rails until legbottoms out, leaving no gap.
Tighten bolts.
On larger tables with six legs, centerlegs are inserted into Straight LegRails.
NOTE: Frame is assembled upside-down. Frameis to be flipped over after legs are installed.
ELEVEN COLLABORATIVE
6
TOP JOINING PLATE ASSEMBLY(This step is not used on all tables)
NOTE: All Top Joining Plates are pre-assembled with clamps bolted in place.
120 x 42 & 120 x 48 Rectangular Tables,66 & 72 Square Tables and Trapezoid Tables
96 x 48, 108 x 48 & 120 x 48 Boat-Shaped Tables
All Other Tables with 2 Piece Tops
Clip Top Joining Plates to inside faces of Double and Single Support Rails.
Position Plates so they are at the mid-pointof the rails.
Tighten Clamps with 5MM allen wrench.
Clip Top Joining Plates to inside faces of Double and Single Support Rails.
Position Plate so it is at the mid-point ofthe rails.
Tighten Clamps with 5MM allen wrench.
Clip Top Joining Plates to inside faces ofStraight Leg Insert Rails (between the rails).
Slide Plates outward as far as they will go.
Tighten Clamps with 5MM allen wrench.
NOTE: Flip assembled frame over to rest on feet at this time..
CONFERENCE TOPSAssembly Instructions
Top Joining Plate AssemblyTHIS STEP IS NOT USED ON ALL TABLES
NOTE: Flip assembled frame over to rest on feet at this time .
NOTE: All Top Joining Plates are pre-assembled withclamps bolted in place .
Instructions
120x42 & 120x48 RECTANGULAR TABLES66 & 72 SQUARE TABLES AND TRAPEZOID TABLES
• Clip Top Joining Plates to inside faces of Double and Single Support Rails .
• Position Plates so they are at the mid-point of the rails .
• Tighten Clamps with 5MM allen wrench .
96x48, 108x48 & 120x48 BOAT-SHAPED TABLES
• Clip Top Joining Plates to inside faces of Double and Single Support Rails .
• Position Plates so it is at the mid-point of the rails .
• Tighten Clamps with 5MM allen wrench .
ALL OTHER TABLES WITH 2 PIECE TOPS
• Clip Top Joining Plates to inside faces of Straight Leg Insert Rails (between the rails) .
• Slide Plates outward as far as they will go .
• Tighten Clamps with 5MM allen wrench .
ELEVEN COLLABORATIVE
7
TOP
Top Clamp
Top Spacer
TOP CLAMP AND TOP SPACER INSTALLATION
Snap Top Clamps onto rails where shownon Assembly Master Illustration.
Flat surface of Top Clamp faces up.
When correctly postioned, tighten TopClamps (without over-tightening) using5MM allen wrench.
Peel off adhesive backers on TopSpacers and adhere one on each leg.
CONFERENCE TOPSAssembly Instructions
Top Clamp/Top Spacer Installation
Instructions
• Snap Top Clamps onto rails where shown on Assembly Master Illustration .
• Flat surface of Top Clamp faces up .
• When correctly positioned, tighten Top Clamps (without over-tightening) using 5MM allen wrench .
• Peel off adhesive backers on Top Spacers and adhere one on each leg .
ELEVEN COLLABORATIVE
8
Top Placement and Connection
Instructions
• Place top on frame .
• Two piece tops need to be placed so there is access to routes for Joint Fasteners on bottom side of top .
• Connect two halves of top together using Joint Fasteners in routed-out sections on connecting edges .
• Tighten with 7/16” wrench .
CONFERENCE TOPSAssembly InstructionsELEVEN COLLABORATIVE
9
DISTANCE A
DISTANCE A
DISTANCE BDISTANCE B
TOP ATTACHMENT
Position top so it is centered on the base.
Use two #8 X 1" truss head screws per Top Clamp to secure top to base.
If needed, use the same screws to fasten Top Joining Plate to top.
DISTANCE A
DISTANCE A
DISTANCE BDISTANCE B
TOP ATTACHMENT
Position top so it is centered on the base.
Use two #8 X 1" truss head screws per Top Clamp to secure top to base.
If needed, use the same screws to fasten Top Joining Plate to top.
CONFERENCE TOPSAssembly Instructions
Top Attachment
Instructions
• Position top so it is centered on the base .
• Use two #8 x 1” truss head screws per Top Clamp to secure top to base .
• If needed, use the same screws to fasten Top Joining Plate to top .
11.16
ELEVEN COLLABORATIVE