1
TABLE OF CONTENTS
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Dimensional Doors
EpicVue Clad Out-Swing Patio Doors may be specified as
"dimensional", by adjusting the desired rough opening width or height in
1/16" increments from standard.
EpicVue Clad Out-Swing Patio Doors are available in single, twin, triple
and quad panel doors. Transoms are available to match the variety of
door sizes. The standard size range includes sizes specifically
designed for replacement of older patio door models in existing
structures, as well as a full range of "true size" products for
architectural consistency.
Multiple Assemblies
EpicVue Clad Out-Swing Patio Doors are available in a wide variety of multiple panel configurations from the
factory, all of which are assembled with continuous sills. Clad out swing patio doors may be mulled below, or
beside other clad door and clad window products. Factory assembled mulls are limited in height (100"), width
(150").
Operation
EpicVue Clad Out-Swing Patio Doors are
available in a full range of operating styles.
Single panel doors may be specified as
stationary (non-venting) or can operate left or
right. Center swing two-or three-panel doors
are available with left or right operation. French
doors feature two operating panels (one active,
which opens first; and one inactive, which
closes first), and are available in two-panel and
four panel styles. Configuration and handing is
based on viewing the door from the exterior.
GENERAL INFORMATION
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
2
Radius
Vertical
Uneven Diamond
Rectangular Horizontal
Gothic
Prairie
EpicVue Clad Out-Swing Patio Doors are available with grilles in 5/8", 7/8", 1-1/8", 1-3/8", and 2-5/16" widths,
with grilles between the glass (GBG), or with Simulated Divided Lites. Standard lite cuts are rectangular, and
conform to the layouts noted in the charts on the next page. To use the chart, refer to the appropriate table by
the type of patio door and type of bars or grilles the section drawings illustrate. Then simply cross reference
the frame height and width to determine the standard lite cut.
Lite Cut Options
Special lite cut patterns can include a wide
variety of straight line and radius patterns.
The illustrations shown here represent just a
few of the possibilities. Rectangular,
horizontal, vertical, and Prairie lite patterns
are available in all standard size clad
swinging patio doors. Uneven, diamond,
radius, and Gothic lite cuts are available,
subject to approval. Approvals are based on
the ability to fulfill the design requirement
while maintaining the construction integrity of
the finished product.
Bar Alignment
Alignment of divided lite muntin bars from
one product to the next is often required by
fine architectural design. Wood grilles,
GBG's, and Simulated Divided Lites may be
specified with muntin bars aligned.
LITE CUT INFORMATION
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
3
5/8"
Note: The SDL Bar styles may be specified in mixed styles on the interior and exterior.
Interior
Exterior
7/8" 1-1/8" 1-3/8" 2-5/16"
Putty
Putty
Contemp.
Contemp.
Putty
Bead
SDL OPTIONS
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
4
Clear O
pening H
eight
29-7/82-6 True
41-7/83-6 True
35-7/83-0 True
31-7/82-8 True
23-7/82-0 True
33-7/83-0 Retro
29-7/82-8 Retro
27-7/82-6 Retro
21-7/82-0 Retro
Panel WidthPanel Callout
Clear Opening @ 90°
Clear Opening @ Maximum
Clear Opening @ Maximum
Clear Opening @ 90°
Clear Opening @ Maximum
Clear Opening @ 90°
Clear Opening @ Maximum
Clear Opening @ 90°
Fixed Panel Fixed Panel
Horizontal 1-Panel
@ 90° = Frame - 4 25/32"
@ Maximum = Frame - 2 7/8"
Horizontal 2 Panel Unit Hinged From Fixed Mullion
@ 90° = Frame - 1 7/16" - (Fixed panel size + 4 21/32")
@ Maximum = Frame - 1 7/16" - (Fixed panel size + 2 3/4")
Horizontal French Doors Hinged Off Jamb
@ 90° = Frame - 6 11/16"
@ Maximum = Frame - 2 7/8"
Horizontal French Doors Hinged Off Fixed Mullion
@ 90° = Frame Width - 2 x (Fixed panel size + 4 9/16")
@ Max = Frame Width - 2 x (Fixed panel size + 2 3/4")
Vertical Clear Opening
Standard Sill = Frame Height - 3 1/8"
Handicap Sill = Frame Height - 1 15/16"
Fixed Panel
CLEAR OPENING LAYOUT
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
5
General Notes:
Unit size is always the maximum size of the
window with or without trim and does not
include nail fin.
Masonry Opening:
Masonry opening is always 1/2" over (height
and width) the unit size or the outside of the trim
of the window.
Rough Opening:
Rough opening is always 3/4" over frame size
of the window.
A
B
C
F
DE
UNIT SIZING
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
6
10 1/8"
1 7/8"
1 1/4"
Side Jamb
Head Jamb
Transom Sill
1 7/8"
8 1/4"
1 1/4"
MULLION OPTIONS
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
7
Nailing Fin Options
4 9/16"
1 3/16"
4 11/16"
1 1/16"
1 3/16"
4 9/16"
Note: 11/16" Folding Nailing Flange will be used on Side Jambs and
Transom Sills with all Standard Trim options.
On units with 11/16" Folding Nailing Flange and No Exterior Trim, the 11/16"
Dripcap is used.
Exterior Trim Options
2 29/32"
2 1/2"
1 1/2"
1 9/32"
2"
1 9/32"
11/16" Folding
Nailing Fin
9/16" Folding
Nailing Fin
Rigid Nailing Fin
Kenison
Casing
2" Flat
Casing
3 1/2" Flat
Casing
TRIM OPTIONS
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: 3" = 1' - 0"
8
4" Bottom Rail
Standard Sill (4 9/16" Jamb)
Optional 11" Bottom Rail Handicap Sill
(6 9/16 Jamb)
4 5/8"
11"
10"
1/2"
4"
1 13/16" Typcial
1 1/16"
5 15/16"
1 1/16"
7/16"
6 5/8" Bottom Rail
Standard Sill (4 9/16" Jamb)
6 5/8"
1 1/16"
5 15/16"
1 1/16"
RAIL AND SILL OPTIONS
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
9
Transom Sill Nose (4 9/16 Jamb)
Transom Sill Nose (6 9/16" Jamb)
Note: Sill Nose can be used with all standard trim options.
Optional 4" Bottom Rail
Transom Extended Sill Nose (4 9/16" Jamb)
4 9/16"
Standard 2 1/4"
Bottom Rail
7/16"
1 7/16"
1 1/16"
2"
6 9/16"
7/16"
8 3/16"
2 1/16"
3 5/8" 4 9/16"
2 7/16"
1 5/8"
1 5/8"
TRANSOM RAIL AND SILL OPTIONS
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: 3" = 1' - 0"
10
Vertical Section
3 7/16"
1"
28 1/8" Standard
Raised Panel
Height
1"
3 9/16"
1 3/4"
1 3/16"
36" Standard
Lock Rail Height
4"
3 7/16"
Optional
Intermediate
Stile (Raised
Panels)
3 9/16"
12 1/16" Raised
Panel Width
1"1"
Standard 4" Stile
Horizontal Section
Optional
Intermediate
Lock Rail
RAISED PANEL - 1/2 LITE CONFIGURATION
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: 3" = 1' - 0"
11
1 3/4"
3 9/16"
1"
1 3/16"
15 1/16"
Raised Panel
Height
1"
Standard 4"
Bottom Rail
22 15/16" Lock
Rail Height
3 7/16"
4"
Vertical Section
3 7/16"
35 7/8"
Panel Width
27 11/16" Raised
Panel Width
3 7/16"
1" 1"
Horizontal SectionStandard 4" Stile
Optional
Intermediate
Lock Rail
RAISED PANEL - 3/4 LITE CONFIGURATION
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: 3" = 1' - 0"
12
4 9/16"1 3/16"
Fram
e S
ize
Ro
ugh
O
pe
nin
g
1/2"
1 7/16"
1 1/16"
Da
ylig
ht O
pen
in
g
4"
6 5/8"
Pa
nel S
ize
1 1/8"
1 1/16"
5 7/8"
5 3/4"
OPERATOR - VERTICAL SECTION WITH 4" BOTTOM RAIL
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
13
1 7/16"
Fra
me
S
ize
Ro
ug
h O
pe
nin
g
1/2"
4"
6 5/8"
Da
ylig
ht O
pen
in
g
Pan
el S
ize
1 1/16"1 1/16"
5 15/16"
4 9/16"1 3/16"
1 1/8"
5 3/4"
OPERATOR - VERTICAL SECTION WITH 6 5/8" BOTTOM RAIL
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
14
6 9/16"
1 7/16"
Fra
me
S
ize
Ro
ug
h O
pen
in
g
1/2"
1 3/16"
4"
11"
Da
yligh
t
Ope
ning
Pa
ne
l S
ize
1 1/16"
15/16"
7 3/4"
10"
OPERATOR - VERTICAL SECTION WITH 11" BOTTOM RAIL
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
15
4 9/16"
1 3/16"
4 9/16"
1 3/16"
Daylight Opening
Frame Size3/8" 3/8"
Rough Opening
4" 4"
1 1/16" 1 1/16"Panel Size
5 3/4" 5 3/4"
OPERATOR - HORIZONTAL SECTION WITH 4 9/16" JAMB DEPTH
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
16
6 9/16" 6 9/16"
1 3/16"1 3/16"
Daylight Opening
Frame Size
Rough Opening
3/8"
3/8"
4" 4"
1 1/16"1 1/16" Panel Size
7 3/4" 7 3/4"
OPERATOR - HORIZONTAL SECTION WITH 6 9/16" JAMB DEPTH
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
17
4 9/16"
Stationary Panel Size
Daylight
Opening
4"4"
1 1/16"
1 3/16"
Operating Panel Size
Panel Size
5 3/4"
3/8"
1 5/16"
Frame Size
Rough Opening
2-3 WIDE OPERATOR - HORIZONTAL SECTION WITH 4 9/16" JAMB DEPTH
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
18
6 9/16"
Stationary Panel Size
Daylight
Opening
4"3 15/16"
1 1/16"
Operating Panel Size
Panel Size
1 3/16"
7 3/4"
3/8"
1 5/16"
Frame Size
Rough Opening
2-3 WIDE OPERATOR - HORIZONTAL SECTION WITH 6 9/16" JAMB DEPTH
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
19
Daylight
Opening
4" 4"4" 4"
Panel Size 1 5/16"1 5/16"
3 WIDE OPERATOR - HORIZONTAL SECTION
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
20
4 9/16"1 3/16"
1 7/16"
4"
4"
Da
yligh
t O
pe
nin
g
Fra
me
S
ize
Ro
ugh
O
pe
ning
1/2"
1 1/8"
1"
Pan
el S
ize
5 3/4"
8 1/2"
SIDELITE - VERTICAL SECTION WITH 4" BOTTOM RAIL
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
21
4 9/16"
1 3/16"
4 9/16"
1 3/16"
Daylight Opening
Frame Size
Rough Opening
3/8" 3/8"
4"
1 1/16"
4"
1 1/16" Panel Size
5 3/4" 5 3/4"
SIDELITE - HORIZONTAL SECTION WITH 4 9/16" JAMB DEPTH
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
22
6 9/16"
1 3/16"
6 9/16"
1 3/16"
Daylight Opening
Frame Size
Rough Opening
3/8"
4" 4"
1 1/16"1 1/16" Panel Size
7 3/4" 7 3/4"
3/8"
SIDELITE - HORIZONTAL SECTION WITH 6 9/16" JAMB DEPTH
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
23
4 9/16"
1 7/16"
1 7/16"
Fra
me
S
ize
Rou
gh O
pen
in
g
1/2"
1 3/16"
2 1/4"
Da
yligh
t O
pe
nin
g
2 1/4"
15/16"
5 3/4"
4 9/16"
Pa
ne
l S
ize
5 3/4"
1 3/16"
TRANSOM - VERTICAL SECTION WITH 2 1/4" BOTTOM RAIL
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
24
6 9/16"1 3/16"
1 1/16"
1 1/16"
Fra
me
S
ize
Rou
gh O
pen
in
g
3/8"
Da
yligh
t O
pe
nin
g
Pa
ne
l S
ize
1 1/16"
15/16"
4"
4"
7 3/4"
1 3/16"
7 3/4"
6 9/16"
3/8"
TRANSOM - VERTICAL SECTION WITH 4" BOTTOM RAIL
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
25
4 9/16"
1 3/16"
3/8"
1 1/16"
4"
Daylight
Opening
4"
Operating Panel Size
Panel Size
5 3/4"
1 5/16"
Frame Size
Rough Opening
FRENCH - HORIZONTAL SECTION WITH 4 9/16" JAMB DEPTH
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
26
6 9/16"
1 3/16"
1 1/16"
4"
Daylight
Opening
4"
Operating Panel Size
Panel Size
7 3/4"
3/8"
1 5/16"
Frame Size
Rough Opening
FRENCH - HORIZONTAL SECTION WITH 6 9/16" JAMB DEPTH
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
27
4 9/16"
Daylight
Opening
4"
1 1/16"
4" 4"
1 3/16"
Panel Size
5 3/4"
3/8"
1 5/16"
Frame Size
Rough Opening
QUAD FRENCH - HORIZONTAL SECTION WITH 4 9/16" JAMB DEPTH
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
28
6 9/16"
1 3/16"
Daylight Opening
2 1/4"
1 1/16"
2 1/4" 4"
Panel Size
7 3/4"
3/8"
1 5/16"
Frame Size
Rough Opening
QUAD FRENCH - HORIZONTAL SECTION WITH 6 9/16" JAMB DEPTH
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
29
EPICVUE
Daylight
Opening
4"4"4"
Panel Size
4"
1 5/16"1 5/16"
QUAD FRENCH ASTRAGAL - HORIZONTAL SECTION
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
30
Daylight
Opening
4" 4"2 1/4" 4"
Panel Size1 5/16" 1 5/16"
QUAD FRENCH COMBO SIDELITE ASTRAGAL - HORIZONTAL SECTION
Architectural Design Manual
November 2017
Product specifications may change without notice.
Questions? Consult JELD-WEN customer service.
EPICVUE™
CLAD-WOOD PATIO DOOR
OUTSWING PATIO DOOR
Scale: NTS
31