INSTRUCTION MANUAL
iPX5155Ethernet BGM / Paging Client (Audio Extractor)
Thank you for choosing another quality product from Amperes Electronics.
iPX5155 is a combination of Paging and Music clients in a box, reducing the equipment counts for audio transmission in a LAN environment. It is suitable for distributed paging configuration, such a placement of amplifiers in risers in multiple blocks or systems.
How it works ... iPX5155 receives normal BGM broadcast from central system, such as from iPX5200 ( audio music server ) or PMX software and deliver balanced audio output to amplifiers. Upon Paging broadcast and intended for the particular address of iPX5155, the BGM shall be muted and resume when Paging ends. UART ( RS485 ) is available for controls of zone selection if required.
With iPX5000 series of LAN paging equipment, new setup for large and decentralized paging system is now made easier and affordable. Upgrading to IP from conventional analogue PA system would be made achievable without having to change the whole system.
Parts Identification
2
PAGE 2 iPX5155 | ETHERNET BGM / PAGING CLIENT
3 6 71
1. INDICATOR LEDS LEDs for Power, Server, Status and Streaming.
2. POWER PORT 24V DC power supply input.
3. ETHERNET PORT Ethernet Port for connection to network switch.
4. RESET BUTTON Button for resetting the unit to factory default. Use only when required as setting done previously would be lost.
5. RELAY CONTACT This ports provide a dry contact which can be used to connect E/M overriding signal or activate ALL CALL at speaker zone selector.
6. EXTERNAL MESSAGE TRIGGER PORT Ethernet message player can be linked to it and can be broadcasted to the speakers when this port is triggered. A voltage free contact is recommended to trigger the message playback.
7. RS485 PORT For data Transmission (RS485) from PD paging mic or output data for TD6240 / 6080 controls.
8. SIGNAL INDICATOR LED to indicate audio signal’s presence.
9. MIC AUDIO INPUT Audio input signal from paging mic with balanced line level.
10. AUDIO OUTPUT PORT Audio output from client for connection to mixer, etc with balanced line level.
Front View Rear View
9 1054
8
iPX5155 | ETHERNET BGM / PAGING CLIENT PAGE 3
Connecting to iPX5155
PD SERIES PAGING MIC
iPX5155 / iPX5151
cat5e
iPX
510
1am
pere
s
AC
TST
ATU
SPO
WER
REM
FROM FIRE ALARM INTERFACE
EP12
00A
EMER
. PA
GING
MIC
MR13
01 M
ESS.
PL
AYER
MP3 /
TUN
ER / C
D
MEDI
A PL
AYER
iPX5
101
IP P
AGIN
G CO
NTRO
LLER
iPX5200 MUSIC SERVER
iPX5155 / iPX5151
NETWORK SWITCH WITH FIBER LINK
iPX5
155
Music / Paging Audio + Data
LOCAL PA EQUIPMENT INCL. PRE-AMPLIFIER MIXER ZONE
DECODER POWER AMPLIFIERS ETC.
Fiber
redu
ndan
t loop
( no
t ava
ilable
to al
l swi
tcher
s )
iPX 5300ETHERNET MUSIC CLIENT
ETHERNET ADDRESS
ETHERNET
RESET
BALANCED LINE
OUTPUT
amperes
LOCAL PA EQUIPMENT INCL. PRE-AMPLIFIER MIXER ZONE
DECODER POWER AMPLIFIERS ETC.
NETWORK SWITCH WITH FIBER LINK
iPX5
155
SUB RACK
MAIN RACK
Note: In a system, only one iPX5101 is required, no matter what the size of the system or the number of clients ( iPX5155 ) are installed.
Music / Paging Audio + Data
Device Setup Via Browser
PAGE 4 iPX5155 | ETHERNET BGM / PAGING CLIENT
iPX5155 shall require some simple setups, kindly follow the step by step instructions as listed below. The unit shall be connected to LAN network together with iPX5101 IP Server / PMX II to form a complete system. The default IP address is 192.168.0.151. Login page shall appear and the default User ID and Password are both “admin”.
Info / Main Page
Info: Providing hardware, network and Application information. This shall be the first page once you entered the system’s http browser.
Network Configuration: For configuration of IP address and its related ports.
System configuration: For Application Settings.
Music Source configuration: For Music stream source Settings.
Network Configuration
Unless required, you are recommended to change the IP address only, leaving other setting such as port number as default. Once the address has been changed to suit the environment, click the “Save Changes” button.
Hardware Information
Network Information
Firmware Version
Hardware Revision
Serial Number
Device Name
Application Information
MAC Address
IPv4 Address
Subnet Mask
Gateway Address
Server Name
Server IP
Communication Port
Info
Network Configuration
System Configuration
Restart Client
MAIN
Music Source
IP Address
Network Settings
Application Settings
Subnet Mask
Gateway Address
Communication Port
iPX5155 | ETHERNET BGM / PAGING CLIENT PAGE 5
Device Setup Via Browser
System Configuration
Application Setting: The volume, bass and treble for selected groups can be set accordingly. The default source refers to the unit’s selected source every time it is turned on.
Device Name: You can rename the device name.Paging Server IP: To indicate the address of the iPX5101 of which the client is connected to.Priority: Set the priority level of the client, with 1 being the highest priority.Zone Range: To indicate number of zones available in the overall system in relation to the server.Restricted zone: Indicates the zone which are restricted for paging.Volume: Volume setting.Bass, Treble: Setting the level to suit the environment. Web Page Theme: You can choose the theme of the web page.
Authentication: You can alter the user name and password to avoid unnecessary access to the system.System Updates: Both the browser and firmware are stored in the unit’s memory. Should there be any updates available, use this section to perform system upgrades accordingly.
Note:Ensure Paging Server IP is correctly set. If the paging source is iPX5101, the default IP address shall be 192.168.0.151. If PMX II LAN is used as the source, the Paging Server IP shall correspond to the PC’s IP address.
Music Source Configuration
Only iPX5200 or PMX Music stream source is currently supported, more will be added in near future (web radio, CE cast etc).
In the “Music Source Configuration” tab you can choose the enable / disable the stream. Disabling BGM will make it act just like iPX5151.
- Stream address is the multicast IP Address of the iPX5200.
- Stream port is the stream port of the server. Default: 3003
Music Source Configuration
iPX5200 - Ethernet Music Server
Enabled
Stream Address
Stream Port
Application Settings
Device Name
Paging Server IP
Priority
Zone Range
Restricted Zones
VOLUME
BASS
TREBLE
Web Page Theme
Authentication
New User Name
Old Password
New Password
Confirm Password
System Updates
Update Web Page
Update Firmware
No the chosen
No the chosen
PAGE 6 iPX5155 | ETHERNET BGM / PAGING CLIENT
System Bootloading (Firmware / Browser Update)
1. To update the firmware, choose binary file with “appbin” extension ( new file downloaded from website or source directly from us ) and click update.
2. To update the browser, choose binary file with “webbin” extension and click update.
To update the firmware & browser via html page, enter the IP Address (192.168.0.151) and go to ‘System Configuration’ page under “ system updates ” for firmware or browser update.
Update via Browser
1. Default reset: Press & hold the reset button until LED “streaming” ON.
2. At the web browser, enter the IP address 192.168.0.151 and the page below shall appear. This is a “Safe Mode” page for Browser or Firmware update.
Safe mode: Press & hold the reset button until LED “status” ON.
System firmware or Browser shall be updated once in a while when new features are available or to fix bugs. There are 2 methods of doing;
Server Reset Bootloading
If the client “hanged”, it is required to perform system reset by :
Update Firmware :- To update firmware, choose binary file with “appbin” exten-sion ( new file downloaded from website or source directly from us ) and click update.
Update Web page :- To update web page, choose binary file with “webbin” exten-sion and click update.
System Updates
Update Web Page
Update Firmware
No the chosen
No the chosen
iPX5155 | ETHERNET BGM / PAGING CLIENT PAGE 7
Technical Specification
Power requirement :VoltageCurrent
Connectivity- LAN interface- Common protocols- Priority protocols
Audio- Analogue in/out (peak-to-peak)- Input impedance- Output impedance- Total harmonic distortion (THD)- S/N ratio (full scale signal)- Digital format (decode) - Digital format (encode)
User interface
Firmware upgrade
Operating condition :TemperatureHumidityCase :Dimension (WxHxD)Weight
24V DC<100 mA
RJ-45, 100Mb/sTCP/IP, UDP, IGMP, HTTPUDMP, ADP
(Web Browser) IE V8+, Firefox V22+, Google Crome V25+, RS485
Via Web Browser / Bootloading
-20°C ~ 80°C0 - 70%
100 x 147 x 40 mm300 g
1.25Vrms3k Ohm600 Ohm0.1%83 dBIMA ADPCM / MP3 (CBR / 320 kbps max) / WAV / MP2 / OGG / WMA / FLACIMA ADPCM
Note:The above specifications are correct at time of printing but subjected to changes without prior notice due to product improvements.
Warranty Conditions
Disclaimer
AMPERES ELECTRONICS SDN BHDMADE IN MALAYSIA
Published : March 2016ISO 9001: 2008
Design & Manufacture of Public Address Equipment and SystemsCerti�cate No. 16895 / A / 0001 / UK / En
Only Amperes Electronics Service Centres are allowed to make warranty repairs : a list of Amperes Electronics Service Centres may be asked for by the purchaser or send directly to Amperes Electronics Sdn Bhd at 70 Jalan Industri PBP 3, Tmn Perindustrian Pusat Bandar Puchong, 47100, Puchong, Selangor, Malaysia or its authorized master distributor, TNT Links Sdn Bhd / MyPA Systems Sdn Bhd. This warranty is not valid if repairs are performed by unauthorized personnel or service centres.
This warranty covers only repairs and replacement of defective parts ; cost and risks of transportation as well as removal and installation of the product from the main system are for the account of the purchaser. This warranty shall not extend to the replacement of the unit.
This warranty does not cover damages caused by misuse, neglect, accident of the product as well as using the product with power supply voltage other than shown on the product, or any other power supply source / adaptor not recommended by the manufacturer.
This warranty does not cover damages caused by fire, earthquakes, floods, lightning and every cause not directly related to the unit.
This warranty does not include any indemnity in favor of the purchaser or the dealer for the period out of use of the unit; moreover the warranty does not cover any damages which may be caused to people and things when using the product.
This warranty certificate is valid only for the described product, and is not valid if modifications are made on this certificate or on the identification label applied on the product.
This warranty covers all the material and manufacturing defects and is valid for a period of 12 months from the date of purchase or for a longer period in countries where this is stated by a national law. In this case, the extension is valid only in the country where the product is purchased.
Amperes Electronics Sdn Bhd is not obliged to modify previously manufactured products under warranty if the design changes or improvements are made.
Information contained in this manual is subject to change without prior notice and does not represent a commitment on the part of the vendor. AMPERES ELECTRONICS SDN BHD shall not be liable for any loss or damages whatsoever arising from the use of information or any error contained in this manual.
It is recommended that all services and repairs on this product be carried out by AMPERES ELECTRONICS SDN BHD or its authorized service agents.
AMPERES series must only be used for the purpose they were intended by the manufacturer and in conjunction with this operating manual.
AMPERES ELECTRONICS SDN BHD cannot accept any liability whatsoever for any loss or damages caused by service, maintenance or repair by unauthorized personnel, or by use other than that intended by the manufacturer.