EVB-USB5807/6 Evaluation Board User’s...

2016 Microchip Technology Inc. DS50002543A

EVB-USB5807/6Evaluation Board

User’s Guide

DS50002543A-page 2 2016 Microchip Technology Inc.

Information contained in this publication regarding device applications and the like is provided only for your convenience and may be super-seded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REP-RESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OROTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE,MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Micro-chip devices in life support and/or safety applications is entirely at the buyer’s risk, and the buyer agrees to defend, indemnify and holdharmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly orotherwise, under any Microchip intellectual property rights unless otherwise stated.

Trademarks

The Microchip name and logo, the Microchip logo, AnyRate, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KeeLoq, KeeLoq logo, Kleer, LANCheck, LINK MD, MediaLB, MOST, MOST logo, MPLAB, OptoLyzer, PIC, PICSTART, PIC32 logo, RightTouch, SpyNIC, SST, SST Logo, SuperFlash and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.

ClockWorks, The Embedded Control Solutions Company, ETHERSYNCH, Hyper Speed Control, HyperLight Load, IntelliMOS, mTouch, Precision Edge, and QUIET-WIRE are registered trademarks of Microchip Technology Incorporated in the U.S.A.

Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PureSilicon, RightTouch logo, REAL ICE, Ripple Blocker, Serial Quad I/O, SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.

SQTP is a service mark of Microchip Technology Incorporated in the U.S.A.

Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries.

GestIC is a registered trademarks of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries.

All other trademarks mentioned herein are property of their respective companies.

© 2016, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved.

ISBN: 9781522409984

Note the following details of the code protection feature on Microchip devices:

• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrity of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of ourproducts. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such actsallow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified.

QUALITYMANAGEMENTSYSTEMCERTIFIEDBYDNV

== ISO/TS16949==

EVB-USB5807/6 Evaluation Board User’s Guide


Object of Declaration: EVB-USB5807/6

EVB-USB5807/6EVALUATION BOARD

USER’S GUIDE

Table of Contents

Preface ........................................................................................................................... 5Introduction............................................................................................................ 5

Document Layout .................................................................................................. 5

Documentation Conventions ................................................................................. 6

Warranty Registration............................................................................................ 7

The Microchip Web Site ........................................................................................ 7

Customer Support ................................................................................................. 7

Document Revision History ................................................................................... 7

Chapter 1. Overview1.1 EVB-USB5807/6 Evaluation Kit Overview ...................................................... 81.2 Features ......................................................................................................... 81.3 Block Diagram ................................................................................................ 91.4 References ..................................................................................................... 91.5 Definitions ..................................................................................................... 10

Chapter 2. Getting Started2.1 Kit Contents .................................................................................................. 112.2 Getting Started ............................................................................................. 11

2.2.1 Quick Start ................................................................................................. 112.2.2 Differences between EVB-USB5807 and EVB-USB5806 ......................... 12

Chapter 3. Hardware Configuration3.1 Hardware Configuration Options .................................................................. 13

3.1.1 Configuration ............................................................................................. 143.1.2 Power Source - Self Powered ................................................................... 153.1.3 Downstream Port Control .......................................................................... 153.1.4 EVB-USB5807/6 LED Indicators ............................................................... 163.1.5 EVB-USB5807/6 Switches ........................................................................ 183.1.6 EVB-USB5807/6 Connector Descriptions ................................................. 183.1.7 Test Points on EVB-USB5807/6 ................................................................ 19

Appendix A. EVB-USB5807/6 SchematicsA.1 Introduction .................................................................................................. 21

Appendix B. EVB-USB5807/6 BOMB.1 Introduction .................................................................................................. 26

Appendix C. USB5807/06 PCB Silk ScreensC.1 Introduction .................................................................................................. 31

Worldwide Sales and Service .................................................................................... 33

2016 Microchip Technology Inc. DS50002543A-page 4


USER’S GUIDE

Preface

INTRODUCTION

This chapter contains general information that will be useful to know before using the EVB-USB5807/6 Evaluation Board User’s Guide. Items discussed in this chapter include:

• Document Layout

• Documentation Conventions

• Warranty Registration

• The Microchip Web Site

• Customer Support

• Document Revision History

DOCUMENT LAYOUT

This document describes how to use the EVB-USB5807/6 as a demonstration platform optimized for portable applications. The manual layout is as follows:

• Chapter 1. “Overview”

• Chapter 2. “Getting Started” – Provides information about set-up and operation of the EVB-USB5807/6 Evaluation Board.

• Chapter 3. “Hardware Configuration” – Includes information about the hardware configuration of the EVB-USB5807/6 Evaluation Board.

• Appendix A. “EVB-USB5807/6 Schematics”

• Appendix B. “EVB-USB5807/6 BOM”

• Appendix C. “USB5807/06 PCB Silk Screens”

NOTICE TO CUSTOMERS

All documentation becomes dated, and this manual is no exception. Microchip tools and documentation are constantly evolving to meet customer needs, so some actual dialogs and/or tool descriptions may differ from those in this document. Please refer to our web site (www.microchip.com) to obtain the latest documentation available.

Documents are identified with a “DS” number. This number is located on the bottom of each page, in front of the page number. The numbering convention for the DS number is “DSXXXXXA”, where “XXXXX” is the document number and “A” is the revision level of the document.

For the most up-to-date information on development tools, see the MPLAB® IDE online help. Select the Help menu, and then Topics to open a list of available online help files.



DOCUMENTATION CONVENTIONS

This manual uses the following documentation conventions:

DOCUMENTATION CONVENTIONS

Description Represents Examples

Arial font:

Italic characters Referenced books MPLAB® IDE User’s Guide

Emphasized text ...is the only compiler...

Initial caps A window the Output window

A dialog the Settings dialog

A menu selection select Enable Programmer

Quotes A field name in a window or dialog

“Save project before build”

Underlined, italic text with right angle bracket

A menu path File>Save

Bold characters A dialog button Click OK

A tab Click the Power tab

N‘Rnnnn A number in verilog format, where N is the total number of digits, R is the radix and n is a digit.

4‘b0010, 2‘hF1

Text in angle brackets < > A key on the keyboard Press <Enter>, <F1>

Courier New font:

Plain Courier New Sample source code #define START

Filenames autoexec.bat

File paths c:\mcc18\h

Keywords _asm, _endasm, static

Command-line options -Opa+, -Opa-

Bit values 0, 1

Constants 0xFF, ‘A’

Italic Courier New A variable argument file.o, where file can be any valid filename

Square brackets [ ] Optional arguments mcc18 [options] file [options]

Curly brackets and pipe character: { | }

Choice of mutually exclusive arguments; an OR selection

errorlevel {0|1}

Ellipses... Replaces repeated text var_name [, var_name...]

Represents code supplied by user

void main (void){ ...}


Preface

WARRANTY REGISTRATION

Please complete the enclosed Warranty Registration Card and mail it promptly. Sending the Warranty Registration Card entitles users to receive new product updates. Interim software releases are available at the Microchip web site.

THE MICROCHIP WEB SITE

Microchip provides online support via our web site at www.microchip.com. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information:

• Product Support – Data sheets and errata, application notes and sample programs, design resources, user’s guides and hardware support documents, latest software releases and archived software

• General Technical Support – Frequently Asked Questions (FAQs), technical support requests, online discussion groups, Microchip consultant program member listing

• Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives

CUSTOMER SUPPORT

Users of Microchip products can receive assistance through several channels:

• Distributor or Representative

• Local Sales Office

• Field Application Engineer (FAE)

• Technical Support

Customers should contact their distributor, representative or field application engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document.

Technical support is available through the web site at: http://www.microchip.com/support

DOCUMENT REVISION HISTORY

Revision Section/Figure/Entry Correction

DS50002543A (10-07-16) Initial release of this document


www.microchip.com

http://www.microchip.com/support

http://www.microchip.com/support


USER’S GUIDE

Chapter 1. Overview

1.1 EVB-USB5807/6 EVALUATION KIT OVERVIEW

The EVB-USB5807/6 is a demonstration and evaluation platform that provides the nec-essary requirements and interface options for evaluating the USB5807 or USB5806 (depending on PCB population options), a 7/6-Port SS/HS USB Smart Hub on a 4-layer RoHS-compliant Printed Circuit Board (PCB). This will allow the user to gain an under-standing of the product and accelerate the integration of the USB5807/06 into the user’s design. The EVB-USB5807/6 is compliant with the USB 3.1 (Gen1) Specification and supports SuperSpeed (SS), High-Speed (HS), Full-Speed (FS), and Low-Speed (LS) USB signaling for complete coverage of all defined USB operation speeds. The evaluation platform supports seven/six downstream ports that are USB 2.0 and USB 3.1 Gen 1 compliant. The EVB-USB5807/6 platform also supports battery charging on all downstream ports (maximum of 13A* at any one time). The EVB-USB5807/6 is con-figured for operation through internal default settings and supports custom configura-tions through SMBus or through the external 16-Mbit SPI Flash device, U2. The EVB-USB5807/6 demonstrates driver compatibility with Microsoft® Windows® 8x, Windows 7, Windows XP, Mac OS® X 10.4+, and Linux® hub drivers.

See Section 1.2 “Features” for more information.

1.2 FEATURES

• Microchip’s FlexConnect, PortSwap, PHYBoost™, and VariSense™ technologies.

• USB5807/06 in a 100-pin QFN RoHS compliant package.

• USB 3.1 Gen 1 compliant (SS, HS, FS, and LS operation).

• USB pins are 5 V tolerant.

• Self powered operation.

• Seven downstream USB 2.0 / USB 3.1 Gen 1 ports for the USB5807 option, Six downstream USB 2.0 / USB 3.1 Gen 1 ports for the USB5806.

• All downstream ports support individual port power and overcurrent sense.

• All downstream ports can be enabled for battery charging with the battery charging select switch SW1. (BC1.2 or SE1, 2.1A max per port).

• Onboard SPI Flash for external downloadable firmware.

• Low-cost 4-layer space saving design.

• Operates from a single voltage (+12.0 V, regulated) external power supply.

• Onboard 25 MHz crystal or external clock input.

• Single onboard +5.2 V, 6 Amp regulator. MCP19035 based switching regulator design provides 5.2 V at up to 15 A when using a 12 V, 85 W supply.

• Single onboard +3.3 V, 0.5 Amp regulator.

• Single onboard +1.2 V, 2 Amp regulator.

• Port Power LED indicators.

Note: *Requires a 12V, 85W supply.


Overview

• SPI Flash activity blue LED indicator.

• Reset red LED indicator.

• Green LED indicators for 5V, 3.3V, 1.2V supplies.

• Dual color LED USB Suspend indicator (green=run/yellow=suspend).

• USB Type-C upstream green LED charging capability indicators: 3A, 1.5A, Legacy.

• SMBus current monitor on each USB Type-C downstream port.

• Terminal block connector for use with an external bench supply.

• Removable/non-removable downstream ports can be configured with switch SW2.

1.3 BLOCK DIAGRAM

1.4 REFERENCES

• USB5806 Data Sheet

• USB5807 Data Sheet

FIGURE 1-1: EVB-USB5807/6 BLOCK DIAGRAM

USB5807/6FlexConnect

P0

P1 P2 P3 P4 P5 P6 P7

PROG_FUNC3.3V 1.2VXTAL

MIC2039PPC

USB3‐AP1

MIC2039PPC

USB3‐AP2

MIC2039PPC

USB3‐AP3

MIC2039PPC

USB3‐AP4

MIC2039PPC

USB3‐AP5

MIC2039PPC

USB3‐AP6

MIC2039PPC

USB3‐AP7

EVB‐USB5807

USB3‐BP0

25MHz

Flex Shunt

Flex LED

Aardvark

Battery Charging Strap Select Switches

Non Removable Strap Select Switches

SST26VFSPI Flash

USB Speed/BC LEDs

Host Speed LEDs

EVB‐USB5806

DC Jack12V In

MCP1903512V to 5.0V

MCP18245.0V to 3.3V

MIC232015.0V to 1.2V

5.0V3.3V 1.2V



1.5 DEFINITIONS

• BC1.2 - Latest USB-IF specified USB battery charging standard

• CDP - Charging Downstream Port. A BC1.2 compliant port allows simultaneous USB data and USB charging.

• DCP - Dedicated Charging Port. A BC1.2 compliant port which is only capable of USB charging (no data).

• DFP - Downstream Facing Port

• EVB - Evaluation Board

• FlexConnect - Special feature which allows the USB Hub’s upstream port to exchange roles with downstream port 1 via SMBus control, GPIO control, or USB command.

• OTP - One Time Programmable Memory

• SDP - Standard Downstream Port. A standard USB port with no high-current bat-tery charging capabilities.

• SE1 - Type of Battery Charging (non-USB compliant) which sets the USB D+/D- to specific DC voltages to communicate charging capability

• UFP - Upstream Facing Port

• USB-IF - USB Integrators Forum. Collection of corporate sponsored members responsible for developing USB specifications.



USER’S GUIDE

Chapter 2. Getting Started

2.1 KIT CONTENTS

The EVB-USB5807/6 evaluation board includes the basic equipment necessary for evaluation. The items included are:

1. EVB-USB5807/6 Evaluation Board

2. 12V Power Supply

2.2 GETTING STARTED

The Microchip EVB-USB5807/6 is designed for flexible configuration solutions. It can be configured via default internal register settings, downloadable external firmware to an onboard SPI Flash, through SMBus, or through the onboard configuration switches.

Microchip provides a comprehensive software programming tool, ProTouch2, for con-figuring USB5807/06 functions, registers, and OTP memory. When configured with the default internal register settings, the device operates as a USB 3.1 Gen 1 / USB 2.0 hub with 7 (for USB5807 option) or 6 (for USB5806 option) USB ports and Microchip’s standard VID/PID/DID settings. For additional information on the Pro-Touch2 program-ming tool, refer to Software Libraries within Microchip USB5807/6 product page at www.microchip.com/USB5807 or www.microchip.com/USB5806

2.2.1 Quick Start

To quickly start using the board, perform the following steps:

1. Connect the included 12V power supply to the barrel connector on the EVB-USB5807/6(J10).

2. Using a standard USB cable, connect the EVB-USB5807/6 to a USB host via the USB Type-B Connector (J1).

3. You may now connect devices to any of the downstream ports to enumerate and use that device with the USB host.

4. You can perform additional configuration or evaluate specific features by launch-ing the ProTouch2 software on your USB host or by manipulating the included hardware configuration options detailed in the next chapter.


http://www.microchip.com/USB5807

http://www.microchip.com/USB5807


2.2.2 Differences between EVB-USB5807 and EVB-USB5806

Differences between the USB5807 and USB5806 are summarized in the table below.

TABLE 2-1: EVB-USB5807 AND EVB-USB5806 QUICK FEATURE SET COMPARISON

Feature USB5807 USB5806

Number of downstream ports 7 6

Battery Charging on all downstream ports Yes Yes

Internal Hub Feature Controller device No Yes

SMBus slave interface Yes Yes

USB to I2C Master/SPI Master/GPIO bridging function No Yes

FlexConnect via GPIO control Yes Yes

FlexConnect via USB command No Yes

OTP programming via SMBus Yes Yes

OTP programming via USB command No Yes

Downstream port connection speed indicators (LED) Yes Yes

Upstream port connection speed indicator (LED) Yes No



USER’S GUIDE

Chapter 3. Hardware Configuration

3.1 HARDWARE CONFIGURATION OPTIONS

FIGURE 3-1: EVB-USB5807 (TOP-SIDE)

FIGURE 3-2: EVB-USB5806 (TOP-SIDE)



3.1.1 Configuration

3.1.1.1 EXTERNAL SPI FLASH

Upon power-up, the USB5807/06 first looks for an external SPI ROM device and a valid signature in the Flash. If one is found, the external ROM is enabled and code execution is initiated from the external SPI ROM device.

To select the SPI device, install a shunt to short J5. When code is executing from a SPI ROM device, a blue LED (D2) will illuminate.

Note 1: CFG_BC and CFG_Non-Rem options are deselected when a shunt is installed on J5. When operating SPI mode, all configuration is handled by the code executing from the SPI ROM device.

2: If the SPI Flash is not properly programmed or has an invalid signature, the USB5807/06 will revert to internal defaults even if the SPI ROM is selected.

3.1.1.2 SMBUS

If a SPI Flash device is not found, the firmware checks if SMBus is enabled.

To select SMBus configuration, leave J5 open to disconnect the SPI ROM and select the CONFIG2 option from the CFG_STRAP header by shunting pins 1-2 of J6. The SMBus signals may be accessed at J8, pins 1 and 3.

Remember, if configured for SMBus operation, the USB5807/06 will wait indefinitely for data from the SMBus interface and will not enumerate to the USB host until the special USB Attach command is sent.

3.1.1.3 INTERNAL DEFAULT CONFIGURATIONS WITH STRAPPING OPTIONS

When the USB5807/06 does not detect a valid SPI Flash image or SMBus configura-tion upon power-up, the USB5807/06 uses internal default register settings. It also sets the Vendor ID, Product ID, Language ID, and Device ID, and additional settings from internal ROM code.

If configuration is not performed through SPI or SMBus, additional configuration is available through three functions: CFG_STRAP, CFG_BC_EN and CFG_NON-REM. The controls are configured by selecting on of six resistor values for each pin. These straps are read by the USB5807/06 device at power-on to determine the default con-figuration of the device.

To select the configuration mode, a shunt must be installed to short two pins of the J6 header.

To use the battery charging and non-removable port strapping options, leave J5 open. Select the desired CFG_BC_EN and CFG_NON-REM options by enabling only one position for each of the CFG_BC_EN Select and CFG_NON-REM Select switches (SW1 and SW2).

TABLE 3-1: CFG_SEL (J6) OPTIONS

Shunt Position Configuration

Pins 1-2 CFG2 - Speed Indicator Mode + SMBus Slave Mode

Pins 2-3 CFG1 - Speed Indicator Mode + I2C Bridging Mode [Default]

Pins 3-4 CFG5 - GPIO Mode + I2C Bridging Mode


Hardware Configuration

3.1.2 Power Source - Self Powered

The EVB-USB5807/6 only supports self-powered operation, and is powered through one +12.0 V regulated 'wall wart' external power supply. The power supply plugs into the 2.5 mm connector J9 on the board. Alternatively, an external voltage can be sup-plied to the screw terminal TERM_BLOCK_2P (J9) or test point TP3. The +12.0 V feeds a 15 A regulator which outputs +5.2 V across the board. This +5.2 V output sup-plies the +3.3 V and +1.2 V onboard regulators.

3.1.3 Downstream Port Control

USB power to the seven downstream ports is controlled via port power controllers with auto-discharge function. This provides up to 2.1 A of USB battery charging power to each port.

TABLE 3-2: BATTERY CHARGING OPTIONS (CFG_BC_EN - SW1)

Switch Position Configuration

1 No battery charging enabled

2 Port 1 is BC1.2 enabled

3 Ports 1-2 are BC1.2 enabled



6 All ports are BC1.2 enabled [Default]

TABLE 3-3: NON-REMOVABLE PORT OPTIONS (CFG_NON-REM - SW2)

Switch Position Configuration

1 All ports are removable [Default]

2 Port 1 is non-removable

3 Ports 1-2 are non-removable



6 All ports are non-removable

Note: The supplied 12.0 V external power supply cannot support simultaneousbattery charging on all downstream ports. Use a higher power supply if therequired test use case exceeds the power capability of the supply. Failureto heed to this warning could result in damage to the 12.0 V external powersupply.



3.1.4 EVB-USB5807/6 LED Indicators

Table 3-4 describes the LED indicators included on the EVB-USB5807/6.

TABLE 3-4: LED INDICATOR DESCRIPTIONS

REF.DES.

Label Description

D2 “SPI Flash Active”

Indicates that the SPI ROM is being accessed (connects to the Chip Enable pin).

D3 “Flexed” Illuminates when the USB5807/06 hub is in the Flexed state.

D4 “3V3” Indicates that the output of the 3.3V regulator is operational.

D5 “Port1 VBUS” Illuminates when 5V to downstream port 1 VBUS is present.





D10 “Port7 VBUS” Illuminates when 5V to downstream port 7 VBUS is present (EVB-USB5807 only).


D12 “5V” Indicates that the output of the 5.2V regulator is operational.

D14 “Port1 Speed/BC” In CONFIG1/CONFIG2 Modes: Indicates downstream port 1 con-nection speed.

- Off: No Connection

- Blue: USB3

- Yellow: USB2

In CONFIG5 Mode: Indicates state of GPIO70.

- Off: Tri-state

- Blue: USB3

- Yellow: USB2



- Blue: USB3

- Yellow: USB2

In CONFIG5 Mode, Indicates state of GPIO71.

- Off: Tri-state

- Blue: USB3

- Yellow: USB2



- Blue: USB3

- Yellow: USB2


- Off: Tri-state

- Blue: USB3

- Yellow: USB2





- Blue: USB3

- Yellow: USB2


- Off: Tri-state

- Blue: USB3

- Yellow: USB2



- Blue: USB3

- Yellow: USB2


- Off: Tri-state

- Blue: USB3

- Yellow: USB2



- Blue: USB3

- Yellow: USB2


- Off: Tri-state

- Blue: USB3

- Yellow: USB2

D20 “Port7 Speed/BC” USB5807 Only.In CONFIG1/CONFIG2 Modes: Indicates downstream port 7 con-nection speed.


- Blue: USB3

- Yellow: USB2


- Off: Tri-state

- Blue: USB3

- Yellow: USB2

D22 “Host Type 0” USB5806 Only.Indicates the connection speed of the upstream port when the hub is not flexed.


- Blue: USB3

- Yellow: USB2

TABLE 3-4: LED INDICATOR DESCRIPTIONS (CONTINUED)

REF.DES.

Label Description



3.1.5 EVB-USB5807/6 Switches

Table 3-5 describes the switches included on the EVB-USB5807/6.

3.1.6 EVB-USB5807/6 Connector Descriptions

Table 3-6 describes the connectors included on the PCB.

D23 “Host Type 1” USB5806 Only.Indicates the connection speed of the upstream port when the hub is flexed.


- Blue: USB3

- Yellow: USB2

D24 “Suspend” Indicates the state of the hub.

- Off: Unconfigured

- Green: Normal Operation (Running)

- Yellow: Suspended

D25 “1V2” Indicates that the output of the 1.2V regulator is operational.

D27 “RESET” Illuminates when the USB5807/06 hub is being reset via the RESET_N pin (SW3 button press).

TABLE 3-5: SWITCH DESCRIPTIONS

REF. DES. Label Description

SW1 Battery Charging Select

6-position SIP SPST switch. Selects one of the 6 battery charging strapping options.

[Default = all ports battery charging enabled]

SW2 Non-Removable Select

6-position SIP SPST switch. Selects one of the 6 non-remov-able port strapping options.

[Default = all ports non-removable]

SW3 External Reset Momentary Push-button switch to reset hub.

TABLE 3-6: EVB-USB5807/6 CONNECTOR DESCRIPTIONS

REF. DES. Type Label Description

J1 USB3.1 Type-B

Port 0 Upstream USB connection (to USB host).

J2 2x3 Header PORT0/PORT1 VBUS - Normal/Flex

Mode

Routes VBUS connections according to Flex-State.

When hub is not flexed, install shunts between [1-2] and [4-5].

When hub is flexed, install shunts between [2-3] and [5-6].

J3 1-Pin Header - Test Point for PROG_FUNC0 pin.

J4 1-Pin Header - Test Point for PROG_FUNC1 pin.

J5 1x2 Header - Install a shunt to connect the SPI ROM to the hub.

TABLE 3-4: LED INDICATOR DESCRIPTIONS (CONTINUED)

REF.DES.

Label Description



3.1.7 Test Points on EVB-USB5807/6

Table 3-7 describes the test points included on the EVB-USB5807/6. A header may be permanently installed on the through-hole test points if needed.

J6 1x4 Header CONFIG Select

Selects the configuration Mode. A shunt must be installed between 2 pins.

[1-2] - CONFIG2 Mode[2-3] - CONFIG1 Mode[3-4] - CONFIG5 ModeNo Shunt - Not Allowed

J7 1x2 Header FLEX CMD Install a shunt to force the hub into the flexed state.

J8 2x5 Header Aardvark SMBus connection compatible with “Aardvark” I2C/SPI Host Device”.

J9 2-pin Terminal

Block

12V Connection point for using lab bench 12 V power supply to power board.

J10 BC Barrel Jack

12V Connection point for DC 12V power supply.

J11 1x2 Header External Reset

Install a shunt to permanently hold hub in the reset state.

J12 USB3 Type-A Connector

PORT1 Downstream port 1 USB connection.













TABLE 3-7: EVB-USB5807/6 TEST POINT DESCRIPTIONS

REF. DES. Type Description

TP1 Test Loop (Yellow)

1.2V regulator probe point.

TP2 Test Loop (Orange)

3.3V regulator probe point.

TP3 Test Loop (Red)

12V input probe point.

TP4 Test Loop (Red)

5V regulator probe point.

TP5 Test Loop (Black)

Ground probe point.


Ground probe point.

TABLE 3-6: EVB-USB5807/6 CONNECTOR DESCRIPTIONS (CONTINUED)

REF. DES. Type Label Description




Ground probe point.


Ground probe point.

TP9 Test Loop (Blue)

5.2V Switcher probe point for PWRGD pin (pin 6).

TP10 Test Loop (Red

5.2V Switcher probe point for +VCC pin (pin 5).

TP11 Test Pad PRTCTL1 (from hub) signal probe point.






TP17 Test Pad USB5807 Only. PRTCTL7 (from hub) signal probe point.

TP18 Test Pad PROG_FUNC12 (from hub) signal probe point.

TABLE 3-7: EVB-USB5807/6 TEST POINT DESCRIPTIONS

REF. DES. Type Description



USER’S GUIDE

Appendix A. EVB-USB5807/6 Schematics

A.1 INTRODUCTION

This appendix shows the EVB-USB5807/6 Evaluation Board Schematic.


EV

B-U

SB

5807/6 Evalu

ation

Bo

ard U

ser’s Gu

ide

DS

50002543A

-page 22

2016 Microchip T

echnology Inc.

5

5

6

6

D

C

B

A

Page Title:

Project Name:

Table of Contents, Revision History, Block DiagramEVB-USB580x PN: UNG_8016

Description:

Date:Size: Sheet of RevB 1 4 A3/10/2016 Designer: Arnaldo Cruz

Elbrus Evaluation Board 1

Designed withMicrochip Technology, Inc.USB/Network Group - UNGwww.Microchip.com

EVB-USB5807Variant:Altium.com

Revision Summary Authorease to manufacturing A. Cruz

35.2V

P 1824 TO 3.3V

MCP 16125.2V TO 1.2V

k

.3V 1.2V

FIGURE A-1: EVB-USB5807/6 EVALUATION BOARD SCHEMATICS

1

1

2

2

3

3

4

4

D

C

B

A

Table of ContentsSheet Description

1 Table of Contents, Revision History, Block Diagram2 USB580x, SST26VF SPI Flash, Port Controllers, DC Regulators

Revision HistoryRevision Date

A 02-26-2016 Rel

3 USB3-A Downstream PortsMCP19035 12V to 5V DC-DC Converter4

USB3-AP1

USB3-AP2

USB3-AP3

USB3-AP4

USB3-AP5

USB3-AP6

USB3-AP7

USB580x

P1 P2 P3 P4 P5 P6 P7

MIC 2039PPC

MIC 2039PPC

MIC 2039PPC

MIC 2039PPC

MIC 2039PPC

MIC 2039PPC

USB3-BP0

FLEX

MCP 19012V TO 5

MC5.2V

DC Jac12 V

5.2V 3

Host TypeLEDs

USB Speed/BCLEDs

SST26VFSPI Flash

Flex LED

3.3V 1.2V

Flex Shunt

PROG_FUNC

25MHZ

XTAL

BC ChargingSelect Switches

Non RemovableSelect Switches

Aardvark

MIC 2039PPC

P0

EVB-USB5807

EVB-USB5806

Normal/FlexPort Power

Header

EV

B-U

SB

5807/6

Sc

hem

atics

2016

Microchip T

echnology Inc.

DS

50002543A

-page 23

5

5

6

6

D D

C C

B B

A A

Page Title:

Project Name:

USB580[6|7], SST26VF SPI Flash, DC RegulatorsEVB-USB580x PN: UNG_8016

Description:





USB3TX1_N 3USB3TX1_P 3

USB3RX1_N 3USB3RX1_P 3

USB2P1_N 3USB2P1_P 3

PRTCTL1PRTCTL2PRTCTL3PRTCTL4PRTCTL5PRTCTL6



















PRTCTL2 3PRTCTL3 3PRTCTL4 3PRTCTL5 3PRTCTL6 3PRTCTL7 3

PRTCTL1 3

PRTCTL7

Port1

Port2

Port3

Port4

Port5

Port6

Port7

USB2DN_DP1 6USB2DN_DM1 7

USB3DN_RXDP1 11USB3DN_RXDM1 12

USB3DN_TXDP1 8USB3DN_TXDM1 9



















_CTL1/LINX_DAT 70

_CTL2/LINX_CLK 62

3/LINX_ALERT_N 58

TL4/GANG_PWR 57

PRT_CTL5 52

PRT_CTL6 51

Power/OCS

Downstream P1

Downstream P2

Downstream P3

Downstream P4

Downstream P5

Downstream P6

Downstream P7

1

1

2

2

3

3

4

4

10kR11

3V3

12k1%

R24

3V3

RST_N

XTALIXTALO

0.1uFC6

0.1uFC5

330RR6

EARTH_P0

0.1uFC8

0.1uFC11

1V2

0.1uFC36

0.1uFC37

0.1uFC38

0.1uFC39

0.1uFC46

0.1uFC47

0.1uFC48

0.1uFC49

1uFC45

0.1uFC35

0.1uFC50

0.1uFC19

0.1uFC20

0.1uFC21

0.1uFC25

0.1uFC26

0.1uFC27

0.1uFC28

1uFC24

0.1uFC18

3V3

RBIAS

10kR42

5V 3V3

4.7uFC32

1kR51

Br Grn

D4

CFG

1kR44

USB3TXC0_N

USB3TXC0_P

USB3TX0_NUSB3TX0_P

USB3RX0_NUSB3RX0_P

USB2P0_NUSB2P0_P

3V3

PROG_FUNC64

10kR21

1kR183V3

200kR3

100kR2

2.2uFC1

VBUS_DET

FLEX_STATE

SUSPEND_IND4

0RR130RR14HOST_TYPE04 PF7

10kR22

200kR26

Flexed3V3

0.1uF

C29

FLEX_CMD

10RR30

0.1uFC9

200kR25

10kR29200kR27

10kR3110RR3210RR33

3V3

200kR35

10kR37200kR36

10kR3810RR3910RR40

3V3

0.01uF

C22

CFG_BC_EN

1 Prt1-7 All-Rem*2 Prt1 Non-Rem3 Prt1-2 Non-Rem4 Prt1-3 Non-Rem5 Prt1-4 Non-Rem6 Prt1-7 Non-Rem

1 No BC2 Prt1 BC3 Prt1-2 BC4 Prt1-3 BC5 Prt1-4 BC*6 Prt1-7 BC

Battery Charging Select

Non-Removable Select

10kR10

10kR5

10kR7

10kR12

3V3

100kR16

100kR17

10kR8

FSO

1 23 45 67 89 10

J8

SMBDATA

SMBCLK

10kR23

3V3

Aardvark

3V3

0.1uF

C12

FSCKFSI

FCEn

1kR19

SPI Flash Active

3V3

PROG_FUNC134PROG_FUNC144

PROG_FUNC24PROG_FUNC34PROG_FUNC44PROG_FUNC54

CFG_NON_REM

1-2 CONFIG22-3 CONFIG1*3-4 CONFIG5No shunt: not allowed

CONFIG Select

FLEX CMD

3V3 @ 500mA

ORANGE

D3

SMBDATASMBCLK

Strap Select

SPI Flash

PRTCTL7

Reset

External Reset

SMBus Interface

10pFC16

10pFC17

PROG_FUNC - [*]SPI Flash - [1-2]

J11

J5

J7

VBUS0 3

0.1uF

DNPC91

iNet Class

ClassName: Power

3V3

L1V21V2

Orange

TP2

1kR49

3V3

1V23V3

0.1uF

C94Br GrnD25

For J1 the SSTX signal pair is polarityswapped for improved routing.The same is true for the SSRX pair.

10uFC30

10kR73

3V3

12k1%

R89

86.6kR43

IB16

IC011

IC110

ID014

ID113

S1

YD 12

YC 9

YB 7

YA 4

E15 VCC 16

GND 8

IA02

IA13

IB05

PI3B3257

U5

FB3V3

BLUED2

Note:Default selections are marked with an asterisk [*].

3V3

PF0PF1

10kR9810kR99

3V3 DNPJ4

DNPJ3

SPI_CLK

SPI_DO

SPI_DI

SPI_CE_N

0.1uF

C43

5V

0.1uF

C42

0.1uFC34

1V21V2 @ 2A

Yellow

TP1

10kR46

10kR483V3

L1V2

FB1V2

470pFC95

22uF

C40

2.2uFC41

150kR50

150kR47

22uF

C33

1.5uHL1

SS6

FB 4

EN2

SNS 3VIN9

SSFB

EN

SNSVIN

AGND7

PG 5EP11

PGND10

SW 1

MIC23201

SVIN8

U16

PG1V2

GND (TAB)6

VIN2 VOUT 4

GND3 SHDN1

ADJ 5

MCP1825-ADJ

U13

23

7

45

1

6

SW1

23

7

45

1

6

SW2

VBUS 1

D- 2

D+ 3

GND 4

SSRX- 8

SSRX+ 9

GND 7

SSTX- 5

SSTX+ 6

SHLD10

SHLD11

USB3-B

J1

USB58xx_USB59xx

VBUS24

VDD1239

VDD332

USBUP_DP94 USBUP_DM95

USB3UP_RXDP99 USB3UP_RXDM100

USB3UP_TXDP96 USB3UP_TXDM97

PROG_FUNC076

PROG_FUNC173

PROG_FUNC256

PROG_FUNC360

PROG_FUNC450

PROG_FUNC571

PROG_FUNC6/TDO55

PROG_FUNC753

PROG_FUNC8/SMBCLK75

PROG_FUNC10/TMS77

PROG_FUNC11/SMBDATA74

PROG_FUNC12/PRT_CTL069

PROG_FUNC13/TDI63

PROG_FUNC14/TCK61

SPI_DO/PROG_FUNC1566

CFG_STRAP/ATEST20

TESTEN23

VDD1247

VDD1259

VDD1278

VDD1283

VDD1290

VDD1298

VDD1210

VDD1217

VDD1226

VDD1232

VDD335

VDD3327

VDD3342

VDD3354

VDD3364

VDD3372

RESET_N25

XTALI/CLKIN3

XTALO4

RBIAS1

SPI_CLK/PROG_FUNC1665

SPI_DI/CFG_BC_EN67

SPI_CE_N/CFG_NON_REM68

PRTPRT

PRT_CTLPRT_C

Upstream P0

Programmable Function I/O

SPI

FLEX_CMD21

FLEX_STATE22

Flex Control/Status

Utility

Power

Port

ePAD101

VDD3393

Clock

U1

0RR108

RSTA_N

1234

J6

Port 0

25MHz

1

Y1

1423

SW3

nCE 1SO 2nWP3

VSS4

SI 5SCK 6

nHOLD7 VDD8

SST26VF016B

U2

74LVC1G14

2 4VCC

5

GND

3

VCC

GND

C

D

C

D

U18

74LVC1G14

24 VCC

5GND

3

VCC

GND

V

G

V

G

U14

74LVC1G14

24 VCC

5

GND

3

VCC

GND

V

G

V

G

U15

3V3

0.1uF

C96

1kR110

RESET

74LVC1G14

24 VCC

5

GND

3

VCC

GND

V

G

V

G

U19

Br RedD27

VBUSP03

TP18 PROG_FUNC12

EV

B-U

SB

5807/6 Evalu

ation

Bo

ard U

ser’s Gu

ide

DS

50002543A

-page 24

2016 Microchip T

echnology Inc.

5

5

6

6

D

C

B

A

Page Title:

Project Name:

USB3-A Downstream PortsEVB-USB580x PN: UNG_8016

Description:





0.1uFC54

0.1uFC52

USB3TXC5_P

USB3TXC5_N

USB3RX5_NUSB3RX5_P

USB2P5_NUSB2P5_P

USB3TX5_NUSB3TX5_P

VBUS5

0.1uFC62

0.1uFC60

USB3TXC6_P

USB3TXC6_N

USB3RX6_NUSB3RX6_P

USB2P6_NUSB2P6_P

USB3TX6_NUSB3TX6_P

VBUS6

0.1uFC70

0.1uFC68

USB3TXC7_P

USB3TXC7_N

USB3RX7_NUSB3RX7_P

USB2P7_NUSB2P7_P

USB3TX7_NUSB3TX7_P

VBUS7

1kR53

Br Grn

D6

A

1kR57

Br Grn

D8

1kR61

Br Grn

D10

A

VBUS5

VBUS6

VBUS7

137R34

137R41

137R45

Note:Default selections are marked with an asterisk [*].

1kDNP

R101

1kDNP

R103

1kDNP

R105

47uFC56

47uFC64

47uFC72

330RR55

PORT5

0.1uFC58

EARTH_P5

VBUS1

D-2

D+3

GND4

SSRX-5

SSRX+6

GND7

SSTX-8

SSTX+9

SHLD 10

SHLD 11

GSB311131HR

J16

330RR59

PORT6

0.1uFC66

EARTH_P6

VBUS1

D-2

D+3

GND4

SSRX-5

SSRX+6

GND7

SSTX-8

SSTX+9

SHLD 10

SHLD 11

GSB311131HR

J17

330RR63

PORT7

0.1uFC74

EARTH_P7

VBUS1

D-2

D+3

GND4

SSRX-5

SSRX+6

GND7

SSTX-8

SSTX+9

SHLD 10

SHLD 11

GSB311131HR

J18

SP0 2

1

1

2

2

3

3

4

4

D

C

B

A

0.1uFC53

0.1uFC51

USB3TXC1_P

USB3TXC1_N

USB3RX1_NUSB3RX1_P

USB2P1_NUSB2P1_P

USB3TX1_NUSB3TX1_PUSB3TX1_N2

USB3TX1_P2

USB3RX1_N2USB3RX1_P2

USB2P1_N2USB2P1_P2

VBUS1

1kR52

VBUS1Br Grn

D5

0.1uFC61

0.1uFC59

USB3TXC2_P

USB3TXC2_N

USB3RX2_NUSB3RX2_P

USB2P2_NUSB2P2_P


USB3TX2_P2


USB2P2_N2USB2P2_P2

VBUS2

0.1uFC69

0.1uFC67

USB3TXC3_P

USB3TXC3_N

USB3RX3_NUSB3RX3_P

USB2P3_NUSB2P3_P


USB3TX3_P2


USB2P3_N2USB2P3_P2

VBUS3

0.1uFC76

0.1uFC75

USB3TXC4_P

USB3TXC4_N

USB3RX4_NUSB3RX4_P

USB2P4_NUSB2P4_P


USB3TX4_P2


USB2P4_N2USB2P4_P2

VBUS4

USB3TX5_N2USB3TX5_P2


USB2P5_N2USB2P5_P2



USB2P6_N2USB2P6_P2



USB2P7_N2USB2P7_P2

5V

2.1APRTCTL12

1kR56

Br Grn

D75V

2.1APRTCTL22

1kR60

Br Grn

D95V

2.1APRTCTL32

1kR64

Br Grn

D115V

2.1APRTCTL42

5V

2.1PRTCTL52

5V

2.1APRTCTL62

5V

2.1PRTCTL72

USB3 Downstream Port 1







VBUS2

VBUS3

VBUS4

PORT0/PORT1 VBUS -- Normal/Flex Mode

VBUS02

0RR92

0RR90

0RR94

0RR96

0RR91

0RR93

0RR95

137R9

137R15

137R20

137R28

1kDNP

R100

1kDNP

R102

1kDNP

R104

1kDNP

R107

47uFC7

47uFC10

47uFC13

47uFC14

47uFC15

47uFC23

47uFC31

47uFC63

47uFC55

47uFC71

47uFC77

GND 5

VIN6

EN4

FAULTn3

VOUT 1

ILIMIT 2

MIC2039_DFN6

ePAD 7

U6

GND 5

VIN6

EN4

FAULTn3

VOUT 1

ILIMIT 2

MIC2039_DFN6

ePAD 7

U7

GND 5

VIN6

EN4

FAULTn3

VOUT 1

ILIMIT 2

MIC2039_DFN6

ePAD 7

U8

GND 5

VIN6

EN4

FAULTn3

VOUT 1

ILIMIT 2

MIC2039_DFN6

ePAD 7

U9

GND 5

VIN6

EN4

FAULTn3

VOUT 1

ILIMIT 2

MIC2039_DFN6

ePAD 7

U10

GND 5

VIN6

EN4

FAULTn3

VOUT 1

ILIMIT 2

MIC2039_DFN6

ePAD 7

U11

GND 5

VIN6

EN4

FAULTn3

VOUT 1

ILIMIT 2

MIC2039_DFN6

ePAD 7

U12

330RR54

PORT1

0.1uFC57

EARTH_P1

VBUS1

D-2

D+3

GND4

SSRX-5

SSRX+6

GND7

SSTX-8

SSTX+9

SHLD 10

SHLD 11

GSB311131HR

J12

330RR58

PORT2

0.1uFC65

EARTH_P2

VBUS1

D-2

D+3

GND4

SSRX-5

SSRX+6

GND7

SSTX-8

SSTX+9

SHLD 10

SHLD 11

GSB311131HR

J13

330RR62

PORT3

0.1uFC73

EARTH_P3

VBUS1

D-2

D+3

GND4

SSRX-5

SSRX+6

GND7

SSTX-8

SSTX+9

SHLD 10

SHLD 11

GSB311131HR

J14

330RR65

PORT4

0.1uFC78

EARTH_P4

VBUS1

D-2

D+3

GND4

SSRX-5

SSRX+6

GND7

SSTX-8

SSTX+9

SHLD 10

SHLD 11

GSB311131HR

J15

TP12

TP13

TP14

TP11 TP15

TP16

TP17

123456

J2VBUS0VBUSP1VBUSP0

VBUS1

VBUSP1

Normal Mode-------------------[1-2] VBUS0 -- VBUSP0*[4-5] VBUSP1 -- VBUS1*

Flex Mode-------------------[2-3] VBUS0 -- VBUSP1[5-6] VBUSP0 -- VBUS1

VBU

EV

B-U

SB

5807/6

Sc

hem

atics

2016

Microchip T

echnology Inc.

DS

50002543A

-page 25

5

5

6

6

D D

C C

B B

A A

Page Title:

Project Name:

12V to 5V DC supply, BC/Host Type/Suspend LEDsEVB-USB580x PN: UNG_8016

Description:





Blue =USB3 HostYellow=USB2 Host

1

13

BLU

E

42 1

3

YE

LLO

W

BLU

E

D20

YE

LLO

W

5V @ 15A5V

100uFC83

100uFC84

0RR68 Br Grn

D12

V

100uFC85

iPower

DC12V

5V

RedTP4

5V

5VL

2.2kR70

0.1uFC93

FID1

MH1MTHOLE 4-40 120DL 220PAD

MH2 MH3 MH4

FiducialsFID2 FID3

FID4 FID5 FID6

Mounting Holes

i Top LayerFID1 FID2 FID3

i Bottom LayerFID4 FID5 FID6

Port7 Speed/BCd/BC

1

1

2

2

3

3

4

4

MMBD914LT1G

D13

330RR79330RR80330RR81

3V3

330RR82330RR84PROG_FUNC62

0RR86

0RR83

HOST_TYPE1

SPEED_BC_IND7

330RR78330RR77

MMBD914LT1G

D213V3

330RR87330RR85

330RR88SUSPEND_IND2

HOST_TYPE02

PROG_FUNC22PROG_FUNC32PROG_FUNC42PROG_FUNC52

PROG_FUNC132PROG_FUNC142

SPEED_BC_IND1SPEED_BC_IND2SPEED_BC_IND3SPEED_BC_IND4SPEED_BC_IND5SPEED_BC_IND6

Host Type 0

Green =RunYellow=Suspend

Host TypeSuspend

Blue =USB3/BCYellow=USB2/BC1.2CONFIG5=BC Indicator

Black

TP5

Black

TP6

Black

TP7

Black

TP8

42 1

3

YE

LLO

W

BLU

E

D14

42 1

3

YE

LLO

W

BLU

E

D15

42 1

3

YE

LLO

W

BLU

E

D16

42 1

3

YE

LLO

W

BLU

E

D17

42 1

3

YE

LLO

W

BLU

E

D18

42

YE

LLO

W

D19

421

3

YE

LLO

W

BLU

E

D22

421

3B

LUE

D23

421

3

YE

LLO

W

GR

EE

N

D24

100kR72

20kR74

750RR75680pFC90

2.61kR76

DC12V

33pFC873900pFC86 8.2kR69

0RR66

51kR71

140kR67

D

G

S

MCP87050Q1

0.33uFC82

4

1,2,3

5,6,7,8

MCP87022Q2

12V

5

Switching 12VDC to 5VDC Supply

L5V

FB5V

RedTP3

EARTH_DC

330RR97

5VL

Blue

TP9

PG5V

DC Jack-8A

132SH

J10

i Power

i Power

RedTP10

For use withbench supply

73.2kR143

0RR142

Output Voltage0R out - 5.20V0R in - 5.36V

47uF

C79

47uF

C81

47uF

C92

20R

R141

4.7μF

C89

0.1uFC440.1uFC80

0.1uFC88

D26

TERM_BLOCK_2P

2

1J9

2uHL2

BOOT 8

FB 2

VIN4

COMP 3

SHDN1

+VCC 6

HDRV 10

PWRGD 5

LDRV 7

PHASE 9

ePAD (GND)11

MCP19035

U17

LED_V1

LED_V2

Port1 Speed/BC Port2 Speed/BC Port3 Speed/BC Port4 Speed/BC Port5 Speed/BC Port6 Spee


USER’S GUIDE

Appendix B. EVB-USB5807/6 BOM

B.1 INTRODUCTION

This appendix shows the EVB-USB5807/6 Evaluation Bill of Materials.


EV

B-U

SB

5807/6 BO

M

2016

Microchip T

echnology Inc.

DS

50002543A

-page 27

TA

Manufacturer Part NumberGRM188R71A225KE15D

GRM155R71C104KA88D

GRM32ER61C476KE15K

GRM1555C1H100JZ01D

C0603C103M5RAC

ECJ-1VB0J105K

GRM21BR61C106KE15L

LMK107BJ475KA-T

an CL31B226KPHNNNE

GRM188R71C334KA01D

LMK325BJ107MM-T

C1608C0G1H392J080AA

GMC10CG330J50NTLF

an CL21A475KBQNNNE

ECJ-1VC1H681J

GRM155R71C104KA88D

06033A471JAT2A

LTST-C193TBKT-5A

LTST-C190KFKT

BLE B-1: EVB-USB5807/6 BILL OF MATERIALS

Item Qty Reference Designator(s) Description Manufacturer1 2 C1, C41 CAP CER 2.2uF 10V 10% X7R SMD

0603Murata

2 55 C5, C6, C8, C9, C11, C12, C18, C19, C20, C21, C25, C26, C27, C28, C29, C34, C35, C36, C37, C38, C39, C42, C43, C44, C46, C47, C48, C49, C50, C51, C52, C53, C54, C57, C58, C59, C60, C61, C62, C65, C66, C67, C68, C69, C70, C73, C74, C75, C76, C78, C80, C88, C93, C94, C96

CAP CER 0.1uF 16V 10% X7R SMD 0402

Murata

3 17 C7, C10, C13, C14, C15, C23, C31, C55, C56, C63, C64, C71, C72, C77, C79, C81, C92

Capacitor, 47uF, 16V, 10%, X5R, 1210 Murata

4 2 C16, C17 CAP CER 10pF 50V 5% NP0 SMD 0402 Murata

5 1 C22 CAP CER 0.01uF 50V 20% X7R SMD 0603

KEMET

6 2 C24, C45 CAP CER 1uF 6.3V 10% X5R SMD 0603 Panasonic

7 1 C30 CAP CER 10uF 16V 10% X5R SMD 0805

Murata


Taiyo Yuden

9 2 C33, C40 CAP CER 22uF 10V 10% X7R SMD 1206

Samsung Electro-Mech


Murata

11 3 C83, C84, C85 CAP CER 100uF 10V 20% X5R SMD 1210

Taiyo Yuden

12 1 C86 CAP CER 3900pF 50V 5% C0G SMD 0603

TDK

13 1 C87 CAP CER 33pF 50V 5% NP0 SMD 0603 Cal-Chip

14 1 C89 CAP CER 4.7UF 50V 0805 Samsung Electro-Mech

15 1 C90 CAP CER 680pF 50V 5% NP0 SMD 0603

Panasonic


Murata

17 1 C95 CAP CER 470pF 25V 5% NP0 SMD 0603

AVX

18 1 D2 DIO LED BLUE 2.8V 20mA 15mcd Clear SMD 0603

Lite-On

19 1 D3 DIO LED ORANGE 2V 30mA 90mcd Clear SMD 0603

Lite-On

EV

B-U

SB

5807/6 Evalu

ation

Bo

ard U

ser’s Gu

ide

DS

50002543A

-page 28

2016 Microchip T

echnology Inc.

LTST-C191KGKT

LTST-C191KGKT

MMBD914LT1G

LTST-C195TBKSKT-5A

LTST-C195KGJSKT

MMBD914-7-F

LTST-C191KRKT

cial ProGSB4211311WEU

TSW-102-07-G-T

TSW-101-07-G-S

TSW-102-07-G-S

TSW-104-07-G-S

TSW-105-07-G-D

282836-2

PJ-063BH

cial ProGSB311131HR

LQH5BPN1R5NT0L

7443551200

MCP87050T-U/MF

gy MCP87022T-U/MF

MCT06030C1003FP500

CRCW0603200KFKEA

CRCW060310K0FKEA

ERJ-3EKF3300V

ic ComERJ-3EKF1370V

20 9 D4, D5, D6, D7, D8, D9, D10, D11, D25 LED, Bright Green, 0603 Lite-On

21 1 D12 LED, Bright Green, 0603 Lite-On

22 2 D13, D21 Diode, MMBD914LT, Fast Switching, 100VDC, 200mA, SOT-23

ON Semiconductor

23 7 D14, D15, D16, D17, D18, D19, D20 DIO LED BLUE, YELLOW 2.9V, 2.0V 5mA 0605

Lite-On

24 1 D24 DIO LED DUAL, GREEN/YELLOW 2.0V, 2.0V 5mA 0605

Lite-On

25 1 D26 DIODE SWITCHING 75V 0.2A SOT-23 Diodes Inc.

26 1 D27 LED, Bright Red, 0603 Lite-On

27 1 J1 USB 3.1 RCPT TYPE B R/A TH Amphenol Commer

28 1 J2 CON HDR 2.54MM MALE 3x2 TH GOLD 5.84MH TH VERT

SAMTEC

29 2 J3, J4 CONN HEADER 1POS .100" SGL GOLD Samtec

30 3 J5, J7, J11 CONN HEADER 2POS .100" SGL GOLD Samtec

31 1 J6 CON HDR-2.54 MALE 1x4 GOLD 5.84MH TH VERT

Samtec Inc

32 1 J8 HDR 10POS .100" SGL GOLD Samtec Inc.

33 1 J9 Terminal Block 5.0MM PCB MOUNT 2P TE Connectivity

34 1 J10 CONN PWR JACK 2.5X6.5MM, 8A CUI Inc

35 7 J12, J13, J14, J15, J16, J17, J18 CON USB 3.0 STD-A RCPT TH R/A Amphenol Commer

36 1 L1 Power Inductor 1.5uH 30% 3A, 24mOhms

Murata Electronics

37 1 L2 Power Inductor 2 uH 20% 23A, 2.6mOhms

Wurth Electronics

38 1 Q1 MCHP ANALOG MOSFET N-CH 25V 100A 0.006R MCP87050-U/MF PDFN-8

Microchip

39 1 Q2 MCHP ANALOG MOSFET N-CH 25V 100A 0.0026R MCP87022T-U/MF PDFN-8

Microchip Technolo

40 4 R2, R16, R17, R72 RES TF 100k 1% 1/8W SMD 0603 Vishay

41 6 R3, R25, R26, R27, R35, R36 RES TKF 200k 1% 1/10W SMD 0603 Vishay

42 19 R5, R7, R8, R10, R11, R12, R21, R22, R23, R29, R31, R37, R38, R42, R46, R48, R73, R98, R99

RES TKF 10k 1% 1/10W SMD 0603 Vishay

43 17 R6, R54, R55, R58, R59, R62, R63, R65, R77, R78, R79, R80, R81, R82, R84, R88, R97

RES TKF 330R 1% 1/10W SMD 0603 Panasonic

44 7 R9, R15, R20, R28, R34, R41, R45 RES 137R 1% 1/10W 0603 Panasonic Electron

EV

B-U

SB

5807/6 BO

M

2016

Microchip T

echnology Inc.

DS

50002543A

-page 29

NRC06Z0TRF

ERJ-3EKF1001V

RC0603FR-0712KL

ERJ-3EKF10R0V

mpERJ-3EKF8662V

ERJ-3EKF1503V

ERJ-3EKF1403V

ERJ-3EKF8201V

ERJ-3EKF2201V

ERJ-3EKF5102V

9C06031A2002FKHFT

CRCW0603750RFKEA

MC 0.063W 0603 1% 2K61

ERJ-3EKF1001V

ERJ-3EKF20R0V

ERJ-3EKF7322V

SPA06B

CKN10502CT-ND

5004

5003

5000

5001

5117

USB58xx_USB59xx

SST26VF016B-104I/SM

PI3B3257QE

MIC2039AYMT

MCP1825T-ADJE/DC

45 13 R14, R66, R68, R83, R90, R91, R92, R93, R94, R95, R96, R108, R142

RES TKF 0R 1/10W SMD 0603 NIC Components

46 13 R18, R19, R44, R49, R51, R52, R53, R56, R57, R60, R61, R64, R110

RES TKF 1k 1% 1/10W SMD 0603 Panasonic

47 2 R24, R89 RES TKF 12k 1% 1/10W SMD 0603 Yageo

48 5 R30, R32, R33, R39, R40 RES TKF 10R 1% 1/10W SMD 0603 Panasonic

49 1 R43 RES TKF 86.6K 1% 1/10W SMD 0603 Pansonic Electronic Co

50 2 R47, R50 RES TKF 150k 1% 1/10W SMD 0603 Panasonic

51 1 R67 RES TKF 140k 1% 1/10W SMD 0603 Panasonic

52 1 R69 RES TKF 8.2k 1% 1/10W SMD 0603 Panasonic


54 1 R71 RES TKF 51k 1% 1/10W SMD 0603 Panasonic

55 1 R74 RES TKF 20k 1% 1/10W SMD 0603 Yageo

56 1 R75 RES TKF 750R 1% 1/10W SMD 0603 Vishay

57 1 R76 RES TKF 2.61k 1% 1/16W SMD 0603 MULTICOMP

58 7 R100, R101, R102, R103, R104, R105, R107 RES TKF 1k 1% 1/10W SMD 0603 Panasonic

59 1 R141 RES TKF 20R 1% 1/10W SMD 0603 Panasonic


61 2 SW1, SW2 Switch SIP SPST 6POS Vertical, Unshielded, 20V

C&K Components

62 1 SW3 SWITCH TACTILE SPST-NO 0.05A 16V C&K Components

63 1 TP1 TEST POINT PC MINI .040"D YELLOW Keystone Electronics

64 1 TP2 TEST POINT PC MINI .040"D ORANGE Keystone Electronics

65 3 TP3, TP4, TP10 TEST POINT PC MINI .040"D RED Keystone Electronics

66 4 TP5, TP6, TP7, TP8 TEST POINT PC MINI .040"D BLACK Keystone Electronics

67 1 TP9 TEST POINT PC MINIATURE T/H BLUE Keystone Electronics

68 1 U1 IC, USB58xx, USB59xx, 7 Port USB 3.1 Gen1 Hub, QFN100

Microchip Technology

69 1 U2 Flash Serial, SPI, 2.7-3.6V, x1/x2/x4, SOIC8


70 1 U5 Quad, 2:1 Mux/Demux FET BusSwitch Pericom

71 7 U6, U7, U8, U9, U10, U11, U12 USB Switch ICs ADJ, High-Side, Power Distribution Switch, DFN-6 pkg

Micrel

72 1 U13 IC, LDO ADJ, 2.3 to 6Vin, 0.8V to 5V out, 0.5A


EV

B-U

SB

5807/6 Evalu

ation

Bo

ard U

ser’s Gu

ide

DS

50002543A

-page 30

2016 Microchip T

echnology Inc.

ed 74LVC1G14SE-7

logy (MicMIC23201YML

logy MCP19035BAABE/MF

ABM8G-25.000MHZ-B4Y-T

73 4 U14, U15, U18, U19 IC BUFF 74LVC1G14SE-7 SNGL SOT-553

Diodes Incorporat

74 1 U16 IC, 2.7V to 5.5V input, 2A, Synchronous 2MHz Buck Regulator

Microchip Techno

75 1 U17 IC, 4.5V to 30V input, 20A, 600kHz Buck Controller, power good signal

Microchip Techno

76 1 Y1 Crystal 25MHz 4 pins 3225 ABRACON


USER’S GUIDE

Appendix C. USB5807/06 PCB Silk Screens

C.1 INTRODUCTION

This appendix shows the USB5807/06 Top and Bottom Silk Screen Images.

FIGURE C-1: USB5807/06 TOP AND BOTTOM SILK SCREEN IMAGES



FIGURE C-2: USB5807/06 BOTTOM SILK SCREEN IMAGE



AMERICASCorporate Office2355 West Chandler Blvd.Chandler, AZ 85224-6199Tel: 480-792-7200 Fax: 480-792-7277Technical Support: http://www.microchip.com/supportWeb Address: www.microchip.com

AtlantaDuluth, GA Tel: 678-957-9614 Fax: 678-957-1455

Austin, TXTel: 512-257-3370

BostonWestborough, MA Tel: 774-760-0087 Fax: 774-760-0088

ChicagoItasca, IL Tel: 630-285-0071 Fax: 630-285-0075

ClevelandIndependence, OH Tel: 216-447-0464 Fax: 216-447-0643

DallasAddison, TX Tel: 972-818-7423 Fax: 972-818-2924

DetroitNovi, MI Tel: 248-848-4000

Houston, TX Tel: 281-894-5983

IndianapolisNoblesville, IN Tel: 317-773-8323Fax: 317-773-5453

Los AngelesMission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608

New York, NY Tel: 631-435-6000

San Jose, CA Tel: 408-735-9110

Canada - TorontoTel: 905-695-1980 Fax: 905-695-2078

ASIA/PACIFICAsia Pacific OfficeSuites 3707-14, 37th FloorTower 6, The GatewayHarbour City, Kowloon

Hong KongTel: 852-2943-5100Fax: 852-2401-3431

Australia - SydneyTel: 61-2-9868-6733Fax: 61-2-9868-6755

China - BeijingTel: 86-10-8569-7000 Fax: 86-10-8528-2104

China - ChengduTel: 86-28-8665-5511Fax: 86-28-8665-7889

China - ChongqingTel: 86-23-8980-9588Fax: 86-23-8980-9500

China - DongguanTel: 86-769-8702-9880

China - GuangzhouTel: 86-20-8755-8029

China - HangzhouTel: 86-571-8792-8115 Fax: 86-571-8792-8116

China - Hong Kong SARTel: 852-2943-5100 Fax: 852-2401-3431

China - NanjingTel: 86-25-8473-2460Fax: 86-25-8473-2470

China - QingdaoTel: 86-532-8502-7355Fax: 86-532-8502-7205

China - ShanghaiTel: 86-21-5407-5533 Fax: 86-21-5407-5066

China - ShenyangTel: 86-24-2334-2829Fax: 86-24-2334-2393

China - ShenzhenTel: 86-755-8864-2200 Fax: 86-755-8203-1760

China - WuhanTel: 86-27-5980-5300Fax: 86-27-5980-5118

China - XianTel: 86-29-8833-7252Fax: 86-29-8833-7256

ASIA/PACIFICChina - XiamenTel: 86-592-2388138 Fax: 86-592-2388130

China - ZhuhaiTel: 86-756-3210040 Fax: 86-756-3210049

India - BangaloreTel: 91-80-3090-4444 Fax: 91-80-3090-4123

India - New DelhiTel: 91-11-4160-8631Fax: 91-11-4160-8632

India - PuneTel: 91-20-3019-1500

Japan - OsakaTel: 81-6-6152-7160 Fax: 81-6-6152-9310

Japan - TokyoTel: 81-3-6880- 3770 Fax: 81-3-6880-3771

Korea - DaeguTel: 82-53-744-4301Fax: 82-53-744-4302

Korea - SeoulTel: 82-2-554-7200Fax: 82-2-558-5932 or 82-2-558-5934

Malaysia - Kuala LumpurTel: 60-3-6201-9857Fax: 60-3-6201-9859

Malaysia - PenangTel: 60-4-227-8870Fax: 60-4-227-4068

Philippines - ManilaTel: 63-2-634-9065Fax: 63-2-634-9069

SingaporeTel: 65-6334-8870Fax: 65-6334-8850

Taiwan - Hsin ChuTel: 886-3-5778-366Fax: 886-3-5770-955

Taiwan - KaohsiungTel: 886-7-213-7828

Taiwan - TaipeiTel: 886-2-2508-8600 Fax: 886-2-2508-0102

Thailand - BangkokTel: 66-2-694-1351Fax: 66-2-694-1350

EUROPEAustria - WelsTel: 43-7242-2244-39Fax: 43-7242-2244-393

Denmark - CopenhagenTel: 45-4450-2828 Fax: 45-4485-2829

France - ParisTel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79

Germany - DusseldorfTel: 49-2129-3766400

Germany - KarlsruheTel: 49-721-625370

Germany - MunichTel: 49-89-627-144-0 Fax: 49-89-627-144-44

Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781

Italy - VeniceTel: 39-049-7625286

Netherlands - DrunenTel: 31-416-690399 Fax: 31-416-690340

Poland - WarsawTel: 48-22-3325737

Spain - MadridTel: 34-91-708-08-90Fax: 34-91-708-08-91

Sweden - StockholmTel: 46-8-5090-4654

UK - WokinghamTel: 44-118-921-5800Fax: 44-118-921-5820

Worldwide Sales and Service

06/23/16

http://support.microchip.com

http://www.microchip.com

Date post:	14-Mar-2018
Category:	Documents
Upload:	phungcong
View:	264 times
Download:	13 times