+ All Categories
Home > Documents > Extrudex Aluminum - Standard Shapes · PDF fileExtrudex Aluminum Corp. 411 Chrislea Road...

Extrudex Aluminum - Standard Shapes · PDF fileExtrudex Aluminum Corp. 411 Chrislea Road...

Date post: 15-Feb-2018
Category:
Upload: phamdang
View: 214 times
Download: 0 times
Share this document with a friend
55
http://www.extrudex.com LOCATIONS: Extrudex Aluminum Corp. 411 Chrislea Road Woodbridge, Ontario Canada L4L 8N4 Tel: (416) 745-4444 Fax: (416) 745-0925 Toll Free: 1-800-668-7210 Extrudex Aluminum Inc. 12051 Mahoning Ave Box 697 North Jackson, Ohio USA 44451 Tel: (330) 538-4444 Tel: (330) 538-4450 Toll Free: 1-800-430-0006 Extrudex Aluminum (Quebec) Inc. 770 Chemin Oliver Bernieres, Quebec Canada G7A 2N2 Tel: (418) 831-4444 Fax: (418) 831-7400 Toll Free: 1-800-704-4244 Container Size: 7", 8", 10" and 13" 8" and 10" 7" and 8" Stretching Capacity: 25 Lbs/Ft 15 Lbs/Ft Alloys: 6063, 6061, 6351, 6005 6063, 6061, 6351, 6005 6063, 6061, 6005 Chemical composition and tolerance charts are included with permission from "The Aluminum Association Inc., 900 19th St., N.W. Washington, D.C. 20006" Revised on: February 08, 2018
Transcript

http://www.extrudex.com

LOCATIONS:

Extrudex Aluminum Corp.

411 Chrislea Road

Woodbridge, Ontario

Canada

L4L 8N4

Tel: (416) 745-4444

Fax: (416) 745-0925

Toll Free: 1-800-668-7210

Extrudex Aluminum Inc.

12051 Mahoning Ave

Box 697

North Jackson, Ohio

USA 44451

Tel: (330) 538-4444

Tel: (330) 538-4450

Toll Free: 1-800-430-0006

Extrudex Aluminum (Quebec) Inc.

770 Chemin Oliver

Bernieres, Quebec

Canada

G7A 2N2

Tel: (418) 831-4444

Fax: (418) 831-7400

Toll Free: 1-800-704-4244

Container Size:

7", 8", 10" and 13" 8" and 10" 7" and 8"

Stretching Capacity:

25 Lbs/Ft 15 Lbs/Ft

Alloys:

6063, 6061, 6351, 6005 6063, 6061, 6351, 6005 6063, 6061, 6005

Chemical composition and tolerance charts are included with permission from

"The Aluminum Association Inc., 900 19th St., N.W. Washington, D.C. 20006"

Revised on: February 08, 2018

Rectangular BarsSquare Edges

http://www.extrudex.com

Dim. (T)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-2133 0.437 0.312 0.240 à 0.161

S-4481 0.500 0.125 0.109 P 0.073

S-2979 0.500 0.187 0.164 P P 0.110

S-23972 0.500 0.250 0.210 P 0.148

S-2134 0.500 0.375 0.329 P 0.221

S-6347 0.625 0.125 0.137 P 0.092

S-26175 0.625 0.250 0.274 P 0.184

S-2135 0.625 0.375 0.411 P 0.276

S-23105 0.625 0.500 0.548 P 0.369

S-5567 0.750 0.094 0.125 P 0.084

S-4642 0.750 0.125 0.165 P P 0.111

S-2381 0.750 0.187 0.246 P P 0.165

S-22340 0.750 0.250 0.329 P 0.221

S-27823 0.750 0.375 0.494 P 0.332

S-4767 0.750 0.500 0.659 P P 0.442

S-5563 0.875 0.120 0.184 P 0.124

S-22060 0.875 0.125 0.192 P 0.129

S-4525 1.000 0.123 0.216 P 0.145

S-2234 1.000 0.125 0.220 P P 0.148

S-4526 1.000 0.185 0.325 P 0.218

S-2231 1.000 0.187 0.329 P P 0.221

S-2125 1.000 0.250 0.439 P P 0.295

S-22329 1.000 0.312 0.548 P 0.368

S-2222 1.000 0.375 0.659 P P 0.443

S-2224 1.000 0.500 0.878 P P 0.590

S-2491 1.000 0.625 1.098 P P 0.738

S-2444 1.000 0.750 1.317 P P 0.885

S-24127 1.125 0.100 0.197 P 0.133

S-5598 1.125 0.165 0.324 P 0.218

S-25702 1.125 0.750 1.481 P 0.995

S-12343 1.125 1.000 1.975 P 1.327

S-4900 1.250 0.123 0.270 P 0.182

S-2351 1.250 0.125 0.274 P P 0.184

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular BarsSquare Edges

http://www.extrudex.com

Dim. (T)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-4527 1.250 0.182 0.400 P 0.269

S-3513 1.250 0.188 0.412 P P 0.277

S-22148 1.250 0.200 0.439 P 0.295

S-2349 1.250 0.250 0.549 P P 0.369

S-4766 1.250 0.375 0.824 P P 0.553

S-2579 1.250 0.500 1.098 P P 0.738

S-2578 1.250 0.750 1.647 P P 1.107

S-12392 1.250 1.000 2.195 P P 1.475

S-2635 1.375 0.220 0.515 P 0.344

S-22342 1.375 1.000 2.414 P 1.622

S-2327 1.437 0.250 0.631 P 0.424

S-4674 1.500 0.123 0.325 P 0.218

S-2254 1.500 0.125 0.330 P P 0.222

S-4600 1.500 0.185 0.488 P P 0.328

S-2181 1.500 0.187 0.494 P P 0.332

S-2076 1.500 0.250 0.659 P P 0.443

S-2229 1.500 0.375 0.988 P P 0.664

S-2396 1.500 0.500 1.317 P P 0.885

S-4969 1.500 0.750 1.976 P P 1.327

S-4654 1.500 1.000 2.634 P P 1.770

S-4676 1.500 1.250 3.293 P P 2.213

S-26762 1.550 1.300 3.538 P 2.377

S-20806 1.625 0.250 0.713 P 0.479

S-2916 1.750 0.125 0.384 P P 0.258

S-4889 1.750 0.185 0.569 P 0.382

S-4801 1.750 0.188 0.577 P P 0.388

S-2398 1.750 0.250 0.769 P P 0.517

S-9312 1.750 0.438 1.345 P 0.904

S-2331 1.750 0.500 1.537 P P 1.033

S-9964 1.750 0.750 2.304 P P 1.548

S-24252 1.750 1.000 3.073 P 2.065

S-23324 1.750 1.375 4.220 P 2.835

S-2233 2.000 0.125 0.439 P P 0.295

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular BarsSquare Edges

http://www.extrudex.com

Dim. (T)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-5269 2.000 0.185 0.650 P 0.437

S-2230 2.000 0.187 0.656 P P 0.441

S-2226 2.000 0.250 0.878 P P 0.590

S-2223 2.000 0.375 1.317 P P 0.885

S-2221 2.000 0.500 1.756 P P 1.180

S-23874 2.000 0.625 2.195 P P 1.475

S-2436 2.000 0.750 2.634 P P 1.770

S-7238 2.000 1.000 3.512 P P 2.360

S-12342 2.000 1.125 3.951 P 2.655

S-22772 2.000 1.250 4.390 P P 2.950

S-4659 2.000 1.500 5.268 P P 3.540

S-9343 2.130 1.000 3.740 P 2.513

S-5215 2.250 0.185 0.731 P 0.491

S-4090 2.250 0.188 0.743 P 0.499

S-2615 2.250 0.250 0.988 P P 0.664

S-21464 2.250 0.375 1.481 P P 0.995

S-6573 2.362 0.984 4.081 P 2.742

S-24517 2.500 0.125 0.549 P 0.369

S-5268 2.500 0.185 0.813 P 0.546

S-4091 2.500 0.188 0.826 P P 0.555

S-2455 2.500 0.250 1.098 P P 0.738

S-16069 2.500 0.345 1.514 P 1.018

S-2325 2.500 0.375 1.647 P P 1.107

S-4651 2.500 0.500 2.195 P P 1.475

S-13590 2.500 0.750 3.292 P à 2.212

S-4655 2.500 1.000 4.390 P P 2.950

S-19141 2.500 1.250 5.487 P P 3.687

S-4660 2.500 1.500 6.585 P P 4.425

S-23922 2.500 2.000 8.780 P 5.900

S-25964 2.500 2.250 9.877 P 6.637

S-5206 2.750 0.125 0.604 P 0.406

S-21463 2.750 0.250 1.207 P P 0.811

S-2490 2.750 0.375 1.811 P 1.217

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular BarsSquare Edges

http://www.extrudex.com

Dim. (T)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-26761 2.750 2.000 9.658 P 6.490

S-20793 2.750 2.375 11.469 P 7.707

S-20794 2.875 2.500 12.621 P 8.481

S-2155 2.937 0.081 0.418 P 0.281

S-2225 3.000 0.125 0.659 P P 0.443

S-2220 3.000 0.187 0.985 P P 0.662

S-2168 3.000 0.250 1.317 P P 0.885

S-2218 3.000 0.375 1.976 P P 1.328

S-2216 3.000 0.500 2.634 P P 1.770

S-15161 3.000 0.625 3.292 P 2.212

S-2313 3.000 0.750 3.951 P P 2.655

S-21121 3.000 0.875 4.609 P 3.097

S-4656 3.000 1.000 5.268 P P 3.540

S-15281 3.000 1.250 6.585 P P 4.425

S-4769 3.000 1.500 7.902 P P 5.310

S-20398 3.000 1.750 9.219 P P 6.195

S-7354 3.000 2.000 10.536 P P 7.080

S-21519 3.000 2.250 11.853 P 7.965

S-26187 3.000 2.500 13.170 P 8.850

S-8399 3.375 0.188 1.113 P P 0.748

S-16731 3.375 0.250 1.481 P 0.995

S-20820 3.375 1.875 11.112 P 7.467

S-6698 3.500 0.095 0.583 P 0.392

S-3469 3.500 0.187 1.150 P P 0.773

S-2450 3.500 0.250 1.537 P P 1.033

S-14971 3.500 0.375 2.304 P P 1.549

S-22691 3.500 0.500 3.075 P P 2.065

S-2314 3.500 0.625 3.842 P 2.582

S-22164 3.500 0.750 4.609 P P 3.097

S-22165 3.500 1.000 6.146 P P 4.130

S-22836 3.500 1.500 9.219 P P 6.195

S-22166 3.500 2.000 12.292 P 8.260

S-22433 3.500 2.000 12.292 P 8.260

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular BarsSquare Edges

http://www.extrudex.com

Dim. (T)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-26185 3.500 2.500 15.365 P 10.325

S-20800 3.625 0.312 1.986 P 1.334

S-20821 3.625 1.875 11.935 P 8.020

S-20795 3.750 2.625 17.286 P 11.615

S-4274 4.000 0.125 0.878 P P 0.590

S-2219 4.000 0.187 1.314 P P 0.883

S-2215 4.000 0.250 1.756 P P 1.180

S-2217 4.000 0.375 2.634 P P 1.770

S-2171 4.000 0.500 3.512 P P 2.360

S-21375 4.000 0.625 4.390 P P 2.950

S-4653 4.000 0.750 5.268 P P 3.540

S-4657 4.000 1.000 7.068 P P 4.750

S-18708 4.000 1.250 8.780 P P 5.900

S-17122 4.000 1.500 10.536 P P 7.080

S-12195 4.000 2.000 14.050 P P 9.440

S-26186 4.000 2.500 17.500 P 11.800

S-17140 4.000 3.000 21.072 P 14.160

S-20302 4.250 0.188 1.402 P 0.942

S-12796 4.250 1.000 7.463 P 5.015

S-20804 4.250 2.250 16.792 P 11.284

S-11474 4.429 0.630 4.899 P 3.292

S-21680 4.500 0.125 0.987 P 0.664

S-6118 4.500 0.187 1.479 P P 0.994

S-22085 4.500 0.250 1.975 P 1.327

S-12912 4.500 3.000 23.706 P 15.930

S-8915 4.625 0.158 1.284 P 0.863

S-8916 4.625 0.187 1.519 P 1.021

S-16645 4.700 1.000 8.253 P 5.546

S-2311 4.750 0.250 2.086 P P 1.402

S-15823 5.000 0.125 1.097 P 0.737

S-3654 5.000 0.182 1.598 P 1.074

S-3655 5.000 0.220 1.931 P 1.298

S-3296 5.000 0.250 2.195 P P 1.475

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular BarsSquare Edges

http://www.extrudex.com

Dim. (T)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-16638 5.000 0.375 3.292 P P 2.212

S-4768 5.000 0.500 4.390 P P 2.950

S-21683 5.000 0.625 5.487 P 3.687

S-65 5.000 0.750 6.585 P 4.425

S-23758 5.000 0.750 6.585 P 4.425

S-12198 5.000 1.000 8.780 P P 5.900

S-25582 5.000 1.500 13.170 P P 8.850

S-13042 5.000 2.000 17.560 P 11.800

S-24766 5.000 2.500 21.950 P 14.750

S-17141 5.000 3.000 26.340 P 17.700

S-2504 5.040 0.750 6.636 P 4.460

S-21469 5.250 0.190 1.751 P 1.177

S-2755 5.375 0.250 2.360 P 1.586

S-20480 5.500 0.160 1.544 P 1.037

S-22339 5.500 0.188 1.816 P 1.220

S-20634 5.500 0.250 2.419 P P 1.622

S-13218 5.500 0.375 3.621 P 2.434

S-2757 5.875 0.250 2.579 P 1.733

S-2232 6.000 0.250 2.634 P P 1.770

S-4650 6.000 0.375 3.951 P P 2.655

S-4652 6.000 0.500 5.268 P P 3.540

S-4800 6.000 0.750 7.902 P P 5.310

S-4658 6.000 1.000 10.530 P P 7.080

S-17121 6.000 1.250 13.170 P P 8.850

S-13077 6.000 1.500 15.804 P P 10.620

S-17125 6.000 2.000 21.072 P 14.160

S-20819 6.000 2.250 23.706 P 15.930

S-26514 6.000 2.500 26.340 P 17.700

S-18276 6.000 3.000 31.608 P 21.240

S-2489 6.125 0.375 4.032 P 2.710

S-26687 6.250 0.500 5.487 P 3.687

S-17443 6.375 1.625 18.191 P 12.224

S-21682 6.500 1.000 11.414 P 7.670

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular BarsSquare Edges

http://www.extrudex.com

Dim. (T)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-5070 6.750 0.250 2.964 P P 1.992

S-125 6.750 0.500 5.926 P 3.982

S-24451 7.000 0.500 6.146 P 4.130

S-66 7.000 0.750 9.219 P 6.195

S-24205 7.000 1.000 12.292 P 8.260

S-20812 7.000 2.250 27.657 P 18.585

S-22245 7.250 0.500 6.365 P 4.277

S-18313 7.250 0.750 9.548 P 6.416

S-22732 7.375 0.375 4.856 P 3.263

S-9001 8.000 0.187 2.633 P 1.769

S-12196 8.000 0.250 3.510 P 2.360

S-15198 8.000 0.250 3.512 P 2.360

S-12569 8.000 0.375 5.268 P P 3.540

S-12197 8.000 0.500 7.020 P P 4.720

S-9604 8.000 0.750 10.536 P P 7.080

S-16129 8.000 0.875 12.292 P 8.260

S-5830 8.000 1.000 14.046 P P 9.439

S-17419 8.000 1.250 17.560 P 11.800

S-9350 8.000 1.625 22.828 P 15.340

S-20788 8.000 1.750 24.584 P 16.520

S-10560 8.000 1.875 26.340 P 17.700

S-10914 8.000 2.000 28.096 P 18.880

S-17579 8.250 0.250 3.621 P 2.434

S-26441 8.380 0.250 3.679 P 2.472

S-20282 8.500 0.188 2.805 P 1.885

S-21681 8.500 0.375 5.596 P 3.760

S-23684 8.500 0.500 7.463 P 5.015

S-10170 8.504 0.394 5.879 P 3.950

S-15994 8.750 0.157 2.420 P 1.626

S-13660 9.000 0.250 3.951 P 2.655

S-18312 9.000 0.750 11.853 P 7.965

S-20813 9.125 1.875 30.044 P 20.189

S-26922 9.500 0.750 12.511 P 8.407

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular BarsSquare Edges

http://www.extrudex.com

Dim. (T)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-15448 10.000 0.250 4.390 P P 2.950

S-17932 10.000 0.375 6.585 P 4.425

S-23769 10.000 0.500 8.780 P P 5.900

S-22104 10.000 0.750 13.170 P P 8.850

S-16095 10.000 1.000 17.560 P P 11.800

S-20811 10.000 1.500 26.340 P 17.700

S-8792 12.000 0.250 5.268 P P 3.540

S-12570 12.000 0.375 7.902 P 5.310

S-23980 12.000 0.500 10.536 P P 7.080

S-20799 12.000 0.625 13.170 P 8.850

S-20792 12.500 0.250 5.487 P 3.687

S-18410 13.000 1.625 37.096 P 24.927

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular BarsFull Round Edges

http://www.extrudex.com

Dim. (T)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-4276 0.703 0.312 0.348 0.234 PS-4922 0.750 0.125 0.165 0.111 PPS-21963 0.750 0.188 0.234 0.157 PS-21964 0.750 0.250 0.306 0.205 PS-2299 1.000 0.250 0.417 0.280 PS-23745 1.125 0.125 0.241 0.162 PS-24936 1.250 0.375 0.770 0.518 PS-2250 1.375 0.375 0.851 0.572 PS-13825 1.500 0.125 0.323 0.217 PS-7348 1.500 0.156 0.402 0.270 PS-2174 1.500 0.250 0.635 0.427 PPS-13141 1.500 0.500 1.223 0.822 PS-13822 1.750 0.156 0.471 0.316 PS-2202 1.750 0.750 2.094 1.407 PS-2173 2.000 0.125 0.433 0.291 PS-13823 2.000 0.156 0.540 0.363 PPS-10077 2.000 0.188 0.646 0.434 PPS-2269 2.000 0.250 0.856 0.575 PPS-2266 2.000 0.375 1.265 0.850 PPS-15348 2.000 0.500 1.662 1.117 PS-14285 2.000 0.500 1.662 1.117 PS-13824 2.250 0.219 0.846 0.569 PS-26688 2.340 0.205 0.827 0.555 PS-2329 2.500 0.250 1.074 0.722 PS-2175 3.000 0.250 1.295 0.870 PS-2267 3.000 0.375 1.922 1.292 PS-5424 3.000 0.500 2.539 1.706 PS-9489 3.000 1.000 4.891 3.286 PS-2421 3.500 0.250 1.513 1.017 PS-2887 3.688 0.125 0.803 0.540 PS-2298 4.000 0.250 1.734 1.165 PPS-2248 4.000 0.375 2.582 1.735 PPS-5016 4.000 0.500 3.417 2.296 PP

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular BarsFull Round Edges

http://www.extrudex.com

Dim. (T)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-5423 4.000 1.000 6.646 4.466 PS-13987 4.500 0.375 2.910 1.956 PS-2302 5.000 0.250 2.172 1.460 PPS-2341 5.000 0.375 3.239 2.177 PS-27107 5.000 0.500 4.269 2.887 PS-2172 6.000 0.250 2.611 1.755 PS-2268 6.000 0.375 3.899 2.620 PS-5419 6.000 0.500 5.173 3.476 PPS-22055 6.000 0.750 7.690 5.168 PS-5422 6.000 1.000 10.150 6.826 PS-13669 6.500 0.500 5.613 3.772 PS-4952 7.000 0.250 3.050 2.050 PS-12466 7.000 0.500 6.052 4.067 PS-5420 8.000 0.375 5.215 3.505 PS-5421 8.000 0.500 6.929 4.656 PS-5693 8.000 1.000 13.669 9.186 PPS-5829 10.000 0.375 6.532 4.390 PS-6875 10.000 0.500 8.685 5.836 PP

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Square Bars

http://www.extrudex.com

Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-4528 0.295 0.153 P 0.103

S-12321 0.375 0.247 P P 0.166

S-2572 0.500 0.439 P P 0.295

S-2203 0.625 0.686 P P 0.461

S-2566 0.750 0.988 P P 0.664

S-2382 1.000 1.756 P P 1.180

S-4763 1.250 2.743 P P 1.843

S-14441 1.375 3.320 P 2.231

S-4661 1.500 3.951 P P 2.655

S-21815 1.625 4.637 P 3.116

S-14092 1.750 5.377 P P 3.614

S-3132 2.000 7.023 P P 4.720

S-4770 2.500 10.970 P P 7.375

S-4662 3.000 15.800 P P 10.620

S-24121 3.500 21.511 P 14.455

S-12408 4.000 28.096 P 18.880

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Round BarsRods

http://www.extrudex.com

Dim. (D)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-5706 0.312 0.134 P P 0.090

S-2333 0.375 0.193 à à 0.130

S-7766 0.438 0.265 P à 0.178

S-2162 0.500 0.344 P à 0.231

S-16303 0.562 0.436 P 0.293

S-3651 0.625 0.539 à à 0.362

S-21809 0.687 0.651 à 0.437

S-24767 0.687 0.651 P 0.437

S-4758 0.750 0.776 P à 0.522

S-2632 0.775 0.829 P 0.557

S-3652 0.812 0.909 P à 0.611

S-22032 0.840 0.973 P 0.654

S-4771 0.875 1.055 P 0.709

S-9515 0.875 1.055 à à 0.709

S-9514 0.938 1.212 P 0.814

S-6980 0.995 1.366 à 0.918

S-2845 1.000 1.378 P 0.926

S-9599 1.000 1.378 à à 0.926

S-12193 1.062 1.556 à 1.045

S-4772 1.125 1.745 P à 1.173

S-13376 1.125 1.745 à 1.173

S-8958 1.188 1.946 P 1.307

S-2187 1.250 2.155 à à 1.448

S-17999 1.313 2.378 P 1.598

S-4759 1.375 2.606 à à 1.751

S-26465 1.385 2.646 P 1.778

S-29039 1.438 2.852 P 1.916

S-3653 1.460 2.939 P 1.975

S-2500 1.500 3.102 P à 2.085

S-11049 1.562 3.365 à à 2.261

S-6851 1.625 3.642 P à 2.447

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Round BarsRods

http://www.extrudex.com

Dim. (D)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-26466 1.725 4.104 P 2.758

S-4760 1.750 4.223 à à 2.838

S-12194 1.812 4.528 à à 3.043

S-4761 1.875 4.848 P à 3.258

S-4663 2.000 5.518 à à 3.708

S-9257 2.125 6.229 P à 4.185

S-4762 2.250 6.982 à à 4.692

S-26904 2.375 7.779 à 5.228

S-26467 2.425 8.110 P 5.450

S-26750 2.438 8.198 à 5.509

S-4856 2.500 8.620 à à 5.793

S-21376 2.625 9.503 P 6.386

S-4664 2.750 10.430 à à 7.008

S-11048 2.875 11.400 à 7.660

S-4665 3.000 12.410 P à 8.341

S-12344 3.063 12.935 à 8.692

S-12505 3.125 13.469 à 9.050

S-4666 3.250 14.580 P à 9.789

S-6874 3.500 16.895 à à 11.353

S-13826 3.625 18.123 P 12.178

S-11050 3.750 19.395 à à 13.033

S-8748 3.875 20.709 P 13.916

S-6852 4.000 22.066 à 14.828

S-6860 4.250 24.910 à 16.739

S-4873 4.500 27.930 P 18.780

S-21378 4.750 31.118 P 20.910

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Hexagonal Bar

http://www.extrudex.com

Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-12511 0.625 0.593 P 0.399

S-13002 0.750 0.855 P P 0.575

S-13003 0.875 1.164 P 0.782

S-2364 1.125 1.924 P 1.293

S-6529 1.750 4.657 P 3.129

S-24770 3.000 13.687 P 9.197

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Tee BarsArchitectural

http://www.extrudex.com

Dim. (T)Dim. (P)Dim. (H)Dim. (B)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)S-9158 1.000 2.000 0.063 0.063 0.323 P 0.217S-8568 1.000 2.000 0.118 0.118 0.597 P 0.401S-4465 1.250 1.250 0.100 0.100 0.421 P 0.283S-3317 1.250 1.250 0.187 0.187 0.760 P 0.511S-6873 2.000 2.000 0.125 0.125 0.850 P P 0.571S-4574 2.000 2.000 0.187 0.187 1.252 P P 0.841S-22527 2.000 2.000 0.250 0.250 1.646 P 1.106S-29327 2.500 2.000 0.190 0.190 1.438 P 0.966S-29326 3.000 3.000 0.188 0.188 1.918 P 1.289

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Tee BarsStructural

http://www.extrudex.com

Dim. (R)Dim. (T)Dim. (P)Dim. (H)Dim. (B)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-6871 0.625 1.312 0.080 0.080 0.031 0.262 0.176 PS-3303 1.250 1.250 0.187 0.187 0.187 0.787 0.529 PS-2291 1.500 1.500 0.187 0.187 0.187 0.949 0.638 PS-2823 2.000 1.500 0.187 0.187 0.187 1.132 0.761 PS-2292 2.000 2.000 0.250 0.250 0.250 1.693 1.138 PS-7903 2.000 2.100 0.120 0.120 0.120 0.848 0.570 PS-4649 3.000 3.000 0.375 0.375 0.375 3.811 2.561 PPS-2846 4.000 1.625 0.125 0.125 0.125 1.213 0.815 PS-18614 4.000 4.000 0.375 0.375 0.375 5.126 3.445 PS-5335 4.000 5.000 0.500 0.500 0.500 7.651 5.141 PS-3272 5.000 3.000 0.375 0.375 0.312 5.128 3.446 PS-7737 5.000 3.000 0.375 0.375 0.375 5.126 3.444 P

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

http://www.extrudex.com

Angles, Equal LegsArchitectural

Dim (W) Dim (T) WT. (LBS/FT) WT. (KGS/MT) Toronto OhioDie Number

0.192 0.129 0.125 0.500S-3838 P 0.156 0.105 0.062 0.750S-3488 P 0.188 0.260 0.075 0.750S-25461 P 0.302 0.203 0.125 0.750S-2240 P P 0.508 0.342 0.177 0.906S-6095 P 0.211 0.142 0.062 1.000S-3804 P P 0.333 0.224 0.100 1.000S-4464 P 0.412 0.277 0.125 1.000S-2238 P P 0.595 0.400 0.187 1.000S-3316 P 0.945 0.635 0.240 1.240S-4473 P 0.397 0.267 0.094 1.250S-22341 P 0.521 0.350 0.125 1.250S-2416 P P 0.759 0.510 0.187 1.250S-15797 P P 0.319 0.215 0.062 1.500S-10940 P P 0.631 0.424 0.125 1.500S-2241 P P 0.924 0.621 0.187 1.500S-2103 P P 1.207 0.811 0.250 1.500S-13142 P 1.207 0.811 0.250 1.500S-15988 P 0.741 0.498 0.125 1.750S-2360 P 1.087 0.731 0.187 1.750S-2109 P P 1.427 0.959 0.250 1.750S-3821 P 0.850 0.571 0.125 2.000S-5129 P P 1.251 0.841 0.187 2.000S-2199 P P 1.646 1.106 0.250 2.000S-2456 P P 1.070 0.719 0.125 2.500S-3051 P P 1.580 1.062 0.187 2.500S-3615 P P 2.085 1.401 0.250 2.500S-15150 P P 1.289 0.866 0.125 3.000S-21456 P P 2.524 1.696 0.250 3.000S-15151 P P 3.704 2.489 0.375 3.000S-2418 P 4.829 3.245 0.500 3.000S-2123 P P 3.402 2.286 0.250 4.000S-27195 P

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Angles, Equal LegsStructural

http://www.extrudex.com

Dim. (R) OhioTorontoDie Number Dim. (W) Dim. (T) WT. (LBS/FT) WT. (KGS/MT)

0.104 0.062 0.500S-2197 P 0.062 0.070

0.247 0.125 0.625S-2200 P 0.062 0.166

0.308 0.125 0.750S-2239 P P 0.125 0.207

0.418 0.125 1.000S-2228 P P 0.125 0.281

0.609 0.187 1.000S-3302 P P 0.187 0.409

0.792 0.250 1.000S-3808 P P 0.250 0.532

0.527 0.125 1.250S-4773 P 0.125 0.354

0.772 0.187 1.250S-2321 P P 0.187 0.519

1.012 0.250 1.250S-2586 P 0.250 0.680

0.637 0.125 1.500S-2154 P P 0.125 0.428

0.937 0.187 1.500S-2108 P P 0.187 0.630

1.231 0.250 1.500S-2310 P P 0.250 0.827

1.451 0.250 1.750S-2318 P 0.250 0.975

0.857 0.125 2.000S-3819 P P 0.125 0.576

1.266 0.187 2.000S-2159 P P 0.187 0.851

1.670 0.250 2.000S-2158 P P 0.250 1.122

2.440 0.375 2.000S-2237 P P 0.375 1.640

1.594 0.187 2.500S-2151 P 0.187 1.071

2.108 0.250 2.500S-2414 P 0.250 1.417

3.009 0.375 2.500S-5128 P 0.375 2.083

1.922 0.187 3.000S-2236 P P 0.187 1.292

2.547 0.250 3.000S-2227 P P 0.250 1.712

3.756 0.375 3.000S-4667 P P 0.375 2.525

4.924 0.500 3.000S-4774 P 0.500 3.309

2.987 0.250 3.500S-24189 P 0.250 2.007

4.415 0.375 3.500S-27750 P 0.375 2.967

3.426 0.250 4.000S-22440 P 0.250 2.302

4.250 0.312 4.000S-4668 P 0.312 2.856

5.075 0.375 4.000S-4669 P P 0.375 3.410

6.679 0.500 4.000S-28192 P 0.500 4.488

7.708 0.375 6.000S-22741 P P 0.375 5.179

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Angles, Equal LegsStructural

http://www.extrudex.com

Dim. (R) OhioTorontoDie Number Dim. (W) Dim. (T) WT. (LBS/FT) WT. (KGS/MT)

10.191 0.500 6.000S-22758 P P 0.500 6.848

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Angles, Equal LegsAmerican Standard

http://www.extrudex.com

Dim. (R1)Dim. (R) OhioTorontoDie Number Dim. (W) Dim. (T) WT. (LBS/FT) WT. (KGS/MT)

0.301 0.202 0.125 0.750S-22328 P 0.125 0.094

0.411 0.276 0.125 1.000S-10520 P 0.125 0.094

0.597 0.401 0.188 1.000S-24693 P 0.125 0.094

0.767 0.516 0.250 1.000S-10521 P 0.125 0.094

0.523 0.351 0.125 1.250S-12 P 0.188 0.125

0.755 0.507 0.188 1.250S-24691 P 0.094 0.125

0.989 0.665 0.250 1.250S-13 P 0.188 0.125

0.633 0.425 0.125 1.500S-13546 P 0.188 0.125

0.930 0.625 0.188 1.500S-10522 P 0.188 0.125

1.209 0.812 0.250 1.500S-10523 P 0.188 0.125

1.428 0.960 0.250 1.750S-14 P 0.188 0.125

0.863 0.580 0.125 2.000S-10524 P 0.250 0.125

1.270 0.853 0.188 2.000S-10525 P 0.250 0.125

1.658 1.114 0.250 2.000S-10526 P 0.250 0.125

2.399 1.612 0.375 2.000S-15 P 0.250 0.125

1.600 1.075 0.188 2.500S-10527 P 0.250 0.125

2.097 1.409 0.250 2.500S-10528 P 0.250 0.125

3.057 2.054 0.375 2.500S-10529 P 0.250 0.125

1.917 1.288 0.188 3.000S-10530 P 0.312 0.250

2.501 1.680 0.250 3.000S-26326 P 0.250 0.250

2.514 1.689 0.250 3.000S-10531 P 0.312 0.250

3.693 2.482 0.375 3.000S-10532 P 0.312 0.250

4.818 3.238 0.500 3.000S-10533 P 0.312 0.250

2.969 1.995 0.250 3.500S-18 P 0.375 0.250

3.408 2.290 0.250 4.000S-10534 P 0.375 0.250

5.027 3.378 0.375 4.000S-10535 P 0.375 0.250

6.591 4.429 0.500 4.000S-18268 P 0.375 0.250

4.287 2.881 0.250 5.000S-21883 P 0.375 0.250

6.327 4.251 0.375 5.000S-10536 P 0.500 0.375

8.329 5.597 0.500 5.000S-24 P 0.500 0.375

7.644 5.136 0.375 6.000S-18492 P 0.500 0.375

12.469 8.379 0.625 6.000S-22733 P 0.500 0.380

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Angles, Unequal LegsArchitectural

http://www.extrudex.com

Dim. (H)Dim. (B)Die Number Dim. (T) OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-5502 0.625 0.062 0.500 0.116 P 0.078

S-12368 0.687 0.062 0.202 0.090 P 0.060

S-5784 0.750 0.120 0.375 0.212 P 0.143

S-2177 0.750 0.125 0.500 0.247 P 0.166

S-4261 0.950 0.125 0.810 0.359 P 0.241

S-24692 1.000 0.125 0.500 0.302 P 0.203

S-5597 1.000 0.065 0.625 0.177 P 0.119

S-2362 1.000 0.050 0.750 0.149 P 0.100

S-21967 1.000 0.062 0.750 0.183 P 0.123

S-6504 1.000 0.125 0.750 0.356 P P 0.240

S-3355 1.250 0.125 1.000 0.466 P P 0.313

S-4289 1.500 0.060 0.500 0.204 P 0.137

S-10065 1.500 0.125 0.625 0.439 P 0.295

S-2438 1.500 0.095 0.750 0.360 P 0.242

S-2243 1.500 0.125 0.750 0.467 P P 0.314

S-2751 1.500 0.055 1.000 0.235 P P 0.158

S-8136 1.500 0.063 1.000 0.269 P 0.181

S-2284 1.500 0.125 1.000 0.521 P P 0.350

S-25567 1.500 0.188 1.000 0.763 P 0.513

S-6641 1.625 0.188 0.750 0.722 P 0.485

S-2639 1.750 0.062 1.500 0.348 P 0.234

S-2206 1.875 0.125 1.125 0.631 P 0.424

S-5365 2.000 0.187 0.750 0.841 P 0.565

S-2954 2.000 0.055 1.000 0.284 P 0.191

S-9157 2.000 0.063 1.000 0.323 P P 0.217

S-17463 2.000 0.090 1.000 0.460 P P 0.309

S-8569 2.000 0.118 1.000 0.597 P 0.401

S-2397 2.000 0.125 1.000 0.631 P P 0.424

S-24876 2.000 0.188 1.000 0.928 P 0.624

S-3854 2.000 0.055 1.250 0.310 P 0.208

S-2205 2.000 0.125 1.250 0.686 P 0.461

S-2286 2.000 0.125 1.500 0.741 P P 0.498

S-2242 2.000 0.187 1.500 1.089 P P 0.732

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Angles, Unequal LegsArchitectural

http://www.extrudex.com

Dim. (H)Dim. (B)Die Number Dim. (T) OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-11637 2.250 0.125 2.000 0.905 P 0.608

S-16648 2.500 0.125 1.000 0.741 P P 0.498

S-25178 2.500 0.125 1.250 0.795 P 0.534

S-2955 2.500 0.055 1.500 0.381 P 0.256

S-2423 2.500 0.125 1.500 0.850 P P 0.571

S-15021 2.500 0.188 1.500 1.258 P 0.845

S-16652 2.500 0.188 1.750 1.341 P 0.901

S-22265 3.000 0.125 0.750 0.795 P 0.534

S-8274 3.000 0.063 1.000 0.435 P 0.293

S-13664 3.000 0.125 1.000 0.850 P P 0.571

S-26689 3.000 0.250 1.500 1.865 P 1.253

S-13808 3.000 0.125 2.000 1.070 P P 0.719

S-2244 3.000 0.187 2.000 1.582 P 1.063

S-17185 3.000 0.250 2.000 2.085 P 1.401

S-26845 3.000 0.375 2.000 3.045 P 2.046

S-20810 3.125 0.188 1.875 1.588 P 1.067

S-9560 3.500 0.188 2.500 1.918 P 1.289

S-5880 4.000 0.125 1.000 1.069 P 0.719

S-5881 6.000 0.125 1.000 1.508 P 1.014

S-28082 6.000 0.375 4.000 6.338 P 4.259

S-26690 6.250 0.312 5.000 5.992 P 4.027

S-24215 8.000 0.250 4.000 5.158 P 3.466

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Angles, Unequal LegsStructural

http://www.extrudex.com

Dim. (R)Dim. (H)Dim. (B) OhioTorontoDie Number Dim. (T) WT. (LBS/FT) WT. (KGS/MT)

0.472 0.317S-2178 P 1.250 0.125 1.000 0.125

0.472 0.317S-3805 P 1.500 0.125 0.750 0.125

0.527 0.354S-9935 P 1.500 0.125 1.000 0.125

0.772 0.519S-2160 P 1.500 0.187 1.000 0.187

0.385 0.258S-9567 P 1.750 0.090 0.750 0.094

0.439 0.295S-7913 P 1.750 0.094 1.000 0.094

0.385 0.258S-8592 P 1.750 0.070 1.125 0.094

1.018 0.684S-2320 P 2.000 0.187 1.250 0.187

1.101 0.740S-2153 P P 2.000 0.187 1.500 0.187

1.450 0.975S-4854 P P 2.000 0.250 1.500 0.250

1.266 0.851S-2152 P 2.500 0.187 1.500 0.187

1.670 1.122S-2275 P 2.500 0.250 1.500 0.250

0.966 0.649S-9934 P 2.500 0.125 2.000 0.125

1.429 0.960S-20805 P 2.500 0.187 2.000 0.187

1.889 1.270S-5361 P P 2.500 0.250 2.000 0.250

2.769 1.861S-4860 P 2.500 0.375 2.000 0.375

1.792 1.204S-17065 P 3.000 0.250 1.250 0.312

1.594 1.071S-2188 P 3.000 0.187 2.000 0.187

2.109 1.417S-3820 P P 3.000 0.250 2.000 0.250

3.098 2.082S-6858 P P 3.000 0.375 2.000 0.375

2.548 1.712S-4855 P 3.500 0.250 2.500 0.250

0.801 0.538S-11644 P 4.000 0.090 1.125 0.125

2.500 1.680S-17580 P P 4.000 0.250 2.000 0.250

2.986 2.007S-2306 P P 4.000 0.250 3.000 0.250

4.417 2.968S-4670 P P 4.000 0.375 3.000 0.375

5.801 3.898S-28426 P 4.000 0.500 3.000 0.500

4.248 2.855S-23642 P 5.000 0.312 3.000 0.312

5.074 3.409S-23242 P 5.000 0.375 3.000 0.375

5.403 3.631S-4861 P 5.000 0.375 3.500 0.375

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Angles, Unequal LegsStructural

http://www.extrudex.com

Dim. (R)Dim. (H)Dim. (B) OhioTorontoDie Number Dim. (T) WT. (LBS/FT) WT. (KGS/MT)

3.316 2.228S-6371 P 6.000 0.250 1.750 0.250

5.732 3.852S-17669 P 6.000 0.375 3.000 0.375

6.392 4.295S-4671 P P 6.000 0.375 4.000 0.375

8.436 5.669S-4672 P 6.000 0.500 4.000 0.500

3.404 2.287S-20614 P 8.000 0.197 2.000 0.187

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Angles, Unequal LegsAmerican Standard

http://www.extrudex.com

Dim. (R1)Dim. (R)Dim. (H)Dim. (B)Die Number Dim. (T) OhioTorontoWT. (LBS/FT) WT. (KGS/MT)S-15372 1.500 0.188 1.000 0.188 0.188 0.750 P 0.504S-10537 2.000 0.125 1.500 0.188 0.125 0.743 P 0.499S-10538 2.000 0.188 1.500 0.188 0.125 1.095 P 0.736S-28 2.000 0.250 1.500 0.188 0.125 1.428 P 0.960S-26692 2.500 0.188 1.500 0.188 0.188 1.245 P 0.837S-16470 2.500 0.188 1.500 0.250 0.125 1.270 P 0.853S-25197 2.500 0.250 1.500 0.250 0.125 1.658 P 1.114S-30 2.500 0.188 2.000 0.250 0.125 1.435 P 0.964S-10539 2.500 0.250 2.000 0.250 0.125 1.877 P 1.261S-11669 3.000 0.250 1.250 0.312 0.188 1.766 P 1.187S-10540 3.000 0.188 2.000 0.312 0.188 1.599 P 1.074S-10541 3.000 0.250 2.000 0.312 0.188 2.095 P 1.408S-10542 3.000 0.375 2.000 0.312 0.188 3.055 P 2.053S-31 3.000 0.250 2.500 0.313 0.250 2.295 P 1.542S-26693 3.500 0.250 1.500 0.250 0.125 2.097 P 1.409S-10543 3.500 0.250 2.500 0.312 0.250 2.514 P 1.689S-23127 4.000 0.375 2.500 0.375 0.250 4.039 P 2.714S-10544 4.000 0.250 3.000 0.375 0.250 2.969 P 1.995S-26327 4.000 0.312 3.000 0.312 0.250 3.654 P 2.455S-10545 4.000 0.375 3.000 0.375 0.250 4.368 P 2.935S-24929 5.000 0.250 3.000 0.375 0.250 3.408 P 2.290S-12660 5.000 0.375 3.000 0.438 0.313 5.019 P 3.373S-24115 6.000 0.375 3.500 0.375 0.375 5.956 P 4.002S-27277 6.000 0.375 4.000 0.500 0.375 6.327 P 4.251S-40 6.000 0.500 4.000 0.500 0.375 8.329 P 5.597S-25241 6.000 0.250 5.000 0.375 0.250 4.725 P 3.175

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

I-Beam and H-BeamAluminum Association

http://www.extrudex.com

Dim. (R)Dim. (T)Dim. (P)Dim. (H)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-6872 3.000 0.250 0.188 0.375 2.000 2.792 P 1.876S-20807 4.375 0.250 0.250 0.250 2.000 3.551 P 2.386S-26468 4.000 0.215 0.135 0.105 2.250 2.559 P 1.720S-23017 3.000 0.250 0.187 0.375 2.500 3.227 P 2.169S-23023 4.000 0.230 0.150 0.250 3.000 3.450 P 2.318S-27040 4.000 0.250 0.188 0.375 3.000 4.001 P 2.689S-2296 5.000 0.218 0.250 0.437 3.000 4.588 P 3.083S-3859 6.000 0.375 0.250 0.438 3.500 7.202 P 4.840S-26738 4.000 0.250 0.375 0.437 4.000 5.723 P 3.846S-5258 4.000 0.312 0.250 0.437 4.000 6.153 P P 4.135S-57 6.000 0.279 0.230 0.250 4.000 6.211 P 4.174S-20791 6.000 0.375 0.281 0.437 4.000 8.146 P 5.474S-24405 7.000 0.380 0.230 0.300 4.500 8.661 P 5.820S-20801 5.000 0.313 0.313 0.438 5.000 8.177 P P 5.494S-4403 5.000 0.375 0.312 0.562 5.000 9.389 P P 6.309S-21927 8.000 0.410 0.250 0.300 5.000 10.487 P 7.047S-27029 8.000 0.500 0.311 0.563 5.000 13.081 P 8.790S-26325 8.000 0.308 0.230 0.320 5.250 8.815 P 5.923S-58 6.000 0.269 0.240 0.250 6.000 8.064 P 5.419S-5411 6.000 0.375 0.312 0.625 6.000 11.366 P 7.638S-24769 6.000 0.500 0.375 0.375 6.000 14.040 P 9.435S-4851 5.500 0.312 0.250 0.312 7.250 10.232 P 6.876S-17391 8.000 0.433 0.288 0.400 8.000 16.014 P 10.761S-20745 8.000 0.500 0.375 0.750 8.000 19.505 P 13.107

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

I-Beam and H-BeamAmerican Standard

http://www.extrudex.com

Dim. (R1)Dim. (R)Dim. (P)Dim. (T)Dim. (W)Dim. (H) OhioTorontoWT.

(LBS/FT)

WT.

(KGS/MT)

Die Number

3.878 2.606S-13562 P 2.510 0.170 0.349 0.270 3.000 0.090

3.949 2.654S-55 P 2.660 0.190 0.190 0.290 4.000 0.110

5.122 3.442S-56 P 3.000 0.210 0.210 0.310 5.000 0.210

7.598 5.106S-16375 P 3.449 0.230 0.343 0.330 6.000 0.140

7.104 4.774S-63 P 4.000 0.290 0.313 0.313 4.000 0.145

11.730 7.882S-64 P 5.938 0.360 0.250 0.313 6.000 0.180

13.667 9.184S-26340 P 6.125 0.347 0.438 0.313 6.000 0.180

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

ChannelsArchitectual

http://www.extrudex.com

Dim. (T)Dim. (P)Dim. (H)Dim. (B)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-3204 0.500 0.062 0.062 0.500 0.150 P 0.101

S-3206 0.625 0.062 0.062 0.500 0.177 P 0.119

S-3400 0.750 0.125 0.125 0.500 0.384 P P 0.258

S-2141 0.625 0.062 0.062 0.625 0.191 P 0.129

S-2207 0.750 0.062 0.062 0.625 0.217 P 0.146

S-5792 1.250 0.062 0.062 0.625 0.327 P 0.219

S-26694 1.110 0.110 0.110 0.730 0.527 P 0.354

S-2255 0.500 0.125 0.125 0.750 0.330 P 0.222

S-7242 0.750 0.062 0.062 0.750 0.232 P 0.156

S-7577 0.750 0.125 0.125 0.750 0.439 P P 0.295

S-26695 1.375 0.125 0.125 0.750 0.713 P 0.479

S-2121 0.875 0.050 0.050 0.875 0.222 P 0.149

S-2138 0.500 0.125 0.125 1.000 0.384 P P 0.258

S-22112 0.750 0.065 0.065 1.000 0.270 P 0.182

S-9081 0.750 0.125 0.125 1.000 0.493 P 0.332

S-7243 1.000 0.125 0.125 1.000 0.604 P P 0.406

S-16346 2.000 0.125 0.125 1.000 1.042 P 0.700

S-19866 0.500 0.125 0.125 1.250 0.439 P 0.295

S-3326 0.625 0.125 0.125 1.250 0.494 P 0.332

S-26696 0.687 0.250 0.250 1.250 0.932 P 0.626

S-26697 0.781 0.250 0.375 1.250 1.015 P 0.682

S-4647 1.145 0.125 0.125 1.260 0.723 P 0.486

S-20926 1.000 0.048 0.048 1.360 0.284 P 0.191

S-7809 1.000 0.125 0.125 1.450 0.702 P 0.472

S-6855 0.500 0.125 0.125 1.500 0.493 P P 0.332

S-2703 0.625 0.093 0.093 1.500 0.418 P 0.281

S-8943 0.750 0.063 0.063 1.500 0.316 P 0.212

S-25206 0.750 0.125 0.125 1.500 0.603 P 0.405

S-7791 1.000 0.125 0.125 1.500 0.713 P P 0.479

S-7235 1.500 0.125 0.125 1.500 0.932 P 0.627

S-21823 1.500 0.250 0.250 1.500 1.756 P 1.180

S-22230 0.750 0.125 0.125 1.625 0.631 P 0.424

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

ChannelsArchitectual

http://www.extrudex.com

Dim. (T)Dim. (P)Dim. (H)Dim. (B)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-3521 1.330 0.080 0.080 1.688 0.588 P 0.395

S-15193 1.625 0.125 0.125 1.750 1.042 P 0.700

S-2122 0.875 0.050 0.050 1.875 0.309 P 0.208

S-9530 1.000 0.062 0.062 2.000 0.421 P 0.283

S-3356 1.000 0.125 0.125 2.000 0.823 P P 0.553

S-28963 1.000 0.188 0.188 2.000 1.196 P 0.804

S-70 2.000 0.250 0.250 2.000 2.414 P 1.622

S-21966 1.000 0.125 0.125 2.500 0.932 P 0.627

S-2440 1.312 0.188 0.188 2.500 1.568 P 1.054

S-4254 1.500 0.125 0.125 2.500 1.152 P P 0.774

S-16431 1.500 0.188 0.188 2.500 1.691 P 1.136

S-26921 2.000 0.250 0.375 2.500 3.073 P 2.065

S-27948 4.000 0.125 0.250 2.938 2.936 P 1.973

S-27937 0.500 0.125 0.125 3.000 0.823 P 0.553

S-4260 0.750 0.125 0.125 3.000 0.933 P 0.627

S-2752 1.000 0.125 0.125 3.000 1.043 P P 0.701

S-3512 1.500 0.125 0.125 3.000 1.262 P 0.848

S-9709 1.500 0.187 0.187 3.000 1.847 P P 1.241

S-4503 1.250 0.187 0.187 3.750 1.930 P 1.297

S-26698 0.969 0.125 0.125 4.000 1.248 P 0.839

S-3138 1.000 0.100 0.100 4.000 1.018 P P 0.684

S-26437 1.650 0.250 0.180 4.000 2.554 P 1.716

S-4619 0.500 0.062 0.062 4.200 0.554 P 0.372

S-3399 4.500 0.125 0.125 4.500 2.908 P 1.954

S-22687 2.000 0.188 0.188 5.000 2.847 P 1.913

S-20924 2.000 0.250 0.250 5.000 3.731 P 2.507

S-22434 1.000 0.125 0.125 5.250 1.536 P 1.032

S-10169 1.969 0.197 0.197 5.906 3.266 P 2.194

S-26440 2.000 0.230 0.200 6.000 3.560 P 2.392

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

ChannelsStructural

http://www.extrudex.com

Die Number Dim. (B) Dim. (H) Dim. (P) Dim. (T) Dim. (R) OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-2330 0.562 0.062 0.060 0.062 0.500 0.164 0.110 PS-2798 1.250 0.125 0.125 0.125 1.250 0.780 0.524 PS-2139 0.500 0.125 0.125 0.062 1.500 0.497 0.334 PS-3446 1.475 0.125 0.125 0.125 1.725 0.984 0.661 PS-9933 1.000 0.125 0.125 0.125 2.000 0.834 0.561 PS-24927 1.250 0.250 0.188 0.130 2.000 1.605 1.078 PS-6853 1.500 0.125 0.125 0.125 2.000 1.054 0.708 PS-4675 2.000 0.125 0.125 0.125 2.000 1.272 0.855 PS-25095 1.000 0.125 0.125 0.125 2.250 0.889 0.598 PS-4645 1.000 0.188 0.188 0.188 2.250 1.305 0.877 PS-8648 1.500 0.188 0.188 0.188 2.250 1.635 1.099 PS-3920 1.500 0.125 0.125 0.125 3.000 1.274 0.856 PS-51 1.500 0.200 0.130 0.250 3.000 1.694 1.138 PS-2247 1.500 0.250 0.187 0.312 3.000 2.211 1.486 PS-2246 1.500 0.312 0.250 0.312 3.000 2.760 1.855 PS-23764 1.500 0.375 0.375 0.375 3.000 3.563 2.394 PS-24928 1.750 0.260 0.170 0.250 3.000 2.385 1.603 PS-22095 2.000 0.250 0.250 0.250 3.000 2.900 1.949 PPS-2245 2.000 0.312 0.250 0.187 3.000 3.260 2.191 PS-23757 1.500 0.250 0.250 0.250 4.000 2.900 1.949 PS-4646 1.750 0.250 0.250 0.250 4.000 3.121 2.097 PS-12537 1.812 0.250 0.188 0.312 4.000 2.818 1.894 PS-25972 2.000 0.230 0.150 0.250 4.000 2.595 1.743 PS-2107 2.000 0.250 0.187 0.375 4.000 3.012 2.024 PS-22502 2.000 0.250 0.250 0.188 4.000 3.319 2.230 PS-4862 2.000 0.250 0.250 0.250 4.000 3.339 2.244 PPS-2328 2.000 0.312 0.250 0.375 4.000 3.778 2.539 PS-16347 2.250 0.290 0.190 0.250 4.000 3.479 2.338 PS-2312 2.500 0.312 0.250 0.187 4.000 4.247 2.854 PS-4435 2.000 0.312 0.187 0.375 5.000 3.734 2.509 PS-24768 2.000 0.343 0.281 0.375 5.000 4.644 3.120 PS-52 2.250 0.260 0.150 0.300 5.000 3.302 2.219 PS-4399 2.500 0.312 0.218 0.437 5.000 4.559 3.063 P

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

ChannelsStructural

http://www.extrudex.com

Die Number Dim. (B) Dim. (H) Dim. (P) Dim. (T) Dim. (R) OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-20594 2.500 0.375 0.250 0.437 5.000 5.302 3.563 PS-53 2.750 0.320 0.190 0.300 5.000 4.613 3.100 PS-22894 1.500 0.187 0.125 0.125 5.800 2.188 1.470 PS-24926 1.250 0.200 0.200 0.190 6.000 2.871 1.930 PS-4400 2.000 0.375 0.281 0.437 6.000 5.368 3.607 PS-26879 2.500 0.290 0.170 0.300 6.000 4.232 2.834 PS-4968 2.500 0.312 0.250 0.437 6.000 5.243 3.523 PPS-6966 2.500 0.437 0.375 0.437 6.000 7.356 4.943 PS-8605 2.750 0.375 0.250 0.437 6.000 6.071 4.079 PS-199 3.250 0.350 0.210 0.300 6.000 6.017 4.034 PS-6854 3.500 0.500 0.375 0.437 6.000 9.583 6.439 PS-26333 2.750 0.290 0.170 0.300 7.000 4.785 3.215 PS-2822 3.000 0.375 0.250 0.500 7.000 6.884 4.626 PS-26739 2.290 0.250 0.313 0.437 8.000 6.276 4.218 PS-18427 3.000 0.438 0.281 0.500 8.000 8.318 5.590 PS-22053 3.000 0.437 0.281 0.500 10.000 9.295 6.246 PS-18109 3.500 0.500 0.312 0.562 10.000 11.315 7.603 PS-18110 4.000 0.562 0.375 0.625 12.000 15.351 10.315 P

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

ChannelsAmerican Standard

http://www.extrudex.com

Dim. (R1)Dim. (R)Dim. (T)Dim. (P)Dim. (H)Dim. (B) OhioTorontoDie Number WT.

(LBS/FT)

WT.

(KGS/MT)

2.118 1.423S-10509 P 1.410 0.170 0.170 0.270 3.000 0.100

2.581 1.735S-10510 P 1.498 0.170 0.258 0.270 3.000 0.100

3.098 2.082S-10511 P 1.596 0.170 0.356 0.270 3.000 0.100

2.757 1.852S-10512 P 1.580 0.180 0.180 0.280 4.000 0.110

3.227 2.169S-10513 P 1.647 0.180 0.247 0.280 4.000 0.110

3.740 2.513S-10514 P P 1.720 0.180 0.320 0.280 4.000 0.110

3.458 2.324S-10515 P 1.750 0.190 0.190 0.290 5.000 0.110

4.643 3.120S-41 P 1.885 0.190 0.325 0.290 5.000 0.110

3.278 2.203S-24114 P 1.250 0.186 0.188 0.250 6.000 0.125

4.220 2.836S-43 P 1.920 0.200 0.200 0.300 6.000 0.120

4.483 3.013S-10516 P 1.945 0.200 0.225 0.300 6.000 0.120

5.421 3.643S-10517 P 2.034 0.200 0.314 0.300 6.000 0.120

6.717 4.514S-45 P 2.157 0.200 0.437 0.300 6.000 0.120

5.289 3.554S-10518 P 2.110 0.210 0.230 0.310 7.000 0.130

6.321 4.248S-26337 P 2.194 0.210 0.314 0.310 7.000 0.130

6.350 4.267S-47 P 2.290 0.220 0.250 0.320 8.000 0.130

7.883 5.297S-10519 P 2.600 0.240 0.240 0.340 10.000 0.140

10.737 7.215S-25630 P 2.960 0.280 0.300 0.380 12.000 0.170

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Square TubesSquare Corners

http://www.extrudex.com

Die Number Dim. (W) Dim. (T) OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-3855 0.500 0.050 0.158 P 0.106H-22243 0.625 0.050 0.202 P 0.136H-5140 0.750 0.050 0.246 P 0.165H-17510 0.750 0.062 0.299 P P 0.201H-6859 0.750 0.120 0.530 P P 0.356H-26849 0.750 0.125 0.549 P 0.369H-6869 0.995 0.125 0.764 P 0.513H-18984 1.000 0.062 0.408 P 0.274H-9376 1.000 0.090 0.576 P 0.387H-2439 1.000 0.095 0.604 P P 0.406H-4237 1.000 0.120 0.741 P P 0.498H-3325 1.250 0.120 0.952 P 0.640H-8195 1.250 0.125 0.987 P P 0.663H-6868 1.250 0.125 0.987 P 0.664H-2322 1.500 0.050 0.509 P 0.342H-23647 1.500 0.062 0.626 P 0.421H-18396 1.500 0.070 0.703 P 0.472H-9367 1.500 0.075 0.750 P 0.504H-23648 1.500 0.093 0.919 P 0.617H-7215 1.500 0.095 0.938 P 0.630H-2179 1.500 0.120 1.162 P P 0.781H-22212 1.500 0.188 1.732 P P 1.164H-25464 1.500 0.250 2.195 P 1.475H-20639 1.625 0.100 1.070 P 0.719H-17559 1.750 0.062 0.735 P 0.494H-25661 1.750 0.093 1.082 P 0.727H-7216 1.750 0.094 1.094 P 0.735H-2585 1.750 0.120 1.373 P P 0.923H-3154 1.775 0.085 1.008 P 0.678H-20641 2.000 0.060 0.817 P 0.549H-23646 2.000 0.093 1.246 P 0.837H-7217 2.000 0.095 1.271 P 0.854H-2270 2.000 0.120 1.583 P P 1.064

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Square TubesSquare Corners

http://www.extrudex.com

Die Number Dim. (W) Dim. (T) OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-22327 2.000 0.125 1.646 P 1.106H-18426 2.000 0.188 2.393 P P 1.608H-17072 2.000 0.250 3.073 P P 2.065H-8730 2.180 0.062 0.922 P 0.620H-20640 2.500 0.075 1.227 P 0.858H-7218 2.500 0.125 2.084 P P 1.401H-27087 2.500 0.188 3.053 P 2.051H-24875 2.500 0.250 3.951 P 2.655H-9847 2.625 0.125 2.193 P 1.474H-5200 3.000 0.125 2.523 P P 1.696H-24939 3.000 0.188 3.713 P P 2.495H-6856 3.000 0.250 4.829 P P 3.245H-3203 4.000 0.090 2.472 P 1.661H-20569 4.000 0.125 3.401 P P 2.286H-23960 4.000 0.187 5.008 P P 3.365H-15202 4.000 0.250 6.585 P P 4.425H-23024 4.000 0.375 9.548 P P 6.416H-22210 4.000 0.500 12.292 P 8.260H-13109 4.364 0.109 3.254 P 2.187H-7574 4.500 0.100 3.091 P 2.077H-7072 4.500 0.125 3.840 P 2.581H-15003 5.000 0.250 8.341 P 5.605H-20593 5.000 0.375 12.182 P P 8.186H-12287 5.830 0.109 4.380 P 2.943H-19501 6.000 0.125 5.158 P 3.466H-21586 6.000 0.188 7.675 P 5.157H-29399 8.000 0.188 10.316 P 6.932

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Square TubesRound Corners

http://www.extrudex.com

Die Number Dim. (W) Dim. (T) Dim. (R) Dim. (Q) OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-20638 0.750 0.050 0.045 0.010 0.243 P 0.163H-2433 0.750 0.064 0.093 0.029 0.296 P 0.199H-4466 0.750 0.100 0.093 0.000 0.445 P P 0.299H-20815 0.938 0.125 0.093 0.015 0.701 P 0.471H-5117 1.000 0.050 0.125 0.075 0.318 P 0.214H-6444 1.000 0.063 0.157 0.094 0.391 P P 0.263H-6846 1.000 0.064 0.156 0.092 0.397 P 0.267H-13656 1.000 0.065 0.125 0.060 0.409 P 0.275H-2137 1.000 0.075 0.156 0.081 0.460 P P 0.309H-20816 1.000 0.080 0.250 0.170 0.465 P 0.313H-22067 1.000 0.090 0.125 0.035 0.554 P 0.372H-9566 1.000 0.090 0.156 0.066 0.544 P P 0.366H-20796 1.000 0.100 0.093 0.015 0.619 P 0.416H-6026 1.000 0.100 0.156 0.056 0.601 P 0.404H-24083 1.000 0.120 0.120 0.120 0.742 P 0.498H-2669 1.000 0.120 0.156 0.036 0.708 P P 0.476H-22068 1.000 0.125 0.062 0.010 0.763 P 0.512H-13658 1.000 0.125 0.125 0.010 0.745 P 0.501H-11867 1.250 0.090 0.125 0.035 0.712 P 0.478H-20797 1.250 0.100 0.093 0.015 0.795 P 0.534H-10063 1.250 0.100 0.156 0.056 0.776 P P 0.522H-2442 1.250 0.120 0.156 0.036 0.918 P P 0.617H-21580 1.250 0.120 0.250 0.130 0.884 P 0.594H-10280 1.250 0.125 0.093 0.000 0.975 P 0.655H-8381 1.250 0.125 0.187 0.063 0.939 P 0.631H-25352 1.250 0.125 0.188 0.063 0.940 P 0.632H-9777 1.440 0.050 0.100 0.050 0.478 P 0.321H-6445 1.500 0.083 0.177 0.094 0.792 P 0.532H-20071 1.500 0.090 0.090 0.090 0.891 P 0.599H-9076 1.500 0.095 0.156 0.061 0.906 P 0.609H-20798 1.500 0.100 0.093 0.015 0.971 P 0.652H-3807 1.500 0.120 0.156 0.036 1.129 P P 0.759H-22496 1.500 0.120 0.312 0.192 1.072 P 0.720

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Square TubesRound Corners

http://www.extrudex.com

Die Number Dim. (W) Dim. (T) Dim. (R) Dim. (Q) OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-27163 1.500 0.120 0.370 0.250 1.051 P 0.706H-16350 1.500 0.125 0.312 0.192 1.116 P P 0.750H-19638 1.500 0.187 0.186 0.156 1.709 P P 1.149H-10357 1.550 0.125 0.125 0.080 1.238 P 0.832H-24930 1.688 0.125 0.188 0.188 1.372 P 0.922H-8712 1.700 0.135 0.225 0.090 1.421 P 0.955H-8126 1.700 0.188 0.188 0.037 1.923 P 1.292H-10073 1.820 0.120 0.280 0.160 1.354 P P 0.910H-20072 2.000 0.090 0.090 0.090 1.207 P P 0.811H-13894 2.000 0.100 0.100 0.000 1.319 P 0.886H-11634 2.000 0.102 0.383 0.281 1.258 P 0.845H-3839 2.000 0.120 0.255 0.135 1.513 P 1.017H-22497 2.000 0.120 0.375 0.255 1.471 P 0.988H-24938 2.000 0.125 0.125 0.000 1.623 P 1.091H-22294 2.000 0.125 0.125 0.125 1.646 P P 1.106H-13659 2.000 0.125 0.187 0.062 1.599 P 1.075H-6713 2.000 0.125 0.375 0.250 1.528 P P 1.027H-22129 2.000 0.187 0.250 0.250 2.381 P P 1.600H-24940 2.000 0.188 0.188 0.000 2.340 P P 1.572H-18310 2.000 0.188 0.281 0.093 2.287 P P 1.537H-29498 2.000 0.188 0.400 0.212 2.219 P 1.491H-24937 2.000 0.250 0.250 0.000 2.979 P 2.002H-27873 2.000 0.250 0.250 0.010 2.979 P 2.002H-11478 2.000 0.250 0.375 0.125 2.885 P P 1.938H-14696 2.375 0.160 0.375 0.215 2.347 P 1.577H-13791 2.500 0.100 0.100 0.000 1.671 P 1.123H-10074 2.500 0.120 0.280 0.160 1.926 P P 1.294H-28771 2.500 0.125 0.500 0.375 1.920 P 1.290H-25119 2.500 0.188 0.250 0.250 3.053 P 2.052H-29053 2.500 0.250 0.250 0.125 3.880 P 2.608H-13792 3.000 0.100 0.100 0.000 2.022 P 1.359H-23746 3.000 0.125 0.187 0.063 2.478 P 1.665H-6826 3.000 0.160 0.062 0.000 3.187 P 2.142

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Square TubesRound Corners

http://www.extrudex.com

Die Number Dim. (W) Dim. (T) Dim. (R) Dim. (Q) OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-14181 3.000 0.160 0.280 0.120 3.095 P 2.080H-13387 3.000 0.187 0.125 0.031 3.673 P 2.468H-23747 3.000 0.188 0.187 0.063 3.667 P 2.464H-13783 3.000 0.250 0.187 0.062 4.782 P P 3.213H-22173 3.000 0.250 0.438 0.188 4.593 P P 3.086H-22283 3.000 0.250 0.500 0.250 4.546 P 3.055H-3134 3.375 0.500 0.125 0.125 10.074 P 6.770H-10075 4.000 0.188 0.280 0.280 5.035 P P 3.383H-11781 4.000 0.250 0.500 0.250 6.302 P P 4.235H-13937 4.000 0.437 0.187 0.187 10.947 P 7.356H-15425 4.500 0.188 0.375 0.188 5.534 P 3.719H-26322 5.000 0.187 0.375 0.188 6.163 P 4.142H-27671 5.000 0.250 0.500 0.250 8.059 P 5.415H-20777 5.000 0.312 0.015 0.125 10.297 P 6.919

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular TubesSquare Corners

http://www.extrudex.com

Dim. (B) Dim. (T)Dim. (H)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-14871 0.500 0.050 0.750 0.200 P 0.134H-18259 0.500 0.062 0.750 0.245 P 0.165H-18514 0.500 0.125 1.000 0.549 P 0.369H-9369 0.750 0.065 1.000 0.369 P 0.248H-6821 0.520 0.065 1.015 0.321 P 0.216H-15634 0.750 0.125 1.500 0.878 P P 0.590H-26758 1.000 0.062 1.500 0.517 P 0.348H-5514 1.000 0.090 1.500 0.734 P P 0.493H-13784 1.000 0.125 1.500 0.988 P P 0.664H-7298 1.000 0.125 1.750 1.098 P 0.738H-3830 1.000 0.095 2.000 0.937 P P 0.630H-4960 1.000 0.125 2.000 1.208 P P 0.812H-23013 1.250 0.125 2.000 1.317 P 0.885H-2592 1.500 0.120 2.000 1.373 P 0.923H-16051 1.500 0.125 2.000 1.427 P 0.959H-15010 1.000 0.100 2.500 1.159 P 0.779H-2591 1.500 0.120 2.500 1.583 P P 1.064H-25118 2.000 0.250 2.500 3.512 P 2.360H-11036 0.750 0.080 3.000 1.008 P 0.678H-22492 1.000 0.120 3.000 1.584 P 1.065H-22330 1.000 0.125 3.000 1.646 P 1.106H-13665 1.500 0.125 3.000 1.866 P P 1.254H-16550 1.500 0.188 3.000 2.723 P P 1.830H-21882 1.750 0.094 3.000 1.506 P 1.012H-5261 2.000 0.120 3.000 2.005 P P 1.348H-18513 2.000 0.188 3.000 3.053 P P 2.051H-24170 2.000 0.250 3.000 3.951 P P 2.655H-26321 1.250 0.200 3.250 2.880 P 1.935H-5260 1.875 0.125 3.375 2.195 P 1.475H-26334 1.500 0.250 4.000 4.390 P 2.950H-3200 1.750 0.090 4.000 1.762 P P 1.184H-21468 1.750 0.190 4.000 3.583 P 2.408H-9368 2.000 0.120 4.000 2.427 P P 1.631

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular TubesSquare Corners

http://www.extrudex.com

Dim. (B) Dim. (T)Dim. (H)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-2249 2.000 0.187 4.000 3.695 P P 2.483H-16405 2.000 0.250 4.000 4.829 P P 3.245H-12575 2.000 0.375 4.000 6.855 P 4.606H-25447 3.000 0.188 4.000 4.373 P 2.939H-1070 3.000 0.250 4.000 5.707 P P 3.835H-15644 1.750 0.090 4.500 1.918 P 1.289H-10365 1.750 0.125 5.000 2.853 P 1.917H-21569 2.000 0.125 5.000 2.963 P P 1.991H-9550 2.500 0.188 5.000 4.704 P 3.161H-6636 2.992 0.093 5.000 2.549 P 1.713H-8751 4.000 0.125 5.000 3.841 P 2.581H-7567 1.750 0.100 6.000 2.652 P 1.782H-17430 2.000 0.120 6.000 3.270 P 2.198H-1318 2.000 0.125 6.000 3.402 P 2.286H-20019 2.000 0.188 6.000 5.034 P 3.382H-15283 2.000 0.250 6.000 6.585 P P 4.425H-13662 3.000 0.125 6.000 3.841 P 2.581H-1317 3.000 0.187 6.000 5.665 P 3.807H-15081 3.000 0.250 6.000 7.463 P 5.015H-27086 4.000 0.188 6.000 6.354 P 4.270H-13661 4.000 0.250 6.000 8.341 P P 5.605H-8744 3.500 0.250 6.250 8.121 P 5.457H-19567 3.000 0.250 8.000 9.219 P 6.195H-25679 4.000 0.250 8.000 10.097 P 6.785H-21471 6.000 0.250 8.000 11.853 P 7.965

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular TubesRound Corners

http://www.extrudex.com

Dim. (Q)Dim. (R)Dim. (T)Dim. (H)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-25349 0.500 0.125 0.125 1.000 0.063 0.531 P 0.357H-9808 0.750 0.100 0.156 1.000 0.056 0.512 P 0.344H-25351 0.750 0.125 0.188 1.000 0.063 0.611 P 0.411H-15239 1.000 0.062 0.125 1.500 0.063 0.500 P 0.336H-22160 1.000 0.120 0.250 1.500 0.125 0.882 P 0.593H-25350 1.000 0.125 0.188 1.500 0.063 0.940 P 0.632H-28769 1.000 0.188 0.250 1.500 0.250 1.399 P 0.940H-15240 1.000 0.062 0.125 2.000 0.063 0.609 P P 0.409H-27568 1.000 0.125 0.125 2.000 0.010 1.184 P 0.796H-14173 1.000 0.125 0.125 2.000 0.125 1.207 P 0.811H-8380 1.000 0.125 0.188 2.000 0.063 1.161 P P 0.780H-17138 1.000 0.125 0.250 2.000 0.125 1.137 P 0.764H-21585 1.250 0.090 0.060 2.000 0.010 0.965 P 0.649H-28768 1.500 0.125 0.250 2.000 0.250 1.427 P 0.959H-1183 1.000 0.125 0.250 2.500 0.125 1.356 P 0.911H-393 1.250 0.125 0.156 2.500 0.036 1.502 P 1.009H-11968 1.500 0.125 0.280 2.500 0.155 1.564 P P 1.051H-11026 1.000 0.120 0.182 3.000 0.062 1.541 P P 1.035H-20802 1.000 0.187 0.094 3.000 0.035 2.370 P 1.593H-24941 1.500 0.125 0.188 3.000 0.063 1.818 P 1.222H-17139 1.500 0.125 0.375 3.000 0.250 1.748 P 1.175H-11967 2.000 0.120 0.280 3.000 0.160 1.926 P 1.295H-15290 2.000 0.125 0.188 3.000 0.063 2.038 P P 1.369H-27874 2.000 0.250 0.188 3.000 0.016 3.898 P 2.619H-24842 2.000 0.250 0.250 3.000 0.125 3.880 P 2.608H-24942 1.625 0.187 0.187 3.625 0.000 3.150 P 2.117H-17949 1.000 0.125 0.125 4.000 0.010 2.062 P 1.386H-27570 1.125 0.090 0.070 4.000 0.125 1.579 P 1.061H-20701 1.250 0.125 0.250 4.000 0.120 2.123 P 1.426H-28611 2.000 0.120 0.250 4.000 0.130 2.359 P 1.585H-10076 2.000 0.120 0.280 4.000 0.280 2.429 P 1.632H-20862 2.000 0.125 0.125 4.000 0.010 2.501 P 1.681H-21813 2.000 0.125 0.188 4.000 0.063 2.477 P P 1.664

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Rectangular TubesRound Corners

http://www.extrudex.com

Dim. (Q)Dim. (R)Dim. (T)Dim. (H)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-23267 2.000 0.188 0.250 4.000 0.250 3.713 P 2.495H-20861 2.000 0.250 0.187 4.000 0.187 4.826 P 3.245H-27490 2.000 0.250 0.250 4.000 0.125 4.758 P 3.198H-17937 1.000 0.125 0.062 5.000 0.010 2.519 P 1.692H-14131 1.750 0.125 0.063 5.000 0.063 2.854 P 1.917H-13988 2.000 0.125 0.250 5.000 0.125 2.893 P P 1.944H-21486 2.000 0.250 0.250 5.000 0.125 5.636 P 3.788H-25948 2.500 0.125 0.188 5.000 0.063 3.136 P 2.107H-17298 3.000 0.250 0.250 5.000 0.250 6.585 P 4.425H-3293 4.250 0.250 0.625 5.000 0.038 7.307 P 4.910H-13989 2.000 0.125 0.250 6.000 0.125 3.332 P 2.239H-23748 2.000 0.188 0.187 6.000 0.010 4.981 P P 3.347H-21485 2.000 0.250 0.313 6.000 0.188 6.491 P 4.362H-16426 4.000 0.250 0.375 6.000 0.125 8.153 P 5.478H-20790 2.000 0.125 0.062 8.000 0.010 4.275 P P 2.872H-1080 2.000 0.250 0.187 8.000 0.062 8.294 P 5.573H-15316 2.500 0.250 0.187 8.000 0.062 8.732 P 5.868H-27076 4.000 0.188 0.500 8.000 0.312 7.445 P 5.003H-20817 4.000 0.250 0.031 8.000 0.016 10.010 P 6.727H-20789 3.360 0.180 0.500 10.360 0.320 8.223 P 5.526

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Round Tubes and Pipes

http://www.extrudex.com

RemarksDim. (D) Dim. (T)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-4421 0.073 0.311 0.097 P 0.065

H-9664 0.050 0.435 0.107 P 0.072

H-10299 0.059 0.472 0.134 P 0.090

H-14695 0.049 0.500 0.122 P 0.082

H-2575 0.065 0.500 0.156 P 0.105

H-4951 0.088 0.540 1/4" SCH. 40 PIPE 0.220 P 0.148

H-4921 0.049 0.625 0.156 P 0.105

H-22251 0.065 0.625 0.201 P 0.135

H-6847 0.091 0.675 3/8" SCH. 40 PIPE 0.293 P P 0.197

H-5141 0.050 0.750 0.193 P 0.129

H-22432 0.058 0.750 0.221 P 0.149

H-2576 0.065 0.750 0.246 P P 0.165

H-28964 0.120 0.750 0.417 P 0.280

H-2156 0.109 0.840 1/2" SCH. 40 PIPE 0.439 P P 0.295

H-7765 0.147 0.840 1/2" SCH. 80 PIPE 0.562 P P 0.378

H-3910 0.125 0.865 0.510 P 0.343

H-3692 0.062 0.875 0.277 P P 0.186

H-12790 0.049 1.000 0.257 P 0.173

H-2367 0.065 1.000 0.335 P P 0.225

H-20848 0.100 1.000 0.497 P P 0.334

H-3846 0.120 1.000 0.583 P P 0.392

H-12319 0.215 1.000 0.931 P 0.626

H-15148 0.250 1.000 1.034 P P 0.695

H-2157 0.113 1.050 3/4" SCH. 40 PIPE 0.585 P P 0.393

H-15282 0.154 1.050 3/4" SCH. 80 PIPE 0.761 P 0.512

H-20925 0.125 1.125 0.690 P 0.463

H-26176 0.156 1.125 0.834 P 0.560

H-21449 0.247 1.125 1.198 P 0.805

H-1342 0.100 1.185 0.599 P 0.402

H-4917 0.050 1.250 0.331 P P 0.222

H-2101 0.058 1.250 0.381 P 0.256

H-4838 0.065 1.250 0.425 P P 0.286

H-13580 0.085 1.250 0.546 P 0.367

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Round Tubes and Pipes

http://www.extrudex.com

RemarksDim. (D) Dim. (T)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-5157 0.095 1.250 0.606 P 0.407

H-2186 0.125 1.250 0.777 P P 0.522

H-22472 0.188 1.250 1.101 P 0.740

H-2637 0.250 1.250 1.378 P P 0.926

H-2304 0.327 1.250 1.665 P 1.119

H-12320 0.340 1.250 1.707 P 1.147

H-12123 0.409 1.250 1.898 P 1.275

H-2213 0.133 1.315 1" SCH. 40 PIPE 0.868 P P 0.583

H-3837 0.179 1.315 1" SCH. 80 PIPE 1.122 P P 0.754

H-5047 0.065 1.344 0.458 P 0.308

H-26516 0.125 1.375 0.862 P 0.579

H-23260 0.188 1.375 1.231 P 0.827

H-2794 0.125 1.425 0.897 P 0.603

H-2350 0.062 1.500 0.491 P P 0.330

H-13320 0.085 1.500 0.664 P 0.446

H-17285 0.085 1.500 0.664 P 0.446

H-2324 0.120 1.500 0.914 P P 0.614

H-22591 0.125 1.500 0.948 P 0.637

H-26469 0.157 1.500 1.160 P 0.779

H-27384 0.188 1.500 1.361 P 0.914

H-6861 0.250 1.500 1.724 P P 1.159

H-2424 0.453 1.500 2.616 P 1.758

H-5300 0.079 1.575 0.649 P 0.437

H-22043 0.437 1.625 2.860 P 1.926

H-15126 0.140 1.660 1.174 à 0.789

H-2214 0.140 1.660 1 1/4" SCH. 40 PIPE 1.174 P P 0.789

H-2503 0.191 1.660 1 1/4" SCH. 80 PIPE 1.548 P P 1.040

H-3089 0.268 1.660 2.055 P 1.381

H-6681 0.065 1.750 0.604 P P 0.406

H-20814 0.083 1.750 0.762 P 0.512

H-17286 0.095 1.750 0.867 P 0.583

H-23724 0.375 1.750 2.845 P 1.911

H-26177 0.300 1.795 2.474 P 1.663

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Round Tubes and Pipes

http://www.extrudex.com

RemarksDim. (D) Dim. (T)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-4881 0.125 1.839 1.183 P P 0.795

H-13503 0.065 1.875 0.649 P 0.436

H-9687 0.109 1.900 1 1/2" SCH. 10 PIPE 1.076 P P 0.723

H-2212 0.145 1.900 1 1/2" SCH. 40 PIPE 1.403 P P 0.943

H-2467 0.200 1.900 1 1/2" SCH. 80 PIPE 1.875 P P 1.260

H-2274 0.385 1.900 3.217 P 2.162

H-5301 0.079 1.969 0.821 P 0.551

H-4891 0.065 2.000 0.693 P P 0.466

H-3847 0.120 2.000 1.245 P P 0.837

H-21377 0.125 2.000 1.293 P P 0.869

H-16474 0.188 2.000 1.879 P P 1.263

H-11344 0.250 2.000 2.414 P P 1.622

H-18189 0.375 2.000 3.362 P 2.259

H-21750 0.128 2.016 1.333 P 0.896

H-16294 0.065 2.125 0.739 P 0.496

H-20781 0.120 2.125 1.327 P 0.892

H-20637 0.375 2.125 3.620 P 2.433

H-22338 0.125 2.250 1.465 P 0.985

H-8417 0.188 2.250 2.139 P 1.437

H-16551 0.250 2.250 2.758 P 1.854

H-26339 0.375 2.250 3.879 P 2.607

H-5302 0.157 2.362 1.915 P 1.287

H-2211 0.154 2.375 2" SCH. 40 PIPE 1.888 P P 1.269

H-2466 0.218 2.375 2" SCH. 80 PIPE 2.594 P P 1.743

H-9354 0.218 2.375 2" SCH. 80 PIPE 2.594 P 1.743

H-11962 0.065 2.500 0.873 P 0.587

H-13657 0.065 2.500 0.873 à 0.587

H-20869 0.120 2.500 1.576 P 1.059

H-21397 0.125 2.500 1.638 P 1.101

H-17269 0.250 2.500 3.103 P 2.085

H-26330 0.375 2.500 4.396 P 2.954

H-21558 0.500 2.500 5.517 P 3.707

H-10078 0.135 2.530 1.784 P 1.199

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Round Tubes and Pipes

http://www.extrudex.com

RemarksDim. (D) Dim. (T)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-19867 0.200 2.688 2.745 P 1.845

H-16081 0.250 2.750 3.449 P 2.317

H-2426 0.155 2.760 2.226 P 1.496

H-3273 0.203 2.875 2 1/2" SCH. 40 PIPE 2.992 P P 2.011

H-2201 0.276 2.875 2 1/2" SCH. 80 PIPE 3.957 P P 2.659

H-10376 0.050 2.980 0.808 P 0.543

H-5503 0.050 3.000 0.813 P 0.546

H-2577 0.065 3.000 1.052 P P 0.707

H-23259 0.083 3.000 1.336 P 0.898

H-19266 0.187 3.000 2.902 P 1.950

H-19620 0.250 3.000 3.793 P P 2.549

H-29334 0.500 3.000 6.896 P 4.634

H-20281 0.516 3.000 7.071 P 4.751

H-20159 0.750 3.000 9.309 P 6.256

H-3136 0.281 3.062 4.311 P 2.897

H-5298 0.157 3.150 2.599 P 1.747

H-20283 0.250 3.250 4.138 P P 2.780

H-26323 0.375 3.250 5.948 P 3.997

H-26338 0.500 3.250 7.585 P 5.097

H-8495 0.083 3.500 3" SCH. 5 PIPE 1.565 P 1.051

H-16298 0.120 3.500 3" SCH. 10 PIPE 2.238 P P 1.504

H-2210 0.216 3.500 3" SCH. 40 PIPE 3.912 P P 2.629

H-6857 0.300 3.500 3" SCH. 80 PIPE 5.296 P P 3.559

H-21356 0.375 3.500 6.465 P 4.344

H-21470 0.750 3.500 11.378 P 7.646

H-5299 0.197 3.543 3.634 P 2.442

H-23172 0.665 3.620 10.841 P 7.285

H-3135 0.344 3.750 6.464 P 4.344

H-891 0.500 3.750 8.965 P 6.024

H-16034 0.065 4.000 1.411 P P 0.948

H-16517 0.083 4.000 1.794 P 1.205

H-3806 0.125 4.000 2.672 P P 1.796

H-23068 0.188 4.000 3.954 P P 2.657

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Round Tubes and Pipes

http://www.extrudex.com

RemarksDim. (D) Dim. (T)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

H-3274 0.226 4.000 3 1/2" SCH. 40 PIPE 4.705 P P 3.162

H-11496 0.318 4.000 3 1/2" SCH. 80 PIPE 6.459 P P 4.341

H-26324 0.375 4.000 7.499 P 5.039

H-21379 0.500 4.000 9.654 P 6.487

H-23171 0.915 4.120 16.178 P 10.871

H-23670 0.375 4.125 7.758 P 5.213

H-20780 0.083 4.500 4" SCH. 5 PIPE 2.022 P 1.359

H-18705 0.120 4.500 4" SCH. 10 PIPE 2.900 P 1.948

H-19509 0.120 4.500 4" SCH. 10 PIPE 2.900 P 1.948

H-6281 0.237 4.500 4" SCH. 40 PIPE 5.574 P P 3.745

H-6282 0.337 4.500 4" SCH. 80 PIPE 7.739 P P 5.200

H-26757 0.531 4.500 4" SCH. 160 PIPE 11.627 P 7.813

H-6082 0.110 4.750 2.817 P 1.893

H-20779 0.083 5.000 2.251 P 1.513

H-23550 0.125 5.000 3.362 P 2.259

H-23595 0.156 5.000 4.169 P 2.801

H-23250 0.188 5.000 4.991 P 3.354

H-20332 0.245 5.000 4 1/2" SCH. 40 PIPE 6.427 P P 4.319

H-24621 0.437 5.000 11.001 P 7.392

H-17417 0.258 5.563 5" SCH. 40 PIPE 7.551 P P 5.074

H-20331 0.375 5.563 5" SCH. 80 PIPE 10.733 P P 7.212

H-430 0.120 6.000 3.893 P 2.616

H-23194 0.188 6.000 6.028 P 4.051

H-17229 0.250 6.000 7.930 P P 5.329

H-5063 0.104 6.625 6" SCH. 5 PIPE 3.742 P 2.514

H-6399 0.134 6.625 6" SCH. 10 PIPE 4.799 P 3.225

H-9036 0.280 6.625 6" SCH. 40 PIPE 9.802 P P 6.587

H-21962 0.432 6.625 6" SCH 80 PIPE 14.759 P P 9.918

H-25529 0.250 8.000 10.689 P 7.182

H-14304 0.281 8.000 11.987 P 8.055

H-16450 0.453 8.000 18.861 P 12.674

H-17180 0.322 8.625 8" SCH 40 PIPE 14.749 P 9.911

H-20787 0.200 10.750 11.640 P 7.822

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

Zees

http://www.extrudex.com

Dim. (R1)Dim. (R)Dim. (H) Dim. (T)Dim. (W)Die Number OhioTorontoWT. (LBS/FT) WT. (KGS/MT)

S-25196 1.750 0.188 1.750 0.188 0.125 1.624 P 1.091S-20927 1.000 0.062 2.000 0.010 0.015 0.422 P 0.283S-23027 1.250 0.188 2.375 0.188 0.125 1.500 P 1.008S-48 2.688 0.250 3.000 0.312 0.250 3.484 P 2.341S-25250 1.000 0.125 4.000 0.010 0.015 1.262 P 0.848S-49 3.063 0.250 4.000 0.312 0.250 4.252 P 2.857S-12272 3.188 0.375 4.125 0.375 0.250 6.480 P 4.354

(*) - 1/2 Commercial Tolerances Revised on: February 08, 2018

AA DESIGNATION SILICON IRON COPPER MANGANESE MAGNESIUM CHROMIUM ZINC TITANIUM ALUMINUM

EACH TOTAL MINIMUM

6005A 0.60-0.9 0.35 0.1 0.1 0.40-0.60 0.1 0.1 0.1 0.05 0.15 BALANCE

6061 0.4-0.8 0.7 0.15-0.4 0.15 0.80-1.20 0.04-0.35 0.25 0.15 0.05 0.15 BALANCE

6063 0.20-0.6 0.35 0.1 0.1 0.45-0.90 0.1 0.1 0.1 0.05 0.15 BALANCE

6351 0.70-1.3 0.5 0.1 0.40-0.8 0.40-0.80 0.2 0.2 0.05 0.15 BALANCE

ALLOY &TEMPER SPECIFIED AREA

DIAMETER OR (SQ. INCHES) (PERCENT

THICKNESS OR MINIMUM

MIN DISTANCE MIN. MAX. MIN. MAX. IN 2 INCHES)

ACROSS FLATS

(INCHES)

6005A

6005A-T1 UP THRU 0.249 ALL 25.0 14.5 15.0

6005A-T5 UP THRU 0.249 ALL 38.0 31.0 7.0

0.250 - 0.999 ALL 38.0 31.0 9.0

6005A-T61 UP THRU 0.249 ALL 38.0 35.0 8.0

0.250 - 1.000 ALL 38.0 35.0 10.0

6061

6061-T1 UP THRU 0.625 ALL 26.0 14.0 16.0

6061-T4 ALL ALL 26.0 16.0 16.0

6061-T6 UP THRU 0.249 ALL 38.0 35.0 8.0

AND T6511 0.250 AND OVER ALL 38.0 35.0 10.0

6063

6063-T1 UP THRU 0.500 ALL 17.0 9.0 12.0

0.501 - 1.000 ALL 16.0 8.0 12.0

6063-T4 UP THRU 0.500 ALL 19.0 10.0 14.0

0.501 - 1.000 ALL 18.0 9.0 14.0

6063-T5 UP THRU 0.500 ALL 22.0 16.0 8.0

0.501 - 1.000 ALL 21.0 15.0 8.0

6063-T52 UP THRU 1.000 ALL 22.0 30.0 16.0 25.0 8.0

6063-T6 UP THRU 0.124 ALL 30.0 25.0 8.0

0.125 - 1.000 ALL 30.0 25.0 10.0

6351

6351-T1 UP THRU 0.499 UP THRU 20 26.0 13.0 15.0

6351-T4 UP THRU 0.749 ALL 32.0 19.0 16.0

6351-T5 UP THRU 0.249 ALL 38.0 35.0 8.0

0.250-1.000 ALL 38.0 35.0 10.0

6351-T6 UP THRU 0.124 ALL 42.0 37.0 8.0

0.125 - 0.749 ALL 42.0 37.0 10.0

CHEMICAL COMPOSITION LIMITS

OTHERS

MECHANICAL PROPERTY LIMITS-EXTRUDED ROD, BAR AND PROFILES (SHAPES)

TENSILE STRENGTH - KSI

ULTIMATE YIELD

ELONGATION

wire, rod, bar and profilesCCCCextruded/standard tolerances

11-6 March, 2003

±10

% o

f spe

cifie

d di

men

sion

.060

max

. ±.0

10 m

in.

±15

% o

f spe

cifie

d di

men

sion

.090

max

. ±.0

15 m

in.

±15

% o

f spe

cifie

d di

men

sion

.090

max

. ±.0

25 m

in.

±15

% o

f spe

cifie

d di

men

sion

.090

max

. ±.0

15 m

in.

TABLE 11.2 Cross-Sectional Dimension TolerancesCCCCProfiles1EXCEPT FOR T3510, T4510, T6510, T73510, T76510 AND T8510 TEMPERS7

SPECIFIEDDIMENSION

in.

TOLERANCE23232323—in. plus and minus

METAL DIMENSIONS SPACE DIMENSIONS

ALLOWABLE DEVIATION FROMSPECIFIED DIMENSION WHERE

75 PERCENT OR MORE OFTHE DIMENSION IS METAL9bl9bl9bl9bl

ALLOWABLE DEVIATION FROM SPECIFIEDDIMENSION WHERE MORE THAN 25 PERCENT OF

THE DIMENSION IS SPACE68686868

AllExcept Those

Coveredby Column 3

Wall Thickness4444Completely5555

Enclosing Space0.11 sq. in. and

Over (Eccentricity)

AtDimensioned

Points0.250–0.624inches fromBase of Leg

AtDimensioned

Points0.625–1.249inches fromBase of Leg

AtDimensioned

Points1.250–2.499inches fromBase of Leg

AtDimensioned

Points2.500–3.999inches fromBase of Leg

AtDimensioned

Points4.000–5.999inches fromBase of Leg

AtDimensioned

Points6.000–8.000inches fromBase of Leg

Col. 1

Col. 2 Col. 3 Col. 4 Col. 5 Col. 6 Col. 7 Col. 8 Col. 9

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

CIRCUMSCRIBING CIRCLE SIZES LESS THAN 10 INCHES IN DIAMETER

Up thru 0.1240.125–0.2490.250–0.4990.500–0.7490.750–0.999

.009

.011

.012

.014

.015

.006

.007

.008

.009

.010

.013

.016

.018

.021

.023

.010

.012

.014

.016

.018

.015

.018

.020

.023

.025

.012

.014

.016

.018

.020

. ..020.022.025.027

. ..016.018.020.022

. .

. ..024.027.030

. .

. ..020.022.025

. .

. .

. .

. ..035

. .

. .

. .

. ..030

. .

. .

. .

. .

. .

. .

. .

. .

. .

. .

1.000–1.4991.500–1.9992.000–3.9994.000–5.9996.000–7.9998.000–9.999

.018

.021

.036

.051

.066

.081

.012

.014

.024

.034

.044

.054

.027

.031

.046

.061

.076

.091

.021

.024

.034

.044

.054

.064

.029

.033

.050

.067

.084

.101

.023

.026

.038

.050

.062

.074

.032

.038

.060

.081

.104

.127

.026

.031

.048

.064

.082

.100

.036

.043

.069

.095

.121

.147

.030

.036

.057

.078

.099

.120

.041

.049

.080

.111

.142

.182

.035

.042

.068

.094

.120

.145

. ..057.092.127.162.197

. ..050.080.110.140.170

CIRCUMSCRIBING CIRCLE SIZES 10 INCHES IN DIAMETER AND OVER

Up thru 0.1240.125–0.2490.250–0.4990.500–0.7490.750–0.999

.021

.022

.024

.025

.027

.014

.015

.016

.017

.018

.025

.026

.028

.030

.031

.018

.019

.020

.022

.023

.027

.029

.032

.035

.039

.020

.022

.024

.027

.030

. ..035.038.049.057

. ..028.030.040.050

. .

. ..058.068.079

. .

. ..050.060.070

. .

. .

. .

. ..099

. .

. .

. .

. ..090

. .

. .

. .

. .

. .

. .

. .

. .

. .

. .

1.000–1.4991.500–1.9992.000–3.9994.000–5.9996.000–7.999

.028

.036

.051

.066

.081

.019

.024

.034

.044

.054

.033

.046

.061

.076

.091

.024

.034

.044

.054

.064

.043

.056

.071

.086

.101

.034

.044

.054

.064

.074

.069

.082

.097

.112

.127

.060

.070

.080

.090

.100

.089

.102

.117

.132

.147

.080

.090

.100

.110

.120

.109

.122

.137

.152

.167

.100

.110

.120

.130

.140

. ..182.197.212.227

. ..170.180.190.200

8.000–9.99910.000–11.99912.000–13.99914.000–15.99916.000–17.999

.096

.111

.126

.141

.156

.064

.074

.084

.094

.104

.106

.121

.136

.151

.166

.074

.084

.094

.104

.114

.116

.131

.146

.161

.176

.084

.094

.104

.114

.124

.142

.157

.172

.187

.202

.110

.120

.130

.140

.150

.162

.177

.192

.207

.222

.130

.140

.150

.160

.170

.182

.197

.212

.227

.242

.150

.160

.170

.180

.190

.242

.257

.272

.287

.302

.210

.220

.230

.240

.250

18.000–19.99920.000–21.99922.000–24.000

.171

.186

.201

.114

.124

.134

.181

.196

.211

.124

.134

.144

.191

.206

.221

.134

.144

.154

.217

.232

.247

.160

.170

.180

.237

.252

.267

.180

.190

.200

.257

.272

.287

.200

.210

.220

.317

.332

.347

.260

.270

.280

1 These Standard Tolerances are applicable to the average profile; widertolerances may be required for some profiles and closer tolerances may bepossible for others.2 The tolerance applicable to a dimension composed of two or morecomponent dimensions is the sum of the tolerances of the componentdimensions if all of the component dimensions are indicated.3 When a dimension tolerance is specified other than as an equal bilateraltolerance, the value of the standard tolerance is that which applies to themean of the maximum and minimum dimensions permissible under thetolerance for the dimension under consideration.

4 Where dimensions specified are outside and inside, rather than wallthickness itself, the allowable deviation (eccentricity) given in Column 3applies to mean wall thickness. (Mean wall thickness is the average of twowall thickness measurements taken at opposite sides of the void.)5 In the case of Class 1 Hollow Profiles the standard wall thicknesstolerance for extruded round tube is applicable. (A Class 1 Hollow Profileis one whose void is round and one inch or more in diameter and whoseweight is equally distributed on opposite sides of two or more equallyspaced axes.)

(Continued on bottom of next page)

standard tolerances/wire, rod, bar and profilesCCCCextruded

11-7March, 2003

Examples Illustrating Use of Table 11.2, Page 11-6

Closed-Space Dimensions

All dimensions designated “Y” are classed as “metal dimensions,” and tolerances are determinedfrom column 2.Dimensions designated “X” are classed as “space dimensions through an enclosed void,” and thetolerances applicable are determined from column 4 unless 75 percent or more of the dimensionis metal, in which case column 2 applies.

Open-Space Dimensions

Tolerances applicable to dimensions “X” aredetermined as follows:

1. Locate dimension “X” in column 1.2. Determine which of columns 4–9 is

applicable, dependent on distance “A.”3. Locate proper tolerance in column 4, 5, 6,

7, 8 or 9 in the same line as dimension “X.”\Dimensions “Y” are “metal dimensions”; tolerances are determined from column 2.Distances “C” are shown merely to indicate incorrect values for determining which of columns4–9 apply.

Tolerances applicable to dimensions “X” are determined as follows:1. Locate distance “B” in column 1.2. Determine which of columns 4–9 is applicable, dependent on

distance “A.”3. Locate proper tolerance in column 4, 5, 6, 7, 8 or 9 in the same line

as value chosen in column 1.

Tolerances applicable to dimensions “X” are not determined from Table11.2; tolerances are determined by standard tolerances applicable toangles “A.”

Footnotes for page 11-7 (Continued)6 At points less than 0.250 inch from base of leg the tolerances in Col.2 are applicable.7 Tolerances for extruded profiles in T3510, T4510, T6510, T73510,T76510 and T8510 tempers shall be as agreed upon between purchaserand vendor at the time the contract or order is entered.8 The following tolerances apply where the space is completely en-closed (hollow profiles); For thewidth (A), the balance is the valueshown in Col. 4 for the depth di-mension (D). For the depth (D), thetolerance is the value shown inCol. 4 for the width dimension (A).In no case is the tolerance for ei-ther width or depth less than the metal dimensions (Col. 2) at the cor-ners.Example—Alloy 6061 hollow profile having 1 × 3 rectangular outside

dimensions; width tolerance is ±0.021 inch and depth tolerance±.034 inch. (Tolerances at corners, Col. 2, metal dimensions, are±0.024 inch for the width and ±0.012 inch for the depth.) Note thatthe Col. 4 tolerance of 0.021 inch must be adjusted to 0.024 inch sothat it is not less than the Col. 2 tolerance.

9 These tolerances do not apply tospace dimensions such as dimen-sions “X” and “Z” of the example(right), even when “Y” is 75 percentor more of “X.” For the toleranceapplicable to dimensions “X” and “Z,”use Col. 4, 5, 6, 7, 8 or 9, dependenton distance “A.”

bl The wall thickness tolerance for hol-low or semihollow profiles shall be asagreed upon between purchaser andvendor at the time the contract or orderis entered when the nominal thicknessof one wall is three times or greater thanthat of the opposite wall.bm Tolerances apply to 5xxx alloys with$4.0% nominal Mg.

wire, rod, bar and profilesCCCCextruded/standard tolerances

11-8 March, 2003

TABLE 11.3 Diameter or Distance Across FlatsCCCCRound Wire and Rod - Square, Hexagonaland Octagonal Wire and Bar

TOLERANCE3—in. plus and minus

ALLOWABLE DEVIATION FROM SPECIFIED DIMENSION ACROSS FLATS OR DIAMETER

SPECIFIEDDIMENSION

IN

ROUNDWIRE AND ROD

SQUAREWIRE AND BAR

HEXAGONALWIRE AND BAR

OCTAGONALWIRE AND BAR

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

5xxx$$$$4.0

nominalMgbmbmbmbm

OtherAlloys

Up thru 0.124 0.009 0.006 0.009 0.006 0.009 0.006 0.009 0.0060.125-0.249 0.011 0.007 0.011 0.007 0.011 0.007 0.011 0.0070.250-0.499 0.012 0.008 0.012 0.008 0.012 0.008 0.012 0.0080.500-0.749 0.014 0.009 0.014 0.009 0.014 0.009 0.014 0.0090.750-0.999 0.015 0.010 0.015 0.010 0.015 0.010 0.015 0.0101.000-1.499 0.018 0.012 0.018 0.012 0.018 0.012 0.018 0.0121.500-1.999 0.021 0.014 0.021 0.014 0.021 0.014 0.021 0.0142.000-3.999 0.036 0.024 0.036 0.024 0.036 0.024 0.036 0.0244.000-5.999 0.051 0.034 0.051 0.034 0.051 0.034 0.051 0.0346.000-7.070 0.066 0.044 0.066 0.044 0.066 0.044 0.066 0.0447.071-7.999 0.066 0.044 0.081 0.054 0.066 0.044 0.066 0.0448.000-8.659 0.081 0.054 0.096 0.064 0.081 0.054 0.081 0.0548.660-8.999 0.081 0.054 0.096 0.064 0.096 0.064 0.081 0.0549.000-9.238 0.081 0.054 0.096 0.064 0.096 0.064 0.081 0.0549.239-9.999 0.081 0.054 0.096 0.064 0.096 0.064 0.096 0.064

10.000-11.999 0.111 0.074 0.111 0.074 0.111 0.074 0.111 0.07412.000-13.999 0.126 0.084 0.126 0.084 0.126 0.084 0.126 0.08414.000-15.999 0.141 0.094 0.141 0.094 0.141 0.094 0.141 0.094

Note: Shaded tolerances denote products with a circumscribing circle size of 10 inches in diameter and over.

For all numbered footnotes, see pages 11-6 and 11-7.

TABLE 11.4 Thickness or Width (Distance Across Flats)CCCCRectangular Wire and Bar

TOLERANCE—in. plus and minus

ALLOWABLE DEVIATION FROM SPECIFIEDWIDTH OR THICKNESS ACROSS FLATS

SPECIFIEDDIMENSION

IN.

5xxx$$$$4.0

nominalMgbm

OtherAlloys

5xxx$$$$4.0

nominalMgbm

OtherAlloys

Up thru 0.1240.125-0.2490.250-0.4990.500-0.7490.750-0.9991.000-1.4991.500-1.9992.000-3.9994.000-5.9996.000-7.9998.000-9.999

10.000-11.99912.000-13.99914.000-15.99916.000-17.99918.000-19.99920.000-21.99922.000-24.000

0.0090.0110.0120.0140.0150.0180.0210.0360.0510.0660.081

. .

. .

. .

. .

. .

. .

. .

0.0060.0070.0080.0090.0100.0120.0140.0240.0340.0440.054

. .

. .

. .

. .

. .

. .

. .

0.0210.0220.0240.0250.0270.0280.0360.0510.0660.0810.0960.1110.1260.1410.1560.1710.1860.201

0.0140.0150.0160.0170.0180.0190.0240.0340.0440.0540.0640.0740.0840.0940.1040.1140.1240.134

Note: Shaded tolerances denote products with a circumscribing circle size of 10 inches in diameter and over.

For numbered footnote, see page 11-7.

standard tolerances/wire, rod, bar and profilesCCCCextruded

11-9March, 2003

TABLE 11.5 Length1CCCCWire, Rod, Bar and Profiles

SPECIFIED DIAMETER (WIRE AND ROD):SPECIFIED WIDTH (BAR):

CIRCUMSCRIBINGCIRCLE DIAMETER4444:

(PROFILES)in.

TOLERANCE—in. plus

ALLOWABLE DEVIATION FROM SPECIFIED LENGTH

SPECIFIED LENGTH—ft.

Upthru12

Over12

thru30

Over30

thru50

Over50

Up thru 2.9993.000–7.999

8.000 and over

1'83'161'4

1'45'163'8

3'87'161'2

111

TABLE 11.6 Straightness1 CCCCRod, Bar and Profiles

PRODUCT TEMPER

SPECIFIED DIAMETER(ROD):

SPECIFIED WIDTH(BAR):

CIRCUMSCRIBINGCIRCLE DIAMETER4444:

(PROFILES)

in.

SPECIFIEDTHICKNESS

(RECTANGLES):

MINIMUMTHICKNESS:(PROFILES)

in.

TOLERANCE3333—in.

ALLOWABLE DEVIATION (D) FROM STRAIGHT9999

IN TOTAL LENGTH OR IN ANYMEASURED

SEGMENT OF ONE FT.OR MORE OF TOTAL LENGTH

Rod and Square,Hexagonal

and OctagonalBar

All except OTX5102TX5112

All . . .0125 × Measured length, ft.

O 0.500 and over . . .050 × Measured length, ft.

TX5102 0.500 and over . . .050 × Measured length, ft.

TX5112 0.500 and over . . .0125 × Measured length, ft.

RectangularBar

All except OTX5102TX5112

Up thru 1.499 Up thru 0.09470.095 and over

.050 × Measured length, ft..0125 × Measured length, ft.

1.500 and over All .0125 × Measured length, ft.

O Over 0.500 0.500 and over .050 × Measured length, ft.

TX5102 Over 0.500 0.500 and over .050 × Measured length, ft.

TX5112 Over 0.500 0.500 and over .0125 × Measured length, ft.

Profiles

All except OTX51025TX5112

Up thru 1.499 Up thru 0.09470.095 and over

.050 × Measured length, ft..0125 × Measured length, ft.

1.500 and over All .0125 × Measured length, ft.

O 0.500 and over Up thru 0.09470.095 and over

.200 × Measured length, ft.

.050 × Measured length, ft.

TX5112 0.500 and over Up thru 0.09470.095 and over

.050 × Measured length, ft..0125 × Measured length, ft.

Footnotes for Pages 11-9 and 11-101 These Standard Tolerances are applicable to the average profile;wider tolerances may be required for some profiles, and closer toler-ances may be possible for others.2 TX510 and TX511 are general designations for the following stressrelieved tempers: T3510, T4510, T61510, T6510, T8510, T73510,T76510 and T3511, T4511, T61511, T6511, T8511, T73511, T76511,respectively.3 When weight of piece on the flat surface minimizes deviation.4 The circumscribing circle diameter is the diameter of the smallestcircle that will completely enclose the cross section of the extrudedproduct.5 Tolerances for T3510, T4510, T6510, T73510, T76510, and T8510tempers shall be as agreed upon between purchaser and vendor at thetime the contract or order is entered.

6 See Standards Section (6) for Application of Twist Limits; for addi-tional information, see Aluminum Association publication “UnderstandingAluminum Extrusion Tolerances”.7 Applies only if the thickness along at least 1'3 of the total perimeter is0.094 or less. Otherwise use the tolerance shown for 0.095 and over.8 Tolerance for “O” temper material is four times the standard toler-ances shown.9 Straightness must be met in all orientations, including orientationswhich are not self-supporting.

D

wire, rod, bar and profilesCCCCextruded/standard tolerances

11-10 March, 2003

TABLE 11.7 Twist16CCCCBar and Profiles

PRODUCT TEMPER

SPECIFIEDWIDTH(BAR):

CIRCUMSCRIBINGCIRCLE DIAMETER4444:

(PROFILES)

in.

SPECIFIEDTHICKNESS

(RECTANGLES):

MINIMUMTHICKNESS:(PROFILES)

in.

TOLERANCE3333—Degrees

ALLOWABLE DEVIATION FROM STRAIGHT

IN TOTAL LENGTH OR INANY MEASURED SEGMENT

OF ONE FT. OR MOREOF TOTAL LENGTH

MAXIMUMFOR TOTAL

LENGTH

Bar

All except OTX5102TX5112

Up thru 1.4991.500–2.9993.000 and over

AllAllAll

1 × Measured length, ft.½ × Measured length, ft.¼ × Measured length, ft.

753

O0.500–1.4991.500–2.9993.000 and over

0.500 and over0.500 and over0.500 and over

3 × Measured length, ft.1½ × Measured length, ft.

¾ × Measured length, ft.

21 15

9

TX5102 0.500–2.9993.000 and over

0.500 and over0.500 and over

1½ × Measured length, ft.½ × Measured length, ft.

75

TX51120.500–1.4991.500–2.9993.000 and over

0.500 and over0.500 and over0.500 and over

1 × Measured length, ft.½ × Measured length, ft.¼ × Measured length, ft.

753

Profiles

All except OTX51025TX5112

Up thru 1.4991.500–2.9993.000 and over

AllAllAll

1 × Measured length, ft.½ × Measured length, ft.¼ × Measured length, ft.

753

O0.500 and over0.500–1.4991.500–2.9993.000 and over

Up thru 0.094 70.095 and over0.095 and over0.095 and over

3 × Measured length, ft.3 × Measured length, ft.

1½ × Measured length, ft.¾ × Measured length, ft.

21 21 15

9

TX51120.500 and over0.500–1.4991.500–2.9993.000 and over

Up thru 0.094 70.095 and over0.095 and over0.095 and over

1 × Measured length, ft.1 × Measured length, ft.½ × Measured length, ft.¼ × Measured length, ft.

7753

TABLE 11.8 Flatness (Flat Surfaces)1CCCCBar, Solid Profiles and Semihollow Profiles EXCEPT FOR PROFILES IN O8, T3510, T4510, T6510, T73510, T76510 and T8510 TEMPERS5

SURFACES WIDTHS UP THRU 1 INCH OR ANY 1 INCH INCREMENT OFWIDER SURFACES

Maximum Allowable Deviation D = TOLERANCE (in.)

WIDTHS OVER 1 INCHMaximum Allowable Deviation D = TOLERANCE × W (in.)

MINIMUM THICKNESSOF METAL FORMING

THE SURFACEin.

SURFACE WIDTH—in.

UPTO

5.999

6.000TO

7.999

8.000TO

9.999

10.000TO

11.999

12.000TO

13.999

14.000TO

15.999

16.000TO

17.999

18.000TO

19.999

20.000TO

21.999

22.000TO

23.999

24.000ANDUP

TOLERANCE

Up thru 0.124 .004 .006 .010 .014 . . . . . . . . . . . . . .

0.125-0.187 .004 .006 .008 .012 .014 .014 .014 . . . . . . . .

0.188-0.249 .004 .006 .008 .010 .012 .012 .012 .014 .014 . . . .

0.250-0.374 .004 .006 .006 .008 .010 .010 .012 .012 .012 .014 . .

0.375-0.499 .004 .004 .006 .008 .008 .008 .010 .010 .010 .012 .014

0.500-0.749 .004 .004 .006 .006 .008 .008 .008 .008 .010 .010 .012

0.750-0.999 .004 .004 .006 .006 .008 .008 .008 .008 .008 .008 .010

1.000-1.499 .004 .004 .004 .006 .006 .008 .008 .008 .008 .008 .008

1.500-1.999 .004 .004 .004 .004 .006 .006 .006 .008 .008 .008 .008

2.000 and up .004 .004 .004 .004 .004 .006 .006 .006 .008 .008 .008

For all numbered footnotes, see page 11-9.

standard tolerances/wire, rod, bar and profilesCCCCextruded

11-11March, 2003

HOLLOW PROFILES EXCEPT FOR PROFILES IN Obl, T3510, T4510, T6510, T73510,T76510 and T8510 TEMPERS4TABLE 11.9 Flatness (Flat Surfaces)1

SURFACES WIDTHS UP THRU 1 INCH OR ANY 1 INCH INCREMENT OF WIDER SURFACES

Maximum Allowable Deviation D = TOLERANCE (in.)

WIDTHS OVER 1 INCH

Maximum Allowable Deviation D = TOLERANCE × W (in.)

MINIMUM THICKNESSOF METAL FORMING

THE SURFACEin.

SURFACE WIDTH—in.

UPTO

5.999

6.000TO

7.999

8.000TO

9.999

10.000TO

11.999

12.000TO

13.999

14.000TO

15.999

16.000TO

17.999

18.000TO

19.999

20.000TO

21.999

22.000TO

23.999

24.000ANDUP

TOLERANCE

Up thru 0.124 .006 .008 .012 .016 . . . . . . . . . . . . . .

0.125-0.187 .006 .008 .010 .014 .016 . . . . . . . . . . . .

0.188-0.249 .004 .006 .010 .012 .014 .014 .014 .016 . . . . . .

0.250-0.374 .004 .006 .008 .010 .012 .012 .012 .014 .014 .016 . .

0.375-0.499 .004 .006 .008 .010 .010 .010 .012 .012 .012 .014 .016

0.500-0.749 .004 .004 .006 .008 .008 .008 .010 .010 .012 .012 .014

0.750-0.999 .004 .004 .006 .006 .008 .008 .008 .008 .010 .010 .012

1.000 and up .004 .004 .004 .006 .006 .008 .008 .008 .008 .008 .008

TABLE 11.10 Surface Roughness18CCCCWireRod, Bar & Profiles

SPECIFIED SECTION THICKNESSin.

ALLOWABLE DEPTHOF CONDITIONS2222

in. max.

Up thru 0.0630.064-0.1250.126-0.1880.189-0.2500.251-0.5000.501- and over

.0015

.002

.0025

.003

.004

.008

TABLE 11.11 Contour (Curved Surfaces)13CCCCProfiles

Temper

All exceptO,

TX5104

Allowable deviation from specified contour: 0.005 inchper inch of chord length; 0.005 inch minimum. Not appli-cable to contours with chord length 6 inch and over.

OAllowable deviation from specified contour: 0.015 inchper inch of chord length; 0.015 inch minimum. Not appli-cable to contours with chord length 6 inches and over.

TABLE 11.12 Squareness of Cut Ends1Allowable deviation from square: 1 degree

TABLE 11.13 Corner and Fillet Radii1CCCCBar and Profiles

SPECIFIED RADIUS9999in.

TOLERANCE—in.

ALLOWABLE DEVIATIONFROM SPECIFIED RADIUS

Difference between radiusA and specified radius

Sharp corners0.016–0.187

0.188 and over

+1'64

±1'64

±10%

TABLE 11.14 Angularity15CCCCBar and Profiles

TEMPER

MINIMUMSPECIFIED

LEGTHICKNESS

in.

TOLERANCEDegrees plus and minus

ALLOWABLE DEVIATION FROMSPECIFIED ANGLE

RATIO:67676767LEG OR SURFACELENGTH TO LEG OR METAL

THICKNESS

1 and less Over 1 thru 40

Col. 1 Col.2 Col.3

All exceptO,

TX5104

Up thru 0.1870.188–0.749

0.750 and over

111

21½1

OUp thru 0.1870.188–0.749

0.750 and over

333

64½3

1 These Standard Tolerances are applicable to the average profile; widertolerances may be required for some profiles, and closer tolerances may bepossible for others.2 Conditions include die lines and handling marks.3 As measured with a contour gauge whose surface is limited to a maximum sub-tended angle of 90 degrees. Extruded curved surfaces comprising more than a 90-degree subtended angle are checked by sliding the gauge across the surface, thuschecking two or more 90-degree portions of the surface. Extruded profile surfacescomprising arcs formed by two or more radii require the use of a separate contourgauge for each portion of the surface formed by an individual radius.4 Tolerances for T3510, T4510, T6510, T73510, T76510 and T8510 tempersshall be as agreed upon between the purchaser and vendor and at the time thecontract or order is entered.5 Angles are measured with protractors or with gauges.As illustrated, a four-point contact system is used, twocontact points being as close to the angle vertex as prac-tical, and the others near the ends of the respectivesurfaces forming the angle. Between these points ofmeasurement surface flatness is the controlling tolerance.6 When the area between the surface forming an angle is all metal, values incolumn 2 apply if the larger surface length to metal thickness ratio is 1 or less.7 When two legs are involved the one having the larger ratio determines theapplicable column.8 Not applicable to 2219 alloy extrusions. Most profiles in 2219 alloy will havedie lines about twice the depth shown in the table; however, for each profile thesupplier should be contacted for the roughness value to apply.9 If unspecified, the radius shall be 1'32 in. maximum including tolerances.bl Tolerance for “O” temper material is four times the standard tolerances shown.


Recommended