Page 1 of 13 FBL-530 Lathe
FBL-530A Chevalier Slant Bed Lathes
Page 2 of 13 FBL-530 Lathe
CHEVALIER's FBL-530A slant bed lathes are stable, highly accurate machines that can handle
rough and fine turning operations for large work pieces.
Structure:
This machine is a 45° slant bed design made by one piece Meehanite cast iron with wide span ribbed
box structure. The four over size box ways are 130 mm in width and 80 mm in height provide strong
stability and support. They are heat treated to Rockwell 55 degree and stress relieved.
Capacity:
The spindle bore diameter is 196 mm (7.7") that suits most oil industry application. The maximum
swing diameter is 40.5" and cutting diameter is 37". The maximum cutting length is 118".
Power:
The powerful 60 HP Spindle motor with 4-stage gear headstock that generates up to 7,118 NM torque
would satisfy most cutting condition of large diameter work pieces or tough material application.
Turret:
The massive 200 mm thick disk and hydraulic clamping of curvic coupling design ensure cutting
stability during rough turning environment.
Accessories:
The standard equipment of programmable tailstock has a built-in MT-6 rotary quill. It has a better part's
weight support than normal live center type of quill.
Dual chuck easy access design provides convenience of loading and unloading longer part.
Best of all, this model comes with powerful FANUC Oi-TD control and digital servo drive and motor. Please see our demo video on You Tube. http://www.youtube.com/watch?v=N5W7yphU3kY
Page 3 of 13 FBL-530 Lathe
Machine Specifications:
Capacity Swing Over Bed: ..................................................................................................................................... 40.55” Swing Over Cross Slide .......................................................................................................................... 31.49” Maximum Turning Diameter: ....................................................................................................................... 37” Maximum Turning Length ......................................................................................................................... 118.11” Distance between Centers ....................................................................................................................... 118.11”
Headstock Spindle Nose .............................................................................................................................................. A2-15 Through Spindle Hole Diameter ............................................................................................................... 7.7” (A) Spindle Speeds ...................................................................................................................................... 1000 rpm Spindle Motor .............................................................................................................................................. 60 HP Transmission ................................................................................................................ 4-speed Gear headstock Maximum torque ................................................................................................................... 7,118 NM@60 rpm
Turret Turret Tools ...................................................................................................................................................... 12 Clamping way ............................................................................................. Hydraulic clamp with curvic coupling OD Shank ..................................................................................................................................................... 1.25” Diameter of Boring Bar ......................................................................................................... 2.5” STD / 3.15” opt
Travel X Axis .......................................................................................................................................................... 19.29” Z Axis ........................................................................................................................................................ 118.11” Feed motor X Z Axis ................................................................................................................................... 9.4HP X Z Axis Rapid Feedrate ................................................................................................................. 394 / 472ipm
Tailstock (Programmable position and quill) Travel (w/o Steady Rest) .......................................................................................................................... 118.11” Quill Travel .................................................................................................................................................... 3.94” Quill Diameter ................................................................................................................................................ 7.87 Quill Taper ................................................................................................................................. MT6 Rotary Quill
General Information Slide way Slant ................................................................................................................................................ 45˚ Coolant Pump ............................................................................................................................................. 1.6HP Machine Dimensions w/ conveyor (LxWxH) ................................................................... 338.66” x 117” x 99.60” Machine Weight ................................................................................................................................... 50,600 lbs
Page 4 of 13 FBL-530 Lathe
Floor Space
Page 5 of 13 FBL-530 Lathe
Machine Work Range
Standard Accessories Tooling • 10.4” LCD color screen • (4) 2.5” Boring bar holders
• 3-color cycle light • (1) Face & OD holder
• Air condition electrical cabinet • (1) Face & ID holder
• Automatic lubrication system • (1) OD tool holder
• Chip conveyor and bucket • (1) set boring bar sleeve
• Coolant system • Tool box with tool
• Hydraulic system
• Leveling bolts and pads
• Programmable tailstock w/ MT6 rotary quill
• Work lamp
• Machine operation manual
• Control programming manual
• Oil skimmer
• Base of steady rest ready
• Hydraulic steady rest pre-wired ready
Page 6 of 13 FBL-530 Lathe
(Solid 45 degree box ways design)
Page 7 of 13 FBL-530 Lathe
(4-Speed Gear headstock, Spindle bore 7.7”, Maximum torque: 7,118 NM@60 rpm)
(12-station Turret w/ hydraulic clamping curvic coupling)
(Programmable Tailstock with MT6 Live quill offers heavy loads)
Page 8 of 13 FBL-530 Lathe
(Optional large Pneumatic chuck)
Page 9 of 13 FBL-530 Lathe
Control Features:
FANUC
Description 0i-TD
Controlled axis
Controlled axis : 8
Simultaneous controlled axis: 4
10.4” TFT LCD ●
Cs-axis control ●
Simply sym servo controlled ●
Inch/metric conversion ●
Over travel ●
Stored stroke check 1 ●
Stored stroke check 2 X
Stored stroke check 3 X
Stroke limit check before move ●
Chuck and tail stock barrier ●
Mirror image ●
Chamfering on/off ●
Backlash compensation ●
Backlash compensation for each
Rapid traverse and cutting feed
●
Stored pitch error compensation ●
Position switch ●
Operation 0iTD
Automatic operation (memory) ●
DNC operation ●
MDI operation ●
DNC operation with Cf card
Program number search ●
Sequence number search ●
Sequence number compare and
stop ●
Program restart ●
Dry run ●
Single block ●
JOG feed (JOG) ●
Optional stop
Block skip ●
Manual reference position return ●
Manual hand feed rate *1,*10,*100 ●
Handle interruption ●
Page 10 of 13 FBL-530 Lathe
FANUC
Description 0i-TD
Skip function ●
Reference position return ●
Reference position return check ●
2nd reference position return ●
3rd/4th reference position return ●
Interpolation functions
Positioning ●
Linear interpolation ●
Circular interpolation ●
Dwell ●
Polar coordinate interpolation ●
Cylindrical interpolation △
Helical interpolation △
Threading/synchronous cutting ●
Multiple Threading ●
Threading retract ●
Continuous threading ●
Variable lead threading ●
Circular threading △
Polygon turning ●
Polygon machining with two
spindles ●
Feed function
Rapid traverse tare ●
Rapid traverse override F0,25,50,100
%
●
Feed per minute ●
Feed per revolution ●
Tangential speed constant control ●
Linear acceleration/deceleration
After cutting feed interpolation
●
Feed rate override 0~150 % ●
Jog feed rate override ●
Override cancel ●
Manual per revolution feed ●
Rigid tapping ●
Program input
Label skip ●
Optional block skip ●
Page 11 of 13 FBL-530 Lathe
FANUC
Description 0i-TD
Program number O 4digits ●
Sequence number N 5digits ●
Absolute/incremental programming
Decimal point/Pocket
●
Rotary axis designation ●
Rotary axis roll over function ●
Coordinate system setting ●
Auto coordinate system setting ●
Direct input of coordinate system
shift ●
Workpiece coordinate system ●
Workpiece coordinate system preset ●
Direct drawing dimension
programming ●
G code system A ●
B/C ●
Chamfering / corner R ●
Programmable data input ●
Sub program call ●
Custom macro B ●
Canned cycles ●
Multiple repetitive cycle ●
Multiple repetitive cycle Ⅱ ●
Canned cycles for drilling ●
Circular interpolation by R programming ●
Manual guide i 10.4 “ color LCD ●
Auxiliary/Spindle function
2nd Auxiliary function : B8-digit ●
Auxiliary function lock ●
Spindle speed function ●
Constant surface speed control ●
Spindle speed override ●
Actual spindle speed output ●
Spindle speed fluctuation detection ●
Spindle orientation ●
Tool function / Tool compensation
Too offset pairs 64 pairs ●
Tool function:T8 digits ●
Tool offset ●
Page 12 of 13 FBL-530 Lathe
FANUC
Description 0i-TD
Tool nose radius compensation ●
Tool geometry/wear compensation ●
Tool life management ●
Tool offset counter input ●
Automatic tool offset ●
Direct input of tool offset value measure ●
Direct input of tool offset value measure B ●
Editing operation
1280M ●
Number of register programs 400 pairs ●
Part program editing ●
Program protect ●
Background editing ●
Extended parts program editing ●
Setting & display
Status display ●
Current position display ●
Program display ●
Parameter setting and display ●
Self-diagnosis function ●
Alarm display ●
Alarm history display ●
Operator message history display ●
Help function ●
Run hour and parts count display ●
Actual cutting feed rate display ●
Display of spindle speed and T
code at all screens ●
Graphic display ●
Dynamic graphic display △
Data protection key △
Page 13 of 13 FBL-530 Lathe
Fanuc Control with 10.4” LCD screen and Manual Guide I conversational program
ONE-YEAR PARTS/LABOR WARRANTY ON MACHINE TWO-YEAR PARTS/LABOR WARRANTY ON CONTROL
Price is F.O.B. Santa Fe Springs, CA or Port of Entry. All list prices of optional accessories are good for new machine orders only Prices for in-field upgrades or retrofit options may vary from this price list