187 Fax 800-528-2554 www.cfcdist.com Feather Sheets - Stainless Steel - JD CF337717 Right hand sheet, 66-7/16”. 000619 $200.00 CF337718 Left hand sheet, 66-7/16”. 000617 $200.00 CF337719 Right hand sheet, 75-5/16”. 025917 $244.00 CF337720 Left hand sheet, 75-5/16”. 025913 $244.00 CF337714 Center sheet, 31-7/16”. 021116 $139.00 CF337716 Center sheet, 43-7/16”. 086119 $146.00 CF337721 Right hand sheet, 78-7/16”. 027029 $259.00 CF337722 Left hand sheet, 78-7/16”. 027024 $259.00 CF337715 Center sheet, 40-7/16”. 023218 $154.00 KHDW15 Complete hardware kit for 213, 215, 216, 913, 915 heads. 00411 $20.00 KHDW20 Complete hardware kit for 218, 220, 222, 224, 918, 920, 922, and 924 heads. 02818 $26.00 KHDW25 Complete hardware kit for 925 and 930 heads. 08326 $34.00 Order No. Description Stock Retail Quantities Required for Each head Order No. 213/913 215 915 216 218/918 220/920 222/922 224/924 925 930 CF337717 1 1 CF337718 1 1 CF337719 1 1 1 1 CF337720 1 1 1 1 CF337714 1 1 2 2 1 2 4 CF337716 1 1 3 2 CF337721 1 1 1 1 CF337722 1 1 1 1 CF337715 2 2 John Deere 200 and 900 series headers Special note: 200 series heads must be installed in complete sets when replacing painted metal top sheets. CF314214 Center sheet, 66 13/16”, requires 6 bolts. 623629 $329.00 CF314213 Left sheet, 87”, requires 9 bolts. 061236 $402.00 CF313002 Right Sheet, 87” requires 9 bolts. 061234 $402.00 CF314212 Left sheet, 117”, requires 12 bolts. 025738 $469.00 CF313001 Right sheet, 117”, requires 11 bolts. 025731 $469.00 CF314217 Left inside sheet, 60 15/16”, requires 5 bolts. 002728 $340.00 CF314216 Right inside sheet, 60 15/16”, requires 5 bolts. 002724 $340.00 CF314219 Left inside sheet, 90 7/8”, requires 8 bolts. 008236 $410.00 CF314218 Right inside sheet, 90 7/8”, requires 8 bolts. 008234 $410.00 CF312374 Shoulder bolt 8 mm x 15.6 mm. 3319 $1.90 Order No. Description Stock Retail Stainless Steel Feather Sheets for 600 Series JD heads Model Left Left (inside) Center Right (inside) Right 620 CF314213 CF314214 CF313002 625 CF314212 CF314214 CF313001 630 CF314213 CF314217 CF314214 CF314216 CF313002 635 CF314213 CF314219 CF314214 CF314218 CF313002
Transcript
187Fax 800-528-2554 www.cfcdist.com
Feather Sheets - Stainless Steel - JD
CF337717 Right hand sheet, 66-7/16”. 000619 $200.00CF337718 Left hand sheet, 66-7/16”. 000617 $200.00CF337719 Right hand sheet, 75-5/16”. 025917 $244.00CF337720 Left hand sheet, 75-5/16”. 025913 $244.00CF337714 Center sheet, 31-7/16”. 021116 $139.00CF337716 Center sheet, 43-7/16”. 086119 $146.00CF337721 Right hand sheet, 78-7/16”. 027029 $259.00CF337722 Left hand sheet, 78-7/16”. 027024 $259.00CF337715 Center sheet, 40-7/16”. 023218 $154.00KHDW15 Complete hardware kit for 213, 215, 216, 913, 915 heads. 00411 $20.00KHDW20 Complete hardware kit for 218, 220, 222, 224, 918, 920, 922, and 924 heads. 02818 $26.00KHDW25 Complete hardware kit for 925 and 930 heads. 08326 $34.00
John Deere 200 and 900 series headersSpecial note: 200 series heads must be installed in complete sets when replacing painted metal top sheets.
CF314214 Center sheet, 66 13/16”, requires 6 bolts. 623629 $329.00CF314213 Left sheet, 87”, requires 9 bolts. 061236 $402.00CF313002 Right Sheet, 87” requires 9 bolts. 061234 $402.00CF314212 Left sheet, 117”, requires 12 bolts. 025738 $469.00CF313001 Right sheet, 117”, requires 11 bolts. 025731 $469.00CF314217 Left inside sheet, 60 15/16”, requires 5 bolts. 002728 $340.00CF314216 Right inside sheet, 60 15/16”, requires 5 bolts. 002724 $340.00CF314219 Left inside sheet, 90 7/8”, requires 8 bolts. 008236 $410.00CF314218 Right inside sheet, 90 7/8”, requires 8 bolts. 008234 $410.00CF312374 Shoulder bolt 8 mm x 15.6 mm. 3319 $1.90
Order No. Description Stock RetailStainless Steel Feather Sheets for 600 Series JD heads
Model Left Left (inside) Center Right (inside) Right 620 CF314213 CF314214 CF313002
625 CF314212 CF314214 CF313001
630 CF314213 CF314217 CF314214 CF314216 CF313002
635 CF314213 CF314219 CF314214 CF314218 CF313002
188CFC Distributors, Inc. Jan. 2020 Catalog Phone 800-548-6633
Center Floor Sheet kit - CIH 1020P1313156K Center Floor sheet kit for Case-IH 1020 platforms. Sold in kits only, total width is 109”.
Replaces CIH 1313156C2588419 $229.00
CF1307581 Lower retaining clip, includes hardware. To fasten back of bottom floor sheet on Case-IH 1020 platform.
3847 $6.90
CF1313160 Top retaining clip for Case-IH platform floor sheets. 5839 $5.50
Order No. Description Stock Retail
Floor Sheets- CIH 3020, NH 740CF
CF84401760 Floor sheet, center. 14-1/2” wide, stainless steel. For Case-IH 3020; New Holland 740CF.Head width (quantity used): 20’ (1); 25’ (1); 30’ single and double drive (1); 35’ single and double drive (1). Replaces CIH no. 84401760.
05838 $55.00
CF84401762 Floor sheet, right end. 10” wide, stainless steel. For Case-IH 3020; New Holland 740CF.Head width (quantity used): 20’ (1); 25’ (1); 30’ single drive (1); 35’ single drive (1). Replaces CIH no. 84401762.
85148 $59.40
CF84401764 Floor sheet, right inside. 12-1/2” wide, stainless steel. For Case-IH 3020; New Holland 740CF. Head width (quantity used): 20’ (8); 25’ (11); 30’ single and double drive (13); 35’ single and double drive (16). Replaces CIH no. 84401764.
49031 $44.20
CF84483537 Floor sheet, right end. 10” wide, stainless steel. For Case-IH 3020; New Holland 740CF.Head width (quantity used): 30’ double drive (1); 35’ double drive (1). Replaces CIH no. 84483537.
85144 $59.40
CF47428302 Floor sheet, left end. 12-3/4” wide, stainless steel. For Case-IH 3020; New Holland 740CF.Head width (quantity used): 20’ (1); 25’ (1); 30’ single and double drive (1); 35’ single and double drive (1). Replaces CIH no. 47428302.
70248 $60.10
CF84401763 Floor sheet, left inside. 12-1/2” wide, stainless steel. For Case-IH 3020; New Holland 740CF. Head width (quantity used): 20’ (9); 25’ (11); 30’ single and double drive (14); 35’ single and double drive (16). Replaces CIH no. 84401763.
49033 $44.20
HDW3020 Hardware kit for floor sheets used on Case-IH 3020; New Holland 740CF. 1 hardware kit per floor sheet. Kit includes 2 carriage bolts, washers, nuts
078 $1.00
Order No. Description Stock Retail
189Fax 800-528-2554 www.cfcdist.com
Auger Liner Kits - UHMW PolyCondensation and wet grain will not corrode poly lining when the metal is covered with 1/8” UHMW poly. Poly lining is much easier to replace than the factory metal. Simply rivet into place. Comes with hardware.
Order No. Description Stock Retail80631 Poly liner kit for 13’-16’ heads. 039316 $199.0080632 Poly liner kit for 18’-20’ heads. 034711 $249.0080633 Poly liner kit for 22’-24’ heads. 039027 $299.0081825 Poly liner kit for 25’ heads. 030326 $329.0081686 Poly liner kit for 30’ heads. 039724 $399.00
John Deere 200/900 and New Holland 972/973 Flex Heads
John Deere Corn Heads
Order No. Description Stock Retail82075 Poly liner kit for 40/90 series 4 row, 30” heads. 023621 $329.0082076 Poly liner kit for 40/90 series 6 row, 30” heads. 025135 $394.0082077 Poly liner kit for 40/90 series 8 row, 30” heads. 086538 $446.0082078 Poly liner kit for 90 series 12 row, 30” heads. 088241 $536.0082727 Poly liner kit for 606C. 025135 $394.0082728 Poly liner kit for 608C. 086538 $446.0082729 Poly liner kit for 612C. 088248 $536.00
Case-IH Corn Heads
Order No. Description Stock Retail82061 Poly liner kit for 800 series 4 row, 30” heads. 023621 $329.0082062 Poly liner kit for 800 series 6 row, 30” heads. 025135 $394.0082063 Poly liner kit for 800 series 8 row, 30” heads. 086538 $446.0082644 Poly liner kit for 900/1000 series 6 row, 30” heads. 025138 $394.0082645 Poly liner kit for 900/1000 series 8 row, 30” heads. 086531 $446.0082646 Poly liner kit for 900/1000 series 12 row, 30” heads. 088246 $536.0082649 Poly liner kit for 2200, 2400, 3200, 3400 - 8 Row 086539 $446.0082825 Poly liner kit for 2200, 2400, 3200, 3400 - 4 Row 023629 $329.0082826 Poly liner kit for 2200, 2400, 3200, 3400 - 6 Row 025139 $394.0082828 Poly liner kit for 2200, 2400, 3200, 3400 - 12 Row 088249 $536.00
Condensation and wet grain will not corrode poly lining when the metal is covered with white 1/8” UHMW poly. Poly lining is much easier to replace than the factory metal. Simply rivet into place. Comes with hard-ware.
Condensation and wet grain will not corrode poly lining when the metal is covered with white 1/8” UHMW poly. Poly lining is much easier to replace than the factory metal. Simply rivet into place. Comes with hard-ware.
190CFC Distributors, Inc. Jan. 2020 Catalog Phone 800-548-6633
Grain Tank Auger Floor Liner - PolyProtect the area in your grain tank that needs it the most and wears out the quickest. Install the CFC Grain Tank Auger Floor liner over new or worn tank floor. Allows for better feeding of the grain and protects the worn out steel.
Comes with 1/8” UHMW poly and stainless steel hold down strips.
Order No. Description Stock RetailCase-IH Combines
82579 Auger floor liner kit for all 1400 series. 008035 $385.0082580 Auger floor liner kit for all 1600 series. (Except 1620) 008034 $385.0082581 Auger floor liner kit for all 2100 series. 008039 $385.0082582 Auger floor liner kit for all 2300 and 2588 Series. 008039 $385.00
John Deere Combines
Order No. Description Stock RetailSS1 Stainless steel holddown strip for auger liners. 03315 $19.00
Rock Guard Kit - UHMW Poly*From a practical stand point, these items really take care of two problems. First, they act as a rock guard to eliminate stones and rocks from entering the feeder house. Secondly they trap soybeans from rolling off of the front of the platform during harvest.
We stagger the rock guards to allow the grain to get off of the cutterbar (unlike other rock guard units). Half of the rock guards installed approximately 4” behind the cutterbar and the other half is 2” behind the cutter bar overlapping the rear section by 1” to 2”. All mounting hardware and instructions included.
KCS13RGK Rock Guard kit, 13’ complete. 08278 $104.00KCS16RGK Rock Guard kit, 15’ or 16’ complete. 06984 $128.00KCS20RGK Rock Guard kit, 18’ or 20’ complete. 002115 $160.00KCS25RGK Rock Guard kit, 22’ thru 25’ complete. 000417 $200.00KCS30RGK Rock Guard kit, 30’ complete. 008619 $240.00KCS35RGK Rock Guard kit, 35’ complete. 006918 $280.00
Order No. Description Stock RetailThe rock guard sections are held in place by pop rivets.
