ARTIK ART AND ARCHITECTURE ADDENDUM #1 February 12 th , 2016 PAGE 1 OF 3 ADDENDUM #1 SANTA CLARA COUNTY OFFICE OF EDUCATION TENANT IMPROVEMENTS FOR SANTA CLARA COUNTY OFFICE OF EDUCATION Prepared by Architect Artik Art and Architecture 394-A Umbarger Road San Jose, Ca 95127 (408) 224-9890 This Addendum forms a part of the Contract Documents and modifies the original bidding documents as noted below. Contractor must acknowledge receipt of this Addendum in the space provided on the Bid Form. Failure to do so may subject the Contractor to disqualification. CLARIFICATIONS Item 1 Clarify: Article 31 “Permits and Licenses” of Bid Document. A. Yes, the contractor shall secure, at Contractor’s sole cost and expense Permits, including building permits. Item 2 Clarify: Professional Liability Insurance. A. As follows: i. Commercial General Liability Insurance with limits not less than $1,000,000 (one million dollars) each occurrence Combined Single Limit for Bodily Injury and Property Damage (including coverage for claims of sexual abuse and molestation). ii. Workers’ Compensation Insurance, with Employer’s Liability limits not less than $1,000,000 (one million dollars) each accident. iii. Professional Liability (E & O) Insurance with limits not less than $1,000,000.00 (one million dollars) each occurrence and in the aggregate. Coverage must at a minimum apply to negligent Errors and Omissions arising out of professional services, performed under the contract, with any deductible not to exceed $100,000 each claim. CHANGES TO THE SPECIFICATIONS Item 3 Affirmative Action Employment Program B. Added specification section in its entirety. Item 4 Specification Section 09 30 00 Tiling C. Added specification section in its entirety. Item 5 Specification Section 10 21 13 Toilet Compartments
Transcript
ARTIK ART AND ARCHITECTURE ADDENDUM #1 February 12th, 2016
PAGE 1 OF 3
ADDENDUM #1
SANTA CLARA COUNTY OFFICE OF EDUCATION TENANT IMPROVEMENTS
FOR
SANTA CLARA COUNTY OFFICE OF EDUCATION
Prepared by Architect
Artik Art and Architecture 394-A Umbarger Road
San Jose, Ca 95127 (408) 224-9890
This Addendum forms a part of the Contract Documents and modifies the original bidding documents as noted below. Contractor must acknowledge receipt of this Addendum in the space provided on the Bid Form. Failure to do so may subject the Contractor to disqualification. CLARIFICATIONS
Item 1 Clarify: Article 31 “Permits and Licenses” of Bid Document. A. Yes, the contractor shall secure, at Contractor’s sole cost and expense Permits,
including building permits.
Item 2 Clarify: Professional Liability Insurance. A. As follows:
i. Commercial General Liability Insurance with limits not less than $1,000,000 (one million dollars) each occurrence Combined Single Limit for Bodily Injury and Property Damage (including coverage for claims of sexual abuse and molestation).
ii. Workers’ Compensation Insurance, with Employer’s Liability limits not less than $1,000,000 (one million dollars) each accident.
iii. Professional Liability (E & O) Insurance with limits not less than $1,000,000.00 (one million dollars) each occurrence and in the aggregate. Coverage must at a minimum apply to negligent Errors and Omissions arising out of professional services, performed under the contract, with any deductible not to exceed $100,000 each claim.
CHANGES TO THE SPECIFICATIONS
Item 3 Affirmative Action Employment Program B. Added specification section in its entirety.
ARTIK ART AND ARCHITECTURE ADDENDUM #1 February 12th, 2016
PAGE 2 OF 3
A. Added specification section in its entirety.
Item 6 Specification Section 10 28 00 Toilet, Bath, and Laundry Accessories A. Added specification section in its entirety.
CHANGES TO THE DRAWINGS Architectural:
Item 1 A0.01 Title Sheet A. Revised Scope of Work. Refer to attached drawing AD01-A1. B. Revised General Notes. Refer to attached drawing AD01-A2. C. Added sheet A0.02 to Sheet Index. Refer to attached drawings AD01-A3.
Item 2 A0.02 CALGreen Mandatory Measures
A. Added sheet in its entirety. Refer to attached drawing AD01-A4.
Item 3 A1.10 Site Plan A. Detail 1: Revised curb ramps at accessible parking. Refer to attached drawing AD01-
A5. B. Keynotes: Revised Keynotes 02 and 03, and added Keyntoes 06 and 07. Refer to
attached drawing AD01-A6. Item 4 A2.10 Building One Second Floor Demolition Plan
A. Detail 1: Revised extent of demolition work and added Keynote 4 to plan. Refer to attached drawing AD01-A7.
B. Keynotes: Added Keynote 4. Refer to attached drawing AD01-A8.
Item 5 A3.11 Building One Second Floor Plan A. Detail 1: Revised extent of work at restrooms and drinking fountain, and added
enlarged plan call-out. Refer to attached drawing AD01-A9. B. Keynotes: Added Keynote 4. Refer to attached drawing AD01-A10. C. Legend: Added wall hatches to Legend. Refer to attached drawing AD01-A11.
Item 6 A3.21 Building One Third Floor Plan
A. Detail 1: Revised extent of work at restrooms and drinking fountain, and added enlarged plan call-out. Refer to attached drawing AD01-A12.
B. Keynotes: Added Keynote 4. Refer to attached drawing AD01-A113. C. Legend: Added wall hatches to Legend. Refer to attached drawing AD01-A14.
Item 7 A3.30 Building One Enlarged Floor Plans
A. Legend: Revised detail references. Refer to attached drawing AD01-A15. B. Detail 3: Added wall type marker ‘1A’ and portion of new wall and drinking
fountain. Refer to attached drawing AD01-A16.
Item 8 A3.31 Building One Restroom Floor Plans A. Added sheet in its entirety. Refer to attached drawing AD01-A17.
Item 9 A12.10 Site Details
A. Added sheet in its entirety. Refer to attached drawing AD01-A18.
ARTIK ART AND ARCHITECTURE ADDENDUM #1 February 12th, 2016
PAGE 3 OF 3
Item 10 A12.30 Details A. Detail 4: Revised detail as shown. Refer to attached drawing AD01-A19. B. Detail 14: Added detail in its entirety. Refer to attached drawing AD01-A20. C. Detail 15: Added detail in its entirety. Refer to attached drawing AD01-A21. D. Detail 18: Added detail in its entirety. Refer to attached drawing AD01-A22. E. Detail 21: Added detail in its entirety. Refer to attached drawing AD01-A23. F. Detail 22: Added detail in its entirety. Refer to attached drawing AD01-A24. G. Detail 24: Added detail in its entirety. Refer to attached drawing AD01-A25. H. Detail 26: Added detail in its entirety. Refer to attached drawing AD01-A26. I. Detail 27: Added detail in its entirety. Refer to attached drawing AD01-A27.
Plumbing:
Item 1 P3.1 Plumbing Enlarged Plans A. Added sheet in its entirety. Refer to attached drawing AD01-P1.
Electrical:
Item 1 EP2.2 Level 2 Electrical Power Plan A. Added power for drinking fountain and keynote 4. Refer to attached drawing AD01-
E1.
Item 2 EP2.3 Level 3 Electrical Power Plan B. Added power for drinking fountain and keynote 4. Refer to attached drawing AD01-
APPROVED: January 13, 1976 BY: Santa Clara County Board of Education SECTION 12, CONTRACT COMPLIANCE
12.1 The Santa Clara County Office of Education will maintain a list of minority businesses and businesses
operated by women that will ensure that such businesses receive solicitations for bids. 12.2 The Santa Clara County Office of Education will maintain a list of minority and woman consultants and
will ensure that they are afforded equal opportunity for contracts. 12.3 The Santa Clara County Office of Education will notify its vendors, suppliers, and other contractors of
its affirmative action program. 12.4 The Santa Clara County Office of Education will require the inclusion of the following equal opportunity
clauses as a condition of all contracts in excess of $10,000.
During the performance of this contract, the contractor agrees as follows:
12.4.1 The contractor will not discriminate against any employee or applicant for employment because of race, creed, color sex, or national origin. Such action shall include, but not be limited to the following: employment, upgrading, demotion or
transfer; recruitment or recruitment advertising, layoff or termination; rates of pay or other forms of compensation; and a selection for training, including apprenticeship. The contractor agrees to post in conspicuous places, available to employees and applicants for employment, notices setting forth the provisions of this nondiscrimination clause.
12.4.2 The contractor will, in all solicitation or advertisements for employees placed by or on behalf of the contractor, state that all qualified applicants will receive consideration for employment without regard to race, creed, color, physical handicap, sex, or national origin.
12.4.2 The contractor will show evidence of compliance with all provision of executive
Order 11246, as amended, and of the rules, regulations, and relevant orders of the Secretary of Labor.
12.4.3 In the event of the contractor’s noncompliance with the nondiscrimination clauses of this
contract or with any of the said rules, regulations, or orders, this contractor may be declared ineligible for further contracts with this office.
ARTIK ART & ARCHITECTURE 09 30 00 TILING
PAGE 1
SECTION 09 30 00 TILING
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
1.2 SUMMARY
A. Section Includes:
1. Ceramic tile.
B. Related Sections:
1. Section 07 92 00 "Joint Sealants" for sealing of expansion, contraction, control, and isolation joints in tile surfaces.
A. General: Definitions in the ANSI A108 series of tile installation standards and in ANSI A137.1 apply to Work of this Section unless otherwise specified.
B. ANSI A108 Series: ANSI A108.01, ANSI A108.02, ANSI A108.1A, ANSI A108.1B, ANSI A108.1C, ANSI A108.4, ANSI A108.5, ANSI A108.6, ANSI A108.8, ANSI A108.9, ANSI A108.10, ANSI A108.11, ANSI A108.12, ANSI A108.13, ANSI A108.14, ANSI A108.15, ANSI A108.16, and ANSI A108.17, which are contained in "American National Standard Specifications for Installation of Ceramic Tile."
C. Module Size: Actual tile size plus joint width indicated.
D. Face Size: Actual tile size, excluding spacer lugs.
1.4 PERFORMANCE REQUIREMENTS
A. Static Coefficient of Friction: For tile installed on walkway surfaces, provide products with the following values as determined by testing identical products per ASTM C 1028:
1. Level Surfaces: Minimum 0.6.
ARTIK ART & ARCHITECTURE 09 30 00 TILING
PAGE 2
1.5 ACTION SUBMITTALS
A. Product Data: For each type of product indicated.
B. Shop Drawings: Show locations of each type of tile and tile pattern. Show widths, details, and locations of expansion, contraction, control, and isolation joints in tile substrates and finished tile surfaces.
C. Samples for Verification:
1. Full-size units of each type and composition of tile and for each color and finish required. For ceramic mosaic tile in color blend patterns, provide full sheets of each color blend.
1.6 INFORMATIONAL SUBMITTALS
A. Qualification Data: For qualified Installer.
B. Master Grade Certificates: For each shipment, type, and composition of tile, signed by tile manufacturer and Installer.
C. Product Certificates: For each type of product, signed by product manufacturer.
D. Material Test Reports: For each tile-setting and -grouting product.
1.7 MAINTENANCE MATERIAL SUBMITTALS
A. Furnish extra materials that match and are from same production runs as products installed and that are packaged with protective covering for storage and identified with labels describing contents.
1. Tile and Trim Units: Furnish quantity of full-size units equal to 3 percent of amount installed for each type, composition, color, pattern, and size indicated.
2. Grout: Furnish quantity of grout equal to 3 percent of amount installed for each type, composition, and color indicated.
1.8 QUALITY ASSURANCE
A. Source Limitations for Tile: Obtain tile from one source or producer.
1. Obtain tile of each type and color or finish from same production run and of consistent quality in appearance and physical properties for each contiguous area.
B. Source Limitations for Setting and Grouting Materials: Obtain ingredients of a uniform quality for each mortar, adhesive, and grout component from one manufacturer and each aggregate from one source or producer.
ARTIK ART & ARCHITECTURE 09 30 00 TILING
PAGE 3
1.9 DELIVERY, STORAGE, AND HANDLING
A. Deliver and store packaged materials in original containers with seals unbroken and labels intact until time of use. Comply with requirements in ANSI A137.1 for labeling tile packages.
B. Store tile and cementitious materials on elevated platforms, under cover, and in a dry location.
C. Store aggregates where grading and other required characteristics can be maintained and contamination can be avoided.
D. Store liquid materials in unopened containers and protected from freezing.
E. Handle tile that has temporary protective coating on exposed surfaces to prevent coated surfaces from contacting backs or edges of other units. If coating does contact bonding surfaces of tile, remove coating from bonding surfaces before setting tile.
1.10 PROJECT CONDITIONS
A. Environmental Limitations: Do not install tile until construction in spaces is complete and ambient temperature and humidity conditions are maintained at the levels indicated in referenced standards and manufacturer's written instructions.
PART 2 - PRODUCTS
2.1 PRODUCTS, GENERAL
A. ANSI Ceramic Tile Standard: Provide tile that complies with ANSI A137.1 for types, compositions, and other characteristics indicated.
B. ANSI Standards for Tile Installation Materials: Provide materials complying with ANSI A108.02, ANSI standards referenced in other Part 2 articles, ANSI standards referenced by TCA installation methods specified in tile installation schedules, and other requirements specified.
C. Low-Emitting Materials: Tile flooring systems shall comply with the testing and product requirements of the California Department of Health Services' "Standard Practice for the Testing of Volatile Organic Emissions from Various Sources Using Small-Scale Environmental Chambers."
D. Factory Blending: For tile exhibiting color variations within ranges, blend tile in factory and package so tile units taken from one package show same range in colors as those taken from other packages and match approved Samples.
E. Mounting: For factory-mounted tile, provide back- or edge-mounted tile assemblies as standard with manufacturer unless otherwise indicated.
ARTIK ART & ARCHITECTURE 09 30 00 TILING
PAGE 4
2.2 TILE PRODUCTS
A. Factory-mounted unglazed ceramic mosaic tile.
1. Basis-of-Design Product: Subject to compliance with requirements, provide product indicated on Drawings or comparable product by one of the following:
a. American Olean; Division of Dal-Tile International Inc.
b. Daltile; Division of Dal-Tile International Inc.
c. Interceramic.
d. Or equal.
2. Composition: Vitreous or impervious natural clay or porcelain. 3. Module Size: 2 by 2 inches. 4. Thickness: 1/4 inch. 5. Face: Plain with cushion edges. 6. Surface: Slip-resistant, with abrasive admixture. 7. Finish: Mat, clear glaze. 8. Tile Color and Pattern: per Drawings. 9. Grout Color: As selected by Architect from manufacturer's full range.
B. Glazed wall tile.
1. Basis-of-Design Product: Subject to compliance with requirements, provide Daltile Semi-Gloss and Semi-Gloss Color Trends or comparable product by one of the following:
a. Daltile; Division of Dal-Tile International Inc.
b. American Olean; Division of Dal-Tile International Inc.
c. United States Ceramic Tile Company.
d. Or equal.
2. Module Size: 4-1/4 by 4-1/4 inches. 3. Thickness: 5/16 inch. 4. Face: Plain with modified square edges or cushion edges. 5. Finish: Bright, clear glaze. 6. Tile Color and Pattern: per Drawings. 7. Grout Color: As selected by Architect from manufacturer's full range. 8. Mounting: Factory, back mounted. 9. Mounting: Pregrouted sheets of tiles factory assembled and grouted with manufacturer's
standard white silicone rubber. 10. Trim Units: Coordinated with sizes and coursing of adjoining flat tile where
applicable and matching characteristics of adjoining flat tile. Provide shapes as follows, selected from manufacturer's standard shapes: a. Base for Thin-Set Mortar Installations: Straight, module size 4-1/4 by 4-1/4 inches.
b. Wainscot Cap for Thin-Set Mortar Installations: Surface bullnose, module size 4-1/4 by 4-1/4 inches.
c. Wainscot Cap for Flush Conditions: Regular flat tile for conditions where tile wainscot is shown flush with wall surface above it, same size as adjoining flat tile.
d. External Corners for Thin-Set Mortar Installations: Surface bullnose, same size as adjoining flat tile.
e. Internal Corners: Field-butted square corners. For coved base and cap use angle pieces designed to fit with stretcher shapes.
C. Exterior Wall Tile: Through-body porcelain type ceramic tile as follows:
1. Basis-of-Design Product: Subject to compliance with requirements, provide:
a. Daltile; Division of Dal-Tile International Inc., Endurance Recycled Floor Tile
2. Face Size: 4 by 4 inches. 3. Thickness: 3/8 inch (9.5 mm). 4. Tile Color and Pattern: Francium, Manganese, and Barium. Refer to plans for Pattern 5. Grout Color: Antique White. 6. Physical Properties:
a. Water Absorption: ASTM C373, meets ANSI 137.1 average of 1 to 3 percent. b. Frost Resistance: ASTM C1026, no deterioration of surface or body. c. Breaking Strength: ASTM C648, Meets ANSI 127.1, average 325 lbf. d. Bond Strength: ASTM C482: Average 270 psi. e. Abrasive Hardness: ASTM C501, passed. f. Chemical Resistance: ASTM C650, 10% HCI, 10% KOH.
A. Latex-Portland Cement Mortar (Thin Set): ANSI A118.4.
1. For wall applications, provide mortar that complies with requirements for nonsagging mortar in addition to the other requirements in ANSI A118.4.
2.4 GROUT MATERIALS
A. Standard Cement Grout: ANSI A118.6.
B. Grout for Pregrouted Tile Sheets: Same product used in factory to pregrout tile sheets.
2.5 MISCELLANEOUS MATERIALS
A. Tile Cleaner: A neutral cleaner capable of removing soil and residue without harming tile and grout surfaces, specifically approved for materials and installations indicated by tile and grout manufacturers.
B. Grout Sealer: Manufacturer's standard product for sealing grout joints and that does not change color or appearance of grout.
2.6 MIXING MORTARS AND GROUT
A. Mix mortars and grouts to comply with referenced standards and mortar and grout manufacturers' written instructions.
B. Add materials, water, and additives in accurate proportions.
C. Obtain and use type of mixing equipment, mixer speeds, mixing containers, mixing time, and other procedures to produce mortars and grouts of uniform quality with optimum performance characteristics for installations indicated.
PART 3 - EXECUTION
3.1 EXAMINATION
A. Examine substrates, areas, and conditions where tile will be installed, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance of installed tile.
1. Verify that substrates for setting tile are firm, dry, clean, free of coatings that are incompatible with tile-setting materials including curing compounds and other substances that contain soap, wax, oil, or silicone; and comply with flatness tolerances required by ANSI A108.01 for installations indicated.
2. Verify that concrete substrates for tile floors installed with thin-set mortar comply with surface finish requirements in ANSI A108.01 for installations indicated.
a. Verify that surfaces that received a steel trowel finish have been mechanically scarified.
b. Verify that protrusions, bumps, and ridges have been removed by sanding or grinding.
3. Verify that installation of grounds, anchors, recessed frames, electrical and mechanical units of work, and similar items located in or behind tile has been completed.
4. Verify that joints and cracks in tile substrates are coordinated with tile joint locations; if not coordinated, adjust joint locations in consultation with Architect.
B. Proceed with installation only after unsatisfactory conditions have been corrected.
3.2 PREPARATION
A. Fill cracks, holes, and depressions in concrete substrates for tile floors installed with thin-set mortar with trowelable leveling and patching compound specifically recommended by tile-setting material manufacturer.
ARTIK ART & ARCHITECTURE 09 30 00 TILING
PAGE 7
B. Where indicated, prepare substrates to receive waterproofing by applying a reinforced mortar bed that complies with ANSI A108.1A and is sloped 1/4 inch per foot toward drains.
C. Blending: For tile exhibiting color variations, verify that tile has been factory blended and packaged so tile units taken from one package show same range of colors as those taken from other packages and match approved Samples. If not factory blended, either return to manufacturer or blend tiles at Project site before installing.
3.3 TILE INSTALLATION
A. Comply with TCA's "Handbook for Ceramic Tile Installation" for TCA installation methods specified in tile installation schedules. Comply with parts of the ANSI A108 Series "Specifications for Installation of Ceramic Tile" that are referenced in TCA installation methods, specified in tile installation schedules, and apply to types of setting and grouting materials used.
B. Extend tile work into recesses and under or behind equipment and fixtures to form complete covering without interruptions unless otherwise indicated. Terminate work neatly at obstructions, edges, and corners without disrupting pattern or joint alignments.
C. Accurately form intersections and returns. Perform cutting and drilling of tile without marring visible surfaces. Carefully grind cut edges of tile abutting trim, finish, or built-in items for straight aligned joints. Fit tile closely to electrical outlets, piping, fixtures, and other penetrations so plates, collars, or covers overlap tile.
D. Provide manufacturer's standard trim shapes where necessary to eliminate exposed tile edges.
E. Jointing Pattern: Lay tile in grid pattern unless otherwise indicated. Lay out tile work and center tile fields in both directions in each space or on each wall area. Lay out tile work to minimize the use of pieces that are less than half of a tile. Provide uniform joint widths unless otherwise indicated.
1. For tile mounted in sheets, make joints between tile sheets same width as joints within tile sheets so joints between sheets are not apparent in finished work.
2. Where adjoining tiles on floor, base, walls, or trim are specified or indicated to be same size, align joints.
3. Where tiles are specified or indicated to be whole integer multiples of adjoining tiles on floor, base, walls, or trim, align joints unless otherwise indicated.
F. Joint Widths: Unless otherwise indicated, install tile with the following joint widths:
G. Lay out tile wainscots to dimensions indicated or to next full tile beyond dimensions indicated.
H. Expansion Joints: Provide expansion joints and other sealant-filled joints, including control, contraction, and isolation joints, where indicated. Form joints during installation of setting materials, mortar beds, and tile. Do not saw-cut joints after installing tiles.
ARTIK ART & ARCHITECTURE 09 30 00 TILING
PAGE 8
1. Where joints occur in concrete substrates, locate joints in tile surfaces directly above them.
I. Grout Sealer: Apply grout sealer to cementitious grout joints in tile floors according to grout-sealer manufacturer's written instructions. As soon as grout sealer has penetrated grout joints, remove excess sealer and sealer from tile faces by wiping with soft cloth.
3.4 CLEANING AND PROTECTING
A. Cleaning: On completion of placement and grouting, clean all ceramic tile surfaces so they are free of foreign matter.
1. Remove latex-portland cement grout residue from tile as soon as possible. 2. Clean grout smears and haze from tile according to tile and grout manufacturer's written
instructions but no sooner than 10 days after installation. Use only cleaners recommended by tile and grout manufacturers and only after determining that cleaners are safe to use by testing on samples of tile and other surfaces to be cleaned. Protect metal surfaces and plumbing fixtures from effects of cleaning. Flush surfaces with clean water before and after cleaning.
B. Protect installed tile work with kraft paper or other heavy covering during construction period to prevent staining, damage, and wear. If recommended by tile manufacturer, apply coat of neutral protective cleaner to completed tile walls and floors.
C. Prohibit foot and wheel traffic from tiled floors for at least seven days after grouting is completed.
D. Before final inspection, remove protective coverings and rinse neutral protective cleaner from tile surfaces.
3.5 INTERIOR TILE INSTALLATION SCHEDULE
A. Interior Floor Installations, Concrete Subfloor:
a. Tile Type: Ceramic mosaic floor tile. b. Thin-Set Mortar: Latex- portland cement mortar. c. Grout: Polymer-modified unsanded grout. d. Grout: Water-cleanable epoxy grout.
B. Interior Wall Installations, Wood Studs or Furring:
1. Tile Installation W244: Thin-set mortar on cementitious backer units or fiber cement underlayment; TCA W244.
a. Tile Type: Glazed wall tile b. Thin-Set Mortar: Latex- portland cement mortar. c. Grout: Polymer-modified unsanded grout.
ARTIK ART & ARCHITECTURE 09 30 00 TILING
PAGE 9
C. Interior Wall Installations, Metal Studs or Furring:
1. Tile Installation W244: Thin-set mortar on cementitious backer units or fiber cement underlayment; TCA W244.
a. Tile Type: Glazed wall tile. b. Thin-Set Mortar: Latex- portland cement mortar. c. Grout: Polymer-modified unsanded grout.
END OF SECTION 09 30 00
ARTIK ART AND ARCHITECTURE 102113 TOILET COMPARTMENTS
SECTION 102113 TOILET COMPARTMENTS
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section.
1.2 SUMMARY
A. Section Includes: 1. Solid-color reinforced composite toilet compartments configured as toilet enclosures and
urinal screens.
B. Related Sections: 1. Division 10 Section "Toilet and Bath Accessories" for toilet tissue dispensers, grab bars,
purse shelves, and similar accessories.
1.3 ACTION SUBMITTALS
A. Product Data: For each type of product indicated. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes.
B. Shop Drawings: For toilet compartments. Include plans, elevations, sections, details, and attachments to other work.
1. Show locations of cutouts for compartment-mounted toilet accessories. 2. Show locations of reinforcements for compartment-mounted grab bars. 3. Show locations of centerlines of toilet fixtures. 4. Show overhead support or bracing locations.
C. Samples for Initial Selection: For each type of unit indicated. Include Samples of hardware and accessories involving material and color selection.
D. Samples for Verification: For the following products, in manufacturer's standard sizes unless otherwise indicated:
1. Each type of material, color, and finish required for units, prepared on 6-inch- (152-mm-) square Samples of same thickness and material indicated for Work.
2. Each type of hardware and accessory.
1.4 INFORMATIONAL SUBMITTALS
A. Product Certificates: For each type of toilet compartment, from manufacturer.
102113 - 1
ARTIK ART AND ARCHITECTURE 102113 TOILET COMPARTMENTS
1.5 CLOSEOUT SUBMITTALS
A. Maintenance Data: For toilet compartments to include in maintenance manuals.
1.6 QUALITY ASSURANCE
A. Surface-Burning Characteristics: As determined by testing identical products according to ASTM E 84, or another standard acceptable to authorities having jurisdiction, by a qualified testing agency. Identify products with appropriate markings of applicable testing agency.
1. Flame-Spread Index: 25 or less. 2. Smoke-Developed Index: 450 or less.
B. Regulatory Requirements: Comply with applicable provisions in the U.S. Architectural & Transportation Barriers Compliance Board's "Americans with Disabilities Act (ADA) and Architectural Barriers Act (ABA) Accessibility Guidelines for Buildings and Facilities" for toilet compartments designated as accessible.
1.7 PROJECT CONDITIONS
A. Field Measurements: Verify actual locations of toilet fixtures, walls, columns, ceilings, and other construction contiguous with toilet compartments by field measurements before fabrication.
PART 2 - PRODUCTS
2.1 MATERIALS
A. Aluminum Castings: ASTM B 26/B 26M.
B. Aluminum Extrusions: ASTM B 221 (ASTM B 221M).
C. Brass Castings: ASTM B 584.
D. Brass Extrusions: ASTM B 455.
E. Stainless-Steel Sheet: ASTM A 666, Type 304, stretcher-leveled standard of flatness.
F. Stainless-Steel Castings: ASTM A 743/A 743M.
G. Adhesives: Manufacturer's standard product that complies with the testing and product requirements of the California Department of Health Services' "Standard Practice for the Testing of Volatile Organic Emissions from Various Sources Using Small-Scale Environmental Chambers."
102113 - 2
ARTIK ART AND ARCHITECTURE 102113 TOILET COMPARTMENTS
2.2 SOLID-COLOR REINFORCED COMPOSITE UNITS
A. Basis-of-Design Product: Subject to compliance with requirements, provide:
1. Bobrick Washroom Equipment, 1092.67 Sierra Series
2. Or approved equal.
B. Toilet-Enclosure Style: Overhead braced.
C. Urinal-Screen Style: Overhead braced.
D. Door, Panel, Screen, and Pilaster Construction: Solid, solid-color reinforced composite panel material, not less than 3/4 inch thick, seamless, with eased edges and with homogenous color and pattern throughout thickness of material.
1. Color and Pattern: One color and pattern in each room as selected by Architect from manufacturer's full range.
E. Pilaster Shoes and Sleeves (Caps): Manufacturer's standard design; stainless steel.
F. Urinal-Screen Post: Manufacturer's standard post design of material matching the thickness and construction of pilasters; with shoe and sleeve (cap) matching that on the pilaster.
G. Brackets (Fittings):
1. Full-Height (Continuous) Type: Manufacturer's standard design; stainless steel. a. 18 gauge at toilet compartments, 11 gauge at urinal screens. b. Provide through-bolted, stainless steel, pin-in-head Torx sex bolt fasteners.
Through-bolted fasteners shall withstand direct pull force exceeding 1,500 lbs. per fastener.
2.3 ACCESSORIES
A. Hardware and Accessories: Manufacturer's standard design, heavy-duty operating hardware and accessories.
1. Material: Stainless steel. 2. Hinges: Manufacturer's standard continuous, 16 gauge, cam type that swings to a closed
or partially open position. a. Attach to door and stile with theft-resistant, pin-in-head Torx stainless steel
machine screws into factory installed, threaded brass inserts. Threaded brass inserts shall withstand a direct pull force exceeding 1,500 lbs per insert.
3. Latch and Keeper: Manufacturer's standard surface-mounted sliding latch unit requiring less than 5-lb of force to operate. a. Attach latch track to door with machine screws into factory installed threaded brass
inserts. Threaded brass inserts shall be factory installed for door hinge and latch connections and shall withstand a direct pull exceeding 1,500 lbs. per insert.
102113 - 3
ARTIK ART AND ARCHITECTURE 102113 TOILET COMPARTMENTS
b. Secure latch keeper to stile with through-bolted, stainless steel, pin-in-head Torx sex bolt fasteners. Fasteners shall withstand direct pull force exceeding 1,500 lbs. per fastener.
4. Coat Hook: Secured to door by through-bolted, theft-resistant, pin-in-head Torx stainless steel screws. Through-bolted fasteners shall withstand a direct pull force exceeding 1,500 lbs. per fastener.
5. Door Bumpers: Two 11-gauge (3mm) stainless steel door stop plates with attached rubber bumpers at each door.
6. Door Pull: Manufacturer's standard unit at out-swinging doors that complies with regulatory requirements for accessibility. Provide units on both sides of doors at compartments designated as accessible. Install below latch.
B. Overhead Bracing: Manufacturer's standard continuous, extruded-aluminum head rail with antigrip profile and in manufacturer's standard finish.
C. Anchorages and Fasteners: Unless otherwise noted, provide manufacturer's standard exposed fasteners of stainless steel or chrome-plated steel or brass, finished to match the items they are securing, with theft-resistant-type heads. Provide sex-type bolts for through-bolt applications. For concealed anchors, use stainless steel, hot-dip galvanized steel, or other rust-resistant, protective-coated steel.
2.4 FABRICATION
A. Overhead-Braced Units: Provide manufacturer's standard corrosion-resistant supports, leveling mechanism, and anchors at pilasters to suit floor conditions. Provide shoes at pilasters to conceal supports and leveling mechanism.
B. Urinal-Screen Posts: Provide manufacturer's standard corrosion-resistant anchoring assemblies with leveling adjustment at tops and bottoms of posts. Provide shoes and sleeves (caps) at posts to conceal anchorage.
C. Door Size and Swings: Unless otherwise indicated, provide 24-inch- (610-mm-) wide, in-swinging doors for standard toilet compartments and 36-inch- (914-mm-) wide doors with a minimum 32-inch- (813-mm-) wide, clear opening for compartments designated as accessible.
PART 3 - EXECUTION
3.1 INSTALLATION
A. General: Comply with manufacturer's written installation instructions. Install units rigid, straight, level, and plumb. Secure units in position with manufacturer's recommended anchoring devices.
1. Maximum Clearances:
a. Pilasters and Panels: 1/2 inch (13 mm). b. Panels and Walls: 1 inch (25 mm).
102113 - 4
ARTIK ART AND ARCHITECTURE 102113 TOILET COMPARTMENTS
B. Overhead-Braced Units: Secure pilasters to floor and level, plumb, and tighten. Set pilasters with anchors penetrating not less than 1-3/4 inches (44 mm) into structural floor unless otherwise indicated in manufacturer's written instructions. Secure continuous head rail to each pilaster with no fewer than two fasteners. Hang doors to align tops of doors with tops of panels, and adjust so tops of doors are parallel with overhead brace when doors are in closed position.
C. Urinal Screens: Attach with anchoring devices to suit supporting structure. Set units level and plumb, rigid, and secured to resist lateral impact.
3.2 ADJUSTING
A. Hardware Adjustment: Adjust and lubricate hardware according to hardware manufacturer's written instructions for proper operation. Set hinges on in-swinging doors to hold doors open approximately 30 degrees from closed position when unlatched. Set hinges on out-swinging doors to return doors to fully closed position.
END OF SECTION 10 21 13
102113 - 5
ARTIK ART & ARCHITECTURE 10 28 00 TOILET, BATH, AND LAUNDRY ACCESSORIES
SECTION 10 28 00 TOILET, BATH, AND LAUNDRY ACCESSORIES
PART 1 - GENERAL
1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
1.2 SUMMARY
A. Section Includes:
1. Public-use washroom accessories. 2. Underlavatory guards. 3. Electric Hand Driers
B. Owner-Furnished Material: Paper Towel Dispenser, Toilet Paper Dispenser, Soap Dispenser.
1.3 ACTION SUBMITTALS
A. Product Data: For each type of product indicated. Include the following:
1. Construction details and dimensions. 2. Anchoring and mounting requirements, including requirements for cutouts in other work
and substrate preparation. 3. Material and finish descriptions. 4. Features that will be included for Project. 5. Manufacturer's warranty.
B. Product Schedule: Indicating types, quantities, sizes, and installation locations by room of each accessory required.
1. Identify locations using room designations indicated. 2. Identify products using designations indicated.
1.4 INFORMATIONAL SUBMITTALS
A. Warranty: Sample of special warranty.
1.5 CLOSEOUT SUBMITTALS
A. Maintenance Data: For toilet and bath accessories to include in maintenance manuals.
PAGE 1
ARTIK ART & ARCHITECTURE 10 28 00 TOILET, BATH, AND LAUNDRY ACCESSORIES
1.6 QUALITY ASSURANCE
A. Source Limitations: For products listed together in the same Part 2 articles, obtain products from single source from single manufacturer.
1.7 COORDINATION
A. Coordinate accessory locations with other work to prevent interference with clearances required for access by people with disabilities, and for proper installation, adjustment, operation, cleaning, and servicing of accessories.
B. Deliver inserts and anchoring devices set into concrete or masonry as required to prevent delaying the Work.
1.8 WARRANTY
A. Special Mirror Warranty: Manufacturer's standard form in which manufacturer agrees to replace mirrors that develop visible silver spoilage defects and that fail in materials or workmanship within specified warranty period.
1. Warranty Period: 15 years from date of Substantial Completion.
PART 2 - PRODUCTS
2.1 MATERIALS
A. Stainless Steel: ASTM A 666, Type 304, 0.031-inch minimum nominal thickness unless otherwise indicated.
B. Brass: ASTM B 19, flat products; ASTM B 16/B 16M, rods, shapes, forgings, and flat products with finished edges; or ASTM B 30, castings.
C. Steel Sheet: ASTM A 1008/A 1008M, Designation CS (cold rolled, commercial steel), 0.036-inch minimum nominal thickness.
D. Galvanized-Steel Sheet: ASTM A 653/A 653M, with G60 hot-dip zinc coating.
E. Galvanized-Steel Mounting Devices: ASTM A 153/A 153M, hot-dip galvanized after fabrication.
F. Fasteners: Screws, bolts, and other devices of same material as accessory unit and tamper-and-theft resistant where exposed, and of galvanized steel where concealed.
G. Chrome Plating: ASTM B 456, Service Condition Number SC 2 (moderate service).
H. Mirrors: ASTM C 1503, Mirror Glazing Quality, clear-glass mirrors, nominal 6.0 mm thick.
I. ABS Plastic: Acrylonitrile-butadiene-styrene resin formulation.
PAGE 2
ARTIK ART & ARCHITECTURE 10 28 00 TOILET, BATH, AND LAUNDRY ACCESSORIES
2.2 PUBLIC-USE WASHROOM ACCESSORIES
A. Basis-of-Design Product: Subject to compliance with requirements, provide product indicated or comparable product by one of the following:
1. American Specialties, Inc. 2. Bobrick Washroom Equipment, Inc. 3. Bradley Corporation. 4. Or equal.
B. Grab Bar:
1. Basis-of-Design Product: Bobrick B-5806.99. 2. Mounting: Flanges with concealed fasteners. 3. Material: Stainless steel, 0.05 inch thick.
a. Finish: Smooth, No. 4 finish (satin) on ends and slip-resistant texture in grip area. 4. Outside Diameter: 1-1/2 inches. 5. Configuration and Length: As indicated on Drawings.
C. Mirror Unit:
1. Basis-of-Design Product: Bobrick B-165. 2. Frame: Stainless-steel channel. 3. Hangers: Produce rigid, tamper- and theft-resistant installation, using method indicated
below. a. One-piece, galvanized-steel, wall-hanger device with spring-action locking
mechanism to hold mirror unit in position with no exposed screws or bolts. 4. Size: 24 inches by 36 inches.
D. Electric Hand Dryer:
1. Basis-of-Design Product: Excel R76 IC Automatic Sensor Activated Hand Drier. 2. Installation: Recessed 3. Power Source: 110/120V 20 Amp
E. Coat Hook:
1. Basis-of-Design Product: Bobrick B-76717.
2. Mounting: Surface mounted on door at +38-40” A.F.F. and at +60” A.F.F.
F. Utility Shelf with Mop/Broom Holders:
1. Basis-of-Design Product: Bobrick B-239. 2. Description: Unit with shelf, hooks, and holders. 3. Length: 34 inches. 4. Quantity of Hooks: Four. 5. Quantity of Mop/Brooms Holders: Three, spring-loaded, rubber hat, cam type. 6. Material and Finish: Stainless Steel, No. 4 finish (satin).
a. Shelf: Not less than nominal 0.05 inch (1.3 mm) thick stainless steel.
ARTIK ART & ARCHITECTURE 10 28 00 TOILET, BATH, AND LAUNDRY ACCESSORIES
2.3 UNDERLAVATORY GUARDS
A. Manufacturers: Subject to compliance with requirements, provide products by one of the following:
1. Plumberex Specialty Products, Inc. 2. Truebro by IPS Corporation. 3. Or equal.
B. Underlavatory Guard:
1. Description: Insulating pipe covering for supply and drain piping assemblies that prevent direct contact with and burns from piping; allow service access without removing coverings.
2. Material and Finish: Antimicrobial, molded plastic, white.
2.4 FABRICATION
A. General: Fabricate units with tight seams and joints, and exposed edges rolled. Hang doors and access panels with full-length, continuous hinges. Equip units for concealed anchorage and with corrosion-resistant backing plates.
B. Keys: Provide universal keys for internal access to accessories for servicing and resupplying. Provide minimum of six keys to Owner's representative.
PART 3 - EXECUTION
3.1 INSTALLATION
A. Install accessories according to manufacturers' written instructions, using fasteners appropriate to substrate indicated and recommended by unit manufacturer. Install units level, plumb, and firmly anchored in locations and at heights indicated.
B. Grab Bars: Install to withstand a downward load of at least 250 lbf, when tested according to ASTM F 446.
3.2 ADJUSTING AND CLEANING
A. Adjust accessories for unencumbered, smooth operation. Replace damaged or defective items.
B. Remove temporary labels and protective coatings.
C. Clean and polish exposed surfaces according to manufacturer's written recommendations.
