FIX-BANDA

160

ATTENTION

FIX-BANDA should not be uses: Without previous adhesion tests in-

situ on the support in question.

In applications not described in thistechnical sheet without previouslyconsulting the Technical Department.

As the only waterproofing solution:FIX-BANDA itself does not replacewaterproof paint or mortar. Itcomplements them.

In plaster or plasterboard wallsw ithout previous primer byHIDROPRIMER.

Applying it without pressing properly.

Self-adhesive waterproof band for the protectionof joints and formation of corners exposed tocracking risks.

FIELDS OF APPLICATION

Pre-sealing in corners to reinforce thewaterproofing in these critical points,indoors, outdoors, terraces, balconies,swimming pools,...

Band to bridge expansion joints prior tothe application of a waterproofing.

TECHNICAL CHARACTERISTICS

FIX-BANDA is composed of a visco-elasticlayer of butyl rubber, coated with a nonwovenof polyester fibers, which allows thedeformation of the band in the transversedirection while limiting the deformation in thelongitudinal direction. It is compatible withmost supports such as terraces, balconies,decks, swimming pools...

HOW TO USE

Support:All the supports will always be resistant,solid, clean of dust, paint, wax, oil andgrease, and will be perfectly set.Fragile or very porous surfaces,

TECHNICAL DATA

NON-WOVEN FABRIC:• Type of fiber: Polyester• Mass per m2: 97 g/ml• Breaking strength: 45+10 N

BUTYL RUBBER:• Type of butyl: butyl-polyisobutylene• Loss of mass: <1% • Resistance to slippering of butyl at 5ºC: < 3 mm. (ISO 7390)• Resistance to slippering of butyl at 70ºC: < 3 mm. (ISO 7390)• Maximum elongation: >15%BAND SET:• Temperature of application: from +5ºC to +35ºC• Opertating temperature: from -30ºC to +80ºCSTORAGE:• In covered, dry and ventilated places: 36 months

DELIVERY:• It supplies: Roll of 10 ml. x 80 mm.

they must be previously treated with PRI­MFIX or with IMPRIMACION SELLADORS10 and let them dry at least 1 hour.

Application of the strip: remove the self-adhesive paper from only one side andstick it by pressing it firmly on the support.

lo con fuerza sobre el soporte. Proceedthe same with the other side of the band.Ensure that the band does not form airbubbles. Then we will paint it with FIX-TERRATS (roofs) or protect it with HIDRO­ELASTIC (terraces, balconies, ...)

FIELDS OF APPLICATION

Self-adhesive and waterproof sheet measuring25x25cm. composed of an elastic butyland a non-woven fabric. Ideal to ensurethe tightness in the DRAINS prior to theapplication of FIX-TERRATS FIBRA,FIXAQUA FILM, HIDROELASTIC,IMPERTOT, HIDROFIX,...

HOW TO USE

Supports:

All the supports will always be resistant,solid, clean of dust, dry, ...

161

Glue the sheet and press hard to get atotal grip.

Self-adhesive waterproof band to ensure thetightness in DRAINS, prior to the application ofthe waterproofing.

TECHNICAL CHARACTERISTICS

FIX-BANDA DRAIN is composed of a visco-elastic layer of butyl rubber, coated with anonwoven of polyester fibers, which allowsthe deformation of the sheet in both directions.It is compatible with most supports (exceptasphalt) such as aluminum, glass, concrete,mortar,... and is applicable on terraces,balconies, decks, swimming pool beaches...

TECHNICAL DATA

NON-WOVEN FABRIC:• Type of fiber: Polyester• Mass per m2: 1360 g/m2• Breaking strength: 45+10 N

BUTYL RUBBER:• Type of butyl: butyl-polyisobutylene• Loss of mass: <1% • Resistance to slippering of butyl at 5ºC: < 3 mm. (ISO 7390)• Resistance to slippering of butyl at 70ºC: < 3 mm. (ISO 7390)• Maximum elongation: >15%BAND SET:• Temperature of application: from +5ºC to +35ºC• Operating temperature: from -30ºC to +80ºCSTORAGE:• In covered, dry and ventilated places: 36 months

DELIVERY:• It supplies: Sheets of 25cm. x 25cm.

Plegar la lámina al otro lado del pre-corte.

Fold the sheet on the other side of thepre-cut.

Take a blade and make V cuts from thecenter to the perimeter.

The support must be solid, clean and dry Place the sheet in the center of the sumpto be sealed.

Following the pre-cut. Remove the protective paper from onlyone of the two parts.

The cuts should start at the perimeterand should reach the center of the drain.

Cut the entire sheet completelydiscovering the sump.

Paste the sheet neatly into the walls ofthe sump, and with it ....

... we will have the surface ready toreceive the waterproofing.

If the surface is very porous, very absorbent,disintegrates or is wet, apply a primerpreviously with PRIMFIX or with IMPRIMA­CION SELLADOR S10 and let it

dry 1 hour.Then follow the following application ins­tructions:

FIX-BANDA DRAIN