TEST RESULTS and REPORTfor
- Unless otherwise requested, test samples will be discarded 21 days from the report date.
- This report shall not be reproduced, except in full, without written approval from COLTS Laboratories.
- Results in this report only relate to the samples analyzed.
Z-ESO081617-02
by
Eagle
Importadores y Exportadores Solmaq SAS
Also Certified for testing by the Safety Equipment Institute
COLTS Laboratories maintains A2LA accreditation to ISO/IEC 17025 for the tests listed on Certificate # 1612.01. Any tests not included on this certificate have been identified on the appropriate test result page.
ANSI Z87.1-2015 High Impact Spectacles - Base Model
Eagle Clear Lens, Black Frame and Temples (U6)
PassZ-ESO081617-02-01 1
ANSI Z87.1-2015 Optional Transmittance Attributes (U)
Eagle Clear Lens, Black Frame and Temples (U6)
PassZ-ESO081617-02-02 7
ANSI Z87.1-2015 High Impact Spectacles - Tint Variant
Eagle Smoke Lens, Black Frame and Temples (U6L3)
PassZ-ESO081617-02-03 9
ANSI Z87.1-2015 Optional Transmittance Attributes (U,L)
Eagle Smoke Lens, Black Frame and Temples (U6L3)
PassZ-ESO081617-02-04 12
ANSI Z87.1-2015 High Impact Spectacles - Tint Variant
Eagle Indoor/Outdoor Lens, Black Frame and Temples (U6L2)
PassZ-ESO081617-02-05 19
ANSI Z87.1-2015 Optional Transmittance Attributes (U,L)
Eagle Indoor/Outdoor Lens, Black Frame and Temples (U6L2)
PassZ-ESO081617-02-06 22
Importadores y Exportadores Solmaq SAS
ReasonResults
Pass / FailTest/Models(s)Project ID
Z-ESO081617-02
Page
COLTS Laboratories702 Stevens AvenueOldsmar, FL 34677TEL: 727-725-2323FAX:727-725-8890Email:[email protected]:www.colts-laboratories.com
PRODUCTRESULTS
SUMMARYA2LA Accredited Certificate # 1612.01
Report Date: 9/15/2017
Final Conclusion:
On August 16, 2017, COLTS Laboratories received Spectacles: Eagle from Importadores y Exportadores Solmaq SAS. From August 30, 2017 through September 15, 2017 COLTS Laboratories tested these Spectacles in accordance with ANSI Z87.1-2015.
Clear Lens, Black Frame and Temples (U6)Product Description:
EagleANSI Z87.1-2015 High Impact Spectacles - Base ModelZ-ESO081617-02-01Project ID(s):
Report of:of Model(s):
Project
September 15, 2017Paulo Barriga
Date:Attn:
Bogotá,
Importadores y Exportadores Solmaq SAS
Report To:
Report Summary
The Spectacles: Eagle (Clear Lens, Black Frame and Temples (U6)) do comply with ANSI Z87.1-2015 for the test(s) performed for ANSI Z87.1-2015 High Impact Spectacles - Base Model.
COLTS Laboratories
702 Stevens AvenueOldsmar, FL 34677TEL: 727-725-2323FAX:727-725-8890Email:[email protected]:www.colts-laboratories.com A2LA Accredited Certificate # 1612.01
Carrera 30, número 15-30
Dale PayneTechnical Services ManagerVice-President & COO
Daryl Neely
COLTS LaboratoriesRespectfully submitted,
Please contact us should you have any questions concerning this report.
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 1 of 28
Protector lenses shall be free of:5.1.1Optical Qualitystriae, bubbles, waves and other visible defects which would impair the wearer's vision.
Acceptable Pass
Clear lenses shall have a luminous transmittance of not less than 85%.5.1.2Luminous Transmittance
Luminous Transmittance Acceptable Pass
Left Eye 92.0% PassRight Eye 91.9% Pass
Clear plano lenses shall not exhibit more than 3% haze.5.1.3Haze - Clear Lenses Only
Haze Acceptable Pass
Left Eye 0.42% PassRight Eye 0.42% Pass
The tolerance on refractive power, astigmatism and resolving power shall be as indicated below. The tolerance on prism and prism imbalance shall be as indicated below. Filter lenses of shade 9 or higher are exempt from this section.
5.1.4Spectacle Refractive Power, Astigmatism, Resolving Power, Prism and Prism Imbalance for Plano Protectors
Refractive Power (±0.06) Acceptable Pass
Left Eye -0.015 PassRight Eye -0.01 Pass
Astigmatism (0.06 Max) Acceptable Pass
Left Eye 0.025 PassRight Eye 0.02 Pass
Resolving Power (20 Min) Acceptable Pass
Left Eye Acceptable PassRight Eye Acceptable Pass
Complete Prism (0.50 Max) Acceptable Pass
Left Eye 0.071 PassRight Eye 0.050 Pass
Prismatic Imbalance Acceptable Pass
Vertical (0.25 Max) 0.05 PassHorizontal Base In/Out (In 0.25 Max; Out 0.50 Max) 0.10 in Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-01
Lab Temp (C): 23
Lab Rh: 49
Sample ID:Eagle
Clear Lens, Black Frame and Temples (U6)
9/15/2017
Report of: ANSI Z87.1-2015 High Impact Spectacles - Base Model
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 2 of 28
Protectors shall be free from:5.2Physical Requirementsprojections, sharp edges or other defects which are likely to cause discomfort or injury during use.
Acceptable Pass
Protectors shall not ignite or continue to glow once the rod is removed. Each externally exposed material (exclusive of textiles or elastic bands) shall be tested.
5.2.2Ignition (Spectacle)
Lens Acceptable Pass
Front Acceptable Pass
Temple Acceptable Pass
Sideshield N/A N/A
Other N/A N/AMetal components used in protectors shall be corrosion resistant to the degree that the function of the protector shall not be impaired by the corrosion and the protector can be worn as intended. Lenses and electrical components are excluded from these requirements.
5.2.3Corrosion Resistance of Metal Components
Corrosion Resistant Acceptable PassThe frames, lens housings or carriers and lens(es) shall cover an area of not less than 40 mm (34 mm for small head sizes) in width and 33 mm (28 mm for small head sizes) in height (elliptical) in front of each eye, centered on the geometrical center of the lens.
5.2.4Minimum Coverage Area
Minimum Coverage Area Acceptable PassAll protectors shall bear the permanent and legible markings in specified locations. Protector markings shall be placed in relatable proximity to each other on the product.
Manufacturer's marks or logos are exempt from the proximity requirement if they are clearly present elsewhere on the product.
5.3Required Protector Markings (Spectacles)
Markings permanent, legible and in relatable proximity Not Assessed Not AssessedNot assessed per customer request
Markings representative of other standards shall not interfere with or be intermixed with the markings required by this standard.
Not Assessed Not Assessed
Not assessed per customer request
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-01
Lab Temp (C): 23
Lab Rh: 49
Sample ID:Eagle
Clear Lens, Black Frame and Temples (U6)
9/15/2017
Report of: ANSI Z87.1-2015 High Impact Spectacles - Base Model
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 3 of 28
All protectors shall bear the permanent and legible markings in specified locations. Protector markings shall be placed in relatable proximity to each other on the product.
Manufacturer's marks or logos are exempt from the proximity requirement if they are clearly present elsewhere on the product.
5.3Required Protector Markings (Spectacles)
Complete Device Markings Not Assessed Not Assessed
In relatable proximity Not Assessed Not AssessedManufacturer's Mark or Logo Not Assessed Not AssessedZ87 Mark Not Assessed Not Assessed+ Mark Not Assessed Not AssessedH Mark (Coverage - small head sizes) Not Assessed Not AssessedLens Type (multiple claim sequence W,U,L,R,V,S) Not Assessed Not AssessedUse (multiple claim sequence D3,D4,D5) Not Assessed Not Assessed
Not assessed per customer request All original equipment manufacturers (OEM) and non-OEM aftermarket components not sold with the original device shall be tested.
5.6Aftermarket Components and Accessories
Aftermarket Components and Accessories Manufacturer requirement Not testableProtectors and replaceable components marked for impact protection in accordance with Table 3 shall meet applicable requirements of Section 6.
6.1.1Protectors Marked for Impact Protection
Impact requirements Acceptable Pass
Marking requirements Not Assessed Not AssessedNot assessed per customer request
Frames and shells shall meet the requirements for high mass impact and high velocity impact in order to be impact-rated. These components shall be tested as a complete device. For frames and shells to be used with prescription lenses, they shall be fitted with representative test lenses having a nominal plano power and the minimum lens thickness to be used by the manufacturer, in no case less than 2.0 mm (0.079 in.). Frames and shells are exempt from the penetration requirement
6.1.2Frames and Shells
Frames and Shells Acceptable Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-01
Lab Temp (C): 23
Lab Rh: 49
Sample ID:Eagle
Clear Lens, Black Frame and Temples (U6)
9/15/2017
Report of: ANSI Z87.1-2015 High Impact Spectacles - Base Model
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 4 of 28
Impact rated protectors shall provide continuous lateral coverage (i.e. no openings greater than 1.5mm in diameter) from the vertical plane of the lenses tangential to a point not less than 10 mm posterior to the corneal plane and not less than 10 mm in height (or 8 mm for the smaller headform) above and not less than 10 mm in height (or 8 mm for the smaller headform) below the horizontal plane centered on the eyes of the headform.
6.1.3Lateral (Side) Coverage
Lateral (Side) Coverage Acceptable PassThe complete device shall meet the protector acceptance criteria when impacted by a pointed projectile weighing a minimum of 500 g (17.6 oz) dropped from a height of at least 127 cm (50.0 in.).
6.2.2High Mass Impact
Left Eye Sample 1 Acceptable Pass
Left Eye Sample 2 Acceptable Pass
Right Eye Sample 3 Acceptable Pass
Right Eye Sample 4 Acceptable PassThe complete device shall meet the protector acceptance criteria when impacted by a 6.35 mm (0.25 in) diameter steel ball traveling at 150 feet per second.
6.2.3High Velocity Impact (Spectacles)
Left Eye Center 151 fps Pass
Left Eye 30° 152 fps Pass
Right Eye Center 151 fps Pass
Right Eye 30° 150 fps Pass
One Side 90° at 10mm Above (H - 8mm) 150 fps Pass
Opposite Side 90° at 10mm Below (H - 8mm) 151 fps PassLenses for all complete devices shall meet the protector acceptance criteria when penetrated by a weighted needle with a minimum total weight of 44.2 g (1.56 oz) dropped from a height of at least 127 cm (50.0 in.).
6.2.4Penetration Test (lenses only)
Left Eye Sample 1 Acceptable Pass
Left Eye Sample 2 Acceptable Pass
Right Eye Sample 3 Acceptable Pass
Right Eye Sample 4 Acceptable Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-01
Lab Temp (C): 23
Lab Rh: 49
Sample ID:Eagle
Clear Lens, Black Frame and Temples (U6)
9/15/2017
Report of: ANSI Z87.1-2015 High Impact Spectacles - Base Model
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 5 of 28
Clear plano, reader, magnifier and prescription lenses shall have a luminous transmission of not less than 85%. Representative test lenses of plano power may be substituted for prescription, reader or magnifier lenses in this test.
7.1Protectors with Clear Lenses
Transmittance Acceptable Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-01
Lab Temp (C): 23
Lab Rh: 49
Sample ID:Eagle
Clear Lens, Black Frame and Temples (U6)
9/15/2017
Report of: ANSI Z87.1-2015 High Impact Spectacles - Base Model
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 6 of 28
Final Conclusion:
On August 16, 2017, COLTS Laboratories received Spectacles: Eagle from Importadores y Exportadores Solmaq SAS. From August 30, 2017 through September 15, 2017 COLTS Laboratories tested these Spectacles in accordance with ANSI Z87.1-2015.
Clear Lens, Black Frame and Temples (U6)Product Description:
EagleANSI Z87.1-2015 Optional Transmittance Attributes (U)Z-ESO081617-02-02Project ID(s):
Report of:of Model(s):
Project
September 15, 2017Paulo Barriga
Date:Attn:
Bogotá,
Importadores y Exportadores Solmaq SAS
Report To:
Report Summary
The Spectacles: Eagle (Clear Lens, Black Frame and Temples (U6)) do comply with ANSI Z87.1-2015 for the test(s) performed for ANSI Z87.1-2015 Optional Transmittance Attributes (U).
COLTS Laboratories
702 Stevens AvenueOldsmar, FL 34677TEL: 727-725-2323FAX:727-725-8890Email:[email protected]:www.colts-laboratories.com A2LA Accredited Certificate # 1612.01
Carrera 30, número 15-30
Dale PayneTechnical Services ManagerVice-President & COO
Daryl Neely
COLTS LaboratoriesRespectfully submitted,
Please contact us should you have any questions concerning this report.
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 7 of 28
Optional transmittance characteristics of a protector are represented by a scale/shade number indicating its ability to filter optical radiation. They shall meet the requirements, including markings, of Tables 6, 7, 8 and 9, if claims of compliance are made. Special purpose filters shall meet the requirements of Table 10.
7Optical Radiation Protector Requirements
Transmittance Acceptable Pass
Markings Not Assessed Not AssessedNot assessed per customer request
Clear plano, reader, magnifier and prescription lenses shall have a luminous transmission of not less than 85%. Representative test lenses of plano power may be substituted for prescription, reader or magnifier lenses in this test.
7.1Protectors with Clear Lenses
Transmittance Acceptable PassWhen tested in accordance with Section 9.2, plano, reader, magnifier and prescription lenses that are marked as ultraviolet filter lenses shall comply with requirements of Table 7. Representative test lenses of plano power may be substituted for prescription, reader or magnifier lenses in this test.
7.2.1.1Ultraviolet Filter Lenses - Transmission Requirements
U.V. Far Acceptable Pass
Left Eye 0.000% PassRight Eye 0.000% Pass
U.V. Near Acceptable Pass
Left Eye 0.005% PassRight Eye 0.005% Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-02
Lab Temp (C): 23
Lab Rh: 50
Sample ID:Eagle
Clear Lens, Black Frame and Temples (U6)
9/15/2017
Report of: ANSI Z87.1-2015 Optional Transmittance Attributes (U)
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 8 of 28
Final Conclusion:
On August 16, 2017, COLTS Laboratories received Spectacles: Eagle from Importadores y Exportadores Solmaq SAS. From August 30, 2017 through September 15, 2017 COLTS Laboratories tested these Spectacles in accordance with ANSI Z87.1-2015.
Smoke Lens, Black Frame and Temples (U6L3)Product Description:
EagleANSI Z87.1-2015 High Impact Spectacles - Tint VariantZ-ESO081617-02-03Project ID(s):
Report of:of Model(s):
Project
September 15, 2017Paulo Barriga
Date:Attn:
Bogotá,
Importadores y Exportadores Solmaq SAS
Report To:
Report Summary
The Spectacles: Eagle (Smoke Lens, Black Frame and Temples (U6L3)) do comply with ANSI Z87.1-2015 for the test(s) performed for ANSI Z87.1-2015 High Impact Spectacles - Tint Variant.
COLTS Laboratories
702 Stevens AvenueOldsmar, FL 34677TEL: 727-725-2323FAX:727-725-8890Email:[email protected]:www.colts-laboratories.com A2LA Accredited Certificate # 1612.01
Carrera 30, número 15-30
Dale PayneTechnical Services ManagerVice-President & COO
Daryl Neely
COLTS LaboratoriesRespectfully submitted,
Please contact us should you have any questions concerning this report.
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 9 of 28
Protector lenses shall be free of:5.1.1Optical Qualitystriae, bubbles, waves and other visible defects which would impair the wearer's vision.
Acceptable Pass
All protectors shall bear the permanent and legible markings in specified locations as shown in Table 3. Markings for lens type and use applications shall be required only when claims for protection against the hazard or indicated use are made by the manufacturer.
Protector markings shall be placed in relatable proximity to each other on the product in the sequence specified below:
- Manufacturer's marks or logos - Designation of standard (Z87 or Z87-2, for prescription devices) - Individual claims of compliance - impact-rated marking (+) - lens type - use applications
Manufacturer's marks or logos are exempt from the proximity requirement if they are clearly present elsewhere on the product.
5.3Required Protector Markings (Spectacles)
Markings permanent, legible and in relatable proximity Not Assessed Not AssessedNot assessed per customer request
Markings representative of other standards shall not interfere with or be intermixed with the markings required by this standard.
Not Assessed Not Assessed
Not assessed per customer request Complete Device Markings Not Assessed Not Assessed
Sequence Correct Not Assessed Not AssessedMfg Mark or Logo Not Assessed Not AssessedZ87 Mark Not Assessed Not Assessed+ Mark Not Assessed Not AssessedH Mark (Coverage - small head sizes) Not Assessed Not AssessedLens Type (multiple claim sequence W,U,L,R,V,S) Not Assessed Not AssessedUse (multiple claim sequence D3,D4,D5) Not Assessed Not Assessed
Not assessed per customer request The complete device shall meet the protector acceptance criteria when impacted by a pointed projectile weighing a minimum of 500 g (17.6 oz) dropped from a height of at least 127 cm (50.0 in.).
6.2.2High Mass Impact
Left Eye Sample 1 Acceptable Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-03
Lab Temp (C): 23
Lab Rh: 49
Sample ID:Eagle
Smoke Lens, Black Frame and Temples (U6L3)
9/15/2017
Report of: ANSI Z87.1-2015 High Impact Spectacles - Tint Variant
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 10 of 28
The complete device shall meet the protector acceptance criteria when impacted by a pointed projectile weighing a minimum of 500 g (17.6 oz) dropped from a height of at least 127 cm (50.0 in.).
6.2.2High Mass Impact
Left Eye Sample 2 Acceptable Pass
Right Eye Sample 3 Acceptable Pass
Right Eye Sample 4 Acceptable PassThe complete device shall meet the protector acceptance criteria when impacted by a 6.35 mm (0.25 in) diameter steel ball traveling at 150 feet per second.
6.2.3High Velocity Impact (Spectacles)
Left Eye Center 152 fps Pass
Left Eye 30° 152 fps Pass
Right Eye Center 151 fps Pass
Right Eye 30° 149 fps Pass
One Side 90° at 10mm Above (H - 8mm) 152 fps Pass
Opposite Side 90° at 10mm Below (H - 8mm) 151 fps PassWhen tested in accordance with Section 9.2, plano, reader, magnifier and prescription lenses that are marked as special purpose filters shall meet the requirements of Table 10.Representative test lenses of plano power may be substituted for prescription, reader or magnifier lenses in this test.
7.2.1.1Special Purpose Filter Lenses - Transmission Requirements
Tinted Lenses (8% - 85%) Acceptable Pass
Left Eye 12.0% PassRight Eye 11.8% PassRatio (0.90 - 1.10) 1.017 Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-03
Lab Temp (C): 23
Lab Rh: 49
Sample ID:Eagle
Smoke Lens, Black Frame and Temples (U6L3)
9/15/2017
Report of: ANSI Z87.1-2015 High Impact Spectacles - Tint Variant
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 11 of 28
Final Conclusion:
On August 16, 2017, COLTS Laboratories received Spectacles: Eagle from Importadores y Exportadores Solmaq SAS. From August 30, 2017 through September 15, 2017 COLTS Laboratories tested these Spectacles in accordance with ANSI Z87.1-2015.
Smoke Lens, Black Frame and Temples (U6L3)Product Description:
EagleANSI Z87.1-2015 Optional Transmittance Attributes (U,L)Z-ESO081617-02-04Project ID(s):
Report of:of Model(s):
Project
September 15, 2017Paulo Barriga
Date:Attn:
Bogotá,
Importadores y Exportadores Solmaq SAS
Report To:
Report Summary
The Spectacles: Eagle (Smoke Lens, Black Frame and Temples (U6L3)) do comply with ANSI Z87.1-2015 for the test(s) performed for ANSI Z87.1-2015 Optional Transmittance Attributes (U,L).
COLTS Laboratories
702 Stevens AvenueOldsmar, FL 34677TEL: 727-725-2323FAX:727-725-8890Email:[email protected]:www.colts-laboratories.com A2LA Accredited Certificate # 1612.01
Carrera 30, número 15-30
Dale PayneTechnical Services ManagerVice-President & COO
Daryl Neely
COLTS LaboratoriesRespectfully submitted,
Please contact us should you have any questions concerning this report.
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 12 of 28
Optional transmittance characteristics of a protector are represented by a scale/shade number indicating its ability to filter optical radiation. They shall meet the requirements, including markings, of Tables 6, 7, 8 and 9, if claims of compliance are made. Special purpose filters shall meet the requirements of Table 10.
7Optical Radiation Protector Requirements
Transmittance Acceptable Pass
Markings Not Assessed Not AssessedNot assessed per customer request
When tested in accordance with Section 9.2, plano, reader, magnifier and prescription lenses that are marked as ultraviolet filter lenses shall comply with requirements of Table 7. Representative test lenses of plano power may be substituted for prescription, reader or magnifier lenses in this test.
7.2.1.1Ultraviolet Filter Lenses - Transmission Requirements
U.V. Far Acceptable Pass
Left Eye 0.000% PassRight Eye 0.000% Pass
U.V. Near Acceptable Pass
Left Eye 0.000% PassRight Eye 0.000% Pass
When tested in accordance with Section 9.2, plano, reader, magnifier and prescription lenses that are marked as visible light filter lenses shall comply with requirements of Table 9. Representative test lenses of plano power may be substituted for prescription, reader or magnifier lenses in this test.
7.2.1.1Visible Light Filter Lenses - Transmission Requirements
Visible Light Acceptable Pass
Left Eye 12.035% PassRight Eye 11.708% Pass
Visible light filters in the range of L1.3 through L3 shall also meet the transmittance requirements of Table 4 of ANSI Z80.3-2010, including traffic signal recognition and UV transmittance (high and prolonged exposure). Visible light filters in the range of L4 through L10 are too dark to be used for driving, but shall meet the UV transmittance (high and prolonged exposure) requirements of Table 4 of ANSI Z80.3-2010.
7.2.1.2Visible Light Filters
Traffic Signal Recognition - Color Limits and Chromaticity Coordinates
Acceptable Pass
Left Eye See charts PassRight Eye See charts Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-04
Lab Temp (C): 23
Lab Rh: 47
Sample ID:Eagle
Smoke Lens, Black Frame and Temples (U6L3)
9/15/2017
Report of: ANSI Z87.1-2015 Optional Transmittance Attributes (U,L)
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 13 of 28
Visible light filters in the range of L1.3 through L3 shall also meet the transmittance requirements of Table 4 of ANSI Z80.3-2010, including traffic signal recognition and UV transmittance (high and prolonged exposure). Visible light filters in the range of L4 through L10 are too dark to be used for driving, but shall meet the UV transmittance (high and prolonged exposure) requirements of Table 4 of ANSI Z80.3-2010.
7.2.1.2Visible Light Filters
Traffic Signal Recognition - Red Signal 8% Minimum Acceptable Pass
Left Eye 15.7237% PassRight Eye 15.4612% Pass
Traffic Signal Recognition - Yellow Signal 6% Minimum Acceptable Pass
Left Eye 12.3030% PassRight Eye 11.9796% Pass
Traffic Signal Recognition - Green Signal 6% Minimum Acceptable Pass
Left Eye 11.8168% PassRight Eye 11.4847% Pass
Mean UVB 1% Maximum Acceptable Pass
Left Eye 0.000% PassRight Eye 0.000% Pass
Mean UVA 0.5% Luminous Transmittance Maximum Acceptable Pass
Left Eye 0.000% PassRight Eye 0.000% Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-04
Lab Temp (C): 23
Lab Rh: 47
Sample ID:Eagle
Smoke Lens, Black Frame and Temples (U6L3)
9/15/2017
Report of: ANSI Z87.1-2015 Optional Transmittance Attributes (U,L)
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 14 of 28
TRANS x y L 3 ANSI Z80.3 Spectrophotometer: Shimadzu Scale: U 6 @ 23°C Table 7Iluminate C Photopic 12.035% 0.3159 0.3171 Red Yellow Green D65
Iluminate D65 12.003% Max% Min% TRANS 15.7237% 12.3030% 11.8168% 12.0032%Iluminate A 12.166% 18.0000 8.5000 TEST Pass Pass Pass
Iluminate C Scotopic 12.693% 0.0000 0.0000 X 12.15 1.32 12.27 Result MaxAverage Blue Light 8.705% Lum Trans: 12.035% Y 1.71 8.41 2.56 12.68 0.000 Pass 0.1Short W avelength 0.000% Z 0.02 2.72 13.59
UVA 0.000% Pass x 0.5903 0.2003 0.3183 0.000 Pass 0.010UVB 0.000% Pass y 0.4086 0.3878 0.3291
Spectral Transmittance Pass Chromaticity Pass Pass Pass
nm %T nm %T200 0.00 460 13.89205 0.00 470 16.76210 0.00 480 15.99215 0.00 490 14.62220 0.00 500 13.15225 0.00 510 12.01230 0.00 520 11.67235 0.00 530 11.37240 0.00 540 10.98245 0.00 550 11.00250 0.00 560 11.52255 0.00 570 11.95260 0.00 580 11.80265 0.00 590 11.38270 0.00 600 11.31275 0.00 610 11.85280 0.00 620 12.71290 0.00 630 13.55300 0.00 640 14.37310 0.00 650 15.81320 0.00 660 18.42330 0.00 670 22.70340 0.00 680 29.18350 0.00 690 36.41360 0.00 700 43.73370 0.00 710 50.58380 0.00 720 55.53390 0.00 730 58.94400 0.00 740 60.93410 1.50 750 61.63420 6.32 760 61.75430 9.01 770 61.68440 10.47 780 61.92450 9.32 790 62.57
GENERAL
Spectrophotometer: Shimadzu
RESULTS
Claim:
Pass
Spectacle
LeftZ-ESO081617-02-04
Near UV [T(NUV] =
Far UV [T(EUV)] =
0
10
20
30
40
50
60
70
80
90
100
280
300
320
340
360
380
400
420
440
460
480
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
Wavelength - nm
% T
rans
mitt
ance
0
0.2
0.4
0.6
0.8
1
200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380
Wavelength - nm
% T
rans
mitt
ance
Far UV Near UV
Page 15 of 28
LeftZ-ESO081617-02-04
Color Limit Regions
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8Values of x
Valu
es o
f yGreenRegion
Green
YellowRegion
Yellow
AverageDaylight
D65
Page 16 of 28
TRANS x y L 3 ANSI Z80.3 Spectrophotometer: Shimadzu Scale: U 6 @ 23°C Table 7Iluminate C Photopic 11.708% 0.3166 0.3176 Red Yellow Green D65
Iluminate D65 11.677% Max% Min% TRANS 15.4612% 11.9796% 11.4847% 11.6771%Iluminate A 11.845% 18.0000 8.5000 TEST Pass Pass Pass
Iluminate C Scotopic 12.323% 0.0000 0.0000 X 11.84 1.28 11.94 Result MaxAverage Blue Light 8.442% Lum Trans: 11.708% Y 1.68 8.19 2.49 12.34 0.000 Pass 0.1Short W avelength 0.000% Z 0.02 2.63 13.16
UVA 0.000% Pass x 0.5906 0.2005 0.3189 0.000 Pass 0.010UVB 0.000% Pass y 0.4083 0.3882 0.3296
Spectral Transmittance Pass Chromaticity Pass Pass Pass
nm %T nm %T200 0.00 460 13.55205 0.00 470 16.10210 0.00 480 15.52215 0.00 490 14.37220 0.00 500 12.80225 0.00 510 11.52230 0.00 520 11.24235 0.00 530 11.21240 0.00 540 10.81245 0.00 550 10.54250 0.00 560 10.97255 0.00 570 11.72260 0.00 580 11.81265 0.00 590 11.16270 0.00 600 10.76275 0.00 610 11.26280 0.00 620 12.40290 0.00 630 13.55300 0.00 640 14.35310 0.00 650 15.41320 0.00 660 17.61330 0.00 670 21.71340 0.00 680 28.50350 0.00 690 36.30360 0.00 700 44.16370 0.00 710 50.72380 0.00 720 54.80390 0.00 730 57.26400 0.00 740 58.82410 1.42 750 59.92420 6.10 760 60.94430 8.73 770 61.82440 10.02 780 62.49450 9.07 790 62.92
GENERAL
Spectrophotometer: Shimadzu
RESULTS
Claim:
Pass
Spectacle
RightZ-ESO081617-02-04
Near UV [T(NUV] =
Far UV [T(EUV)] =
0
10
20
30
40
50
60
70
80
90
100
280
300
320
340
360
380
400
420
440
460
480
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
Wavelength - nm
% T
rans
mitt
ance
0
0.2
0.4
0.6
0.8
1
200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380
Wavelength - nm
% T
rans
mitt
ance
Far UV Near UV
Page 17 of 28
RightZ-ESO081617-02-04
Color Limit Regions
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8Values of x
Valu
es o
f yGreenRegion
Green
YellowRegion
Yellow
AverageDaylight
D65
Page 18 of 28
Final Conclusion:
On August 16, 2017, COLTS Laboratories received Spectacles: Eagle from Importadores y Exportadores Solmaq SAS. From August 30, 2017 through September 15, 2017 COLTS Laboratories tested these Spectacles in accordance with ANSI Z87.1-2015.
Indoor/Outdoor Lens, Black Frame and Temples (U6L2)Product Description:
EagleANSI Z87.1-2015 High Impact Spectacles - Tint VariantZ-ESO081617-02-05Project ID(s):
Report of:of Model(s):
Project
September 15, 2017Paulo Barriga
Date:Attn:
Bogotá,
Importadores y Exportadores Solmaq SAS
Report To:
Report Summary
The Spectacles: Eagle (Indoor/Outdoor Lens, Black Frame and Temples (U6L2)) do comply with ANSI Z87.1-2015 for the test(s) performed for ANSI Z87.1-2015 High Impact Spectacles - Tint Variant.
COLTS Laboratories
702 Stevens AvenueOldsmar, FL 34677TEL: 727-725-2323FAX:727-725-8890Email:[email protected]:www.colts-laboratories.com A2LA Accredited Certificate # 1612.01
Carrera 30, número 15-30
Dale PayneTechnical Services ManagerVice-President & COO
Daryl Neely
COLTS LaboratoriesRespectfully submitted,
Please contact us should you have any questions concerning this report.
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 19 of 28
Protector lenses shall be free of:5.1.1Optical Qualitystriae, bubbles, waves and other visible defects which would impair the wearer's vision.
Acceptable Pass
All protectors shall bear the permanent and legible markings in specified locations as shown in Table 3. Markings for lens type and use applications shall be required only when claims for protection against the hazard or indicated use are made by the manufacturer.
Protector markings shall be placed in relatable proximity to each other on the product in the sequence specified below:
- Manufacturer's marks or logos - Designation of standard (Z87 or Z87-2, for prescription devices) - Individual claims of compliance - impact-rated marking (+) - lens type - use applications
Manufacturer's marks or logos are exempt from the proximity requirement if they are clearly present elsewhere on the product.
5.3Required Protector Markings (Spectacles)
Markings permanent, legible and in relatable proximity Not Assessed Not AssessedNot assessed per customer request
Markings representative of other standards shall not interfere with or be intermixed with the markings required by this standard.
Not Assessed Not Assessed
Not assessed per customer request Complete Device Markings Not Assessed Not Assessed
Sequence Correct Not Assessed Not AssessedMfg Mark or Logo Not Assessed Not AssessedZ87 Mark Not Assessed Not Assessed+ Mark Not Assessed Not AssessedH Mark (Coverage - small head sizes) Not Assessed Not AssessedLens Type (multiple claim sequence W,U,L,R,V,S) Not Assessed Not AssessedUse (multiple claim sequence D3,D4,D5) Not Assessed Not Assessed
Not assessed per customer request The complete device shall meet the protector acceptance criteria when impacted by a pointed projectile weighing a minimum of 500 g (17.6 oz) dropped from a height of at least 127 cm (50.0 in.).
6.2.2High Mass Impact
Left Eye Sample 1 Acceptable Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-05
Lab Temp (C): 23
Lab Rh: 49
Sample ID:Eagle
Indoor/Outdoor Lens, Black Frame and Temples (U6L2)
9/15/2017
Report of: ANSI Z87.1-2015 High Impact Spectacles - Tint Variant
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 20 of 28
The complete device shall meet the protector acceptance criteria when impacted by a pointed projectile weighing a minimum of 500 g (17.6 oz) dropped from a height of at least 127 cm (50.0 in.).
6.2.2High Mass Impact
Left Eye Sample 2 Acceptable Pass
Right Eye Sample 3 Acceptable Pass
Right Eye Sample 4 Acceptable PassThe complete device shall meet the protector acceptance criteria when impacted by a 6.35 mm (0.25 in) diameter steel ball traveling at 150 feet per second.
6.2.3High Velocity Impact (Spectacles)
Left Eye Center 151 fps Pass
Left Eye 30° 152 fps Pass
Right Eye Center 151 fps Pass
Right Eye 30° 151 fps Pass
One Side 90° at 10mm Above (H - 8mm) 150 fps Pass
Opposite Side 90° at 10mm Below (H - 8mm) 151 fps PassWhen tested in accordance with Section 9.2, plano, reader, magnifier and prescription lenses that are marked as special purpose filters shall meet the requirements of Table 10.Representative test lenses of plano power may be substituted for prescription, reader or magnifier lenses in this test.
7.2.1.1Special Purpose Filter Lenses - Transmission Requirements
Tinted Lenses (8% - 85%) Acceptable Pass
Left Eye 36.4% PassRight Eye 36.6% PassRatio (0.90 - 1.10) 0.995 Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-05
Lab Temp (C): 23
Lab Rh: 49
Sample ID:Eagle
Indoor/Outdoor Lens, Black Frame and Temples (U6L2)
9/15/2017
Report of: ANSI Z87.1-2015 High Impact Spectacles - Tint Variant
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 21 of 28
Final Conclusion:
On August 16, 2017, COLTS Laboratories received Spectacles: Eagle from Importadores y Exportadores Solmaq SAS. From August 30, 2017 through September 15, 2017 COLTS Laboratories tested these Spectacles in accordance with ANSI Z87.1-2015.
Indoor/Outdoor Lens, Black Frame and Temples (U6L2)Product Description:
EagleANSI Z87.1-2015 Optional Transmittance Attributes (U,L)Z-ESO081617-02-06Project ID(s):
Report of:of Model(s):
Project
September 15, 2017Paulo Barriga
Date:Attn:
Bogotá,
Importadores y Exportadores Solmaq SAS
Report To:
Report Summary
The Spectacles: Eagle (Indoor/Outdoor Lens, Black Frame and Temples (U6L2)) do comply with ANSI Z87.1-2015 for the test(s) performed for ANSI Z87.1-2015 Optional Transmittance Attributes (U,L).
COLTS Laboratories
702 Stevens AvenueOldsmar, FL 34677TEL: 727-725-2323FAX:727-725-8890Email:[email protected]:www.colts-laboratories.com A2LA Accredited Certificate # 1612.01
Carrera 30, número 15-30
Dale PayneTechnical Services ManagerVice-President & COO
Daryl Neely
COLTS LaboratoriesRespectfully submitted,
Please contact us should you have any questions concerning this report.
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 22 of 28
Optional transmittance characteristics of a protector are represented by a scale/shade number indicating its ability to filter optical radiation. They shall meet the requirements, including markings, of Tables 6, 7, 8 and 9, if claims of compliance are made. Special purpose filters shall meet the requirements of Table 10.
7Optical Radiation Protector Requirements
Transmittance Acceptable Pass
Markings Not Assessed Not AssessedNot assessed per customer request
When tested in accordance with Section 9.2, plano, reader, magnifier and prescription lenses that are marked as ultraviolet filter lenses shall comply with requirements of Table 7. Representative test lenses of plano power may be substituted for prescription, reader or magnifier lenses in this test.
7.2.1.1Ultraviolet Filter Lenses - Transmission Requirements
U.V. Far Acceptable Pass
Left Eye 0.000% PassRight Eye 0.000% Pass
U.V. Near Acceptable Pass
Left Eye 0.000% PassRight Eye 0.000% Pass
When tested in accordance with Section 9.2, plano, reader, magnifier and prescription lenses that are marked as visible light filter lenses shall comply with requirements of Table 9. Representative test lenses of plano power may be substituted for prescription, reader or magnifier lenses in this test.
7.2.1.1Visible Light Filter Lenses - Transmission Requirements
Visible Light Acceptable Pass
Left Eye 38.306% PassRight Eye 37.250% Pass
Visible light filters in the range of L1.3 through L3 shall also meet the transmittance requirements of Table 4 of ANSI Z80.3-2010, including traffic signal recognition and UV transmittance (high and prolonged exposure). Visible light filters in the range of L4 through L10 are too dark to be used for driving, but shall meet the UV transmittance (high and prolonged exposure) requirements of Table 4 of ANSI Z80.3-2010.
7.2.1.2Visible Light Filters
Traffic Signal Recognition - Color Limits and Chromaticity Coordinates
Acceptable Pass
Left Eye See charts PassRight Eye See charts Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-06
Lab Temp (C): 23
Lab Rh: 47
Sample ID:Eagle
Indoor/Outdoor Lens, Black Frame and Temples (U6L2)
9/15/2017
Report of: ANSI Z87.1-2015 Optional Transmittance Attributes (U,L)
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 23 of 28
Visible light filters in the range of L1.3 through L3 shall also meet the transmittance requirements of Table 4 of ANSI Z80.3-2010, including traffic signal recognition and UV transmittance (high and prolonged exposure). Visible light filters in the range of L4 through L10 are too dark to be used for driving, but shall meet the UV transmittance (high and prolonged exposure) requirements of Table 4 of ANSI Z80.3-2010.
7.2.1.2Visible Light Filters
Traffic Signal Recognition - Red Signal 8% Minimum Acceptable Pass
Left Eye 42.9950% PassRight Eye 42.7243% Pass
Traffic Signal Recognition - Yellow Signal 6% Minimum Acceptable Pass
Left Eye 40.2758% PassRight Eye 39.2755% Pass
Traffic Signal Recognition - Green Signal 6% Minimum Acceptable Pass
Left Eye 37.0539% PassRight Eye 35.9781% Pass
Mean UVB 1% Maximum Acceptable Pass
Left Eye 0.000% PassRight Eye 0.000% Pass
Mean UVA 0.5% Luminous Transmittance Maximum Acceptable Pass
Left Eye 0.000% PassRight Eye 0.000% Pass
Test ResultsRequirementParagraphTest/Property
Report To: Importadores y Exportadores Solmaq SASProject No: Z-ESO081617-02-06
Lab Temp (C): 23
Lab Rh: 47
Sample ID:Eagle
Indoor/Outdoor Lens, Black Frame and Temples (U6L2)
9/15/2017
Report of: ANSI Z87.1-2015 Optional Transmittance Attributes (U,L)
Report Date:A2LA Accredited Certificate # 1612.01
Acceptance
"The pages of this report (including attachments) shall not be reproduced, except in full, without written approval of COLTS Laboratories"
Page 24 of 28
TRANS x y L 2 ANSI Z80.3 Spectrophotometer: Shimadzu Scale: U 6 @ 23°C Table 7Iluminate C Photopic 38.306% 0.3357 0.3410 Red Yellow Green D65
Iluminate D65 38.276% Max% Min% TRANS 42.9950% 40.2758% 37.0539% 38.2762%Iluminate A 39.220% 43.0000 29.0000 TEST Pass Pass Pass
Iluminate C Scotopic 34.602% 0.0000 0.0000 X 38.47 4.13 38.70 Result MaxAverage Blue Light 21.837% Lum Trans: 38.306% Y 4.68 27.52 8.02 40.45 0.000 Pass 0.1Short W avelength 0.000% Z 0.08 6.79 35.28
UVA 0.000% Pass x 0.5823 0.2180 0.3382 0.000 Pass 0.010UVB 0.000% Pass y 0.4166 0.4236 0.3535
Spectral Transmittance Pass Chromaticity Pass Pass Pass
nm %T nm %T200 0.00 460 32.70205 0.00 470 33.17210 0.00 480 33.45215 0.00 490 34.13220 0.00 500 35.01225 0.00 510 35.48230 0.00 520 35.99235 0.00 530 36.84240 0.00 540 37.53245 0.00 550 37.83250 0.00 560 38.01255 0.00 570 38.59260 0.00 580 39.78265 0.00 590 40.93270 0.00 600 41.59275 0.00 610 41.64280 0.00 620 41.51290 0.00 630 41.78300 0.00 640 42.75310 0.00 650 44.25320 0.00 660 45.65330 0.00 670 46.48340 0.00 680 46.57350 0.00 690 46.19360 0.00 700 45.81370 0.00 710 45.85380 0.00 720 46.58390 0.00 730 47.80400 0.00 740 49.32410 1.73 750 50.63420 18.70 760 51.61430 28.75 770 51.91440 30.77 780 51.73450 31.61 790 51.27
GENERAL
Spectrophotometer: Shimadzu
RESULTS
Claim:
Pass
Spectacle
LeftZ-ESO081617-02-06
Near UV [T(NUV] =
Far UV [T(EUV)] =
0
10
20
30
40
50
60
70
80
90
100
280
300
320
340
360
380
400
420
440
460
480
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
Wavelength - nm
% T
rans
mitt
ance
0
0.2
0.4
0.6
0.8
1
200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380
Wavelength - nm
% T
rans
mitt
ance
Far UV Near UV
Page 25 of 28
LeftZ-ESO081617-02-06
Color Limit Regions
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8Values of x
Valu
es o
f yGreenRegion
Green
YellowRegion
Yellow
AverageDaylight
D65
Page 26 of 28
TRANS x y L 2 ANSI Z80.3 Spectrophotometer: Shimadzu Scale: U 6 @ 23°C Table 7Iluminate C Photopic 37.250% 0.3363 0.3415 Red Yellow Green D65
Iluminate D65 37.205% Max% Min% TRANS 42.7243% 39.2755% 35.9781% 37.2048%Iluminate A 38.148% 43.0000 29.0000 TEST Pass Pass Pass
Iluminate C Scotopic 33.575% 0.0000 0.0000 X 37.51 4.01 37.65 Result MaxAverage Blue Light 21.095% Lum Trans: 37.250% Y 4.65 26.84 7.79 39.32 0.000 Pass 0.1Short W avelength 0.000% Z 0.07 6.58 34.19
UVA 0.000% Pass x 0.5822 0.2182 0.3387 0.000 Pass 0.010UVB 0.000% Pass y 0.4166 0.4239 0.3537
Spectral Transmittance Pass Chromaticity Pass Pass Pass
nm %T nm %T200 0.00 460 32.46205 0.00 470 31.56210 0.00 480 31.51215 0.00 490 32.93220 0.00 500 34.73225 0.00 510 35.22230 0.00 520 34.82235 0.00 530 34.79240 0.00 540 35.70245 0.00 550 37.10250 0.00 560 38.19255 0.00 570 38.49260 0.00 580 38.35265 0.00 590 38.36270 0.00 600 39.02275 0.00 610 40.32280 0.00 620 41.72290 0.00 630 42.80300 0.00 640 43.21310 0.00 650 43.12320 0.00 660 42.86330 0.00 670 42.79340 0.00 680 43.23350 0.00 690 44.11360 0.00 700 45.40370 0.00 710 46.87380 0.00 720 48.16390 0.00 730 48.98400 0.00 740 49.25410 1.73 750 49.08420 18.55 760 48.65430 26.49 770 48.16440 29.23 780 47.87450 31.76 790 47.88
GENERAL
Spectrophotometer: Shimadzu
RESULTS
Claim:
Pass
Spectacle
RightZ-ESO081617-02-06
Near UV [T(NUV] =
Far UV [T(EUV)] =
0
10
20
30
40
50
60
70
80
90
100
280
300
320
340
360
380
400
420
440
460
480
500
520
540
560
580
600
620
640
660
680
700
720
740
760
780
Wavelength - nm
% T
rans
mitt
ance
0
0.2
0.4
0.6
0.8
1
200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370 380
Wavelength - nm
% T
rans
mitt
ance
Far UV Near UV
Page 27 of 28
RightZ-ESO081617-02-06
Color Limit Regions
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8Values of x
Valu
es o
f yGreenRegion
Green
YellowRegion
Yellow
AverageDaylight
D65
Page 28 of 28