1 EN 2010 - Honda France Manufacturing S.A.S. - Pôle 45 - Rue des Châtaigniers 45140 ORMES - FRANCE - All rights reserved 3RVK8700 0910 00X3R-VK8-7001 Printed in France OWNER’S MANUAL Original instructions HRX476C Lawn mowers 1 FOREWORD Dear Honda User, You have just purchased a Honda lawn mower and we thank you for your confidence in us. This manual has been written to familiarise you with your mower, to enable you to use it in the best possible conditions and to carry out its maintenance. Our aim is to make you benefit to the full from technological advances, from new equipment and materials and from our experience. This is why we regularly make improvements to our models. Thus, the specifications and information contained in this manual may be modified without prior notice and without obligation to update it. If you have a problem, or if you have any questions concerning the mower, contact your supplying dealer or approved Honda dealer. Keep this manual handy so you can consult it at any time. If you sell the mower be sure that the manual accompanies it. We recommend that you read the guarantee policy to fully understand your rights and responsibilities. The guarantee policy is a separate document provided by your dealer. No reproduction, even partial, may be made of this publication without prior written authorisation. SAFETY INSTRUCTIONS For your own safety and operating comfort, it is highly recommended that you read this manual in full. Pay attention to these symbols and their meaning: Indicates a high risk of severe personal injury or death if instructions are not followed. CAUTION: • Indicates a possibility of personel injury or equipment damage if instructions are not followed. NOTE: Source of usefull information. DESCRIPTION OF THE CODES USED IN THIS MANUAL The model of your machine is indicated on its "identification label", by a series of letters and figures (see page 3). CONTENTS Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety stickers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Identification of machine . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Preparations and checks before use . . . . . . . . . . . . . . . . . 4 Selecting the cutting mode . . . . . . . . . . . . . . . . . . . . . . . . . 6 Starting and stopping the engine . . . . . . . . . . . . . . . . . . . . 7 Operating hints and tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Useful Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Major Honda distributor addresses . . . . . . . . . . . . . . . . . 17 EC-Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . 18 HRX476C H Y E P K E V K E V Y E Hydrostatic drive Selfpropelled . . . . . . . . . . . . . . . . . Pushed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Self-propelled with variable speed transmission . . . . ● ● ● ● Blade brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotostop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ● ● ● ● Write down your machine's serial number here Write down your machine's model here
Transcript
1 EN
2010 - Honda France Manufacturing S.A.S. - Pôle 45 - Rue des Châtaigniers45140 ORMES - FRANCE - All rights reserved
3RVK8700 091000X3R-VK8-7001 Printed in France
OWNER’S MANUALOriginal instructions
HRX476CLawn mowers
1
FOREWORDDear Honda User,You have just purchased a Honda lawn mower and we thank youfor your confidence in us.This manual has been written to familiarise you with your mower, toenable you to use it in the best possible conditions and to carry outits maintenance.Our aim is to make you benefit to the full from technologicaladvances, from new equipment and materials and from ourexperience. This is why we regularly make improvements to ourmodels. Thus, the specifications and information contained in thismanual may be modified without prior notice and without obligationto update it.If you have a problem, or if you have any questions concerning themower, contact your supplying dealer or approved Honda dealer.Keep this manual handy so you can consult it at any time. If you sellthe mower be sure that the manual accompanies it.We recommend that you read the guarantee policy to fullyunderstand your rights and responsibilities. The guarantee policy isa separate document provided by your dealer.No reproduction, even partial, may be made of this publicationwithout prior written authorisation.
SAFETY INSTRUCTIONSFor your own safety and operating comfort, it is highlyrecommended that you read this manual in full.Pay attention to these symbols and their meaning:
Indicates a high risk of severe personal injury or death ifinstructions are not followed.
CAUTION:• Indicates a possibility of personel injury or equipment damage if
instructions are not followed.
NOTE: Source of usefull information.
DESCRIPTION OF THE CODES USED IN THIS MANUAL
The model of your machine is indicated on its "identification label",by a series of letters and figures (see page 3).
SAFETY INSTRUCTIONSFor your own safety and operating comfort, it is highlyrecommended that you read this manual in full.Pay attention to these symbols and their meaning:
Indicates a high risk of severe personal injury or death ifinstructions are not followed.CAUTION:• Indicates a possibility of personel injury or equipment damage if
instructions are not followed.
NOTE: Source of useful information.
This sign means that you must take care duringcertain operations. Refer to the safety instructionson the following pages, to the point(s) indicated inthe box.
TRAININGA1. Read the instructions carefully. Be familiar with the controls and the proper use
before using the equipment. Know how to stop the engine rapidly.A2. Use the mower for the purpose it is intended for, that is mowing and collecting
grass. Any other use could be dangerous or damage the equipment.A3. Never allow children or people unfamiliar with these instructions to use the lawn
mower. Local regulations may restrict the age of the operator.A4. Never mow when:
- People, especially children or pets are nearby.- User is under medication or has swallowed substances known to affect
judgement or reactions.A5. Keep in mind that the owner or user is responsible for accidents or hazards
occurring to other people or their property.
PREPARATIONB1. While mowing, always wear substantial footwear and long trousers.
Do not operate the equipment when barefoot or wearing sandals.B2. Thoroughly inspect the area where the equipment is to be used and remove all
objects which may be thrown by the machine (stones, branches, wires, bones,etc...).
B3. WARNING - Petrol is highly flammable.- Store fuel in containers specifically designed for this purpose.- Refuel outdoors only, before starting the engine and do not smoke while
refuelling or handling fuel.- Never remove the cap of the fuel tank or add petrol while the engine is running
or when the engine is hot.- If petrol is spilled, do not attempt to start the engine but move the machine away
from the area of spillage and avoid creating any source of ignition until petrolvapours are dissipated.
- Replace all fuel tanks and container caps securely.- Before tipping the lawn mower to maintain the blade or drain oil, remove fuel
from tank.B4. Replace faulty silencers.B5. Before use, always visually inspect the machine, especially to see that the blades,
blade bolts and cutter assembly are not worn or damaged. Replace worn or damaged blades and bolts in sets to preserve balance.
OPERATIONC1. Do not operate the engine in a confined space where dangerous carbon monoxide
fumes can collect.C2. Mow only in daylight or in good artificial light.C3. Avoid operating the equipment in wet grass, where possible.
C4. While mowing, always keep the safety distance to the blade, which is provided bythe handle length.
C5. Walk, never run. Do not let yourself be pulled by the mower.C6. Always be sure of your footing on slopes. Mow across the face of slopes, never
up and down.C7. Exercise extreme caution when changing direction on slopes.C8. Do not mow slopes of more than 20°.C9. Use extreme caution when pulling the lawn mower towards you.
C10. Stop the blade if the lawn mower has to be tilted for transportation when crossingsurfaces other than grass, and when transporting the lawn mower to and from thearea to be mowed.
C11. Never operate the lawn mower with defective guards or housings, or withoutsafety devices such as deflectors and/ or grass catchers.
C12. Do not change the engine governor settings or overspeed the engine.C13. Disengage all blade (models equipped with Rotostop) and drive clutches
(self-propelled models) before starting the engine.C14. Start the engine carefully according to instructions and with feet well away from
the blade.C15. Do not tilt the lawn mower when starting the engine.
Start the mower on a level surface, free of high grass or obstacle.C16. Keep hands and feet away from the rotating parts.
Do not start the engine when standing in front of the discharge opening.C17. Never pick up or carry a lawn mower while the engine is running.C18. Stop the engine and disconnect the spark plug cap in the following cases:
- Before any operation under the cutter housing or the discharge tunnel.- Before checking, cleaning or working on the lawn mower.- After striking a foreign object. Inspect the lawn mower for damage and make
repairs before restarting and operating the lawn mower again.- If lawn mower starts to vibrate abnormally. Check immediately the cause of the
vibration and perform the necessary repair.C19. Stop the engine in the following cases:
- Whenever you leave the lawn mower unattended.- Before refuelling.
C20. Stop the blade (models equipped with Rotostop) or the engine in the followingcases:- When installing or removing the grass bag.- Before adjusting the cutting height.
C21. Reduce the throttle setting during engine shut-down. Close the fuel shut-off valveby turning the fuel shut-off valve.
C22. Using any attachments other than those recommended in this manual may causedamage to your lawn mower, and such damage will not be covered by yourguarantee.
MAINTENANCE AND STORAGED1. Keep all nuts, bolts and screws tight to be sure the equipment is in safe working
condition. Regular maintenance is an essential aid to user’s safety and retaininga high level of performance.
D2. Never store the equipment with petrol in the tank inside a building when vapoursmay reach an open flame, spark or high temperature source.
D3. Allow the engine to cool before storing in any enclosure.D4. To reduce the fire hazard, keep the mower, especially the engine and silencer, the
petrol storage area as well, free of grass, leaves, or excessive grease. Do not leave containers of grass cuttings in or near a building.
D5. If the fuel tank has to be drained, this should be done outdoors, with a cold engine.D6. Check the grass collecting system frequently for wear or deterioration.D7. Do not use the machine with worn or damaged parts.
Parts must be replaced, not repaired. Replace worn or damaged parts with Hondagenuine parts. Blades must always bear the mark Honda and the reference number.Non equivalent quality parts may damage the machine and be prejudicial to yoursafety.
D8. Wear thick gloves when removing or installing the blade or when cleaning thecutter housing. When tightening or loosening the blade screws, use a wooden block to preventthe blade from rotating.
D9. Always make sure the correct balance of the blade when sharpening.
SAFETY
3 EN
SAFETY STICKERSYour lawn mower must be used with care. Therefore, decals have been placed on the machine, to remind you pictorially of main precautions to take during use. Their meaning is explained below.These decals are considered as a part of the mower. Should one become detached or unreadable, contact your Honda dealer for its replacement.We also recommend that you read the safety advice carefully (see page 2).
IDENTIFICATION OF MACHINE
GENERAL DESCRIPTION
EQUIPMENT IDENTIFICATION
[1] WARNING: Read the owner's manual before using the mower.[2] Risk of projections: Keep third persons away from the area during use.[3] Risk of cuts. Rotating blade: Do not put hands or feet inside the blade
enclosure. Disconnect the spark plug cap before performing any operation of maintenance or repairs.
[4] Do not operate without either discharge guard or grass catcher in place.[5] The muffler becomes very hot during operation and remains hot for a while
after stopping the engine.[6] The engine emits toxic carbon monoxide. Do not run in an enclosed area.[7] Petrol is highly flammable. Stop the engine before refueling.
[8] Acoustic power level according to the directives 2000/14/EC, 2005/88/EC
[9] Conformity mark, according to the directives 2006/42/EC, 2000/14/EC, 2005/88/EC, 2004/108/EC
[10] Russian conformity mark[11] Nominal power in kilowatt[12] Recommended engine speed in rpm[13] Mass in kilograms[14] Year of manufacture[15] Serial number[16] Model - Type[17] Name and adress of the manufacturer
[2]
[1]
[5]
[4]
[3]
[1] [6] [7]
[A] Honda France Manufacturing S.A.S.Rue des Châtaigniers - Pôle 4545140 Ormes - France
[8] [9]
[17]
[10] [11] [12]
[16][15][14]
[13]
CONTROLS FUNCTIONS[18] Handle[19] Blade clutch lever (Rotostop) (*) . . Couple and stops the blade[20] Lever for adjusting the
cuting height . . . . . . . . . . . . . . . . . Selects the desired cutting height[21] Folding knob / adjusting the handle Allows you to adjust the height of the
handle or to fold the handle[22] Blade clutch lever unlocking knob (*) Activates blade clutch lever[23] Variable speed clutch lever (*) . . . Controls the maximum drive speed[24] Drive clutch lever (*) . . . . . . . . . . . Transmission control which drives
the rear wheels[25] Blade brake lever (*) . . . . . . . . . . . Stops the blade rotation and the
To carry out this seriesof checks, place themower on stable andlevel ground with engine stopped andspark plug [1] capremoved.
ASSEMBLY OF THE HANDLE1. Turn the folding/handle adjustment knobs [2] a quarter turn to
unlocked position [3].2. Unfold the handle so that the folding knob axes line up with the
top, intermediate or bottom holes [4], depending on the handle height required.
3. Put the knobs back to locked position [5].
Ensure that the clamping rings for the cables on the handle are positioned correctly. To assemble the grass bag, please refer to page 12.
CHECKING THE GRASS BAG
Before use, ensure that the bag closing device is correctly locked (discharge guard).Even in normal use, the grass bag tends to wear. Regularly check that it is not frayed or torn. A worn out bag must be replaced. Replace a damaged bag by a Honda bag only.
Bag removal:1. Stop the engine.2. Raise discharge
guard [6], grasp handle [7] and remove bag [8] while keeping it in an upright position.
Bag fitting:1. Raise the discharge
guard and hook the front of the bag on the mower’s attachment lugs [9].
NOTE: The lawn mower operates like a vacuum cleaner; it blows air into the grass bag sucking up the grass cuttings. Empty the grass bag before it is full to help emptying and minimising the dropping of grass cuttings. Bagging performance will diminish after the bag becomes about 90 % full.
CHECKING FUEL LEVEL
Do not fill the fuel tank up to the brim (There must be no fuel in the filler neck). When filling is completed, ensure that the tank filler cap is screwed fully on.Avoid getting fuel on the skin repeatedly or for long periods and avoid breathing fuel vapours. Keep fuel away from children.
CAUTION:• Ensure that you use
containers or drums specifically designed for hydrocarbons [10].
• Never use a petrol-oil mixture.
• Only use unleaded petrol 95 or 98.
• Do not let dirt, clippings, etc. get into the tank.
• Do not use dirty or contaminated fuel (water, dust, ...), or fuel which is too old. The quality of unleaded petrol deteriorates with time. Do not keep fuel for more than one month (see page 14).
To check the fuel level:1. Remove filler cap [11] and check fuel level.2. Fill [12] tank if level is low. The maximum level is reached when
the fuel is opposite mark [13].3. Screw filler cap [11] fully on after filling.
NOTE: Fuel substitute products are not recommended. These may damage fuel system components.
SAFETY B3
[1]
[3] [5]
[2] [2]
[4]
SAFETY D6C20
C11
[7]
[8]
[6][9]
[10]
[11]
[13]
[12]
5 EN
FUEL CONTAINING ALCOHOLIf you intend to use fuel with alcohol, ensure that its octane number is at least as high as that recommended by Honda (86). There are two types of fuel/alcohol mixtures: one contains ethanol and the other methanol.Do not use mixtures containing more than 10 % ethanol, or fuel containing methanol (methyl or wood alcohol), which do not contain cosolvents, or corrosion inhibitors for methanol.In the case of a mixture containing methanol with addition of cosolvents and corrosion inhibitors, limit the proportion to 5 % of methanol.NOTE: The guarantee does not cover damage caused to the fuel system or engine performance problems resulting from the use of fuel containing alcohol. Honda does not give its approval to the use of fuels containing methyl alcohol since their suitability is not yet proven.
CHECKING THE AIR CLEANERCAUTION:• Never run the engine without the air cleaner fitted since this could
cause premature engine wear.To check the condition of the air cleaner:1. Press the latch tabs [1]
on the top of the air cleaner cover and remove the cover [2].
2. Check the cleanliness of filter element [3].If the element is dirty, follow the cleaning procedure (see Maintenance chapter).
3. Reinstall the filter [3] and air cleaner cover [2].
CHECKING BLADE CONDITIONCAUTION:• Do not tilt the mower with the
carburetor facing down; this will make the mower difficult to start later, due to engine oil contaminating the air cleaner.
To check blade condition:1. Stop the engine.2. Pull off the spark plug cap.3. Tilt the mower to the right so the
fuel cap is up [4].• Check if the blade is showing
signs of wear. For your information, it is necessary to replace the blade when the recesses join together, or when a crack appears.
• Check that blade bolts are tight (see Maintenance chapter).• To replace or remove the blade, refer to the procedure
described in the Maintenance chapter.
Never operate the mower with a worn, damaged, split or dented blade. A piece of blade which breaks off and is thrown outwards can cause serious bodily injuries.
NOTE: Blade wear is increased when the mower is used on sandy soils. Inspect the blade more often when the mower is used in these conditions.
ADJUSTING CUTTING HEIGHTTo change the cutting height:1. Stop the engine.2. Keep the unlocking knob [5] pressed and raise or lower the
lawnmower with the adjustment handle [6]. A height indicator [7] is near the front left wheel.
The cutting height settings are approximate values, the actual height of the cut grass varies with the lawn and ground condition. To choose the cutting height, check how the lawn looks after mowing a small area and adjust the cutting height where necessary.
NOTE:• Do not cut more than 1/3 of
the initial height of the grass in one passage as brown spots will appear. The cut will be cleaner and this will limit the possibility of blade and chute blackage.
• If the lawn is too high, mow at the maximum permissible height of the mower. Mow the lawn again 2 or 3 days later.
• The depth of the roots is proportional to the height of the grass cuttings: the shorter the cut, the shallower the roots.
• Choose a cutting height suited to the use of the lawn: leisure, sport: 5 cm or more, ornamental: 1 to 3 cm.
• Only some species of lawn can endure short cuts. If a lawn is cut too short, it is fragile and susceptible to dryness. Please ask the advice of a specialist.
NORMAL BENT
EXCESSIVELY WORN CRACKED
[2]
[3]
[1]
SAFETY D8D1C18
B5B3
[4]
15 mmMax.
SAFETY C20
[5]
[7]
[6]
[7]
1/3 Max
1 25 2 34 3 43 4 52 5 61 6 70 7 79
Positions Height (mm)
6 EN
CHECKING ENGINE OIL LEVELCAUTION:• The engine oil is an essential element which affects the
performance and lifetime of the engine.• The engine may be seriously damaged if run with insufficient oil.
We recommend the use of Honda 4-stroke oil or an equivalent quality engine oil which is highly detergent. Oil viscosity must be appropriate for the average temperature in the zone where the mower is to be used.
Types of oil [1] adapted to the ambient temperature [2].
To check engine oil level:1. Put the lawn mower on
flat, even ground.2. Remove the oil filler cap
and wipe the dipstick [3].3. Replace the dipstick in
the filler neck but do not screw it down.
4. Check the level of the oil left on the dipstick. If the level is near the low level mark [4], add the recommended oil up to the high level mark [5].
5. Screw filler cap.
SELECTING THE CUTTING MODEADJUSTING THE VARIABLE MULCHING CONTROLHYE, VYE types:1. Release the blade clutch lever.PKE, VKE types:1. Release the blade brake lever.2. Turn the variable mulching control knob to one of the 5 positions
to obtain the required mulching and ejection rate.
- Grass collection position [7]: all the grass cuttings are ejected at the back of the lawn mower, the grass cuttings are not mulched.
- Mulching position [8]: the grass is no longer collected in the grass bag, but is finely cut and deposited on the lawn. The grass cuttings chopped up in this way decompose and form a natural compost which can produce a quarter of the annual fertilisation requirement of your lawn.
3. To choose the position best adapted to your requirements, carry out a test. Install the grass bag and start to mow in collection position [7]. Check the effect on the lawn. Turn the knob [6] one notch to the right. Turning the knob turned towards Mulching position [8] increases the quantity of grass ground and deposited on the lawn. Turn the control knob [6] until you obtain the required results.
NOTE: • Mulching is a natural fertilisation technique. The grass is no
longer collected in the grass bag, but is finely cut and deposited on the lawn.
• In addition to its fertilising role, mulching protects the cut, limits evaporation of water during hot periods and relieves you of the task of collecting the grass.
REAR EJECTIONIf you do not want to collect the cut grass, the mower can be used without the grass bag. In this case, the grass ejected is guided to the ground by the discharge guard. The quantity ejected varies depending on the position of the variable mulching control knob:
- maximal in position [7],- zero in position [8].
[1]
[2]
SAE :
-20 -10 0 10 20 30 40°C
5W30 - 10W30
30
0 20 40 60 80 100°F
[3]
[4][5]
[7] [8]
[6]
[8][7]
7 EN
STARTING AND STOPPING THE ENGINESTARTING THE ENGINECAUTION:• Do not start the engine with the blade clutch lever or the drive
clutch lever engaged.
All models:1. Open the fuel cock [1].2. Place the throttle lever [2] in
"FAST" position [A].
PKE, VKE types:3. Keep the blade brake lever
held [3] firmly against the handle when starting the engine.
All models:4. Pull the starter [4] slowly until a
resistance is felt; then pull sharply.
NOTE: • Do not let the starter spring back
suddenly on its own; guide it back slowly.
• To adjust the engine speed when the mower is running, the throttle lever can be set anywhere between the "FAST" position [A] and "SLOW" position [B] positions. However, the best results are obtained in the "FAST" position [A].
HYE, VYE types:The engine may stall if the lever is in the "SLOW" position [B] when the blade clutch is engaged.To facilitate starting, place the mower on a flat surface where the grass is not long.
STOPPING THE ENGINEHYE, VYE types:1. Move the throttle lever to the
"STOP" position [C].PKE, VKE types:1. Move the throttle lever to the
"SLOW" position [B].2. Release the blade brake lever.All models:3. Turn the fuel cock "STOP" [5].
FLOODED ENGINEIf the engine still refuses to start after several pulls on the starter, the engine may be flooded.To clear a flooded engine:1. Place the throttle lever in "STOP" position [C] (HYE, VYE types).2. Remove and dry the spark plug. When refitting the spark plug,
screw it up until it is finger tight and correctly seated. Then using the plug spanner, tighten it an additional 1/8 to 1/4 turn so that the washer is correctly compressed.
3. Next, place the throttle lever in "FAST" position [A] and repeat the operations previously mentionned under the heading "Starting the engine".
OPERATING HINTS AND TIPSUSING THE MOWER AT HIGH ALTITUDESAt high altitudes, the standard fuel/air mixture in the carburetor is much too rich: this will reduce performance and increase fuel consumption.It is possible to improve the high altitude performance by fitting the carburetor with a smaller diameter jet and by adjusting the pilot screw. If you use your mower at an altitude of more than 1500 meters above sea level, we recommend that you have these modifications made by your approved Honda dealer.Even with the appropriate modifications made to the carburetor, engine power will be reduced by about 3.5 % for every 300 meters of altitude. However, the altitude will have a much greater effect on power if these modifications are not carried out.
CAUTION:• Running the mower at an altitude less than that for which the
carburetor is adjusted may cause overheating and seriously damage the engine, due to the gas/air mixture being far too weak.
Take special care when mowing on uneven or irregular ground.The mower may tip over, thus uncovering the blade; also, the blade may throw out objects which were previously hidden.Keep the four wheels firmly on the ground.Control the direction of the mower using the handle and not byexercing pressure on the blade casing with your foot.CAUTION:• When mowing around an obstacle, be careful that the blade does
not hit it. Never push the mower directly over an object.• When mowing an uneven area, do not let yourself be pulled along
by the mower. Hold the handle firmly and control its movements.
NOTE: If the mower’s speed becomes too slow when mowing on a slope, move the shift lever slightly towards the "FAST" position.
[A] [B] [C]FAST
For restarting a hot engine
and for mowing.
SLOWSelects engineidling speed.
STOPStops engine
(Rotostop models).
SAFETY A1
[A]
[2]
[1]
STOP
SLOW
FAST
[A]
[2]
[4]
[3]
[5] [6] WRONG [7] RIGHT
SAFETY C8C7
C6
[6]
[7]
8 EN
MOWING PROCEDURE
Read the safety instructions before starting to mow.
HYE type:
Always release the blade clutch lever and the drive clutch lever before starting the engine. Starting is more difficult when the blade is engaged. If the clutch is engaged, the mower will move when the engine is started.
1. Select the suitable forward speed thanks to the shift lever [1].
2. Engage the blade:- Press the yellow button [2]
located on the top of the blade clutch lever [3], and at the same time push it quickly and hold it against the handle.
3. Engage mower forward drive when the motor has picked up speed:- The drive clutch lever [4] acts
as a variable speed control according to its squezzed position. It makes the speed vary between zero and the maximal speed preset with the shift lever. The maximum speed can be reached when both levers [3] and [4] are pushed forward completely. The greater the height of the grass to be cut, the more it is necessary to reduce the drive speed of the machine. This will prevent overloading the engine and improve the quality of the cut.
4. To stop the mower moving forward:- Release the drive clutch lever [4].
5. To stop the blade rotating:- Release the blade clutch lever [3].
NOTE: It is possible to refrain from using the forward drive while mowing in areas with a narrow surface.The drive clutch can be used to move the mower without engaging the blade clutch (lanes, borders, etc.).
CAUTION:• Move the blade clutch lever quickly from one end of its travel to
the other, so that the blade is always either fully engaged or fully disengaged. This is to avoid stalling the engine and increases the service life of the blade control mechanism.
PKE type:
NOTE: Releasing the blade brake lever [5] stops the blade rotating and stops the engine.
VKE type:1. Engage mower forward
drive [7] when the motor has picked up speed.- Push the Smart Drive [6]
slowly make the mower move forward.
- The drive speed increases depending on the pressure exerted on the Smart Drive.
- Apply only the pressure necessary to obtain the required speed. At a given position, the lawn mower speed varies according to several factors, such as the terrain, grass height, slope and weight of the grass bag. The Smart Drive is designed to allow you to maintain the desired drive speed under constantly changing grass cutting conditions.
2. To stop the mower moving forward:- Release the Smart Drive lever [6].
3. To stop the blade rotating:- Release the blade clutch lever [7].
NOTE: Releasing the blade brake lever stops the blade rotating and stops the engine.
VYE type:
Always release the blade clutch lever and the drive clutch lever before starting the engine. Starting is more difficult when the blade is engaged. If the clutch is engaged, the mower will move when the engine is started.
1. Engage the blade:- Press the unlocking
knob [8] and keep it pressed.
- Pull the blade clutch lever towards you [9].
- Release the unlocking knob [8] when the blades are engaged.
2. Engage mower forward drive when the motor has picked up speed:- Push the Smart Drive [10]
slowly make the mower move forward.
- The drive speed increases depending on the pressure exerted on the Smart Drive.
- Apply only the pressure necessary to obtain the required speed. At a given position, the lawn mower speed varies according to several factors, such as the terrain, grass height, slope and weight of the grass bag. The Smart Drive is designed to allow you to maintain the desired drive speed under constantly changing grass cutting conditions.
3. To stop the mower moving forward:- Release the Smart Drive lever [10].
4. To stop the blade rotating:- Release the blade clutch lever [11].
NOTE: It is possible to refrain from using the forward drive while mowing in areas with a narrow surface.Likewise, the drive clutch can be used to move the mower without engaging the blade clutch (lanes, borders, etc.).
SAFETY C8C7
C6
SAFETY
[1]
[3]
[4]
[2]
[5]
[7]
[6]
SMART DRIVEAdjustable
[8]
[9]
[10]
[8][11]
SMART DRIVEAdjustable
9 EN
CAUTION:• Move the blade clutch lever quickly from one end of its travel to
the other, so that the blade is always either fully engaged or fully disengaged. This is to avoid stalling the engine and increases the service life of the blade control mechanism.
NOTE:• Mowing frequency: once a week for a
lawn intended for leisure purposes, twice a week for an ornamental lawn.
• If possible, mow the lawn in the afternoon or evening before sprinkling, as the grass must be dry. If dust levels are too high, mow the lawn when the grass is dry, but the ground is still damp.
• Choose a cutting height adapted to the terrain (see page 5).
• For a regular cut, you should overlap the part that has already been cut by a few centimetres [1], and increase this overlap zone if the cutting height is high.
• To achieve maximum efficiency, follow the suggested path.• If your terrain does not have a regular shape or involves several
obstacles, divide it into internal parcels which you can mow in the recommended direction.
[2] With collection: turn in a clockwise direction to achieve the maximum efficiency.
[3] With the mulching kit (optional, page 15): turn in an anti-clockwise direction.
EMPTYING THE GRASS BAGWhen the grass bag becomes too full, grass collection is no longer efficient (the sound of the mower changes and the bag is no longer puffed up by the air from the blade).
HYE, VYE types:1. Release the blade clutch lever.PKE, VKE types:1. Release the blade brake lever.2. Remove the grass bag
(see page 4).3. Empty the bag:
• Hold the bag by the metal handle [4].
• Grasp handle [5] and shake the bag to remove the grass.
CAUTION:• To reduce the fire risk, never leave grass cuttings or leaves in the
grass bag, or in or near buildings. Decomposing grass cuttings matter causes a high temperature rise.
Before use, check that the bag closing device is correctly positioned (discharge guard).
MAINTENANCERegular maintenance is the guarantee of a long lifetime for your mower.
To avoid the mower starting accidentally, pull off the spark plug cap [6] before carrying out maintenance work.
CAUTION:• The engine and the muffler reach temperatures high enough to
cause burns and start fires if flammable materials are to be found nearby.
• Allow the engine to cool down for 15 minutes before carrying out maintenance operations.
NOTE: To assure a longer lifetime and more efficient operation, the underside of the mower must be kept clean and free of grass debris by cleaning with a brush and scraper. After use the mower must be cleaned thoroughly before being stored.
AIR CLEANER MAINTENANCEA dirty air cleaner will reduce the flow of air to the carburetor. To prevent the carburetor operating inefficiently, the air cleaner must be regularly maintained.
Never clean the air cleaner element using gas or flammable solvents; this could cause a fire or an explosion.
1. Press the latch tabs [7] on the top of the air cleaner cover, and remove the cover [9].
2. Inspect air filter [8] and replace it if it is damaged.
3. Tap the filter several times on a hard surface to remove dirt or blow compressed air (not exceeding 2.1 kgf/cm2, 30 psi) through the filter from the clean side that faces the engine.
NOTE: The filtering element [8] must be dry in order to work correctly. Do not soak with oil.
4. Wipe dirt from the inside of the air cleaner cover [9] and clean case, using a moist rag.
NOTE: Be careful to prevent dirt from entering the air duct [10] that leads to the carburetor.
5. Reinstall the filter [8] and air cleaner cover [9].
[1]
[3][2]
SAFETY C11
[5]
[4]
SAFETY D8D7C18
C1B3
[6]
[9]
[8][10]
[7]
10 EN
ENGINE OIL CHANGEDrain the oil while the engine is still hot, so that the oil drains quickly and completely.CAUTION:• Used engine oil can cause skin cancer if it remains in contact with
the skin for long periods.Although this is highly unlikely unless you handle used oil every day, we recommend that you wash your hands thoroughly with soap and water each time you handle used engine oil.
1. Tip the mower on its side.
2. Place a receptacle [1] under the casing filler tube hole. And rock the mower on the right side.
3. Remove the oil filler cap [2].
4. Return the mower to the upright position on its wheels when the casing is completely empty.
5. Fill up [3] to "high level" [4] using the recommended oil (see page 6).
6. Screw the filler cap fully on to avoid the risk of leaks.
NOTE: The used engine oil must be disposed of in a manner which respects the environment.We recommend that you take it to a service station which will ensure that it is recycled. Never dispose of used engine oil in dustbins or pour it away on the ground, in the gutter or down the drains.
CHECKING THE SPARK PLUG
Recommended plugs: NGK - BPR5ESCAUTION:• Use only recommended spark plugs. Using spark plugs with
inappropriate temperature ranges may damage the engine.
If the engine has just been run, do not touch the muffler and the spark plug which will still be very hot.
1. Pull off spark plug cap [6] and remove spark plug [7] using a plug spanner [8].
2. Carefully inspect the spark plug. Replace the plug if there are a lot of deposits or if the insulator is cracked or broken.
3. Measure the plug gap using a set of feeler gauges; the gap must be between 0.7 and 0.8 mm. If adjustment is necessary, carefully bend the side electrode.
4. Check that the sealing washer is in good condition; then screw the plug down by hand until finger tight and correctly seated.
5. Using a plug spanner, give an additional 1/2 turn for a new spark plug, to compress the washer. If you refit the same plug, just 1/8 to 1/4 turn will do from the finger tight position.
6. Refit the spark plug cap.
CAUTION:• The spark plug must be correctly tightened. A plug incorrectly
screwed down can become very hot and damage the engine.
MAINTENANCE OF SPARKARRESTER (OPTIONAL PART)
(In Europe and other countries where the machinery directive 2006/42/EC is enforced, this cleaning should be done by your servicing dealer).
If the mower has just been run, the silencer will still be very hot. Allow it to cool down before carrying out this operation.In some regions, it is prohibited to operate an engine without a spark arrester.
1. Remove the three flange bolts [9] from the muffler protector [10] and remove the muffler protector.
2. Remove the two tapping screws [11] from the spark arrester [12] and remove the spark arrester from the muffler.
3. Check the carbon deposits around the exhaust port and spark arrester. Clean if necessary.
4. Replace the spark arrester if there are any breaks or tears.
5. Install the spark arrester [12] and muffler protector [10] in the reverse order of removal.
SAFETY D8C18
[5][4]
[3]
[2]
[1]
0.7 - 0.8 mm
[7]
[8]
[6]
SAFETY C18
[12]
[11]
[10][9]
[12]
11 EN
CARBURETOR ADJUSTMENTCAUTION:• It is recommended to ask your Honda dealer for adjustment.
Specified idle speed: 1 700 ± 150 rpm
Operating speed: 2 800 rpm
BLADE BRAKE CABLE ADJUSTMENT
PKE type:1. Stop the engine and disconnect the spark plug cap.2. Release the blade brake lever [1] and verify that there is a strong
resistance when pulling on the recoil starter.
If not:3. Measure clearance [2] at the
tip of the lever [1] (30 to 35 mm clearance).
4. If adjustment is necessary, loosen the lock nuts [3] and adjust as required. Tighten the lock nuts and check the clearance again.
5. Start the engine and release the blade brake lever. Check that the blade and the engine stop when the lever is released. If not, take the mower to an approved Honda dealer.
SHIFT CABLE ADJUSTMENT
HYE type: Measure the free play [4] on the side of lever [5] as shown.1. Place the gear stick in the fastest position and loosen the
locknuts [6].2. Relax or tighten the cable as necessary so that a free play of 1
to 5 mm is achieved.3. Retighten the locknuts [6] and recheck the free play [4].4. Start the engine in the open air and operate the clutch lever.
Check that the clutch engages and disengages correctly.
VYE type:Perform this procedure with the wheels on a level surface.1. Loosen the Smart Drive clutch cable lock nut [8].2. Start the engine.3. Without engaging the Smart Drive grip, turn the clutch cable
adjuster [7] in the "MOVE" [A] direction until the lawn mower just begins to move forward.
4. Turn the clutch cable adjuster 1 ~ 2 turns in the "STOP" [B] direction.
5. Tighten the clutch cable lock nut.6. Check the operation of the Smart Drive system.
All models:
NOTE: If the clutch does not engage correctly even when the cable is correctly adjusted, the system may need to be repaired. Take the mower to an approved Honda dealer.
BLADE FITTING AND REMOVAL
BLADE REMOVAL1. Place the throttle lever in
"STOP" position (Rotostop drive models).
2. Turn the fuel valve "OFF" and disconnect the spark plug cap from the spark plug.
3. Tilt the mower so that the carburetor faces upwards [9].
4. Use a 14 mm socket wrench and remove the two blade bolts [10] and special washers [11] from the blade [14] control assembly.Use a wooden block to prevent the blades from turning when removing the bolts.
5. Remove the upper [13] and lower blades [12].
SAFETY C12C1
+ 0- 100
[1]
[2]
[3]
[3]
[4]
[5]
[6] [6]
[B][A]
[7]
[8]
SAFETY D9D8D7
C18B3
[9]
[14] [11] [10]
[13] [12]
12 EN
BLADE INSTALLATION1. Clean dirt and grass from around the blade mounting area.2. Install both blades [3] and [4] using the two blade bolts [1] and
special washers [2] as shown. Fit the special washers with their convex side, marked "OUT", facing the bolts.The blade bolts are specially designed for this application and must not be replaced with other bolts.
3. Tighten the blade bolts with a torque wrench [5]. Use a wooden block [6] to prevent the blades from turning.
Blade bolt torque: 49 ~ 59 Nm
CAUTION:• If you do not have a torque wrench, ask your approved Honda
mower dealer to tighten the blade bolts for you before you use the mower.
• If the blade bolts are too tight or too slack, they may break or unscrew.
Operating this mower with only one blade will result in an improperly seated blade that can be thrown from the mower and seriously hurt or kill someone.Always install both blades as a set.
NOTE: Never tip the mower so that the carburetor faces down; this will make starting difficult.
BLADE REPLACEMENT
CAUTION:• Blade balance is critical to proper mower performance. Replace
any blade that is damaged or out of balance.• Use only genuine Honda replacement blades.
BLADE SHARPENING1. Sharpen the blade cutting edges with a file. File the top side
only. Maintain the original bevel for a fine cutting edge. File both ends evenly to maintain blade balance.
2. After sharpening, test the blade’s balance using a screwdriver as shown. If either side dips slightly below the horizontal, file that side. Replace the blade if it dips excessively.
CAUTION:• To avoid weakening the blade, causing it to become unbalanced
or getting a bad quality of cut, the blade should be sharpened by competent personnel at your Honda dealer’s.
GRASS BAG CLEANING AND REPLACEMENTBAG CLEANINGCAUTION:• Washing with a high pressure water or
steam jet will damage the bag.• Blocked mesh will prevent the grass
from entering the bag.• To clean the bag, we recommend
washing it using a water jet directed from the outside to the inside of the bag. The bag must be completely dry before being used again. If the bag is damp, it will become clogged very quickly.
Objects struck by the blade may be thrown through a torn or damaged grass bag.Objects thrown out by the blade can cause serious injuries. Always replace a torn or damaged grass bag.
BAG REPLACEMENTThe grass bag tends to wear even in normal conditions of use. Regularly check that it is not frayed or torn. Replace a damaged bag only by a genuine Honda replacement bag.
1. Detach the plastic edges [7] of the worn bag [9] and remove the bag’s frame [8].
2. Insert the frame into the new bag and fit the plastic edges [7] to the frame.
[6]
[5]
[2] [1]
[3][4]
"OUT"
"OUT"
[3]
[1]
[2]
[4]
15 mmMax.
7 mmMax.
SAFETY D6C11
[8][7] [9]
[7]
13 EN
MAINTENANCE SCHEDULE
(1) Increase cleaning frequency when mower is used in dusty areas.(2) Maintenance of these points must be carried out by a Honda dealer.(3) HYE, VYE types(4) PKE, VKE types(5) HYE, VKE, VYE types(6) In Europe and other countries where the machinery directive 2006/42/EC is
enforced, this cleaning should be done by your servicing dealer.
TROUBLESHOOTINGENGINE WILL NOT START
LOSS OF POWER
MOWING AND BAGGING PROBLEMS
VIBRATIONS
Maintenance to be carried out at the intervals indicated in months or in operating hours which ever occurs first.
Frequency
Eachuse
Firstmonthor 5
hours
Every3
monthsor 25 hours
Every6
monthsor 50hours
Everyyear
or 100hoursItem Intervention
Engine oilCheck level
Change (1)
Air cleaner element
Check
Clean (1)
Change (1)
Grass bag Clean
Blade screw tightness and blade condition
Check
Spark plugCheck
Clean
Spark arrester(Optional part) Clean (6)
ROTOSTOP cable (3)
Check (2) (2)
Adjust if necessary (2) (2)
Blade brake cable (4)
Check
Adjust if necessary (2) (2)
ROTOSTOP (3) Check (2) (2)
Shift cable (5) Check
Throttle cableCheck (2) (2)
Adjust if necessary (2) (2)
Valve clearence
Adjust if necessary (2)
Fuel tank and filter Clean (2)
Fuel linesCheck(replace ifnecessary)
Every 2 years (2)
Flywheel brake shoe (4) Check (2)
Drive belt (5) Check (2)
Mower deck Clean
Possible cause Correction
Fuel valve OFF (closed). Turn the fuel valve ON (open) (page 7).
Throttle lever in the wrong position. Move the throttle lever to the "FAST" position (page 7).
Out of fuel. Refuel (page 4).
Bad fuel; mower stored without treating the petrol, or refueled with bad petrol. Refuel with fresh petrol (page 4).
Spark plug faulty, fouled, or improperly gapped. Gap or replace the spark plug (page 10).
Spark plug wet with fuel (flooded engine).Dry and reinstall the spark plug.Start the engine, with the throttle lever lever in "FAST" position.
Fuel tank vent blocked, carburettor clogged or ignition faulty.
Maintenance of these points must be carried out by a Honda dealer.
The blade brake lever is not firmly held against the handle (models fitted).
The blade brake lever must be held firmly against the handle for starting the engine (page 11).
Possible cause Correction
Throttle lever not set to "FAST". Move the throttle lever to "FAST" (page 7).
Grass is too tall to cut.Raise the cutting height (page 5), cut a narrower swath, use a slower ground speed (page 9), or cut more frequently.
Mower deck is clogged. Clean out the mower deck (page 11).
Air cleaner is clogged. Clean or replace the air cleaner (page 9).
Bad fuel; mower stored without treating the petrol, or refueled with bad petrol. Refuel with fresh petrol (page 4).
Fuel tank vent blocked, carburettor clogged or ignition faulty.
Maintenance of these points must be carried out by a Honda dealer.
Possible cause Correction
Engine speed is too slow to cut well. Move the throttle lever to the "FAST" position (page 7).
Mower is moving too "FAST" for lawn conditions.
Select a lower gear (equipped models) or push more slowly.
Grass bag overfilled or clogged.Empty the grass bag. Wash the grass bag if it is clogged with dirt (pages 9and 12).
Mower deck is clogged. Clean out the mower deck (page 11).
Blades dull, worn, or damaged. Sharpen or replace the blades if necessary (page 12).
Blades loose, bent, damaged, or unbalanced by improper sharpening.
Tighten loose blade bolts.If blades are found to be bent or damaged, take the lawn mower to an authorized Honda servicing dealer for inspection (page 12).
Mechanical damage, such as a bent crankshaft.
Maintenance of these points must be carried out by a Honda dealer.
14 EN
STORAGEPREPARATION FOR STORING THE MOWERCarry out the following operations to protect the mower each time it is to be stored for a period of more than 30 days.
Do not drain the fuel tank while the muffler is hot.
1. Drain the fuel tank and the carburettor into a suitable receptacle [1]:
a. Open the fuel cock [2].
b. Place the throttle lever lever [3] in "FAST" position [A] .
c. Unscrew the carburettor float bowl retaining bolt [4] (1/4 to 1/2 turn maximum).
d. Lift up the carburettor float bowl against the body of the carburettor [5] allowing the fuel to drain.
e. Refit the drain plug and close the fuel shut-off valve [2].
2. Change the engine oil (see page 10).3. Pull the starter slowly until a resistance is felt. This closes the
valves and protects them from dust and corrosion.4. Coat all surfaces liable to rust with a thin film of oil. Cover the
mower and store it on a flat surface in a dry, dust free place. Do not use a plastic cover since this retains dampness.
NOTE: If the mower is to be stored for a period of more than 3 months, remove the spark plug and pour 5 to 10 cc of clean engine oil into the cylinder; then pull the starter slowly two or three times to spread the oil. Do not leave the mower lying on its side over long periods. This may cause difficult starting and gear oil leaks.
FUEL STORAGENOTE:• Petrol will oxidize and deteriorate in storage.
Old petrol will cause hard starting, and it leaves gum deposits that clog the fuel system. If the petrol in your engine deteriorates during storage, you may need to have the carburetor and other fuel system components serviced or replaced.
• Ensure that you use containers or drums specifically designed for hydrocarbons [6]. This will prevent polluting the fuel through the dissolution of the container walls, which will lead to poor functioning of the engine.
• Store the fuel in a dark place, in a room at constant temperature (avoid garden sheds).
• The warranty does not cover a blocked carburetor or valves jammed by old or polluted fuel.
• The quality of unleaded petrol alters very quickly (2 to 3 weeks in some cases). Do not use fuel more than 1 month old. Store the absolute minimum required for your monthly consumption.
USING THE MOWER AFTER A STORAGE PERIOD
1. Remove the spark plug [7], check that it is clean and that the electrode gap is correct. Pull the starter several times.
2. We recommend that the spark plug be screwed down as far as possible by hand until finger tight; then use a plug spanner to tighten it by an extra 1/8 or 1/4 turn.
3. Check the level and condition of the engine oil [8].
4. Fill the fuel tank and start the engine.
NOTE: If the cylinder has been coated with oil, the engine will smoke on start-up. This is normal.
SAFETY D4D3
D2B3
[2]
STOP
SLOW
FAST
[A]
[3]
[A]
[3]
[1]
[4]
[4][5]
[2]
[6]
[7]
[8] Maxi
0.7 - 0.8 mm
15 EN
TRANSPORTTRANSPORTING THE MOWER
Do not tilt the mower since this may cause fuel or oil spillage; spilt fuel or even fuel vapours are a fire hazard.
To transport the mower:
1. Place the throttle lever in "STOP" position (except PKE, VKE types).
2. Pull off the spark plug cap.
3. Close the fuel shut-off valve [1].
To facilitate the operation:
1. Remove the grass bag (see page 12).
2. Turn the folding/handle adjustment knobs [2] a quarter turn to unlocked position [3].
3. Fold back the handle [4].
NOTE: After folding the handle, check that the cables are not kinked, twisted or stretched.
LOADING THE MOWER
CAUTION:• To prevent losing control of or damaging the mower, do not use
the drive system when going up or down a loading ramp.• To prevent damaging the drive system, do not engage the clutch
when the mower is rolling backwards.• Transport the mower in normal horizontal position with its four
wheels flat on the vehicle platform.• We recommend that you use a loading ramp or that you get
someone to help you load and unload the mower.• Adjust the loading ramp so that it is inclined at an angle of less
than 15°.• When transporting the mower, immobilise it using straps and
place chocks under the wheels.• The straps must not touch the following parts of the mower:
throttle lever, blade clutch lever, gas tank and all the control cables.
USEFUL INFORMATIONFIND AN APPROVED DEALERPlease refer to the European Internet site: http://www.honda-eu.com
CURRENT PARTS, OPTIONAL ACCESSORIES AND CONSUMABLESTo buy one of the original parts listed below, or any other part, please contact an approved Honda reseller.
For your safety, it is strictly prohibited to install any other attachment than the ones listed above and especially designed for your lawn mowers's model and type.
SAFETY C17C10
[1]
[4]
[2]
[2]
[3]
15° max.
HRX476C
Current parts
[5] Grass bag 81320-VK8-J50 Bag only (without frame)
72511-VK8-J50 Requires use of a dynamometric key[11] 72531-VK8-J50
[12] Recoil starter rope 28462-ZL8-631 Ask your Honda dealer
to replace these
Consumables
[13] Engine oil 08221-888-060HESAE 10W30, 0,6 l Oil for 4-stroke engines
[6]
[10][13][12]
[7] [8]
[9]
[11]
[5]
SAFETY D3C22
C4A2
16 EN
TECHNICAL SPECIFICATIONS
(*) The power rating of the engine indicated in this document is the net power output tested on a production engine for the engine modelGCV160E and measured in accordance with SAE J1349 at 3 600 rpm (Net Power). Mass production engines may vary from thisvalue. Actual power output for the engine installed in the final machine will vary depending on numerous factors, including theoperating speed of the engine in application, environmental conditions, maintenance, and other variables.
(**) Values for a machine equipped with a grass bag, in a grass collector position.
MODEL HRX476CTYPES PKE VKE VYE HYE
GENERAL CHARACTERISTICSDescription code MASFFunction Cutting of grass Dimensions L x W x h mm 1 600 x 530 x 1 010 1 545 x 530 x 960 1 610 x 530 x 1 035Dry weight kg 36 39 42 44Track FR/RR mm 430 / 453Cutting width mm 470Cutting heights settings mm 7 positions (25 to 79 mm)Rear/Front wheel diameter mm 212 / 212Grass bag capacity l 69Sound pressure level at operator’s ears (in accordance with directiveEN836: 1997 / AC: 2006) dB(A)
82 81
Measuring uncertainty dB(A) 1 2 1Measured sound power level (in accordance with directives 2000/14/EC, 2005/88/EC) dB(A) 93
Measuring uncertainty dB(A) 1Sound power level guaranteed (in accordance with directives 2000/14/EC, 2005/88/EC) dB(A) 94
Vibration test (in accordance with directivesEN836: 1997/AC: 2006, EN12096-D: 1997)(**)m/s2 3.5 5.6 4.2 2.7
Measuring uncertainty m/s2 1.8 2.2 2.1 1.4ENGINEModel GCV160EType Air-cooled overhead valve four-stroke engineDisplacement cc 160Bore x Stroke 64 x 50Cooling Forced airLubrication Spray lubricationCompression ratio 8.5 : 1Net power (*) kW/rpm 3.3 / 3 600Rated power kW/rpm 2.7 / 2 800
Operating speed rpm 2 800 Idle speed rpm 1 700 ± 150Ignition Transistorised magneto ignitionSpark plug NGK : BPR5ESElectrode gap mm 0.7 to 0.8Air cleaner Dry (paper) typeRecommended fuel Unleaded 95 or 98Fuel tank capacity l 0.93Fuel consumption l/h 0.58Running time on tank of fuel (*) h 1.6Recommended oil SAE 10W30Engine oil capacity l 0.55TRANSMISSIONType - Friction by cones HydrostaticEngine to drive - V-beltFinal transmission - GearNumber of speeds - Continuous variationForward speed m/s - 0 ~ 1.4Lubrication - Oil bath and projectionRecommended oil - SAE 10W30 API Grade SL / SJ Honda HSTOil capacity cc - 150 140
Company Ltd.New Street in San Gwakkin Road Mriehel Bypass, Mriehel QRM17
Tel. : +356 21 498 561Fax : +356 21 480 150
SLOVAK REPUBLICHonda Slovakia, spol. s r.o.Prievozská 6 - 821 09 Bratislava
Tel. : +421 2 32131112Fax : +421 2 32131111
http://www.honda.sk
FINLANDOY Brandt AB.Tuupakantie 7B01740 Vantaa
Tel. : +358 20 775 7200Fax : +358 9 878 5276
http://www.brandt.fi
NETHERLANDSHonda Nederland B.V.
Afd. Power Equipment-Capronilaan 11119 NN Schiphol-RijkTel. : +31 20 7070000Fax : +31 20 7070001http://www.honda.nl
SLOVENIAAS Domzale Moto Center D.O.O.
Blatnica 3A1236 Trzin
Tel. : +386 1 562 22 42Fax : +386 1 562 37 05
http://www.as-domzale-motoc.si
Major Honda distributor addressesAdresses des principaux concessionnaires HondaAdressen derwichtigsten Honda-HaupthändlerElenco dei maggiori distributori Honda in EuropaAdressen van Honda-importeursDirecciones de los principales concesionarios Honda
EC - Prohlášení o shodĕ1) Zástupce výrobce, Takayoshi Fukai svým podpisem potvrzuje, že daný výrobek splňuje
požadavky Smĕrnice pro strojní zařízení Daný výrobek rovnĕž splňuje požadavky následujících Smĕrnic:
- Hluková smĕrnice: - Smĕrnice pro elektromagnetickou kompatibilitu: 2) Popis zařízení: a) Všeobecné označení: Sekačky na trávu b) Funkce: Sekání trávy
c) Typ: d) Výrobní císlo:3) Hluková smĕrnice: a) Namĕřený akustický výkon - b) Garantovaný akustický výkon c) Parametry: Nominální výkon - d) Způsob stanovení shody - e) Notifikovaná osoba:4) Výrobce:5) Autorizovaná osoba povĕřená schvalováním technické dokumentace:6) Odkazy na harmonizované normy:7) Ostatní použité národní normy a specifikace: Podepsáno v: Datum: Prezident: Podpis:
EU Overenstemmelseerklæring1) Undertegnede,Takayoshi Fukai, som repræsenterer producenten erklærer herved, at produktet
beskrevet nedenfor opfylder alle retningslinier i maskindirektivet. Produktet opfylder også bestemmelserne i:
- Direktiv om støjemission fra maskiner til udedørs brug: - EMC direktiv: 2) Beskrivelse af produktet: a) Fællesbetegnelse: Plæneklipper b) Anvendelse: Græsklipning
c) Type: d) Stelnummer:3) Direktiv om støjemission fra maskiner til udedørs brug: a) Målt støjniveau - b) Garanteret støjniveau - c) Støjparameter: Installeret motoreffekt
d) Overenstemmelsens vurderingsprocedure - e) Bemyndiget organ 4) Producent:5) Autoriseret repræsentant for udfærdigelsen af den tekniske dokumentation:6) Reference til harminiserede standarder:7) Andre nationale standarder eller specifikationer: Sted: Dato: Formand: Underskrift:
EG-Konformitätserklärung1) Der Unterzeichner,Takayoshi Fukai der den Hersteller vertritt, erklärt hiermit dass die unten
genannte Maschine den Bestimmungen aller relevanten Maschinenrichtlinien entspricht. Die Maschine entspricht ebenfalls den Vorschriften der:
- Outdoor Richtlinie: - EMV Richtlinie:2) Beschreibung der Maschine: a) Allgemeine Bezeichnung: Rasenmäher b) Funktion: Gras schneiden
c) Typ: d) Seriennummer:3) Richtlinie zu Geräuschemissionen im Freien: a) Gemessener Schallleistungspegel - b) Garantierter Schallleistungspegel - c) Geräusch
Vorgabe: Tatsächliche Leistung - d) Angewandtes Konformitätsbewertungsverfahren e) Benannte Stelle 4) Hersteller:5) Bevollmächtigter zur Erstellung der technischen Unterlagen:6) Verweis auf harmonisierte Normen:7) Andere herangezogene nationale Normen, Bestimmungen oder Vorschriften: Ort: Datum: Präsident: Unterschrift:
Declaracion de conformidad CE. 1) El firmante, Takayoshi Fukai, en representación del fabricante, adjunto declara que la máquina
descrita más abajo cumple con todas los requisitos relevantes de la Directiva de Maquinaria. La máquina también cumple con los requisitos de la:
- Directiva sobre Ruido exterior: - Directiva EMC:2) Descripción de la máquina: a) Denominación genérica: Cortacésped b) Función: Cortar el césped
c) Tipo: d) Número serie:3) Directiva Ruido Exterior: a) Potencia medida sonido - b) Potencia sonido garantizada - c) Parámetros ruido:
4) Fabricante:5) Representante autorizado para recopilar la Documentación Técnica:6) Referencia de los estándar harmonizados:7) Otros estándar nacionales o especificaciones: Realizado en: Fecha: Presidente: Firma:
vastavad kõikidele Tehniliste seadmete direktiivinõuetele. Lisaks selle vastavad seadmed järgmiste direktiivide nõuetele:
- Müratase välitingimustes: - EMC direktiiv: 2) Seadmete kirjeldus: a) Üldnimetus: Muruniiduk b) Funktsiooon: Muru niitmine c) Tüüp: d) Seerianumber:3) Müratase välitingimustes: a) Mõõdetav helivõimsuse tase - b) Tegelik helivõimsuse tase - c) Müra mõjutavad tegurid: Toite
võimsus - d) Vastavushindamise menetlus - e) Teavitatud asutus 4) Tootja:5) Volitatud esindaja, kes on kvalifitseeritud koostama tehnilist dokumentatsiooni:6) Viide ühtlustatud standarditele:7) Siseriiklikud seadusaktid: Koht: Kuupäev: President: Allkiri:
Déclaration CE de conformité1) Le soussigné, Mr Takayoshi Fukai, représentant du constructeur, déclare par la présente que
la machine décrite ci-dessous est conforme aux dispositions de la Directive Machine. Cette machine répond également aux dispositions de :
- Directive relative aux émissions sonores dans l'environnement des matériels destinés à être utilisés à l'extérieur des bâtiments : - Directive relative à la compatibilité électromagnétique des équipements électriques
et électroniques :2) Description de la machine : a) Denomination générique : Tondeuse à gazon b) Fonction : Couper de l'herbe (tondre)
c) Type : d) Numéro de série :3) Directive relative aux émissions sonores dans l'environnement des matériels destinés à être
utilisés à l'extérieur des bâtiments : a) Puissance acoustique mesurée b) Puissance acoustique garantie c) Paramètres de bruit: Puissance nette installée d) Procédure d'évaluation de la conformité e) Organisme notifié.4) Constructeur :5) Représentant autorisé à valider la documentation technique :6) Référence aux normes harmonisées :7) Autres normes et spécifications techniques nationales : Fait à : Date : Président : Signature :
EU-vaatimustenmukaisuusvakuutus1) Allekirjoittanut valmistajan edustaja Takayoshi Fukai vakuuttaa täten, että tuote on kaikkien EU: n konedirektiivin vaatimusten mukainen. Tuote on lisäksi seuraavien EU: n direktiivien vaatimusten mukainen: - Meludirektiivi: - sähkömagneettista yhteensopivuutta koskeva direktiivi: 2) Tuotteen kuvaus: a) Yleisarvomäärä: Ruohonleikkuri b) Toiminto: Ruohon leikkaus
c) Tyyppi: d) Sarjanumero:3) Meludirektiivi: a) Mitattu äänitehotaso - b) Taattu äänitehotaso - c) Meluparametrit: asennettu nettoteho
Πιστοποιητικό συμμόρφωσης Ε.Ε.1) Ο υπογράφων,Takayoshi Fukai εκπροσωπόντας τον κατασκευαστή, δια του παρόντος
δηλώνει ότι το μηχάνημα που αναφέρεται πιό κάτω βρίσκεται σε εναρμόνιση με τις προβλέψεις των οδηγιών της ΕΕ. Τα μηχανήματα βρίσκονται σε εναρμόνιση με τις προβλέψεις των:
γ) Τύπος: δ) Αριθμός παραγωγής:3) Οδηγία θορύβου εξωτερικού χώρου: α) Ισχύς μετρηθέντος θορύβου - β) Εγγυημένο επίπεδο θορύβου - γ) Παραμέτροι θορύβου: ισχύς κινητήρα - δ) Διαδικασία αξιολόγησης συμμόρφωσης - ε) Όνομα κοινοποιημένου
οργανισμού 4) Κατασκευαστής:5) Εγγεκριμένος αντιπρόσωπος ικανός γιά σύσταση τεχνικού συγγράμματος:6) Αναφορά σε εναρμονισμένα πρότυπα:7) Αναφορά σε άλλα εθνικά πρότυπα ή προδιαγραφές: Η δοκιμή έγινε: Ημερομηνία: Πρόεδρος: Υπογραφή:
EK-Megfelelőségi nyilatkozat1) Alulírott Takayoshi Fukai, mint a gyártó képviselője nyilatkozom, hogy az alábbi berendezés
mindenben megfelel a Gépekre irányuló rendelkezéseknek: A berendezés megfelel a Külső Hangkbocsátási és a EMC Direktíváknak2) A gép leírása: a) Általános megnevezés: Fűnyíró b) Funkció: Fű levágása
c) Típus: d) Sorozatszám: 3) Külső hangkibocsátási előírások: a) Mért hangerő b) Garantált hangerő c) Zaj paraméter: Üzembehelyezett zajszint
d) Becslési eljárás megfelelősséghez e) Bejegyzett teszt4) Gyártó:5) Műszaki dokumentáció összeállítására jogosult képviselő:6) Hivatkozással a szabványokra:7) Más belföldi előírások, megjegyzések: Keltezés helye: Keltezés ideje: Elnök: Aláírás:
EC - Декларация за съответствие1) Долуподписалият се Г-н Канемура, представляващ производителя, с настоящия
документ декларира че машина описана по-долу е в съответствие с всички изисквания на директивите за машини и съоръжения - Съоръжението също съответства с изискванията на:
- Директива за нивото на шума: - EMC директива: 2) Описание на оборудването: а) Общо наименование: косачка б) Функция: косене на трева
в) Тип: д) Сериен номер: 3) Външен шум: а) измерена сила на звука - b) максимална сила на звука - c) параметри на шума; нетна инсталирана мощност - d) процедура на измерването - e) измерено на купе 4) Производител:5) Оторизиран представител, който може да съставя техническата документация:6) Съответствие с хармонизирани етандарти:7) Други национални стандарти и спецификации: Място на изготвяне: Дата на изготвяне: Мениджър по качество: Подпис:
4) Manufacturer: Honda France Manufacturing S.A.S. Pôle 45 - Rue des Châtaigniers 45140 ORMES - FRANCE5) Authorized Representative able to compile the technical documentation: Honda France Manufacturing S.A.S. Pôle 45 - Rue des Châtaigniers 45140 ORMES - FRANCE6) Reference to harmonized standards EN ISO 14982 : 19987) Other national standards or specifications EN 836 : 1997 / AC : 2006
1) The undersigned, Mr Takayoshi Fukai, representing the manufacturer, herewith declares that the machinery described below complies with all the relevant provisions of the Machinery Directive 2006/42/EC.
The machinery also complies with the provisions of the: - Outdoor noise Directive: 2000/14/EC, 2005/88/EC - EMC Directive: 2004/108/EC2) Description of the machinery: a) Generic denomination: Lawn mower b) Function: Cutting of grass c) Type: HRX476C1 (PKE, VKE, VYE, HYE) d) Serial number:
3) Outdoor noise Directive: a) Measured sound power: 93 dB(A)
b) Guaranteed sound power: 94 dB(A) c) Noise parameter: L = 47 cm d) Conformity assessment procedure: Annex VI e) Notified body: CEMAGREF Groupement d'Antony - Parc de Tourvoie - BP 44 92163 ANTONY Cedex - France
MASF 1130000 ~ 1175648
18
EB-Samræmisyfirlýsing1) Undirritaður, Mr Takayoshi Fukai, fyrir hönd framleiðandans, lýsir hér með yfir því að vélin sem
lýst er hér að neðan samræmist öllum gildandi ákvæðum tilskipunar: Vélbúnaðurinn samræmist einnig ákvæðum tilskipunar um hávaðamengun utanhúss: - EMC tilskipunin2) Lýsing á vélbúnaði: a) Almennt heiti: Garðsláttuvél b) Verkunarmáti: Grassláttur c) Tegund: d) Raðnúmer:3) Tilskipun varðandi hávaðamengun utanhúss a) Mælt hljóðafl: b) Hljóðafl sem ábyrgst er: c) Hávaðaviðmun: d) Aðferð við samræmingarmat: Viðauki VI e) Tilkynntum aðila:4) Framleiðandi5) Viðurkenndur fulltrúi sem hefur heimild til að taka saman viðkomandi tækniskjal6) Tilvísun í samræmda staðla7) Aðrir innlendir staðlar eða tækniforskriftir Gjört í: Dags.: Formaður stjórnar: Undirritun:
Dichiarazione di conformità1) Il sottoscritto,Takayoshi Fukai in rappresentanza del costruttore, dichiara qui di seguito che la
macchina sotto descritta è conforme con tutte le condizioni pertinenti della Direttiva Macchine. La macchina è anche conforme alle condizioni della:
- Direttiva sulle emissioni acustiche delle macchine destinate a funzionare all'aria aperta: - Direttiva sulla compatibilità elettromagnetica:
2) Descrizione della macchina: a) Denominazione generica: Rasaerba b) Funzione: Taglio di erba c) Tipo: d) Numero di serie:3) Direttiva emissioni acustiche: a) Livello di potenza sonora misurata - b) Livello di potenza sonora garantita c) Parametri rumorosità: Potenza netta installata - d) Procedura di valutazione conformità e) Organismo notificato 4) Costruttore:5) Rappresentante Autorizzato idoneo a compilare la documentazione tecnica:6) Riferimento agli standard armonizzati:7) Altri standard o specifiche nazionali Fatto a: Data: Presidente: Firma:
EB Atitikties Deklaracija.1) Žemiau pasirašes, p. Takayoshi Fukai atstovaujantis gamintoją, deklaruoja, kad įranga
atitinka reikalavimus pagal direktyvą:2) Mašinos aprašymas: a) Bendras pavadinimas: Vejapjovė b) Funkcija: Žolės pjovimas c) Tipas: d) Serijinis numeris:3) Triukšmo direktyva: a) Išmatuotas riukšmo lygis - b) Garantuotas triukšmo lygis - c) Triukšmo parametrai: Nominali instaliuota galia - d) Atitikties įvertinimo procedūra - e) Atstovas.4) Gamintojas:5) Įgaliotas atstovas turintis techninę dokumentaciją:6) Nuoroda į harmonizuotus standartus:7) Kiti nacionaliniai standartai ir specifikacijos: Atlikta: Data: Prezidentas: Parašas:
EK Atbilstības deklarācija1) Zemāk minētais Takayoshi Fukai, kā ražotāja pārstāvis ar šo apstiprina, ka atrunātā iekārta
pilnībā atbilst visiem standartiem, kas atrunāti EC-Direktīvā Kā arī šī iekārta atbilst: - trokšņa līmeņa direktīvai:
- EMC direktīvai:2) Lekārtas apraksts: a) Vispārējais nosukums: Zāles pļāvējs b) Funkcija: Zāles pļaušana c) Tips: d) Sērijas numurs:3) Trokšņa līmeņa direktīva: a) Nomērītā trokšņa jauda - b) Garantētā trokšņa jauda - c) Trokšņa parametri: Kopējā uzstādītā jauda - d) Atbilstības noteikšanas procedūra - e) Atbildīgā iestāde4) Ražotājs:5) Autorizētais pārstāvis, kas ir kompetents apkopot tehnisko dokumentāciju:6) Atsaucoties uz saskaņotajiem standartiem:7) Citi valsts noteiktie standarti vai specifikācijas: Vieta: Datums: Prezidents: Paraksts:
EU-Conformiteitsverklaring1) Ondergetekende, Takayoshi Fukai, vertegenwoordiger van de constructeur, verklaart
hierbij dat de hieronder beschreven machine in overeenstemming is met de bepalingen van de Veiligheidsrichtlijn voor machines. De machine voldoet eveneens aan de bepalingen van de richtlijnen voor geluidsemissie van materieel voor gebruik buitenshuis en elektromagnetisme.
2) Beschrijving van de machine: a) Algemene benaming: Gazonmaaier b) Functie: Gras maaien c) Type: d) Serienummer:3) Geluidsemissie materieel voor gebruik buitenhuis: a) Gemeten geluidsvermogen - b) Gegarandeerd geluidsvermogen - c) Geluidsparameter: Gëinstalleerd vermogen - d) Conformiteitsbeoordelingprocedure - e) In kennis gestelde instantie4) Konstrukteur :5) Vertegenwoordiger die gemachtigd is om de technische documentatie samen te
stellen:6) Verwijzing naar geharmoniseerde normen:7) Andere nationale normen of technische specificaties: Opgemaakt te: Datum: President: Handtening:
EU samsvarserklæring1) Undertegnede, Takayoshi Fukai representerer produsenten og erklærer herved at produktet
beskrevet nedenfor er i samsvar med relevante forskrifter i Maskindirektivet. Produktet samsvarer også med forskrifter vedr:
- Rammedirektiv for utendørs støy: - EMC direktiv2) Produktbeskrivelse: a) Felles benevnelse: Gressklipper b) Funksjon: Klippe gress c) Type: d) Serienummer:3) Rammedirektiv om utendørs støy: a) Målt lydeffekt - b) Garantert lydeffekt - c) Støyparameter: Netto installert effekt d) Valgt samsvarsprosedyre - e) Teknisk kontrollorgan4) Produsent:5) Autorisert representant/innehaver av teknisk dokumentasjon:6) Referanse til harmoniserte standarder:7) Øvrige nasjonale standarder eller spesifikasjoner: Sted: Dato: Formann: Underskrift:
opisane poniżej jest zgodne z wszystkimi zasadniczymi wymaganiami Dyrektywy Maszynowej. Urządzenie spelnia dodatkowo wymagania:
- Dyrektywy Halasowej: - Dyrektywy EMC:2) Opis urządzenia: a) Ogólne określenie: Kosiarka b) Funkcja: Ścinanie trawy c) Typ: d) Numery seryjne:3) Dyrektywa Halasowa: a) Zmierzony poziom mocy akustycznej - b) Gwarantowany poziom mocy akustycznej c) Parametrycharakterystyczne: Zainstalowana moc netto d) Zastosowana procedura oceny zgodnosci - e) Jednostka Notyfikowana4) Producent:5) Upoważniony Przedstawiciel posiadający dostęp do dokumentacji technicznej:6) Zastosowane normy zharmonizowane:7) Pozostale normy i przepisy krajowe: Miejsce: Data: Prezes: Podpis:
Declaração CE de conformidade1) O abaixo assinado, Takayoshi Fukai, representante do fabricante, declara que a maquinaria
abaixo descrita cumpre com todas as normas referentes á Directiva de Maquinaria. A maquinaria também cumpre as directivas de:
- Directiva de ruído no exterior: - Directiva EMC: 2) Descrição da maquinaria: a) Denominação genérica: Corta-relvas b) Função: Corte de relva c) Tipo: d) Número série:3) Directiva de ruido no exterior: a) Potência de som medida - b) Potência de som garantida - c) Parâmetros de ruido: d) Procedimento da avaliação da conformidade - e) Organismo notificado 4) Fabricante:5) Representante autorizado e apto para confirmar a documentação técnica:6) Referência aos padrões harmonizados:7) Outras normas nacionais ou especificações: Feito em: Data: Presidente: Assinatura:
UE -Declaratie de Conformitate1) Subsemnatul Takayoshi Fukai, reprezentand producatorul, declara prin prezenta ca
chipamentele mai descrise mai jos respecta toate prevederile relevante din Directiva privind echipamentele Echipamentele respecta de-asemenea prevederile Directivei privind nivelul
de zgomot exterior si Directiva EMC:2) Descrierea echipamentului: a) Denumire generica: Cositoare gazon b) Domeniu de utilizare: Tunderea ierbii
c) Tip: d) Numar de serie: 3) Directiva privind zgomotul exterior: a) Puterea sonora masurata: - b) Puterea sonora garantata: - c) Parametrii de zgomot putere instalata neta - d) Procedura de evaluare a conformitatii: - e) Organismul notificat4) Producator:5) Reprezentantul Autorizat in masura sa intocmeasca documentatia tehnica:6) Referinta la standardele armonizate:7) Alte standarde nationale sau specificatii: Emisa la: Data: Prezident: Semnatura:
EG-deklaration för överensstämmande1) Undertecknad, Takayoshi Fukai, representant för tillverkaren, försäkrar härmed att maskinerna
beskrivna nedan uppfyller alla relevanta stadgar i Maskin Direktivet eller Maskinerna uppfyller också stadgarna för:
- Utomhus bullerdirektiv: - EMC direktiv:2) Maskinbeskrivning: a) Allmän benämning: Gräsklippare b) Funktion: Gräsklippning c) Typ: d) Serie nummer:3) Utomhus bullerdirektiv: a) Uppmätt ljudeffekt - b) Garanterad ljudeffekt - c) Bullerparameter: Installerad nettoeffekt d) Utvärderingsprocedur för överensstämmande - e) Anmälda organ 4) Tillverkare:5) Auktoriserad representant som kan sammanställa den tekniska dokumentationen:6) Referens till överensstämmande standarder:7) Andra nationella standarder eller specifikationer: Utfärdat vid: Datum: Ordförande: Underskrift:
Vyhlásenie o súlade s predpismi ES1) Dolupodpísaný pán Takayoshi Fukai zastupujúci výrobcu týmto vyhlasuje, že stroje
popísané nižšie vyhovujú všetkým relevantným predpisom smernice Stroje vyhovujú predpisom: - EMC direktiva:
2) Popis strojov: a) Druhové označenie: Kosačky na trávu b) Funkcia: Kosenie trávy c) Typ: d) Sériové číslo:3) Smernica emisií hluku vo voľnom priestranstve: a) Nameraný akustický tlak - b) Garantovaný akustický tlak - c) Parameter hluku: Nominálny čistý výkon - d) Proces posudzovania zhody - e) Notifikovaný orgán 4) Výrobca:5) Autorizovaný zástupca schopný predložiť technickú dokumentáciu:6) Referencia k harmonizovaným štandardom:7) Ďaľšie národné štandardy alebo špecifikácie: Miesto: Dátum: Predseda: Podpis:
ES-Izjava o skladnosti1) Spodaj podpisani, Takayoshi Fukai, ki predstavljam proizvajalca, izjavljam da so spodaj
navedene naprave v skladu z direktivo Naprave prav tako ustrezajo naslednjim direktivam: - Direktiva o hrupnosti: - EMC direktiva: 2) Opis naprav: a) Vrsta stroja: Vrtne kosilnica b) Funkcija: Košenje trave c) Tip: d) Serijska številka:3) Direktiva o hrupnosti: a) Izmerjena zvocna moč - b) Garantirana zvočna moč - c) Parametri: Neto moč d) Postopek meritve - e) Testiranja opravil 4) Proizvajalec:5) Pooblaščeni predstavnik, ki hrani tehnično dokumentacijo:6) Upoštevani harmonizirani standardi:7) Ostali standardi: Kraj: Dátum: Predsednik: Podpis:
AB Uygunluk Beyanı1) Ben aşağıda imzası bulunan, Takayoshi Fukai, işburada imalatçı firmayı temsilen
aşağıda belirtilen makinelerin 2006/42/EEC sayılı Makine Direktifinin ilgili tüm hükümlerine uygun olduğunu beyan ediyorum. Bu makineler aşağıda belirtilen direktiflerin hükümlerine de uygundur:
- Dış mekan gürültü Direktifi: - EMC Direktifi:2) Makinelerin açıklaması: a) Genel adı: Çim biçme makinesi b) İşlevi: Çim kesme c) Tipi: d) Seri numarası:3) Dış mekan gürültü Direktifi: a) Ölçülen ses gücü: b) Garantili ses gücü: c) Ses parametresi:
d) Uygunluk değerlendirme prosedürü: Ek VI e) Onaylanmış kuruluş:4) İmalatçı:5) Teknik belgeleri düzenleyebilecek Yetkili Temsilci:6) Uyumlulaştırılmış standartlara atıf:7) Diğer ulusal standartlar veya spesifikasyonlar: Düzenlendiği yer: Tarih: Başkan: İmza: 19
