1ADVANTAGE-SCIENTIFIC.COM12/20
FUME HOODS
HIGH SIGHT LINE GEN IIVERTICAL SASH
2
HIGH SIGHT LINE GEN IICOMBINATION SASH
4
MULTI-UNIT GEN IIVAV - VARIABLE AIR VOLUME
6
DEMONSTRATION GEN IIFRONT/REAR SASH
8
ADA GEN IIVERTICAL SASH
12
STAND-ALONE OR MULTI-UNIT GEN II3-SIDE VIEW WORKSTATION
10
ADA GEN IICOMBINATION SASH
14
BASIC GEN IIBY-PASS
16
PORTABLE GEN II 18
ACCESSORIES 21
FACTORY-INSTALLED ACCESSORIES 22
BASE CABINETS 19
MOBILE CABINETS 20
©2020 STEVENS INDUSTRIES, INC.ALL RIGHTS RESERVED. Due to continuing product development, Stevens reserves the right to change specifications without notice.
2 1 .217.857.710012/20
High Sight Line GEN IIVertical Sash
FUME HOODS
GEN Design is high performance hood as an individual hood for constant volume extraction blower (not included). Hood incorporates both by-pass and airfoil features.
The GEN II design has contour form vertical side posts and slope back header with radius lower horizontal edge. Design promotes smooth airflow into hood opening. Hood fascia has 36" high clear sight view. Full opening 29" sash ideal for unrestricted equipment setup access. Advantage Scientific hood includes standard 18" vertical sash stops to promote efficient working extraction and face velocity.
3 models available: 51805485632: 48"W x 56"H x 32 1/4"D 51805605632: 60"W x 56"H x 32 1/4"D 51805725632: 72"W x 56"H x 32 1/4"D
CONSTRUCTION FEATURES• Solid galvanized frame construction allows
disassembly for constricted installation access areas• Powder coat exterior finishes• Shaft drive sash• Polyresin liner• LED light fixture• Stainless steel full width finger lift sash• 18" open sash stop• 10" exhaust duct collar
STANDARD EQUIPMENT (factory installed)• 2 GFI duplex• Blower switch• Light switch• Cup sink• Remote cold water faucet• Remote gas fixture• Black epoxy 1/4" dish top
FACTORY-INSTALLED ADDS• 52005 Airflow monitor• 52006 Digital airflow monitor• 52007 External vacuum breaker
OPTION ACCESSORIES• 52001 Ceiling enclosure• 52004 Lattice assembly
51805 STYLE
Same as 51805, with additional remote air fixture and remote vacuum fixture.
3 models available: 51806485632: 48"W x 56"H x 32 1/4"D 51806605632: 60"W x 56"H x 32 1/4"D 51806725632: 72"W x 56"H x 32 1/4"D
51806 STYLE
MUST BE ORDERED WITH FUME HOOD. NOT SOLD SEPARATELY.52005 Factory-Installed Airflow Monitor (details on page 22)52006 Factory-Installed Digital Airflow Monitor (details on page 22)52007 Factory-Installed External Vacuum Breaker (as required by specific local, city or state codes)
FACTORY-INSTALLED ADDS
OF EXHAUST DUCT
CL
33.75"
10"
20"
36"29"MaxSash
Height
57.25"
24.50"
1.25"30"
48"
10" Dia.SS Duct Collar
3ADVANTAGE-SCIENTIFIC.COM12/20
High Sight Line GEN IIVertical Sash
FUME HOODS
51805605632 / 51806605632
51805485632 / 51806485632
51805725632 / 51806725632
W H DSuperstructure: 48 56 321⁄4Worktop: 48 11⁄4 30Hood Opening: 38 29Hood View: 38 36
Exhaust Parameters: 739 CFM .26 SPHood Weight: 200 pounds (approx.)
W H DSuperstructure: 60 56 321⁄4Worktop: 60 11⁄4 30Hood Opening: 50 29Hood View: 50 36
Exhaust Parameters: 972 CFM .32 SPHood Weight: 225 pounds (approx.)
W H DSuperstructure: 72 56 321⁄4Worktop: 72 11⁄4 30Hood Opening: 62 29Hood View: 62 36
Exhaust Parameters: 1206 CFM .41 SPHood Weight: 270 pounds (approx.)
BASE CABINETS(SEE OFFERING BELOW)
48" BASE CABINET ORTWO 24" BASE CABINETS
(ANY COMBINATION)
519005191051920
519005191051920
24W 24W
5190341489
48W
60" BASE CABINET ORTWO 30" BASE CABINETS
(ANY COMBINATION)
519015191151921
519015191151921
30W 30W
41489
60W
TWO 36" BASE CABINETS 0RTHREE 24" BASE CABINETS
(ANY COMBINATION)
519005191051920
24W
519005191051920
24W
519005191051920
24W36W
519025191251922
36W
519025191251922
BASE CABINET OFFERING (DETAILS ON PAGES 19-20)
36W
51902 51912 51922
30W
51901 51911 5192151900 51910
24W
51920
48W
51903 41489 41489
60W
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
4 1 .217.857.710012/20
High Sight Line GEN IICombination SashFUME HOODS
GEN Combination sash with sliding door panels in vertical sash frame. Combination sash allows vertical sash to be down while sliding door panel may be opened for access, reducing open exposure to hood interior as added safety feature. Design is high performance hood as an individual hood for constant volume extraction blower (not included). Hood incorporates both by-pass and airfoil features.
The GEN II design has contour form vertical side posts and slope back header with radius lower horizontal edge. Design promotes smooth airflow into hood opening. Hood fascia has 36" high clear sight view. Full opening 29" sash ideal for unrestricted equipment setup access. Advantage Scientific hood includes standard 18" vertical sash stops to promote efficient working extraction and face velocity.
3 models available: 51810485632: 48"W x 56"H x 32 1/4"D 51810605632: 60"W x 56"H x 32 1/4"D 51810725632: 72"W x 56"H x 32 1/4"D
CONSTRUCTION FEATURES• Solid galvanized frame construction allows
disassembly for constricted installation access areas• Powder coat exterior finishes• Shaft drive sash• Polyresin liner• LED light fixture• Stainless steel full width finger lift sash• Vertical sash with horizontal sliding panes• 18" open sash stop• 10" exhaust duct collar
STANDARD EQUIPMENT (factory installed)• 2 GFI duplex• Blower switch• Light switch• Cup sink• Remote cold water faucet• Remote gas fixture• Black epoxy 1/4" dish top
FACTORY-INSTALLED ADDS• 52005 Airflow monitor• 52006 Digital airflow monitor• 52007 External vacuum breaker
OPTION ACCESSORIES• 52001 Ceiling enclosure• 52004 Lattice assembly
51810 STYLE
Same as 51810, with additional remote air fixture and remote vacuum fixture.3 models available: 51811485632: 48"W x 56"H x 32 1/4"D 51811605632: 60"W x 56"H x 32 1/4"D 51811725632: 72"W x 56"H x 32 1/4"D
51811 STYLE
MUST BE ORDERED WITH FUME HOOD. NOT SOLD SEPARATELY.52005 Factory-Installed Airflow Monitor (details on page 22)52006 Factory-Installed Digital Airflow Monitor (details on page 22)52007 Factory-Installed External Vacuum Breaker (as required by specific local, city or state codes)
FACTORY-INSTALLED ADDS
OF EXHAUST DUCT
CL
33.75"
10"
20"
36"29"MaxSash
Height
57.25"
24.50"
1.25"30"
48"
10" Dia.SS Duct Collar
5ADVANTAGE-SCIENTIFIC.COM12/20
High Sight Line GEN IICombination SashFUME HOODS
51810485632 / 51811485632
51810605632 / 51811605632
51810725632 / 51811725632
W H DSuperstructure: 48 56 321⁄4Worktop: 48 11⁄4 30Hood Opening: 38 29Hood View: 38 36
Exhaust Parameters: 739 CFM .26 SPHood Weight: 200 pounds (approx.)
W H DSuperstructure: 60 56 321⁄4Worktop: 60 11⁄4 30Hood Opening: 50 29Hood View: 50 36
Exhaust Parameters: 972 CFM .32 SPHood Weight: 225 pounds (approx.)
W H DSuperstructure: 72 56 321⁄4Worktop: 72 11⁄4 30Hood Opening: 62 29Hood View: 62 36
Exhaust Parameters: 1206 CFM .41 SPHood Weight: 270 pounds (approx.)
BASE CABINETS(SEE OFFERING BELOW)
48" BASE CABINET ORTWO 24" BASE CABINETS
(ANY COMBINATION)
519005191051920
519005191051920
24W 24W
5190341489
48W
60" BASE CABINET ORTWO 30" BASE CABINETS
(ANY COMBINATION)
519015191151921
519015191151921
30W 30W
41489
60W
TWO 36" BASE CABINETS 0RTHREE 24" BASE CABINETS
(ANY COMBINATION)
519005191051920
24W
519005191051920
24W
519005191051920
24W36W
519025191251922
36W
519025191251922
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
BASE CABINET OFFERING (DETAILS ON PAGES 19-20)
36W
51902 51912 51922
30W
51901 51911 5192151900 51910
24W
51920
48W
51903 41489 41489
60W
6 1 .217.857.710012/20
Multi-Unit GEN IIVAV - Variable Air Volume
FUME HOODS
GEN Variable air volume (VAV) restrictive by-pass hood. High performance hood designed for lab with multiple installed hoods and central extraction blower. Airflow balancing and blower by HVAC mechanical contractor. Hood incorporates flush mount airfoil.
The GEN II design has contour form vertical side posts and slope back header with radius lower horizontal edge. Design promotes smooth airflow into hood opening. Hood fascia has 36" high clear sight view. Full opening 29" sash ideal for unrestricted equipment setup access. Advantage Scientific hood includes standard 18" vertical sash stops to promote efficient working extraction and face velocity.
3 models available: 51815485632: 48"W x 56"H x 32 1/4"D 51815605632: 60"W x 56"H x 32 1/4"D 51815725632: 72"W x 56"H x 32 1/4"D
CONSTRUCTION FEATURES• Solid galvanized frame construction allows
disassembly for constricted installation access areas• Powder coat exterior finishes• Shaft drive sash• Polyresin liner• LED light fixture• Stainless steel full width finger lift sash• 18" open sash stop• 10" exhaust duct collar
STANDARD EQUIPMENT (factory installed)• 2 GFI duplex• Blower switch• Light switch• Cup sink• Remote cold water faucet• Remote gas fixture• Black epoxy 1/4" dish top
FACTORY-INSTALLED ADDS• 52005 Airflow monitor• 52006 Digital airflow monitor• 52007 External vacuum breaker
OPTION ACCESSORIES• 52001 Ceiling enclosure• 52004 Lattice assembly
51815 STYLE
Same as 51815, with additional remote air fixture and remote vacuum fixture.3 models available: 51816485632: 48"W x 56"H x 32 1/4"D 51816605632: 60"W x 56"H x 32 1/4"D 51816725632: 72"W x 56"H x 32 1/4"D
51816 STYLE
MUST BE ORDERED WITH FUME HOOD. NOT SOLD SEPARATELY.52005 Factory-Installed Airflow Monitor (details on page 22)52006 Factory-Installed Digital Airflow Monitor (details on page 22)52007 Factory-Installed External Vacuum Breaker (as required by specific local, city or state codes)
FACTORY-INSTALLED ADDS
OF EXHAUST DUCT
CL
33.75"
10"
20"
36"29"MaxSash
Height
57.25"
24.50"
1.25"30"
48"
10" Dia.SS Duct Collar
7ADVANTAGE-SCIENTIFIC.COM12/20
Multi-Unit GEN IIVAV - Variable Air Volume
FUME HOODS
51815485632 / 51816485632
51815605632 / 51816605632
51815725632 / 51816725632
Designed for multiple unit installations with common blower extraction system.
Designed for multiple unit installations with common blower extraction system.
Designed for multiple unit installations with common blower extraction system.
W H DSuperstructure: 48 56 321⁄4Worktop: 48 11⁄4 30Hood Opening: 38 29Hood View: 38 36
Exhaust Parameters: 739 CFM .26 SPHood Weight: 200 pounds (approx.)
W H DSuperstructure: 60 56 321⁄4Worktop: 60 11⁄4 30Hood Opening: 50 29Hood View: 50 36
Exhaust Parameters: 972 CFM .32 SPHood Weight: 225 pounds (approx.)
W H DSuperstructure: 72 56 321⁄4Worktop: 72 11⁄4 30Hood Opening: 62 29Hood View: 62 36
Exhaust Parameters: 1206 CFM .41 SPHood Weight: 270 pounds (approx.)
BASE CABINETS(SEE OFFERING BELOW)
48" BASE CABINET ORTWO 24" BASE CABINETS
(ANY COMBINATION)
519005191051920
519005191051920
24W 24W
5190341489
48W
60" BASE CABINET ORTWO 30" BASE CABINETS
(ANY COMBINATION)
519015191151921
519015191151921
30W 30W
41489
60W
TWO 36" BASE CABINETS 0RTHREE 24" BASE CABINETS
(ANY COMBINATION)
519005191051920
24W
519005191051920
24W
519005191051920
24W36W
519025191251922
36W
519025191251922
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
BASE CABINET OFFERING (DETAILS ON PAGES 19-20)
36W
51902 51912 51922
30W
51901 51911 5192151900 51910
24W
51920
48W
51903 41489 41489
60W
8 1 .217.857.710012/20
GEN
CONSTRUCTION FEATURES• Solid galvanized frame construction allows
disassembly for constricted installation access areas• Powder coat exterior finishes• Shaft drive sashes with interlocks• Polyresin liner• LED light fixture• Stainless steel full width finger lift sashes, front
and back• Security sash locks• 18" open sash stop• 10" exhaust duct collar
STANDARD EQUIPMENT (factory installed)• 2 GFI duplex• Blower switch• Light switch• Cup sink• Remote cold water faucet• Remote gas fixture• Black epoxy 1/4" dish top
FACTORY-INSTALLED ADDS• 52005 Airflow monitor• 52006 Digital airflow monitor• 52007 External vacuum breaker
OPTION ACCESSORIES• 52001 Ceiling enclosure• 52004 Lattice assembly
51820 STYLEDemonstration hood has front and rear access vertical sashes. Ideal for rear see-thru demonstration viewing. Sashes have interlock, preventing simultaneous opening of both sashes. Ideal for stand-alone use where both viewing and experiment participation is desired. Unit also ideal for in-wall installation: student from classroom side and instructor operation from a more secure prep room area. GEN II hood includes additional rear sash lock to secure access into storage prep areas. Hood incorporates both by-pass and airfoil features.
The GEN II design has contour form vertical side posts and slope back header with radius lower horizontal edge. Design promotes smooth airflow into hood opening. Hood fascia has 36" high clear sight view. Full opening 29" sash ideal for unrestricted equipment setup access. Advantage Scientific hood includes standard 18" vertical sash stops to promote efficient working extraction and face velocity.
3 models available: 51820485632: 48"W x 56"H x 32 1/4"D 51820605632: 60"W x 56"H x 32 1/4"D 51820725632: 72"W x 56"H x 32 1/4"D
Demonstration GEN IIFront/Rear Sash
FUME HOODS
Same as 51820, with additional remote air fixture and remote vacuum fixture.3 models available: 51821485632: 48"W x 56"H x 32 1/4"D 51821605632: 60"W x 56"H x 32 1/4"D 51821725632: 72"W x 56"H x 32 1/4"D
51821 STYLE
MUST BE ORDERED WITH FUME HOOD. NOT SOLD SEPARATELY.52005 Factory-Installed Airflow Monitor (details on page 22)52006 Factory-Installed Digital Airflow Monitor (details on page 22)52007 Factory-Installed External Vacuum Breaker (as required by specific local, city or state codes)
FACTORY-INSTALLED ADDS
SashExtendsAbove
12"
36.50"
29"MaxSash
Opening
20"
36"
57.25"
3.875" 3.875"
17.75"
29"
RemovableAccessPanels
SashInterlock
10" Dia.SS Duct
18.25"
9ADVANTAGE-SCIENTIFIC.COM12/20
Demonstration GEN IIFront/Rear Sash
FUME HOODS
51820485632 / 51821485632
51820605632 / 51821605632
51820725632 / 51821725632
W H DSuperstructure: 48 56 321⁄4Worktop: 48 11⁄4 30Hood Opening: 38 29Hood View: 38 36
Exhaust Parameters: 739 CFM .26 SPHood Weight: 200 pounds (approx.)
W H DSuperstructure: 60 56 321⁄4Worktop: 60 11⁄4 30Hood Opening: 50 29Hood View: 50 36
Exhaust Parameters: 972 CFM .32 SPHood Weight: 225 pounds (approx.)
W H DSuperstructure: 72 56 321⁄4Worktop: 72 11⁄4 30Hood Opening: 62 29Hood View: 62 36
Exhaust Parameters: 1206 CFM .41 SPHood Weight: 270 pounds (approx.)
BASE CABINETS(SEE OFFERING BELOW)
48" BASE CABINET ORTWO 24" BASE CABINETS
(ANY COMBINATION)
519005191051920
519005191051920
24W 24W
5190341489
48W
60" BASE CABINET ORTWO 30" BASE CABINETS
(ANY COMBINATION)
519015191151921
519015191151921
30W 30W
41489
60W
TWO 36" BASE CABINETS 0RTHREE 24" BASE CABINETS
(ANY COMBINATION)
519005191051920
24W
519005191051920
24W
519005191051920
24W36W
519025191251922
36W
519025191251922
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
BASE CABINET OFFERING (DETAILS ON PAGES 19-20)
36W
51902 51912 51922
30W
51901 51911 5192151900 51910
24W
51920
48W
51903 41489 41489
60W
10 1 .217.857.710012/20
GEN
CONSTRUCTION FEATURES• Solid galvanized frame construction allows
disassembly for constricted installation access areas• Full view safety glass back• Powder coat exterior finishes• Shaft drive sash• LED light fixture• Stainless steel full width finger lift sash• 18" open sash stop• 10" exhaust duct collar
STANDARD EQUIPMENT (factory installed)• 2 GFI duplex• Blower switch• Light switch• Cup sink• Remote cold water faucet• Remote gas fixture• Black epoxy 1/4" dish top
FACTORY-INSTALLED ADDS• 52005 Airflow monitor• 52006 Digital airflow monitor• 52007 External vacuum breaker
OPTION ACCESSORIES• 52001 Ceiling enclosure• 52004 Lattice assembly
51825 STYLEStudent workstation hood is designed for front face vertical sash operation and 3-side viewing (both ends and back). A high performance hood, ideal as stand-alone application. Workstation hoods can be placed back-to-back (double face) and also end-to-end, forming island or peninsula arrangements. Great multi-use in a high participation laboratory setting.
The GEN II design allows use as a single- or multi-unit exhaust blower setup. Hood fascia has 42" high clear sight view. Blower and airflow balancing required by HVAC contractor.
3 models available: 51825486032: 48"W x 60"H x 32 3/8"D 51825606032: 60"W x 60"H x 32 3/8"D 51825726032: 72"W x 60"H x 32 3/8"D
Student Workstation GEN IIStand-Alone or Multi-Unit
FUME HOODS
FIXED REAR VIEW WINDOW
3-SidedViewing,
Each Unit
BACK-TO-BACK ISLAND OR PENINSULASTAND-ALONE
4-SidedViewing
THRU-WALL
Instructor/Prep Room
Side
ClassroomSide
Wall
3-SidedViewing
BackWall
AGAINST WALL
Same as 51825, with additional remote air fixture and remote vacuum fixture.3 models available: 51826486032: 48"W x 60"H x 32 3/8"D 51826606032: 60"W x 60"H x 32 3/8"D 51826726032: 72"W x 60"H x 32 3/8"D
51826 STYLE
MUST BE ORDERED WITH FUME HOOD. NOT SOLD SEPARATELY.52005 Factory-Installed Airflow Monitor (details on page 22)52006 Factory-Installed Digital Airflow Monitor (details on page 22)52007 Factory-Installed External Vacuum Breaker (as required by specific local, city or state codes)
FACTORY-INSTALLED ADDS
11ADVANTAGE-SCIENTIFIC.COM12/20
Student Workstation GEN IIStand-Alone or Multi-Unit
FUME HOODS
W H DSuperstructure: 48 60 323⁄8Worktop: 48 11⁄4 29Hood Opening: 453⁄8 29
Exhaust Parameters: 770 CFM .24 SPShipping Weight: 400 pounds (approx.)(hood only)
W H DSuperstructure: 60 60 323⁄8Worktop: 60 11⁄4 29Hood Opening: 573⁄8 29
Exhaust Parameters: 1000 CFM .30 SPShipping Weight: 480 pounds (approx.)(hood only)
W H DSuperstructure: 72 60 323⁄8Worktop: 72 11⁄4 29Hood Opening: 693⁄8 29
Exhaust Parameters: 1250 CFM .39 SPShipping Weight: 560 pounds (approx.)(hood only)
51825486032 / 51826486032
51825606032 / 51826606032
51825726032 / 51826726032
BASE CABINETS(SEE OFFERING BELOW)
48" BASE CABINET ORTWO 24" BASE CABINETS
(ANY COMBINATION)
519005191051920
519005191051920
24W 24W
5190341489
48W
60" BASE CABINET ORTWO 30" BASE CABINETS
(ANY COMBINATION)
519015191151921
519015191151921
30W 30W
41489
60W
TWO 36" BASE CABINETS 0RTHREE 24" BASE CABINETS
(ANY COMBINATION)
519005191051920
24W
519005191051920
24W
519005191051920
24W36W
519025191251922
36W
519025191251922
OF 10" DIA.EXHAUST DUCT
CL
OF 10" DIA.EXHAUST DUCT
CL
OF 10" DIA.EXHAUST DUCT
CL
BASE CABINET OFFERING (DETAILS ON PAGES 19-20)
36W
51902 51912 51922
30W
51901 51911 5192151900 51910
24W
51920
48W
51903 41489 41489
60W
12 1 .217.857.710012/20
GEN
CONSTRUCTION FEATURES• Solid galvanized frame construction allows
disassembly for constricted installation access areas• Powder coat exterior finishes• Shaft drive sash• Polyresin liner• LED light fixture• Stainless steel full width finger lift sash• 10" exhaust duct collar• Secondary containment trough
STANDARD EQUIPMENT (factory installed)• 2 GFI duplex• Blower switch• Light switch• Cup sink• Remote cold water faucet• Remote gas fixture• Black epoxy 1/4" dish top
FACTORY-INSTALLED ADDS• 52005 Airflow monitor• 52006 Digital airflow monitor• 52007 External vacuum breaker
OPTION ACCESSORIES• 52001 Ceiling enclosure• 52004 Lattice assembly
51830 STYLEADA (Americans with Disabilities Act) high performance hood for constant volume extraction blower (not included). Hood incorporates both by-pass and airfoil with retainer spill trough to protect wheelchair users. Cup sink and remote lever control fixtures are positioned forward and lower within ADA specifications.
The GEN II design has contour form vertical side posts and slope back header with radius lower horizontal edge. Design promotes smooth airflow into hood opening. Hood fascia has 36" high clear sight view. Full opening 29" sash ideal for unrestricted equipment setup access. Advantage Scientific hood includes standard 18" vertical sash stops to promote efficient working extraction and face velocity.
3 models available: 51830485632: 48"W x 56"H x 32 1/4"D 51830605632: 60"W x 56"H x 32 1/4"D 51830725632: 72"W x 56"H x 32 1/4"D
ADA GEN IIVertical Sash
FUME HOODS
Same as 51830, with additional remote air fixture and remote vacuum fixture.3 models available: 51831485632: 48"W x 56"H x 32 1/4"D 51831605632: 60"W x 56"H x 32 1/4"D 51831725632: 72"W x 56"H x 32 1/4"D
51831 STYLE
MUST BE ORDERED WITH FUME HOOD. NOT SOLD SEPARATELY.52005 Factory-Installed Airflow Monitor (details on page 22)52006 Factory-Installed Digital Airflow Monitor (details on page 22)52007 Factory-Installed External Vacuum Breaker (as required by specific local, city or state codes)
FACTORY-INSTALLED ADDS
OF EXHAUST DUCT
CL
33.75"
10"
20"
36"29"MaxSash
Height
57.25"
24.50"
1.25"30"
48"
10" Dia.SS Duct Collar
13ADVANTAGE-SCIENTIFIC.COM12/20
ADA GEN IIVertical Sash
FUME HOODS
51830485632 / 51831485632
51830605632 / 51831605632
51830725632 / 51831725632
W H DSuperstructure: 48 56 321⁄4Worktop: 48 11⁄4 30Hood Opening: 38 29Hood View: 38 36
Exhaust Parameters: 739 CFM .26 SPHood Weight: 200 pounds (approx.)
W H DSuperstructure: 60 56 321⁄4Worktop: 60 11⁄4 30Hood Opening: 50 29Hood View: 50 36
Exhaust Parameters: 972 CFM .32 SPHood Weight: 225 pounds (approx.)
W H DSuperstructure: 72 56 321⁄4Worktop: 72 11⁄4 30Hood Opening: 62 29Hood View: 62 36
Exhaust Parameters: 1206 CFM .41 SPHood Weight: 270 pounds (approx.)
BASE CABINETS(SEE PAGE 19 FOR DETAILS)
51931
51932
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
51930
14 1 .217.857.710012/20
GEN
CONSTRUCTION FEATURES• Solid galvanized frame construction allows
disassembly for constricted installation access areas• Powder coat exterior finishes• Shaft drive sash• Polyresin liner• LED light fixture• Stainless steel full width finger lift sash• Vertical sash with horizontal sliding panes• 10" exhaust duct collar• Secondary containment trough
STANDARD EQUIPMENT (factory installed)• 2 GFI duplex• Blower switch• Light switch• Cup sink• Remote cold water faucet• Remote gas fixture• Black epoxy 1/4" dish top
FACTORY-INSTALLED ADDS• 52005 Airflow monitor• 52006 Digital airflow monitor• 52007 External vacuum breaker
OPTION ACCESSORIES• 52001 Ceiling enclosure• 52004 Lattice assembly
51835 STYLEADA (Americans with Disabilities Act) high performance hood for constant volume extraction blower (not included). Hood incorporates both by-pass and airfoil with retainer spill trough to protect wheelchair users. Cup sink and remote lever control fixtures are positioned forward and lower within ADA specifications. Combination sash with sliding door panels in vertical frame sash. Combination sash allows vertical sash to be down while sliding door panel may be opened for access, reducing open exposure to hood interior as added safety feature.
The GEN II design has contour form vertical side posts and slope back header with radius lower horizontal edge. Design promotes smooth airflow into hood opening. Hood fascia has 36" high clear sight view. Full opening 29" sash ideal for unrestricted equipment setup access. Advantage Scientific hood includes standard 18" vertical sash stops to promote efficient working extraction and face velocity.
3 models available: 51835485632: 48"W x 56"H x 32 1/4"D 51835605632: 60"W x 56"H x 32 1/4"D 51835725632: 72"W x 56"H x 32 1/4"D
ADA GEN IICombination SashFUME HOODS
Same as 51835, with additional remote air fixture and remote vacuum fixture.3 models available: 51836485632: 48"W x 56"H x 32 1/4"D 51836605632: 60"W x 56"H x 32 1/4"D 51836725632: 72"W x 56"H x 32 1/4"D
51836 STYLE
MUST BE ORDERED WITH FUME HOOD. NOT SOLD SEPARATELY.52005 Factory-Installed Airflow Monitor (details on page 22)52006 Factory-Installed Digital Airflow Monitor (details on page 22)52007 Factory-Installed External Vacuum Breaker (as required by specific local, city or state codes)
FACTORY-INSTALLED ADDS
OF EXHAUST DUCT
CL
33.75"
10"
20"
36"29"MaxSash
Height
57.25"
24.50"
1.25"30"
48"
10" Dia.SS Duct Collar
15ADVANTAGE-SCIENTIFIC.COM12/20
ADA GEN IICombination SashFUME HOODS
51835485632 / 51836485632
51835605632 / 51836605632
51835725632 / 51836725632
W H DSuperstructure: 48 56 321⁄4Worktop: 48 11⁄4 30Hood Opening: 38 29Hood View: 38 36
Exhaust Parameters: 739 CFM .26 SPHood Weight: 200 pounds (approx.)
W H DSuperstructure: 60 56 321⁄4Worktop: 60 11⁄4 30Hood Opening: 50 29Hood View: 50 36
Exhaust Parameters: 972 CFM .32 SPHood Weight: 225 pounds (approx.)
W H DSuperstructure: 72 56 321⁄4Worktop: 72 11⁄4 30Hood Opening: 62 29Hood View: 62 36
Exhaust Parameters: 1206 CFM .41 SPHood Weight: 270 pounds (approx.)
BASE CABINETS(SEE PAGE 19 FOR DETAILS)
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
51931
51932
51930
16 1 .217.857.710012/20
GEN
CONSTRUCTION FEATURES• Galvanized frame construction• Powder coat exterior finishes• Polyresin liner• LED light fixture• Full width finger lift sash• 10" exhaust duct collar
STANDARD EQUIPMENT (factory installed)• 2 GFI duplex• Blower switch• Light switch• Cup sink• Remote cold water gooseneck faucet• Remote gas fixture• Black epoxy 1/4" dish top
FACTORY-INSTALLED ADDS• 52005 Airflow monitor• 52006 Digital airflow monitor• 52007 External vacuum breaker
OPTION ACCESSORY• 52001 Ceiling enclosure
51800 STYLEBy-pass fume hood. Value and performance in a solid design mounted on a flat epoxy top. Unit has a 29" high opening sash and is equipped with convenient remote operated fixtures.
2 models available: 51800485630: 48"W x 56"H x 29 1/2"D 51800605630: 60"W x 56"H x 29 1/2"D
Basic GEN IIBy-Pass
FUME HOODS
MUST BE ORDERED WITH FUME HOOD. NOT SOLD SEPARATELY.52005 Factory-Installed Airflow Monitor (details on page 22)52006 Factory-Installed Digital Airflow Monitor (details on page 22)52007 Factory-Installed External Vacuum Breaker (as required by specific local, city or state codes)
FACTORY-INSTALLED ADDS
SashExtendsAbove
5"
GasketedAccessPanels
SingleWeight
Counter-Balance
29"MaxSash
Opening
25"
48"
31"
0.5"
1.25" 9"
30"
56"
10" Dia.SS Duct
2-Tube Vapor SealedLED Light
10"
29.50"
17ADVANTAGE-SCIENTIFIC.COM12/20
Basic GEN IIBy-Pass
FUME HOODS
W H DSuperstructure: 48 56 291⁄ 2Worktop: 48 11⁄4 30Hood Opening: 43 29Hood View: 43 36
Exhaust Parameters: 833 CFM .33 SPHood Weight: 175 pounds (approx.)
W H DSuperstructure: 60 56 291⁄ 2Worktop: 60 11⁄4 30Hood Opening: 55 29Hood View: 55 36
Exhaust Parameters: 1100 CFM .34 SPHood Weight: 200 pounds (approx.)
51800485630
51800605630
OF EXHAUST DUCT
CL
JUNCTIONBOX
OF EXHAUST DUCT
CL
JUNCTIONBOX
BASE CABINETS(SEE OFFERING BELOW)
48" BASE CABINET ORTWO 24" BASE CABINETS
(ANY COMBINATION)
519005191051920
519005191051920
24W 24W
5190341489
48W
60" BASE CABINET ORTWO 30" BASE CABINETS
(ANY COMBINATION)
519015191151921
519015191151921
30W 30W
41489
60W
BASE CABINET OFFERING (DETAILS ON PAGES 19-20)
30W
51901 51911 5192151900 51910
24W
51920
41489
60W48W
51903 41489
18 1.217.857.710012/20
GEN
STANDARD EQUIPMENT (factory installed)• Interactive programmable alarm
system (reminder for saturation testing)
• Pressurized detection chamber (manually detect fi lter saturation)
• Internal fl uorescent light (tubular 18W, 500 Lux IP68)
• Painted steel construction• 6 ft. power cord
OPTION ACCESSORY• 52008 Particulate (HEPA) fi lter
52050 STYLEThe GEN II ductless portable fume hood – complete with mobile cart base – is for chemical and powder applications. Designed for applications where a fume hood is imperative, and versatility is a necessity. The fan/fi lter housing and control panel sit atop a fully welded tube chamber with plexiglass windows for viewing from all four sides. The front has a fold up door to allow for easy loading and unloading of apparatus and experiments.
One fi lter will handle the majority of chemicals, but the stackable fi lter system allows for multiple fi ltration confi gurations.
Available fi lters:• AS For solvents• BE+ For solvents and acids• F For formaldehydes• K For ammonia• H14 For powders
1 model available: 52050347728: 33 1/2"W x 76 1/2"H x 28"D
Portable HoodFUME HOODS
Duct
less
Por
tabl
e Fu
me
Hood
POWER ON/OFF SWITCH LOCATED ON SIDE OF UNIT
FLAT EPOXY RESIN
COUNTERTOP
CASTERSw/BRAKES
HINGED 1/4” CLEAR PLEXIGLASS PANEL
FRONT CONTROL PAD FOR FAN
AND LIGHT
24”
76 1/2”
71 1/4”
31 1/2”
33 1/2”
30” 36”
DOOR STAYS OPEN AT 150°
METAL ENCLOSURE AROUND FAN AND FILTER HOUSING
6 FTPOWERCORD
1/4” CLEAR PLEXIGLASS PANELS AT SIDES AND REAR
TUBING BASE FRAME
FAN
FILTER
LIGHT
19 1/8”
16 1/2”
25 1/2”
9 1/2”
1”1”
24”
24”
28”
8”
specifications
FRONT VIEW END VIEW
END USER QUESTIONNAIRE INFORMATION REQUIRED TO PROVIDE CORRECT FILTER MEDIA.
52008 Particulate (HEPA) Filter
OPTION ACCESSORY
19ADVANTAGE-SCIENTIFIC.COM12/20
Base CabinetsFUME HOODS
51900
41489
51901
51902
51903
W : 24 H : 35 D : 24
• Powder Coated Steel Construction
• Right Hinge Door with Full Access Opening
• Open Back• Adjustable Shelf
W : 48, 60 H : 35 D : 24, 29
• Laminated Wood Construction
• False Front• Doors• Removable Back
W : 30 H : 35 D : 24
• Powder Coated Steel Construction
• Double Doors with Full Access Opening
• Open Back• Adjustable Shelf
W : 36 H : 35 D : 24
• Powder Coated Steel Construction
• Double Doors with Full Access Opening
• Open Back• Adjustable Shelf
W : 48 H : 35 D : 24
• Powder Coated Steel Construction
• Double Doors with Full Access Opening
• Open Back• Adjustable Shelf
STANDING HEIGHTBASE CABINET
STANDING HEIGHTBASE CABINET
STANDING HEIGHTBASE CABINET
STANDING HEIGHTBASE CABINET
STANDING HEIGHTBASE CABINET
Actual: 24"W x 34 3/4"H x 22 3/8"D
Actual: 30"W x 34 3/4"H x 22 3/8"D
Actual: 36"W x 34 3/4"H x 22 3/8"D
Actual: 48"W x 34 3/4"H x 22 3/8"D
51932
51931
51930
W : 72 H : 32 D : 24
• Powder Coated Steel Construction
• Left and Right Hand Chases
• Open Design Allows Wheelchair Access
W : 60 H : 32 D : 24
• Powder Coated Steel Construction
• Left and Right Hand Chases
• Open Design Allows Wheelchair Access
W : 48 H : 32 D : 24
• Powder Coated Steel Construction
• Right Hand Chase• Open Design Allows
Wheelchair Access
ADA HEIGHTBASE CABINET
ADA HEIGHTBASE CABINET
ADA HEIGHTBASE CABINET
Actual: 48"W x 28 3/4"H x 22 3/8"D
Actual: 60"W x 28 3/4"H x 22 3/8"D
Actual: 72"W x 28 3/4"H x 22 3/8"D
20 1.217.857.710012/20
Base/Mobile CabinetsFUME HOODS
51910 51920
51911 51921
51912 51922
W : 24 H : 35 D : 18
• Vented Right Hinge Door• Reinforced Steel with Hi-
Tech Performance Polymer Alloy Coating Which Provides 100% Coverage Against Corrosion
• 3-Point Locking System• Vent Kit Provided
W : 24 H : 35 D : 18
• Right Hinge Door• 3-Point Locking System• Certifi ed to Meet NFPA 45
W : 30 H : 35 D : 18
• Vented Double Doors• Reinforced Steel with Hi-
Tech Performance Polymer Alloy Coating Which Provides 100% Coverage Against Corrosion
• 3-Point Locking System• Vent Kit Provided
W : 30 H : 35 D : 18
• Double Doors• 3-Point Locking System• Certifi ed to Meet NFPA 45
W : 36 H : 35 D : 18
• Vented Double Doors• Reinforced Steel with Hi-
Tech Performance Polymer Alloy Coating Which Provides 100% Coverage Against Corrosion
• 3-Point Locking System• Vent Kit Provided
W : 36 H : 35 D : 18
• Double Doors• 3-Point Locking System• Certifi ed to Meet NFPA 45
STANDING HEIGHTCORROSIVES BASE CABINET
STANDING HEIGHTCORROSIVES BASE CABINET
STANDING HEIGHTCORROSIVES BASE CABINET
STANDING HEIGHTFLAMMABLES BASE CABINET
STANDING HEIGHTFLAMMABLES BASE CABINET
STANDING HEIGHTFLAMMABLES BASE CABINET
Actual: 24"W x 34 3/4"H x 18 3/8"D Actual: 24"W x 34 3/4"H x 18 3/8"D
Actual: 30"W x 34 3/4"H x 18 3/8"D Actual: 30"W x 34 3/4"H x 18 3/8"D
Actual: 36"W x 34 3/4"H x 18 3/8"D Actual: 36"W x 34 3/4"H x 18 3/8"D
51940 W : 36 H : 29 D : 18
• 3-Point Locking System• 3" Casters
FLAMMABLESMOBILE CABINET
Actual: 36"W x 28 3/4"H x 18 3/8"D
21ADVANTAGE-SCIENTIFIC.COM12/20
52001 SERIESCEILING ENCLOSURES
52004 SERIESLATTICE ASSEMBLIES
The 52001 Series Ceiling Enclosures provide a professional, finished design in any setting. Ceiling enclosures are fabricated of cold rolled steel and finished to match the fume hood superstructure. Ceiling enclosures extend from top of hood to ceiling height or soffit.
To specify, provide model number and size of hood, plus floor-to-ceiling or floor-to-soffit dimension.
The 52004 Series Lattice Assemblies consist of 1/2" diameter aluminum apparatus rods with side mounting plates and cross clamps.
Lattice assembly may be added to hood in field when not ordered with hood.
To specify, provide model number and size of hood.
AccessoriesFUME HOODS
STEP #1: ATTACH ENCL ANGLES TO WALL ANDATTACH END ENCLOSURES TO TOP OF FUME HOOD
STEP #2: TILT BACK TOP OF FRONT ENCL TOWARD ENDENCL AND INSERT TOP CLIP (DETAIL A) INTO TOP SLOT(DETAIL C) ON END ENCL. PUSH BOTTOM OF FRONTENCL IN SO BOTTOM CLIP (DETAIL B) OF THE FRONTENCL FITS INTO BOTTOM SLOT (DETAIL D) ON END ENCLAND PUSH DOWN.
DETAIL C
DETAIL D
DETAIL A
DETAIL B
HEIGHT REQ’DBY SPEC
WIDTH OFFUME HOOD
33.750
CEILINGENCLOSURES
LATTICEASSEMBLIES
CEILING ENCLOSUREASSEMBLY DETAIL
22 1 .217.857.710012/20
Air Master Systems Corp. • 231.798.1111 • airmastersystems.com
33
Air Monitor AlarmsAFA 500 MK3 FUME HOOD AIRFLOW MONITOR
AFA 1000/1 MK3 FUME HOOD AIRFLOW MONITOR
Alarm Range 30-400 fpm (.15 - 2.0 m/s)
Accuracy Face velocity accuracy +/- 10%
Airflow Sensor On-board or remote sensor
Calibration Single or 2-point (Installer Selectable)
Low Air Alarm Delay Fixed 5 seconds
Relay Output 1 --( Low Air Alarm)
Analog Output Not Available
Relay Input 2 - Night setback andsash high
Comm. Port RS232 - Can be connected via serial interface to LAN network (Full hood performance software reporting available)
Sash Heigh Indication Yes - using a micro switch or Proximity switch input. With repeat alarm feature factory set to 5 minutes. (Can be adjusted via laptop up to 30 min.)
Night Setback Yes - using a relay input
External Alarm Indication Not available
Power Requirement Input - 120VAC, 60Hz / Output - 15VDC, 500ma
Display - Visual LED: red, alarm; green, normal
Alarm Indication Red LED and audible alarm
Horn Silence Yes - temporary
Mounting Semi Flush
Operating Temperature 55-86 F (13-30 C)
Storage Temperature -40-150 F (-40-65 C)
Instrument Dimensions Instrument Case: 5.2” H x 3.19” W x 1.97” D (132mm H x 81mm W x 50mm D)
Agency Listings UL and CE
Display Range 0-999 fpm (0 - 5.0 m/s)
Alarm Range 0-999 fpm (0 - 5.0 m/s)
Field Set-Up 2-point velocity calibration ( with on-screen instructions )
Accuracy Sensor / Display Resolution 1 fpm / Face Velocity Accuracy +/-10%
Alarm Delays User Configurable - 0 to 60 seconds
Relay Output 4 ( 1 on board - 3 on optinal plug in relay interface unit )
Analog Output 0-10V Output, Directly proportional to velocity (Optional)
Relay Input 3
Comm. Port RS232 - Can be connected via Serial Interface to LAN network ( Full Software Available)
Sash High Indication Yes, with separate plug-in connection
Night Setback Yes
External Alarm Indication Yes
Power Requirement Input-120VAC, 60Hz
Units Output-15VDC, 500ma
Display-Visual English and Metric (user selectable)
Alarm Indication Analog bar graph or Fault Timeline / LEDs: red, alarm; yellow, caution; green, normal / Digital display of velocity reading (can be turned off)
Horn Silence Yes (temporary / permanent / automatic depending on type of alarm or external input)
Mounting Semi Flush
Operating Temperature 55-86 F ( 13-30 C )
Storage Temperature -40-150 F (-40-65 C )
Instrument Dimensions Instrument Case: 5.2” H x 3.19” W x 1.14” D ( 132mm H x 81mm W x 29mm D )
Agency Listings UL and CE
Air Master Systems Corp. • 231.798.1111 • airmastersystems.com
33
Air Monitor AlarmsAFA 500 MK3 FUME HOOD AIRFLOW MONITOR
AFA 1000/1 MK3 FUME HOOD AIRFLOW MONITOR
Alarm Range 30-400 fpm (.15 - 2.0 m/s)
Accuracy Face velocity accuracy +/- 10%
Airflow Sensor On-board or remote sensor
Calibration Single or 2-point (Installer Selectable)
Low Air Alarm Delay Fixed 5 seconds
Relay Output 1 --( Low Air Alarm)
Analog Output Not Available
Relay Input 2 - Night setback andsash high
Comm. Port RS232 - Can be connected via serial interface to LAN network (Full hood performance software reporting available)
Sash Heigh Indication Yes - using a micro switch or Proximity switch input. With repeat alarm feature factory set to 5 minutes. (Can be adjusted via laptop up to 30 min.)
Night Setback Yes - using a relay input
External Alarm Indication Not available
Power Requirement Input - 120VAC, 60Hz / Output - 15VDC, 500ma
Display - Visual LED: red, alarm; green, normal
Alarm Indication Red LED and audible alarm
Horn Silence Yes - temporary
Mounting Semi Flush
Operating Temperature 55-86 F (13-30 C)
Storage Temperature -40-150 F (-40-65 C)
Instrument Dimensions Instrument Case: 5.2” H x 3.19” W x 1.97” D (132mm H x 81mm W x 50mm D)
Agency Listings UL and CE
Display Range 0-999 fpm (0 - 5.0 m/s)
Alarm Range 0-999 fpm (0 - 5.0 m/s)
Field Set-Up 2-point velocity calibration ( with on-screen instructions )
Accuracy Sensor / Display Resolution 1 fpm / Face Velocity Accuracy +/-10%
Alarm Delays User Configurable - 0 to 60 seconds
Relay Output 4 ( 1 on board - 3 on optinal plug in relay interface unit )
Analog Output 0-10V Output, Directly proportional to velocity (Optional)
Relay Input 3
Comm. Port RS232 - Can be connected via Serial Interface to LAN network ( Full Software Available)
Sash High Indication Yes, with separate plug-in connection
Night Setback Yes
External Alarm Indication Yes
Power Requirement Input-120VAC, 60Hz
Units Output-15VDC, 500ma
Display-Visual English and Metric (user selectable)
Alarm Indication Analog bar graph or Fault Timeline / LEDs: red, alarm; yellow, caution; green, normal / Digital display of velocity reading (can be turned off)
Horn Silence Yes (temporary / permanent / automatic depending on type of alarm or external input)
Mounting Semi Flush
Operating Temperature 55-86 F ( 13-30 C )
Storage Temperature -40-150 F (-40-65 C )
Instrument Dimensions Instrument Case: 5.2” H x 3.19” W x 1.14” D ( 132mm H x 81mm W x 29mm D )
Agency Listings UL and CE
Factory-InstalledAccessories
FUME HOODS
52005 AIRFLOW MONITOR
52006 DIGITAL AIRFLOW MONITOR
AIRFLOW MONITORS ARE HIGHLY RECOMMENDED FOR USE AND MUST BE ORDERED FACTORY-INSTALLED.
NOT SOLD SEPARATELY.