imagination at work

IMMERSION™

LED Refrigerated Display Lighting

Center Mullion Lights48-inch: GELT404850CTR-SY/-SB (65602/65605), GELT404840CTR-SY/-SB (65608/65611), GELT404835CTR-SY/-SB (65614/65617)60-inch: GELT406035CTR-SY/-SB (79753/79756), GELT406040CTR-SY/-SB (79747/79750) & GELT406050CTR-SY/-SB (79741/79744)70-inch: GELT407035CTR-SY/-SB (79771/79774), GELT407040CTR-SY/-SB (79765/79768), GELT407050CTR-SY/-SB (79759/79762)

Description Code (Single Unit Product Number / 10-Pack Product Number)

Vertical CasesRV40 Series

GELighting

Retrofit Installation Guide

BEFORE YOU BEGINRead these instructions completely and carefully.

A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

B. Before servicing or cleaning unit, switch power off at the service paneland follow appropriate lock out/tag out safety procedures.

Risk of electrical shock. Disconnect power before servicing or installing product.LED Retrofit Kit Installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. Installthis kit only in the luminaires that have the construction features and dimensionsshown in the photographs and/or drawings. / Risque de choc électrique. Couperle courant avant de réparer ou installer le produit. LED Retrofit Kit d'installationnécessite la connaissance des systèmes luminaires électriques. Si vous n'êtespas qualifié, ne tentez pas l'installation. Contactez un électricien qualifié. Installezce kit seulement dans les luminaires qui ont les caractéristiques de constructionet les dimensions figurant sur les photographies et / ou des dessins.

WARNING / AVERTISSMENT

Risk of injury. While performing installations described, gloves, safety glasses or goggles should be worn. / Risque de blessure. Lors de l'exécutiondes installations décrites, des gants, des lunettes de sécurité ou des lunettesde protection doivent être portées.

CAUTION / ATTENTION

PREPARE ELECTRICAL WIRINGElectrical Requirements• The power supply must be supplied with 100-240 VAC, 50/60 Hz., and connected to an individual properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse.

• Wiring must be 2 wire with ground and rated for 75°C (167°F).• Do not overload driver, follow installation instructions for the GEPS4000NCMUL-SY.

• Ensure that all connection points are sealed for damp location using the appropriate method per the NEC or local electrical code.

Grounding Instructions–Cable Direct• This lighting system must be connected to a grounded metal, permanent wiring system, or an equipment grounding conductormust be run with the circuit conductors and be connected to the equipment grounding terminal.

FOR YOUR SAFETYRead and observe all CAUTIONS and WARNINGS shown throughout these instructions. • Installation to be performed by factory trained service personnel only.• For use inside a commercial refrigeration case with packaged foods only.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in acommercial environment. This equipment generates, uses, and can radiate radio frequen-cy energy and, if not installed and used in accordance with the instruction manual, maycause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will berequired to correct the interference at his own expense.

This Class [A] RFLD complies with the Canadian standard ICES-003. Ce DEFR de la classe[A] est conforme à la NMB-003 du Canada.

LED DRIVER COMPATIBILITYThis system is compatible with the GEPS4000NCMUL-SY. Please refer to the separate LED driver installation guide for appropriate wiring connections.

• For retrofit only. If you are an OEM, please refer to the OEM Installation Guide.

• Refer to manufacturing manual for refrigeration case to identify lighting control circuits. Ensure that power is switched off at the service panel for the lighting circuit. If a lighting power switch is not provided in the refrigeration case, power removal can be performed at the main breaker panel.

• Locate existing lighting components including ballasts, lampholders, lamps, and lampguards in the refrigeration case for removal. Please refer to refrigeration manual for any questions dealing with component locations.

• Remove lamps, lampholder and lamp guards. Cut the wiring,making the cut as close to the lampholder as possible. Do not remove wiring from case as it will be utilized to attach the LED light. Dispose of components per federal and local regulations.

• Locate ballast within system. The most common location is in the mullion or the electrical raceway found in the bottom of the refrigerated case.

• Disconnect ballast input and output connectors. Cut the ballast connector wires nearest to the connector and remove connector. Unscrew the mounting screws that attach ballast and remove ballast. Dispose of ballasts according to federal and local regulations. LED driver installation will begin at Step 5 and Step 6.

• To install the LED light, first identify the wiring for connectionto the LED driver. After removing the connector from ballast, leave the existing ballast input and output wires for reconnection in a later step.

Remove Existing Lighting Components1

2

Tools Required Components Required

LED light

LED driver

Wire cover

6-32 x 1/2" screws

Twist lock splice wire connectors

Wire stripper/cutter

Tape measure

Screwdriver

Cordless drill

Hammer

7/64-inch (2.8mm) drill bit

Center punch

4

5

6

7

3

2

1

4

5

3

2

1

1

23

45

Fluorescent Component Location

Lamp with lamp guards(behind mullion)

Lamp holders

Ballast1. Mullion2. Raceway3. Overhead door frame

A

B

C

A

B

B

C3

C1

C2

56 7

4

WARNING/AVERTISSEMENT

Les pièces et câbles électriques risquent d’être endommagés lors du perçage

• Measure the total width of the mullion, and mark a vertical line half the total width near the top and bottom of the mullion.

• Prepare for the upper end of the Center LED Light. Mark a horizontal line a minimum 2 1/8-inches (54 mm) from the topof the mullion, and another horizontal line 3/8-inch (10 mm) below this line.

• Prepare for the lower end of the Center LED Light. — For 48-inch LED Lights mark a horizontal line 46 1/4" (1175mm) beneath the first line drawn for the top Mounting.

— For 60-inch LED Lights, mark a horizontal line 58 3/32-inches (1476 mm) beneath the first line drawn for the top Mounting Tab.

— For 70-inch LED Lights, mark a horizontal line 68 15/32" (1739 mm) beneath the first line drawn for the top Mounting Tab.

• Center the center punch directly at the intersection of the horizontal lines and the vertical line (top and bottom) and establish a dimple.

• Use power drill and 7/64-inch (2.8 mm) drill bit to drill holes at the intersection of the vertical and horizontal center line.

Install Center LED Lights

Prepare for Installation of Center LED Lights

3

2of mullion

Total width

( 10 mm) 3/8"

For 60-inch LED Lights:58 3/32" (1476 mm)

Center punch at intersection

and drill a 7/64-inch (2.8 mm)

hole

mullion

Half total width of

LED Driver wires - top

For 70-inch LED Lights:68 15/32" (1739 mm)

• Place a Center LED Light against the back face of the mullion near the two holes drilled at the top.

• Insert a #6-32 x 1/2-inch sheet metal screw into the top slot of the Mounting Tab on the Center LED Light and intothe first hole that was drilled in the center mullion.

• Use a screwdriver to thread the screw into the drilled hole.

• Repeat for the second screw, and for the lower end of the Center LED Light.

• Refer to the manufacturing manual for door frame to ensure there are no components contained inside the mullion that could be drilled through. Use a #6 - 3/4-inch self-drilling screw to attach the Center LED Light into one or two of the additional drill through holes located near the center of the LED Light.

• Refer to wiring diagram on page 5. Connect the red and black output wires from the LED Light to the red and black wires on the LED Driver using the twist lock splice wire connectors provided.

Risk of electrical shock. Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not leaveany other open holes in an enclosure of wiring or electric components / Risque de choc électrique. Seuls les trous ouverts indiqués dans les photos et / ou lesdessins peuvent être faites ou modifiés à la suite du montage du kit. Ne pas laisser autres trous ouverts dans l'enceinte du câblage électrique ou composants.

WARNING / AVERTISSMENT

3

Mounting Tab

LED DriverLeads

Center LED Light Power Leads

For 48-inch LED Lights:46 1/4" (1175mm)

LED Driver wires - top

4

LED Driver Configuration Options

6-Door Case

5-Door Case 4-Door Case

For 48" LED Lights For 60" & 70" LED Lights

3-Door Case 2-Door CaseFor 60" & 70" LED LightsFor 48" LED Lights For 48", 60" & 70" LED Lights

For 60" & 70" LED LightsFor 48" LED LightsFor 48" LED Lights For 60" & 70" LED Lights

LEDDRIVER

The diagrams below represent wiring configurations for each LED Driver.

LEDDRIVER

LEDDRIVER

LEDDRIVER

LEDDRIVER

LEDDRIVER

LEDDRIVER

LEDDRIVER

LEDDRIVER

LEDDRIVER

Risk of injury. Do not overload LED Driver, 60-watts maximum per driver. For 48-inch LED Lights, do not exceed 4 Center LEDLights per LED driverloading limit. (2 End LED Lights is equivalent to 1 Center LED Light). For 60-inch LED Lights, do not exceed 3 Center LED Lights per LED driver. (2 EndLED Lights is equivalent to 1 Center LED light). For 70-inch LED Lights, do not exceed 2 Center LED Lights plus 1 End LED Light per LED driver loadinglimit. Risque de blessure. Ne pas surcharger le driver LED, 60-watts maximum par driver. Dans le cas des lampes LED de 48"-122 cm, ne pasdépasser 4 lampes LED centrales par limite de charge du driver. (2 lampes LED latérales équivalent à 1 lampe LED centrale). Dans le cas des lampesLED de 60"- 122 cm, ne pas dépasser 4 lampes LED centrales par limite de charge du driver. (2 lampes LED latérales équivalent à 1 lampe LED centrale). Dans le cas des lampes de 70"-175 cm, ne pas dépasser 2 lampes LED centrales et 1 lampe LED latérale par limite de charge de driver.

CAUTION / ATTENTION

LEDDRIVER

LEDDRIVER

LEDDRIVER

Center LED Lights 5 4 3 2 1

End LED Light Sets 1 1 1 1 1

LED Drivers (60-inch LED Lights) 2 2 2 1 1

LED Drivers (70-inch LED Lights) 3 2 2 2 1

LED Drivers (48-inch LED Lights 2 2 1 1 1

Wire Covers 7 6 5 4 3

Parts Needed Per Case6-Door 5-Door 4-Door 3-Door 2-Door

LEDDRIVER

LEDDRIVER

LEDDRIVERLED

DRIVERLED

DRIVERLED

DRIVER

TERMINAL BLOCK

LED DRIVER

WHITE (NEUTRAL)

BLACK (LINE)

SWITCH

B R B R

BW

B R

G

RIG

HT

END

LED

LIG

HT

LEFT

EN

D L

ED L

IGH

T

A

C

B

DOccupancy Sensor

Gray Purple

Risk of electrical shock. Ensure that all connection points are sealed for damp location using the appropriate method per the NEC or localelectrical code. Risque de choc électrique. S’assurer que les points de raccordements sont scellés pour emplacement humide en employantune méthode permise par le NEC ou par le code électrique local.

WARNING / AVERTISSMENT

One End Set (Right and Left) & One Center LED Light

One End LED Light (Right or Left) & One Center LED Light

TERMINAL BLOCK

LED DRIVER

WHITE (NEUTRAL)

BLACK (LINE)

SWITCH

B R B R

BW

B R

G

END

(R o

r L)

LED

LIG

HT

CEN

TER

LED

LIG

HT

A

C

B

DOccupancy Sensor

Gray Purple

TERMINAL BLOCK

LED DRIVER

WHITE (NEUTRAL)

BLACK (LINE)

SWITCH

B R

BW

B R

G

CEN

TER

LED

LIG

HT

A

C

B

B R

LEFT

EN

D L

ED L

IGH

T

B R

RIG

HT

END

LED

LIG

HT

DOccupancy Sensor

Gray Purple

Note: LED Lights are polarity insensitiveNote: LED Lights are polarity insensitive

TERMINAL BLOCK

LED DRIVER

WHITE (NEUTRAL)

BLACK (LINE)

SWITCH

B R

BW

B R

G

CEN

TER

LED

LIG

HT

A

C

B

DOccupancy Sensor

Gray Purple

TERMINAL BLOCK

LED DRIVER

WHITE (NEUTRAL)

BLACK (LINE)

SWITCH

B R B R

BW

B R

G

CEN

TER

LED

LIG

HT

CEN

TER

LED

LIG

HT

A

C

B

DOccupancy Sensor

Gray Purple

Two Center LED Lights One Center LED LightNote: LED Lights are polarity insensitive Note: LED Lights are polarity insensitive

One End Set (R & L) LED LightsNote: LED Lights are polarity insensitive

Connection Configurations4

5

For information on A, B, C, D, see Steps 5, 6, and 7.

B

C

B

C

B

C

B

C

B

C

C

TERMINAL BLOCK

(AC Source)

C

TERMINAL BLOCK

(AC Source)

C

TERMINAL BLOCK

(AC Source)

C

TERMINAL BLOCK

(AC Source)

C

TERMINAL BLOCK

(AC Source)

5

Connect LED Driver - Input

Connect LED Driver - Output

Connect Dimming Contacts – Output (Optional)

6

7

USING TWIST-ON WIRE CONNECTORThe LED Driver is required to be reliably bonded to the protective ground conductor.

Attach the supplied green/yellow ground wire from the LED Driver to a grounded metal portion of the door frame. Remove the 3-way connector from the LED Driver by cutting the wires near the connector and strip the input wires. Using

the appropriate wiring diagram on page 5, connect the original Line and neutral wires (or Line 1 and Line 2 wires for 240 nominal VAC) to the LED Driver leads using the provided twist lock splice wire connectors or other connection method approved for low temperature usage and stranded cable. (B)

• Make input (AC) connections as noted below:

• For Retrofit, place LED driver in the location where the ballast was formerly located.• Make output (DC) connections as noted below:

USING TWIST-ON WIRE CONNECTORSRemove the 4-way connector from the LED Driver by cutting the wires near the connector and strip the output leads. Using the appropriate wiring diagram on page 5, connect the LED Driver output leads to the LED Light leads. Use an ohm meter to identify the two wires connected to the LED Light that measure between ~ 15,000-18,000 ohms. Use wire connectors or other connection method approved for low temperature usage and stranded cable. (A)

For non-dimming applications, cap the unused wires with 5/32" (4mm) twist on wire connectors.

Bundle and safely secure any unused wires by way of approved wire ties and wire connectors.

USING TWIST-ON WIRE CONNECTORSRemove the 4-way connector from the LED Driver by cutting the wires near the connector and strip the output leads. Using the appropriate wiring diagram on page 5, connect the LED Driver dimming output leads to the occupancy sensor or control system using wire connectorsor other connection method approved for low temperature usage and stranded cable. (D)

• To enable dimming operation, connect leads from occupancy sensor or control system (normally open contact) to the purple and gray leads of the power supply.

• Make output (contact closure) connections using one of the two options below:

• The LED Driver is capable of step dimming from 100% power to 20% power when used with a normally open contact closure occupancy sensor system.

• When using the LED drivers for non-dimming applications, the dip switch setting must be set to #1 ON to disable the dimming feature and achieve 100% illumination.

6

A

C

D

B

LED Refigerated Display Lights – Cleaning Instructions

• The outer lens and the plastic housing should be cleaned periodically with a mild liquid dish detergent.

• Do not use chemical cleaners to clean the lens.

• Keep the outside clean. Wipe with a clean cloth lightly dampened with mild liquid dish detergent. Dry with a clean, soft cloth.

• Do not wipe the lens with a soiled dish cloth or wet towel. These may leave a residue that can damage the finish.

• Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and damage the finish.

13502-R110813

9

Attach Covers to Mounting Tab

• Tuck wires underneath Wire Cover before installing it ontothe End Cap.

• Attach Wire Cover to LED Light Mounting Tab by inserting a M2.9x10 pan head tapping screw (provided) through the holes in Covers and Mounting Tabs using an installation torque of 3 lbf-in.

NOTE: Tighten slowly until fully seated, do not over tighten or strip the threads.

WireCover

Mounting Tab

M2.9x10 panhead tappingscrew

Risk of electrical shock. Plastic cover is needed to protect electrical wires from tampering and accidental contact. / Risque de chocélectrique. Le couvercle en plastique est requis pour assurer une protection adéquate contre l'accès aux fils et les contacts accidentels.

CAUTION / ATTENTION

8

7

Risk of electrical shock. Disconnect power to LED Lights before any cleaning operation.Risque de choc électrique. Débranchez l'alimentation des éclairages à LED avant toute opération de nettoyage.

WARNING / AVERTISSMENT

GE Lighting Solutions • 1-888-MY-GE-LED • www.gelighting.com

1 - 8 8 8 - 6 9 - 4 3 - 5 3 3

GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. Immersion is a trademark of GE Lighting Solutions, LLC. The GE brand and logo are trademarks of the General Electric Company.© 2013 GE Lighting Solutions, LLC. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.

This product is intended solely for the use of commercial refrigerated, display or case lighting and is not intended for use inany other application.