+ All Categories
Home > Documents > GE Oil & Gas NTC€¦ · GE imagination at work GE Oil & Gas Specifications Flow Rate 15 – 300 US...

GE Oil & Gas NTC€¦ · GE imagination at work GE Oil & Gas Specifications Flow Rate 15 – 300 US...

Date post: 03-Aug-2020
Category:
Upload: others
View: 2 times
Download: 0 times
Share this document with a friend
2
GE imagination at work GE imagination at work GE Oil & Gas Specifications Flow Rate 15 – 300 US gpm (514-10,285 BPD or 82-1635 m 3 /D) Maximum Discharge Pressure 2500 psi (172 bar) (Application dependent rating) Max Shaft Horsepower (60Hz) Up to 75 HP (56 kW) Max Fluid Temperature 200°F (93°C) Housing Metallurgy Standard carbon steel Corrosion resistant options Stage Metallurgy Ni-resist Type 1 Maximum Suction PSI 260 psi (18 bar) @ 200°F (93°C) Typical System Lengths 6ft (1.8 m) - 21ft (6.4m) NTC Close-Coupled Surface Pumping System Compact design combined with lower upfront costs and minimal maintenance help maximize run time and minimize operating costs. The GE Oil & Gas Surface Pumping Systems No Thrust Chamber (NTC) model is the latest offering designed to meet the needs of an ever evolving, high demand market. Featuring a design that does not require a thrust chamber, the NTC has lower upfront cost and reduced system complexity to improve reliability. With flow rates ranging from 15 gpm to 300 gpm, the NTC can be configured for a wide range of applications, with higher output pressure than many alternative pump technologies. The NTC can also be configured with Abrasion Resistant bearings to further protect the system and increase run life.
Transcript
Page 1: GE Oil & Gas NTC€¦ · GE imagination at work GE Oil & Gas Specifications Flow Rate 15 – 300 US gpm (514-10,285 BPD or 82-1635 m3/D) Maximum Discharge Pressure 2500 psi (172 bar)

GE imagination at workGE imagination at work

GE Oil & Gas

Specifications

Flow Rate 15 – 300 US gpm(514-10,285 BPD or 82-1635 m3/D)

Maximum DischargePressure

2500 psi (172 bar)(Application dependent rating)

Max Shaft Horsepower (60Hz) Up to 75 HP (56 kW)

Max Fluid Temperature 200°F (93°C)

Housing Metallurgy Standard carbon steel Corrosion resistant options

Stage Metallurgy Ni-resist Type 1 Maximum Suction PSI 260 psi (18 bar) @ 200°F (93°C)Typical System Lengths 6ft (1.8 m) - 21ft (6.4m)

NTCClose-Coupled Surface Pumping SystemCompact design combined with lower upfront costs and minimal maintenance help maximize run time and minimize operating costs.

The GE Oil & Gas Surface Pumping Systems No Thrust Chamber(NTC) model is the latest offering designed to meet the needs of anever evolving, high demand market. Featuring a design thatdoes not require a thrust chamber, the NTC has lower upfront costand reduced system complexity to improve reliability. With flow ratesranging from 15 gpm to 300 gpm, the NTC can be configured for awide range of applications, with higher output pressure than manyalternative pump technologies. The NTC can also be configuredwith Abrasion Resistant bearings to further protect the system andincrease run life.

Page 2: GE Oil & Gas NTC€¦ · GE imagination at work GE Oil & Gas Specifications Flow Rate 15 – 300 US gpm (514-10,285 BPD or 82-1635 m3/D) Maximum Discharge Pressure 2500 psi (172 bar)

GE imagination at work

GE Oil & Gas

Note: These values are for pumps running at 3570rpm at 1 SG.

4425 Westway BlvdHouston, TX 77041 USA713 260 6740geoilandgas.com/sps

• Crude oil boosting/ transfer• Jet pumping• Lean amine circulation• Mine dewatering• Pipeline boosting

• Process fluids transfer• Produced water disposal• Produced water injection• LACT

Applications

• Low pump thrust eliminates need for thrust chamber

• Designed to be compact• Designed with rear pull-out seal• Standard C-Face, foot mounted NEMA frame

motors• Non pulsating flow

• Reduced maintenance, upfront costs, and less mechanical parts for repairs

• Small footprint reduces site space requirement and optimizes facility design

• Minimal downtime for mechanical seal maintenance or replacements

• Motor easily replaced

Features Benefits

5

SD0019SD0013 SD0025

SD0038

SE0230

SE0115

SE0080

SE0170

250

500

750

1000

1250

1500

1750

2000

2250

2500

2750

10 20 30 40 50 60 70 80 90 200100

Pres

sure

(psi

)

Flow (US gpm)

Performance for SD & SE Series Pumps

SE0052

SE0125

SD0052


Recommended