depth width
heig
ht
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
• Solid front and top glass heated• Sliding rear doors (600 model hinged)• Deck forced refrigeration• Double glazed• Three adjustable shelves• Ticket strips on shelves and base• Undershelf and canopy LED lights• Integral condenser• Plinth, castors and skirt• Self evaporating• Rear condenser air intake and extract
CABINET DIMENSIONS & SPECIFICATIONS
more information in service section
Refrigerated 4o factory set point
COSSIGA Packaging
• Honeycomb cardboard design • Specifically for glass cabinets• Environmentally friendly• No timber used ( certified ply base )• No hammers or crowbars required
Model Cabinet Shelving no. Shelf length base tray Total food
unitsDisplay
m2Refrig-erant
Operating Current
Connection Voltage Packed for Shipping
w x d 100 x 100 50/60Hz
Length mm
Depth mm
Height mm
Length mm
Depth mm
Height mm
Weight Kg
Cube
BTGRF6 600 750 1380 3 + base 495 x 445 540 x 510 80 0.94 134A 5.0Amp 10amp 3 pin plug 240V 700 830 1550 132 1.25
BTGRF9 900 750 1380 3 + base 795 x 445 840 x 510 128 1.50 134A 6.9Amp 10amp 3 pin plug 240V 1000 830 1550 195 1.29
BTGRF12 1200 750 1380 3 + base 1095 x 445 1140 x 510 187 2.06 134A 7.3Amp 10amp 3 pin plug 240V 1300 830 1550 220 1.68
BTGRF15 1500 750 1380 3 + base 1395 x 445 1440 x 510 238 2.60 134A 8.0Amp 10amp 3 pin plug 240V 1600 830 1550 245 2.0575
0
900
1200
BTG
RF6
600
1500
BTG
RF9
BTG
RF1
2
BTG
RF1
5
REFRIGERATED
445
1380
750710
550
20
35
25
770
20
750
BTGRF GLASS TOWER SERIES
9/12/2014 Page 1
depth width
heig
ht
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
• Solid front and top glass • Sliding rear doors (600 model hinged)• Deck forced heating• Single glazed • Four adjustable shelves• Ticket strips on shelves and base• Undershelf and canopy LED lights• Plinth, castors and skirt
CABINET DIMENSIONS & SPECIFICATIONS
more information in service section
Heated 75o factory set point
COSSIGA Packaging
• Honeycomb cardboard design • Specifically for glass cabinets• Environmentally friendly• No timber used ( certified ply base )• No hammers or crowbars required
Model Cabinet Shelving no.
Shelf length base tray Total food
unitsDisplay
m2Operating Current Connection Voltage Packed for Shipping
w x d 100 x 100 50/60Hz
Length mm
Depth mm
Height mm
Length mm
Depth mm
Height mm
Weight Kg
Cube
BTGHT6 600 750 1380 4 + base 495 x 445 540 x 510 100 1.16 7.2Amp 10amp 3 pin plug 240V 1000 830 1550 132 1.25
BTGHT9 900 750 1380 4 + base 795 x 445 840 x 510 160 1.86 7.2Amp 10amp 3 pin plug 240V 1000 830 1550 132 1.25
BTGHT12 1200 750 1380 4 + base 1095 x 445 1140 x 510 231 2.55 8.6Amp 10amp 3 pin plug 240V 1300 830 1550 167 1.68
GLASS TOWER SERIESBTGHT
1380
750710
550
20
35
25
770
20
750
445
750
900
1200
600
BTG
HT1
2
BTG
HT9
BTG
HT6
HEATED
9/12/2014 Page 2
depth width
heig
ht
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
• Solid front and top glass • Sliding rear doors• Circulating fan• Single glazed• Four adjustable shelves• Ticket strips on shelves and base• Undershelf and canopy LED lights• Plinth, castors and skirt
CABINET DIMENSIONS & SPECIFICATIONS
more information in service section
Ambient
COSSIGA Packaging
• Honeycomb cardboard design • Specifically for glass cabinets• Environmentally friendly• No timber used ( certified ply base )• No hammers or crowbars required
Model Cabinet Shelving no.
Shelf length base tray Total food
unitsDisplay
m2Operating Current Connection Voltage Packed for Shipping
w x d 100 x 100 50/60Hz
Length mm
Depth mm
Height mm
Length mm
Depth mm
Height mm
Weight Kg
Cube
BTGAB9 900 750 1380 4 + base 795 x 445 840 x 510 160 1.86 1.21 Amp 10amp 3 pin plug 240V 1300 830 1550 167 1.68
BTGAB12 1200 750 1380 4 + base 1095 x 445 1140 x 510 231 2.55 1.21Amp 10amp 3 pin plug 240V 1300 830 1550 167 1.68
GLASS TOWER SERIESBTGAB
1380
750710
550
20
35
25
770
20
750
445
750
900
1200
BTG
AB
12
BTG
AB
9
AMBIENT
9/12/2014 Page 3
SERVICES REQUIRMENTSBTGRF GLASS TOWER SERIES
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
GLASS TOWER BTGRF - Chilled Unit ServicesStand Alone Refrigerated Unit With Covers
750
305
400
95
705
150
445
195
45 4545
600 ~ 1500
GLASS
445
1380
750710
550
20
35
25
770
20
750
Maximum ambient operating temperature climate class N max 32˚C
Removable rear stainless steel cover for service
Clean condenser face at two weekly intervals
ELECTRICAL POWER
Electrical power cord 1500mm long All units 3 pin 10 amp 1 phase
REAR VIEW REAR VIEW RF600 HINGED DOORS
9/12/2014 Page 4
SERVICES REQUIRMENTSBTGHT GLASS TOWER SERIES
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
GLASS TOWER BTGHT - HEATED Unit ServicesStand Alone Unit With Covers
750
195
45 4545
600 ~ 1200
GLASS
1380
750710
550
20
35
25
770
20
750
445
305
400
95705
150
ELECTRICAL POWER
- Electrical power cord 1500mm long- All units 3 pin 10 amp 1 phase
Electrical box accessed from side withside panel removed
REAR VIEW REAR VIEW HT600 HINGED DOORS
9/12/2014 Page 5
GLASS TOWER BTGAB - AMBIENT Unit ServicesStand Alone Unit With Covers
750
195
45 4545
900 ~ 1200
GLASS
1380
750710
550
20
35
25
770
20
750
445
305
400
705
150
SERVICES REQUIRMENTSBTGAB GLASS TOWER SERIES
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
ELECTRICAL POWER
- Electrical power cord 1500mm long- All units 3 pin 10 amp 1 phase
Electrical box accessed from side withside panel removed
9/12/2014 Page 6
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
Internal Air Flow Requirements
CORRECT AIRFLOWfor both hot and cold units
Vents are not blocked at baseand ensure trays or plates are not blocking airflow at the rear of the unit
INCORRECT AIRFLOWfor both hot and cold units.
Blocked airflow disturbs correctair movement and creates uneven temperatures inside unitEnsure bottom vents are not blocked by plates or productBlocked air flow will retard operationon both HOT and COLD unit
Avoid Radiant and Convective Heat Sources
Heat from other equipment and natural conditions such as direct sunlight on any units can cause cooling to fail andover work the motor
Be aware of potential problems by placing units in adverse ambient conditions.
Locations to be avoided are:
- Close to shop front exterior- In an outside location- In direct sunlight- In a high cross wind area- Near any source producing excessive heat
Increase service intervals for units in dusty or polluted areas
CORRECT AIR FLOW INCORRECT AIR FLOW
CLEAR FLOW AIR FLOW BLOCKED
too much chilled airaround coil can createexcessive ice build up
NO AIR FLOW
BTG AIR FLOW AND UNIT PLACEMENT
9/12/2014 Page 7
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
Rear intake / extract system
BTG Rear Ventilation System
The Cossiga BTG range provides a rearintake and extract ventilation system byusing a unique side mounted compressordesign to provide the ability of the refrigerated units to be placed in more versatilesituations.
Unit front can be fully covered with custom panel joinery to fit any design environment without need for venting to front.
Ambient air intake throughright rear internally ducted through condenser face
Exhaust air extract throughleft rear internally ducted to environment
REAR VENTILATIONBTG GLASS TOWER SERIES
9/12/2014 Page 8
CLIP ON PANEL SYSTEM (COPS) BTG
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
Integrated Clip System Melteca Finish Options
Burnished Wood
Affinity Maple
Bliss Shitake
An easy to install option to eliminate the need for building a nib wall, simply roll in, clip on and start trading !
These clip on / clip off panels are offered in routed 18mm MDF with Melteca finish inthree colour options.
Available in 600 - 900 - 1200 -1500 length optionswith end panels
9/12/2014 Page 9
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
ACCESSORIESBTG GLASS TOWER SERIES
Top Mounted Controller PanelFor against wall installations.
Water Humidity Dish- Heated UnitsPlaced on bottom base tray of BTG unit.Perforated lid is removable.
Base Tray Shelf - Heated UnitsPlaced on bottom base tray of BTG heated unit to raise productoff base.Stainless steel to match upper shelves.Sold in pairs.
Price TabStainless steel price tabs.
Use adhesive label or write withmarker.Sold in packs of 20.
Measures 60mm x 30mm.
Stainless Steel Tong HolderDrop into counter tray race.
Cossiga recommends these units be able to be removed for cleaning.
Stainless Steel Bag HolderDrop into counter tray race.
Cossiga recommends these units be able to be removed for cleaning.
180
mm
220 mm
190 mm
105 mm
75 mm
100 mm190 m
m
80 mm
9/12/2014 Page 10
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
more information in service section
GLASS SHELF SIZES AND QUANTITYModel Glass Thickness Top Shelf mm glass part code
Toughened Depth Length No. Panes
BTG9 6mm 450 780 1 S21-295
BTG12 6mm 450 540 2 S21-296
BTG15 6mm 450 690 2 S21-297
BTG 12 and BTG 15 two panes per shelf level
Stainless steel glass shelfsupport brackets
BTG 9 one pane per shelf level
450
GLASS SHELVES
The glass tower refrigerated and heated series can also be fitted with glass shelves
The wire racks are removed and replaced with the 6mm toughened glass panes by the dealer on site. Stainless steel support brackets are used to hold the glass on the shelf frame
Glass shelves option is classed as an accessory at additional cost
Available only in AUS/NZ. International sales brackets only supplied and glass to be supplied by dealer
GLASS TOWER SERIES GLASS SHELF OPTIONSBTG
9/12/2014 Page 11
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
more information in service section
PIE TRAYSMODEL CODE QUANTITY DIMENSIONS
BTGHT6 BTGPT6 4 per shelf 16 x Tray 120(w) Shelves 445(d)
BTGHT9 BTGPT9 6 per shelf 24 x Tray 130(w) Shelves 445(d)
BTGHT12 BTGPT12 9 per shelf 36 x Tray 120(w) Shelves 445(d)
PIE TRAYS
Placed on shelves in heated unitsto contain rows of pies or heated product.
Adds a stylish quality look and makes similar product easilyidentifiable.
Stainless steel construction.
GLASS TOWER SERIESBTGHT HEATED UNITS ACCESSORIES - PIE TRAYS
9/12/2014 Page 12
Contact us T +649 580 8471 F +649 580 2514 AUS. T 1300 099 215 E [email protected] download C.A.D. blocks please visit www.cossiga.com
GASTRONORM PAN SYSTEM
GASTRONORM PAN SYSTEM
MODEL CODE PANS QUANTITY PER SYSTEM
BTGHT9 F92-316 3 per unit 3 x 265mm x 325mm pans and frame
BTGHT12 F92-317 4 per unit Two of 2 x 265mm x 325mm pans and frame
GASTRONORM PAN SYSTEM
BTGHT GLASS TOWER SERIES - ACCESSORIES
Placed on the base of heated units.Provides an angled display viewof heated product more suitablefor pan storage.
Stainless steel construction.
9/12/2014 Page 13