PRODUCT OVERVIEWGRAPHICS SOLUTIONS
GRAPHICS SOLUTIONS
Graphics Controllers
& Development Tools
PRODUCT OVERVIEWGRAPHICS SOLUTIONS
Copyright © 2008 Fujitsu Limited Tokyo, Japan and Fujitsu Microelectronics EuropeGmbH. All Rights Reserved.
The information contained in this document has been carefully checked and isbelieved to be entirely reliable. However Fujitsu and its subsidiaries assume noresponsibility for inaccuracies.
The information contained in this document does not convey any licence under thecopyrights, patent rights or trademarks claimed and owned by Fujitsu.
Fujitsu Limited and its subsidiaries reserve the right to change products orspecifications without notice.
No part of this publication may be copied or reproduced in any form or by any meansor transferred to any third party without the prior consent of Fujitsu.
This brochure contains references to various Fujitsu Graphics Controller productsunder their original development code names. Fujitsu does not lay any claim to theunique future use of these code names.
Designed and produced in the UK. Printed on environmentally friendly paper.
ARM is a registered trademark of ARM Limited in UK, USA and Taiwan.ARM is a trademark of ARM Limited in Japan and Korea.ARM Powered logo is a registered trademark of ARM Limited in Japan, UK, USA, and Taiwan.ARM Powered logo is a trademark of ARM Limited in Korea.ARM926EJ-S and ETM9 are trademarks of ARM Limited.
01
CONTENTS
Introduction to Graphics Controllers 2
Introduction to Business Unit Graphics Solutions 3
MB86290A ‘Cremson’ 4-5
MB86291A ‘Scarlet’ 6
MB86292 ‘Orchid’ 7
MB87P2020A ‘Jasmine’ 8
MB86293 ‘Coral Q’ 9
MB86294 ‘Coral B’ 10
MB86295 ‘Coral P’ & MB86296 ‘Coral PA’ 11
MB86276 ‘Lime’ 12
MB86277 ‘Mint’ 13
MB86297A ‘Carmine’ 14
MB86R01 ‘Jade’ 15
Product Roadmap 16
Evaluation Boards 17
Graphics Controllers Comparison Tables 18-19
EMEA Distributors 20-21
02
PRODUCT OVERVIEWGRAPHICS SOLUTIONS
MaidenheadRegional Office & Mixed Signal Division
MassyRegional Office
MünichGraphics Competence Center,ASIC Design Centre & Regional office
MilanRegional Office
LangenFujitsu Microelectronics EuropeHeadquarters - ASIC, MCU, RFand Multimedia Design Centres
In October 2006 Fujitsu Microelectronics Europe (FME)
created a new Business Unit with the Graphics Competence
Center, which is totally dedicated to Graphics Solutions.
Already a technology leader in the embedded graphics
market, FME is extending this lead by creating new devices
and providing the extensive technical support expected in this
growing market.
New devices target FME’s existing automotive and multimedia
markets, as well as others, which include medical, industrial,
POS, marine, console-gaming and surveillance. FME also
provides additional functionality with products incorporating
sophisticated peripherals and integrated microprocessors.
The new Competence Center undertakes hardware design in
line with Fujitsu Japan to cover logic design of, and macros for,
graphics controllers; chip architecture, prototyping of new
concepts, etc., and software design to include the development
of drivers (Open-GL, Open-VG, etc.), customisation of APIs,
SoC software and tools. Application engineering support
includes in-house technical/customer seminars, evaluation
boards, etc., with particular attention to monitoring designs,
projects, partner networks and customer contact.
For the future, FME plans to grow its Graphics Business by
developing automotive graphics while expanding into other
challenging areas including hand-held navigation systems.
On-going investment in Fujitsu’s own, in-house 90nm process
technology fully supports these plans.
Around 30 specialists, combining hard- and software design,
applications and marketing skills are based in the Graphics
Competence Center in Munich.
Introducing Business Unit GRAPHICS SOLUTIONS
FME’s Business Unit Graphics Solutions is based in Munich and employs 30specialists, combining hard- and software design, applications engineering andmarketing skills.
Fujitsu’s design centres and sales offices.
03
Introduction to GRAPHICS CONTROLLERS
Fujitsu’s new family of graphics controllers will optimise
solutions for embedded graphics applications such as car
navigation and mobile information terminals. The products
in this family have numerous functions that are state-of-the-art
to graphics controllers today, but have been specially
optimised for the area of embedded systems. This means that,
in addition to many 2D and 3D rendering functions, there is a
flexible layer concept, support for screen resolution of up to
SXGA (1280 x 1024) and further features which are of
particular interest in the area of navigation, such as
alpha-blending and anti-aliasing. All derivatives have a CPU
interface to enable direct connection of embedded CPUs and
MCUs, except the Jade family devices, which have an
embedded ARM CPU core. Fujitsu offers a range of graphics
controllers with different levels of integration for various
applications.
In-car navigation is a key target application for Fujitsu’s graphics controllers.
04
PRODUCT OVERVIEWGRAPHICS SOLUTIONS
MB86290A ‘Cremson’ is a 2D/3D graphics controller,
optimised for applications in car navigation systems and
mobile information processing terminals. Adopting various
sophisticated functions, such as flat or Gouraud shading,
bi-linear texture mapping, and Z-buffering, the device offers a
high-speed, superior-performance 3D graphics functionality.
Moreover, anti-aliasing, concaved polygon rendering and fast
line draw features are also included, allowing smooth and
sophisticated-quality rendering. As a result, ‘Cremson’
performs high-quality rendering operations, with similar
quality to leading-edge PC graphics, but with lower power
consumption. ‘Cremson’ supports a 64-bit-wide external
memory interface. This interface is driven at the same
100MHz frequency as its internal operation, to support the
large-memory bus bandwidth that is needed to perform the
high-performance graphics operations described above. Also,
in order to support various kinds of system configurations, the
device offers a configurable host interface for four types of
CPUs (Fujitsu FR30, Hitachi SH3/4, and NEC V832)
without external glue logic.
To address the especially complex Window configurations of
car navigation systems, ‘Cremson’ offers 4 layers of overlay
planes. These layers are (from top to bottom): C (console) layer,
W (window) layer, M (middle) layer and B (base) layer.
All layers can be rendered in 16-bit/pixel colour (65,536
colours displayed at a time) or rendered in 8-bit indirect colour
mode (256 selected out of 262,144 colours). The colour
palette can be defined separately to the C, B and M layers.
A transparent colour option is used to blend the layers directly.
MB86290A ‘Cremson’
An important feature of MB86290A and all subsequent members of the family is that graphical information canbe displayed on four overlapping, independent layers.
The new Graphics Controllers’ support for 3D graphics makes possible featuressuch as ‘bird-view’ perspectives.
05
Layer conceptFor screen separation in wide-screen displays, the M and B
layers can be split into two separate segments (left and right).
This feature is useful when two different reduced map scales
are displayed side by side. Of course, all these layers and
segments can be scrolled independently. In addition, two
hardware cursors are supported.
An ‘alpha-flag’ per pixel is supported for the C-layer. This
feature is useful for blending the C layer colour with all the
layer contents below, providing a variable transparent colour
effect (‘alpha-blending’). ‘Cremson’ consists of 4 block
modules: host interface block, external memory interface
block, display control block, and 2D/3D rendering block. An
internal 64-bit bus called Pixel bus connects these modules.
Also, the host interface block is connected to each of the other
3 blocks independently to avoid display and/or rendering
operations when the host CPU attempts to access these
modules.
Key features• CMOS 0.25µm technology
• Display resolutions up to 1024 x 768
• 4 layers of overlay display (bottom 2 layers are both split
into separate segments)
• RGB analogue output (high speed DAC)
• Includes various kinds of 2D/3D graphic acceleration
functions
• Built-in alpha blending, anti-aliasing and chroma-keying
• Up to 32MB external graphic memory (SDRAM) 64-bit
wide @ 100MHz
• Configurable CPU-interface for embedded CPUs/MCUs
• Supply voltage 3.3V (I/O), 2.5V (Internal)
• QFP-240 Package
• Temperature range -40 to +85°C
MB86290A uses an internal 64-bit-wide pixel bus to connect the main hardwareblocks: Host interface, memory controller, display controller and rendering engine.
06
PRODUCT OVERVIEWGRAPHICS SOLUTIONS
MB86291A ‘Scarlet’
MB86291A ‘Scarlet’ is an enhanced version of MB86290A
‘Cremson’, which adds 16Mbit embedded SDRAM, video
input functions and a geometry processor. The concept of
display layers, 2D/3D rendering functions and the displays
controller features are taken from ‘Cremson’ MB86290A.
Scarlet is optimised for applications in car navigation systems,
which require video-input features, consumer information
processing systems and arcade game applications.
The device has 16Mbit of embedded SDRAM with high
bandwidth (100MHz). No external SDRAM devices are
required for graphic memory. The external video input can be
used to capture video signals according to the standard RBT-
ITU656 YUV4:2:2 format.
Picture-in-picture functions are supported to display the video
image (the W-layer is dedicated for that purpose). To adjust the
dimensions of the video-input format, a flexible video scaler is
integrated.
A geometry processor, capable of performing numeric
calculations for graphical operations, is included. Supported
functions are Affin-conversions, model-view projections,
3D-clipping operations and others. All drawing functions,
display list-formats and software functions are compatible to
the ‘Cremson’ MB86290A.
An additional RGB digital interface offers flexible display
connections.
Key features• CMOS 0.25µm technology
• Display resolutions up to 1024 x 768
• 4 layers of overlay display (bottom 2 layers are both split into
separate segments)
• Digital video input
• Video scaler
• I2C interface
• Geometry processor
• RGB analogue output (high speed DAC)
• RGB digital output (8-bit x 3)
• Includes various kinds of 2D/3D graphic acceleration
functions
• Built-in alpha blending, anti-aliasing and chroma-keying
• Embedded 16Mbit SDRAM graphic memory
• Configurable CPU-interface for embedded CPUs MCUs
• Supply voltage 3.3V (I/O), 2.5V (Internal)
• QFP-208 Package
• Temperature range -30 to +85°C
MB86291A offers some of the most advanced functionality yet developed for usein automotive navigation and multimedia information terminals.
MB86291A adds 16Mbit embedded SDRAM, video input functions and a geometryprocessor.
07
MB86292 ‘Orchid’ is another version of MB86291A ‘Scarlet’,
which has external video memory connection up to 32MB for
those applications where the 2MB embedded SDRAM of
MB86291A ‘Scarlet’ is not sufficient. All functions of ‘Scarlet’
including video input, scaler and a geometry processor are also
available on ‘Orchid’. The concept of display layers, 2D/3D
rendering functions and the display controller features are
taken from ‘Cremson’ and ‘Scarlet’. ‘Orchid’ is optimised for
applications in car navigation systems that require video input
features, consumer information processing and arcade game
functions. The external memory interface can be connected to
Fujitsu FCRAMTM or SDRAM-type memory devices. The
external video input can be used to capture video signals
according to the standard RBT-ITU656 YUV4:2:2 format.
Picture-in-picture functions are supported to display the video
image (the W-layer is dedicated for that purpose). To adjust the
dimensions of the video input format, a flexible video scaler is
integrated. A geometry processor, capable of performing
numeric calculations for graphical operations, is included.
Supported functions are Affin-conversions, model-view
projections, 3D-clipping operations and others. ‘Orchid’ has
only RGB digital outputs for display connections. All drawing
functions, display list-formats, and software functions are
compatible to the ‘Cremson’ MB86290A and ‘Scarlet’
MB86291A.
MB86292 ‘Orchid’
Key features• CMOS 0.25µm technology
• Display resolutions up to 1024 x 768
• 4 layers of overlay display (bottom 2 layers are both split
into separate segments)
• Digital video input
• Video scaler
• I2C interface
• Geometry processor
• RGB digital output (8-bit x 3)
• Includes various kinds of 2D/3D graphic acceleration
functions
• Built-in alpha blending, anti-aliasing and chroma-keying
• External SDRAM or FCRAMTM interface for up to 32MB
graphic memory
• Configurable CPU-interface for embedded CPUs/MCUs
• Supply voltage 3.3V (I/O), 2.5V (Internal)
• QFP-256 Package
• Temperature range -40 to +85°C
MB86292 offers all the functions of MB86291A but allows SDRAM or FCRAM™memory up to 32MB.
MB86292 is optimised for applications in car navigation systems.
08
PRODUCT OVERVIEWGRAPHICS SOLUTIONS
MB87P2020A ‘Jasmine’ is a member of Fujitsu’s graphics
controllers family for low-cost embedded systems with
performance requirements for compact automotive or
consumer application, user interfaces or control panels where
a high integration of functions is required. No external
memory devices are required for graphic memory because of
the 8Mbit embedded SDRAM.
The MB87P2020A supports almost all LCD panel types
(digital or analogue interface) and CRTs or other progressive
scanned monitors/displays, which can be connected via the
analogue RGB output.
The 2D rendering functions are composed out of standard
primitives such as lines, polylines, rectangles, etc., as well as
some special functions like decompression of RLE-bitmaps
and text display. 4 layers of overlay can be displayed
simultaneously.
A video input interface was developed, which allows
acceptance of more formats (including YUV and RGB) and
which is compatible to a wider range of video decoder chips.
A programmable converter matrix (YUV to RGB) allows
writing of the YUV formats to layers and to convert back to
RGB for scanning.
In addition, a gamma correction table was added to allow
adjustment of the picture characteristics according to the
connected display requirements and the colour look-up table
that can hold up to 512 entries.
‘Jasmine’ is optimised to work as a companion chip for the
Fujitsu 32-bit RISC devices.
Key features• CMOS 0.25µm technology
• Flexible display controller for almost all standard LCD
panels
• 4 layers of overlay display (out of 16 logical layers)
• RGB analogue output (DAC)
• RGB digital output
• Includes 2D graphic acceleration functions
• Gamma correction
• Embedded SDRAM graphic memory 8Mbit (1MByte)
• Digital video input (RGB and YUV formats)
• CPU-interface for embedded 32-/16-bit CPUs/MCUs
• Supply voltage 3.3V (I/O), 2.5V (internal)
• QFP-208 Package
• Temperature range -40 to +85°C
MB87P2020A is fully compatible with the MB87J2120 ‘Lavender’ and uses thesame internal architecture. No external memory devices are required for graphicmemory because of the 8Mbit embedded SDRAM.MB87P2020A is optimised to work as a companion chip for the Fujitsu 32-bit RISC
devices.
MB87P2020A ‘Jasmine’
Note: The two devices MB87P2020A and MB872040 are identical in pinning,functionality and electrical specifications.
09
MB86293 ‘Coral Q’
The ‘Coral’ device family offers an increased internal
operating frequency of 166MHz, a 64-bit memory bus,
support for six independent layers, advanced alpha-blending
features and enhanced video input facilities. The higher
internal frequency of 166MHz (400MHz for display dot
clocks) enables the rendering engine of the devices to achieve
a factor 10 improvement in texture mapping and drawing
image quality compared to the previous graphics controller
devices.
The enhanced bandwidth allows a much greater rate of access
for graphics elements, and delivers improved scanning
functions at higher display resolutions. The ‘Coral Q’ and
‘Coral B’ devices are compatible with host CPU buses
including Fujitsu FR, Hitachi SH3 and SH4 and NEC V83
without external glue logic. All devices are binary compatible
with previous generation graphics controllers, like the
‘Cremson’, ‘Orchid’ and ‘Scarlet’ devices. This helps to
speed-up developments and save costs because existing
software modules (e.g. map renderer) and drivers can be used
without any modifications.
An enhancement to 2D-drawing functions is the integration of
a line depth display facility, which clearly defines the correct
respective level of intersecting map lines. Enhanced hardware
design also provides improvements in pattern line
performance.
The ‘Coral’ devices address up to 64MB of external SDRAM
or FCRAMTM memory @ 133MHz and are capable of
adjusting picture sizes to optimise the available memory space.
All layers can have a colour depth of 8-, 16- or 24-bits/pixel
and can be changed in position, size and priority. The
maximum logical layer size has been increased to 4096 x 4096
pixels.
Key features• CMOS 0.18µm technology
• Display resolutions up to 1280 x 768
• 6 layers of overlay display (Windows)
• Alpha Plane
• Geometry processor
• RGB digital output (8-bit x 3)
• Includes various kinds of 2D/3D graphic acceleration
functions
• Built-in alpha blending, anti-aliasing and chroma-keying
• External SDRAM or FCRAMTM interface @ 133MHz for
up to 64MB graphic memory
• Configurable CPU-interface for embedded CPUs/MCUs
• Supply voltage 3.3V (I/O), 1.8V (Internal)
• QFP-256 package
• Temperature range -40 to +85°C
MB86293 has a 6-layer structure and a geometry processor that perform co-ordinate conversions at 166MHz.
MB86293 family layer structure.
10
PRODUCT OVERVIEWGRAPHICS SOLUTIONS
D[31:0]
A[25:2]
MD[63:0]
MA[14:0]
MB86294 ‘Coral B’
MB86294 offers video input with upscaling, in addition to the new family features.
MB86294 ‘Coral B’ adds video input to the features of
‘Coral Q’ and is available in a BGA package. The video input
is capable of accepting TV tuner, DVD player or camera
signals in PAL or NTSC video formats (ITU656 format).
Video pictures of diverse resolution and frame frequency rate,
in either progressive or interlaced modes, can be grabbed,
scaled and displayed picture-in-picture.
The latest automotive and consumer appliance screens are
increasing resolution to achieve better readability. They
demand improved picture quality to match, for example, DVD
quality. In order to meet these demands, ‘Coral B’ integrates a
new video input up-scaling facility, which allows a full-screen
mode of multimedia pictures at large resolutions to be
displayed. Both up-scaling and down-scaling can be set
independently in horizontal and vertical directions in pixel or
line resolutions.
Using the Alpha-map features of the ‘Coral’ architecture, a
video picture can be blended smoothly together with rendered
graphics. The alpha map can be freely assigned to any of the
six layers and allows the assignment of 8-bits per pixel,
enabling each pixel to be mixed to control transparency to a
very high degree of accuracy. In addition, all layers can be
blended at a fixed ratio of 256 levels.
To enhance bit BLT (Bit Block Transfers) operations, this
feature can now be combined with alpha-mapping. With this
function, any bitmap can be copied from any source location
(CPU- or Video-memory) onto a layer with an independent
alpha-map. Software routines that make use of this function
can greatly improve image quality (for example anti-aliasing
over a moving background).
Key features • CMOS 0.18µm technology
• Display resolutions up to 1280 x 768
• 6 layers of overlay display (Windows)
• Alpha Plane
• Digital Video input
• Video Scaler (up/down scaling)
• I2C interface
• Geometry processor
• RGB digital output (8-bit x 3)
• RGB analogue output
• Includes various kinds of 2D/3D graphic acceleration
functions
• Built-in alpha blending, anti-aliasing and chroma-keying
• External SDRAM or FCRAMTM interface @ 133MHz for
up to 64MB graphic memory
• Configurable CPU-interface for embedded CPUs/MCUs
• Supply voltage 3.3V (I/O), 1.8V (Internal)
• BGA-256 package
• Temperature range -40 to +85°C
11
MB86295 ‘Coral P’ & MB86296 ‘Coral PA’
MB86295 ‘Coral P’ and MB86296 ‘Coral PA’ are enhanced
versions of ‘Coral B’ with a PCI host interface and a new video
input controller. Any CPU with a 32-bit PCI V2.1-compliant
host interface can be directly connected to ‘Coral P/PA’. The
devices include both master and slave functions and an internal
DMA controller for multi-burst transfers of large quantities of
data between all combinations of PCI data space and Coral
internal areas.
Additional functions provided by the host interface are general
purpose I/O pins and a serial interface. The external video input
of MB86295/6 accepts data conforming to the standards RBT-
ITU656, RBT-ITU601, RGB666 and RGB888. This allows
video signals of various sources to be displayed together with
generated graphics. The video input is capable of accepting TV
tuner, DVD player or camera signals in PAL or NTSC video
formats. In addition, rendered graphics from any other display
controller can be used as video input source.
The video stream is read, modified and written to a video buffer
memory completely independent of the display scanning
process. Video pictures of diverse resolution and frame
frequency rate, in either progressive or interlaced modes, are able
to be grabbed, scaled and displayed picture-in-picture. As with
‘Coral B’, ‘Coral P/PA’ integrates a new video input up-scaling
facility, which now allows a full-screen mode of multimedia
pictures at large resolutions to be displayed. Both up-scaling and
down-scaling can be set independently in horizontal and vertical
directions in pixel or line resolutions.
A set of general I/O pins and a serial interface are also included
for simple external resource control.
Key features • CMOS 0.18µm technology
• Display resolutions up to 1280 x 768
• 6 layers of overlay display (Windows)
• Alpha plane
• Digital video input (various formats)
• Video scaler (up/down-scaling)
• I2C interface
• Geometry processor
• RGB digital output (8-bit x 3)
• RGB analogue output
• Includes various kinds of 2D/3D graphic acceleration
functions
MB86295 block diagram.
• Built-in alpha blending, anti-aliasing and chroma-keying
• External SDRAM or FCRAMTM interface @ 133MHz for up
to 64MBytes graphic memory
• PCI 32-bit V2.1 host interface
• GPIO inputs/outputs
• Serial interface
• Supply voltage 3.3V (I/O), 1.8V (Internal)
• BGA-256 package
• Temperature range -40 to +85°C
The new MB86296 ‘Coral PA’ is a redesigned and feature-
expanded version of ‘Coral P’. This chip has the following
additional features:
• Direct RGB666 video input without conversion to YUV422
• Dual display feature (independent contents on two connected
screens)
• Colour-space conversion method selectable as programmable
option
• Brightness, contrast, saturation control for video input
• PCI bandwidth will increase to approximately 70MBytes/s
• New ROM for geometry engine (enhanced functions)
• Pixel-clock delay of display output is programmable
• PCI bus clock can be used as clock input
• Video texture mapping (RGB555 mode)
• Simultaneous up- and down-scaling
• Enhanced pixel clock output
• 100% pin- and function-compatible to ‘Coral P’
12
PRODUCT OVERVIEWGRAPHICS SOLUTIONS
MB86276 ‘Lime’
MB86276 block diagram.
The new graphics controller MB86276 is the perfect choice for 2D-optimisedgraphic systems based on the Coral family.
Mode 1 HST 32-bit D(31:16) RGB out 8/8/8 RGB in 6/6/6
Mode 2 HST 32-bit D(31:16) RGB out 8/8/8 GPIO (4:0) N/A Video In (7.0)
Mode 3 HST 16-bit RGB out 8/8/8 RGB out 6/6/6 GPIO (3) N/A Video In (7.0)
Mode 4 HST 16-bit RGB out 6/6/6 RGB out 6/6/6 N/A RGB in 6/6/6
MB86276 Host IF multiplexing modes
MB86276 ‘Lime’ is a low-end extension to the Fujitsu graphics
controller family for 2D applications. This chip is based on the
‘Coral’ family core functions, and optimised for 2D rendering.
The graphics controller, rendering engine and video input unit
are taken from the successful ‘Coral P/PA’ but the floating
point co-processor and all 3D-functions have been taken out.
Also, the CPU interface is optimised for more CPU
connections and the device has some functions to support
small footprint graphics applications. MB86296 is 100%
binary-compatible to the ‘Cremson’ and ‘Coral’ families.
Key features • CMOS 0.18µm technology
• Display resolutions up to 1280 x 768
• 6 layers of overlay display (Windows)
• Alpha plane
• Digital video input (various formats)
• Video scaler (up/down scaling)
• I2C master/slave interface
• RGB digital output (8-bit x 3)
• Dual-display support (2xRGB666 output)
• Includes various kinds of 2D graphic acceleration functions
• Built-in alpha blending, anti-aliasing and chroma-keying
• External SDRAM or FCRAMTM interface @ 133MHz for
up to 64MBytes graphic memory
• Standard host interface for embedded CPUs/MCUs
(32-bit/16-bit)
• GPIO inputs/outputs
• Serial interface
• Supply voltage 3.3V (I/O), 1.8V (Internal)
• BGA-320 package
• Temperature range -40 to +85°C
13
MB86277 ‘Mint’
2DRendering
Engine
DisplayController
DAC
Digital RGB
HostCPUBus D(0:31)
A(2:25)
MD(0:31/63)
MA(0:14)
HostInterface
ExternalMemory
Controller
Pixe
l Bus Capture Controller
Analogue RGB
YUV
SDRAMor
FCRAM
Serial I/F
MB86277 block diagram.The new graphics controller MB86277 is the perfect choice for low-end 2D graphicsystems and industrial applications.
Built using CMOS 0.18µm technology and available in an
unleaded LQFP-256 package, MB86277 ‘Mint’ is a solid
option for various types of low-end 2D graphic applications in
the industrial sector. MB86277 ‘Mint’ operates internally at
100MHz and has a 32-bit MCU interface and a 64/32-bit
SDRAM memory interface. The video input unit is capable of
accepting TV tuner, DVD player or camera signals in PAL or
NTSC video formats (ITU656 format). Interlaced video
pictures with various resolutions and frame frequency rates
can be grabbed, scaled down and displayed picture-in-picture.
Using the alpha map, the video picture can be blended
smoothly together with rendered graphics. The alpha map can
be freely assigned to any of the six layers and allows the
assignment of 8-bits per pixel, enabling each pixel to be mixed
to control transparency to a much more defined degree. In
addition, all layers can be blended at a fixed ratio of 256 levels.
To enhance Bit BLT (Bit Block Transfers) operations, this
feature can now be combined with alpha-mapping. With this
function, any bitmap can be copied from any source location
(CPU memory or video memory) and can be copied onto a
layer with an independent alpha map. Software routines that
make use of this function can greatly improve image quality
(for example anti-aliasing over a moving background).
Key features • CMOS 0.18µm technology
• Internal and memory clock frequency: 100MHz
(generated by on-chip PLL)
• Base clock for display clock: 400.9MHz (generated by
on-chip PLL)
• Power consumption < 1.0W (estimated)
• Display resolutions typically from 320 x 240 up to
1280 x 768
• 6 layers of overlay display (windows)
• Alpha plane and constant alpha value for each layer
• RGB888 and RGB analogue display output
• Digital video input (ITU656)
• Video input downscaling
• Rendering engine for 2D graphic acceleration functions
• Geometry processor supporting floating point
transformations
• Texture mapping unit (up to 4096 x 4096)
• Bit BLT Unit for transfers up to 4096 x 4096 surfaces
• Alpha Bit BLT and ROP2 functions
• External 64/32-bit SDRAM interface (100MHz) for
graphic memory (up to 64MBytes)
• Parallel host interface (FR, SH3, SH4, V850,
SparcLite etc.)
• Internal and external DMA support
• I2C interface
• Supply voltage 3.3V (I/O), 1.8V (Internal)
• LQFP-256 Package
• Temperature range -40 to +85°C
14
PRODUCT OVERVIEWGRAPHICS SOLUTIONS
MB86297A ‘Carmine’
MB86297A block diagram.
The MB86297A graphics controller is the first device of its kind to be fabricated in90nm technology.
MB86297A ‘Carmine’ is a high-end extension to the Fujitsu
graphics controller family. This chip carries a brand new
graphics core, which delivers 10x more performance than
‘Coral PA’. All relevant blocks inside the chip are redesigned
and optimised for high-end in-car multimedia applications.
‘Carmine’ is 100% compatible to OpenGL ES 1.1. All
transforming and lighting functions can be executed in
hardware.
As a new feature, ‘Carmine’ has two independent display
output units. Both can generate individual display timings
and resolutions. For each display channel, 8 layers and 4
alpha-planes are available. ‘Carmine’ also features two
independent video input channels - each of them can capture
independent YUV and RGB signals.
Key features • CMOS 90nm technology
• Internal and memory frequency: 266MHz
• Display resolutions up to 1280 x 1024
• 2 x 8 layers of overlay display (windows)
• 2 x 4 alpha planes and constant alpha value for each layer
• Dual-digital video input (various formats)
• Video scaler (up/down scaling)
• Brightness, contrast, saturation control
• Dual-display output
• Rendering engine for 2D/3D graphic acceleration
functions
• OpenGL ES 1.1 compatible
• Geometry processor
• External DDR-SDRAM interface @ 266MHz for up to 1
28Mbytes external memory
• PCI66 host interface
• Supply voltage 3.3V (I/O), 1.2V (Internal), 2.5V (Memory)
• BGA-543 package
• Temperature range -40 to +85°C
15
MB86R01 ‘Jade’
Unified DDR2 Memory Controller (320Mbps)
CAN MediaLB
ARM926EJ-S (320MHz)
ICE
IFET
M IF
Local Peripheral Bus (160MHz)
Local Peripheral Bus
Multi-layer AHB Bus
AHB Bridge
AHB Bridge
SRAM AHB BridgeJTAG IF DMAC
RGB Digital
RGB Digital
VIN
VIN
I$ 16kB
D$ 16kB
ADCSPIPWMGPIOUARTI2CI2SIDE66SDUSB
Ext Flash/SRAM Bus IFwith Decrypt
Engine
MB86R01 ‘Jade’
Unified DDR2 Memory Controller (320Mbps)
Coral GDC Core
GeometryEngine
Local Peripheral Bus (160MHz)
AHB Bridge
AHB Bridge
SRAM AHB BridgeJTAG IF DMAC
VIN
MUX
MUX
Local Graphics Bus (160MHz)
Dual VideoInput
Dual DisplayController
2D/3DRendering
Engine
ITCM 16kB
DTCM 16kB
ARM PeripheralsRemap, Pause, IRC
MB86R01 block diagram.The new System-on-Chip graphics controller MB86R01 is a very versatile devicewith a large palette of interfaces, offering a wide scope of potential applicationfields.
MB86R01 ‘Jade’ is a highly-integrated device for embedded
automotive graphics applications. Incorporating an
ARM926EJ-S CPU core, together with an enhanced version
of the successful Coral PA graphic processor and a number of
external interfaces, this 90nm technology device is highly
optimised for various types of applications that require
outstanding CPU performance in combination with
sophisticated 2D/3D graphics features in a compact SoC.
Target applications include on-board and mobile navigation
systems, graphical dashboard systems, HUD (head-up display)
units, rear-seat entertainment systems, Point-of-Sale terminals
and industrial control panels.
Key features • CMOS 90nm technology
• ARM926EJ-S CPU core with 16kB instruction and 16kB
data cache
• CPU core: 16kB ITCM/16kB DTCM, ETM9 and JTAG
ICE interface
• Internal/memory frequency: 320MHz
• Display resolutions typically from 320 x 240 up to
1280 x 768
• 6 layers of overlay display (windows)
• Alpha plane and constant alpha value for each layer
• Dual display output (2 separate display controllers are
integrated supporting RGB8, RGB16 and RGB24)
• Dual digital video input (2 separate video capture units
supporting various formats including YUV, RGB and
ITU656)
• Video scaler (up/down scaling)
• Brightness, contrast, saturation control
• Rendering engine for 2D/3D graphic acceleration
functions
• Geometry processor supporting floating point
transformations
• Texture mapping unit (up to 4096 x 4096)
• Bit BLT unit for transfers up to 4096 x 4096 surfaces
• Alpha Bit BLT and ROP2 functions
• External DDR2-SDRAM interface (320MHz) for graphic
memory (up to 128MBytes)
• Parallel flash/SRAM host interface with decryption engine
• Parallel ATA interface
• SD card interface
• CAN interface
• MediaLB interface
• USB 2.0 (host and function) interface
• I2C interface
• I2S interface
• UART interface
• Program protection support: support for encrypted
program code helps prevent unauthorised changes
or access
• Supply voltage 3.3V (I/O), 1.2V (Internal), 1.8V (Memory)
• BGA-484 Package
• Temperature range -40 to +85°C
16
PRODUCT OVERVIEWGRAPHICS SOLUTIONS
Product ROADMAP
New enhanced graphics controllers for various kinds of digital
audio/video applications, in which multimedia functions will
be integrated together are planned as successive products. In
addition, we plan to integrate a CPU core and various I/O
functions and define a single-chip solution for car navigation
applications. As Fujitsu’s primary graphics controllers product
line, the car navigation family will be extended further.
Roadmap of graphics controller devices.
1st Generation 2nd Generation 3rd Generation 4th Generation
90nm
0.18μm
0.25μm
‘00 ‘01 ‘02 ‘04‘03 ‘05
Under development or samples only
‘08‘07‘06
80MHz,4 layers, 2D
100MHz, 4 layers,2D/3D
166MHz, 6 layers,2D/3D
330MHz, ARM9+ Graphics
266/133MHz, 8 layers,2D/3D, GL ES 1.1
CremsonScarlet
Orchid
Jasmine
Lime
100MHz6 layers, 2D
Indigo
Coral Q Coral B
Coral PCoral PA
Jadetbd
Carminetbd
Navigation Systems
Premium Navigation
Low End Graphics Controller Family
‘10‘09
5th Generation
High-End Infotainment
Cremson Family
Coral Family
Carmine Family
65nm
Cremson, Scarlet, Jasmine Coral Family Carmine, Lime Indigo, Jade tbd
tbd
Jade Family
Sprite Engine Graphics Controller
(0.18μm)
Cluster
Cluster
Mid Navi
Prog. Pixel ShadersGL ES 2.0
MB86297
MB86R01
MB88F332
MB87P2020
Mint
MB86276
MB86277
MB86290MB86291
MB86292
MB86296
MB86295
MB86294MB86293
0.18μm
17
Evaluation BOARDS
MB86297A evaluation board enables designers to build up specific embeddedapplications.
A starterkit is available for the graphics controllers, enabling designers to build upspecific embedded applications with the targeted processor and graphicscontroller together.
For application development support and functional
evaluation, a number of evaluation boards are available from
Fujitsu: PCI adaptor cards with graphics controllers from the
‘Cremson’, ‘Coral’ and ‘Carmine’ families are available, which
enable the evaluation of the device features directly from a
Windows PC. For this, a Windows 2000/XP driver and a map
driver are bundled with this adaptor card in order to get
started, enabling easy programming of the devices from a
Windows-based development environment.
Furthermore, stand-alone modular boards (non-PCI) exist for
the new ‘Lime’, ‘Jade’ and ‘Mint’ controllers. In the case of
‘Lime’ and ‘Mint’ these boards also incorporate Fujitsu’s
MB91F467D microcontroller. The ‘Jade’ Evaluation Board is
actually a four-board modular system offering all the
peripheral interfaces that the SoC itself provides. A separate
bundle also exists for the ‘Jade’ device: the ‘Jade EMWI
System’, which comprises the ‘Jade’ Evaluation Board, plus an
LCD touch panel, EMWI Systems Embedded Wizard
software and a USB dongle (for authorised use of the EMWI
Systems GUI builder ‘EmWi’).
Also, the source code of various application examples is
included. Although the main purpose is software
development, the systems can almost all be used in connection
with an embedded system for evaluation purposes.
MB86290A starterkit seriesThe ‘Cremson’ starterkit is a modular evaluation board, which
provides a stand-alone embedded environment. The kit
hardware consists of two parts, a CPU module, which carries
a Fujitsu 32-bit RISC MCU MB91F36X and a set of
sub-boards for the graphics controllers ‘Cremson’, ‘Scarlet’,
‘Jasmine’ and ‘Lime’. In order to facilitate the appropriate
configuration for the application requirements, the system
allows easy interchange of the CPU type or the graphics
controller.
The interconnection between both module boards is the host-
CPU bus interface. All functions of the graphics devices and
the CPU are present on pin headers, jumpers or switches,
which allow the addition of hardware extensions.
The new CPU Board, equipped with MB91F369, MB901302,
and MB91F467 allows creation and full debugging of
applications under Softune Workbench directly! This CPU-
module has additionally 2MB debugging RAM on board,
which is required for the monitor debugger.
18
PRODUCT OVERVIEWGRAPHICS SOLUTIONS
Graphics Controllers COMPARISON TABLES
Device Name Chip Max Resolution 2D 3D Texture Number Layer Alpha Drawing Alpha Dual Display RGB Digital Frequency (typ. @60Hz) Rendering Rendering Mapping of Layers Blending Blending Output Output
MB87P2020A Jasmine 64MHz 800 x 600 x - - 4 - - - x
MB86290A Cremson 100MHz 1024 x 768 x x up to 4 4-bit flag 4-bit alpha - -512 x 512 blending for drawing
top layer
MB86291A Scarlet 100MHz 1024 x 768 x x up to 4 4-bit flag 4-bit alpha - x512 x 512 blending for drawing
top layer
MB86292 Orchid 100MHz 1024 x 768 x x up to 4 4-bit flag 4-bit alpha - x512 x 512 blending for drawing
top layer
MB86293 Coral Q 166MHz 1024 x 768 x x up to 6 8-bit alpha-plane 8-bit alpha - x4096 X 4096 for 1 layer + 8-bit drawing +
flag blending for Alpha BLTall layers
MB86294 Coral B 166MHz 1024 x 768 x x up to 6 8-bit alpha-plane 8-bit alpha - x4096 X 4096 for 1 layer + 8-bit drawimg +
flag blending for Alpha BLTall layers
MB86295 Coral P 166MHz 1280 x 768 x x up to 6 8-bit alpha-plane 8-bit alpha - x4096 X 4096 for 1 layer + 8-bit drawing +
flag blending for Alpha BLTall layers
MB86296 Coral PA 166MHz 1280 x 768 x x up to 6 8-bit alpha-plane 8-bit alpha x x4096 X 4096 for 1 layer + 8-bit drawing + (same res)
flag blending for Alpha BLTall layers
MB86276 Lime 133MHz 1280 x 768 x - up to 6 8-bit alpha-plane 8-bit alpha x 2x4096 X 4096 for 1 layer + 8-bit drawing + (same res)
flag blending for Alpha BLTall layers
MB86277 Mint 100MHz 1024 x 768 x - up to 6 8-bit alpha-plane 8-bit alpha - x4096 X 4096 for 1 layer + 8-bit drawing +
flag blending for Alpha BLTall layers
MB86297A Carmine 266MHz 1280 x 1024 x x up to 8 x 2 4 x 8-bit alpha-plane 8-bit alpha x 2x4096 X 4096 for 1 layer + 8-bit drawing + (indep res)
flag blending for Alpha BLTall layers
MB86R01 Jade 333MHz up to x x up to 6 x 2 8-bit alpha-plane 8-bit alpha x 2x1024 x 768 4096 X 4096 for 1 layer + 8-bit drawing + (indep res)
flag blending for Alpha BLTall layers
Evaluation Board Description Device
MB86290EB01 PCI board for PCs (Win2000/XP) MB86290A Cremson
MB86291EB01 PCI board for PCs (Win2000/XP) MB86291A Scarlet
MB86292EB01 PCI board for PCs (Win2000/XP) MB86292 Orchid
MB8629XEB01+MB86293EB01* PCI board combination for PCs (Win2000/XP)* MB86293 Coral Q
MB8629XEB01+MB86294EB01* PCI board combination for PCs (Win2000/XP)* MB86293 Coral B
MB86295EB01 PCI board for PCs (Win2000/XP) MB86295 Coral P
MB86296EB01 PCI board for PCs (Win2000/XP) MB86296 Coral PA
MB86297AEB01 PCI board for PCs (Win2000/XP) MB86297A Carmine
CREMSON-STARTERKIT-CRM Subboard for Modular Starterkit MB86290A Cremson
CREMSON-STARTERKIT-ROSE Subboard for Modular Starterkit MB86291A Scarlet
CREMSON-STARTERKIT-JAS Subboard for Modular Starterkit MB87P2020A Jasmine
* Combination of motherboard (MB8629XEB01) and daughterboard (MB86293EB01 or MB86294EB01) – both items have to be ordered separately Order information : Please specify the item according to the ‘Evaluation board’ or ‘Device’ columns.
Comparison table – tools
Comparison table – devices
19
RGB Analogue Video Video Input Video Other Video Geometry CPU Temperature Package ProductOutput Input Formats Scaler I/F Memory Processor Interface Range Status
x x YUV/ - - embedded (1MByte) - FR -40 to +85 QFP-208 MPRGB
x - - - - external (up to 32MByte) - FR,SH3/4, -40 to +85 QFP-240 MPV850
x x YUV down I2C embedded (2MByte) Version 1 FR,SH3/4, -30 to +85 QFP-208 MPscaling V850
- x YUV down I2C external (up to 32MByte) Version 1 FR,SH3/4, -40 to +85 QFP-256 MPscaling V850
- - - - - external (up to 64MByte) Version 2 FR,SH3/4, -40 to +85 QFP-256 MPV850
x x YUV up + down I2C external (up to 64MByte) Version 2 FR,SH3/4, -40 to +85 BGA-256 MPscaling V850
x x YUV/RGB up + down I2C, SIO, GPIO external (up to 64MByte) Version 2 PCI -40 to +85 BGA-256 MP(RGB as scalingconvertedYUV)
- x YUV/RGB up + down I2C, SIO, GPIO external (up to 64MByte) Version 3 PCI -40 to +85 BGA-256 MP(RGB full scalingresolution)
- x YUV/RGB up + down I2C, SIO, GPIO external (up to 64MByte) - 16 or 32-bit -40 to +85 BGA-320 MP(RGB full scaling Host (various)resolution) and serial
x x ITU-R-BT.656 down I2C external SDRAM - FR, SH3/4, -40 to +85 LQFP-256 MPscaling (up to 64MByte) V832,
SPARClite
- 2x YUV/RGB up + down I2C external DDR Version 4 PCI66 -40 to +85 BGA-543 MP(RGB full scaling (up to 128MByte) includingresolution) Lighting
Engine
- 2x 2x ITU-R-BT.656 up + down I2C, IDE66, SD, UART, DDR2-SDRAM Version 3 - -40 to +85 BGA-484 MPscaling MediaLB, CAN, USB2.0, interface (320MHz)
Ethernet, GPIO, JTAG, for graphic memoryI2S, SPI up to 128Mbytes)
Evaluation Board Description Device
CREMSON-STARTERKIT-LIME Subboard for Modular Starterkit MB86276 Lime
CREMSON-STARTERKIT-CPU CPU Module for the ‘Cremson Modular Starterkit’ MB91F362 as host CPU
CREMSON-STARTERKITCPU369 CPU Module for the ‘Cremson Modular Starterkit’ MB91F369 as host CPU + Debug RAM
STARTERKIT MB91302 CPU Module for the ‘Cremson Modular Starterkit’ MB91302 as host CPU + Debug RAM
SK-91F467D-208PFV CPU Module for the ‘Cremson Modular Starterkit’ MB91F467D as host CPU + Debug RAM
SK-86276-91F467D Standalone integrated board MB86276 + MB91F467D as Host CPU
SK-86277-91F467D Standalone integrated board MB86277 + MB91F467D as Host CPU
SK-86R01 Jade Evaluation Board (4 modules) MB86R01
SK-86R01-EMWI Jade Evaluation Board + EMWI software + LCD MB86R01
SK-86R01-TERMINAL Jade Starterkit (2 modules) MB86R01
Comparison table – tools continued
20
PRODUCT OVERVIEWGRAPHICS SOLUTIONS
EMEA DistributorsRutronik Elektronische Bauelemente Beratgerstrasse 36, D-44149 DortmundTel: +49 (0) 2 31/9 50 36-0Fax: +49 (0) 2 31/9 50 36-31
Rutronik Elektronische Bauelemente Mittelstrasse 3, D-01936 Königsbrück (Dresden)Tel: +49 (0)3 57 95/3 96-0Fax: +49 (0)3 57 95/3 96-50
Rutronik Elektronische BauelementeFlughafenstrasse 4, D-99092 ErfurtTel: +49 (0) 3 61/2 28 36 30Fax: +49 (0) 3 61/2 28 36 31
Rutronik Elektronische Bauelemente Heinz-Beusen-Stieg 5D-22926 Ahrensburg (Hamburg)Tel: +49 (0) 41 02/80 39-0Fax: +49 (0) 41 02/80 39-50
Rutronik Elektronische Bauelemente Amselstrasse 33, D-68307 MannheimTel: +49 (0)621/ 76 21 26-0Fax: +49 (0)621/ 76 21 26-17
Rutronik Elektronische Bauelemente Lilly-Reich-Strasse 7, D-31137 HildesheimTel: +49 (0) 51 21/74 18-0Fax: +49 (0) 51 21/74 18-18
Rutronik Elektronische BauelementeLandsberger Strasse 478, D-81241 MünchenTel: +49 (0) 89/88 99 91-0Fax: +49 (0) 89/88 99 91-19
Rutronik Elektronische Bauelemente Südwestpark 10/12, D-90449 NürnbergTel: +49 (0)9 11/6 88 68-0Fax: +49 (0)9 11/6 88 68-90
Rutronik Elektronische Bauelemente Gothaer Strasse 2, D-40880 RatingenTel: +49 (0) 21 02/99 00-0Fax: +49 (0) 21 02/99 00-19
Rutronik Elektronishche Bauelemente Frankfurter Strasse 151c, 63303 DreieichTel: +49 (0) 6103/27003-0Fax: +49 (0) 6103/27003-20
Rutronik Elektronishche BauelementeBasler Landstrasse 8, 79111 FreiburgTel: +49 (0) 761/611 677 22Fax: +49(0) 761/611 677 11
GreeceEBV Elektronik1, Anaxagora Str., GR-17778 Tavros (Athens)Tel: +30 210 34 14 300Fax: +30 210 34 14 304
HungaryEBV ElektronikMontevideo u. 2/B, H-1037 BudapestTel: +36 1 436-72-29Fax: +36 1 436-72-20
Ineltek Hungary Kft.Folyondár utca 30/b, H-1037 BudapestTel: +36 14 53 37 77Fax: +36 14 53 37 78
Rutronik Magyarország KftFehérvári út 89-95, H-1119 BudapestTel: +36 (0)1/371 06 66Fax: +36 (0)1/371 06 67
IrelandEBV ElektronikBallymount Trading EstateBallymount Road, WalkinstownIRL - Dublin 12Tel: +353 (0)1 456 4034Fax: +353 (0)1 456 4035
IsraelEBV ElektronikDrorrim South Commercial Center (Avnet building), P.O. Box 149IL - 40600 Tel MondTel: +972 (0)9 778 02 60Fax: +972 (0)9 796 68 80
ItalyEBV ElektronikViale Palmiro Togliatti 1639, I-00155 RomaTel: +39 06 40 63 665/789Fax: +39 06 40 63 777
Rutronik SA6 Mail de l’EuropeF-78170 La Celle St Cloud, (Paris Ile de France)Tel: +33 (0) 1/30 08 34 40Fax: +33 (0) 1/30 08 34 37
Rutronik SAAllée de la Détente BP16 ZIF-86361 Chasseneuil du Poitou, Cedex (Poitiers)Tel: +33 (0) 5/49 52 88 88Fax: +33 (0) 5/49 52 88 96
Rutronik SA3D rue de ParisImmeuble Atalis 2F-35510 Cesson Sévigné, (Rennes)Tel: +33 (0) 2/23 45 14 40Fax: +33 (0) 2/ 23 45 06 53
GermanyATeG-Ineltek (Headquarters)Hauptstrasse 45, D-89522 HeidenheimTel: +49 (0)7321 93 85 0Fax: +49 (0)7321 93 85 95
ATeG-Ineltek Nord Lindenallee 84, D-22869 SchenefeldTel: +49 (0)4083 96 04 0Fax: +49 (0)4083 96 04 33
ATeG-Ineltek MitteHauptstr. 13, D-63834 SulzbachTel: +49 (0)6028 99 38 0Fax: +49 (0)6028 99 38 38
ATeG-Ineltek SüdAm Fügsee 21, D-82418 MurnauTel: +49 (0)8841 47 77 5Fax: +49 (0)8841 26 60
ATeG-Ineltek GmbH ErfurtGeraerstr. 33, D-99099 Erfurt Tel: +49 (0)361 34 64 28 0Fax: +49 (0)361 34 64 28 1
EBV ElektronikZum Mühlenberg 9, D-07806 Neustadt / OrlaTel: +49 (0)36481 244-0Fax: +49 (0)36481 244-99
EBV ElektronikKitzingstr. 15-19, D-12277 Berlin-MariendorfTel: +49 (0)30 74 70 05-0Fax: +49 (0)30 74 70 05-55
EBV ElektronikIn der Meineworth 21, D-30938 BurgwedelTel: +49 (0)5139 80 87-0Fax: +49 (0)5139 80 87-70
EBV ElektronikAn der Guempgesbruecke 7, D-41564 KaarstTel: +49 (0)2131 96 77-0Fax: +49 (0)2131 96 77-30
EBV ElektronikBorsigstr. 7, D-65205 WiesbadenTel: +49 (0)6122 80 88-0Fax: +49 (0)6122 80 88 99
EBV ElektronikNeue Ramtelstrasse 4, D-71229 LeonbergTel: +49 (0)7152 30 09-0Fax: +49 (0)7152 30 09-0
EBV ElektronikIm Technologiepark 2-8, D-85586 PoingTel: +49 (0)8121 774-0Fax: +49 (0)8121 774-422
Glyn & Co. KGAm Wörtzgarten 8, D-65510 Idstein/Ts.Tel: +49 (0)6126 59 02 22Fax: +49 (0)6126 59 01 11
Glyn & Co.KGRingstrasse 88, D-41334 Nettetal Tel: +49 (0)2157 12 42 25Fax: +49 (0)2157 12 42 11
Rutronik Elektronische BauelementeHead office, Industriestrasse 2, D-75228 IspringenTel: +49 (0) 72 31/801-0Fax: +49 (0) 72 31/82282
Rutronik Elektronische Bauelemente Falkenberg ParkParadiesstrasse 206 bD-12526 BerlinTel: +49 (0) 30/72 32 08-93Fax: +49 (0) 30/72 32 08-95
FranceEBV Elektronik115, Rue Nicolas LedouxImmeuble Hemiris, Bâtiment AF-13854 Aix-en-Provence Tel: +33 (0)4 42 39 65 40Fax: +33 (0)4 42 39 65 50
EBV ElektronikActys Bâtiment 2, Voie 3, BP348F-31313 Labège Cedex (Toulouse)Tel: +33 (0)5 61 00 84 61Fax: +33 (0)5 61 00 84 74
EBV Elektronik29, Avenue des PeupliersF-35510 Cesson Sévigné (Rennes)Tel: +33 (0)2 99 83 00 50Fax: +33 (0)2 99 83 00 60
EBV ElektronikParc Club du Moulin á Vent,33, Av. du Dr. Georges LévyF-69693 Venissieux Cedex (Lyon)Tel: +33 (0)4 72 78 02 78Fax: +33 (0)4 78 00 80 81
EBV Elektronik3, Rue de la RenaissanceF-92184 Antony Cedex (Paris)Tel: +33 (0)1 40 96 30 00Fax: +33 (0)1 40 96 30 30
PN Electronics142-176 avenue de StalingradParc Technologique des Corvettes BP 53F-92703 Colombes CedexTel: +33 (0)1 47 80 67 85Fax: +33 (0)1 47 85 95 12
PN ElectronicsRue Jean Bart, Immeuble CalliopeF-31317 LabegeTel: +33 (0)5 62 88 23 23Fax: +33 (0)5 62 88 23 29
PN Electronics13, impasse des Cerisiers, F-67580 LaubachTel: +33 (0)3 88 90 43 48Fax: +33 (0)3 88 90 37 11
PN Electronics334 Rue des vingt toises-Le Magistere IIF-38950 Saint Martin le VinouxTel: +33 (0)4 38 02 02 03Fax: +33 (0)4 38 02 21 00
Rutronik SAAvenue Gustave Eiffel ZI BP 81F-33605 Pessac, Cedex (Bordeaux)Tel: +33 (0) 5/57 26 40 00Fax: +33 (0) 5/56 07 64 41
Rutronik SA6 Mail de l’EuropeF-78170 La Celle St Cloud, (Gecodis)Tel: +33 (0) 1/30 08 33 26Fax: +33 (0) 1/30 08 33 29
Rutronik SA3 Allée des Centaurées Le Royal IIF-38240 Meylan , (Grenoble)Tel: +33 (0) 4/76 61 00 90Fax: +33 (0) 4/76 61 00 99
Rutronik SA1, Impasse René LebrunF-72000 Le MansTel: +33 (0) 2/43 78 16 97Fax: +33 (0) 2/43 78 19 12
Rutronik SA6. impasse Michel Labrousse BP 1305F-31106 ToulouseTel: +33 (0) 5/61 40 96 50Fax: +33 (0) 5/61 41 75 49
Rutronik SA11, rue du TaninLingolsheim PB 109F-67883 - Tanneries , Cedex (Strasbourg)Tel: +33 (0) 3/88 78 12 12Fax: +33 (0) 3/88 78 02 20
Rutronik SA170, Avenue Jean-Jaurès BP 7113F-69353 Lyon, Cedex 07 (Lyon)Tel: +33 (0) 4/72 76 80 00Fax: +33 (0) 4/72 76 80 05
AustriaATeG-IneltekWagramer Strasse 126/21, A-1220 WienTel: +43 (0)1 204 98 38 0Fax: +43 (0)1 204 90 38
EBV ElektronikDiefenbachgasse 35/1M, A-1150 WienTel: +43 (0)1 891 52-0Fax: +43 (0)1 891 52-30
GLYN ÖsterrichCampus 21 / Businesspark Wien SüdLiebermannstrasse A102 / 301A-2345 Brunn am GebirgeTel: +43 (0)1 86670 214 00 Fax: +43 (0)1 86670 214 05
Rutronik Elektronische BauelementeDurisolstrasse 7, A-4600 WelsTel: +43 (0) 72 42/4 49 01Fax: +43 (0) 72 42/4 49 01 33
Rutronik Elektronische BauelementeWaidhausenstrasse 19, Top 10, A-1140 WienTel: +43 (0) 1/4 19 65 50Fax: +43 (0) 1/4 19 65 50 33
BelgiumEBV ElektronikKouterveldstraat 20, B-1831 DiegemTel: +32 (0)2 716 00 10Fax: +32 (0)2 720 81 52
Rutronik Elektronische BauelementeKeppekouter 1, Ninovesteenweg 1989320 Erembodegem-AalstTel: +32 (0) 53/60 65 90Fax: +32 (0) 57-77 12 62
BulgariaRutronik Elektronische Bauelementeul. Cherkovna No.57, Büro No.16BG-1505 SofiaTel: +359 2 9430330Fax: +359 2 9430331
Czech RepublicEBV ElektronikArgentinska 38 / 286, CZ-170 00 Praha 7Tel: +420 234 091 011Fax: +420 234 091 010
Rutronik Elektronische Bauelemente CZ spol.s.r.o, Rooseveltova 13CZ-160 00 Praha 6Tel: +420 233 343 120Fax: +420 233 323 955
Rutronik Elektronische Bauelemente CZ spol.s.r.o, Slavickova 1a, CZ-63800 BrnoTel: +420 (0) 5/45 19 35 17Fax: +420 (0) 5/45 22 22 56
DenmarkEBV ElektronikRosenkæret 11 C, DK-2860 SøborgTel: +45 (0) 39 69 05 11Fax: +45 (0) 39 69 05 04
EBV ElektronikVed Lunden 9, DK-8230 AabyhøjTel: +45 86 25 04 66Fax: +45 86 25 06 60
Rutronik Elektronische BauelementeHerstedostervej 27-29, 2620 AlbertslundTel: +45 70 20 19 63Fax: +45 70 20 19 73
FinlandEBV ElektronikPihatörmä 1 a, FIN-02240 EspooTel: +358 (0)9 27 05 27 90Fax: +358 (0)9 27 09 54 98
EBV ElektronikNahkatehtaankatu 2, FIN-90100 OuluTel: +358 (0)8 562 49 10Fax: +358 (0)8 562 49 15
Rutronik Elekronische Bauelemente Mannerheimintie 12 B, 5th Floor00100 HelsinkiTel: +358 (0) 9 2516 6300Fax: +358 (0) 9 2516 6157
21
EBV ElektronikCorso Vercelli, 348, I-10156 TorinoTel: +39 011 262 56 90Fax: +39 011 262 56 91
EBV ElektronikVia C. Frova, 34I-20092 Cinisello - Balsamo (MI)Tel: +39 02 66 09 62 90Fax: +39 02 66 01 70 20
EBV Elektronik s.r.l. (Napoli)Quartiere Soccavo, Via Paolo della Valle, 321-80126 NapoliTel: +39 08 17 28 16 58Fax: +39 08 17 67 22 67
EBV ElektronikVia Campagna, 12, I-41010 Cognento (MO)Tel: +39 059 2924 211Fax: +39 059 2929 486
EBV ElektronikVia Panciatichi, 40, Palazzo 11, I-50127 FirenzeTel: +39 055 43 69 307Fax: +39 055 42 65 240
EBV ElektronikZona Industriale, Via IX Strada,23/C int. 2I-35100 PadovaTel: +39 04 97 92 36 17Fax: +39 04 98 07 48 74
Malpassi s.r.l.Via Baravelli 1I-40012 Calderara di Reno BolognaTel: +39 051 72 72 52Fax: +39 051 72 73 78
Melchioni Electronica S.p.A.Divisione Industria, Via Pietro Colletta 37I-20135 MilanoTel: +39 025 79 43 54Fax: +39 025 41 34 001
Rutronik Italia S.r.l.Via Caldera, 21, Centro Direzionale S.SiroI-20153 Milano (MI)Tel: +39 02 40 951 1Fax: +39 02 40 951 224
Rutronik Italia S.r.l.Viale Togliatti, 25, I-40133 Bologna (BO)Tel: +39 051 351 94 00Fax: +39 051 351 94 90
Rutronik Italia S.r.l.Via V. Emanuele, 33, I-50041 Calenzano (FI)Tel: +39 055 88 27 332Fax: +39 055 88 10 364
Rutronik Italia S.r.l.Via Arcora,110 - Palazzo GecosI-80013 Casalnuovo di Napoli (NA)Tel: +39 081 52 28 709Fax: +39 051 31 75 131
Rutronik Italia S.r.l.Via Savelli, 62, I-35129 Padova (PD)Tel: +39 049 86 978 00Fax: +39 049 86 978 90
Rutronik Italia S.r.l.Via Del Maggiolino, 125, I-00155 Roma (RO)Tel: +39 06 228 782 1Fax: +39 06 228 782 689
Rutronik Italia S.r.l.Strada Torino, 43/45 EuropalaceI-10043 Orbassano (TO)Tel: +39 011 90 220 00Fax: +39 011 90 63 913
Rutronik Italia S.r.l150/B, Via Primo Maggio, 60131 Ancona (AN)Tel: +39 071 2916218Fax: +39 071 2916873
LithuaniaRutronik Elektronische BauelementeRaudondvario pl.76, 47182 KaunasTel: +37 (0) 37 261780Fax: +37 (0) 37 261780
NetherlandsEBV ElektronikPlanetenbaan 116. NL-3606 AK MaarssenbroekTel: +31 (0)346 58 30 10Fax: +31 (0)346 58 30 25
Glyn BeneluxWaalreseweg 17 NL-5554 HA Valkenswaard, NiederlandeTel: +32 (0)1 402 04 97 00Fax: +32 (0)1 402 04 97 84
Rutronik Elektronische BauelementeMadame Curiestraat 2, NL-3316 GN DordrechtTel: +31 (0) 78/6 52 13 80Fax: +31 (0) 78/6 52 13 81
NorwayEBV ElektronikRyensvingen 3 B PO Box 101Manglerud, N-0612 OsloTel: +47 22 67 17 80Fax: +47 22 67 17 89
Rutronik Elektronische BauelementePostboks 4814, 0422 Oslo, ManglerudTel: +47 21 52 01 58Fax: +47 21 52 00 10
PolandEBV ElektronikPlac Solny 16, PL-50-062 WroclawTel: +48 (0)71 34 229 44Fax: +48 (0)71 34 229 10
Rutronik Polska Sp. z.o.o.ul. Sasiedzka 11, PL-44244 ZoryTel: +48 32/4 75 90-20Fax: +48 32/ 4 75 90-22
Rutronik Polska Sp. z.o.o.ul. Batorego 28-32, PL-481-366 GdyniaTel: +48 (0) 58 / 783 20 - 20Fax: +48 (0) 58 / 783 20 ? 22
Rutronik Polska Sp.z.o.o.ul. Legnicka 5254204 WroclawTel: +48 (0) 71/350 0800Fax: +48 (0) 71/350 3810
PortugalAnatronic PortugalRua Captião Leitão, No 26-1o Esq2800-132 AlmadaTel: +351 (0) 219 376 267Fax: +351 (0) 219 371 834
Rutronik Elektronische BauelementeAvenida Dr. Carlos BacelarEdificio Saza No 968Escritório No 6-A, 4.760-103 Vila Nova deFamalicãoTel: +351 (0) 252 312 336Fax: +351 (0) 252 312 338
RomaniaRutronik Elektronische BauelementeBucurestiTel: +40 (0) 212 105 782Fax:+40 (0) 314 087 476
Rutronik Elektronische BauelementeMaresal C-tin Prezan 142300695 TimisoaraTel: +40 (0) 25 64 01 242Fax: +40 (0) 25 64 01 242
RussiaATeG-Ineltek RussiaKutusovsky Prospekt 14, Building 1, Office 70RUS-121248 Moscow, RussiaTel. +7 (0) 959 74 81 18Fax. +7 (0) 952 43 08 96
EBV ElektronikVasilkovskaya str. 14UA 03040 Kiev, RussiaTel: +380 44 496 22 26Fax: +380 44 496 22 27
EBV ElektronikKorovinskoye Chaussee 10Build 2, Off. 28, RUS-127486 MoscowTel: +7 (0) 959 37 87 07Fax: +7 (0) 959 37 87 06
Rutronik Beteiligungsgesellschaft mbHHaus 3, Büro 403, Leningradskoje Chausse 16RUS-125171 MoscowTel: +7 (0) 9 51 59 92 55
SlovakiaEBV Elektronik s.r.o.Digital Park, Einsteinova 21, SK-85101 Bratislava Tel: +421 2 321 111 41 Fax: +421 2 321 111 40
Rutronik Elektronische BauelementeLazovná 1197401 Banská BystricaTel: +421 (0) 48 47 223 00Fax: +421 (0) 48 47 223 08
SloveniaEBV ElektronikDunajska cesta 159, SL-1000 LjubljanaTel: +386 (0)1 5609 778Fax: +386 (0)1 56 09 877
Rutronik Elektronische BauelementeBrnciceva 131213 Ljubljana-CrnuceTel: +386 (0) 1 561 14 58Fax: +386 (0) 1 561 20 53
South AfricaEBV ElektronikWoodlands Office Park141 Western Service RoadBuilding 14-2nd FloorZA - 2157 Woodmead, JohannesburgTel: +27 (0) 11 236 19 00Fax: +27 (0) 11 236 19 13
EBV ElektronikFleetway House, 5th Floor MartinHammerschlag WayZA - 8001 Foreshore, Cape Town Tel: +27 (0) 21 421 53 50Fax: +27 (0) 21 419 62 56
EBV Elektronik236 Queen Mary AveZA - Glenmore, Durban 4001Tel: +27 (0)31 205-1205Fax: +27 (0)31 205-2265
SpainAnatronic BarcelonaC/Arquitecto Sert, 7 - 08005 Barcelona (España)Tel: +34 93 22 40 28 3Fax: +34 93 22 40 28 3
Anatronic BilbaoC/Las Mercedes, 25 - 2º Dpto. 2Las Arenas 48930, Vizcaya (España)Tel: +34 94 46 36 06 6Fax: +34 94 46 34 23 5
Anatronic MadridPso. Imperial, 8 - 3ª Plta.28005 Madrid (España)Tel: +34 91 36 60 15 9Fax: +34 91 36 55 09 5
EBV ElektronikAnton Fortuny, 14-16 Esc C 3o 2aE-08950 Esplugues de Llobregat (Barcelona)Tel: +34 93 473 32 00Fax: +34 93 473 63 89
EBV ElektronikC/Ronda de PonienteCentro Empresarial EuronovaE-28760 Tres Cantos/MadridTel: +34 91 804 32 56Fax: +34 91 804 41 03
Rutronik Espana S.LCtra. Canillas 138 - 2a Planta - 9BE-28043 MadridTel: +34 91/300 55 28Fax: +34 91/300 53 28
Rutronik Espana S.LC/ Marqués de Sentmenat 54-5808029 BarcelonaTel: +34 93 444 24 12Fax: +34 93 444 24 87
SagitrónC/ General Almirante, 4Torres Cerdá – Plta. 6 Ofic. AE-08014 BarcelonaTel: +34 9 32 98 85 40Fax: +34 9 32 98 85 45
SagitronC/ Montón de Trigo 2, esq. avda. de la IndustriaE-28760 Tres Cantos , MadridTel: +34 91 8 06 38 00Fax: +34 91 8 06 38 05
SwedenEBV ElektronikSjöängsvägen 7, S-19272 SollentunaTel: +46 (0)8 59 47 02 30Fax: +46 (0)8 59 47 02 31
EBV ElektronikDerbyvägen 20, S-21235 MalmöTel: +46 (0)40 59 21 00Fax: +46 (0)40 59 21 01
Rutronik Nordic ABKista Science Tower, Färögatan 33, 16451 KistaTel: +46 (0) 8 505 54900Fax: +46 (0) 8 505 54950
SwitzerlandAnatec AG Sumpfstrasse 7, CH-6300 ZugTel: +41 (0)4 748 32 32Fax: +41 (0)4 748 32 31
EBV ElektronikAv. des Boveresses 52, CH-1010 LausanneTel: +41 (0)21 654 01 01Fax: +41 (0)21 654 01 00
EBV ElektronikBernstrasse 394, CH-8953 DietikonTel: +41 (0) 44 745 61 61Fax: +41 (0) 44 745 61 00
Rutronik Elektronische Bauelemente AGHölzliwisenstrasse 5, CH-8604 VolketswilTel: +41 (0) 1/947 37 37Fax: +41 (0) 1/947 37 47
TurkeyEBV ElektronikBayar Caddesi, Gülbahar Sok. No:17Perdemsaç Plaza, 13th Floor, D:134Kozyatagi, TR-34742 IstanbulTel: +90 (0)216 463 13 52Fax: +90 (0)216 463 13 55
United KingdomEBV ElektronikThames House, 17 Marlow RoadMaidenhead, Berkshire, SL6 7AATel: +44 (0)1628 770 707Fax: +44 (0)1628 783 811
EBV Elektronik144 West George Street, Glasgow, G2 2HGTel: +44 (0)141 352 20 50Fax: +44 (0)141 352 20 59
EBV ElektronikManchester International OfficeCentre Suite 5B, Styal RoadManchester, M22 5WBTel: +44 (0)161 499 34 34Fax: +44 (0)161 499 34 74
EBV Elektronik12 Interface Business ParkBincknoll Lane, Wootton BassettWiltshire, SN4 8SYTel: +44 (0)1793 849 933Fax: +44 (0)1793 859 555
Rutronik UK LtdDunscar House, Deakins Business ParkBlackburn Road, Egerton, Bolton, BL7 9RPTel: +44 (0) 12 04 60 22 00Fax: +44 (0) 12 04 60 22 10
ATeGwww.anatronic.com
ATeG Ineltek GmbH:www.ineltek.de
EBV Elektronik GmbH:www.ebv.com
Glyn GmbH & Co. KG:www.glyn.de
Farnellwww.farnell.com
Malpassi srl:www.malpassi.com
Melchioni Electronica SpA:www.melchioni.it
PN Electronics:www.pne.fr
Rutronik:www.rutronik.com
Sagitron:www.sagitron.es
Web Sites
ASK FUJITSUContact us on +49(0) 61 03 69 00 or visithttp://emea.fujitsu.com/microelectronics
FME-G01-0208