Components, options and accessories Mounting the equipment/ Adaptation plate Dimensions/Free space Electrical power connection ITEM DESCRIPTION DIMENSIONS A EQUIPMENT LENGTH 587 mm B EQUIPMENT WIDTH 341 mm C EQUIPMENT HEIGHT 481 mm D EQUIPMENT HEIGHT WITH AUTOMATIC FEEDER (APPROX.) 577 mm E EQUIPMENT LENGTH WITH ELECTRICAL CABINET OPEN 838 mm LN ~ 230V 50 Hz + PE 3N ~ 400V/230V 50 Hz + PE EQUIPMENT No. OUTPUT 1 PHASE 3 PHASES 230 VAC 400 VAC Y Micron MOD 2 21.39 A 10.95 A 4 31.82 A 10.95 A 6 42.26 A 15.65 A 2 Ø6-12mm ITEM A 92 mm B -- C 381 mm D 571 mm E 49 mm F 249 mm G 334 mm M8 M8 D E A G F B C B Meler Gluing Solutions, S.A P.I. Los Agustinos, calle G, nave D-43 E - 31160 ORCOYEN Navarra (España) Tel.: + 34 948 351 110 Fax: + 34 948 351 130 e-mail: [email protected]www.meler.eu GLUING SOLUTIONS Fitting straight short Warning light VP system Low level detector Adaptation plate Hose Automatic feeder E A C D 3 L3 N PE L1 L2 L3 N PE LN ~ 230V 50 Hz + PE 3N ~ 400V/230V 50 Hz + PE Pneumatic and hose connection P= 0 bar 1 9/16“ 6 x 1 3 5 2 4 6 3 Ø8mm Ø10mm P max = 6 bar 2 1 3 5 2 4 6 4 Note: Both the air supply intake of the equipment such as air supply to the solenoid valve of the automatic feeder must be different. QUICK START GUIDE: MICRON MOD Warning: Risk of electrical shock. Carelessness may produce injury or death. Warning: Hot zone with high temperatures. Risk of burns. Use thermal protective equipment. Warning: System under pressure. Risk of burns or particle projection. Use thermal protective equipment and googles. Warning: Important information for the correct use of the system. May include one or several of the previous hazards, and therefore must be kept in mind to avoid damage and injury. Warning: The micron MOD melters are equipment with current technology and with certain foreseeable risks. Therefore, only allow qualified personnel with sufficient training and experience to use, install or repair this equipment. In case of doubts in the moment of installation, refer to the corresponding instructions manual. If you want this guide in other language, see the website: http://www.meler.eu/Products/manuals-documentation.aspx M8 M8 1
Transcript
Components, options and accessories
Mounting the equipment/ Adaptation plate
Dimensions/Free space
Electrical power connection
ITEM DESCRIPTION DIMENSIONSA EQUIPMENT LENGTH 587 mm
B EQUIPMENT WIDTH 341 mm
C EQUIPMENT HEIGHT 481 mm
D EQUIPMENT HEIGHT WITH AUTOMATIC FEEDER (APPROX.)
577 mm
E EQUIPMENT LENGTH WITH ELECTRICAL CABINET OPEN 838 mm
Este plano es propiedad exclusiva de MELER APLICADORES DE HOT - MELT S.A. Todos los derechos reservados. This drawing is owned sole of MELER APLICADORES DE HOT- MELT S.A. All rights reserved.
Note: Both the air supply intake of the equipment such as air supply to the solenoid valve of the automatic feeder must be different.
QUICK START GUIDE: MICRON MOD
Warning: Risk of electrical shock. Carelessness may produce injury or death. Warning: Hot zone with high temperatures. Risk of burns. Use thermal protective equipment. Warning: System under pressure. Risk of burns or particle projection. Use thermal protective equipment and googles. Warning: Important information for the correct use of the system. May include one or several of the previous hazards, and therefore must be kept in mind to avoid damage and injury.
Warning: The micron MOD melters are equipment with current technology and with certain foreseeable risks. Therefore, only allow qualified personnel with sufficient training and experience to use, install or repair this equipment.
In case of doubts in the moment of installation, refer to the corresponding instructions manual. If you want this guide in other language, see the website: http://www.meler.eu/Products/manuals-documentation.aspx
M8M81
Control board
External I/O connections (optional)
Automatic feeder pneumatic connection Connecting the suction tube
Placing the suction tube Introduce the suction tube in the adhesive container.
Connecting control detectors Both detectors are wired in the electrical cabinet.
Starting up the melter equipment
Note: To adjust the programmable times using the timer refer to chapter 4 of the corresponding instructions manual.
8
12
11
9
3
10
7
6
4 5
1. Tank indicator LED 2. Hose indicator LED 3. Gun indicator LED 4. Temperature set point 5. Actual temperature 6. ON/OFF switch 7. Standby function 8. Temperature OK LED and active pump 9. Time scheduling 10. Left/right button - channel selection 11. Up/down button - temperature modification
1 6 01 6 0
1 5 01 5 0
1 2 3 4 5 6 7 8
CN 5Control card
1 common and voltage out + 2 input for inhibitor output 1 3 input for inhibitor output 2 4 input for inhibitor output 3 5 input for inhibitor output 4 6 input for inhibitor output 5 7 input for inhibitor output 6 8 without connection
OUTPUT DISABLE
Valores por defecto
LED DISPLAY COMPONENT HEATING COMPONENT STATUS
constantly lit constant low temperature
blinking slowly as need (according to PID parameters) temperature near set point
blinking rapidly programming or display change in set point values
off not heating temperature reached
On/Off
1
2
P pneumatic P hydraulic
Ratio 1:13,6
2
Ø4-8mm
Temp. OK
1. If it does not have a pressure regulator (PR): 2. If it does have a pressure regulator (PR):
2
1
Ø10 mm
Ø10 mmINLET
OUTLET
2 1Ø10 mm Ø10 mm
INLETOUTLET
3 Ø10 mmConnect 2 and 3
2
3
1 Loosen slightly the three fixing screws indicated counterclockwise.
Place the swievel elbow to the desired position.
Tighten the three fixing screws to the position of the elbow clockwise.
LOAD DETECTOR
CLOSED LID DETECTORYellow button: reset equipment Black button: reset acoustic signal
-- - 5 5
-- - 1 0
º C
Selecting the overheating value/ Standby Temperature adjustment
Return to initial parameter
Select the element
Modify temperatureNext display to record the value:
Next display to record the value:
Below of 40ºC, temperature display and heating OFF
Tank’s set point Tª value by default
For more information about the different functions of the control board, refer to the corresponding instructions manual.
