X43High Efficiency Hypoid Speed Reducer0.25 - 0.75HP, 1328 - 1416 in-lbs, 5.4 - 34.8RPM

· All hardened and ground gears for high efficiency and quiet operation · Interchangeability with most global manufacturers

X43Output Speed (RPM)

Ratio Motor Power (HP)

Output Torque (in-lbs)

Service Factor

OHL Nom. Torque (in-lbs)

Reducer Part Number**

Gearmotor Part Number**

34.8 50.40.75 1278 1

1079 1328 RX43-0050-HSB2S-WGX43-0050-HSB2S-WAD3B

0.5 852 1.6 GX43-0050-HSB2S-WAC3B

31.7 55.20.75 1402 0.9

1079 1328 RX43-0055-HSB2S-WGX43-0055-HSB2S-WAD3B

0.5 935 1.4 GX43-0055-HSB2S-WAC3B

29.2 59.90.75 1521 0.9

1079 1328 RX43-0060-HSB2S-WGX43-0060-HSB2S-WAD3B

0.5 1014 1.3 GX43-0060-HSB2S-WAC3B

26.6 65.70.5 1112 1.2

1079 1328 RX43-0066-HSB2S-WGX43-0066-HSB2S-WAC3B

0.25 556 2.4 GX43-0066-HSB2S-WAA3B

24.4 71.80.5 1215 1.1

1079 1328 RX43-0072-HSB2S-WGX43-0072-HSB2S-WAC3B

0.25 608 2.2 GX43-0072-HSB2S-WAA3B

22.0 79.40.5 1345 1

1079 1328 RX43-0079-HSB2S-WGX43-0079-HSB2S-WAC3B

0.25 672 2 GX43-0079-HSB2S-WAA3B

19.0 92.10.33 1029 1.3

1079 1328 RX43-0092-HSB2S-WGX43-0092-HSB2S-WAB3B

0.25 779 1.7 GX43-0092-HSB2S-WAA3B

18.4 95.00.33 1062 1.3

1079 1328 RX43-0095-HSB2S-WGX43-0095-HSB2S-WAB3B

0.25 804 1.7 GX43-0095-HSB2S-WAA3B

13.8 126.60.33 1414 1

1079 1416 RX43-0127-HSB2S-WGX43-0127-HSB2S-WAB3B

0.25 1071 1.3 GX43-0127-HSB2S-WAA3B

13.1 133.20.33 1488 1

1079 1416 RX43-0133-HSB2S-WGX43-0133-HSB2S-WAB3B

0.25 1127 1.3 GX43-0133-HSB2S-WAA3B

11.7 150.20.33 1678 0.8

1079 1416 RX43-0150-HSB2S-WGX43-0150-HSB2S-WAB3B

0.25 1271 1.1 GX43-0150-HSB2S-WAA3B

9.9 177.3 0.25 1501 0.9 1079 1416 RX43-0177-HSB2S-W GX43-0177-HSB2S-WAA3B

8.3 210.4 0.25* 1781 0.8 1079 1416 RX43-0210-HSB2S-W GX43-0210-HSB2S-WAA3B

7.6 230.8 0.25* 1953 0.7 1079 1416 RX43-0231-HSB2S-W GX43-0231-HSB2S-WAA3B

6.4 272.5 0.25* 2306 0.6 1079 1416 RX43-0272-HSB2S-W GX43-0272-HSB2S-WAA3B

5.4 323.4 0.25* 2737 0.5 1079 1416 RX43-0323-HSB2S-W GX43-0323-HSB2S-WAA3B

Notes: All units shown are standard configuration. Input motor, output shaft and mounting options are available. *Power greater than that which can be supported by the gearbox for continuous duty.

Motor Specification: 230/460 VAC 60/50Hz, 3PH 1800 RPM Nom. - inverter duty *NEMA Input Sizes: W = 56CX = 143/5TCY = 182/4TC Motors 1HP and greater meet EISA efficiency requirements.

TECHNICAL DATA

DRAWINGSBasic Gearbox

Output FlangeMounting

Torque Arm

Output Flange Output Flange

Output Shaft Insert

3.93

7

1.476

ø0.3

74

ø0.3741.969

3.9372.953

1.96

91.240 4.331

ø4.3

31

3.406 6.299

0.1180.394 0.354

5.118

- 0.0

014

- 0.0

028

0.1380.433

1.240 4.331

0.4333.406 7.874

ø5.1

18

6.496

- 0.0

017

- 0.0

033

0.157

0.512

1.240 4.331

0.4333.406 9.843

ø7.0

87- 0

.001

7- 0

.003

3

8.465

0

- 0.0

013

4.331

ø1.0

00

5/16-18

6.618

2.130x 0.83

0.250

1.11

0

2.287

F2SB

TA R/L

F4F3

5.94

5

Mounting holesposition

2.7564.331

ø3.1

50

3.9374 holes M8x0.472

2.03

9

1.988 0.118

2.75

6

StandardHollow shaft

+0.0008 0

- 0.0

012

- 0.0

024

øFA

D

C

B

Hollow Shaft B C D

Imperial 1.000” 1.118” 0.250”

Metric (mm) 25 28.3 8

X43 Nema Flanges øF A

56C 6.5” 8.787”

IEC Flanges øF (mm) A (mm)

63 B5 138 205

71 B5 160 202.5

56 B14 80 202.5

63 B14 90 205

71 B14 105 202.5

ø0.4

33

4.6460.787

4.25

2

1.96

9

1.18

1

5.827

X43

17.5pounds

Gearbox Weight