Get the future. Today.

May - June 2013

4Tax TimeRace in

Multiple Protection Circuit

Air vents for cooling between

cells

Heat sensor

4Hitachi's brushless motors provide higher capacity specifications compared to conventional brushed motors due to no loss of power from friction & sparking

4

When combined with 4.0Ah batteries, brushless motors significantly increase runtime efficiency.

Hitachi 18V slide platform is fully compatible with 4.0Ah and 2.0Ah Hitachi Li-ion batteries.

4Ultra high capacity 4.0Ah batteries provide 33% longer run time over 3.0Ah batteries increasing productivity and less down time. Same size as 3.0Ah batteries but greater capacity.

In carbon brushed motors, carbon brushes contact the motor to complete the circuit and power the tool. Brushes wear and occasionally need maintenance for replacement. The mechanical contact of the brushes on the motor cause electrical loss and frictional resistance, as well as heat build-up and contact wear - all of which rob the motor of performance and decrease durability. A mechanical contact switch must be used to control the increased and decreased flow of electricity to the motor, which causes further electrical loss and wear.

In brushless motors a micro-processor controls the current flow through the motor. This means there are no carbon brushes which reduces maintenance and unexpected downtime. Due to lack of mechanical contact on the motor, minimal heat and motor wear occur. This results in vastly improved electrical efficiency and power transfer. An optical switch is used to communicate with the micro-processor, providing a more responsive variable speed actuation and wear-resistant switch assembly.

Traditional Motors Brushless Motors

Increased Power & Performance

4Tax TimeRace in

WR18DBDLImpact Wrench

UB18DALTorch

WR18DSHLHigh Torque Impact Wrench

WR18DSDLImpact Wrench

DS18DSFLDriver Drill

DS18DSLDriver Drill

DS18DSDLDriver Drill

DS18DBLDriver Drill

WH18DSDLImpact Driver

WH18DBDLImpact Driver

WM18DBLElectronic Pulse Driver

WH18DDLWater & Dust Proof Impact Driver

DV18DSFLImpact Driver Drill

DV18DSLImpact Driver Drill

DV18DSDLImpact Driver Drill

DV18DBLImpact Driver Drill

UB18DSLLantern

CG18DSDLGrass trimmer

UC18YRSL 18V Cooling Charger

CH18DSLHedge trimmer

RB18DSLBlower & Vacuum

R18DSLWet & DryVacuum

UR18DSLRadio

CJ18DSLJig Saw

C18DSLCircular Saw

CR18DSLReciprocatingSaw

G18DSL125mm Angle Grinder

WF18DSLAutomaticScrew Driver

DH18DSLRotary Hammer

THE HITACHI 18V SLIDE NAKED RANGE

ONE SYSTEM.

ONE SOLUTION.

BSL1840 4.0Ah Li-ion BatteryBSL1820 2.0Ah Li-ion Battery

Get the future. Today.

18V Slide Li-ion Range

Also available: ‘Naked’ C18DSL(H4) Also available: ‘Naked’ CJ18DSL(H4)

18V Slide Rotary Hammer Drill DH18DSL

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

• SDS plus chuck with 16mm max drilling capacity• Two mode action: hammer drilling / drilling

Also available: ‘Naked’ DH18DSL(H4)

Also available: 'Naked' DS18DSFL(H4)

Also available: 'Naked' DV18DSFL(H4)

AM/FM Radio UR18DSL(H4)

• Compatible with all Hitachi 9.6V - 18V slide & cassette batteries (excluding 10.8V)• Compatible with MP3 and CD players

18V Slide Impact Driver WH18DSDL(HB)

Includes 2 x 2.0Ah Li-ion batteries with MPC, charger and carry case

• 170Nm tightening torque • Two power mode: save mode for small bits or power mode for larger bits

Also available: ‘Naked’ WH18DSDL(H4)

Now with

2.0Ah

batteries!

Now with

2.0Ah

batteries!

Now with

2.0Ah

batteries!

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

Batteries & charger sold separately• Compatible with all 18v Slide Hitachi cordless products• 4.0Ah BSL1840 - Lightweight at 655g• 2.0Ah BSL1820 - Lightweight at 390g

Includes AC adaptor, batteries & charger sold separately

18V Slide Reciprocating Saw CR18DSL

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

18V Slide 125mm Angle Grinder G18DSL

18V Slide Circular Saw C18DSL 18V Slide Jig Saw CJ18DSL

• Blade can be loaded in upward or downward direction • Tool-less blade change

• 165mm blade with cutting capacity up to 57mm • Electric brake and magnesium blade cover

• Lightweight at 1.8Kg • Safety overload circuit and anti-start safety override when replacing batteries

• Three mode orbital action or straight cut• Tool-less blade change

18V Slide Driver Drill DS18DSFL

18V Slide Impact (Hammer) Driver Drill DV18DSFL

Includes 2 x 2.0Ah Li-ion batteries with MPC, charger and carry case

Includes 2 x 2.0Ah Li-ion batteries with MPC, charger and carry case

• 13mm keyless chuck• 2 speed gearbox with all metal gears

• 13mm keyless chuck• 2 speed gearbox with all metal gears

Also available: ‘Naked’ CR18DSL(H4)

Also available: ‘Naked’ G18DSL(H5)

18V Slide Wet & Dry Vacuum R18DSL(H4)18V Slide Li-ion batteries BSL1840/BSL1820

• Capable of approx. 40mins continuous run time when using 4.0Ah battery • Semi transparent dust case

Batteries & charger sold separately

18V Slide Blower & Vacuum RB18DSL(H4)

• Capable of approx. 27mins continuous run time when using 4.0Ah battery• Can be converted to vacuum with optional accessory: dustbag 323587

* Only available 'Naked' * Only available 'Naked'

* Only available 'Naked'

4Tax TimeRace in

Also available: ‘Naked’ DS18DBL(H4)

Also available: ‘Naked’ WH18DSDL(H4)

Also available: ‘Naked’ WR18DSDL(H4)

Also available: 'Naked' DS18DSL(H4) Also available: 'Naked' DS18DSDL(H4)

Also available: 'Naked' DV18DSL(H4) Also available: 'Naked' DV18DSDL(H4)

Also available: ‘Naked’ WM18DBL(H4)

18V Slide Electronic Pulse Driver WM18DBL

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

• 30% more efficient Hitachi brushless motor• 5 operation modes - easily select the right function for the right job

18V Slide Impact Wrench WR18DBDL

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

• 250Nm tightening torque • 30% more efficient Hitachi brushless motor

18V Slide Impact (Hammer) Driver Drill DV18DBL

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

18V Slide Driver Drill DS18DBL

• 30% more efficient Hitachi brushless motor• 4 stage speed selector and electronic switch - 50% less trigger force required

18V Slide Driver Drill DS18DSL

18V Slide Impact (Hammer) Driver Drill DV18DSL 18V Slide Impact (Hammer) Driver Drill DV18DSDL

18V Slide Driver Drill DS18DSDL

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

• 13mm single sleeve metal keyless chuck with automatic spindle lock• 2 speed gearbox with all metal gears

• 13mm single sleeve metal keyless chuck with automatic spindle lock• 2 speed gearbox with all metal gears

• 13mm single sleeve metal keyless chuck with automatic spindle lock• 2 speed gearbox with all metal gears

• 13mm single sleeve metal keyless chuck with automatic spindle lock• 2 speed gearbox with all metal gears

18V Slide Impact Driver WH18DBDL

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

18V Slide Impact Driver WH18DSDL

18V Slide Impact Wrench WR18DSDL

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

18V Slide High Torque Impact Wrench WR18DSHL

• 170Nm tightening torque • Two power mode: save mode for small bits or power mode for larger bits

• 255Nm tightening torque • Two power mode: save mode for small bits or power mode for larger bits

• 30% more efficient Hitachi brushless motor• 4 stage speed selector and electronic switch - 50% less trigger force required

• 165Nm tightening torque • 30% more efficient Hitachi brushless motor

Also available: ‘Naked’ DV18DBL(H4)

Also available: ‘Naked’ WR18DBDL(H4)

Also available: ‘Naked’ WH18DBDL(H4)

Includes 2 x 4.0Ah Li-ion batteries with MPC, cooling charger and carry case

• 480Nm tightening torque • Forward & reverse rocker switch

Also available: ‘Naked’ WR18DSHL(H4)

Get the future. Today.

Hitachi Li-ion batteries have a multiple protection circuit fitted that monitors every cell in the battery.

This protects the battery and tool by providing overload protection which stops the tool instantly in the event of a jam or overload. It gives over charge and over discharge protection which ensures the battery life is extended.

Multiple Protection Circuit

Air vents for cooling between

cells

Heat sensor

MPC18V Li-ion Combination Pack KC18DJL

2 piece brushless pack includes: • DV18DBL Impact (hammer) driver drill• WH18DBDL Impact driver• 2 x 4.0Ah Li-ion slide batteries with MPC• UC18YRSL Cooling charger • Carry case

18V Li-ion Combination Pack KC18DOL

2 piece brushless pack includes:• DV18DBL Impact (hammer) driver drill• WR18DBDL Impact wrench• 2 x 4.0Ah Li-ion slide batteries with MPC• UC18YRSL Cooling charger • Carry case

18V Li-ion Combination Pack KC18DKL(HA)

2 piece pack includes:• DV18DSDL Impact (hammer) driver drill• WH18DSAL Impact driver• 2 x 4.0Ah Li-ion slide batteries with MPC• UC18YRSL Cooling charger • Carry case

18V Slide Li-ion Range

4Tax TimeRace in

Improved technology has enabled a significant upgrade of Hitachi power tool ergonomics.

Improved ergonomics allows for better communication between the user and the tool, improved user comfort, reduced fatigue and most importantly reduced injury risk.

Comfort18V Li-ion Combination Pack KC18DGRL

3 Piece Pack Includes:• DV18DSDL Impact (hammer) driver drill• WR18DSDL Impact wrench• G18DSL 125mm Angle grinder• 2 x 4.0Ah Li-ion slide batteries with MPC• UC18YRSL Cooling charger • Carry case

18V Li-ion Combination Pack KC18DGDL

3 Piece Pack Includes:• DV18DSDL Impact (hammer) driver drill• WH18DSDL Impact driver• G18DSL 125mm Angle grinder• 2 x 4.0Ah Li-ion slide batteries with MPC• UC18YRSL Cooling charger• Carry bag

18V Li-ion Combination Pack KC18DSVL

2 Piece pack includes:• DV18DSFL impact (hammer) driver drill• WH18DSDL impact driver• 2 x 2.0Ah Li-ion slide batteries with MPC• UC18YGSL charger• Carry case

Featuring:• Powerful at 1200W• Suitable for wet & dry operations • Auto power function means tool power connection can be placed straight into the vacuum unit allowing the power to turn on and off when the tool is in use• Stainless steel casing for increasing durability

RP30Y24L Wet & Dry Vacuum

Minimise dust in the workplace with this smart dust extraction solution!

Cutting

Width

82mm!Cutting

Width

82mm!

Get the future. Today.

AC Range

13mm Impact Drill DV13VSS

6.5mm High Speed Drill D6SH 13mm Drill With Safety Clutch D13VB3

82mm Planer P20SF

• 620W motor• Lightweight and compact at 2.5Kg• Max cutting depth 2.6mm• Heavy duty aluminium housing• Blade protection stand and cable holder

20mm Impact Drill DV20VB2(H8)

• 730W motor • 2 speed gearbox • 13mm keyed chuck

• 550W motor• 13mm keyless chuck• Reversible with variable speed• Durable cylindrical housing for increased tool life

• 240W motor • 6.5mm keyed chuck• Single speed fast drilling

• 790W motor• 2 speed gearbox• 13mm keyless chuck

Also available: 16mm Impact Drill DV16VSS

Also available: 20mm Impact Drill with Safety Clutch DV20VB2-SC(H9)

Also available: 18mm Impact Drill DV18V

16mm Impact Drill DV16V

• 590W motor• 13mm keyless chuck• Variable speed with reverse • Durable cylindrical housing and aluminium die-casting inner cover and gear cover

82mm Planer P20ST

38mm High Torque Drill D13VG

• 580W motor• Lightweight and compact at 2.5Kg• Max cutting depth 1.5mm

• 710W motor• 13mm keyed chuck • 0-600 (min-1) variable speed

4Tax TimeRace in

65mm D Handle Jig Saw FCJ65V3

• 400W motor• Variable speed• Compact & lightweight• Can be connected directly to dust extraction unit

185mm Circular Saw C7SB2-K

• 1710W motor • Lightweight at 4.6Kg• Aluminium base• 60mm depth of cut

Includes 2 x blades and carry case

235mm Circular Saw C9SA2

• 2000W motor • Lightweight at 6.8Kg• Aluminium base • 86mm depth of cut

305mm Slide Compound Saw with Laser C12RSH

• 1520W motor• 107 X 312mm cutting capacity • Zero clearance slide structure

• 1450W motor• 88 X 312mm cutting capacity• V-belt drive

• 1010W motor• Lightweight at 3.2Kg• Die-cast aluminium base with PTFE coating• 57mm depth of cut

• 705W motor• 4 mode orbital action• Tool-less blade change

216mm Slide Compound Saw C8FSE

• 1050W motor • 75 X 262mm cutting capacity • Positive mitre stops

255mm Compound Mitre Saw C10FCE2

• 1520W motor • 89 X 101mm cutting capacity • Positive mitre stops

190mm Circular Saw C7MFA

Includes 2 x 40 tooth blades

• 1010W motor • Lightweight at 3.6Kg• Aluminium base • Takes both 185mm & 190mm blades• 68mm depth of cut

110mm Barrel Jig saw CJ110MVA

• 720W motor, variable speed at 2.2Kg• 4 mode orbital action or straight cut • Tool-less blade change by lever

Also available: 305mm Slide Compound Saw with Laser Marker and Digital Readout C12LSH

Also available: 110mm D-Handle Jig Saw CJ110MV

Also available: 216mm Slide Compound Saw with Laser Marker C8FSHE

Also available: 262mm Slide Compound Saw with Laser Marker C10FSH

Also available: 255mm Compound Mitre Saw with Laser Marker C10FCH2

Also available: 235mm Circular Saw with Electronic Brake and PTFE base C9BA2

130mm Reciprocating Saw CR13V

• 1010W motor• Tool-less blade change• Lightweight at 3.3Kg• Variable speed• Dust and water resistant with triple sealing construction

262mm Slide Compound Saw C10FSB

165mm Circular Saw C6SS

90mm D Handle Jig Saw CJ90VST

Get the future. Today.Get the future. Today.

Featuring:

• Paddle (deadman) switch

• Constant speed

• Anti-kickback

• Overload protection

• Soft start

• Restart protection

• Anti-vibration side handle

• 1430W motor

• Lightweight at 2Kg

G13YC2Angle Grinder

Suitable for mining, petroleum and heavy engineering industries

• 950W motor• SDS max chuck with 9 joules impact energy• 38mm max drilling & 105mm core drilling capacity

38mm 2 Mode Rotary Hammer DH38MS

16.5KG Demolition Hammer H65SB2

Includes 1 x chisel, 1 x point and case

• 1400W motor • 42 joules impact energy• 30mm hex drive

40mm 2 Mode Rotary Hammer DH40MRY

• 950W motor• SDS max chuck with 10.5 joules impact energy• 40mm max drilling & 105mm core drilling capacity

5.1KG Demolition Hammer H41MB

• 930W motor• SDS max bits with 10 joules impact energy• Compact and lightweight at only 5.1Kg• 12 stage chisel angle adjustment

24mm 3 Mode Rotary Hammer DH24PC3

• 800W motor • SDS plus chuck with 3.2 joules impact energy• 24mm max drilling & 50mm core drilling capacity

• 620W motor• SDS plus chuck with 1.4 joules impact energy• 22mm max drilling capacity

22mm 2 Mode Rotary Hammer DH22PG

28mm 3 Mode Rotary Hammer DH28PC

• 720W motor• SDS plus chuck with 3.5 joules impact energy• 28mm max drilling & 80mm core drilling capacity

30mm 3 Mode Rotary Hammer DH30PC2

• 850W motor• SDS plus chuck with 5.4 joules impact energy• 30mm max drilling & 90mm core drilling capacity

AC Range

4Tax TimeRace in

125mm Angle Grinder With Paddle switch G13YC2

• 1430W motor• Soft start, constant speed control, overload protection, kick back protection, 0 voltage restart• Shaft lock button for easy wheel change • Tool-less wheel guard

230mm Angle Grinder G23SE2

• 2400W motor• Shaft lock button for easy wheel change• Deadman switch• Three position anti-vibration handle

180mm Angle Grinder G18UBY

• 2400W motor • Soft start• Vibration absorbing main and side handle• Deadman switch

125mm Angle Grinder Cutting Pack G13SR3-BP 125mm Angle Grinder G13SE2

Pack includes:• 730W Angle grinder• 3 x Inox discs • 1 x Grinding wheel• 1 x Diamond wheel• 1 x Tape measure• Carry case

• 1200W motor• Paddle (deadman) switch• Two position anti-vibration handle• Lightweight at 1.9Kg

355mm Cut Off Machine CC14SF

• 2400W motor• Quick change vice• Sturdy aluminium housing• Spark diversion guard• External access to carbon brushes

• 760W motor • Lockable slide switch• Powerful motor with variable grinding speed of 7000 - 29000 (min-1)• Features constant speed control, soft start speed control & variable speed for improved control & safety• Lightweight at 1.8Kg

125mm Angle Grinder G13SB3

• 1300W motor• Lockable slide switch• Shaft lock button for easy wheel change• Two position anti vibration side handle• Tool-less wheel guard

100mm Angle Grinder With Paddle Switch G10SQ

• 840W motor• 196mm ultra slim grip circumference• Paddle (deadman) switch

Also available: 125mm Angle Grinder with Paddle Switch G13SQ

Also available: 100mm Angle Grinder Cutting Pack G10SR3-BP

180mm Angle Grinder G18SE3

• 2400W motor• Anti vibration side handle• Tool-less wheel guard • Deadman switch

Die Grinder GP2S2 Die Grinder GP3V

230mm Angle Grinder G23UB2

• 520W motor • Lockable slide switch• Powerful motor with high grinding speed of 29000 (min-1)• Compact design for easy access to hard to reach places• Lightweight at 1.7Kg

• 2400W motor• Soft start• Three position anti- vibration handle• Tool-less guard

Get the future. Today.

The Hitachi PureFire™ two stroke engine is all innovation achieving:

• Up to 30% less fuel consumption • 70% lower emissions • Up to 30% less weight than four stroke engines

This engine also features outstanding throttle response and provides more usable power and torque.

Hitachi’s S-Start feature reduces the amount of pull force required to start the engine by up to 50%

• 0.89kW 23.9cc PureFire™ engine• 275km/h air velocity• 12.5m³/min air volume• Compact & lightweight at 3.9Kg

Handheld Blower RB24EA

Backpack Blower RB65EF

• 2.9kW 64.7cc PureFire™ engine• 313km/h air velocity & 15.5m³/min air volume• Adjustable shoulder straps• Lightweight at 9.9Kg

350mm (14”) Chain Saw CS33EB

• 1.3kW 32.2cc PureFire™ engine• Auto return choke• Lightweight at 3.8Kg

• 1.3kW 32.2cc PureFire™ engine • Auto return choke • Lightweight at 3.4Kg

300mm (12”) Top Handle Chain Saw CS33EDT

450mm (18”) Chain Saw CS40EA

• 1.8kW 39.6cc PureFire™ engine• Auto return choke• Lightweight at 4.4Kg

500mm (20”) Chain Saw CS51EA

• 2.1kW 50.1cc PureFire™ engine• Auto return choke• Decompression valve

Outdoor Power Equipment

Also available: Straight Shaft Brush Cutter with Bike Handle CG27EAS(HB)

Solid SteelDrive Shaft

Heavy DutyClutch

Heavy DutyReduction Gearbox

4Tax TimeRace in

Hitachi’s Quick Twist multi position rear hedge trimmer handle turns 180 degrees to ensure a safe & comfortable operating position when trimming on different angles

All Hitachi petrol powered grass trimmers & brush cutters are fitted with heavy duty centrifugal clutches providing safety & easy starting

All Hitachi straight shaft grass trimmers & brush cutters are equipped with solid steel drive shafts & reduction gear boxes for durability & increased performance

Power & Performance

Straight Shaft Brush Cutter CG27EAS

• 0.9kW 26.9cc PureFire™ engine• Solid steel drive shaft• Lightweight at 4.9Kg

Hedge Trimmer CH66EB3

• 0.74kW 21.1cc engine• 650mm dual action blades• Lightweight at 5.1Kg

Bent Shaft Grass Trimmer CG22EAB

• 0.63kW 21.1cc PureFire™ engine• S-Start• Lightweight at 3.8Kg

Hedge Trimmer CH50EA3

• 0.74kW 21.1cc engine• 500mm dual action blades• Lightweight at 4.3Kg

Attachment Capable Grass Trimmer CG22EAD

• 0.63kW 21.1cc PureFire™ engine• Solid steel drive shaft• Tool free attachment capable shaft

Get the future. Today.

Earth Auger DA200E13mm Drill DW25EF

Water Transfer Pump A25EB

Hitachi’s full crank engine provides smooth, well balanced performance and power with lower vibrations

• Low resistance• Good performance

• Sharper cutting area• High performance• Low vibrations

• Low noise• Less air resistance • Reduced engine drag • Reduced vibrations

GenuineNylon

Trimming Line

Round

Square

Helicoidal

Chain Saw Accessories Earth Auger Accessories

Nylon Trimming Line Lubricants

• Round, square & helicoidal profiles available• Diameters range from 2.0mm up to 3.3mm• Premium quality European manufactured

• High quality storage bag, chain bars & chains• Universal fit for use on a variety of chainsaws

• Premium quality two stroke & chain bar oils • Available in various volumes• European manufactured

• Fit most 25.4mm earth auger drive shafts• Diameters range from 80mm up to 200mm• Replacement cutters & pilots also available

• 1.15kW 32.2cc engine• Accepts up to 200mm earth auger bits• Single person operation• Earth auger bit not included

• 0.88kW 26.9cc engine• Metal keyless chuck• Forward & reverse rotation

• 0.74kW 21.1cc engine• 120 l/min water flow• 40m head height

Outdoor Power Equipment

4Tax TimeRace in

Pneumatics

16 Gauge C Series Finish Nails15 Gauge DA Series Finish Nails34° Framing Nails

Coil Nailer NV65AF3

Framing Nailer NR90AD

DA Series Finish Nailer NT65MA4C Series Finish Nailer NT65M2

C1 Series Brad Nailer NT32AE2

C1 Series Brad Nailer NT50AE2

Narrow Crown Stapler N3804AB3

• Fires 50 – 90mm 34° framing nails• Sequential & bump fire trigger• Tool-less depth adjustment• Industrial strength top housing

• Fires 16 – 32mm C1 series brad nails• Sequential & bump fire trigger• Tool-less depth adjustment

• Fires 16 – 50mm C1 series brad nails• Sequential & bump fire trigger• Tool-less depth adjustment

• Fires 32 – 65mm DA series finish nails• Sequential & bump fire trigger• Tool-less depth adjustment• Integrated air duster

• Lengths range from 25 – 65mm • 50 nails per row • Available in electro gal

• Lengths range from 25 – 64mm • Resin coated adhesive • Available in bright & electro gal

• Fires 25 – 65mm C series finish nails• Sequential & bump fire trigger• Tool-less depth adjustment• Integrated air duster

• Fires 13 – 38mm 6000 series narrow crown staples• Sequential & bump fire trigger• Tool-less depth adjustment

• Fires 38 – 57mm 15° plastic collated & 32 – 65mm 16° wire collated nails• Smart fire trigger for single and bump fire• Tool-less depth adjustment

• Lengths range from 50 – 90mm • Diameters range from 2.8 – 3.3mm • Available in smooth bright & mechanical gal

DISCLAIMEREffective from the 01/05/2013 to 30/06/2013 unless stock is sold out. Products are current at the time of printing but are subject to change without notice. Prices may vary from store to store. Accessories not included unless otherwise stated. Illustrations are for display purpose only. Not all items shown in this brochure are held in stock by retailers at all times. Orders can be taken for product not held in stock at time of enquiry. Errors and Omissions Excepted (E&OE). Brochure prepared by Hitachi Power Tools Australia Pty Ltd ABN 27 072 677 153 for use by participating retailers.

Accessories

www.hitachi-powertools.com.au

102 Piece Drill and Drive Bit Set 728492

• Hard plastic carry case for safe and easy storage• Suitable accessories for metal, wood, plastic and masonry applications

50 Piece Drill and Drive Bit Set 799961

• Hard plastic carry case for safe and easy storage• Suitable accessories for metal, wood, plastic and masonry applications

120 Piece Drill and Drive Bit Set 799962

• Hard plastic carry case for safe and easy storage• Suitable accessories for metal, wood, plastic and masonry applications

35 Piece Hi-Torq Bit Set 728699

17 Piece Drill and Drive Bit Set 728118G

• Impact rated for the toughest jobs• Hard plastic storage case for storage and durability

• Hard plastic stackable storage case for convenient storage and durability• Suitable accessories for metal, wood, plastic and masonry applications

45 Piece Drill and Drive Bit Set 115006

• Hard plastic storage case for storage and durability• Suitable accessories for metal, wood, plastic and masonry applications

18 Piece Hi-Torq Bit Set 728698

• Impact rated for the toughest jobs• Carry pouch for convenient storage

83-Piece Drill and Drive Bit Set 728493

• Carry pouch for convenient storage• Suitable accessories for metal, wood, plastic and masonry applications

3 Piece Socket Adapter Set 751970

Consisting of: • ¼” Hex. Drive to 1/4” Square Drive• ¼” Hex. Drive to 3/8” Square Drive• ¼” Hex. Drive to 1/2” Square Drive