12
HORNOS Y METALES S.A
HORNOS Y METALES S.A
THE COMPANY I
COMPANY HORNOS Y METALES S.A.
FOUNDED 1989 BY MR. ANGEL AGUIRRE PASTO
TURNOVER 8 MILLON EUROS IN 2011
30% SALES INCREASE SINCE 2009
MAJOR COMPLETED PROJECT 1,550.000 EUROS
EMPLOYEES 35 DIRECT AND INDIRECT 10 ENGINEERS
SURFACE AREA 1.200 M2
OFFICES AND SUBSIDIARIES HORNOS Y METALES S.A. (SPAIN) HORMESA AMÉRICA (COLOMBIA) HORMESA MÉXICO (MEXICO) HORMESA THAILAND (THAILAND) JUNG-HORMESA (BRAZIL) LABORATORY (SCOTLAND)
SALES IN 36 COUNTRIES, 4 CONTINENTS , OVER 350 SATISFIED CUSTOMERS
ADDRESS:
LAS MARINERAS, 13 - 17 28864 - AJALVIR (MADRID), ESPAÑA
TELEPHONE: +34 918 874 039
E-MAIL: [email protected]
WWW.HORMESA.COM, WWW.CONTICAST.COM
THE COMPANY II
SINCE HORMESA WAS FOUNDED IN 1988 THE COMPANY HAS SPECIALIZED IN EQUIPMENT, MATERIALS AND CUSTOM MADE SOLUTIONS FOR MELTING NON FERROUS METALS, COPPER, ALUMINIUM, ZINC AND OTHER METAL ALLOYS
A CUSTOMER ORIENTATED APPROACH AND A CONTINUOUS TECHNOLOGICAL DEVELOPMENT ENABLE US TO PROVIDE THE FOUNDRY MEN HANDS-ON SOLUTIONS FOR THEIR INDUSTRIAL PROCESSES
OFFICES AND REPRESENTATIONS
HEAD OFFICE OFICES
REPRESENTATIONS
HEAD OFFICE
HORNOS Y METALES S.A.
PRINCIPAL & OFFICES
HORMESA AMÉRICA
HORMESA MÉXICO
HORMESA THAILAND
JUNG-HORMESA
CONTICAST
REPRESENTATIONS
ARGENTINA, CHILE, PERU, USA, CUBA, ITALY, FRANCE, INDIA, MIDDLE EAST, EGYPT, TURKEY , HUNGARY, PORTUGAL, UKRANIA.
MANUFACTURING RANGE
• GAS AND FUEL- OIL HEATED CRUCIBLE FURNACES, BALE-OUT AND TILTABLE WITH A CAPACITY UP TO 800 KG. AL. • ELECTRICAL RESISTANCE HEATED CRUCIBLE FURNACES, BALE-OUT ANDTILTABLE FOR THE MELTING AND HOLDING OF
ALUMINIUM • REVERBERATORY, DRY AND WET HEARTH FURNACES AND TOWER FURNACES FOR MELTING AND HOLDING ALUMINIUM
WITH 1-2 CHAMBERS. • ELECTRICALLY HEATED FURNACES WITHOUT CRUCIBLE FOR HOLDING ALUMINIUM IN INJECTION CASTING PLANTS. • DOSING FURNACES FOR ALUMINIUM. • CHANNEL INDUCTION FURNACES FOR MELTING AND/OR HOLDING COPPER ALLOYS.
• HORIZONTAL CONTINUOUS CASTING PLANTS FOR BARS AND STEEL BILLETS FOR ROLLING. • CONTINUOUS CASTING PLANTS FOR PRECIOUS METALS AND SPECIAL ALLOYS. • UPWARD VERTICAL CONTINUOUS CASTING FOR COPPER AND BRASS WIRE ROD AND STRIP. • UPWARD VERTICAL CONTINUOUS CASTING FOR SPECIAL ALLOYS WIRE ROD. • DOWNWARD VERTICAL SEMI-CONTINUOUS CASTING FOR ALUMINIUM EXTRUSION BILLETS. • FINISHING AND REFINING METALLURGICAL PROCESSES: ALUMINIUM, COPPER, ZINC, LEAD. • COPPER PYRO-REFINING PLANTS. • COMPLETE PRODUCTION AND INTEGRAL CONSULTANCY PLANTS.
HCC PLANTS I
• HCC PLANT PROCESS DIAGRAM
VIBRATING CHARGING SYSTEM
INDUCTION MELTING SYSTEM
COOLING SYSTEM
Hot Water OUT
Cold Water IN
LAUNDERS
DIES COOLING SYSTEM
OUT
OUT
IN
IN
RV FURNACE
ROB FURNACE
TRACTION SYSTEM
CONTICAST SOFTWARE
AUTOMATIC SAW SYSTEM
MELTING HOLDING CASTING
HCC PLANTS II
• MELTING STAGE
• HIGH ELECTRICAL EFICIENCY • PRECISE CONTROL OF TEMPERATURE • HIGH PRODUCTION RATES • GOOD QUALITY OF MOLTEN METAL • CLEAN OPERATION
HORMESA SUPPLIES THEIR FURNACES PREPARED FOR WORKING, INCLUDYING ALL TECHNICAL ADVISE NEEDED FOR THE INSTALLATION, COMMISIONING, ANG SERVICE AFTER START UP.
HCC PLANTS III
• HOLDING STAGE (ELECTRIC FURNACE WITH GRAPHITE TECHNOLOGY - RV SERIES)
OUR RV FURNACES ARE PERFECT FOR APPLICATIONS WITH CHANGING OF ALLOYS. FOR CHANGING OF ALLOY IT IS NEEDED ONLY TO CHANGE CRUSIBLE. ALSO THE FURNACE IS PREPARE FOR QUICK CHANGE OF DIES.
FOR THIS PROJECT WE WILL USE THE RV FURNACE FOR BRONZES AND SPECIAL ALLOYS.
HCC PLANTS IV
• HOLDING STAGE (INDUCTION CHANNEL FURNACE)
OUR ROB TWIN CHAMBER FURNACES ARE PERFECT FOR HIGH PRODUCTION RATES WITHOUT CHANGING OF ALLOYS. IT HAS TWO CHAMBERS; ONE FOR CHARGING AND OTHER FOR CASTING. ALSO THE FURNACE IS PREPARE FOR QUICK CHANGE OF DIES.
FOR THIS PROJECT WE WILL USE THE ROB FURNACE FOR BRASSES AND HIGH PRODUCTION RATE METALS.
- HIGH ELECTRICAL EFFICIENCY - LONG LIFE OF REFRACTORY (AROUND 5 YEARS BEFORE CHANGE) - HYDRAULIC TILTING FOR EMPTYING AND CHANGE OF DIES
HCC PLANTS V
• CASTING STAGE (TRACTION SYSTEM)
HORMESA USES ALWAYS AC SERVO MOTORS FOR ALL ITS TRACTION SYSTEMS. IT ASSURES A SMOOTH SURFACE AND HIGH SPEED CASTING.
WITH OUR CONTICAST SOFTWARE WE CAN CONTROL SPEED, ACCELERATION, DESCELERATION, STOP TIME, AND NUMBER OF CYCLES FOR AUTO CLEANING IF NEEDED.
HORMESA PREPARE THE TRACTION SYSTEM FOR EASY ADJUSTING FOR CHANGING OF SIZES, AND NUMBER OF BRANDS.
HCC PLANTS VI
• CASTING STAGE (AUTOMATIC SAW CUTTING SYSTEM)
OUR AUTOMATIC SAW CUTTING SYSTEMS HAS THE CAPABILITY FOR CUTTING DIFFERENT SIZES AND NUMBER OF BRANDS, ANDJUSTMENT OF SPEED, AND LENGHT. ALL AUTOMATIC.
HORMESA ARRANGE ENTIRE CUSTOM PROJECTS; FROM APPROACHING, TO DESIGN OF ALL EQUIPMENT ACORDING TO THE NEEDS OF THE CUSTOMER. WE GUARANTEE THE ACHIEVEMENT OF ALL CUSTOMER REQUIREMENTS.
THANK YOU
