HOT MIX PLANT

  

PREPARED BY:PREPARED BY: Kamil S ChauhanKamil S Chauhan

  

GUIDED BY:GUIDED BY: Prof Manish Jain SirProf Manish Jain Sir

Quality Construction Equipment

ASPHALTBATCHMIX PLANTANP Series 60 - 240 tpx

1. INTRODUCTION:

Asphaltic concrete is a mixture of asphalt, coarse aggregates, fine aggregates & filler material. After mixing, we are heating them up to final product called “HOT MIX”.

There are two basic types of plants used to manufacture hot mix asphalt:

Batch type plant Drum(continuous) type plant

The various parts of Batch mix plant are given below as per flow of material:

1. Cold aggregate four-bin feeder.2. Cold conveyor.3. Aggregate dryer.4. Mixing Chamber5. Asphalt tank.6. Mineral filler unit.7. Load-out conveyor.8. Centralized control panel.

ASPHALT BATCH MIX PLANT

ANP Series 60 - 240 tph

Cold aggregates four – bin feeder: -

1. It consists of FOUR independent top open type bins having being fabricated from MS plate mounted on rigid Channel supported on channel. Each bin consists of an independent and synchronized variable speeds D.C. motor for feeding the aggregates at a predetermined rate through a precisely adjustable bin quadrant gate.

2. Gathering conveyor belt equipped with an electronic weigh bridge and driven by electric motor.

3. Single deck screen provided at the discharge end of the gathering conveyor for rejection of any paver size material above permissible limit.

4. Single main transfer conveyor to receive the aggregates from the gathering conveyor and discharge it into the dryer under the combustion zone driven by electric motor and reduction gear

COLD AGGREGATE COLD AGGREGATE CONVEYORCONVEYOR

Separate detachable slinger conveyor is provided to transfer the aggregates received from the vibratory screen to feed into the thermo- drum. Slinger conveyor is driven by constant speed electric motor coupled with reduction gearbox.

The rigid frame of conveyor is fabricated from appropriate channel sections and the conveyor belt is supported by uniformly spaced roller stands. Any sagging on the return travel of the belt is also taken care-of by roller.

AGGREGATE DRYERAGGREGATE DRYER

From the cold aggregates conveyor, aggregates are delivered to the dryer. The dryer removes moisture from the aggregates and rises temperature to the desired level. The dryer has an oil or gas burner with a blower fan to provide the primary air for combustion of the fuel, and an exhaust fan to create a draft through the dryer.

Proper aggregate temperature is essential. Aggregates that are heated to an excessive temperature can harden the binder during mixing. Under heated aggregates are difficult to coat thoroughly with binder and the resulting mix is difficult to place on the roadway.

MIXING CHAMBERMIXING CHAMBER

In this chamber the binder & aggregates are mixed. It consists of a lined mixing chamber with horizontal shaft about which the drum rotates. The chamber is so designed that there are no dead areas formed. The temperature of the mix shall be maintained properly so as to have homogeneous mix.

The whole assembly of Chamber is supported over prefabricated steel sections preferably of channel or I-sections.

ASPHALT TANKASPHALT TANK

The bitumen section of batch mix plant mainly consists of bitumen tank, bitumen heating burner, bitumen pumping & metering unit and hot oil system.

The tank is fully insulated to minimize heat losses and is of 15,000 liters. capacity. The bitumen inside the tank is heated by U-shaped heating tube fitted with automatic burner of adequate capacity. A jacketed bitumen pump driven by variable speed motor through reduction gearbox is provided to pump the bitumen to the drum. The bitumen flow rate is controlled by varying the RPM of motor.

Hot mix storage silos can be offered with options to store different types of mix designsto meet varied site demands.

•Mineral filler unit: The Filler hopper is provided to add mineral filler from a separate hopper, in the mix to the extent pre-selectable in percentage by weight of the maximum plant output. The unit is fabricated from 5 m thick steel plate and mounted on steel structure. The system is powered by a variable speed motor coupled with gearbox to rotary valve and also synchronized with aggregate & bitumen output. The filler material from this unit is conveyed automatically up to coated zone in the pug-mill.

LOAD OUT CONVEYORLOAD OUT CONVEYOR

Hot mix material discharged from the pugmill is carried by inclined hot conveyor belt and discharged into the tipper / truck through hydraulically operated surge storage hopper.

Hydraulically operated storage hopper is provided at the discharge end of the conveyor which stores the hot mix and allows it to fall as mass in the batches and thus avoids segregation and spillage during out cycle.

CONTROL SYSTEM

The plant is supplied with centralized control panel. All controls, including the motor control, center circuit breakers are provided in the control panel. The control panel controls feeder bin controls and electric switchgear. All the parameters like, temperature of bitumen-hot mix material-exhaust gases and aggregate weight, asphalt percentage, hot mix material weight etc. are displayed on the control panel.

4. Initial investment of batch mix plant The initial cost of drum mix plant depends on its capacity. The general market value of a drum mix plant varies in between 60.0 lacs to 75.0 lacs as per their capacity.

5. Companies manufacturing drum mix plant Apollo engineering ltd. Ahemdabad.

Veshwakarma engineers ltd. Borsad Dhruvi scaffoldings (B) ltd. Mehsana

Speed-crafts ltd. Patna. & Many more all over India.

ReferencesReferences

•Wikipedia •www.apollo.co.in•www.asphaltplant.cn•Apollo Engineering ltd. Ahmedabad.