Huawei EchoLife ONT V100R003C00&C01 Function List(28-Sep-2011) · PDF fileHuawei EchoLife ONT...

Huawei EchoLife ONT V100R003C00&C01 Function List(28-Sep-2011)

Issue V3.2

Copyright © Huawei Technologies Co., Ltd. 2009. All rights reserved.

No part of this document may be reproduced or transmitted in any form or by any means without prior written consent

of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective holders.

Notice

Your purchased products, services, and features shall be restricted by Huawei commercial contract and conditions. All

or certain of products, services, or features described in this document may not be included in what you purchased or

used. Unless otherwise specified in the contract, all statements in this document do not constitute the warranty of any

kind, express or implied.

The information in this document is subject to change without notice. Every effort has been made in the preparation of

this document to ensure accuracy of the contents, but all the statements, information, and recommendations in this

document do not constitute the warranty of any kind, express or implied.

第 1 页

HG8240 HG8242 HG8245 HG8247 HG8010 HG8110 HG8447

GPON UplinkGPON InterfaceFeatures √ √ √ √ √ √ √

Comply with the system requirementsand architecture defined in G.984.1,G.984.2, G.984.3, and G.984.4 √ √ √ √ √ √ √Support GEM encapsulation √ √ √ √ √ √ √The GPON system is a single-fiberbi-directional system and useswavelengths 1310 nm in the upstreamdirection and wavelengths 1490 nm inthe downstream direction. √ √ √ √ √ √ √For bi-directional data transmissionbetween the OLT and the ONTs, asingle-mode optical fiber defined byG.652 is used. √ √ √ √ √ √ √

Support the embedded Operation,Administration, and Maintenance(OAM) message,the physical layer OAM(PLOAM) message,the OMCI message √ √ √ √ √ √ √Maximum downstream rate: 2.488Gbit/s √ √ √ √ √ √ √Maximum upstream rate: 1.244 Gbit/s √ √ √ √ √ √ √Maximum logical reach of an ONT: 60km(defined by G.984.1);Maximum distance between thefarthest and nearest ONTs: 20 Km √ √ √ √ √ √ √

Level-I Feature Level-II Feature SpecificationsV100R003C00&C01

第 2 页

HG8240 HG8242 HG8245 HG8247 HG8010 HG8110 HG8447Level-I Feature Level-II Feature Specifications

V100R003C00&C01

Support NRZ coding and scrambling inupstream and downstream direction. √ √ √ √ √ √ √Support the fragment of data packetsand OMCI packets, and the length offragment can be adaptive or fixedmode(in defaulted).The length rangeis 32~2048Byte and the granularityis 8 Byte. √ √ √ √ √ √ √Support packet reforming indownstream √ √ √ √ √ √ √Compatible with the NGPON wavelengthdefined in G.984.5. √ √ √ × √ √ ×

GEM port √ √ √ √ √ √ √

Support 32 GEM ports. √ √ √ √ √ √ √

Support the configurable downstreammulticast GEM port √ √ √ √ √ √ √

Support the mapping between the GEMport and the T-CONT √ √ √ √ √ √ √

Support to map the traffic stream tothe GEM port by:1. VLAN2. VLAN + PRI3. PRI4. IPToS5. Ethernet port6. Ethernet port + VLAN7. Ethernet port + PRI8. Ethernet port + VLAN + PRI √ √ √ √ √ √ √

T-CONT √ √ √ √ √ √ √Support 8 T-CONT √ √ √ √ √ √ √

第 3 页


V100R003C00&C01

Support T-CONT type 1, 2, 3, 4, 5 √ √ √ √ √ √ √Support multiple GEM Port for eachT-CONT √ √ √ √ √ √ √

DBA(DynamicBandwidthAllocation) √ √ √ √ √ √ √

Support SR、NSR mode of DBA，SR modein defauted. √ √ √ √ √ √ √Support DBA Piggy-back DBRu Mode 0 √ √ √ √ √ √ √

FEC √ √ √ √ √ √ √

Support FEC in downstream andupstream direction,support FECdecoding in downstream direction andFEC coding in upstream direction

√ √ √ √ √ √ √

Encryption √ √ √ √ √ √ √Support the encryption of unicastdata channel;Support the encryption of OMCIchannel. √ √ √ √ √ √ √Support AES-128 encryption. √ √ √ √ √ √ √Support the dynamic key exchange：the generation of key and thedynamic key exchange according tothe pre-defined time √ √ √ √ √ √ √

OMCI √ √ √ √ √ √ √OMCI channel √ √ √ √ √ √ √Comply with both new and old OMCIstandards √ √ √ √ √ √ √OMCI MIB Upload √ √ √ √ √ √ √

第 4 页


V100R003C00&C01

Support to handle the over-sizedattribute of OMCI message √ √ √ √ √ √ √ONT reset through OMCI √ √ √ √ √ √ √Support to report the response timethrough OMCI, for measuring distanceexactly √ √ √ √ √ √ √OMCI alarm synchronization √ √ √ √ √ √ √Support to synchronize time of theOLT √ √ √ √ √ √ √Service provision through OMCI √ √ √ √ × √ √

OMCIconfigurationmanagement √ √ √ √ √ √ √

Support to configure T-CONT throughOMCI √ √ √ √ √ √ √

Support to configure GEM portthrough OMCI, and support toconfigure the binding between theGEM port and the T-CONT through OMCI √ √ √ √ √ √ √Support to configure mapping thetraffic stream to the GEM port by:1. VLAN2. VLAN + PRI3. PRI4. Physical port5. IPToS6. Physical port + VLAN7. Physical port + PRI8. Physical port + VLAN + PRI √ √ √ √ √ √ √

第 5 页


V100R003C00&C01

Support mapping the SDCP priorityinto 802.1P priority based on VLAN √ √ √ √ √ √ √Support to configure VLAN of theEthernet interface through OMCI √ √ √ √ √ √ √

Support to configure Native VLAN ofthe Ethernet interface, and only oneVLAN can be assighed as the NativeVLAN for each Ethernet interface √ √ √ √ √ √ √

Support to configure the VLANtransparent transmission based onthe Ethernet interface through OMCI,and the Ethernet interface supportsto forward the packets with any VLAN √ √ √ √ √ √ √Support to configure the VLAN andPriority translation of the Ethernetinterface through OMCI √ √ √ √ √ √ √Support to configure the N:1 VLANtranslation through OMCI √ √ √ √ √ √ √Support to enable/disable theEthernet interface, configure thenegotiation mode, speed and duplexmode of the Ethernet interfacethrough OMCI √ √ √ √ √ √ √

Support to configure the PQscheduling mode of the GEM portthrough OMCI √ √ √ √ √ √ √

Support to configure the CAR settingbased on GEM port through OMCI

√ √ √ √ √ √ √

第 6 页


V100R003C00&C01

Support to configure the CAR settingbased on service flow through OMCI

√ √ √ √ √ √ √Support to configure the upstreamand downstream rate limit based onEthernet interface through OMCI √ √ √ √ √ √ √Support to configure the queuescheduling mode of SP, WRR or SP+WRRthrough OMCI,and the default queuescheduling mode is SP √ √ √ √ √ √ √Support to configure the weight ofWRR queue through OMCI, and theweight range is 1～100 √ √ √ √ √ √ √Support to configure QinQ functionof the Ethernet interface throughOMCI, and the outer VLAN andpriority of QinQ uses the Nativevlan and priority of the Ethernetinterface √ √ √ √ √ √ √Support to configure the MAC addressaging time through OMCI √ √ √ √ √ √ √Support to enable/disable MACaddress learning through OMCI √ √ √ √ √ √ √Support to configure the pause flowcontrol based on Ethernet interface √ √ √ √ √ √ √Support to configure the multicastfiltering entries through OMCI √ √ √ √ √ √ √

第 7 页


V100R003C00&C01

Support to configure multicast modethrough OMCI, including translation,removing, and transparentlytransmitting the downstreammulticast VLAN √ √ √ √ √ √ √Support to configure the VLANtranslation of IGMP message inupstream direction through OMCI, andno translation is the defaultconfiguration √ √ √ √ √ √ √Support to configure the multicastGEM port through OMCI √ √ √ √ √ √ √Support to enable/disable RFinterface through OMCI × × × √ × × √Support to enable/disable the BPDUtransparent transmission throughOMCI √ √ √ √ √ √ √Support to configure GEM portloopback through OMCI √ √ √ √ √ √ √Support to configure the loopback ofthe Ethernet interface through OMCI,and support to loopback the trafficback to the OLT on the Ethernetinterface of the ONT √ √ √ √ √ √ √Support to configure the alarmthreshold of the Ethernet interfacethrough OMCI √ √ √ √ √ √ √Support to configure the switch ofPOTS interface √ √ √ √ × √ √

第 8 页


V100R003C00&C01

support to configure turning on/offthe multicast function of any portthrough OMCI

√ √ √ √ √ √ √

support to configure VLAN of theuplink packets andtranslating/adding/transparenttransmission the VLAN/priority ofuplink packets through OMCI.

√ √ √ √ √ √ √

OMCI querymanagement √ √ √ √ √ √ √

Support to query the status,negotiation mode, speed and duplexmode of the Ethernet interface. √ √ √ √ √ √ √Support to query the deviceinformation through OMCI, includingthe software and hardware version √ √ √ √ √ √ √Support to query the optical moduleparameters through OMCI, includingthe transmitting optical power,receiving optical power, workingvoltage, temperature and biascurrent. If the optical modulesupports optical parametersmonitoring, the correct parametersare returned；otherwise, the nullvalue is returned. √ √ √ √ √ √ √Support to query the statistics ofEthernet interface through OMCI √ √ √ √ √ √ √

第 9 页


V100R003C00&C01

Support to query the MAC address ofsome indicated VALN of someindicated Ethernet interface throughOMCI √ √ √ √ √ √ √Support to query the switch of POTSinterface √ √ √ √ × √ √

support downlead FEC statisticincluding Corrected bytes,Correctedcode words,Uncorrectable code wordsand Total code words. The statisticis implemented every 15 minutes andthe statistic threshold alarm issuppoted.

√ √ √ √ √ √ √

Support to configure the error codein XML files through OMCI

√ √ √ √×

√ √

support to qinquery managementstatus,connection status,physicalstatus,hook on/off status,servicestatus and service sype of POTSinterface thourgh OMCI

√ √ √ √

×

√ √

Alarm reportthrough OMCI √ √ √ √ × √ √

第 10 页


V100R003C00&C01

Support backup battery alarm,including:1.Powering alarm: Loss of externalpower2.Battery missing: Battery isprovisioned but missing3.Battery failure: Battery isprovisioned and present but cannotrecharge4.Battery low: Battery isprovisioned and present but itsvoltage is too low √ √ √ √ × √ √Support Ethernet interface up/downalarm √ √ √ √ √ √ √Support Ethernet interface thresholdalarm √ √ √ √ √ √ √Support watchdog alarm √ √ √ √ √ √ √

ONTAuthentication √ √ √ √ √ √ √

Support the registration of ONT asdefined in G.984.3 √ √ √ √ √ √ √Support SN, Password or SN +Password authentication to activatethe ONT √ √ √ √ √ √ √Support to process the Passwordmessage and report the passwordinformation to OLT √ √ √ √ √ √ √

ONT re-registerprocessing √ √ √ √ √ √ √

第 11 页


V100R003C00&C01

Support to re-register to the OLTafter receiving the re-registermessage from the OLT √ √ √ √ √ √ √

ONTdeactivate/activate processing √ √ √ √ √ √ √

Support to stop optical transmissionand go into deactive state afterreceiving the disable message fromthe OLT, and to pop up afterreceiving the activate message fromthe OLT √ √ √ √ √ √ √

Support to detectrogue ONT andshut down rogueONT √ √ √ √ √ √ √

Support rogue ONT message，andsupport to open up/shut down thetransmit power of the opticaltransceiver according to the messagefrom OLT √ √ √ √ √ √ √

Other GPON linefeature √ √ √ √ √ √ √

BIP error statistics √ √ √ √ √ √ √Support PEE message √ √ √ √ √ √ √Support to generate the RDIi signalwhen detecting the SD, Sdi or LCDG,and to report the RDIi signal to OLTthrough upstream PLOu. √ √ √ √ √ √ √

第 12 页


V100R003C00&C01

PerformanceStatistics √ √ √ √ √ √ √

Support the performance statisticsof Ethernet interface √ √ √ √ √ √ √

GPON Performance √ √ √ √ √ √ √Delay: The GPON system (the OLT andONTs included) has a maximum meansignal transfer delay of 1.5ms asspecified in G.984.1. √ √ √ √ √ √ √Jitter: The GPON system (the OLT andONTs included) complies with thejitter transfer jitter tolerance andjitter generation limits specifiedin G.984.2. √ √ √ √ √ √ √

Support tosynchronize theline clock fromthe OLT √ √ √ √ √ √ √

Support to synchronise to the OLT,and an internal free run clock withan accuracy of 50ppm is available ifthe OLT clock is lost. √ √ √ √ √ √ √

Maintenance andDiagnose √ √ √ √ √ √ √

Support the loopback test of theEthernet interface √ √ √ √ √ √ √Support the loopback test of GEMport √ √ √ √ √ √ √Support to report the Dying_Gaspalarm when the ONT is powered off. √ √ √ √ √ √ √

第 13 页


V100R003C00&C01

IPV6

support transparent transmission ofIPv6 layer 2 packets

√ √ √ √ √ √ √

Support MLDv1 packets(Query，Report，Done),support MLDv2packets(Query，Report)

√ √ √ √ √ √ √

the LAN bound with bridge WANinterface support MLD snooping

√ √ √ √ √ √ √

Optical module √ √ √ √ √ √ √

Comply withG.984.2Amd1（Class B+）standard.

√ √ √ √ √ √ √

The range of mean launched power is0.5dBm~5dBm.The minimum receiver sensitivity is-27dBm.The Minimum overload optical poweris -8dBm.Link Budget:The range of opticalloss is 13~28dB.

√ √ √ √ √ √ √

Support OPM √ √ √ √ √ √ √

Support to query optic status(sendlight normally/initiatively sendlight always/shut down transmitterpower),sending optic power,receiving optic power,workingvoltage and working temperature.

√ √ √ √ √ √ √

第 14 页


V100R003C00&C01

Support to query the receiving opticpower of CATV.

× x × √ x x √

Ethernet Access√ √ √ √ √ √ √

GE interfacefeature

Ethernet interface complies withIEEE 802.3ab

√ √ √ √ √ √ √

Ethernet interface supports theauto-negotiation of the rate and theduplex mode by default.

√ √ √ √ √ √ √

Each Ethernet interface supportsdefined speed 10Mbps,100Mbps or1000Mbps.

√ √ √ √ √ √ √

Each Ethernet interface supportsdefined full duplex or half duplex.

√ √ √ √ √ √ √

Ethernet interface supports theautomatic MDI/MDI-X.

√ √ √ √ √ √ √

Ethernet interface supports the flowcontrol through Pause (IEEE 802.3Annex 31B).

√ √ √ √ √ √ √

Support upstream and downstream ratelimit based on Ethernet interface,and the granularity is 64kbps.

√ √ √ √ √ √ √

Not support JUMBO Ethernet frame，support up to 2000 Bytes Ethernetframe.

√ √ √ √ √ √ √

WLAN Access × × √ √ × × √

Enable/disablethe WLAN function

× × √ √ × × √

第 15 页


V100R003C00&C01

Support to enable/disable the WLANfunction through Web or externalhardware switch, and this functionis enabled by default.

× × √ √ × × √

The status of the Web and the stateof the external hardware switch ofthe ONT should be the same.

× × √ √ × × √

Standards × × √ √ × × √

Comply with IEEE 802.3u × × √ √ × × √Comply with IEEE802.11n/802.11b/802.11g.

× × √ √ × × √

Comply with IEEE 802.11e and IEEE802.11i

× × √ √ × × √

SSID × × √ √ × × √

Support four SSID(SSID-1, SSID-2,SSID-3, and SSID-4 respectively).

× × √ √ × × √

By default, only SSID-1 is used. × × √ √ × × √Support to enable/disable thebroadcast of each SSID, and SSIDbroadcast is enabled by default.

× × √ √ × × √

Support the encryption setting foreach SSID.

× × √ √ × × √

Automatic rateadjustment

× × √ √ × × √

Support the automatic rateadjustment.

× × √ √ × × √

Working channel× × √ √ × × √

第 16 页


V100R003C00&C01

Support 13 working channels（channel1～13），and the channel rangecomplies with the requirement of802.11.

× × √ √ × × √

Support the automatic channelselection and manual configurationfor the channel. By default, theautomatic channel selection is used.

× × √ √ × × √

In the automatic channel selectionmode, ONT selects the channel amongchannels 1–11.

× × √ √ × × √

Power saving modeof STA

× × √ √ × × √

Support the STA to work in the powersaving mode, identify the STA toenter the power management mode,buffer the related data, wake up theSTA through the Beacon frame, andtransmit the buffered data

× × √ √ × × √

Transmit poweradjustment

× × √ √ × × √

Support to adjust the transmitpower.The maximum transmit power(including the antenna gain) of theoverall system is 85～100 mW, 100mwby default.For the configuration, only 25%、50%、75%、100% can be choosed forusers(100% complys to 100mW).

× × √ √ × × √

Statistics × × √ √ × × √

第 17 页


V100R003C00&C01

Support the statistics of packetsreceived and sent in WLAN interface,including the number of bytesreceived and sent, the number ofpackets received and sent, thenumber of error packets received andsent, the number of discardedpackets received and sent.

× × √ √ × × √

Support diversityreception

× × √ √ × × √

Support diversity reception × × √ √ × × √AccessAuthenticationMode

× × √ √ × × √

Open System Authentication：Authentication message is notencrypted. All STAs which requestauthentication can access ONT.After authentication, data messagescan be encrypted by WEP.

× × √ √ × × √

Shared key Authentication：Authentication message is encryptedby WEP. After authentication, datamessages are also encrypted by WEP.

× × √ √ × × √

第 18 页


V100R003C00&C01

WPA (WiFi protected access)Authentication：It was developed byWi-Fi alliance based on IEEE 802.11iDraft 3.0 in 2002. Authenticationuses 802.1x, and RADIUSauthentication server is required.It is suitable for enterprise users.Authentication and data messagesboth need encryption.

× × √ √ × × √

WPA2 Authentication：IEEE 802.11istandard is officially establishedin 2004, Wi-Fi alliance adopts itand it is also called WPA 2.0. It issuitable for enterprise users.

× × √ √ × × √

WPA-PSK Authentication：Key isshared previously. Authenticationand data messages both needencryption. It is suitable for homeusers.

× × √ √ × × √

WPA2-PSK Authentication：The secondversion of WPA-PSK. It is suitablefor home users.

× × √ √ × × √

WPS (WiFi protected setup)Authentication: It is a standard foreasy and secure establishment of awireless home network, created bythe Wi-Fi alliance and officiallylaunched on January 8, 2007. Itincludes Push button mode and PINmode.

× × √ √ × × √

第 19 页


V100R003C00&C01

Encryption × × √ √ × × √

Support 64-bit and 128-bit WEPencryption and the key can beentered by using HEX or ASCIIcharacters

× × √ √ × × √

Support WPA-PSK, WPA2-PSK,WPA andWPA2，and support AES,TKIP andAES+TKIP encryption. By default,WPA-PSK is used.

× × √ √ × × √

Support Encryption algorithm and keyare negotiated according to WPSstandard.

× × √ √ × × √

USB Interface × × √ √ × × √

Comply with USB2.0 and USB1.1specifications

× × √ √ × × √

USB1.1：full speed 12Mbps，low speed1.5MbpsUSB2.0：Compatible with USB1.1,while providing the highest rate of480Mbps

× × √ √ × × √

Support USBstorage device

× × √ √ × × √

Support Plug and PlaySupport hot plug

× × √ √ × × √

1.USB can be configured through Webbrowser；2.As FTP client, the files in FTPcan be loaded to USB storage device.

× × √ √ × × √

第 20 页


V100R003C00&C01

the storage devices connectedthrough USB works as FTP server

× × √ √ × × √

Support USB HUB× × √ √ × × √

USB interface can carry 2 storagedevices through the root hubs.

× × √ √ × × √

Support to readand write theFAT32/FAT filesystem

× × √ √ × × √

Support to read and write datacorrectly for file system of USBstorage device in form of FAT32/FAT

× × √ √ × × √

Support to read and write datacorrectly for file system of USBstorage device in form of NTFS

× × √ √ × × √

Support the USBstorage device tobeloaded/unloadedautomatically

× × √ √ × × √

USB Back-up × × √ √ × × √

Support to backup configration filesthrough the USB interface

× × √ √ × × √

Support to recover configrationfiles through the USB interface

× × √ √ × × √

RF Interface × √ × √ × × √

Standard 《GYT106-1999 Cable televisionbroadcasting system specifications》

× √ × √ × × √

第 21 页


V100R003C00&C01

Enable/disable RFinterface

Support to enable/disable RFinterface from BMS

× √ × √ × × √

Interface Type F-type × √ × √ × × √Workingwavelength 1540nm～1560nm

× √ × √ × × √

Frequency range54MHz～870MHz

× √ × √ × × √

Received averageoptical power

-8dBm～+2dBm× √ × √ × × √

Radio frequencyoutput power

≥17dBmV/Ch× √ × √ × × √

Radio frequencyoutput impedance

75Ω

× √ × √ × × √

L2 feature √ √ √ √ √ √ √

The structure ofEthernet Frame

√ √ √ √ √ √ √

Complies with Ethernet II (RFC894)or 802.3 SNAP (RFC1042)

√ √ √ √ √ √ √

MAC addressmanagement

√ √ √ √ √ √ √

Support 1024 MAC address entries √ √ √ √ √ √ √Support to set the MAC address agingtime,the range of the MAC addressaging time is 10s～1000000s, thedefault is 300s.

√ √ √ √ √ √ √

第 22 页


V100R003C00&C01

Support to enable/disable MACaddress learning

√ √ √ √ √ √ √

VLAN √ √ √ √ √ √ √

Support 8 VLAN for each Ethernetinterface

√ √ √ √ √ √ √

Support VLAN transparenttransmission based on Ethernetinterface

√ √ √ √ √ √ √

Support VLAN translation based onEthernet interface，and eachEthernet interface supports 4translation rules

√ √ √ √ √ √ √

Support N:1 VLAN translation and 1:1VLAN translation

√ √ √ √ √ √ √

QinQ √ √ √ √ √ √ √

GPON ONT support QinQ function basedon the Ethernet interface, which canbe configured though OMCI.

√ √ √ √ √ √ √

The outer VLAN of QinQ uses theNative vlan of the Ethernetinterface.

√ √ √ √ √ √ √

The priority of the outer VLAN canbe configured as copying the inner802.1p priority or using thespecified priority of the Ethernetinterface.

√ √ √ √ √ √ √

GPON ONT support QinQ function basedon VLAN, which can be configuredthrough OMCI.

√ √ √ √ √ √ √

第 23 页


V100R003C00&C01

Support the L2communication andisolation betweenethernet ports

√ √ √ √ × × √

Support the L2 communication andisolation between ethernet ports，L2communication by default

√ √ √ √ × × √

LAN interfaceworking mode

× × √ √ × × √

Support each Ethernet interface towork in L2 or L3 mode

× × √ √ × × √

The default working mode of SSID isL3 mode

× × √ √ × × √

VLAN and priorityprocess

√ √ √ √ √ √ √

Support to mark the untagged packetswith the default VLAN and priorityof Ethernet interface in upstreamand discard the VLAN tag indownstream

√ √ √ √ √ √ √

Support VLAN filter in upstreamSupport 8 VLAN for each Ethernetinterface

√ √ √ √ √ √ √

Support VLAN and 802.1p translationbased on Ethernet interface √ √ √ √ √ √ √

Support VLAN and 802.1p translationbased on VLAN plus 802.1p √ √ √ √ √ √ √

Support to specify the VLAN and802.1p based on Ethernet type. √ √ √ √ √ √ √

第 24 页


V100R003C00&C01

Support to indicate VLAN and PRIafter translation. √ √ √ √ √ √ √support to copy original prioritywhen VLAN translation. √ √ √ √ √ √ √

TrafficClassification/Traffic Mapping

√ √ √ √ √ √ √

based on VLAN √ √ √ √ √ √ √based on VLAN+PRI √ √ √ √ √ √ √based on PRI √ √ √ √ √ √ √based on IPToS √ √ √ √ √ √ √based on Ethernet port √ √ √ √ √ √ √based on Ethernet port + VLAN √ √ √ √ √ √ √based on Ethernet port + PRI √ √ √ √ √ √ √based on Ethernet port + VLAN + PRI √ √ √ √ √ √ √

Traffic transparent transmission

Support the traffic transparenttransmission on the indicated VLANin Vlan mapping mode;and support transmit the IPv6Packets transparently with indicatedVLAN

√ √ √ √ √ √ √

第 25 页


V100R003C00&C01

Support the traffic transparenttransmission on the indicatedVlan+Pri in Vlan+Pri mapping mode;and support transmit the IPv6Packets transparently with indicatedVLAN+Pri

√ √ √ √ √ √ √

Support the traffic transparenttransmission on the indicatedPort+Vlan in Port+Vlan mapping mode;and support transmit the IPv6Packets transparently with indicatedPort+Vlan

√ √ √ √ √ √ √

Support the traffic transparenttransmission on the indicatedPort+Vlan+Pri in Port+Vlan+Primapping mode;

√ √ √ √ √ √ √

support to configure and delete thetraffic transparent transmissionthrough OMCI

√ √ √ √ √ √ √

CAR √ √ √ √ √ √ √

Support the CAR setting based onethernet port

√ √ √ √ √ √ √

Support the CAR setting based on GEMport

√ √ √ √ √ √ √

第 26 页


V100R003C00&C01

Support the CAR setting based onservice flow

√ √ √ √ √ √ √

Traffic mappingto priority queue

√ √ √ √ √ √ √

Support to map the upstream trafficto the priority queue of the T-CONTbased on 802.1p, and map thedownstream traffic to the priorityqueue of the Ethernet port based on802.1p

√ √ √ √ √ √ √

Allow the operator to configuremapping the upstream traffic to thepriority queue of the T-CON

√ √ √ √ √ √ √

Queue scheduling√ √ √ √ √ √ √

Support the queue scheduling mode of4 SP(Strict Priority) queues, 4WRR(Weighted Round Robin) queues or4 SP+WRR queues based on the T-CONTin the upstream direction,and thedefault queue scheduling mode is SP

√ √ √ √ √ √ √

Support the queue scheduling mode of4 SP queues, 4 WRR queues or 4SP+WRR queues based on the Ethernetinterface in the downstreamdirection，and the default queuescheduling mode is SP

√ √ √ √ √ √ √

CongestionManagement

√ √ √ √ √ √ √

第 27 页


V100R003C00&C01

Support Drop Tail mechanism to avoidcongestion

√ √ √ √ √ √ √

MulticastFeature

√ √ √ √ √ √ √

GPON MulticastFeature

√ √ √ √ √ √ √

Controlled and uncontrolledmulticast modes

√ √ √ √ √ √ √

Quick leave attribute √ √ √ √ √ √ √IGMP V2&V3 snooping √ √ √ √ √ √ √Support to forward multicast toEthernet interface which join themulticast group

√ √ √ √ √ √ √

Support to filter and forward basedon multicast MAC

× × × × × × ×

Different GEM port for multicaststream and IGMP messages indownstream direction

√ √ √ √ √ √ √

Multicast GEM Port is configurable √ √ √ √ √ √ √Support to translate, remove ortransparently transmit multicastVLAN

√ √ √ √ √ √ √

Support VLAN translation of IGMPmessages in upstream and downstreamdirection

√ √ √ √ √ √ √

Multicast performance √ √ √ √ √ √ √Support the authentication based onGemport √ √ √ √ √ √ √

Multicast groups √ √ √ √ √ √ √Support bridge WAN multicast √ √ √ √ √ √ √

第 28 页


V100R003C00&C01

support to enable/un-enable themultcast function of any port.

√ √ √ √ √ √ √

support to configure portchanging/adding/transparenttransmission VLAN/priority of uplinkIGMP packts

√ √ √ √ √ √ √

support to configure ONT multicastVLAN of any port includingdeleting/tranlation/transparenttransmission through OMCI

√ √ √ √ √ √ √

support to limite packet functionagainst protocol packets

√ √ √ √ √ √ √

L3 feature × × √ √ × × √

WAN InterfaceFeature

× × √ √ × × √

Support 4 WAN interface and the WANinterface to have the uniqueavailable MAC address

× × √ √ × × √

Support the WAN interface to havethe unique available MAC address

× × √ √ × × √

Support（RFC2516）PPPoE client andthe IP address is obtained throughPPPoE

× × √ √ × × √

Support DHCP client and the IPaddress is obtained through DHCP

× × √ √ × × √

Support to configure the static IPaddress

× × √ √ × × √

第 29 页


V100R003C00&C01

The type of the WAN interfacesupports Internet,VOIP,TR069 and thecombination of these three types

× × √ √ × × √

Support to enable/disable WANinterface

× × √ √ × × √

WAN interface supports the workingmode of Router

× × √ √ × × √

WAN interface supports the workingmode of Bridge

× × √ √ × × √

Support to bind the Ethernetinterface or SSID with the WANinterface，that is, support todesignate one or multiple Ethernetinterfaces or SSID to the WANinterface

× × √ √ × × √

Router WAN interface support IPaddress filter, Anti-dos, ACL, NAPT,ALG features

× × √ √ × × √

Support PPPoE always online, thatis, the connection is notinterrupted regardless of dataexisting

× × √ √ × × √

第 30 页


V100R003C00&C01

Support to defer the termination ofPPPoE sessions for 2 minutes whenthe GPON connection is lost. If theGPON connection is restored during 2minutes, support to attempt to useits previous PPPoE session settings.If these are rejected, then theoriginal PPPoE session can beterminated and a new PPPoE sessionattempted.

× × √ √ × × √

The WAN interface getting IP addressthrough PPPoE supprots OnDemandmodle: it support disconnect the WANcononection in idle time and re-dialif WAN data happens again. and theidle time can be configued at least3 mintues.

× × √ √ × × √

The WAN interface getting IP addressthrough PPPoE supprots Mannualmodle:the redial process should bedone by mannual

× × √ √ × × √

Support to get WAN interfaceconnection time and LCP parametersof PPPoE WAN interface

× × √ √ × × √

the WAN interface supports IPv4/IPv6dual stack and support transparenttransmission of IPv6 Layer 2 packets

× × √ √ × × √

第 31 页


V100R003C00&C01

Bridge WAN interface support toforward packet according to lay2protocol type in LAN side throughTR069

× × √ √ × × √

Support to configure WAN interfaceincluding:1,enable/disable2,WAN interface type3,VLAN and priorityc4,NAT enable5,the way to get address6,the LAN interface or SSID banded7,static IP address,subnetwork maskand gateway address8,static master/stand-by DNS address9,PPPoE username,password and etc

× × √ √ × × √

桥接WAN口支持MLD SnoopingBridge WAN interface support MLDSnooping

× × √ √ × × √

Support Any Port Any Servicefeature，Internet、IPTV andVOIPservice can band with ONT portsautomatically;Support any Port Any Serviceswitch；Support to configue WAN interfaceservice label；Support configure through TR069,XMLfile and WEB

× × √ √ × × √

第 32 页


V100R003C00&C01

Support internet and IPTV servicethrough any ETH interface and SSIDin route mode

× × √ √ × × √

ARP × × √ √ × × √

Support up to 512 ARP entries × × √ √ × × √Support up to 32 static ARP entriesand support to add,delete and querythe static ARP entries

× × √ √ × × √

the default ARP aging time is 60s × × √ √ × × √support ARP-Ping function and sendnew DHCP require to get new gatewayIP address

× × √ √ × × √

support to configure parameters ofARP-Ping function

× × √ √ × × √

when the WAN interface isopened/stopped/deleted, the ARP-Pingfunction will also be opened/stopped

× × √ √ × × √

Static route × × √ √ × × √

Support up to 32 static routeentries

× × √ √ × × √

Support to add,delete or querystatic route entry

× × √ √ × × √

support to configure and check thestatic route for the telecomadminstrater level users

× × √ × × × ×

Default route × × √ √ × × √

第 33 页


V100R003C00&C01

Support to configure the defaultroute (the destination IP address is0.0.0.0), and support to configurethe WAN connection to be the defaultroute

× × √ √ × × √

support to configure and check thedefault route for the telecomadminstrater level users

× × √ √ × × √

DHCP server × × √ √ × × √

Support DHCP Server，and support thedevice connected to the L3 Ethernetinterface can obtain the IP addressfrom the built-in DHCP server.

× × √ √ × × √

Support the primary DHCP server andthe secondary DHCP server

× × √ √ × × √

Support to enable/disable theprimary DHCP server

× × √ √ × × √

Support the default IP address ofthe primary DHCP Server is192.168.100.1, and the mask is255.255.255.0. And support toconfigure the IP address of theprimary DHCP Server manually.

× × √ √ × × √

Support the default start IP addressof the primary DHCP server's IPaddress pool is 192.168.100.2, thedefault ending IP address is192.168.100.254

× × √ √ × × √

第 34 页


V100R003C00&C01

Support the default lease term ofthe primary DHCP server is 72 hours,and support to configure the leaseterm manually in the unit of hour

× × √ √ × × √

Support to bind the IP address rangeof the primary DHCP server's IPaddress pool and the IP address ofthe primary DHCP Server, and supportto configure the start and ending IPaddresses of the primary DHCPserver's IP address pool manually inthe IP address range

× × √ √ × × √

Support to configue the IP addressfield of the primary DHCP serveraddress pool according to devicestypes including HGW、STB、Camera、Computer and Phone

× × √ √ × × √

The primary DHCP server supports toalocate relative IP addresses todifferent device types throughmatching with option 60 byte.

× × √ √ × × √

The secondary DHCP server supportsDHCP option 60.If the secondary DHCPserver is not configured with DHCPoption 60, this DHCP server isunavailable.

× × √ √ × × √

第 35 页


V100R003C00&C01

The secondary DHCP server supportsto be identified by DHCP option 60.Only the DHCP request with option 60can be allocated IP address from thesecondary DHCP server, and otherDHCP requests are allocated IPaddresses from the primary DHCPserver.

× × √ √ × × √

Support the default IP address ofthe secondary DHCP Server is192.168.2.1, and the mask is255.255.255.0. And support toconfigure the IP address of thesecondary DHCP Server manually.

× × √ √ × × √

Support to bind the IP address rangeof the secondary DHCP server's IPaddress pool and the IP address ofthe secondary DHCP Server, andsupport to configure the start andending IP addresses of the secondaryDHCP server's IP address poolmanually in the IP address range

× × √ √ × × √

support the DHCP server to checkwhether the collision exists betweenthe static/dynamic IP address in thenetwork and the IP address to beallocated

× × √ √ × × √

Portal × × √ √ × × √

第 36 页


V100R003C00&C01

In route moudle, it is supported toshift to relative portal URLaccording to devices types includingComputer、STB and Phone when acustomer access a network in thefirst time.

× × √ √ × × √

DHCP option × × √ √ × × √

When ONT is serving as the DHCPClient，it supports DHCP Option 50:Validation of the IP addressreceived in the DHCP Offer message.

× × √ √ × × √

When ONT is serving as the DHCPClient，it supports DHCP Option 15:Domain Name.

× × √ √ × × √

When ONT is serving as the DHCPClient，it supports DHCP Option 6:DNS Servers

× × √ √ × × √

When ONT is serving as the DHCPClient，it supports DHCP Option 42:NTP Server

× × √ √ × × √

When ONT is serving as the DHCPClient，it supports DHCP Option 60:Vender Class ID

× × √ √ × × √

When ONT is serving as the DHCPClient，it supports DHCP Option 120:SIP proxy (SBC)

× × √ √ × × √

support option121:route option whenworking as DHCP client

× × √ × × × √

DNS × × √ √ × × √

第 37 页


V100R003C00&C01

Support to obtain the IP address ofthe DNS server automatically whenthe WAN interface is configured toobtain the IP address through PPPoEor DHCP

× × √ √ × × √

Support to configure the IP addressof the DNS server manually when theWAN interface is configured with thestatic IP address

× × √ √ × × √

Support DNS Relay × × √ √ × × √Support DDNS × × √ √ × × √Support DNS Client × × √ √ × × √Support the primary and secondaryDNS Server addresses

× × √ √ × × √

support DDNS × × √ √ × × √

NAT/NAPT × × √ √ × × √

Support up to 1024 NAT/NAPT entries × × √ √ × × √Support NAPT function realized byhardware

× × √ √ × × √

support software NAPT function × × √ √ × × √

Virtual server × × √ √ × × √

Support the virtual server（alsocalled port mapping or portforwarding）. That is, support toenable the external server servicesof the private network.

× × √ √ × × √

Support up to 32 virtual servers × × √ √ × × √

第 38 页


V100R003C00&C01

Support to add the customizedvirtual server by the user.Themapping between the Internet portand the Intranet port is specifiedby the user.

× × √ √ × × √

Port trigger × × √ √ × × √

When the specified port in theIntranet transmits the packet, thespecified port in the Internet isenabled automatically and maps tothe corresponding port of the hostin the Intranet.

× × √ √ × × √

Support up to 32 Port triggers × × √ √ × × √Support to add the customized porttrigger by the userWhen the specified port in theIntranet transmits the packet, thespecified port in the Internet isenabled automatically and maps tothe corresponding port of the hostin the Intranet.

× × √ √ × × √

DMZ × × √ √ × × √

Support all the packets from the WANside which cannot be routed areredirected to the specified host inthe Intranet.

× × √ √ × × √

UPnP × × √ √ × × √

Support the UPnP deice is foundautomatically in the routing mode

× × √ √ × × √

Support to enable/disable UPnP × × √ √ × × √

ALG × × √ √ × × √

第 39 页


V100R003C00&C01

Support FTP ALG × × √ √ × × √Support TFTP ALG × × √ √ × × √Support SIP ALG × × √ √ × × √Support H.323 ALG × × √ √ × × √Support RTSP ALG × × √ √ × × √

3 Layer Multicast× × √ √ × × √

bridge type WAN interface supportsIGMP snooping

× × √ √ × × √

route type WAN interface supportsIGMP snooping

× × √ √ × × √

bridge type WAN interface supportsIGMP proxy

× × √ √ × × √

route type WAN interface supportsIGMP proxy

× × √ √ × × √

the 3 layer LAN interfaces bandedwith bridge-type WAN supportsmulticast service

× × √ √ × × √

the SSID banded with bridge-type WANsuppports multicust service

× × √ √ × × √

the 3 layer LAN interfaces bandedwith route-type WAN supportsmulticast service

× × √ √ × × √

the SSID banded with route-type WANsuppports multicust service

× × √ √ × × √

each bridge-type WAN interfacesupports a multicast VLAN

× × √ √ × × √

each route-type WAN interfacesupports a multicast VLAN

× × √ √ × × √

第 40 页


V100R003C00&C01

the 3 layer WAN banded with WANinterface supports the onlymulticast VLAN

× × √ √ × × √

WiFi only supports one multicastVLAN and one multicust group at most

× × √ √ × × √

Terminal AccessLimitation

× × √ √ × × √

supports to limit the number ofterminals connectting to the publicnetwork through WAN interface. Thelimitation scope is 0～253

× × √ √ × × √

Supports to the number of each typeterminals connecting to the publicnetwork through WAN interface. Thedevices type includes STB、Camera、Computer and Phone the limitationscope is 0～253 for each terminaltype

× × √ √ × × √

Support to enable/disable the LANside access through FTP,TELNET andHTTP

√ √ √ √ √ √ √

Support to enable/disable the WANside access through FTP,TELNET andHTTP

√ √ √ √ √ √ √

Voice Feature × √ √ √ × √ √

POTS interfacefeature

√ √ √ √ × √ √

第 41 页


V100R003C00&C01

Support to adjust the gain of POTSinterface，and the adjustment rangeof input gain is -6db～+5db，theadjustment range of output gain is -12db～0db.

√ √ √ √ × √ √

upport to configure upper and lowerthreshold of hookflash，and theconfiguration range is 0ms～1400ms

√ √ √ √ × √ √

Support to configure parameters ofPOTS interface

√ √ √ √ × √ √

Support to configure the DSPparameter template for POTSinterface

√ √ √ √ × √ √

Support 19 pre-configured ringingmodes and 16 custom ringging modes

√ √ √ √ × √ √

REN：Allows a port to connect to amaximum of four telephones

√ √ √ √ × √ √

Support the pulse-based digitcollection at the speed of 8 pps to12 pps. The break-make ratio is inthe range of 50% and 80%. Theinterval of pulses is configurableand is in the range of 100 ms and2550ms. The default interval ofpulses is 240 ms.

√ √ √ √ × √ √

Support DTMF digit collection √ √ √ √ × √ √Support to input SN through dialing √ √ √ √ × √ √Support to input password throughdialing

√ √ √ √ × √ √

第 42 页


V100R003C00&C01

Voiceencoding/decoding

√ √ √ √ × √ √

Support G.711a/u, G.729a/b and G.722encoding and decoding

√ √ √ √ × √ √

Support voice activitydetection(VAD) and comfort noisegeneration(CNG)

√ √ √ √ × √ √

Support packet losscompensation(PLC)

√ √ √ √ × √ √

Support adaptive jitter buffer (AJB)and static jitter buffer

√ √ √ √ × √ √

Support the adaptive range ofadaptive jitter buffer is 0～200ms

√ √ √ √ × √ √

Support the configuration range ofstatic jitter buffer is 0～200ms

√ √ √ √ × √ √

Support the FAX and MODEM servicesto use static jitter bufferfixedly，and the voice service to beconfigured to use adaptive jitterbuffer or static jitter buffer

√ √ √ √ × √ √

Support the local echo cancellation,and comply with G.165 and G.168,

√ √ √ √ × √ √

Support DTMF dialing detection,pulse dialing detection and firstdial only configuration

√ √ √ √ × √ √

Support the DTMF dialing during acall to be received and transmitedthrough the RFC 2833

√ √ √ √ × √ √

第 43 页


V100R003C00&C01

Support the fax events to bereceived and transmited through theRFC 2833

√ √ √ √ × √ √

Support the redundancy of RTP incompliance with RFC 2198，which isenabled in fax and modem services

√ √ √ √ × √ √

Support the redundancy of 2833 incompliance with RFC 2198，which isenabled in voice service

√ √ √ √ × √ √

Support to carry VoIP by RTP/RTCPprotocol defined in RFC 3550

√ √ √ √ × √ √

Support session descriptionprotocol(SDP) defined in RFC2327/RFC 3407

√ √ √ √ × √ √

Supports to receive and send RTCP XRmessages based on RFC3611

√ √ √ √ × √ √

support to configure the lockcurrent of POTS interfaces

√ √ √ √ × √ √

support to configure the gain ofPOTS interface

√ √ √ √ × √ √

support RFC 2833 hookflash sending √ √ √ √ × √ √

voice services √ √ √ √ × √ √

Support the basic call initiatedfrom the caller or callee

√ √ √ √ × √ √

Support two simultaneous voice calls √ √ √ √ × √ √

Support the calling lineidentification presentation(CLIP)through FSK，including MDMF formatand SDMF format

√ √ √ √ × √ √

第 44 页


V100R003C00&C01

Support the calling lineidentification presentation(CLIP)through DTMF

√ √ √ √ × √ √

Support the calling lineidentification presentation when thecaller goes on-hook

√ √ √ √ × √ √

Support the calling lineidentification presentation during acall

√ √ √ √ × √ √

Support the calling timepresentation

√ √ √ √ × √ √

Support the calling lineidentification restriction(CLIR)

√ √ √ √ × √ √

Support the calling lineidentification restriction override

√ √ √ √ × √ √

Support the message waitingindicator(MWI)

√ √ √ √ × √ √

Support the call waiting √ √ √ √ × √ √Support the call hold √ √ √ √ × √ √Support the call transfer √ √ √ √ × √ √Support the call forwardingunconditional, call forwarding onbusy, and call forwarding on noreply

√ √ √ √ × √ √

Support the conference call √ √ √ √ × √ √Support the three-party service √ √ √ √ × √ √Support the calling party and calledparty services

√ √ √ √ × √ √

Support the Centrex service √ √ √ √ × √ √Support the malicious callidentification

√ √ √ √ × √ √

第 45 页


V100R003C00&C01

Support hotline √ √ √ √ × √ √Support the polarity reversalbilling

√ √ √ √ × √ √

Support the polarity-reversing pulsebilling

√ √ √ √ × √ √

Support the subscriber pulsemetering(SPM) 12 kHz/16 kHz

√ √ √ √ × √ √

Support the advice of charge at theend of conversation

√ √ √ √ × √ √

support configurate ClipFskMode、ClipTasPattern and ClipForceSendFskon POTS interfaces

√ √ √ √ × √ √

support voice log √ √ √ √ × √ √

Support SIP √ √ √ √ × √ √

Comply with IETF RFC 3261 √ √ √ √ × √ √Support the register flow of SIP √ √ √ √ × √ √Support the registration DIGESTauthentification flow

√ √ √ √ × √ √

Support the call DIGESTauthentification flow

√ √ √ √ × √ √

Support UA-Profile subscription flow√ √ √ √ × √ √

Support MWI subscription flow √ √ √ √ × √ √Support REG-STATE subscription flow √ √ √ √ × √ √Support registration avalancheprevention

√ √ √ √ × √ √

Support dual homing using OPTIONsignaling to detect the status ofprimary and secondary server

√ √ √ √ × √ √

第 46 页


V100R003C00&C01

Support dual homing using REGISTERsignaling to detect the status ofprimary and secondary server

√ √ √ √ × √ √

Support Early Media √ √ √ √ × √ √Support OPTION heartbeat mechanism √ √ √ √ × √ √Support acknowledgement ability fortemporary responding meassage

√ √ √ √ × √ √

Requirement for initial INVITEmessage, 100 rel is the requiredparameter by default，and SDP isrequired

√ √ √ √ × √ √

Support media negotiation mechanism √ √ √ √ × √ √Support Session Timers mechanismdescribed by RFC4028

√ √ √ √ × √ √

Support DNS resolution for Porxyaddress

√ √ √ √ × √ √

Support to transmit RTCP statisticsof QoS in BYE message or 200/BYEmessage

√ √ √ √ × √ √

Support to receive the OPTION returninband and outband，and supportreturn 486 when endpoint is busy

√ √ √ √ × √ √

Support to include the attributecapability parameters of terminal incompliance with RFC 3840 whenregistering

√ √ √ √ × √ √

Support to include the callpreference capablity in compliancewith RFC 3841 when sending INVITEmessage

√ √ √ √ × √ √

第 47 页


V100R003C00&C01

Support to fetch time from the DATEhead field of SIP message when CLIPservice is displaying

√ √ √ √ × √ √

Support the MCID service processingof MESSAGE sending mode

√ √ √ √ × √ √

Support green call √ √ √ √ × √ √Support multiple standardnegotiation modes for fax and Modem

√ √ √ √ × √ √

Support to configure the audioencoding/decoding list and priority

√ √ √ √ × √ √

Support to configure multiple SIPaccounts for each POTS interface，and support up to 17 SIP accounts

√ √ √ √ × √ √

Support to map SIP Status Code tosignal tone，that is support todisplay designation signal toneaccording to the received respondingcodes of INVITE message

√ √ √ √ × √ √

Support OPTION 120 processing √ √ √ √ × √ √Support to play tone remotely，thatis support to play ringback tone andcall holding tone remotely throughconfiguration

√ √ √ √ × √ √

Support to provide defferent ringmode according to the SIP message

√ √ √ √ × √ √

第 48 页


V100R003C00&C01

Support to configure some newservices on ONT from BMS/ACSThe new services can be configuredby user includes call waiting, callforwarding，call transfer，themessage waiting indicator(MWI) andhotline.Those functions are supported sinceV100R003 version: call hold,3-party,conference call,CLIR，centrixprefix and property, displaynameenable and content,MCID

√ √ √ √ × √ √

Support the TISPAN tight couplingbasic call when integrates with BT'scall server

√ √ √ √ × √ √

Support the TISPAN tight couplingsupplementary call when integrateswith BT's call server

√ √ √ √ × √ √

Support to configure and realizeuser's priority

√ √ √ √ × √ √

Support to configure digital map √ √ √ √ × √ √

support ND1033 register re-trial andmaster/stand-by proxy switch processof British Telecom(BT)

√ √ √ √ × √ √

H.248 Protocol √ √ √ √ × √ √

Support H.248.1 V1/V2/V3 and versionnegotiation

√ √ √ √ × √ √

Support H.248 over UDP √ √ √ √ × √ √

第 49 页


V100R003C00&C01

Support the H.248 messages to usethe Long/Short format for encodingand decoding

√ √ √ √ × √ √

Support the encoding/decodingnegotiation between the local endand the remote end

√ √ √ √ × √ √

Support H.248 avalanche prevention，and the avalanche prevention timefor the ONT interface can beconfigured.

√ √ √ √ × √ √

Support to match the wildcard username delivered by the softswitch,and then resolve all the userinterfaces that do not match thewildcard

√ √ √ √ × √ √

Support control parameters for H.248profiles, which facilitatesinterconnection with softswitches indifferent markets

√ √ √ √ × √ √

Support to pre-configure a globaldigitmap (with the maximum length of8000 characters) that need not bedelivered in the signaling throughthe softswitch

√ √ √ √ × √ √

Support to configure digital map √ √ √ √ × √ √

Support dual-homing, and comply withthe flows of ITU-T H.248.1 Annex F

√ √ √ √ × √ √

Support the heartbeat message andflow defined by H.248.14

√ √ √ √ × √ √

第 50 页


V100R003C00&C01

Support to use the IP address,domain name, device name as the MID

√ √ √ √ × √ √

Support to transmit the notifymessage on the same point in theserial mode

√ √ √ √ × √ √

Support to hold the call ordisconnect the call in case ofinterface abnormality

√ √ √ √ × √ √

Support to shut down the interfacein the graceful mode

√ √ √ √ × √ √

Support the cold start, warm start,general reset to reset the interface

√ √ √ √ × √ √

Support the authentication for H.248messages, including the AHauthentication and the DHauthentication.

√ √ √ √ × √ √

Support to pre-configure the off-hook events for different packetsbased on different softswitches.

√ √ √ √ × √ √

Support multiple digitmap matchingmodes such as the longest-matchmode, shortest-match mode, and re-match mode after error dialing, andsupport multiple error-processingmodes such as error number report,delay report, and discarding

√ √ √ √ × √ √

Support to display signals insequence or at intervals accordingto the signal list

√ √ √ √ × √ √

第 51 页


V100R003C00&C01

Support the buffer event and processthe buffer event according to theH.248 event-processing rule

√ √ √ √ × √ √

Support to transmit and respond theH.248 packet in fragment, andconfigure the maximum length of thepacket that can be transmittedaccording to the configured MDUparameter

√ √ √ √ × √ √

Support the general and optionalcommands

√ √ √ √ × √ √

Support resources reservation，including resources groupreservation and resources valuereservation

√ √ √ √ × √ √

Support to transmit the DTMF signaltone in the outband mode

√ √ √ √ × √ √

Support RFC 2833 encryption √ √ √ √ × √ √

Fax/Modem √ √ √ √ × √ √

Support the fax signal detection，including CNG/V21/ANS/ANSBAR

√ √ √ √ × √ √

第 52 页


V100R003C00&C01

Support the Modem signal detection，including V.8bis/V.22/V.22bis/V.23/V.25/V.32/V.32 bis/V.32ext/V.34/V.90/V.92/V.27ter/V.29/V.17/V.18support the open/close of checkingthe Bahrein Modem single tone in theway of ANSbar based on POTSinterface, single tone frequencyincluding 1300Hz,1650Hz and 980Hzsupport the open/close of checkingthe BELL ANS singal in the way ofANSbar based on POTS interface,single tone frequency including2225Hz and 2250Hz

√ √ √ √ × √ √

Support the T.38 fax，includingautomatic switching T.38 fax andnegotiation T.38 fax

√ √ √ √ × √ √

Support to switch to voice afterT.38 fax

√ √ √ √ × √ √

Support the G.711 fax，includingautomatic switching G.711 fax andnegotiation G.711 fax

√ √ √ √ × √ √

Support the modem transparenttransmission，including automaticswitching Modem transparenttransmission and negotiation Modemtransparent transmission

√ √ √ √ × √ √

Signal tone √ √ √ √ × √ √

第 53 页


V100R003C00&C01

Support signal tone complied withChinese standards

√ √ √ √ × √ √

Support signal tone complied withRussia standards

√ √ √ √ × √ √

Support signal tone complied withCroatia standards

√ √ √ √ × √ √

Support signal tone complied withGermany standards

√ √ √ √ × √ √

Support signal tone complied withHungary standards

√ √ √ √ × √ √

Support signal tone complied withSlovakia standards

√ √ √ √ × √ √

Support signal tone complied withItaly standards

√ √ √ √ × √ √

Support signal tone complied withUnited Arab Emirates's standards

√ √ √ √ × √ √

Support signal tone complied withSpanish standards

√ √ √ √ × √ √

Support signal tone complied withArgentina standards

√ √ √ √ × √ √

Support signal tone complied withBrazil standards

√ √ √ √ × √ √

Support signal tone complied withMacedonia standards

√ √ √ √ × √ √

Support to configure and providecustomized signal tone

√ √ √ √ × √ √

Support to configure country code，and support to configurecorresponding signal tone parametersaccording to the country code

√ √ √ √ × √ √

第 54 页


V100R003C00&C01

Voice performance√ √ √ √ × √ √

G.711 voice performance：packetization in 20msGood network environment，MOS>4.0,PESQ>4.0；Poor network environment（packetloss ratio=1%，network jitter=20ms，delay=150ms），MOS>3.7,PESQ>3.8；Adverse network environment（packetloss ratio=5%，network jitter=60ms，delay=400ms），MOS>3.3,PESQ>3.3

√ √ √ √ × √ √

G.729 voice performance：packetization in 20msGood network environment，MOS>3.8,PESQ>3.7；Poor network environment（packetloss ratio=1%，network jitter=20ms，delay=150ms），MOS>3.3,PESQ>3.3；Adverse network environment（packetloss ratio=5%，network jitter=60ms，delay=400ms），MOS>2.8,PESQ>2.8

√ √ √ √ × √ √

第 55 页


V100R003C00&C01

G.722 voice performance：packetization in 20msGood network environment，MOS>4,PESQ>4；Poor network environment（packetloss ratio=1%，network jitter=20ms，delay=150ms），MOS>3.7,PESQ>3.6；Adverse network environment（packetloss ratio=5%，network jitter=60ms，delay=400ms），MOS>3.3,PESQ>3

√ √ √ √ × √ √

End to end processing delay ofencoding and decoding：G.711(10ms):≤28msG.711(20ms):≤48msG.729(10ms):≤32msG.729(20ms):≤60ms

√ √ √ √ × √ √

Dial tone delay <300ms √ √ √ √ × √ √Delay after dialing <600ms √ √ √ √ × √ √Delay after called off-hook <200ms √ √ √ √ × √ √Support up to 48 hours communicationwithout interruption

√ √ √ √ × √ √

Support the call loss ≤4％％ andthe call attempts per second(CAPS)≥ 0.1 attempt/s

√ √ √ √ × √ √

第 56 页


V100R003C00&C01

T.38 fax performance：The dialup success ratio is 95% inthe condition that the packet lossratio is 5%, delay is 200 ms, andnetwork jitter is 20 ms.(notconsider call loss).

√ √ √ √ × √ √

G.711 fax performance：The dialup success ratio is 95% inthe condition that the delay is 200ms, network jitter is 20 ms, andwithout packet loss ratio.

√ √ √ √ × √ √

Modem transparent transmissionperformance：The dialup success ratio is 95% withover-one hour online in thecondition that the delay is 100 ms,network jitter is 20 ms, and withoutpacket loss ratio.

√ √ √ √ × √ √

Support to transmit RTCP statisticsper 1s at least,and the defaultinterval is 5s

√ √ √ √ × √ √

Voice reliabilityand QoS

√ √ √ √ × √ √

Support H.248 dual homing √ √ √ √ × √ √Support SIP dual homing √ √ √ √ × √ √Support 2 virtual accessgateway(VAG), and each POTS canvertulized a VAG and different VAGaccess different softswitch.

√ √ √ √ × √ √

第 57 页


V100R003C00&C01

Support to configure the 802.1Ppriority of local media IP addressand signaling IP address

√ √ √ √ × √ √

Support to configure the DSCP valueof local media IP address andsignaling IP address

√ √ √ √ × √ √

O&M Feature √ √ √ √ √ √ √

Eth OAM √ √ √ √ √ √ √

Complys with IEEE 802.1agprotocol/CFM（Connectivity FaultManagement）

√ √ √ √ √ √ √

Support to build MD(maintenancedomains),MA(maintenanceassociations),MEP(maintenance endpoint) in ONT

√ √ √ √ √ √ √

ONT MEP supports CC(continuitycheck) function

√ √ √ √ √ √ √

Support to keep alarm status andrecord log for the errors checkedby CC

√ √ √ √ √ √ √

ONT MEP supports LB(Loopback)function

√ √ √ √ √ √ √

ONT MEP supports LT(Linktrace)function

√ √ √ √ √ √ √

Support the transparent transmissionof CFM high-level message inupstream and downstream;The VLAN tag translation rules isthe same with common packets.

√ √ √ √ √ √ √

第 58 页


V100R003C00&C01

Support serviceconfiguration andmaintenancethrough TR069

× × √ √ × × √

Comply with TR069,TR098 and TR104 × × √ √ × × √Support http/soap protocol × × √ √ × × √Support TR069 connections initiatedby the CPE

× × √ √ × × √

Support TR069 connections initiatedby the ACS

× × √ √ × × √

Support basic bidirectional andbrief bidirectional authentication

× × √ √ × × √

Support the TR-069 standard RPCmethods.

× × √ √ × × √

Support ACS discovery usingOMCI/OAM.

× × √ √ × × √

Support to configure and inquireWLAN service

× × √ √ × × √

Support to configure and inquire WANinterface

× × √ √ × × √

Support to configure and inquire LANinterface with L3 mode

× × √ √ × × √

Support to configure and inquireabout routing features

× × √ √ × × √

Support performance statistics anddiagnosis of L2/L3 service

× × √ √ × × √

Support to configure and inquire USBinterface

× × √ √ × × √

第 59 页


V100R003C00&C01

Support to configure and inquire SIPservice

× × √ √ × × √

Support to configure and inquireH.248 service

× × √ √ × × √

Support to process emulation callthrough TR069

× × √ √ × × √

Support to catch packet of mediastream remotely through TR069

× × √ √ × × √

Support to inquire the physicalstatus of POTS interface throughTR069

× × √ √ × × √

Support to inquire user's callstatus and register status throughTR069

× × √ √ × × √

Support to make SIP users in serviceor out of service through TR069

× × √ √ × × √

Support to process loop line testthrough TR069

× × √ √ × × √

Support to process loopback testthrough TR069,including the localand remote loopback of POTSinterface,the local and remoteloopback of RTP

× × √ √ × × √

Support PING diagnotics throughTR069

× × √ √ × × √

Support to test and print TR069messages

× × √ √ × × √

第 60 页


V100R003C00&C01

Support toconfigure andinquire throughWeb browser

√ √ √ √ √ √ √

Support Web browser in English √ √ √ √ √ √ √Support the default primary IPaddress of Web is 192.168.100.1，mask is 255.255.255.0

√ √ √ √ √ √ √

Support hierarchical management ofweb，and support telecomadministrator account and generalaccount;

√ √ √ √ √ √ √

If the customer fails to fillusername and password inconsecutive 3 times, the WEB will belocked for 1 minute.

√ √ √ √ √ √ √

If there is no any process, WEB willbe logout automatically

√ √ √ √ √ √ √

Support to input or modify passwordthrough Web for ONT registration

√ √ √ √ √ √ √

Support to modify SN through Web √ √ √ √ √ √ √

Support to reset the ONT through Web√ √ √ √ √ √ √

Support to restore the defaultconfiguration through Web

√ √ √ √ √ √ √

第 61 页


V100R003C00&C01

Support to query the deviceinformation through Web, includingVendor ID, EquipmentID, softwareversion, Issued date, hardwareversion and SN, ONT registrationstate and ONT ID

√ √ √ √ √ √ √

Support to query the batteryavailable capacity through Web

√ √ √ √ × √ √

Support to query optic status(sendlight normally/initiatively sendlight always/shut down transmitterpower),sending optic power,receiving optic power,workingvoltage and working temperaturethrough Web.

√ √ √ √ √ √ √

Support to query the status of WANinterface through Web

√ × √ √ × × √

Support to query the status ofEthernet interface through Web

√ √ √ √ √ √ √

Support to query the allocated IPaddress information of primary andsecondary DHCP servers through Web，including MAC address, IP addressand lease time remaining,

√ × √ √ × × √

Support to configure and query thestatic ARP table through Web

√ × √ √ × × √

Support to configure and query NTPserver,time zone and daylight savingtime

√ × √ √ × × √

第 62 页


V100R003C00&C01

Support to configure IP, port numberand authentification key of Radiusserver

√ × √ √ × × √

Support to configure each Ethernetinterface to work in L2 or L3 modethrough Web

√ × √ √ × × √

Support to configure the IP address,the IP address range and lease timeof primary and secondary DHCPServers through Web

√ × √ √ × × √

Support to configure WAN interfacethrough Web，includingenable/disable WAN interface,WANservice types, VLAN, priority,enable/disable NAT, obtaining modeof IP address,binding Ethernetinterfaces and SSID, static IPaddress, subnet mask, gatewayaddress，static primary andsecondary DNS addresses，PPPoEusername and password

√ × √ √ × × √

Support to configure and query PortMapping through Web

√ √ √ √ √ √ √

Support to configure and query PortTrigger through Web

√ × √ √ × × √

Support to configure and query ALGthrough Web

√ × √ √ × × √

Support to configure and query DMZthrough Web

√ × √ √ × × √

Support to configure and querydefault routing through Web

√ × √ √ × × √

第 63 页


V100R003C00&C01

Support to configure and querystatic routing through Web

√ × √ √ × × √

Support to enable/disable the LANside access through FTP,TELNET andHTTP through Web

√ × √ √ × × √

Support to enable/disable the WANside access through FTP,TELNET andHTTP through Web

√ × √ √ × × √

Support PING through Web √ × √ √ √ × √Support to enable/disable UPNPthrough Web

√ × √ √ × × √

Support to enable/disable WLANthrough Web

× × √ √ × × √

Support to configure the countrycode of WLAN

× × √ √ × × √

Support to configure transmittingpower of WLAN, which is in form ofpercentage, 100% is corresponding to100mW

× × √ √ × × √

Support to configure the channelselection mode through web,including the automatic channelselection and manual configurationfor the channel

× × √ √ × × √

Support to configure multiple SSIDsthrough web, and each SSID consistsof up to 32 characters. And supportto enable/disable SSID broadcasthiding. Support to configure thenumber of associated devices.Support to enable/disable WMM.

× × √ √ × × √

第 64 页


V100R003C00&C01

Support to configureauthentification mode ofWLAN(including Open System,SharedKey,WPA-PSK,WPA2-PSK,WPA,WPA2,WPS)through web. Support to configureencryption arithmetic(includingAES,TKIP,AES+TKIP).

× × √ √ × × √

Support to configure renewing timeof WLAN key through web

× × √ √ × × √

Support to configure WPS mode(pushbutton/pin) of WLAN through web

× × √ √ × × √

Support to configure to downloadfile from ftp server to the USB massstorage device through web

× × √ √ × × √

Support to configure URL of ACSthrough web

× × √ √ × × √

Support to configure the usernameand password of ACS，and theusername and password of CPE throughweb

× × √ √ × × √

Support to enable/disable periodinform of ACS and configure theperiod inform interval through web

× × √ √ × × √

Support to change the password ofgeneral account through Web

√ √ √ √ √ √ √

Support to upload the configurationfile through web，after successfuluploading, ONT will restart.

√ √ √ √ √ √ √

Support to backup the currentconfiguration file through web

√ √ √ √ √ √ √

第 65 页


V100R003C00&C01

Support to enable/disable logthrough Web

√ √ √ √ √ √ √

Support to display log through Web √ √ √ √ √ √ √Support to configure and querycountry code and digital map matchmode

√ √ √ √ × √ √

Support to configure and query SIPinterface

√ √ √ √ × √ √

Support to configure and query SIPuser

√ √ √ √ × √ √

Support to query the user status andcall status of SIP through web

√ √ √ √ × √ √

Support to configure and query H.248interface

√ √ √ √ × √ √

Support to configure and query H.248user

√ √ √ √ × √ √

Support to query the user status andcall status of H.248 through web

√ √ √ √ × √ √

Support to restart VoIP servicethrough web

√ √ √ √ × √ √

Support query the statistic ofreceived and sent packets ofEthernet ports through WEB

√ √ √ √ √ √ √

Support to query the devices typeinformation of thoes devices whichIP addresses have been allocatedfrom primary and standby DHCP serveraddress pool through WEB

√ × √ √ × × √

第 66 页


V100R003C00&C01

support to configure and query theIP field of the primary DHCP serveraddress pool through WEB

√ × √ √ × × √

Support to configue to open/closeWAN multicast through WEB and afterWAN multicast opening, it issupported to configue IGMP snooping.

√ × √ √ × × √

Support to configue to open/closeWAN multicast through WEB and afterWAN multicast opening, it issupported to configue IGMP proxy.

√ × √ √ × × √

support to configue and query DDNSthrough WEB

√ × √ √ × × √

support to configue and query portalthrough WEB

√ × √ √ × × √

Support to configure and limit thetotal number of terminal or everykind of terminals accessed to thepublic network through WEB

√ × √ √ × × √

Support to configue URL filteringthrough web

√ × √ √ × × √

Support to configue FTP Serverthrough WEB

√ × √ √ × × √

Suppor to configue SSL digitalcertificate of TR069 through web

√ × √ √ × × √

Support to configue fileloading/backuping through USB on theWEB

√ × √ √ × × √

第 67 页


V100R003C00&C01

Suppor to configue to open/close logand the log filtering levelincludes:Emergency、Alert、Critical、Error、Warning、Notice、Informational、Debug

√ √ √ √ √ √ √

Support to show log informationthrough web

√ √ √ √ √ √ √

Support to download and save loginformation through web

√ √ √ √ √ √ √

ONT's ServiceConfigure Mode

√ √ √ √ √ √ √

The service configuration andmaintenance of ONT is completed fromBMS:The PON line parameters and L2service are configured through OMCI;The VoIP and L3 service areconfigured through XML files.The WLAN and USB service areconfigured through WEB browser.

√ √ √ √ √ √ √

The service configuration andmaintenance of ONT is completed fromBMS and TMS.1.The PON line parameters and L2service are configured through SNMPplus OMCI;2.The VoIP and L3 service areconfigured from TMS.3.The WLAN, USB service can beconfigured from TMS/WEB.

× × √ √ × × √

第 68 页


V100R003C00&C01

Software update√ √ √ √ √ √ √

Support the upgrade through Web √ √ √ √ √ √ √Support the remote upgrade throughOMCI

√ √ √ √ √ √ √

Support the batch automaticalupgrade from the NMS

√ √ √ √ √ √ √

Support the remote upgrade throughTR069

√ √ √ √ √ √ √

Support not to interrupt the serviceduring the upgrade process

√ √ √ √ √ √ √

Support dual protective system:normal system and small system

√ √ √ √ √ √ √

Support to start up from normalsystem firstly, start up from smallsystem only when normal systemfailed.

√ √ √ √ √ √ √

Small system support to reloadsoftware program into normal systemfrom BMS/TMS.

√ √ √ √ √ √ √

Support configuration file rollback √ √ √ √ √ √ √

Diagnosis √ √ √ √ √ √ √

Support the loopback test of theEthernet interface

√ √ √ √ √ √ √

Support the loopback test of GEMport

√ √ √ √ √ √ √

Support the emulation call，supportPOTS interface to emulate caller andcallee，and support two POTSinterfaces to emulate concurrently

√ √ √ √ × √ √

第 69 页


V100R003C00&C01

Support the loop line test of POTSinterface

√ √ √ √ × √ √

Support to catch packet of mediastream remotely，and support twoPOTS interfaces to catch packetconcurrently

√ √ √ √ × √ √

Support to check the association ofkey VoIP data configured through Weband TR069

× × √ √ × × √

Support PPPoE emulation √ √ √ √ √ √ √

ICMP √ √ √ √ √ √ √

Support ping function √ √ √ √ √ √ √

SNTP √ √ √ √ √ √ √

Support SNTP Client protocol √ √ √ √ √ √ √Support to configure SNTP Server，support up to 2 SNTP Servers

√ √ √ √ √ √ √

EnergyConservationFeature

√ √ √ √ √ √ √

Normal workingmode

√ √ √ √ √ √ √

In default, ONT works in normal modewithout energy conservation.

√ √ √ √ √ √ √

System energy-conservation mode

√ √ √ √ √ √ √

Supports enabling/disabling of thesystem energy-conservation mode byconfiguration.

√ √ √ √ √ √ √

第 70 页


V100R003C00&C01

In this mode, when not running anyservice, the ONT automatically setsits idle service components to thehibernating state to reduce powerconsumption. When required to runthe service again, the ONTautomatically wakes up thehibernating components from theenergy-conservation mode to resumethe corresponding serviceprovisioning.

√ √ √ √ √ √ √

Battery backupMode

√ √ √ √ × √ √

Support to enter battery backup modeautomatically when battery providethe power to system

√ √ √ √ × √ √

Support to configure the policies inbattery backup mode(that is to say,configure which service is poweredby battery.)

√ √ √ √ × √ √

When the energy-conservation mode isenabled, ONT supports the systemenergy-conservation feature for theservice which is enabled in batterybackup mode.

√ √ √ √ × √ √

第 71 页


V100R003C00&C01

Support to configure backup poweralarm strategy, including:1,always open alarm function2,only if the VoIP works,the alarmfunction is open3,always close alarm function

√ √ √ × √ √ √

support to close/open the backuppower alarm function when the VoIPis Not ok/OK

√ √ √ × √ √ √

EngineeringFeature

√ √ √ √ √ √ √

Workingenvironment

√ √ √ √ √ √ √

Indoor productAmbient temperature:0°C to 40°CRelative humidity: 5% RH to 95% RH

√ √ √ √ √ √ √

Heat dissipation√ √ √ √ √ √ √

No fan design, and heat isdissipated naturally

√ √ √ √ √ √ √

EMC requirement√ √ √ √ √ √ √

1. Comply with EN550221998+A1:2001+A2:2003, EN550241998+A1:2001+A2:2003, EN61000-3-2:2001, EN61000-3-3:2001, andGB9254:19982. Support shielding performance: 30-230 MHz: 30 dB 230-1000 MHz: 20dB

√ √ √ √ √ √ √

第 72 页


V100R003C00&C01

Safetyrequirement

√ √ √ √ √ √ √

Comply with IEC60950-1, EN60950-1,IEC60825-1/2, and GB4943

√ √ √ √ √ √ √

Productcertification

√ √ √ √ √ √ √

Support CE certifications,supportWiFi alliance certification

√ √ √ √ √ √ √

Environment-friendlyrequirement

√ √ √ √ √ √ √

Comply with China RoHS6（20 years）and Europe RoHS

√ √ √ √ √ √ √

Plain packagingadopted

√ √ √ √ √ √ √

Plain packaging adopted √ √ √ √ √ √ √

Packagingmaterials thatare environment-friendly

√ √ √ √ √ √ √

The package carton is environment-friendly and can protect the devicefrom damages during the delivery,loading/unloading, and storingprocess.

√ √ √ √ √ √ √

Device tag √ √ √ √ √ √ √

第 73 页


V100R003C00&C01

According to the device tagregulations, identify and protectthe safety tag, LED tag, interfacetag, ex-factory tag, and devicemodel tag

√ √ √ √ √ √ √

Obviously identifies the MAC and SNon the device

√ √ √ √ √ √ √

第 74 页

Product Photo HG8240 GPON for BT is white

User network interface 1GE 1GE+1POTS 2POTS+4GE 2POTS+4GE+USB+WIFI 2POTS+4GE+USB+RF+WIFI 4POTS+4GE+USB+WiFi+RF 4GE+2POTS+RFOptical interface SC/APC(general)；LC/APC(DT) SC/APC SC/APC SC/APC SC/APC SC/APC SC/APCDimension 143mm×115mm×30mm 143mm×115mm×30mm 195mm×155mm×34mm 195mm×174m×34mm 268mm×213mm×34mm 268mm×213mm×34mm 268.5×213.5×34.5mm

weight about 450g about 450g about 500g about 550g about 800g about 800g about 750gThe weight of power adapter isincluded.

Support power adapter output forthe ONT board：11-14V DC，1A；

Support power adapter outputfor the ONT board：11-14V DC，1A；

Support power adapteroutput for the ONT board：11-14V DC，1A；

Support power adapteroutput for the ONTboard：11-14V DC，2A；

Support power adapteroutput for the ONTboard：11-14V DC，2A；



Support power adapter input:100V～240V AC，50Hz～60Hz

Support power adapterinput:100V～240V AC，50Hz～60Hz






MTBF of ONT 36.1 years 34years 24.4years 23.5years 22.5years 22.5years 25 yearsMTBF of Power Adapter 60000hours 60000hours 60000hours 60000hours 60000hours 60000hours 60000hoursIndoor Product Ambient Temperature:0℃～+40℃ 0℃～+40℃ 0℃～+40℃ 0℃～+40℃ 0℃～+40℃ 0℃～+40℃ 0℃～+40℃Relative Humidity 5%～95% 5%～95% 5%～95% 5%～95% 5%～95% 5%～95% 5%～95%

Power

Static Power：4wAverage Power：5wMaximum Power：6w

Static Power：5wAverage Power：6wMaximum Power：7w

Static Power：6wAverage Power：7.5wMaximum Power：12w

Static Power：6.5w

Average Power：8w

Maximum Power：17w

Static Power：6.5w

Average Power：11w

Maximum Power：16w

Static Power：6.5w

Average Power：11w

Maximum Power：18w

Static Power：5wAverage Power：10.5wMaximum Power：14w

The configuration of averagepower：HG8010: 1 FE interfacessends/receives dataHG8110: 1GE interfacessends/receives dataHG8240：2 GE interfacessends/receives dataHG8245：2 GE and WiFi interfacesends/receives dataHG8247：2 GE and WiFi interfacesends/receives data and RF isenabled.HG8447：2 GE and WiFi interfacesends/receives data and RF isenabled.HG8242： 2GE+RF interfacessends/receives data

Power adapter CertificationCCC、CE Certification CCC、CE Certification CCC、CE Certification CCC、CE Certification CCC、CE Certification CE Certification CCC、CE Certification

The AC plug type of PowerAdapter

SupportChinese/Europe/British/Americantwo core

SupportChinese/Europe/British/Americantwo core

SupportChinese/Europe/British/American two core

SupportChinese/Europe/British/American three core

SupportChinese/Europe/British/American three core

SupportChinese/Europe/British/American two core

Support Chinese/Europe/British

Backup batteryNONE 2Ah/4Ah lithium battery with

battery monitoring function

2Ah/4Ah lithium batterywith battery monitoringfunction



2Ah/4Ah lithium battery withbattery monitoring function

2Ah/4Ah lithium battery withbattery monitoring function

Power Adapter

HG8010 HG8110 HG8447HG8245 HG8247 HG8242 RemarkSpecifications HG8240

第 75 页

Date post:	31-Jan-2018
Category:	Documents
Upload:	truongdan
View:	309 times
Download:	20 times

Huawei EchoLife ONT V100R003C00&C01 Function List(28-Sep-2011) · PDF fileHuawei EchoLife ONT...

Documents