Ilumipod Inground Tri-3 IP Optic WW User Manual … · 2016-04-18 · company names, trademarks...

Ilumipod Inground Tri-3 IP Optic 25 WW

User Manual

Edition Notes

Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7

Edition Notes The Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7 covers the description, safety precautions, installation, programming, operation, and maintenance of the Ilumipod Inground Tri-3 IP Optic 25 WW. ILUMINARC® released this edition of the Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7 in March 2016.

Trademarks The ILUMINARC® logo, the ILUMINARC® name and all other trademarks in this document related to services or products by ILUMINARC® are trademarks owned or licensed by ILUMINARC®, its affiliates or subsidiaries. Any other product names, logos, brands, company names, trademarks featured or referred to within this document are the property of their respective trademark holders.

Copyright Notice The entire content of this document, except where applicable and unless otherwise noted, is solely owned by ILUMINARC®, a wholly owned trademark of Chauvet & Sons, LLC. © Copyright 2016 ILUMINARC®. All rights reserved. Electronically published by ILUMINARC® in the United States of America.

Manual Usage ILUMINARC® authorizes its customers to download and print this manual for professional information purposes only. ILUMINARC® expressly prohibits the usage, copy, storage, distribution, modification, or printing of this manual or its content for any other purpose without its written consent.

Document Printing For best results, print this document in color, on letter size paper (8.5 x 11 in), double-sided. If using A4 paper (210 x 297 mm), configure your printer to scale the content of this document to A4 paper.

Intended Audience Any person in charge of installing, operating, and/or maintaining the Ilumipod Inground Tri-3 IP Optic 25 WW should read both the guide that shipped with it and this User Manual in their entirety before installing, operating, or maintaining this product.

Disclaimer ILUMINARC® believes that the information contained in this manual is accurate in all respects. However, ILUMINARC® assumes no responsibility for any error or omissions in this document. ILUMINARC® reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of ILUMINARC® to notify any person or company of such revision or changes. This does not constitute in any way a commitment by ILUMINARC® to make such changes. ILUMINARC® may issue a revision of this manual or a new edition of it to incorporate such changes.

Document Revision The Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 6 supersedes all previous versions of this manual. Please discard any older versions of this manual you may have, whether in printed or electronic format, and replace them with this version.

Table of Contents

Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7 i

Table of Contents 1. Introduction .......................................................................................................................... 1

What Is In the Box .............................................................................................................................. 1 Unpacking Instructions ....................................................................................................................... 1

Claims ....................................................................................................................................................... 1 Text Conventions................................................................................................................................ 1 Safety Notes ....................................................................................................................................... 2

Personal Safety ......................................................................................................................................... 2 Mounting and Installation ........................................................................................................................... 2 Power and Wiring ...................................................................................................................................... 2 Operation .................................................................................................................................................. 2

2. Product Description ............................................................................................................. 3

Features ............................................................................................................................................. 3 Additional Equipment ................................................................................................................................. 3

Overview ............................................................................................................................................ 4 Dimensions ........................................................................................................................................ 5

3. Installation ............................................................................................................................ 6

Installation Notes ................................................................................................................................ 6 Installation Sleeve Orientation .................................................................................................................... 6 Installation Sleeve Setup ............................................................................................................................ 6

AC Power ........................................................................................................................................... 7 Power Consumption .................................................................................................................................. 7 AC Plug ..................................................................................................................................................... 7 Power Wiring ............................................................................................................................................. 7

DMX Linking ....................................................................................................................................... 8 DMX Modes .............................................................................................................................................. 8 Signal Wiring ............................................................................................................................................. 8 Protocol Connectivity ................................................................................................................................. 8

Controllers .......................................................................................................................................... 9 DMX Controller .......................................................................................................................................... 9 Ilumicode Addresser ................................................................................................................................ 10

4. Operation ............................................................................................................................ 11

Ilumicode Addresser ......................................................................................................................... 11 Ilumicode Panel Description ..................................................................................................................... 11

Control Options ................................................................................................................................ 11 Programming .................................................................................................................................... 11

DMX Personality ...................................................................................................................................... 11 DMX Starting Address ............................................................................................................................. 11 Static Colors ............................................................................................................................................ 12 Dimmer ................................................................................................................................................... 12 Reset to Factory Settings ......................................................................................................................... 12

Menu Map ........................................................................................................................................ 12 DMX Values ..................................................................................................................................... 12

SOLID ..................................................................................................................................................... 12

5. Technical Information ........................................................................................................ 13

Product Maintenance ........................................................................................................................ 13 Product Repairs ................................................................................................................................ 13 Troubleshooting Guide ..................................................................................................................... 14 Photometrics .................................................................................................................................... 15 LED Disclaimer ................................................................................................................................. 16

LED Life .................................................................................................................................................. 16 LED Binning ............................................................................................................................................ 16 Color Rendering Index (CRI) .................................................................................................................... 16

Returns Procedure ........................................................................................................................... 17

Table of Contents

ii Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7

Contact Us .............................................................................................................................. 17

Technical Specifications ................................................................................................................... 18

Introduction

Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7 1

1. Introduction

Critical installation, configuration, or

operation information. Failure to comply with this information may render the product partially or completely inoperative, damage third-party equipment, or cause harm to the user.

Important installation or configuration

information. Failure to comply with this information may prevent the product from functioning correctly.

Useful information.

The term “DMX” used throughout this document

refers to the USITT DMX512-A transmission protocol.

What Is In the Box • Ilumipod Inground Tri-3 IP Optic 25 WW • Installation Sleeve • Warranty Card • Quick Reference Guide

Unpacking Instructions Immediately upon receiving a product from ILUMINARC®, carefully unpack the carton. Check the contents of the box to ensure that all parts are present and that they are in good condition.

Claims The carrier is responsible for any damage incurred during shipping. Therefore, if the received merchandise appears to have been damaged during shipping, the customer must submit the damage report and any related claims to the carrier, not ILUMINARC®. The customer must submit the report upon receipt of the damaged merchandise. Failure to do so in a timely manner may invalidate the customer’s claim with the carrier. For other issues such as missing components or parts, damage not related to shipping, or concealed damage, the customer must make claims to ILUMINARC® within 7 days of receiving the merchandise.

Text Conventions Convention Meaning

1–512 A range of values in the text 50/60 A set of mutually exclusive values in the text

DMX Primer The name of another publication or manual <SET> A button on the product’s control panel Settings A product function or a menu option

MENU > Settings A sequence of menu options 1–10 A range of menu values from which to choose in a menu

Yes/No A set of two mutually exclusive menu options in a menu ON A unique value to enter or select in a menu

Introduction

2 Ilumipod Inground Tri-3 IP Optic 25 WW User Manual Rev. 7

There are no user-serviceable parts inside this

product. Any reference to servicing you may find in this User Manual will only apply to properly certified ILUMINARC® technicians. Do not open the housing or attempt any repairs unless you are certified to do so.

Please refer to all applicable local codes and

regulations for the proper installation of this product.

Keep this manual for future consultation. If

you sell this product to another user, make sure that they also receive this manual.

In the unlikely event that your Ilumipod Inground Tri-3 IP

Optic 25 WW may require service, please contact ILUMINARC® Technical Support.

Safety Notes Please read all the following Safety Notes carefully because they include important information on how to install, use, and maintain this product safely.

Personal Safety • Avoid direct eye exposure to the light source while the product is on. • Always disconnect this product from its power source before servicing. • Always connect this product to a grounded circuit to avoid the risk of electrocution. • Do not touch this product’s housing when operating because it may be very hot.

Mounting and Installation • This product is for outdoor use and can be submerged (IP67). However, do not

submerge deeper than 1 m for more than 30 minutes. • Make sure there are no flammable materials close to this product while it is operating.

Power and Wiring • Always make sure that you are connecting this product to the proper voltage, as per the

specifications in this User Manual or on the product’s sticker. • CAUTION: When transferring product from extreme temperature environments, (e.g.

cold truck to warm humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a failure, allow product to fully acclimate to the surrounding environment before connecting it to power.

• Never connect this product to a dimmer pack. • Make sure that the power input cable is not cracked, crimped, or damaged. • Never disconnect this product by pulling or tugging on the power input cable.

Operation • The maximum ambient temperature is 113 °F (45 °C). Do not operate this product at a

higher temperature. • In case of a serious operating problem, stop using this product immediately!

Product Description


2. Product Description The Ilumipod Inground Tri-3 IP Optic 25 WW is a wash light intended for in-ground

installation. The product consists of a cast aluminum body containing a power supply, control unit, drive-over-rated glass lens cover, and tri-emitter LEDs.

Features • 1-channel warm white LED in-ground wash light • Operating mode, 1-channel: Dimmer • Five distinct dimming curves • IP67 stainless steel gland nuts for cable entry • Remotely addressable with Ilumicode Addresser • IP67 ingress protection • GORE™ valve • Drive-over-rated glass lens cover • High-power, 2.3 W (700 mA) tri-emitter LEDs

Additional Equipment • Ilumicode addresser required for product configuration (sold separately)

• The RDM2go, which includes a built-in Ilumicode addresser along with many other useful features, is now available.

• The Ilumicode addresser is required for product configuration (sold separately).

Product Description


Overview

Tri-emitter LEDs

Installation Sleeve

316 Stainless Steel Gland Nuts

Product Description


Dimensions

0.2 in (4 mm)

4.2 in (107 mm)

5.6 in (141 mm)

6.0 in (153 mm)

7 in (178 mm)

Installation


3. Installation

Always keep the power cables away from the signal cables by running

them in different conduits and using separate distribution boxes.

This product is intended for installation into

concrete or other hard pan substrate. It is not intended for installation into soft substrates including, but not limited to, soil or mulch.

Ilumipod Inground Tri-3 IP Optic 25 WW products can support

a distributed load of up to 3,000 kg (6,614 lb) when properly installed.

Installation Notes The Ilumipod Inground Tri-3 IP Optic 25 WW consists of two parts: the product housing and the concrete installation sleeve. The product housing is IP67-rated. The installation sleeve is not. Read the Installation Sleeve Setup instructions carefully. Do not use the product’s junction box to extend the power or signal cables to other units. This might compromise the IP rating of the junction box. Instead, use individual cables from the product to the corresponding distribution boxes.

Installation Sleeve Orientation You will have to run the AC power and signal cables from the base of the fixture into the installation sleeve. Position the installation sleeve so that the signal cable exits the sleeve using one of the two cable outlets. Use the opposite outlet for the power cable (refer to the following figure). This method will reduce the stress to the signal and power cables when setting the product down, while keeping them separated under the product’s housing.

Installation Sleeve Setup When setting up the installation sleeve, make sure that any water that may have entered can drain out of the sleeve. Locate the installation sleeve above the normal drainage level so the product is never under more than 1 m of water for more than 30 minutes (IP67) during heavy rain. In addition, make sure that the installation sleeve and the stainless steel collar are horizontal and even with the ground surface. This helps distribute the load uniformly over the product’s surface and avoids creating dangerous bumps.

Signal cable

Power cable

To power distribution box

To signal distribution box

Installation


Always connect the Ilumipod Inground Tri-3 IP

Optic 25 WW to a protected circuit with an appropriate electrical ground to avoid the risk of electrocution or fire.

Never connect the Ilumipod Inground Tri-3 IP

Optic 25 WW to a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer channel serves only as a 0 to 100% switch.

Make sure to connect the Ilumipod

Inground Tri-3 IP Optic 25 WW to a power line with the proper voltage and frequency, as per the specifications in this User Manual or on the product’s sticker.

AC Power The Ilumipod Inground Tri-3 IP Optic 25 WW has an auto-ranging power supply that works with an input voltage range of 100~240 VAC, 50/60 Hz. Make sure that you are connecting this product to the proper voltage, as per the specifications in this User Manual or on the product’s sticker.

Power Consumption To determine the power requirements for the Ilumipod Inground Tri-3 IP Optic 25 WW, refer to the label affixed to the side of the product. Alternatively, you may refer to the Technical Specifications. The listed current rating indicates the maximum current draw during normal operation.

AC Plug The Ilumipod Inground Tri-3 IP Optic 25 WW comes with a bare-ended power input cord for hardwired installation. Use the table and the illustration below to wire a plug.

Connection Wire (U.S.) Screw Color (U.S.) Wire (Europe) IP67 Pin

AC Live Black Yellow or Brass Brown 1 AC Neutral White Silver or Gray Blue 2 AC Ground Green/Yellow Green Green/Yellow 3

The listed current rating indicates the maximum current draw

during normal operation.

If you choose to bury the power or signal distribution

boxes, make sure that they are IP67-rated or greater.

Power Wiring You can connect the bare-ended, IP67-rated AC power cable from the product to an IP67-rated power connector or IP67-rated junction box. If using junction boxes, make sure to use IP67-rated conduit for surface installations.

Installation


The Ilumipod Inground Tri-3 IP Optic 25 WW

must be linked using DMX cable in a daisy chain (serial) fashion. To comply with the EIA-485 standard, no more than 32 products should be connected on one daisy chain without using a DMX optically isolated splitter. Doing otherwise may result in deterioration of the digital DMX signal.

USITT recommends limiting the total

length of the DMX cable (from the first product/controller to the last product) to 300–455 m (985–1,500 ft).

Disconnect the product from the AC power before

opening it.

The signal cable must match or exceed the

electrical characteristics of the Belden® 9841 cable for EIA RS-485 applications. You may also use CAT5, 5e, or CAT6 LAN cable.

DMX Linking You may link the Ilumipod Inground Tri-3 IP Optic 25 WW to a DMX controller using a standard DMX serial connection. If using other DMX products compatible with the Ilumipod Inground Tri-3 IP Optic 25 WW, you can control each individually with a single DMX controller. If you are not familiar with the DMX standard, or if you need information about the DMX cables needed to link the Ilumipod Inground Tri-3 IP Optic 25 WW to a DMX controller, you may download the DMX Primer from the ILUMINARC® website at http://www.iluminarc.com/reports/dmx-primer.

DMX Modes The Ilumipod Inground Tri-3 IP Optic 25 WW uses the standard DMX data connection for its SOLID personality. Refer to the Introduction chapter for a brief description of this mode. Refer to the Operation chapter to learn how to configure the Ilumipod Inground Tri-3 IP Optic 25 WW to work in this mode. The DMX Values section provides detailed information regarding the DMX mode.

DMX Mode DMX Address SOLID 512

Signal Wiring To provide signal for the Ilumipod Inground Tri-3 IP Optic 25 WW, you can connect the bare-ended, IP67-rated signal cable from the product to two IP67-rated signal connectors (DMX In/DMX Out) or use an IP67-rated junction box. In this case, make sure to use IP67-rated conduit.

Protocol Connectivity The Ilumipod Inground Tri-3 IP Optic 25 WW uses the USITT DMX 512 Protocol. The procedure below illustrates the recommended connection method.

http://www.iluminarc.com/reports/dmx-primer

Installation


If you have not configured the DMX starting address and

DMX mode for each product, they will all use their default values. This means that all products will operate in unison.

Controllers The Ilumipod Inground Tri-3 IP Optic 25 WW can operate with a standard DMX controller or the ILUMICODE addresser. The sections below provide information on how to connect these products to the corresponding controllers. The instructions to operate these products with each of the above controllers are in the Operation chapter of this manual.

DMX Controller The Ilumipod Inground Tri-3 IP Optic 25 WW can work with a standard DMX controller. The channel assignments will depend on the chosen personality (see the corresponding Menu Map section) and the DMX address assigned to each product (see the Programming section). The figure below illustrates how to connect the DMX controller to the Ilumipod Inground Tri-3 IP Optic 25 WW.

Installation


To assign individual DMX addresses to each product, you must connect the

Ilumicode addresser to each product, individually.

ILUMINARC® suggests that you connect no more than 20 products in

this mode and keep the total distance to less than 60 m (197 ft). Otherwise, you might need to use an optically isolated signal amplifier.

The RDM2go, which includes a built in ilumicode addresser

along with many other useful features is now available.

Ilumicode Addresser The Ilumipod Inground Tri-3 IP Optic 25 WW uses the Ilumicode addresser (“Ilumicode”) for configuration purposes. The diagram below shows how to connect the Ilumicode to this product. This connection will control multiple products at the same time, all having the same DMX address. Important: The Ilumicode must be used to configure this product. The Ilumicode can be purchased separately through your ILUMINARC® sales representative.

Operation


4. Operation

When you scroll through the menu options, you will see

many of them that do not correspond with the menu map. Skip them, as they do not work with the WW-only output products.

Ilumicode Addresser The Ilumipod Inground Tri-3 IP Optic 25 WW needs an external controller, the Ilumicode addresser (“Ilumicode”), to change its configuration.

Ilumicode Panel Description Button Function

<MENU> Exits from the current menu or function.

<ENTER> Enables the currently displayed menu or sets the currently selected value into the selected function.

<UP> Navigates upwards through the menu list and increases the numeric value when in a function.

<DOWN> Navigates downwards through the menu list and decreases the numeric value when in a function.

<POWER> Turns the unit on. The unit will turn off automatically after 30 seconds of inactivity.

Control Options You can set the Ilumipod Inground Tri-3 IP Optic 25 WW start address in the 001–512 DMX range. This allows for the control of up to 512 products in the 1-channel SOLID personality.

Programming Carry out all the programming procedures indicated below from the control panel. Refer to the Menu Map section to learn how the menu options relate to each other. Use <ENTER> and <MENU> to change levels in the Menu Map, moving right and left, respectively. Use <UP> and <DOWN> to move vertically within the Menu Map.

DMX Personality 1. Go to PERSON and select SOLID personality. 2. Make sure to rearrange the DMX addresses of all products in the current DMX

universe to avoid address overlapping.

DMX Starting Address 1. Go to DMX. 2. Select a starting DMX address (001–512).

Operation


DIM1 is the fastest dimming curve and DIM4 is the slowest.

Static Colors 1. Go to STATIC. 2. Select a color (COOL). 3. Select a color value 000~255 (0–100%).

Dimmer This setting gives the user four different options to simulate the dimming curve of an incandescent lighting product.

1. Go to DIMMER. 2. Select a dimming curve (OFF or DIM1–4).

Procedure:

DIMMER Description OFF Dimmer curve is linear with fader

DIM1 Non-linear (fastest) DIM2 Non-linear (fast) DIM3 Non-linear (slow) DIM4 Non-linear (slowest)

Reset to Factory Settings 1. Go to SETTINGS > RESET. 2. Select YES or NO.

Menu Map

Main Level Programming Levels Description

DMX 001–512 Sets the DMX starting address

PERSON SOLID 1-channel: Dimmer

DIMMER OFF Dimmer works in linear mode

DIM1 Dimmer works in non-linear mode, from fast to slow

DIM2

DIM3

DIM4

STATIC COOL 000–255 Configures the static color

SETTINGS RESET YES Resets unit to factory default settings

NO

DMX Values SOLID

Channel Function Value Percent/Setting 1 Dimmer 000 255 0–100%

Technical Information


5. Technical Information

Always dry the external optics and glass surfaces carefully

after cleaning them.

If you still experience technical problems after

trying the solutions in the Troubleshooting Table, contact ILUMINARC® Technical Support.

Product Maintenance To maintain optimum performance and minimize wear, clean the products frequently. Usage and environment are contributing factors in determining the cleaning frequency. As a general guideline, products should be cleaned at least twice a month. Dust build-up reduces light output, performance, and can cause overheating. This can lead to reduced light source life. For products containing external optical lenses, clean them periodically to optimize light output. The cleaning frequency depends on the environment in which the product operates. Damp, smoky, or particularly dirty surrounding can cause greater accumulation of dirt on the product’s optics, requiring more frequent cleaning. To clean a product: • Disconnect the product from power. • Wait until the product is at room temperature. • Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on the

external surfaces. • Clean all external glass optics and glass surfaces with a mild solution of glass cleaner or

isopropyl alcohol, and a soft, lint-free cotton cloth or lens-cleaning tissue. • Apply the solution directly to the cloth or tissue and wipe any dirt and grime to the outside

edge of the lens. Gently polish the external glass surfaces until they are free of haze and lint.

Product Repairs ILUMINARC® strongly advises you against attempting any repairs to this product unless you are an authorized ILUMINARC® technician. ILUMINARC® presents the information contained in the Troubleshooting Guide as potential solutions only. In most cases, opening the product’s housing will invalidate its warranty.



Troubleshooting Guide Symptom Cause(s) Action(s)

Circuit breaker/fuse keeps tripping/blowing

Excessive circuit load Check total load placed on the electrical circuit

Short circuit along the power wires Check for a short in the electrical wiring

Product does not power up No power Check for power on power outlet Loose or damaged power cord Check power cord Faulty internal power supply Return for service to ILUMINARC®

Product does not respond to DMX

Wrong DMX addressing Check Control Panel and product addressing Damaged DMX cables Check DMX cables

Wrong polarity on the controller Check polarity switch settings on the controller

Loose DMX cables Check cable connections Faulty DMX interface Return for service to ILUMINARC® Faulty Display/Main board Return for service to ILUMINARC®

DMX signal problems

Non-DMX cables Use only DMX-compatible cables

Bouncing signals

Install terminator as suggested in the DMX Primer from the ILUMINARC® website at http://www.iluminarc.com/reports/dmx-primer.

Long cable/low level signal Install an optically coupled DMX splitter right after the product with the strong signal

Too many products Install an optically coupled DMX splitter after product #32 or before

Interference from AC wires Keep DMX cables separated from power cables or fluorescent/black lights





Photometrics Filename: ILUMIPOD INGROUND TRI-3 IP OPTIC (25°) WW

Manufacturer: ILUMINARC®

Luminaire: Ilumipod Inground Tri-3 IP Optic 25 WW

Lamp Output: 1 lamp, rated lumens/lamp: 400

Max Candela: 2,885.7 at Horizontal: 0°, Vertical: 1°

Input Wattage: 9.8

Luminous Opening: Point

Test: 20120523

Test Date: 2012-05-23

Test Lab: ILUMINARC R&D

Photometry : Type B

CIE Class: Direct

Flood Summary Efficiency Lumens Horizontal Spread Vertical Spread

Field (10%): 52.7% 210.6 29.1 29

Beam (50%): 23.7% 94.9 15.2 14.5

Total: 62.5% 250.0

Photometrics Pro 1.3.21 copyright 2003-2012 by jSolutions, Inc. Reported data calculated from manufacturer's data file, based on IES recommended methods.



LED Disclaimer LED Life

ILUMINARC® rates LED lifetime based on lumen depreciation of 70% of the original output, with data provided by the manufacturer of the LED. Data from the manufacturer of the LED are not independently verified or measured by ILUMINARC®. When the product is operating in optimal environmental conditions, the LED lifetime is rated to be 50,000 to 70,000 hours by the LED manufacturer.

LED Binning LED manufacturers sort LEDs into “bins,” based on variances in color, output intensity, and the frequency at which the semiconductor operates. ILUMINARC® strives to hold its LED manufacturers to the highest standards of binning to optimize consistency in output from product to product. However, the availability of a single bin cannot be guaranteed. With that in mind, ILUMINARC® has developed a rigorous control system to seek the best-achievable consistency in color and output.

Color Rendering Index (CRI) CRI is an industry standard method to compare properties of different types of light sources. There are known limitations and inconsistencies related to CRI. Results may vary depending on the environmental factors involved. For this reason, the U.S. Department of Energy (DOE) states that CRI should be considered as one point of reference among others in evaluating white LED products and systems. The following is an excerpt of recommendations from the DOE:

1. Identify the visual tasks to be performed under the light source. If color fidelity under different light sources is critically important (for example, in a space where color or fabric comparisons are made under both daylight and electric lighting), CRI values may be a useful metric for rating LED products.

2. CRI may be compared only for light sources of equal correlated color temperature. This applies to all light sources, not only to LEDs. Also, differences in CRI values of less than five points are not significant, e.g., light sources with 80 and 84 CRI are essentially the same.

3. If color appearance is more important than color fidelity, do not exclude white light LEDs solely on the basis of relatively low CRI values. Some LED products with CRIs as low as 25 still produce visually pleasing white light.

4. Evaluate LED systems in person and, if possible, on-site when color fidelity or color appearance are important issues.

Source: DOE publication: PNNL-SA-56891, January 2008



ILUMINARC® reserves the right to use its own

discretion to repair or replace returned product(s).

Always keep the original box and all packaging material as you

will need those to ship the product back to ILUMINARC®.

Returns Procedure You must send the merchandise prepaid, in the original box, and with its original packing and accessories. ILUMINARC® will not issue call tags. Call ILUMINARC® and request a Return Merchandise Authorization Number (RMA #) before shipping the product. Be prepared to provide the model number, serial number, and a brief description of the cause for the return. The user must clearly label the package with an RMA #. ILUMINARC® will refuse any product returned without an RMA #. DO NOT write the RMA # directly on the box. Instead, write it on a properly affixed label. Once you receive the RMA #, please include the following information on a piece of paper inside the box: • Your name • Your address • Your phone number • The RMA # • A brief description of the problem Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be the customer’s responsibility. FedEx packing or double-boxing are recommended.

Contact Us

USA WORLD HEADQUARTERS General Information – ILUMINARC Address: 5200 NW 108th Avenue Sunrise, FL 33351 Voice: (954) 923-3680 Fax: (800) 544-4898

Technical Support Voice: (800) 762-1084 Email: [email protected] World Wide Web www.iluminarc.com

EUROPE

General Information - Chauvet Europe BVBA Address: Stokstraat 18 9770 Kruishoutem Belgium Voice: +32 9 388 93 97

Technical Support Email: [email protected] World Wide Web www.chauvetlighting.eu

General Information - Chauvet Europe Ltd. Address: Unit 1C Brookhill Road Industrial Estate Pinxton, Nottingham, UK NG16 6NT Voice: +44 (0)1773 511115 Fax: +44 (0)1773 511110

Technical Support Email: [email protected] World Wide Web www.chauvetlighting.co.uk

MEXICO General Information - Chauvet Mexico Address: Av. Santa Ana 30 Parque Industrial Lerma Lerma, Mexico C.P. 52000 Voice: +52 (728) 285-5000

Technical Support Email: [email protected] World Wide Web www.chauvet.com.mx

Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux contact the dealer of record. Follow their instructions to request support or to return a product. Visit our website for contact details.

mailto:[email protected]

http://www.iluminarc.com/


http://www.chauvetlighting.eu/


http://www.chauvetlighting.co.uk/


http://www.chauvet.com.mx/

Ilumipod Inground Tri-3 IP Optic 25 WW User Manual


Technical Specifications Dimensions and Weight Length Width Height Weight

6.0 in (153 mm) 6.0 in (153 mm) 7.0 in (178 mm) 4.6 lb (2.0 kg) Note: Dimensions in inches rounded to the nearest decimal digit.

Electrical Power Supply Type Range Voltage Selection Switching (internal) 100 to 240 VAC, 50/60 Hz Auto-ranging

Parameter 120 V, 60 Hz 230 V, 50 Hz Consumption 10 W 11 W

Operating current 0.2 A 0.1A Power I/O Input Output Connectors Open Wire N/A Cord plug N/A N/A

Light Source Type Power Lifespan LED 2.3 W 50,000 hours

Color Color Temperature

Quantity Current

Warm White 3100 K 3 700 mA Photometric Parameter Standard 25º Optics

Illuminance @ 5 m 100 lx Beam angle 15° Field angle 29°

Thermal Max. External Temperature Cooling System 113 °F (45 °C) Convection

DMX I/O Connectors Connector Type Channel Range Open Wire Open Wire 1

Ordering Product Name Item Code UPC Number Ilumipod Inground Tri-3 IP

Optic 25 WW 01630585 781462209339

Date post:	29-Jul-2018
Category:	Documents
Upload:	truongminh
View:	213 times
Download:	0 times

Ilumipod Inground Tri-3 IP Optic WW User Manual … · 2016-04-18 · company names, trademarks...

Documents