INDUSTRIAL Fuel Air Separation Systemairdogdiesel.com/wp-content/uploads/2017/05/A3SPBT401...FUEL...

INDUSTRIALFuel Air Separation System

PROTECTED UNDER THE FOLLOWING PATENTS CANADA UNITED STATES OF AMERICA MEXICO 2,108,391 5,355,860; 5,746,184; 6,729,310 270409

NEW ZEALAND ITALY AUSTRALIA HONG KONG ECUADOR 532356 1362177 2005101054 1061420 PL10-2021

Additional Foreign Patents Issued and Pending in Europe, South America, Japan, and China!

INSTALLATION MANUAL

For Trucks Equipped withCATERPILLAR® 3406 A, B, or C Engines

Kit No. A3SPBT401

NOW WITH DEMAND FLOW

Providing “Test Cell Performance” in “Real World Conditions” Since 1993!

Proudly Made in the USA

www.pureflowtechnologies.com 1-573-635-0555or 1-877-463-4373

Revised 2/24/17

2

THE RIGHT CHOICE FOR YOUR DIESEL ENGINE!

CARB Executive orders No. D-595-1 & D-595U-1, permit the advertisement, sales, andinstallation in California of AirDog®, AirDog®II, Fuel Preporator®, and Fuel Preporator®II

Low Fuel Pressure Switchand LED Indicator

Lets you know when to service the fuel filter and water separator

before suffering power loss.NO MORE GUESSING!

New Design 4G-HD Fuel Pump Pump shaft, stabilized with bearings on each end, holds the gerotor in virtually perfect

alignment for quiet running and extended longevity!

Quick Change MotorIf necessary, the motor can be removed

and replaced in a matter of minutes.

New LoveJoy Coupler System The LoveJoy Coupler System is

self-aligning and eliminates virtually all vibrations.

Dual Port Pump Balances the gerotor for quiet operation and higher flows.

Protective Wire ScreenIn water separator nipple.

s FPII-150 & FPII-200 8¼” W x 3 7/8” D x 12¾” T s FPII-125 7” W x 3” D x 10” T s

6 Micron Particulate Filters Long Lasting MicroGlass Media

Water Separator/Prefilter Long Lasting Wire Mesh Media

Bearings

Positive Air Separation with primary air discharge port.

Demand Flow System Easy installation, only one small line connected to the engine return line to

return air/vapor to the tank.Adjustable Regulator

For just the right fuel pressure.

INDUSTRIALFuel Air Separation System

3

SYSTEM OVERVIEW

Welcome to the AirDog® Fuel Preporator®

Fuel Air Separation System for Class 8 Trucks

The AirDog®, with ADVANCED FUEL AIR SEPARATION, DEMAND FLOW, ADJUSTABLE REGULATOR, LOW PRESSURE SWITCH with LED INDICATOR and the NEW 4G-HD FUEL PUMP, is a premium fuel filtration and delivery system for trucks equipped with Caterpillar® 3406 A, B, or C Engines.

Air & Vapor are compressible! When Air/Vapor is present in a fuel injection system the pres-sure buildup and injection of fuel is delayed while the Air/Vapor is being compressed. This delay retards the injection timing causing a shorter power stroke and low power, increased fuel consumption and increased exhaust emissions. Preventing the formation of vapor from pump cavitation and removing entrained air from the fuel flow to the injectors restores Cor-rect Injection Timing. Diesel engines equipped with the AirDog® can now perform as designed, delivering “test cell” performance while in “real world” use!

The AirDog® removes water, particulates and most importantly, the air that becomes entrained in diesel fuel, from the fuel flow to your engine. The entrained air and vapor that is separated from the fuel is returned to the fuel tank through a small return line. The fuel flow to the engine’s transfer pump is at a NET POSITIVE PRESSURE HEAD preventing cavitation and the formation of vapor thus overcoming the performance related problems from plugged fuel filters, high altitude operation and torque loss at higher engine RPM’s.

All AirDog® products are manufactured with a personal touch, unsurpassed attention to detail and the most stringent quality assurance!

TYPICAL INSTALLATION LAYOUT

Figure 1

The AirDog® requires only one small return line connected to the engine return line, for quick and easy installations.

Transfer PumpPositive Fuel Pressure to

Transfer Pump

Air/Vapor Return Line

Fuel Supply Line

Entrained Air in Fuelfrom Agitation & Sloshing

Fuel Preporator®

Injector Pump

4

PureFlow® Technologies, Inc.AirDog® FPII-150 CATERPILLAR® 3406A, B, & C

TABLE OF CONTENTSSection 1………….........…….…...………............…..…………..….Table of ContentsSection 2………………….................….…….…...…Installation and Safety GuidelinesSection 3……………………..........………………………………………..…Parts List

INSTALLATION PROCEDURESSection 4…………………………...........….....Selecting the Best Mounting LocationSection 5………………………............………………..AirDog® & Mounting Brackets

Fuel Lines, Fittings & Fuel Pressure Sensor SwitchSection 6A…………………...........…………………………..Fittings & Sensor SwitchSection 6B………………………...………...............Fuel Line from AirDog® to EngineSection 6C…………………..............………...…….AirDog® Air/Vapor Return to TankSection 6D…………………………………..……...........……....From Tank to AirDog®

Section 7…………………………...............………Secondary Fuel Filter Modification

Electrical System, Low Pressure Switch & Filter MonitorSection 8……………………….............………..……….Electrical Harness InstallationSection 9……………………..........……………………………...………Initial Start Up

INSTALLATION PROCEDURESSection 10…………..............………………..…...…..Filter Service RecommendationsSection 11………………..............……………………....…..………Pressure Regulator

Section 1 Table of Contents

5


The installation of your AirDog® can be made relatively easy by following the steps outlined in this manual, and:

1. Inventory the package components. Immediately notify PureFlow® Technologies, Inc., of any missing or damaged parts.

2. Read the installation manual completely. Understand how the system operates and the installation recommendations before beginning.

3. Proper location of the AirDog® on the vehicle is essential. Consider hazards presented to the equipment by road debris and the elements.

4. The installation recommendations and guidelines contained herein are suggestions only. Individual installations may vary.

5. Use diesel compatible thread sealer when installing fittings with NPT threads. (Loctite® 545 Thread Sealer is diesel compatible.)

DO NOT REMOVE FACTORY INSTALLED SECONDARY FUEL FILTERS. REMOVAL OF A FACTORY INSTALLED SECONDARY FUEL FILTER MAY VOID YOUR ENGINE WARRANTY.

SAFETY GUIDELINES!CAUTION: Chock the vehicle’s tires to prevent rolling.

CAUTION: Disconnect the battery cables before proceeding with the AirDog® installation.

CAUTION: Wear safety glasses when operating power tools such as drills and grinders or when using a punch or chisel.

CAUTION: Do Not drill into or weld the top of the frame rail or within 1 ½” of the frame rail flange on the side of the frame rail.

CAUTION: Route the fuel lines and electrical harnesses keeping them away from hot exhaust components and/or moving parts. Properly secure the fuel lines and electrical harnesses to prevent chaffing.

If you are uncertain of any installation procedure, contact:PureFlow® Technologies, Inc. for technical assistance.

NOTE: The pictures used in this manual are for example only and may not depict the exact components as found on your truck.

Section 2 Installation & Safety Guidelines

6


PLEASE NOTEDue to the many variables in components and arrangement of those components in the many different truck models, the installation kit contains only the mounting brackets, mounting hardware, wiring harness and basic fuel fittings needed to install AirDog®.

Installation Parts ListSection 3 Parts List

QTY Description Part Number Image

1 Installation Manual 206-1-0401

1 AirDog® FPII-150

1 Wiring Harness with Indicator Light 5E-2-010

1 Fuel Filter Monitor Light Plate 201-3-0004-S

1 Fuel Pressure Sensor (5 psi) 5C-9-007

1 7 ft. Section DOT Air/Vapor Return Line 4C-1-02-05-010

1 Sandwich Mounting Bracket Kit for AirDog® & Champ 002-3C-0010-SBF Includes: 1 Front & 1 Back 002-3C-0011-SBB Center Bracket 002-3C-0006PCB

2 Mounting Bracket 002-3C-0003 002-3C-0004

1 #6 Return “T” 4A-4-04-06-06-06-4-S

2 # 6 JIC Female Swivel x 3/8” Pushlock Hose Barb 4A-1-09-06-06-SZ

1 #6 Swivel x #6 JIC Forged 90° 4A-2-04-06-06-S

1 Hand Primer Pump Replacement Kit Includes: 1 Cap 002-4G-0006 1 Gasket 002-4G-0007

2 #10 Straight JIC Flare x 1/2” NPT Fitting 4A-1-01-10-08-S

2 #10 - 90° Swivel x JIC Flare Fitting 4A-2-04-10-10-S

1 #6 JIC Flare x 1/4” NPT Return Fitting 4A-1-01-A-C-SZ

1 Grommet 5J-1-1-04-2758

908-01-0401-IFK Return Line Fitting Kit

908-08-0800 AirDog® Standard Fitting Kit

901-08-0100 1 Hardware Kit, Includes:

4 ea 3/8” x 1-1/4” Hex Head Bolt 1J-1-C20SZ 4 ea 3/8” Nut 1S-1-CSZ 4 ea 3/8” Lock Washer 1R-6-CSZ 4 Socket Head Cap Screws, 1/4-20 x 2” Lg 1L-A32C 4 Lock Washers, 1/4” 1R-6-AC 4 Hex Nuts, 1/4-20 1S-1-AC

901-08-0100-SB 1 Hardware Kit, Includes:

3 ea 3/8”-16 x 3-1/2” Hex Head Bolt 1J-1-C56SZ7 ea 3/8” Nut 1S-1-CSZ 7 ea 3/8” Lock Washer 1R-6-CSZ 4 Screw, 3/8-16x1” F/H SHCS 1M-C16SZ

7


Assess Desired Mounting Location for Required Drilling or Use of Universal Sandwich Bracket

Selecting the Best Location to Mount the AirDog®

When possible, mount the AirDog® in the same location of the original fuel filter.Installing the AirDog® at the proper location on the vehicle is most important. When deciding where to locate the AirDog®, the following points should be considered:

• Best relationship to the transfer pump and the original primary fuel filter location.• Protection from the elements and road debris.• Accessibility for service.

CAUTION: DO NOT mount the AirDog® directly on the engine. Mounting the AirDog® directly on the engine will immediately void your AirDog® Warranty!

Figures 2 thru 4 show examples of different AirDog® installations. There are many variations in the arrangements of the components on the various trucks. With a little ingenuity, the AirDog® can be successfully installed on any Class 8 Truck.

Figure 2 shows the AirDog® mounted on the frame under the steering column to the rear of the shock absorber. Figure 3, in a different truck, shows the AirDog® mounted under the steering column ahead of the shock absorber. Figure 2 Figure 3

NOTE: When mounting the AirDog® at this location, check for clearance with the tire turned both toward and away from the frame.

Section 4 Selecting the Best Mounting Location

This installation on a short nose“Day Cab” is on the driver’s side,

behind the battery box.

Figure 4

See Universal Sandwich Mounting Bracket Guide on Next Page

8

PureFlow® Technologies, Inc.AirDog® FPII-150 CATERPILLAR® 3406A, B, & CSection 4 Selecting the Best Mounting Location

NO DRILL Universal Sandwich Mounting BracketNow included with all engine specific AirDog FPII Kits!!

Sandwich bracket comes with all hardware that is needed and NO DRILLING

Sandwich bracket can be used in any combination of ways to fit your truck.

Sandwich bracket slides right over existing frame.

9


Secondary Fuel Filter

Transfer Pump

Primary Fuel Filter

Injector Pump

1985 “3406 B” Caterpillar Engine

Figure 7

Section 5 Mounting the AirDog®

Section 5: Mounting the AirDog® on the Truck’s Frame!

5-1. Disconnect the fuel lines and remove the primary fuel filter.

Figure 5 Figure 6

5-2. Mount the AirDog® as close to the original location of the primary fuel filter as possible. This will allow you, in most cases, to use the original fuel supply line from the fuel tank and also the fuel line to the engine.

NOTE: Mount the AirDog® on the truck frame. DO NOT mount the AirDog® on the engine! Mounting the AirDog® on the engine will immediately void your AirDog® warranty.

10


Mounting the AirDog® on the Truck’s Frame, cont’d!5-3. Loosely assemble the mounting brackets and filters to the AirDog®.

5-4. Hold the AirDog®, with the brackets and filters attached, next to the frame at the selected mounting location. Check for clearance. If mounted between the frame and steer tire, turn the steering wheel fully to the left and right to check for tire clearance.

Figure 8 Figure 9

5-5. While holding the AirDog® at the selected mounting location on the frame, mark and center punch each hole location.

WARNING! DO NOT DRILL INTO OR DAMAGE ANY WIRING, AIR LINES OR OTHER COMPONENTS LOCATED BEHIND THE FRAME RAIL.

5-6. Drill a 3/8” hole at each of the 4 previously marked locations.

Figure 10

Figure 11

5-7. Loosely assemble the mounting bracketsto the frame.

5-8. Loosely assemble the AirDog® on the brackets.

Figure 12


11


Mounting the AirDog® on the Frame, cont’d!5-9. After mounting the AirDog® on the brackets, snug the fasteners to achieve a good relaxed fit.

5-10. Properly tighten all of the fasteners.

NOTE: These steps are necessary to prevent stress cracks from forming in the mounting brackets due to road vibration and bouncing.

Figure 13

FUEL LINE OVERVIEWThe AirDog® has been engineered to eliminate fuel related problems. It is important that the fuel lines are assembled and installed properly so as not to cause flow restriction. When possible, use the fuel lines that are on the vehicle. This will reduce your installation costs and make the installation go much more quickly.

NOTE: On various class 8 trucks, the manufacturer may use other than traditional steel braid fuel lines. These lines require special fittings. The fittings used with the original primary fuel filter are specific to the fuel lines used on the truck. When possible, mount the AirDog® in the location that will allow the use of the original fuel lines and fittings.

Inspect the original fuel lines for size, length, and condition. If the fuel lines are in good condition and the correct size and length to adequately reach the AirDog®, you may want to go ahead and use them. If any of the fuel lines need to be replaced, it is recommended that the fuel lines selected meet or exceed DOT requirements.

Fuel Supply Line: The fuel supply lines from the tank to the AirDog® and to the engine should be size 10 or, at the absolute minimum, size 8 (1/2” ID).

Air/Vapor Return Line: The AirDog® Air/Vapor return line can be connected to the engine’s return line. A size 6 is adequate for the Air/Vapor return line.

Primary Fuel Filters: It is most important that there are no fuel filters between the fuel tank and the AirDog® or between the AirDog® and the engine’s transfer pump to plug and cause restriction. These filters should be removed from the system as part of the AirDog® installation.

Secondary Fuel Filters: DO NOT REMOVE SECONDARY FUEL FILTERS. This is the filter between the transfer pump and the engine.


12


Figure 15 Figure 14

Figure 16 Figure 17

Installing the Fuel Fittings and Pressure Sensor Switch!IMPORTANT: Use diesel compatible thread sealer when installing NPT fittings.

NOTE: Figures 14 & 15 illustrate the installation of straight fittings. However, in some instances 90º fittings may be required to connect the fuel lines to the AirDog®. Two 90º fittings have been included in the kit for this purpose.

6A-1. Install the straight #10 JIC x ½ NPT fuel fitting in the AirDog® fuel port marked “ENGINE”.

6A-2. Install a straight #10 JIC x ½ NPT fuel fitting into the fuel inlet port next to the regulator.

6A-3. Install the ¼” NPT x #6 JIC Male return fitting into the Air/Vapor return port marked “TANK”

6A-4. Remove the 1/8” NPT plug from the end of the pre-installed 45° fitting in the AirDog® base. Install the pressure sensor switch into the 45° fitting.

Use diesel compatible thread sealer on all NPT threads!

Section 6B: Connecting the AirDog® to the Transfer Pump on the Engine!6B-1. Connect the fuel line that originally connected the primary fuel filter (See Step 5-1) to the transfer pump to the AirDog® “out to Engine” port. If the fuel line is not in good enough condition or the proper length to make the connection, replace it with a new fuel line!

Figure 18

Figure 19

3406B Plunger TypeTransfer Pump

Section 6 Fuel Lines

13


6C-2. Measure and cut the length of fuel line required, when properly routed, to connect the AirDog® Air/Vapor return port to the new return “T” installed on the injector pump. Assemble the fuel return line end fittings per

Figure 22

6C-3. Route and connect the new Air/Vapor return line from the AirDog® to the injector pump return “T”. Properly tighten the fittings. Secure the fuel line as necessary to prevent abrasion and chaffing

SECTION 6C: Installing the AirDog® Return LineThe AirDog® air/vapor return line may be connected directly to the injector pump fuel return line. The AirDog® requires only one small return line making the installation quick and easy!

NOTE: It is recommended to use a # 6 size line for the Air/Vapor return.

Connecting the AirDog® Air/Vapor return to the engine fuel return line!

6C-1. Disconnect the fuel return line connected to the top of the injector pump and install the “T” included in the installation.

Figure 21 Figure 20

Fuel Return Line


OR

Assembly Instruction for Hose Barb1. Cut hose line to length.2. Apply oil to fitting.3. Push fitting into line until seated.

Figure 23

14


Connecting the AirDog® fuel supply line to the Fuel Tank!6D-1. Inspect the fuel supply lines that connect the fuel tank(s) to the primary fuel filter for size, length, and condition. If a fuel line has deteriorated or if it is too short to connect to the AirDog®, replace it or make an extension as necessary.

6D-2. If it is necessary to replace the fuel line, measure and cut the length of fuel line required when properly routed and secured to make the connection from the fuel tank to the AirDog®. Assemble the fuel line per standard procedures.

6D-3. Route the fuel supply line from the fuel tank to the fitting on the AirDog® fuel inlet port marked “IN”. Figure 24

Figure 25

6D-4. Connect the fuel supply line from the fuel tank to the fitting. Secure the line to prevent chaffing and abrasion.

SECTION 7: The Caterpillar® Secondary Fuel Filter Modification!All Caterpillar® diesel engines are equipped with a secondary fuel filter mounted on the engine. The filter head usually has a Hand Primer Pump attached to make priming and starting the engine easier after filter changes.

However, certain passage ways in the filter head and the valves in the hand primer pump are restrictive to fuel flow and negatively affect engine performance.

Figure 26 Figure 27 Figure 28

NOTE: In most cases, the filter head can be drilled out without removing it from the engine!

Secondary Fuel Filter Small, Restrictive Passageway RestrictiveOne-way Check

Valves

1985 3406 BHand Primer Pump


15


Restricted PassagewayBefore Porting Process

The Caterpillar® Secondary Fuel Filter Modification!Perform the following steps to improve fuel flow and engine performance.

7-1. Remove the hand primer pump and fuel filter from the filter head.

Unrestricted PassagewayAfter Porting Process

Figure 29 Figure 30

7-2. Using a 3/8” bit, carefully drill out the passage that carries the fuel into the fuel filter.

Figure 31

7-3. Remove all burrs and shavings then, install the cap and gasket (included in the kit) on the filter head. Also, re-install the fuel filter.

Figure 32

NOTE: The primer pump replacement cap (included in the kit) has also been ported.

Figure 33

Section 7 Secondary Fuel Filter

16


ELECTRICAL HARNESSThe AirDog® wiring harness has a low pressure switch and an amber LED indicator light as standard equipment. VERY IMPORTANT: The LED Indicator Light will remain off. Should pressure flow to the engine drop below minimum requirements, the light will immediately illuminate. First check the water separator. Then, check the screen in the water separator nipple. Clean or replace as necessary.

THE AIRDOG®, WIRING HARNESS.

AirDog® Pump Motor Lead

Pressure Sensor/Switch Lead

Indicator Light & Lead

Battery Positive Lead

Battery Negative Lead

Relay Lead Figure 34

Securing the Relay to the Vehicle8-1. Secure the Relay to the vehicle. This picture shows the Relay mounted on the firewall.

Figure 35

8-2. Route the pump motor and indication light sensor lead to the AirDog®. Connect the 2 pin Deutsch connector on the end of the wiring harness to the pump motor lead.

Figure 36 Figure 378-3. Connect the lead with the green seal to the “low fuel pressure” sensor switch.

Section 8 Electrical Harness

17


Routing the Indicator Light Lead and Relay Trigger LeadThe Relay Trigger Lead must be connected to a contact point that is electrically “HOT” when the starter key is in the “ON” position. This could be either in the engine compartment or inside the dash such as a spare fuse holder in the fuse panel or on the ignition switch itself

Note: DO NOT connect the relay lead to a point that is “HOT” when the starter key is in the ACCESSORY ON position.

To allow entry for the Indicator Light and Relay Trigger Lead through the firewall:

8-4. Peterbilts and Kenworths have access holes located below the steering column. Remove the plug and route the leads through the hole.

Figure 38 Figure 39

8-5. For other make trucks, drill a 5/8” hole in firewall to allow entry of the Relay Trigger Lead / Indicator Light harness into the cab.

Figure 40 Figure 41

8-6. Route the red, relay trigger wire and indicator light lead through the firewall. Be sure to seal the opening or install a grommet around the wire loom to prevent water leakage and protect it from chaffing.

Be sure to seal the opening or install a grommet around the wire loom to prevent water leakage and for protection from chaffing.


18


INSTALLING THE FILTER MONITOR INDICATOR LIGHT.Amber LED Indicator Light!

Figure 448-9. Select a location on the dash board that is easily visible to the driver.

Figure 45 Figure 46

8-10. Remove the dash components as necessary to access the area behind the selected location.

Routing the Indicator Light and Relay Trigger Lead, cont’d!8-7. Connect the Relay Trigger lead to a terminal on the ignition switch that is “HOT” when the ignition switch is in the “ON” or “RUN” position.

Battery

Ignition Accessory Figure 43

Figure 42

8-8. Route the relay trigger lead (Red Wire) to the fuse panel and connect it to a fuse holder that is “HOT” when the key is in the “ON” or “RUN” position.

OR


19


INSTALLING THE FILTER MONITOR INDICATOR LIGHT, Cont’d

8-11. Drill a 5/16” hole at the selected location. Be very careful when drilling. Do not damage components located behind the dash.

Figure 47 Figure 48

8-12. Install the Dash Plate and Indicator Light in the dash. Connect the Indicator Light Lead to the connector on the wiring harness.

8-13. Re-install the removed dash components to their original position.

CONNECTING THE POWER SUPPLY LEADSThe power supply leads can be easily connected to the appropriate contacts on the alternator. However, any high amperage terminal that is always “HOT” is OK for the Positive + (RED) lead. Be sure the NEGATIVE ▬ (BLACK) lead is connected to a reliable Chassis Ground.

8-14. Route the Red & Black power supply leads to the alternator. Connect the Black (-) ground lead to the alternator Ground connection.

Figure 49 Figure 50

8-15. Connect the Red (+) positive lead to the alternator Hot Lead going to the battery.


20


SECTION 9: INITIAL START UP PROCEDUREThe AirDog® is a self priming system. However, to prevent damage to a dry seal and reduce the life expectancy of the system, it is suggested to pre-fill the water separator/pre-filter with diesel fuel to the bottom of the “NUT PLATE”.

r 9-1. Pre-fill the water separator/pre-filter with diesel fuel up to the bottom of the nut plate.

r 9-2. Turn the starter key to the on/run position.

r 9-3. The AirDog® should now be running and pumping fuel, bleed the fuel line to the engine by loosening the fuel line connection at the engine fitting. As soon as the line is purged of air, tighten the fuel fitting.

NOTE: Put a rag or shop towel around the fitting to prevent fuel splatter or spray. Catch all spilled fuel and dispose of properly.

r 9-4. Start your engine!

RECHECK ALL FUEL FITTINGS FOR LEAKS. BE SURE ALL LINES ARE PROPERLY SECURED TO PROTECT FROM CHAFFING AND ABRASION. RECHECK ALL ELECTRICAL LINES, SECURE AS NECESSARY.

Section 9 Initial Startup

21


Servicing the AirDog® Fuel Filter and Water Separator/PrefilterThe AirDog® low pressure switch monitors the fuel filter and water separator!

FUEL FILTER: Plugging of the fuel filter will cause the AirDog® Indicator Light to illuminate. Replace the fuel filter as necessary! Typically our fuel filters are good for a 40,000 mile service period because they are micro glass media instead of typical paper.

It is recommended to replace the fuel filter at 40,000 miles of service OR when the AMBER Indicator Light illuminates, which ever comes first!

When replacing the fuel filter, be sure to clean the under side of the AirDog® base. It is not necessary to pre-fill the fuel filter with fuel, the AirDog® will fill the filter and prime the system automatically. Follow the instructions on the filter for proper tightening procedures.

Figure 51

The Water Separator/Pre-filter

WATER SEPARATOR: Should the water separator/pre-filter or the wire screen in the nipple become plugged, preventing sufficient operating pressure flow to the engine, the Amber Indicator Light will immediately illuminate

Check the water separator/pre-filter for plugging. Clean or Replace as necessary! If the light continues to be on, check the screen in the water separator/pre-filter nipple for debris and plugging. Clean as necessary!

Replace the water separator if it becomes damaged or permanently plugged. Servicing of the water separator simply requires draining at regular intervals. It is suggested to check/drain the water separator weekly or as needed should you experience excessive ‘water in fuel’ conditions. Before re-installing the water separator after cleaning, be sure to clean the under side of the AirDog® base. Follow the instructions printed on the water separator/pre-filter for proper tightening procedures. DO NOT over tighten and damage the water separator with a filter wrench.

Caution: Be careful to prevent any contaminates or debris from entering the water separator when remove it for cleaning! Even though the water separator/pre-filter nipple has a protective wire screen, debris could jam the Gerotor and cause the fuse to blow. This is not a warranty item.

Dispose of waste fuel and used filters properly to protect OUR environment!

AirDog® Fuel Filter Pre-filter Nipple with

Wire Screen (1 1/8th Inch Hex)

Prefilter/Water SeparatorWith Drain Valve

Section 10 Fuel Filter & Pre-Filter

22


How to Remove and Re-install the Pressure Regulator!The Adjustable Pressure Regulator is made of all stainless steel components, except for the viton O’rings.

Regulator Components

A - Adjustor ScrewB - Jam NutC - Base NutD - SpringE - PlungerF - Plunger O’ring

Figure 52

STEP 1 STEP 2 STEP 3

STEP 4 STEP 5 STEP 6

Remove the Adjustor Assembly from the AirDog® base. Be careful to not damage the O’rings or lose the regulator spring or plunger.

Turn Adjustor Screw “A” Counter clockwise to remove the assembly.

Loosen Jam Nut “B” and regulator base nut “C”.

Re-adjust the output pressure by turning the Adjustor Screw counter clockwise until it stops against the Base Nut. Then, turn the Adjustor Screw in, clockwise 2.5 turns.

Tighten the Base Nut.Be sure the Regulator Plunger and Spring are properly positioned, then carefully insert the Adjustor Assembly into the base. Turn the assembly clockwise until the base nut is flush with the surface of the AirDog® base. NOTE: Units built after December 1, 2013 require 2.5

turns. Units built before December 1, 2013 require 5 turns

Section 11 Pressure Regulator

23

NOTES

24


Bulletin No. 206-1-0401 Revised February, 2017

Copyright© 2017CD Patents, LLC

All Rights Reserved

Date post:	28-Mar-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

INDUSTRIAL Fuel Air Separation Systemairdogdiesel.com/wp-content/uploads/2017/05/A3SPBT401...FUEL...

Documents