• DIN radio provision with pocket• ISO mount radio provision with pocket• Double DIN radio provision • Stacked ISO mount units provision• Texured and painted to match factory finish
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Snap In Pocket
Refer also to the instructions included with the aftermarket radio.
KNOWLEDGE IS POWEREnhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
Metra recommends MECPcertified technicians
99-7013TB DASH DISASSEMBLY
MITSUBISHI OUTLANDER 2007-UP
PASSENGERAIRBAG OFF
PASSENGER
PASSENGERAIRBAG OFF
PASSENGER
B
C
1
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
1
Unclip and remove the vents from theleft and right side of the factory radiopanel. (Figure A)
Remove (4) Phillips screws securingthe radio chassis. Unplug and removethe chassis. (Figure C)
2
Remove (2) Phillips screws securingthe radio trim panel then unclip andremove the panel. (Figure B)
3
4
A
Continued on page 2.
99-7013TB DASH DISASSEMBLY
MITSUBISHI OUTLANDER 2007-UP
2
Remove the labels from the front ofthe radio trim panel at each side ofthe hazard switch by pushing themout from behind the panel. (Retain thelabels to be reused during kit prepa-ration) (Figure F)
6
E
F
Continued to kit preparation.
REMOVE“9” PHILLIPS SCREWS (RETAIN SCREWS)
D
Remove (7) Phillips screws securingthe hazard switch assembly to theback of the factory radio trim panel.Unplug the ribbon cable from the hazard switch assembly and removeassembly from panel from rear.(Retain the screws and switchassembly to be reused during kitpreparation) (Figure D,E)
5
99-7013TB KIT PREPARATION
3
Secure the hazard switch panel into the radio housing using the factory hardwareremoved previously and apply labels from the front of the factory radio trim panel tofront of the Metra radio panel. (Figure A,B)
5
Continue to kit assembly.
A
PASSENGERAIRBAG OFF
PASSENGER
B
MITSUBISHI OUTLANDER 2007-UP
4
99-7013TB KIT ASSEMBLY
A
B
C
DIN RADIO PROVISION WITH POCKET
Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs outward. (Figure A)
1
Slide the aftermarket radio into thecage until it snaps into place. (Figure B)
2
Snap the pocket into the radio housing.(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
99-7013TB KIT ASSEMBLY
5
B
CD
ISO MOUNT RADIO PROVISION WITH POCKET
Mount the ISO Brackets to the after-market radio using the screws sup-plied with the radio. (Figure A)
1
Slide the radio into the Radio Housinguntil it snaps into place. (Figure B)
2
Snap the Trim Plate onto the front ofthe Radio Housing. (Figure C)
3
Snap the pocket into the RadioHousing. (Figure D)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
99-7013TB KIT ASSEMBLY
6
B
C
DOUBLE DIN/STACKED ISO UNITS PROVISION
Cut and remove the center bar fromthe Radio Housing. (Figure A)
1
Snap the Double DIN Brackets to theinside edge of the Radio Housing.(Figure B)
2
Slide the Double DIN or stacked ISOunit(s) into the bracket/radio housingassembly and secure the Double DINor stacked ISO unit(s) to the assemblyusing the screws supplied with theunit(s). (Figure C)
3
Snap the Double DIN Trim Plate ontothe front of the Radio Housing.(Figure C)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
A
7
99-7013TB FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individuallytape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
METRA / EIA WIRING CODE12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications.
Make wiring connections using the EIA color code chart shown below and the instructions included with the headunit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
