Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2015 American Honda Motor Co., Inc. – All Rights Re
VERSION 1
FOG LIGHTSP/N 08V31-T0A-100Dserved. AII02406-16 (150
2016 CR-V
9) 0
Issue Date
SEP 2015
PARTS LIST
Fog light harness
Switch harness
Relay
7 Wire ties
Wire tie with holder
6 Aluminum tapes
2 Self-tapping screws, 5 x 16 mm
20A Fuse
Fuse label
2 Spring nuts
Left fog light
Right fog light
Left trim
Right trim
Light switch
Ground bolt (Not used)
1 of 178V31-T0A-1000-9A
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Diagonal cutters
Ratchet
10 mm Socket
10 mm Open end wrench
Isopropyl alcohol
Shop towel
Tape
Masking tape
Blanket
Scissors
The following tool is available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.
• Trim Tool Set (T/N SOJATP2014)
Illustration of the Fog Lights Installed on the Vehicle
QD13104BX
RIGHT FOG LIGHT
LEFT FOG LIGHT
SWITCH HARNESS
20A FUSE
LIGHT SWITCH
FOG LIGHT HARNESS
2 of 17 AII02406-1
INSTALLATION
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
1. Disconnect the negative cable from the battery.
Removing the Vehicle Parts
2. Remove the driver’s dashboard panel and unplug the vehicle connector.
�0N2019BG
VEHICLE CONNECTOR
6 CLIPS
DRIVER’S DASHBOARD PANEL
6 (1509) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
3. Remove the driver’s dashboard under cover.
�0N2021BGPINDRIVER’S DASHBOARD UNDER COVER
KNOB(Turn.)
CLIP
4. Attach the masking tape to the upper column cover as shown.
�0N2023A G
MASKING TAPE
UPPER COLUMN COVER
STEERING WHEEL
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02406-1
5. Lower the tilt lever, and turn the steering wheel 90° counterclockwise.
�0N2024BG
PLASTIC TRIM TOOL
STEERING WHEEL
LOCK
UPPER COLUMN COVER
90°
6. Using a plastic trim tool, release the lock as shown.
7. Turn the steering wheel 180° clockwise. Using a plastic trim tool, release the lock as shown.
�0N2025BG
LOCK
UPPER COLUMN COVER
PLASTIC TRIM TOOL
180° Clockwise.
6 (1509) 3 of 17
8. Secure the upper column cover to the meter panel with the tape.
�0N2026A G
UPPER COLUMN COVER
TAPE
2 RETAINING TABS
METER PANEL
9. Remove the two self-tapping screws from the lower column cover.
�0N2027A G
LOWER COLUMN COVER
2 SELF-TAPPING SCREWS
4 of 17 AII02406-1
10. Remove the lower column cover (one self-tapping screw).
QD32703AA
SELF-TAP-PING SCREW
LOWER COLUMN COVER
11. Remove the driver’s front door sill trim.
�0D2801AD
2 RETAINING TABS
3 CLIPS
2 HOOKS
DRIVER’S FRONT DOOR SILL TRIM
6 (1509) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
12. Pull away the door opening seal, and remove the driver’s kick panel.
�0N2030A G
DOOR OPENING SEAL(Pull away.)
DRIVER’S KICK PANEL
2 CLIPS
13. Remove the two self-tapping screws and the three clips from the left front wheel arch protector.
QD12801AX
3 CLIPS
LEFT FRONT WHEEL ARCH PROTECTOR
2 SELF-TAPPING SCREWS
FRONT
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02406-1
14. Remove the left front wheel arch protector.
QD12802AXFRONT
6 CLIPS
LEFT FRONT WHEEL ARCH PROTECTOR
3 RETAINING TABS
2 CLIPS
15. Repeat steps 13 through 14 on the right side of the vehicle.
16. Attach the tapes to the front bumper, left headlight, and left front fender as shown.
QD12803BX
TAPES
FRONT FENDER
LEFT HEADLIGHT
RIGHT HEADLIGHT
17. Repeat the same procedure on the right side of the vehicle.
6 (1509) 5 of 17
18. Remove the four clips from the front grille.
QD12804BX
4 CLIPS
FRONT GRILLE
19. Remove the front bumper.
• Remove the two self-tapping screws, two bolts, and six clips.
QD12805BX
2 SELF-TAPPING SCREWS
FRONT BUMPER
6 CLIPS
2 BOLTS
6 of 17 AII02406-1
• On each side, release the three retaining tabs.
QD12806BXFRONT BUMPER
3 RETAINING TABS
• On each side, release the four retaining tabs.
QD12807BXFRONT BUMPER
4 RETAINING TABS
6 (1509) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
• Release the four clips and two retaining tabs.
• With the help of an assistant, remove the front bumper.
• Place the front bumper on a blanket after removal.
QD12808CX
FRONT BUMPER
2 RETAINING TABS
FRONT GRILLE
4 CLIPS
20. Remove the four clips from the left front inner fender, and release the left front inner fender. NOTE: Do not fully remove the left front inner fender.
QD12809AX
FRONT
4 CLIPS
LEFT FRONT INNER FENDER
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02406-1
Installing the Fog Light
21. Remove the left cover by releasing the tabs.
QD12901AX
LEFT COVER
8 RETAINING TABS
CLIP
FRONT BUMPER
2 RETAINING TABS
22. Install the spring nut to the front bumper.
QD12902AX
SPRING NUT
FRONT BUMPER
6 (1509) 7 of 17
23. Install the left fog light to the front bumper with two hooks and one self-tapping screw. Hook the two hooks in the order shown.
QD12903AX
FRONT BUMPER
1
SELF-TAPPING SCREW
HOOK 2 HOOK
HOOK LEFT FOG LIGHT2
HOOK1
8 of 17 AII02406-1
24. Install the left trim to the front bumper with one clip and ten retaining tabs.
QD12904AXLEFT TRIM
8 RETAINING TABS
CLIP
FRONT BUMPER
2 RETAINING TABS
25. Repeat steps 21 through 24 on the right side of the front bumper.
Routing the Fog Light Harness
26. Plug the fog light harness 1-pin connector to the vehicle 1-pin connector.
QD12905AX
FRONT
FOG LIGHT HARNESS 1-PIN CONNECTOR
VEHICLE 1-PIN CONNECTOR
FOG LIGHT HARNESS
VEHICLE HARNESS
LEFT FRONT INNER FENDER
6 (1509) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
27. Secure the fog light harness to the vehicle harness with two wire ties.
QD12906BX
FRONT
VEHICLE PANEL
FOG LIGHT HARNESS GROUND TERMINAL
ALUMINUM TAPE
FRONT VIEW
2 WIRE TIES
FOG LIGHT HARNESS
Align.
VEHICLE GROUND BOLT
ALUMINUM TAPE
VEHICLE GROUND TERMINALS
VEHICLE PANEL(Clean with isopropyl alcohol.)
28. Remove the vehicle ground bolt, and secure the fog light harness ground terminal to the vehicle ground terminals with the vehicle ground bolt just removed.
29. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the aluminum tape will attach. Secure the fog light harness to the vehicle panel with one aluminum tape.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02406-1
30. Route the fog light harness under the left headlight, and secure one clip on the fog light harness to the bumper beam.
QD13001AX
LEFT HEADLIGHT
VEHICLE HARNESS 2 WIRE
TIES
CLIPFRONT FOG LIGHT
HARNESS
VEHICLE HARNESSBUMPER
BEAM
31. Secure the fog light harness to the vehicle harness with two wire ties.
32. Route the fog light harness along the bumper beam, and secure the clip on the fog light harness to the bumper beam as shown.
QD13002AX
CLIP
FRONT
FOG LIGHT HARNESS
BUMPER BEAMFOG LIGHT
HARNESS
BUMPER BEAM
6 (1509) 9 of 17
33. Using isopropyl alcohol on a shop towel, thoroughly clean the areas where the aluminum tapes will attach. Secure the fog light harness to the bumper beam with three aluminum tapes.
QD13003BX
3 ALUMINUM TAPES
BUMPER BEAM(Clean with isopropyl alcohol.)
FOG LIGHT HARNESS
ALUMINUM TAPE(Cut in half.)
34. Using scissors, cut one aluminum tape in half. Secure the fog light harness to the bumper beam with two pieces of halved aluminum tape.
10 of 17 AII02406-1
35. Route the fog light harness, and secure one clip on the fog light harness to the vehicle panel.
QD13004BX
VEHICLE HARNESS
WIRE TIE FRONT
CLIPVEHICLE PANEL
FOG LIGHT HARNESS
ALUMINUM TAPE
VEHICLE PANEL(Clean with isopropyl alcohol.)
36. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the aluminum tape will attach. Secure the fog light harness to the vehicle panel with one aluminum tape.
37. Secure the fog light harness to the vehicle harness with one wire tie.
38. Reinstall the left front inner fender.
6 (1509) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
39. With the help of an assistant, bring the front bumper close to the vehicle. Plug the two fog light harness 2-pin connectors to the left fog light and right fog light, and reinstall the front bumper.
QD13005BX
2-PIN CONNECTOR
FRONT BUMPER
FOG LIGHT HARNESS
LEFT FOG LIGHT
RIGHT FOG LIGHT
2-PIN CONNECTOR
Routing the Switch Harness
40. Install the relay into the switch harness relay block.
�0D1404AB
RELAY
RELAY BLOCK
SWITCH HARNESS
WIRE TIE WITH HOLDER
41. Install the one wire tie with holder into the switch harness relay block.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02406-1
42. Secure the switch harness relay block to the vehicle harness with the wire tie with holder on the switch harness relay block.
QD40407AA
RELAY BLOCK
SWITCH HARNESS
WIRE TIE WITH HOLDER
VEHICLE CLIP
VEHICLE HARNESS
FUSE BOX
43. Plug the switch harness 1-pin connector to the vehicle 1-pin connector.
QD40701BA
VEHICLE 1-PIN CONNECTOR
SWITCH HARNESS 1-PIN CONNECTOR
FUSE BOX
6 (1509) 11 of 17
If the vehicle is equipped with the other accessory harness 4-pin connector, go to step 46; otherwise, continue with step 44.
Without other accessory harness 4-pin connector
44. Route the switch harness along the vehicle harness.
QD40702BA
SWITCH HARNESS 4-PIN CONNECTOR
FUSE BOX
FRONT VIEW
SWITCH HARNESS
Plug in here.
FUSE BOX
45. Plug the switch harness 4-pin connector to the fuse box. Go to step 48.
12 of 17 AII02406-1
With other accessory harness 4-pin connector
46. Route the switch harness along the vehicle harness.
QD52801AA
SWITCH HARNESS 4-PIN CONNECTOR
OTHER ACCESSORY HARNESS 4-PIN CONNECTOR
SWITCH HARNESS
FUSE BOX
OTHER ACCESSORY HARNESS
47. Plug the switch harness 4-pin connector to the other accessory harness 4-pin connector.
6 (1509) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
If the vehicle is equipped with the other accessory harness 6-pin connector, go to step 49; otherwise, continue with step 48.
Without other accessory harness 6-pin connector
48. Plug the switch harness 6-pin connector to the fuse box. Go to step 51.
QD40703BASWITCH HARNESS 6-PIN CONNECTOR
FUSE BOX
Plug in here.
FUSE BOX
FRONT VIEW
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02406-1
With other accessory harness 6-pin connector
49. Remove the dummy connector from the other accessory harness 6-pin connector.
QD40704AA
SWITCH HARNESS 6-PIN CONNECTOR
FUSE BOX
DUMMY CONNECTOR(Discard.)
OTHER ACCESSORY HARNESS 6-PIN CONNECTOR
50. Plug the switch harness 6-pin connector to the other accessory harness 6-pin connector.
51. Secure the switch harness to the vehicle harness with two wire ties.
QD40705BA
VEHICLE HARNESS
SWITCH HARNESS
FUSE BOX
2 WIRE TIES
6 (1509) 13 of 17
52. Unplug the vehicle connector from the light switch.
QD61101AG
LIGHT SWITCH
STEERING COLUMN
2 RETAINING TABS
LEVER
VEHICLE CONNECTOR
STEERING WHEEL
Do not pull on the lever.
NO
53. Push in on the two retaining tabs, slide the light switch out, and remove it from the steering column. Do not pull on the lever.
14 of 17 AII02406-1
54. Install the new light switch to the steering column. Make sure both retaining tabs are locked in place. Do not push on the lever.
QD61102AG
STEERING COLUMN
LEVER
VEHICLE CONNECTOR
STEERING WHEEL
NEW LIGHT SWITCH
NO
Do not push on the lever.
55. Plug the vehicle connector to the new light switch. Make sure the vehicle harness is not being stretched.
6 (1509) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
56. If a 20A fuse is already installed in the fuse box, go to step 58, otherwise, plug the 20A fuse into the fuse box.
QD40706BA
FUSE BOX
Plug in here.
FUSE BOX
FRONT VIEW
20A FUSE
57. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the fuse label will attach. Attach the fuse label to the fuse seal on the driver’s dashboard under cover.
�0D1510AB
FUSE SEAL
FRONT VIEW
DRIVER’S DASH-BOARD UNDER COVER
FUSE SEAL(Clean with isopropyl alcohol.)
ATTACHING
FUSE LABEL(OPTION FUSE 20A)
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02406-1
58. Remove the relay box upper cover (two retaining tabs).
�A53004AE
RELAY BOX UPPER COVER
2 RETAINING TABS
FRONT
LEFT HEADLIGHT
59. Using isopropyl alcohol on a shop towel, thoroughly clean the area where the fuse label will attach. Attach the fuse label to the relay box upper cover.
�A60101BE
FUSE LABELRELAY BOX UPPER COVER(inside)
FUSE LABELATTACHING POINT(Clean with isopropyl alcohol.)
RELAY BOX UPPER COVER
6 (1509) 15 of 17
60. Check that all wire harnesses are routed properly and all connectors are plugged in.
61. Reinstall all removed parts.
62. Reconnect the negative cable to the battery.
63. Press and hold the radio power button for two seconds to restore the radio and navi (if equipped) system functions.
64. Reset the clock on vehicle without navigation.
USE AND CARE
Check the Operation of the Fog Lights
65. Turn the headlight switch to the “ ” position (headlights on low beam).
66. Turn on the fog light switch (indicator is on).
67. If the fog lights do not turn on, check the fuse and all the connectors, including the ground cable.
053101AB
FO
G L
IGH
T
SW
ITC
H
HEADLIGHT SWITCH
Low HighOFF
ON
OFF - - - -
- - -ON
NOTE: The fog light lenses may cloud when the outside temperature is cold; this is normal and should go away in warm weather.
16 of 17 AII02406-1
How to Aim the Fog Lights
68. Adjust the fog light:
• To adjust, turn the aiming adjustment screw in or out until the correct aiming is obtained.
• Adjust the aiming according to local laws and regulations.
QD13006AX
LEFT FOG LIGHT
To raise.To lower.
FRONT BUMPER
LEFT TRIM
6 (1509) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
BULB REPLACEMENT
1. Release the splash shield (one bolt and one clip).
QD13101AXCLIP
SPLASH SHIELD BOLT
2. Insert your hand inside of the splash shield released in step 1. Unplug the connector from the fog light.
QD13102AX
FOG LIGHT BULB
CONNECTOR
3. Remove the bulb.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII02406-1
4. Install the new bulb to the fog light.
• Use only a Genuine Honda halogen light bulb of specified wattage.
Rating: 12V 35W H8 Halogen Light Bulb P/N 33165-TL0-003
• Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution.
• When installing the new bulb, align the cutout on the fog light with the tab on the new bulb and turn the new bulb in completely. If not properly aligned, the fog light may annoy oncoming driver’s.
QD13103AX
NEW BULBTurn.
FOG LIGHT
CONNECTOR
NEW BULB
5. Reinstall the removed parts. Check that the wire harnesses are not pinched. Be sure to tighten the clip and bolts securely.
6. Check the operation of the fog light; adjust the aiming if necessary.
6 (1509) 17 of 17