Installation Guide - Digilock · Standard Body Keypad Standard Body RFID Vertical Body Keypad...

Installation GuideKeypad & RFID

Standard, Vertical, & Horizontal Body

Shared & Assigned Use

Before Lock Installation 3

Door Preparation 16Strike Plate Installation 16

Required Components 16Installation 17

Door Mounting Holes Drill Instructions and Templates 18Drill Instructions 18Template for Standard & Vertical Body 19Template for Horizontal Body 20

Routing Instructions and Template 21Routing Instructions 21Routing Template for Standard Body 22Routing Template for Horizontal Body 23Routing Template for Vertical Body 24

Metal Door Preparation 25Compatibility Guide 25Removal of 3-hole Lock Plug 26Removal of Padlock Hasp 27

Recess Mount Installation 10For door thickness measuring between .370” - .850” (9.4mm - 21.6mm) 10

For door thickness measuring between .850” - 2.368” (21.6mm - 60.1mm) 13

Required Components 10


Installation 11

Installation 14

Surface Mount Installation 4For door thickness measuring between .01” - .480” (0.01mm - 12mm) 4

For door thickness measuring between .480” - 1.998” (12.2mm -50.7mm) 7



Installation 5

Installation 8

Before Lock Installation

The door must be prepared for lock installation.

Strike Plate

Angled Strike Plate Security Strike Plate Double Door Strike Plate

For recess mount installations, the door must be routed and have door mounting holes.

For Standard Body For Vertical Body For Horizontal Body

Routed Door with Door Mounting Holes

Door Mounting Holes For surface mount installations, the door must have door mounting holes.

For Standard & Vertical Body For Horizontal Body

3

A strike plate must be installed. 1.

2a.

2b.

Surface Mount InstallationFor door thickness measuring between .01” - .480” (0.01mm - 12.0mm)

u Do not use an electric screw gun unless it is equipped with a torque adjuster and is set to low.

1 - Front Unit

Standard Body Keypad Vertical Body KeypadStandard Body RFID Vertical Body RFID Horizontal Body Keypad

Springbolt Springlatch Deadbolt Deadlatch

1 - Rear Unit

*Not included

1 - Plastic Ring 1 - Locking Nuts

1* - Ratchet/Screw Gun with a 3/8” Socket

*Required for door thickness measuring between .315”-.480” (8.0-12.2mm)

1* - Pin Extender

Required Components

4

InstallationFor illustration, a standard body, keypad lock with a bolt rear unit is used.

Place the plastic ring on the front unit. If required, connect the pin extender to the rear unit.

Make sure the connector pins align properly with the connector. If properly connected, a triple beep will be heard and the LED will flash three times.

Insert the locking nuts on the screw posts and tighten using the ratchet/screw gun. u Do not over tighten.

Hold the front unit against the front of the door. Use the rear unit mounting holes as a guide, then slide the front and rear units together.

Insert the front unit screw posts through the door mounting holes.

5

1 2

3

5

4

6

To test keypad locks: Press = ` To test RFID locks: Press `

Test the locks while the door is open. If locks do not operate, remove and reinstall.Close the door and test again. If 10 rapid beeps are heard and the LED flashes 10 times, the strike plate and/or the door needs to be adjusted as it is preventing the lock from operating.

6

7

For door thickness measuring between .480” - 1.998” (12.2mm - 50.7mm)

Required Components


1 - Plastic Ring 2 - Phillips Head Screws

1* - Pin Extender

2 - Split Lock Washers 1* - Phillips Head Screwdriver (#2)

1 - Front Unit


Springbolt Springlatch Deadbolt Deadlatch

1 - Rear Unit

*Two (2) pin extenders are required for door thickness measuring between 1.20”-1.998” (30.5-50.7mm)

7

*Not included

Installation

Place the plastic ring on the front unit.

Insert the front unit nut posts through the door mounting holes.

Place the split lock washers on the phillips head screws and insert them through the rear unit mounting holes.


Hold the front unit against the front of the door. Use the screws of the rear unit as a guide then slide the front and rear units together.

For illustration, a standard body, keypad lock with a bolt rear unit is used.

8

Connect the pin extender to the rear unit.

1

3

2

5

4

6

Tighten the screws using the phillips head screw driver.


Test the locks while the door is open. If locks do not operate, remove and reinstall.

9

Close the door and test again. If 10 rapid beeps are heard and the LED flashes 10 times, the strike plate and/or the door needs to be adjusted as it is preventing the lock from operating.

7

8

Recess Mount InstallationFor door thickness measuring between .370” - .850” (9.4mm - 21.6mm)

Required Components


2 - Locking Nuts1* - Ratchet/Screw Gun with a 3/8” Socket1* - Pin Extender

1 - Front Unit


Solenoid Spring Bolt Solenoid Spring Latch Motorized Dead Bolt Motorized Dead Latch

1 - Rear Unit

*Required for door thickness measuring between .685”-.850” (17.4-21.6mm)

10

*Not included

InstallationFor illustration, a standard body, keypad lock with a bolt rear unit is used.

Insert the locking nuts on the screw posts and tighten using the ratchet/screw gun.u Do not over tighten.



If required, connect the pin extender to the rear unit. Insert the front unit screw posts through the door mounting holes.

11

1

3

2

5

4



12


6

For door thickness measuring between .850” - 2.368” (21.6mm - 60.1mm)

Required Components


1* - Phillips Head Screwdriver (#2) 1* - Pin Extender

2 - Phillips Head Screws 2 - Split Lock Washers

1 - Front Unit


Solenoid Spring Bolt Solenoid Spring Latch Motorized Dead Bolt Motorized Dead Latch

1 - Rear Unit

*Two (2) pin extenders are required for door thickness measuring between 1.570”-2.368” (39.9-60.1mm)

13

*Not included

Tighten the screws using the phillips head screw driver. Do not over tighten.

Installation

For illustration, a standard body, keypad lock with a bolt rear unit is used.


Insert the front unit nut posts through the door mounting holes.


Connect the pin extender to the rear unit. Place the split lock washers on the phillips head screws and insert them through the rear unit mounting holes.

14

1

3

2

5

4

6



15


7

Door Preparation

Strike Plate InstallationRequired Components

Do not use an electric screw gun unless it is equipped with a torque adjuster and is set to low.

1* - Phillips Head Screwdriver (#1)

Strike Plate

1. A strike plate must be installed.

Angled Strike Plate Security Strike Plate Double Door Strike Plate

16

*Not included

Installation

17

Position the strike plate on the door frame centering it with the center of the desired location of the door mounting holes.

Doo

r Fra

me

Drill 0.25” (6.35mm) pilot holes using a 1/6” drill bit.

Doo

r Fra

me

Drill PilotHoles Here

Adjust the strike plate to the proper position (.125” (3.18mm) from the door edge) then tighten the self tapping screws.

Doo

r Fra

me

0.125 in

(3.18 mm)

Allow .125” (3.18mm) from door edge and mark the position of the adjustment slot holes.

Doo

r Fra

me

0.125 in

(3.18 mm)

Mark Here

Position the strike plate and the self tapping screws into the adjustment slot holes. Do not tighten the screws.

Doo

r Fra

me

Position and tighten the remaining self tapping screw into the center hole.

Doo

r Fra

me

1

3

2

5

4

6

Door Mounting Holes Drill Instructions and Templates

Drill InstructionsFor illustration, the mounting holes template for standard & vertical body locks is used.

Place the template on the front of the door.Align the edge of the door with the mark on the template, and then align the center line of the template with the mark on the door. Secure the template with removable tape.

TemplateCenter line

StrikePlate

Center

Edge of Strike Plate

Strike Edge Marker

MarkTemplate

Mark Door Edge

Door Edge

DrawnMarker

Drill x25/16” 0.3125 in

(7.94 mm)

Drill 3/4” - 0.75 in(19.1 mm)

Mark the center point of the three door mounting drill holes on the front of the door.Use the drill bits specified on the template to drill appropriately sized door mounting holes.

TemplateCenter line

StrikePlate

Center


Strike Edge Marker

MarkTemplate

Mark Door Edge

Door Edge

DrawnMarker

Drill x25/16” 0.3125 in

(7.94 mm)

Drill 3/4” - 0.75 in(19.1 mm)

Align both the center line and strike plate edge of the installed strike plate. Hold the template in place and close the door.

TemplateCenter line

StrikePlate

Center


Strike Edge Marker

MarkTemplate

Mark Door Edge

Door Edge

DrawnMarker

Drill x25/16” 0.3125 in

(7.94 mm)

Drill 3/4” - 0.75 in(19.1 mm)

Mark the edge of the door on the template. Mark the center line of the template on the edge of the door.

TemplateCenter line

StrikePlate

Center


Strike Edge Marker

MarkTemplate

Mark Door Edge

Door Edge

DrawnMarker

Drill x25/16” 0.3125 in

(7.94 mm)

Drill 3/4” - 0.75 in(19.1 mm)

18

1

3

2

4

Template for Standard & Vertical Body

Templates may not print to scale. Check all measurements before proceeding.Before printing, turn off auto scaling in printer setup and print at 100%.

All measurements in thousandths of an inch and millimeters

.3007.62 (mm)

use 5/16" bit

.90523 (mm)

.90523 (mm).300

7.62 (mm)

.75019.05 (mm) use 3/4" bit

001.1)

mm( 9.72

001.1)

mm( 9.72

001.

1)

mm(

9.72

001.

1)

mm(

9.72

ALIGN EDGE OFSTRIKE PLATE HERE

FOR LEFTCLOSING DOOR

ALIGN EDGE OFSTRIKE PLATE HEREFOR RIGHTCLOSING DOOR


FOR LEFTCLOSING DOOR

ALIGN EDGE OFSTRIKE PLATE HEREFOR RIGHTCLOSING DOOR

CENTER LINE

CENTER LINE

19

Template for Horizontal Body

All m

easurements in thousandths

of an inch and millim

eters

.3007.62 (m

m)

use 5/16" bit

.90523 (m

m)

.90523 (m

m)

.3007.62 (m

m)

.75019.05 (m

m)

use 3/4" bit

001.1)mm( 9.72

001.1)mm( 9.72

001.1)mm( 9.72

001.1)mm(9.72


FOR TOPCLOSING DRAWER


FOR TOPCLOSING DRAWER


FOR BOTTOMCLOSING DRAWER


FOR BOTTOMCLOSING DRAWER

CENTER LINE

CENTER LINE


20

Routing Instructions and Template

Routing Instructions

2. Drill the appropriate door mounting holes. Refer to the door mounting holes drill instructions and template.

1. Choose the appropriate routing template (standard, vertical, or horizontal).

3. Align the mounting holes drawn on the template with the mounting holes drilled on the door.

4. Route the door according to the measurements shown on the template.

21

Routing Template for Standard Body

2.01 in (51 mm)1.98 in (50 mm)

2.19 in(56 mm)

.300 (8mm)2x

0.400/0.425 in DEEP(10/11 mm)

.75 (19mm)

R 0.125(3mm)4x

2.72 in (69 mm)2.68 in (68 mm)


22

Routing Template for Horizontal Body

1.25” (32mm)1.23” (31mm)

2.185” (56mm)

0.30”(8mm)

2x .400/.425 DEEP(10/11mm)

0.75” (19mm)

R 0.125”(3mm)

4x

3.80” (97mm)3.78” (96mm)

23


Routing Template for Vertical Body

1.25” (32mm)1.23” (31mm)

2.185” (56mm)

0.30”(8mm)2x

.400/.425 DEEP(10/11mm)

0.75”(19mm)

R 0.125”(3mm)4x

3.80” (97mm)3.78” (96mm)


24

Metal Door Preparation

Compatibility GuideDigilock is compatible with a majority of 3-hole configuration, latch, and handle door types. Some doors may require modification to clear obstructions.

Single Point Latch

Handle

Standard Lift

Recessed Cup with Single Point Latch

Recessed Cup with Multi-point Latch

Box Locker Padlock Hasp

25

Exam

ple 1

Exam

ple 2

Removal of 3-hole Lock Plug

Remove any obstructions to the door mounting holes.

Rear View of Locker Door

with Lock Plug

Front View of Locker Door

with Lock Plug

Rear View of Locker Door

with Lock Plug

Front View of Locker Door

with Lock Plug

26

The padlock hasp must be removed

Removal of Padlock HaspEx

ample

1Ex

ample

2

Close the door and mark the area to cut the padlock hasp.

Open the door then cut the padlock hasp on the marked cut-line.

Smooth out rough or sharp edges.

Close the door and make sure that nothing is protruding above the surface of the door.

1 - Metal File1 - Handheld Grinder or Hack Saw

Phone: 707 766 6000www.digilock.com | [email protected]

IG-XXXX-XX-DEN071114 27

Date post:	22-Aug-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

Installation Guide - Digilock · Standard Body Keypad Standard Body RFID Vertical Body Keypad...

Documents