IntelliCon®- CAC · IntelliCon®-CHS is a microprocessor-based, fuel-saving control for commercial...

Commercial Air Conditioning Electrical Consumption Economizer

Intellidyne’s IntelliCon®-CAC typically reduces Commercial

Air Conditioning electric consumption by 10% to 20% or

more. The IntelliCon-CAC is a microprocessor-based, UL

listed, electronic control that uses intelligent Dynamic Cycle

Management (DCM) technology to automatically adjust the

compressor cycles to achieve the greatest efficiency and

reduced electrical usage, while assuring consistent temperature

levels. IntelliCon-CAC is maintenance free, easy to install by

a qualified installer, and is guaranteed to save energy.

Features

• Dynamic Cycle Management (DCM)

technology reduces air conditioning

electric consumption—typically 10%

to 20%

• UL listed, “Energy Management

Equipment”

• Increased savings without replacing

or upgrading costly system

components

• State-of-the-art microprocessor-

based control—Illuminated LCD

display shows run time hours,

economizing hours, operating

modes and system diagnostics

• For systems 5 tons or larger

• Protects compressor against

momentary power outages and

short cycling

• Simple installation by a qualified

HVAC/R installer

• No programming or follow-up visits

required

• Maximum year-round efficiency

• Reduces maintenance and extends

compressor life

• Fail-safe operation

• Guaranteed to save energy

• 15-year replacement warranty for

breakdowns or defects

IntelliCon ®- CAC

A smart way to save on yourcommercial air conditioning costs.

ntellidyne’s InteellliCCon® CAC typically reduces Commercial

Specifi cations

Mounting:

In any position via molded-in 1/2”

Electrical Fitting

Size:

4”H x 4”W x 2”D

Operating Humidity:

5% - 95% Non-Condensing

Operating Temperature Range:

-10°F - +120°F

Power Input:

24/115/220 VAC @ 5W

Control Circuit:

24 VAC/DC, 115/220 VAC

Relay Contact:

10A @ 220VAC General Purpose

UL Listed,

“Energy Management Equipment”

Made in U.S.A.

Sizing of air conditioning systems is based upon a number of factors. When

any of the design considerations are not met, the air conditioning system

can become relatively oversized for the cooling load and thus less efficient.

Intellidyne’s patented process uses Dynamic Cycle Management (DCM)

technology to determine the “cooling demand” and “thermal characteristics”

of the entire air conditioning system by analyzing the compressor’s “cycle

pattern,” and dynamically modifies that “cycle pattern” to provide the

required amount of cooling in the most efficient manner. This is accomplished

in “real-time” by delaying the start of the next compressor “on” cycle by

an amount determined by the “cooling demand” analysis. These new

patterns also result in less frequent and more efficient compressor cycles.

IntelliCon®-CAC electrically augments the existing controls, and will not

cause the compressor to run unless the existing thermostat is calling for

it to do so. Just as computer control has increased the gas mileage of

automobiles, IntelliCon-CAC improves the electrical efficiency of air

conditioning systems, by supplementing the antiquated on/off action of the

thermostat (even a “smart” one) with the analysis and control capabilities

of a computer.

Field-testing has demonstrated that IntelliCon’s “intelligent modification of

compressor cycling” with DCM Technology will lead to significant electrical

energy savings. IntelliCon’s innovative and intelligent algorithms have

proven electrical savings; not only on properly sized and operating

systems, but also on units that were undersized or those that had

not been properly maintained.

IntelliCon-CAC works in conjunction with the existing thermostat and

will not void the compressor manufacturer’s warranty. An additional

feature of the IntelliCon-CAC is the accepted industry practice of

compressor anti-short-cycling control.

Installation by a qualified HVAC/R service technician is recommended.

IntelliCon-CAC does not require any programming, adjustments, or

maintenance.

Commercial Air Conditioning Electrical Consumption Economizer

IntelliCon ®- CAC

©2009 Intellidyne and the IntelliCon logo are registered trademarks of Intellidyne LLC. The Energy Star logo is a registered trademark courtesy of Energy Star Corporation. All rights reserved.

303 Sunnyside Boulevard, Suite 75, Plainview, NY 11803-1508, USA

Telephone: (516) 676-0777 • Toll Free: (866) 216-0777 • Fax: (516) 676-2640

www.intellidynellc.com

200906

Commercial Steam Heating System Fuel Economizer

IntelliCon®-CHS is a microprocessor-based, fuel-

saving control for commercial steam heating systems.

IntelliCon-CHS reduces: fuel consumption, wear on parts,

flue emissions and electrical usage when installed on any

new or existing gas or oil burner. IntelliCon-CHS uses

intelligent Dynamic Cycle Management (DCM) technology

to save energy by adjusting the burner run pattern to

match the system’s “heat load.”

IntelliCon ®- CHS (HP)

A smart way to save on your commercial steam heating costs.

Features

• For systems with ratings above

2.5 million BTU

• CHS for systems with operating

pressures > 2 psi and < 30 psi

• CHS-HP for systems with operating

pressures > 30 psi and < 145 psi

• Illuminated LCD display shows fuel

consumption savings, operating

modes, system diagnostics and

operating temperatures


technology reduces fuel consumption—

average savings 14.2%

• Short payback period—less than 18

months


Equipment”

• Increased savings without replacing or

upgrading costly system components

• “State-of-the-art” microprocessor-

based control

• Easily installed plug-in sensor(s)

(includes 1 required sensor)

• Simple installation by qualified

heating professional


• Easily programed for maximum savings


boiler life

• Guaranteed to reduce fuel

consumption by 10%

• 15 year limited warranty against


IntelliCon®-CHHSHS is a microprocessor-based fuel-


Specifi cations

Mounting:

On Vertical Surface via 3-point

Mounting System

Size:

7 1/2”H x 9 1/2”W x 4”D

Operating Humidity:



-10°F - +120°F

Power Input:

24/115/220 VAC @ 5W

Control Circuit:

24 VAC/DC, 115/220 VAC

Relay Contact:


UL Listed,


Made in U.S.A.




200902

Any heating system must be able to provide acceptable comfort at the

lowest anticipated outdoor temperature. In the U.S. and abroad, most

commercial boilers have a heat capacity between 1.5 to 2 times larger than

that needed to maintain the facility’s temperature on those extreme days.

Due to this over-sizing of the boiler, the burner will cycle on and off

continuously to maintain the desired steam pressure.

Using our patented Dynamic Cycle Management (DCM) Technology,

IntelliCon®-CHS increases “system efficiency.” Thus, the heating system

uses less fuel to generate the required amount of heat. This is done by

dynamically changing the pressure-controller’s effective dead-band based

upon the measured “heating load.” This causes the average steam pressure

to be varied (depending upon the measured load), and is accomplished

by extending the burner’s “off-time.” Extending the “off-time” also results in

longer, more efficient burn cycles and reduces burner on/off time. Just

as computer control has increased the gas mileage of automobiles,

IntelliCon-CHS with DCM Technology improves the fuel utilization of

heating systems, by supplementing the antiquated on/off control action

of the pressure-controller with the analysis and control capabilities of

a microprocessor.

Facility engineers will appreciate the LCD, which displays useful information

relative to the unit’s status, steam pressure fuel savings and system runtime,

which can be useful for system diagnostics and maintenance.

IntelliCon-CHS typically reduces fuel consumption 10% to 20% and

decreases burner cycling by 30% or more. Installation is simple for a

qualified heating technician. Programming is easily accomplished during

installation to maximize the fuel savings of the specific system.

Commercial Steam Heating System Fuel Economizer

IntelliCon ®- CHS (HP)

Light Commercial Steam Heating System Fuel Economizer

IntelliCon®-LCS is a microprocessor-based, fuel-saving

control for light-commercial steam heating systems.

IntelliCon-LCS reduces fuel consumption, wear on parts, flue

emissions and electrical usage, when installed on any new

or existing gas or oil burner. IntelliCon-LCS uses intelligent

Dynamic Cycle Management (DCM) Technology to save

energy by adjusting the burner run pattern to match the system’s

“heat load.” Its action is similar to the industry-accepted

method of “outdoor-air temperature reset control,” but does

not require an outdoor-air temperature sensor or the need

to profile the building in order to adjust the “reset” control

properly. IntelliCon-LCS determines the “heat load” by using

an easily installed pressure sensor that monitors the boiler’s

steam-pressure and the rate that this pressure is changing.

Features

• For commercial systems rated up to

2.5 million BTU

• Dynamic Cycle Management

(DCM) Technology reduces fuel

consumption—typically 10% to 20%






Equipment”



components


based control




installer

• Easily programmed for maximum

savings



boiler life





IntelliCon ®- LCS

A smart way to save on yourcommercial heating costs.

on® LCS is a micrroopprocessor based fuel savingS

Specifi cations

Mounting:

In any position via molded-on 1/2”

Electrical Fitting

Size:

4”H x 4”W x 2 1/2”D

Operating Humidity:



-10°F - +120°F

Power Input:

24/115/220 VAC @ 5W

Control Circuit:

24 VAC/DC, 115/220 VAC

Relay Contact:


UL Listed,


Made in U.S.A.


lowest anticipated outdoor temperature. In the U.S. and abroad, most light



Due to this over-sizing of the boiler, the burner will cycle on and off

continuously to maintain the desired steam pressure.

Using our intelligent Dynamic Cycle Management (DCM) Technology,

IntelliCon®-LCS increases “system efficiency.” Thus, the heating system

uses less fuel to generate the required amount of heat. This is done by

dynamically changing the pressure-controller’s effective dead-band based

upon the measured “heating load.” This causes the average steam pressure

to be varied (depending upon the measured load), and is accomplished by

extending the burner’s “off-time.” Extending the “off-time” also results in

longer, more efficient burn cycles and reduces burner on/off time. Just

as computer control has increased the gas mileage of automobiles,

IntelliCon-LCS with DCM Technology improves the fuel utilization of heating

systems, by supplementing the antiquated on/off control action of the

pressure-controller with the analysis and control capabilities of a computer.

Service personnel will appreciate the LCD readout, which displays useful

information relative to the unit’s status, steam pressure and domestic

hot-water temperature (if the optional sensor is installed), which can be

useful for system diagnostics and maintenance.

IntelliCon-LCS typically reduces fuel consumption 10% to 20%

and decreases burner cycling by 30% or more. Initial installation

programming is easily done by a qualified service technician by

following the on screen directions. After installation, IntelliCon-LCS

requires no maintenance.

Light Commercial Steam Heating System Fuel Economizer

IntelliCon ®- LCS





200902

Commercial Hot Water Heating System Fuel Economizer

IntelliCon®-CHW is a microprocessor-based fuel-saving

control for commercial hot-water heating systems.

IntelliCon-CHW reduces: fuel consumption, wear on parts,

flue emissions and electrical usage, when installed on any

new or existing gas or oil burner. IntelliCon-CHW uses

intelligent Dynamic Cycle Management (DCM) technology

to save energy by adjusting the burner run pattern to

match the system’s “heat load.”

Features

• For systems with ratings above

2.5 million BTU






technology reduces fuel consumption—

average savings 15.6%

• Short payback period—less than

18 months


Equipment”



components


based control




heating professional


• Easily programed for maximum

savings


boiler life

• Guaranteed to reduce fuel

consumption by 10%

• 15 year limited warranty against


IntelliCon ®- CHW

A smart way to save on your commercial hot water heating costs.

IntelliCon®-CHHHWW is a microprocessor-based fuel-savingW

Specifi cations

Mounting:

On Vertical Surface via 3-point

Mounting System

Size:

7 1/2"H x 9 1/2"W x 4"D

Operating Humidity:



-10°F - +120°F

Power Input:

24/115/220 VAC @ 5W

Control Circuit:

24 VAC/DC, 115/220 VAC

Relay Contact:


UL Listed,


Made in U.S.A.

A heating system must be able to provide acceptable comfort at the lowest

anticipated outdoor temperature. In the U.S. and abroad, most commercial

boilers have a heating capacity between 1.5 to 2 times larger than that needed

to maintain the facility’s temperature on those extreme days. Due to this

over-sizing of the boiler, the burner will cycle on and off continuously. Even

on boilers with proportional controls, once the heating load goes below the

burner’s low-fire point, the burner will cycle on and off to prevent overheating

of the system water.

IntelliCon®-CHW uses Dynamic Cycle Management (DCM) Technology to save

energy by adjusting the burner run pattern to match the system’s “heat load.”

This action is similar to the industry-accepted method of “outdoor-air temperature

reset control,” but does not require an outdoor-air temperature sensor or

the need to profile the building in order to adjust the “reset” control properly.

IntelliCon-CHW determines the “heat load” in real time by using an easily

installed strap-on temperature sensor that monitors the boiler’s out-flow water

temperature and the rate this temperature is changing.

By using our patented DCM Technology, IntelliCon-CHW increases “system

efficiency.” Thus, the heating system uses less fuel to generate the required

amount of heat. This is done by dynamically changing the aquastat’s effective

dead-band based upon the measured “heating load.” This causes the average

water temperature to vary (depending upon the measured load), and is

accomplished by extending the burner’s “off-time.” Extending the

“off-time” also results in longer, more efficient burn cycles and reduces

burner on/off time. Just as computer controls have increased the gas

mileage of automobiles, IntelliCon-CHW improves the fuel utilization of

heating systems, by supplementing the antiquated on/off control action

of the aquastat with the analysis and control capabilities of a computer.

Facility engineers will appreciate the illuminated LCD readout, displaying

the fuel consumption savings and other useful information relative to

the unit’s status, system temperatures and diagnostics, all of which are

useful during routine system maintenance.

IntelliCon-CHW typically reduces fuel consumption 10% to 20% and

decreases burner cycling by 30% or more.

Installation is simple for a qualified heating technician. The IntelliCon-CHW’s

small 7 1/2”H x 9 1/2”W x 4”D size allows it to be installed almost anywhere.

After installation, IntelliCon-CHW does not require any maintenance or

seasonal programming.

Commercial Hot Water Heating System Fuel Economizer

IntelliCon ®- CHW





200902

Light Commercial Hot Water Heating System Fuel Economizer

IntelliCon®-LCH is a microprocessor-based, fuel-saving control

for light-commercial hot-water (hydronic) heating systems.

IntelliCon-LCH reduces fuel consumption, wear on parts, flue

emissions and electrical usage, when installed on any new

or existing gas or oil burner. IntelliCon-LCH uses intelligent

Dynamic Cycle Management (DCM) Technology to save energy

by adjusting the burner run pattern to match the system’s “heat

load”. Its action is similar to the industry-accepted method of

“outdoor-air temperature reset control,” but does not require an

outdoor-air temperature sensor or the need to profile the build-

ing in order to adjust the “reset” control properly. IntelliCon-LCH

determines the “heat load” by using an easily installed strap-on

temperature sensor that monitors the boiler’s out-flow water

temperature and the rate that this temperature is changing.

Features

• For commercial systems rated up to

2.5 million BTU

• Dynamic Cycle Management

(DCM) Technology reduces fuel

consumption—typically 10% to 20%






Equipment”



components


based control




installer

• Easily programmed for maximum

savings



boiler life





IntelliCon ®- LCH

A smart way to save on yourcommercial hot water heating costs.

on® LCH is a microooprrocessor based fuel saving coH

Specifi cations

Mounting:

In any position via molded-on 1/2”

Electrical Fitting

Size:

4”H x 4”W x 2 1/2”D

Operating Humidity:



-10°F - +120°F

Power Input:

24/115/220 VAC @ 5W

Control Circuit:

24 VAC/DC, 115/220 VAC

Relay Contact:


UL Listed,


Made in U.S.A.


lowest anticipated outdoor temperatures. In the U.S. and abroad, most light



Due to this over-sizing of the boiler, the burner will cycle on and off repeatedly

to prevent overheating of the system water.

Using our intelligent Dynamic Cycle Management (DCM) Technology,

IntelliCon®-LCH increases “system efficiency.” Thus, the heating system uses

less fuel to generate the required amount of heat. This is done by dynami-

cally changing the aquastat’s effective dead-band based upon the measured

“heating load.” This causes the average water temperature to be varied

(depending upon the measured load), and is accomplished by extending the

burner’s “off-time.” Extending the “off-time” also results in longer, more

efficient burn cycles and reduces burner on/off time. Just as computer

control has increased the gas mileage of automobiles, IntelliCon-LCH with

DCM Technology improves the fuel utilization of heating systems by

supplementing the antiquated on/off control action of the aquastat with

the analysis and control capabilities of a computer.

Service personnel will appreciate the illuminated LCD readout, which displays

the fuel consumption savings and other useful information relative to the unit’s

status, system temperatures and diagnostics, all of which are useful during

routine system maintenance..

IntelliCon-LCH typically reduces fuel consumption 10% to 20%

and decreases burner cycling by 30% or more. Initial installation

programming is easily done by a qualified service technician by

following the on screen directions. After installation, IntelliCon-LCH

requires no maintenance.

Light Commercial Hot Water Heating System Fuel Economizer

IntelliCon ®- LCH





200902

Forced-Air Heating System Fuel Economizer

IntelliCon®-FA is a microprocessor-based, fuel-saving

control for forced-air heating systems. IntelliCon-FA, through

the use of our intelligent Dynamic Cycle Management

(DCM) Technology, reduces: fuel consumption, wear and

tear on parts, flue emissions and electrical usage, when

installed on any new or existing forced-air furnace.

Features


Technology is guaranteed to reduce

fuel consumption—typically 10% to

20% or more

• Saves fuel without replacing or

upgrading costly system components

and without violating manufacturers’

warranties





• Saves energy without sacrifi cing

comfort

• Short payback period—typically 4 to

18 months

• Field-tested and validated energy

saving control

• Works with any thermostat including

setback and multi-zone thermostats


Equipment”


based control



• Simple installation by qualifi ed installer

• Fail-safe operation requires no

programming or follow-up visits

• Maximum effi ciency year-round


furnace life

• 15-year replacement warranty

for breakdowns or defects

IntelliCon ®- FA

A smart way to save on your forced-air heating costs.

Specifi cations

Mounting:

In any position via molded-on

1/2” Electrical Fitting

Size:

4”H x 4”W x 2 1/2”D

Operating Humidity:



-10°F - +120°F

Power Input:

24/115/220 VAC @ 5W

Control Circuit:

24 VAC/DC, 115/220 VAC

Relay Contact:


UL Listed,


Made in U.S.A.

A heating system must keep its occupants comfortably warm at the coldest

anticipated outdoor temperature. Most forced-air heating systems in the U.S.

and abroad are between 50% and 100% larger than necessary for maintaining

a comfortable temperature on most days when the temperature is not as low

as those extreme days. This excess capacity causes the burner to cycle on

and off continuously to prevent the furnace from overheating. Even on

furnaces with programmable setback thermostats or multi-zone controls, the

burner cycling is not optimized. This burner cycling pattern wastes fuel.

IntelliCon®-FA saves energy with our Dynamic Cycle Management (DCM)

Technology by adjusting the burner run pattern to match the system’s “heat

load.” IntelliCon-FA analyzes the system’s load, or demand for heat, by

monitoring the out-flow air, or discharge-air, temperature as it is blown out of

the furnace into the structure. Optionally, the return-air can be monitored as

well for additional energy savings. The absolute temperature value of the air

in-flow and outflow, coupled with the rate that the temperature is changing, is

indicative of the load placed on the heating system. In addition, IntelliCon-FA

measures and records how many times the burner is turned on and off and

the duration of those burner cycles. IntelliCon-FA analyzes how fast heat is

being lost in the system and, in turn, in the space. Using this information, the

optimum running cycle for maintaining the desired heating level is calculated.

IntelliCon-FA then intercedes and changes the way the burner is cycled. As a

result, less fuel is consumed in delivering the same amount of heating comfort.

Just as dynamic computer control has increased the gas mileage of

automobiles: IntelliCon-FA with DCM Technology dynamically improves the

fuel utilization of forced-air heating systems. By supplementing the simplistic

on/off control action of the thermostat with the analysis and control capabilities

of a real-time computer, owners can enjoy maximum energy savings with no

sacrifice in comfort and with no adjustments required—ever. The Illuminated

LCD display shows fuel consumption savings, operating modes, system diag-

nostics and operating temperatures.

IntelliCon-FA typically reduces fuel consumption 10% to 20%.

Installation by a qualified service technician takes about 60 - 90 minutes and

does not require any programming or adjustments. The IntelliCon-FA’s small

4”H x 4”W x 2 1/2”D size allows it to be installed almost anywhere. After

installation, IntelliCon-FA does not require any maintenance and will not violate

manufacturers’ warranties.

Forced-Air Heating System Fuel Economizer

IntelliCon ®- FA





200902

Commercial Refrigeration Unit Electrical Consumption Economizer

The IntelliCon®-RU will reduce electric consumption—

typically 10% to 20%—when installed on commercial

refrigeration/freezer (refrigeration) systems. IntelliCon-RU

using intelligent Dynamic Cycle Management (DCM)

Technology represents a major advancement in refrigeration

system energy-saving technology, unsurpassed in today’s

commercial refrigeration marketplace. IntelliCon-RU is

easily installed by a qualified installer, maintenance free

and guaranteed to save energy.

Features


Technology reduces air conditioning

electric consumption—typically

10% to 20%


Equipment”



components


based control—LED indicators show

operating modes

• Protects compressor against

momentary power outages and

short cycling

• Simple installation by a qualified

HVAC/R installer

• No programming or follow-up visits

required



compressor life








IntelliCon ®- RU

A smart way to save on yourcommercial refrigeration costs.

The IntelliCon® RRUU will reduce electric consumptionU

Specifi cations

Mounting:

Any position via molded-on 1/2”

Electrical Fitting

Size:

4”H x 4” W x 2 1/2”D

Operating Humidity:



-10°F - +120°F

Power Input:

24/115/220 VAC @ 5W

Control Circuit:

24 VAC/DC, 115/220 VAC

Relay Contact:


UL Listed,


Made in U.S.A.

The IntelliCon®-RU is a microprocessor-based, UL listed, electronic control

that automatically adjusts the compressor cycles to achieve the greatest

efficiency and reduced electrical usage. The sizing of refrigeration systems

is based upon a number of factors. When any of the design considerations

are not met, the refrigeration system can become oversized for the load and

thus less efficient.

Intellidyne’s intelligent Dynamic Cycle Management (DCM) Technology

analyzes the demands and thermal characteristics of the entire refrigeration

system, and dynamically modifies the compressor cycle pattern. These

new patterns result in less frequent and more efficient compressor cycles.

Just as computer control has increased the gas mileage of automobiles,

IntelliCon-RU improves the electrical efficiency of refrigeration systems, by

supplementing the antiquated on/off action of the thermostat or pressuretrol

with the analysis and control capabilities of a computer.

The IntelliCon DCM Technology “intelligent modification of compressor cycling”

will result in significant electrical energy savings. IntelliCon’s innovative and

intelligent algorithms have field proven electrical savings not only on properly

sized and operating systems, but also on units that were undersized or those

that had not been properly maintained.

The IntelliCon-RU works in conjunction with the existing temperature

controls and will not void the compressor manufacturer’s warranty.

An additional feature of the IntelliCon-RU is the accepted industry

practice of compressor anti-short-cycling control.

Installation by a qualified HVAC/R service technician is recommended.

The IntelliCon-RU does not require any programming, adjustments or

maintenance.

Commercial Refrigeration Unit Electrical Consumption Economizer

IntelliCon ®- RU





200902

Date post:	24-Jun-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

IntelliCon®- CAC · IntelliCon®-CHS is a microprocessor-based, fuel-saving control for commercial...

Documents