Interoperability Report - Site root - AscomPartnerWeb Report Ascom i62 Cisco WLC WLC controller...

Interoperability Report

Ascom i62

Cisco WLC

WLC controller platform

Cisco WLC v. 8.5.103

Ascom i62 v. 6.0.1

Morrisville, NC, USA

October 2017

Interoperability Report Date Page Ascom i62 Cisco WLC 2017-10-03 2 / 25

Contents

Introduction ...................................................................................................................................... 3

About Ascom .................................................................................................................................. 3

About Cisco .................................................................................................................................... 3

Site Information ............................................................................................................................... 4

Verification site ............................................................................................................................... 4

Participants .................................................................................................................................... 4

Verification topology ....................................................................................................................... 4

Summary .......................................................................................................................................... 5

General conclusions ....................................................................................................................... 5

Compatibility information ................................................................................................................ 5

Verification overview ...................................................................................................................... 6

Known limitations ........................................................................................................................... 7

Appendix A: Verification Configurations....................................................................................... 8

Cisco WLC 5508 Version 8.5.103 .................................................................................................. 8

Ascom i62 .................................................................................................................................... 22

Appendix B: Detailed Verification Records ................................................................................. 25

Document History .......................................................................................................................... 25


Introduction

This document describes a summary of the interoperability verification results of the Ascoms and Ciscos

platform, necessary steps and guidelines to optimally configure the platforms and support contact details. The

report should be used in conjunction with both Ciscos and Ascoms platform configuration guides.

About Ascom

Ascom is a global solutions provider focused on healthcare ICT and mobile workflow solutions. The

vision of Ascom is to close digital information gaps allowing for the best possible decisions anytime

and anywhere. Ascoms mission is to provide mission-critical, real-time solutions for highly mobile, ad

hoc, and time-sensitive environments. Ascom uses its unique product and solutions portfolio and

software architecture capabilities to devise integration and mobilization solutions that provide truly

smooth, complete and efficient workflows for healthcare as well as for industry, security and retail

sectors.

Ascom is headquartered in Baar (Switzerland), has subsidiaries in 15 countries and employs around

1,300 people worldwide. Ascom registered shares (ASCN) are listed on the SIX Swiss Exchange in

Zurich.

About Cisco

Cisco (NASDAQ: CSCO) is the worldwide technology leader that has been making the Internet work

since 1984. Our people, products and partners help society securely connect and seize tomorrow's

digital opportunity today. Discover more at thenetwork.cisco.com and follow us on Twitter at @Cisco.


Site Information

Verification site Ascom US

300 Perimeter park drive

Morrisville, NC, US-27560

USA

Participants

Karl-Magnus Olsson, Ascom, Morrisville

Verification topology


Summary

General conclusions

Ascom interoperability verification produced very good results with a few exceptions. Cisco AP1852 and AP1832

showed issues with passing data to power save clients and have therefor been suspended temporarily until the

problem is resolved. For details regarding this and other issue refer to Known limitations on page 7.

Compatibility information

One Access point model from every product generation has been selected as a representation (AP3500, 3600,

3700 3800 and 1850). By testing these access points we are considered cover all major Cisco access points

based on chipset compatibility.

Supported Partner Access Points with SW version 8.5.103:

AP1140, 1250, 1260, 3500

AP1600, 2600, 3600

AP1700, 2700, 3700

AP2800, 3800,

AP1830, 1850

Supported Partner Controller Platforms with SW version 8.5.103:

Cisco 2500 Series Wireless Controllers (Cisco 2504 Wireless Controller)

Cisco 3500 Series Wireless Controllers (Cisco 3504 Wireless Controller)

Cisco 5500 Series Wireless Controllers (Cisco 5508 and 5520 Wireless Controllers)

Cisco Flex 7500 Series Wireless Controllers (Cisco Flex 7510 Wireless Controller)

Cisco 8500 Series Wireless Controllers (Cisco 8510 and 8540 Wireless Controllers)

Cisco Virtual Wireless Controller (vWLC) (VMware ESXi, HyperV, and KVM)


Verification overview

WLAN Compatibility and Performance

High Level Functionality Result Comments

Association, Open with No Encryption OK

Association, WPA2-PSK / AES Encryption OK

Association, PEAP-MSCHAPv2 Auth, AES Encryption OK

Association with EAP-TLS authentication OK

Association, Multiple ESSIDs OK

Beacon Interval and DTIM Period OK

PMKSA Caching OK

WPA2-opportunistic/proactive Key Caching OK

WMM Prioritization OK

802.11 Power-save mode OK

802.11e U-APSD OK

802.11e U-APSD (load test) OK

Roaming, WPA2-PSK, AES Encryption OK * Typical roaming time 49 ms

Roaming, PEAP-MSCHAPv2 Auth, AES Encryption OK ** Typical roaming time 46 ms

Roaming, EAP-FAST, CCKM OK Typical roaming time 37 ms

*) Average roaming times are measured using 802.11a/n. Refer to Appendix B for detailed test results

* *) Measured times is with opportunistic/proactive Key Caching enabled (default enabled)


Known limitations

Description and Consequence Workaround Ticket(s)

raised

AP 1832 and AP1852 periodically stops sending downlink data resulting in lost data and voice streams. High impact. Support for AP1832 and 1852 has temporarily been revoked until issue has been corrected.

Use previously certified firmware.

Cisco ticket: CSCve36498 Ascom ticket: INTOP-81

Note that Cisco AP 2800 and 3800 does not support full CCX and DTPC. Refer to Cisco release notes for additional information.

Call Admission Control/TSPEC. Beacon and Probe response information in QBSS IE - "Available Admission Capacity" does not decrease with added calls. Hence i62 might still consider access points that have reached their capacity limit to be roaming candidates. Potential loss of speech. AP2800/3800 only. Investigation is ongoing.

Disable Call Admission

Control

Call Admission Control and EAP-FAST does not work together. All requests for admission will be declined even if bandwidth is available. Works with PSK, PEAP, EAP-TLS.

Disable Call Admission

Control when using EAP-

FAST as Authentication

method.

Ascom ticket:

INTOP-81

For additional information regarding the known limitations please contact [email protected] or [email protected].

For detailed verification results, refer to Appendix B: Detailed Verification Records.

mailto:[email protected]:[email protected]


Appendix A: Verification Configurations

Cisco WLC 5508 Version 8.5.103

In the following chapter you will find screenshots and explanations of basic settings in order to get a Cisco WLC

WLAN system to operate with an Ascom i62. Please note that security settings were modified according to

requirements in individual test cases.

Security settings (PSK)

Example of how to configure the system for PSK (WPA2-AES)

Security profile WPA2-PSK, AES encryption

- Select WPA2 Policy with AES encryption. - Select PSK and enter a key (Here in ASCII format)


802.1X authentication (PEAP-MSCHAPv2).

Example of how to configure the system for .1X authentication

Configuration of authentication using external Radius sever, 802.1X (Step 1). In this example is WPA2-AES used.

Select 802.1X as Authentication Key Management.

Note. To use CCKM, replace 802.1X with CCKM check box. The security mode in the i62 has to be set to

Advanced and CCKM has to be selected as Authentication Key Management instead of the default

802.1X.


Example of authentication configuration using external Radius sever (Step 2). Select the server to use. The server

is configured under tab Security/Radius. See configuration of server below.


Configuration of authentication using external Radius sever (Step 3). The IP address and the secret must

correspond to the IP and the credential used by the Radius server. Tests were performed using Cisco ACS as

RADIUS server.

Note. Depending authentication method used it might be necessary to add a certificate into the i62. PEAP-

MSCHAPv2 requires a CA certificate and EAP-TLS requires both a CA certificate and a client certificate.

Server certificate validation can be overridden in version 4.1.12 and above per handset setting.

Note. Refer to the i62 section in Appendix A for matching handset configurations.


EAP-FAST using an internal authentication server.

Configuration of authentication using internal Radius sever and EAP-FAST (Step 1). In this example is WPA2-

AES/CCMP used.

Note. To use CCKM, replace 802.1X with CCKM check box. The security mode in the i62 has to be set to

Advanced and CCKM has to be selected as Authentication Key Management instead of the default

802.1X.


Configuration of authentication using internal Radius sever and EAP-FAST (Step 2). Check the box Local EAP

Authentication and choose your local EAP profile (created in step 4).

Configuration of authentication using internal Radius sever and EAP-FAST (Step 3). Create a local user and

assign a password.


Configuration of authentication using internal Radius sever and EAP-FAST (Step 4). Create a local EAP profile

and choose the EAP method to use.


General settings (QoS, Radio)

Set QoS to Platinum (Voice)

Make sure that WMM policy is set to Required


Make sure Session timeout is disabled. Coverage Hole Detection can be left enabled if RRM is used in the

system. Set DTIM period to Ascom recommended value 5. DTIM value 5 values are recommended in order to

allow maximum battery conservation without impacting the quality. Using a lower DTIM value is possible but will

reduce the standby time.

Make sure 11k Neighbor list is disabled.


Channel configuration. See next picture for additional information.

Ascom recommended settings for 802.11b/g/n are to only use channel 1, 6 and 11. For 802.11a/n/ac use

channels according to the infrastructure manufacturer, country regulations and per guidelines below.

Note that Tx power level and channel was manually set for test purpose.

General guidelines when deploying Ascom i62 handsets in 802.11a/n/ac environments:

1. Enabling more than 8 channels will degrade roaming performance. In situations where UNII1 and UNII3 are used, a maximum of 9 enabled channels can be allowed.

Ascom does not recommend exceeding this limit.

2. Using 40 MHz channels (or channel-bonding) will reduce the number of non-DFS* channels to two in ETSI regions (Europe). In FCC regions (North America), 20MHz is a more viable option because of the availability of additional non-DFS channels. The handset can co-exist with 40MHz stations in the same ESS.

3. Ascom do support and can coexist in 80MHz channel bonding environments. The recommendations is however to avoid 80MHz channel bonding as it severely reduces the number of available non overlapping channels.

4. Make sure that all non-DFS channel are taken before resorting to DFS channels. The handset can cope in mixed non-DFS and DFS environments; however, due to unpredictability introduced by radar detection protocols, voice quality may become distorted and roaming delayed. Hence Ascom recommends if possible avoiding the use of DFS channels in VoWIFI deployments.

*) Dynamic Frequency Selection (radar detection)


The default data rate set will work just fine, however Ascom recommends disabling the lowest speeds and have

12Mbits as lowest supported speed.

As Ascom i62 do support Channel Switch Announcement its recommended to have this setting enabled in the

system (only applicable when DFS channels are used)


Ascom does support both usage of 11n Mode and 11ac Mode including 40 MHz and 80MHz channels

Note. Follow the recommendations General guidelines when deploying Ascom i62 handsets in

802.11a/n/ac environments on Page 16


The default data rate set will work just fine, however Ascom recommends disabling the lowest speeds and have

12Mbits as lowest supported speed. To further optimize performance it is recommended to disallow 802.11b

clients to associate by setting 12Mbps rate to mandatory in 802.11g configuration.

Ascom recommends EDCA Profile: Voice Optimized

Make sure Low Latency MAC is disabled. (Both 802.11a/n/ac and 802.11b/g/n)

Note. Using EDCA Profile WMM is acceptable but Voice Optimized is to prefer when voice clients are

present in the system.


Depending on the infrastructure (switches) Protocol Type may have to be disabled.


Ascom i62

Network settings for WPA2-PSK

Note. Make sure that the enabled channels in the i62 handset match the channel plan used in the system.

Note. FCC is no longer allowing 802.11d to determine regulatory domain. Devices deployed in USA must

set Regulatory domain to USA.


Network settings for .1X authentication (PEAP-MSCHAPv2)


802.1X Authentication requires a CA certificate to be uploaded to the phone by right clicking - > Edit certificates.

EAP-TLS will require both a CA and a client certificate.

Note that both a CA and a client certificate are needed for TLS. Otherwise only a CA certificate is needed.

Server certificate validation can be overridden in version 4.1.12 and above per handset setting.


Appendix B: Detailed Verification Records

Pass

Fail

Comments

Not verified

17

0

0

6

Total 23

Refer to the attached file for detailed verification results.

Refer to the verification specification for explicit information regarding each verification case.

The specification can be found here (requires login):

https://www.ascom-ws.com/AscomPartnerWeb/en/startpage/Sales-tools/Interoperability/Templates/

Document History

Rev Date Author Description

P1 3-Oct-17 SEKMO Draft

R1 18-Oct-17 SEKMO Updates after review.

https://www.ascom-ws.com/AscomPartnerWeb/en/startpage/Sales-tools/Interoperability/Templates/

i62

WLAN Interoperability Test ReportWLAN configuration:

Beacon Interval: 100ms

Test object - Handset:DTIM Interval: 5

Ascom i62 version 6.0.1802.11d Regulatory Domain: World

Test object - WLAN system:WMM Enabled (Auto/WMM)

Cisco WLC 5508, Version 8.5.103No Auto-tune

AP 1850, 3500, 3600, 3700, 3800AP3702AP3602AP3502AP3800AP1850Single Voice VLAN

2.4Ghz5.0Ghz2.4Ghz5.0Ghz2.4Ghz5.0Ghz2.4Ghz5.0Ghz2.4Ghz5.0Ghz

Test CaseDescriptionVerdictVerdictVerdictVerdictVerdictVerdictVerdictVerdictVerdictVerdictComment

TEST AREA ASSOCIATION / AUTHENTICATION

#101Association with open authentication, no encryptionPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTED

#107Association with WPA2-PSK authentication, AES-CCMP encryptionPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDHidden SSID validated.

#110Association with PEAP-MSCHAPv2 auth, AES-CCMP encryptionPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDFreeRADIUS server; RootCA loaded to device;FAIL

#111Association with EAP-FAST authenticationPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDWLC internal authtication server

#116Association with EAP-TLS authenticationPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDFreeRADIUS server; Root CA and client cert loaded to device;

TEST AREA POWER-SAVE AND QOSPASS

#150802.11 Power-save modePASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDFAIL

#151Beacon period and DTIM intervalNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#152802.11e U-APSDPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDSee Comment

#202WMM prioritizationPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDIperf for load generation of unprioritized data

TEST AREA "PERFORMANCE"

#308Power-save mode U-APSD WPA2-PSKNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#310CAC - TSPECPASSPASSPASSPASSPASSPASSSee CommentSee CommentNOT TESTEDNOT TESTEDAP 2800/3800: QBSS "Availible admission capacity" does not decrease with added calls. All Aps: CAC not working with EAP-FAST - always declined admission

TEST AREA ROAMING AND HANDOVER TIMES

#401Handover with open authentication and no encryptionNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#404Handover with WPA2-PSK auth and AES-CCMP encryptionPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDAVG roaming time 11an: 49ms, bgn: 45ms (No significnat difference seen in roaming times between different AP models). AP1832 - AP stops sending data periodically.

#408Handover with PEAP-MSCHAPv2 authentication and AES-CCMP encryptionPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDAVG roaming time 11an: 46ms, bgn: 52ms (No significant difference seen in roaming times between different AP models). AP1832 - AP stops sending data periodically.

#411Handover using PMKSA and opportunistic/proactive key cachingPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDOKC enabled by default. Same test case as #408

#409EAP-FAST CCKMPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDAVG roaming time an: 33ms, gn: 37ms (No significant difference seen in roaming times between different AP models).

TEST AREA BATTERY LIFETIME

#501Battery lifetime in idleNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#504Battery lifetime in call with power save mode U-APSDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDPASSPASSNOT TESTED12h+ in call. Default settings and non-DFS channels only

TEST AREA STABILITY

#602Duration of call U-APSD modePASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTED>1hrs stable call without interruption, AP1832 - unable to maintain call

TEST AREA 802.11n

#801Frame aggregation A-MSDUPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDNo frame aggregation in UP6 by default settings.

#802Frame aggregation A-MPDUNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTEDNOT TESTED

#80440Mhz channelsNOT TESTEDPASSNOT TESTEDPASSNOT TESTEDPASSNOT TESTEDPASSNOT TESTEDNOT TESTED

#805802.11n ratesPASSPASSPASSPASSPASSPASSPASSPASSNOT TESTEDNOT TESTEDOK

show running-config

Notice: "show running-config" has been changed to be an alias to "show run-config".Use "show run-config commands" to display the configuration commands.Press Enter to continue or to abort...

System Inventory

NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"

PID: AIR-CT5508-K9, VID: V01, SN: FCW1444L002

Burned-in MAC Address............................ F8:66:F2:FA:75:A0Power Supply 1................................... Present, OKPower Supply 2................................... AbsentMaximum number of APs supported.................. 500Press Enter to continue or to abort

System InformationManufacturer's Name.............................. Cisco Systems Inc.Product Name..................................... Cisco ControllerProduct Version.................................. 8.5.103.0Bootloader Version............................... 1.0.20Field Recovery Image Version..................... 7.6.101.1Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2OUI File Last Update Time........................ Sun Sep 07 10:44:07 IST 2014

Build Type....................................... DATA + WPS

System Name...................................... Cisco_fa:75:a4System Location.................................. System Contact................................... System ObjectID.................................. 1.3.6.1.4.1.9.1.1069Redundancy Mode.................................. DisabledIP Address....................................... 192.168.0.15IPv6 Address..................................... ::Last Reset....................................... Software resetSystem Up Time................................... 13 days 23 hrs 29 mins 18 secsSystem Timezone Location.........................

--More or (q)uit current module or to abortSystem Stats Realtime Interval................... 5System Stats Normal Interval..................... 180

Configured Country............................... Multiple Countries : SE,USOperating Environment............................ Commercial (0 to 40 C)Internal Temp Alarm Limits....................... 0 to 65 CInternal Temperature............................. +38 CExternal Temperature............................. +26 CFan Status....................................... OK

State of 802.11b Network......................... EnabledState of 802.11a Network......................... EnabledNumber of WLANs.................................. 6Number of Active Clients......................... 10

OUI Classification Failure Count................. 0

Burned-in MAC Address............................ F8:66:F2:FA:75:A0Power Supply 1................................... Present, OKPower Supply 2................................... AbsentMaximum number of APs supported.................. 500System Nas-Id.................................... Cisco_fa:75:a4WLC MIC Certificate Types........................ SHA1

--More or (q)uit current module or to abortPress Enter to continue or to abort

Backup Controller Configuration

AP primary Backup Controller .................... AP secondary Backup Controller .................. Press Enter to continue or to abort

System Time Information:

Time............................................. Fri Sep 22 12:52:01 2017

Timezone delta................................... 0:0Timezone location................................

NTP Servers NTP Polling Interval......................... 600

Index NTP Key Index NTP Server Status NTP Msg Auth Status ------- ----------------------------------------------------------------------------------------------

Press Enter to continue or to abort

Redundancy InformationRedundancy Mode ................................. SSO DISABLED

Local State...................................... ACTIVEPeer State....................................... N/A

Unit............................................. Primary

Unit ID.......................................... F8:66:F2:FA:75:A0

Redunadancy State................................ N/A

Mobility MAC..................................... F8:66:F2:FA:75:A0

Redundancy Management IP Address................. 0.0.0.0Peer Redundancy Management IP Address............ 0.0.0.0Redundancy Port IP Address....................... 0.0.0.0Peer Redundancy Port IP Address.................. 169.254.0.0Press Enter to continue or to abort

AP Bundle Information

Primary Version : 8.5.103.0

AP Supplement Bundle : Not Installed

Primary AP ImageSizeSupported AP's --------------------------------ap1g113320AP700ap1g426192AP1850/1810ap1g522680AP1815,1540ap3g110156AP3500ap3g215400AP2600,3600ap3g339916AP2800,3800,1560c370014692AP1700,2700,3700

Secondary Version : 8.3.121.9

AP Supplement Bundle : Not Installed

--More or (q)uit current module or to abortSecondary AP ImageSizeSupported AP's ----------------------------------ap1g113120AP700ap1g213072AP1600ap1g423148AP1850/1810ap1g519016AP1815,1540ap3g19936AP3500ap3g214932AP2600,3600ap3g328244AP2800,3800,1560c11408836AP802c602i3864AP802Press Enter to continue or to abort

Switch Configuration802.3x Flow Control Mode......................... Disable FIPS prerequisite features....................... DisabledWLANCC prerequisite features..................... DisabledUCAPL prerequisite features...................... DisabledDTLS WLC MIC .................................... SHA2secret obfuscation............................... EnabledStrong Password Check Features case-check.................................... Enabled consecutive-check............................. Enabled default-check................................. Enabled username-check................................ Enabled position-check................................ Disabled case-digit-check.............................. Disabled Min. Password length.......................... 3 Min. Upper case chars......................... 0 Min. Lower case chars......................... 0 Min. Digits chars............................. 0 Min. Special chars............................ 0Mgmt User Password Lifetime [days]...................... 0 Password Lockout.............................. Disabled

--More or (q)uit current module or to abort Lockout Attempts.............................. 0 Lockout Timeout [mins]........................ 0SNMPv3 User Password Lifetime [days]...................... 0 Password Lockout.............................. Disabled Lockout Attempts.............................. 3 Lockout Timeout [mins]........................ 5Press Enter to continue or to abort

Network InformationRF-Network Name............................. ascomDNS Server IP............................... 0.0.0.0Web Mode.................................... DisableSecure Web Mode............................. EnableSecure Web Mode Cipher-Option High.......... DisableSecure Web Mode SSL Protocol................ DisableWeb CSRF check.............................. EnableOCSP........................................ DisabledOCSP responder URL.......................... Secure Shell (ssh).......................... EnableSecure Shell (ssh) Cipher-Option High....... DisableTelnet...................................... DisableEthernet Multicast Forwarding............... DisableEthernet Broadcast Forwarding............... DisableIPv4 AP Multicast/Broadcast Mode............ UnicastIPv6 AP Multicast/Broadcast Mode............ UnicastIGMP snooping............................... DisabledIGMP timeout................................ 60 secondsIGMP Query Interval......................... 20 secondsMLD snooping................................ DisabledMLD timeout................................. 60 seconds

--More or (q)uit current module or to abortMLD query interval.......................... 20 secondsUser Idle Timeout........................... 300 secondsARP Idle Timeout............................ 300 secondsCisco AP Default Master..................... DisableAP Join Priority............................ DisableMgmt Via Wireless Interface................. EnableMgmt Via Dynamic Interface.................. DisableBridge MAC filter Config.................... EnableBridge Security Mode........................ EAPMesh Full Sector DFS........................ EnableMesh Backhaul RRM........................... DisableAP Fallback ................................ EnableAP EasyAdmin ............................... DisableAP Virtual IP .............................. 0.0.0.0Web Auth CMCC Support ...................... DisabledWeb Auth Redirect Ports .................... 80Web Auth Proxy Redirect ................... DisableWeb Auth Captive-Bypass .................. DisableWeb Auth Secure Web ....................... EnableWeb Auth Secure Web Cipher Option ......... DisableWeb Auth Secure Web Sslv3 ................. DisableWeb Auth Secure Redirection ............... DisableFast SSID Change ........................... Disabled

--More or (q)uit current module or to abortAP Discovery - NAT IP Only ................. EnabledIP/MAC Addr Binding Check .................. EnabledLink Local Bridging Status ................. DisabledCCX-lite status ............................ Disableoeap-600 dual-rlan-ports ................... Disableoeap local-network ......................... Enableoeap-600 Split Tunneling (Printers)......... DisableWebPortal Online Client .................... 0WebPortal NTF_LOGOUT Client ................ 0mDNS snooping............................... DisabledmDNS Query Interval......................... 15 minutesWeb Color Theme............................. DefaultCapwap Prefer Mode.......................... IPv4Network Profile............................. DisabledClient ip conflict detection (DHCP) ........ DisabledMesh BH RRM ................................ DisableMesh Aggressive DCA......................... DisableMesh Auto RF................................ DisableHTTP Profiling Port......................... 80HTTP-Proxy Ip Address....................... 0.0.0.0HTTP-Proxy Port............................. 80WGB Client Forced L2 Roam................... DisabledPress Enter to continue or to abort

Port Summary STP Admin Physical Physical Link LinkPr Type Stat Mode Mode Status Status Trap POE SFPType -- ------- ---- ------- ---------- ---------- ------ ------- ------- ----------1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseSX 2 Normal Disa Enable Auto Auto Down Enable N/A Not Present 3 Normal Disa Enable Auto Auto Down Enable N/A Not Present 4 Normal Disa Enable Auto Auto Down Enable N/A Not Present 5 Normal Disa Enable Auto Auto Down Enable N/A Not Present 6 Normal Disa Enable Auto Auto Down Enable N/A Not Present 7 Normal Disa Enable Auto Auto Down Enable N/A Not Present 8 Normal Disa Enable Auto Auto Down Enable N/A Not Present RP Normal Disa Enable Auto Auto Down Enable N/A 1000BaseTX SP Normal Forw Enable Auto Auto Up Enable N/A 1000BaseTX Press Enter to continue or to abort

AP SummaryNumber of APs.................................... 1

Global AP User Name.............................. Not ConfiguredGlobal AP Dot1x User Name........................ Not Configured

AP Name Slots AP Model Ethernet MAC Location Country IP Address Clients DSE Location ------------------------------ ----- -------------------- ----------------- -------------------- ---------- --------------- ------- --------------AP7c0e.cefb.97d0 2 AIR-CAP3702I-A-K9 7c:0e:ce:fb:97:d0 default location US 192.168.0.158 10 [0 ,0 ,0 ]

AP Tcp-Mss-Adjust InfoAP Name TCP State MSS Size------------------ -------- ------- AP7c0e.cefb.97d0 disabled -Press Enter to continue or to abort

AP LocationTotal Number of AP Groups........................ 2

Site Name........................................ Group1Site Description................................. Venue Group Code................................. UnspecifiedVenue Type Code.................................. Unspecified

NAS-identifier................................... noneClient Traffic QinQ Enable....................... FALSEDHCPv4 QinQ Enable............................... FALSEAP Operating Class............................... Not-configuredCapwap Prefer Mode............................... Not-configured

RF Profile----------2.4 GHz band..................................... High-Client-Density-802.11bg5 GHz band....................................... High-Client-Density-802.11a

WLAN ID Interface Network Admission Control Radio Policy OpenDnsProfile------- ----------- -------------------------- ------------ --------------

--More or (q)uit current module or to abort

*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.

Lan Port configs ----------------

LAN Status POE RLAN--- ------- ---- ----- 1 Disabled Disabled None 2 Disabled None 3 Disabled None

External 3G/4G module configs -----------------------------

LAN Status POE RLAN--- ------- ---- ----- 1 Disabled None

AP Name Slots AP Model Ethernet MAC Location Port Country Priority------------------ ----- ------------------- ----------------- ---------------- ---- ------- --------


Fabric Flex Acl Template Name ................... Not Configured

Site Name........................................ default-groupSite Description................................. NAS-identifier................................... noneClient Traffic QinQ Enable....................... FALSEDHCPv4 QinQ Enable............................... FALSEAP Operating Class............................... Not-configuredCapwap Prefer Mode............................... Not-configured

RF Profile----------2.4 GHz band..................................... 5 GHz band.......................................

WLAN ID Interface Network Admission Control Radio Policy OpenDnsProfile------- ----------- -------------------------- ------------ -------------- 1 management Disabled None None 2 management Disabled None None 3 management Disabled None None 4 management Disabled None None 5 management Disabled None None

--More or (q)uit current module or to abort 6 management Disabled None None

*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.

Lan Port configs ----------------

LAN Status POE RLAN--- ------- ---- ----- 1 Disabled Disabled None 2 Disabled None 3 Disabled None

External 3G/4G module configs -----------------------------

LAN Status POE RLAN--- ------- ---- ----- 1 Disabled None

AP Name Slots AP Model Ethernet MAC Location Port Country Priority------------------ ----- ------------------- ----------------- ---------------- ---- ------- --------

--More or (q)uit current module or to abortAP7c0e.cefb.97d0 2 AIR-CAP3702I-A-K9 7c:0e:ce:fb:97:d0 default location 1 US 1

Fabric Flex Acl Template Name ................... Not ConfiguredPress Enter to continue or to abort

RF Profile

Number of RF Profiles............................ 6

Out Of Box State................................. Disabled

Out Of Box Persistence........................... Disabled

RF Profile Name Band Description 11n-client-only Applied --------------------------------- ------- ----------------------------------- ------------------ ----------High-Client-Density-802.11a 5 GHz disable Yes High-Client-Density-802.11bg 2.4 GHz disable Yes Low-Client-Density-802.11a 5 GHz disable No Low-Client-Density-802.11bg 2.4 GHz disable No Typical-Client-Density-802.11a 5 GHz disable No Typical-Client-Density-802.11bg 2.4 GHz disable No

RF Profile name................................ High-Client-Density-802.11aDescription...................................... AP Group Name.................................... Group1Radio policy..................................... 5 GHz

--More or (q)uit current module or to abort11n-client-only.................................. disabledTransmit Power Threshold v1...................... -65 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... 7 dBmMax Transmit Power............................... 30 dBm802.11a Operational Rates 802.11a 6M Rate.............................. Disabled 802.11a 9M Rate.............................. Disabled 802.11a 12M Rate............................. Mandatory 802.11a 18M Rate............................. Supported 802.11a 24M Rate............................. Supported 802.11a 36M Rate............................. Supported 802.11a 48M Rate............................. Supported 802.11a 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600


6 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. -78 dBmCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled

Client Aware FRA State........................................ Disabled Client Select Utilization Threshold.......... 50% Client Reset Utilization Threshold........... 5%

Band Select Probe Response............................... Disabled Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds Expire Dual Band............................. 60 seconds

--More or (q)uit current module or to abort Client Rssi.................................. -80 dBm Client Mid Rssi.............................. -80 dBm

Load Balancing Denial....................................... 3 count Window....................................... 5 clients

Coverage Data Data......................................... -80 dBm Voice........................................ -80 dBm Minimum Client Level......................... 3 clients Exception Level.............................. 25 %DCA Channel List................................. 36DCA Bandwidth.................................... 40DCA Foreign AP Contribution...................... enabled

802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled MCS-15 Rate.................................. enabled MCS-16 Rate.................................. enabled MCS-17 Rate.................................. enabled MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled MCS-20 Rate.................................. enabled MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled Client Network Preference....................... default

RF Profile name................................ High-Client-Density-802.11bgDescription...................................... AP Group Name.................................... Group1Radio policy..................................... 2.4 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -70 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... 7 dBmMax Transmit Power............................... 30 dBm802.11b/g Operational Rates 802.11b/g 1M Rate............................ Disabled 802.11b/g 2M Rate............................ Disabled 802.11b/g 5.5M Rate.......................... Disabled 802.11b/g 11M Rate........................... Disabled 802.11g 6M Rate.............................. Disabled 802.11g 9M Rate.............................. Supported 802.11g 12M Rate............................. Mandatory 802.11g 18M Rate............................. Supported

--More or (q)uit current module or to abort 802.11g 24M Rate............................. Supported 802.11g 36M Rate............................. Supported 802.11g 48M Rate............................. Supported 802.11g 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. -82 dBmCca Threshold.................................... 0 dBm

--More or (q)uit current module or to abortSlot Admin State:................................ Enabled


Band Select Probe Response............................... Disabled Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds Expire Dual Band............................. 60 seconds Client Rssi.................................. -80 dBm Client Mid Rssi.............................. -80 dBm


Coverage Data Data......................................... -80 dBm Voice........................................ -80 dBm

--More or (q)uit current module or to abort Minimum Client Level......................... 3 clients Exception Level.............................. 25 %DCA Channel List................................. 1,6,11DCA Bandwidth.................................... 20DCA Foreign AP Contribution...................... enabled

802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled MCS-15 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-16 Rate.................................. enabled MCS-17 Rate.................................. enabled MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled MCS-20 Rate.................................. enabled MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled Client Network Preference....................... default

RF Profile name................................ Low-Client-Density-802.11aDescription...................................... AP Group Name.................................... Radio policy..................................... 5 GHz11n-client-only.................................. disabled

--More or (q)uit current module or to abortTransmit Power Threshold v1...................... -60 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm802.11a Operational Rates 802.11a 6M Rate.............................. Disabled 802.11a 9M Rate.............................. Disabled 802.11a 12M Rate............................. Mandatory 802.11a 18M Rate............................. Supported 802.11a 24M Rate............................. Supported 802.11a 36M Rate............................. Supported 802.11a 48M Rate............................. Supported 802.11a 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600




Band Select Probe Response............................... Disabled Cycle Count.................................. 2 cycles Cycle Threshold.............................. 200 milliseconds Expire Suppression........................... 20 seconds Expire Dual Band............................. 60 seconds Client Rssi.................................. -80 dBm

--More or (q)uit current module or to abort Client Mid Rssi.............................. -80 dBm



802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled


--More or (q)uit current module or to abort MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled Client Network Preference....................... default

RF Profile name................................ Low-Client-Density-802.11bgDescription...................................... AP Group Name.................................... Radio policy..................................... 2.4 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -65 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm802.11b/g Operational Rates 802.11b/g 1M Rate............................ Disabled 802.11b/g 2M Rate............................ Disabled 802.11b/g 5.5M Rate.......................... Disabled 802.11b/g 11M Rate........................... Mandatory 802.11g 6M Rate.............................. Disabled 802.11g 9M Rate.............................. Disabled 802.11g 12M Rate............................. Supported 802.11g 18M Rate............................. Supported 802.11g 24M Rate............................. Supported

--More or (q)uit current module or to abort 802.11g 36M Rate............................. Supported 802.11g 48M Rate............................. Supported 802.11g 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600






Coverage Data Data......................................... -90 dBm Voice........................................ -90 dBm Minimum Client Level......................... 3 clients

--More or (q)uit current module or to abort Exception Level.............................. 25 %DCA Channel List................................. 1,6,11DCA Bandwidth.................................... 20DCA Foreign AP Contribution...................... enabled

802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled MCS-15 Rate.................................. enabled MCS-16 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-17 Rate.................................. enabled MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled MCS-20 Rate.................................. enabled MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled Client Network Preference....................... default

RF Profile name................................ Typical-Client-Density-802.11aDescription...................................... AP Group Name.................................... Radio policy..................................... 5 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -70 dBm

--More or (q)uit current module or to abortTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm802.11a Operational Rates 802.11a 6M Rate.............................. Disabled 802.11a 9M Rate.............................. Disabled 802.11a 12M Rate............................. Mandatory 802.11a 18M Rate............................. Supported 802.11a 24M Rate............................. Supported 802.11a 36M Rate............................. Supported 802.11a 48M Rate............................. Supported 802.11a 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600

--More or (q)uit current module or to abortTrap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. AUTOCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled






802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled


--More or (q)uit current module or to abort MCS-31 Rate.................................. enabled Client Network Preference....................... default

RF Profile name................................ Typical-Client-Density-802.11bgDescription...................................... AP Group Name.................................... Radio policy..................................... 2.4 GHz11n-client-only.................................. disabledTransmit Power Threshold v1...................... -70 dBmTransmit Power Threshold v2...................... -67 dBmMin Transmit Power............................... -10 dBmMax Transmit Power............................... 30 dBm802.11b/g Operational Rates 802.11b/g 1M Rate............................ Disabled 802.11b/g 2M Rate............................ Disabled 802.11b/g 5.5M Rate.......................... Disabled 802.11b/g 11M Rate........................... Disabled 802.11g 6M Rate.............................. Disabled 802.11g 9M Rate.............................. Supported 802.11g 12M Rate............................. Mandatory 802.11g 18M Rate............................. Supported 802.11g 24M Rate............................. Supported 802.11g 36M Rate............................. Supported

--More or (q)uit current module or to abort 802.11g 48M Rate............................. Supported 802.11g 54M Rate............................. SupportedMax Clients...................................... 200

WLAN ID Max Clients

------- -------

1 600

2 600

3 600

4 600

5 600

6 600

Trap Threshold Clients...................................... 12 clients Interference................................. 10 % Noise........................................ -70 dBm Utilization.................................. 80 %Multicast Data Rate.............................. 0Rx Sop Threshold................................. AUTOCca Threshold.................................... 0 dBmSlot Admin State:................................ Enabled

--More or (q)uit current module or to abortClient Aware FRA State........................................ Disabled Client Select Utilization Threshold.......... 50% Client Reset Utilization Threshold........... 5%



Coverage Data Data......................................... -80 dBm Voice........................................ -80 dBm Minimum Client Level......................... 3 clients Exception Level.............................. 25 %

--More or (q)uit current module or to abortDCA Channel List................................. 1,6,11DCA Bandwidth.................................... 20DCA Foreign AP Contribution...................... enabled

802.11n MCS Rates MCS-00 Rate.................................. enabled MCS-01 Rate.................................. enabled MCS-02 Rate.................................. enabled MCS-03 Rate.................................. enabled MCS-04 Rate.................................. enabled MCS-05 Rate.................................. enabled MCS-06 Rate.................................. enabled MCS-07 Rate.................................. enabled MCS-08 Rate.................................. enabled MCS-09 Rate.................................. enabled MCS-10 Rate.................................. enabled MCS-11 Rate.................................. enabled MCS-12 Rate.................................. enabled MCS-13 Rate.................................. enabled MCS-14 Rate.................................. enabled MCS-15 Rate.................................. enabled MCS-16 Rate.................................. enabled MCS-17 Rate.................................. enabled

--More or (q)uit current module or to abort MCS-18 Rate.................................. enabled MCS-19 Rate.................................. enabled MCS-20 Rate.................................. enabled MCS-21 Rate.................................. enabled MCS-22 Rate.................................. enabled MCS-23 Rate.................................. enabled MCS-24 Rate.................................. enabled MCS-25 Rate.................................. enabled MCS-26 Rate.................................. enabled MCS-27 Rate.................................. enabled MCS-28 Rate.................................. enabled MCS-29 Rate.................................. enabled MCS-30 Rate.................................. enabled MCS-31 Rate.................................. enabled Client Network Preference....................... defaultPress Enter to continue or to abort

AP ConfigCisco AP Identifier.............................. 6Cisco AP Name.................................... AP7c0e.cefb.97d0Country code..................................... Multiple Countries : SE,USRegulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-ABEAP Country code.................................. US - United StatesAP Regulatory Domain............................. -ASwitch Port Number .............................. 1MAC Address...................................... 7c:0e:ce:fb:97:d0IP Address Configuration......................... DHCPIP Address....................................... 192.168.0.158IP NetMask....................................... 255.255.255.0Gateway IP Addr.................................. 192.168.0.50NAT External IP Address.......................... NoneCAPWAP Path MTU.................................. 1485DHCP Release Override............................ Disabled Telnet State..................................... Globally DisabledSsh State........................................ Globally DisabledCisco AP Location................................ default locationCisco AP Floor Label............................. 0Cisco AP Group Name.............................. default-groupPrimary Cisco Switch Name........................

--More or (q)uit current module or to abortPrimary Cisco Switch IP Address.................. Not ConfiguredSecondary Cisco Switch Name...................... Secondary Cisco Switch IP Address................ Not ConfiguredTertiary Cisco Switch Name....................... Tertiary Cisco Switch IP Address................. Not ConfiguredAdministrative State ............................ ADMIN_ENABLEDOperation State ................................. REGISTEREDMirroring Mode .................................. DisabledAP Mode ......................................... LocalPublic Safety ................................... Disabled ATF Mode: ....................................... DisableAP SubMode ...................................... Not ConfiguredRogue Detection ................................. EnabledRemote AP Debug ................................. DisabledLogging trap severity level ..................... emergenciesLogging syslog facility ......................... systemS/W Version .................................... 8.5.103.0Boot Version ................................... 15.2.4.0Mini IOS Version ................................ 0.0.0.0Stats Reporting Period .......................... 180Stats Collection Mode ........................... normalRadio Core Mode ................................. DisabledLED State........................................ Enabled

--More or (q)uit current module or to abortPoE Pre-Standard Switch.......................... DisabledPoE Power Injector MAC Addr...................... DisabledPower Type/Mode.................................. DC / Full PowerNumber Of Slots.................................. 2 AP Model......................................... AIR-CAP3702I-A-K9AP Image......................................... C3700-K9W8-MIOS Version...................................... 15.3(3)JF$Reset Button..................................... EnabledAP Serial Number................................. FTX1832R34MAP Certificate Type.............................. Manufacture InstalledAP Lag Status ................................... DisableAP User Mode..................................... AUTOMATICAP User Name..................................... CiscoAP Dot1x User Mode............................... Not ConfiguredAP Dot1x User Name............................... Not ConfiguredCisco AP system logging host..................... 255.255.255.255AP Core Dump Config.............................. DisabledAP Up Time....................................... 3 days, 00 h 26 m 22 sAP LWAPP Up Time................................. 3 days, 00 h 24 m 23 sJoin Date and Time............................... Tue Sep 19 12:27:40 2017Join Taken Time.................................. 0 days, 00 h 01 m 58 s

Attributes for Slot 0

--More or (q)uit current module or to abort Radio Type................................... RADIO_TYPE_80211n-2.4 Administrative State ........................ ADMIN_ENABLED Operation State ............................. UP Mesh Radio Role ............................. ACCESS Radio Role .................................. Client Serving (Local) CellId ...................................... 0

Station Configuration Configuration ............................. AUTOMATIC Number Of WLANs ........................... 3 Medium Occupancy Limit .................... 100 CFP Period ................................ 4 CFP MaxDuration ........................... 60 BSSID ..................................... f0:7f:06:02:34:40 Operation Rate Set 11000 Kilo Bits.......................... MANDATORY 12000 Kilo Bits.......................... SUPPORTED 18000 Kilo Bits.......................... SUPPORTED 24000 Kilo Bits.......................... SUPPORTED 36000 Kilo Bits.......................... SUPPORTED 48000 Kilo Bits.......................... SUPPORTED 54000 Kilo Bits.......................... SUPPORTED MCS Set

--More or (q)uit current module or to abort MCS 0.................................... SUPPORTED MCS 1.................................... SUPPORTED MCS 2.................................... SUPPORTED MCS 3.................................... SUPPORTED MCS 4.................................... SUPPORTED MCS 5.................................... SUPPORTED MCS 6.................................... SUPPORTED MCS 7.................................... SUPPORTED MCS 8.................................... SUPPORTED MCS 9.................................... SUPPORTED MCS 10................................... SUPPORTED MCS 11................................... SUPPORTED MCS 12................................... SUPPORTED MCS 13................................... SUPPORTED MCS 14................................... SUPPORTED MCS 15................................... SUPPORTED MCS 16................................... SUPPORTED MCS 17................................... SUPPORTED MCS 18................................... SUPPORTED MCS 19................................... SUPPORTED MCS 20................................... SUPPORTED MCS 21................................... SUPPORTED MCS 22................................... SUPPORTED

--More or (q)uit current module or to abort MCS 23................................... SUPPORTED MCS 24................................... DISABLED MCS 25................................... DISABLED MCS 26................................... DISABLED MCS 27................................... DISABLED MCS 28................................... DISABLED MCS 29................................... DISABLED MCS 30................................... DISABLED MCS 31................................... DISABLED Beacon Period ............................. 100 Fragmentation Threshold ................... 2346 Multi Domain Capability Implemented ....... TRUE Multi Domain Capability Enabled ........... TRUE Country String ............................ US

Multi Domain Capability Configuration ............................. AUTOMATIC First Chan Num ............................ 1 Number Of Channels ........................ 11

MAC Operation Parameters Configuration ............................. AUTOMATIC Fragmentation Threshold ................... 2346

--More or (q)uit current module or to abort Packet Retry Limit ........................ 64

Tx Power Num Of Supported Power Levels ............. 8 Tx Power Level 1 .......................... 23 dBm Tx Power Level 2 .......................... 20 dBm Tx Power Level 3 .......................... 17 dBm Tx Power Level 4 .......................... 14 dBm Tx Power Level 5 .......................... 11 dBm Tx Power Level 6 .......................... 8 dBm Tx Power Level 7 .......................... 5 dBm Tx Power Level 8 .......................... 2 dBm Tx Power Configuration .................... CUSTOMIZED Current Tx Power Level .................... 6 Tx Power Assigned By ...................... User

Phy OFDM parameters Configuration ............................. CUSTOMIZED Current Channel ........................... 6 Channel Assigned By ....................... User Extension Channel ......................... NONE Channel Width.............................. 20 Mhz Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11

--More or (q)uit current module or to abort TI Threshold .............................. -50 DCA Channel List........................... Global Legacy Tx Beamforming Configuration ....... CUSTOMIZED Legacy Tx Beamforming ..................... ENABLED Antenna Type............................... INTERNAL_ANTENNA Internal Antenna Gain (in .5 dBi units).... 8 Diversity.................................. DIVERSITY_ENABLED 802.11n Antennas A....................................... ENABLED B....................................... ENABLED C....................................... ENABLED D....................................... ENABLED

Performance Profile Parameters Configuration ............................. CUSTOMIZED Interference threshold..................... 10 % Noise threshold............................ -70 dBm RF utilization threshold................... 80 % Data-rate threshold........................ 1000000 bps Client threshold........................... 12 clients Coverage SNR threshold..................... 15 dB Coverage exception level................... 25 % Client minimum exception level............. 3 clients

--More or (q)uit current module or to abort Rogue Containment Information Containment Count............................ 0

CleanAir Management Information CleanAir Capable......................... Yes CleanAir Management Administration St.... Enabled CleanAir Management Operation State...... Down Rapid Update Mode........................ Off Spectrum Expert connection............... Enabled CleanAir NSI Key....................... 1FF55FBB59179C03F962FD0895354C68 Spectrum Expert Connections counter.... 0 CleanAir Sensor State.................... Configured

Radio Extended Configurations Beacon period.............................. 100 milliseconds Beacon range............................... AUTO Multicast buffer........................... AUTO Multicast data-rate........................ AUTO RX SOP threshold........................... AUTO CCA threshold.............................. AUTO

Attributes for Slot 1 Radio Type................................... RADIO_TYPE_80211ac-5

--More or (q)uit current module or to abort Radio Subband................................ RADIO_SUBBAND_ALL Administrative State ........................ ADMIN_ENABLED Operation State ............................. UP Mesh Radio Role ............................. ACCESS Radio Role .................................. Client Serving (Local) CellId ...................................... 0

Station Configuration Configuration ............................. AUTOMATIC Number Of WLANs ........................... 3 Medium Occupancy Limit .................... 100 CFP Period ................................ 4 CFP MaxDuration ........................... 60 BSSID ..................................... f0:7f:06:02:34:40 Operation Rate Set 12000 Kilo Bits.......................... MANDATORY 18000 Kilo Bits.......................... SUPPORTED 24000 Kilo Bits.......................... SUPPORTED 36000 Kilo Bits.......................... SUPPORTED 48000 Kilo Bits.......................... SUPPORTED 54000 Kilo Bits.......................... SUPPORTED MCS Set MCS 0.................................... DISABLED

--More or (q)uit current module or to abort MCS 1.................................... SUPPORTED MCS 2.................................... SUPPORTED MCS 3.................................... SUPPORTED MCS 4.................................... SUPPORTED MCS 5.................................... SUPPORTED MCS 6.................................... SUPPORTED MCS 7.................................... SUPPORTED MCS 8.................................... SUPPORTED MCS 9.................................... SUPPORTED MCS 10................................... SUPPORTED MCS 11................................... SUPPORTED MCS 12................................... SUPPORTED MCS 13................................... SUPPORTED MCS 14................................... SUPPORTED MCS 15................................... SUPPORTED MCS 16................................... SUPPORTED MCS 17................................... SUPPORTED MCS 18................................... SUPPORTED MCS 19................................... SUPPORTED MCS 20................................... SUPPORTED MCS 21................................... SUPPORTED MCS 22................................... SUPPORTED MCS 23................................... SUPPORTED

--More or (q)uit current module or to abort MCS 24................................... DISABLED MCS 25................................... DISABLED MCS 26................................... DISABLED MCS 27................................... DISABLED MCS 28................................... DISABLED MCS 29................................... DISABLED MCS 30................................... DISABLED MCS 31................................... DISABLED 802.11ac MCS Set Nss=1: MCS 0-9 .......................... SUPPORTED Nss=2: MCS 0-9 .......................... SUPPORTED Nss=3: MCS 0-9 .......................... SUPPORTED Nss=4: MCS 0-7 .......................... SUPPORTED Beacon Period ............................. 100 Fragmentation Threshold ................... 2346 Multi Domain Capability Implemented ....... TRUE Multi Domain Capability Enabled ........... TRUE Country String ............................ US

Multi Domain Capability Configuration ............................. AUTOMATIC First Chan Num ............................ 36 Number Of Channels ........................ 4


MAC Operation Parameters Configuration ............................. AUTOMATIC Fragmentation Threshold ................... 2346 Packet Retry Limit ........................ 64

Tx Power Num Of Supported Power Levels ............. 8 Tx Power Level 1 .......................... 23 dBm Tx Power Level 2 .......................... 20 dBm Tx Power Level 3 .......................... 17 dBm Tx Power Level 4 .......................... 14 dBm Tx Power Level 5 .......................... 11 dBm Tx Power Level 6 .......................... 8 dBm Tx Power Level 7 .......................... 5 dBm Tx Power Level 8 .......................... 2 dBm Tx Power Configuration .................... CUSTOMIZED Current Tx Power Level .................... 8 Tx Power Assigned By ...................... User

Phy OFDM parameters Configuration ............................. CUSTOMIZED Current Channel ........................... 149

--More or (q)uit current module or to abort Channel Assigned By ....................... User Extension Channel ......................... NONE Channel Width.............................. 20 Mhz Allowed Channel List....................... 36,40,44,48,52,56,60,64,100, ......................................... 104,108,112,116,132,136,140, ......................................... 149,153,157,161,165 TI Threshold .............................. -50 DCA Channel List........................... Global Legacy Tx Beamforming Configuration ....... CUSTOMIZED Legacy Tx Beamforming ..................... ENABLED Antenna Type............................... INTERNAL_ANTENNA Internal Antenna Gain (in .5 dBi units).... 8 Diversity.................................. DIVERSITY_ENABLED 802.11n Antennas A....................................... ENABLED B....................................... ENABLED C....................................... ENABLED D....................................... ENABLED

Performance Profile Parameters Configuration ............................. CUSTOMIZED Interference threshold..................... 10 % Noise threshold............................ -70 dBm

--More or (q)uit current module or to abort RF utilization threshold................... 80 % Data

Date post:	01-May-2018
Category:	Documents
Upload:	vuhanh
View:	311 times
Download:	15 times

Interoperability Report - Site root - AscomPartnerWeb Report Ascom i62 Cisco WLC WLC controller...

Documents