Intruder and blast resistant security doors
SECUR-DOR
TESTED TO
BS EN 1627:2011
CERTIFIED BY
Warrington Exova Certisecure STS 202
PAS 24
(SECUR-DOR SD4)
BS EN 13124-2:2004EXR2
EXPLOSIVERESISTANT
INTRUDER RESISTANT
We offer three versions – each providing increased security (latched or unlatched):
Security DoorTested to
STS202 BR2 & PAS24
protect low to medium risk properties from
determined opportunist attempts at forced entry using a variety of hand
tools. They are particularly suitable as apartment
doors for residential and social housing.
Security DoorTested to
STS202 BR3Protect medium risk
residential or commercial properties from attempts at forced entry, with little
regard for noise, using heavy hand tools.
Security and Blast Door
Tested to ENV 1627 Level 4
Protect medium to high risk properties from
experienced attempts at forced entry, regardless
of noise, using heavy hand and battery tools or
explosives.
Certified Steel Security DoorsOur Security Doors been tested to and passed Warrington Exova Certisecure STS 202 and PAS 24 standards.
Our Security Doors have also been tested to and passed BS EN 1627:2011 and European Security Standard DD ENV 1627:1999.
SECUR-DOR
Did you know we send out touch up kits with every door?
> VERSIONS
> DOOR LEAF
Production Sizes: All SECUR-DOR doors are custom made. The maximum size varies according to fire rating as shown below for Mild Steel and 316 or 304 Stainless Steel.
Single Doors Latched(Single Swing)
Max Width mm 1300 1300 1250
Max Height mm 2800 2800 2800
Double Doors (Single Swing - Latched or unlatched, equal or unequally split)
Max Width mm 2700 2700 2600
Max Height mm 2800 2800 2800
Thickness: mm 48 55 48
Material: 1.5mm corrosion resistant Zintec/Aluzinc sheets as
standard
2mm corrosion resistant Zintec/Aluzinc sheets as
standard
1.5mm corrosion resistant Zintec/Aluzinc sheets as
standard
Infill: Filled with mineral wool and integral steel
stiffeners.
Filled with mineral wool and integral steel
stiffeners.
Solid timber cored with internal stainless steel steel anti-attack skin
Construction: Doorblade manufactured from two 1.5mm sheets lockformed together, by bonding two steel skins
around a rigid core. A total steel armour thickness of
3 - 4mm.
Doorblade manufactured from two 2mm sheets
lockformed together, by bonding two steel skins
around a rigid core. A total steel armour thickness of
4mm. Fitted with anti-tamper hinges.
Doorblade manufactured from two 1. 5mm sheets
lockformed together, by bonding two steel
skins around a rigid core. Additionally fitted with a 1.5mm stainless steel
sheet to the internal face of the outer skin and a solid timber core. Fitted with a full length continuous
hinge. A total steel armour thickness of 4.5mm. Fitted
with integral lock box.
> FINISHES
Polyester PowderCoated from Standard Colour Range
Standard
Polyester PowderCoated from Non-Standard Colour Range
Unfinished forsite finishing
Optional
All of our doors are made to measure!
ORDER HOTLINE: 00000 0000000 e: [email protected] www.customerwebaddress.com
Standard: 15mm rebated(DDA compliant)
Optional: 5mm driveable
(DDA compliant)
Permitted panel sizes: Max Width mm 610
Max Height mm 1854
Max Area m2 0.4
Standard glazings available: Other configurations and sizes available – please contact the Sales Office.
11.5mm laminated
(wired or clear)
> VISION PANELS
Standard
457mm dia305mm dia 254x254mm 254x559mm
> DOOR FRAME
> THRESHOLD
Construction: Material: Folded and welded from 1.6mm Zintec/Aluzinc.
Folded and welded from 2mm Zintec/Aluzinc.
Folded and welded from 3mm Zintec/Aluzinc.
Sub-Frame: Fully welded, variable sub-frame supplied as standard to
accommodate site tolerance of -0/+30mm.
The sub-frame providing additional protection to the
fixings against jemmys.
Folded and welded from 2mm Zintec/Aluzinc. Fully welded, variable sub-frame supplied
as standard to accommodate site tolerance of -0/+30mm.
Complete with Anti-Crush plate. The sub-frame providing
additional protection to the fixings against jemmys.
Specially modified, variable sub-frame supplied as standard to accommodate site tolerance of -0/+30mm. The sub-frame
providing additional protection to the fixings against jemmys.
Fixings: Four specially modified Class 13 stainless steel hinges with four security dog bolts for security.
Four Class 13 stainless steel dog bolt hinges recessed and specially modified to prevent pin extraction. Plus two solid
ball round dog bolts to increase resistance to prising
Stainless steel dog bolted continuous hinges for additional
security.
Infill: Mineral wool Mineral wool
Profile: (see diagrams below) A, B, C A, B, C, D C, D
TYPE BTYPE A TYPE C TYPE D
100
15
113,6
6,34
Only available on SECUR-DOR2 PAS 24
ORDER HOTLINE: 00000 0000000 e: [email protected] www.customerwebaddress.com
Individual specifications may vary as we conduct a policy of continuous product development.
> SECURE LOCKING
> THERMAL VALUES
> APPLICATIONS
> TESTING
Locking: PAS 24Fitted with high security Deadlock or
Sashlock (c/w lever handles or pull handle) & double europrofile cylinder and fitted
with TS007 security escutcheons.
STS202 (BR2) Fitted with a minimum of two high security
locks;1 no Securefast C EN grade 7 security
sashlock and lever handle, (SA 222 50SS R/7) double europrofile cylinder and fitted with TS007 security escutcheons fitted to
the centre door position1 no Securefast C EN grade 7 security deadlock, (SA21250 SS R /7) double
europrofile cylinder and fitted with TS007 security escutcheons fitted to the lower
quarter of the door leaf.
Fire Escape DoorsAlternatively the doors can be fitted with 3 point heavy duty panic escape hardware to offer means of escape, which is accepted
by the Secure by Design scheme.
Fire Escape Doors are fitted with a 1.2mm internal skin to resist drill attack.
Note: Taller doors may require a third, additional, lock.
3 no individual high security locks for enhanced security
High Security triple point high security sashlock, Securefast, with High Security
cylinders and anti-jemmy escutcheon protecting against snapping attack.
Lock is anti-drill and pattern protected to reduce the risk of key copying. Doors
are fitted with Exidor tower bolts.
Alternatively doors can be fitted with with three point heavy duty Panic
Hardware for Fire Escape but must be fitted with a Locking Box to prevent Drill
Attack.
Double doors are fitted with heavy duty tower bolts to inactive leaf.
A centre High Security Sashlock combined with two similar Deadlocks in the upper and lower quarters of the door. All locks fitted with anti-jemmy
escutcheon and welded shroud. Locks are anti-drill and pattern protected
to reduce risk of key copying. MICO TINDALL and Surelock McGill hardware
can also be used. Doors are fited with Exidor tower bolts.
Alternatively high security multi-point heavy duty panic hardware for fire
escapes.
Double doors are fitted with heavy duty tower bolts to inactive leaf..
Obtainable thermal values with infill as detailed:
2.4 w/m2k 2.6 w/m2k 2.9 w/m2k
Duty: Light commercial and perimeter security.
Protection from a determined attack, with some preparation and a number
of tools where the attacker is willing to make some, but not prolonged, noise.
Note: All duty recommendations assume the doors are used in
conjunction with othercomparable levels of security at
windows, etc.
The SD2 door can offer up to 120min. fire rating if fitted with appropriate
ironmongery
Medium risk residential and commercial properties which may be obscured from
view.
Protection from a deliberate forced entry of a well protected property using a wide variety of tools with little regard
for noise.
Note: All duty recommendations assume the doors are used in
conjunction with other comparable levels of security at windows etc.
The SD3 door can offer 120min. fire rating if fitted with appropriate
ironmongery.
Heavy duty and vulnerable properties, probably with a prior record of attempts
at forced entry.
Protection from experienced attempts at forced entry of commercial properties
with no regard for noise.
Further the door is suitable for protection against attempted entry by
explosive blasts.
Note: All duty recommendations assume the doors are used in
conjunction with other comparable levels of security at windows, etc.
Security: These doors achieve a pass to the following: PAS24 and STS202 (BR2). Both of which are accepted by Secure
by Design.BS EN 1627 level 2
Tests involve a determined attack over a period of 15mins. using tools
including screwdriver, 300mm. lever, and hammer.
When fitted with Vision Panels the door can only be offered to PAS24 rating.
The SD2 holds Secure by Design certification.
These doors achieve a pass to the following: STS202 (BR3) which is
accepted by Secure by Design. BS1627 level 3
Tests involves a determined attack over a period of 20mins. using tools
including hand hammer, hand drill, and crowbar.
Tested to BS 1627 level 4The test involves a determined attack
over a period of 30mins. using a selection of hand and battery tools
including club hammer, cordless drill, cold chisel and axe.
Blast: N/A N/A SD4 doors have been tested and passed EXR2 of BS EN 13124-2, Explosion Resistance standard, with explosive
blasts using plastic explosives.
