Iphone4 Unlock dog
Use Manual
This instrument repair, you can unlock iPhone4 phone, change the serial number,change
IMEI, solution ID Lock, change the country, change colors, fix 3194 error,"Your iPhone
has problems", "needs to be replaced," and other failures.
Imei check : http://iphoneimei.info/
.
If unlock,must have unlock imei and sn write this to phone then unlock,phone must first change
cpu to 8824,,change flash files to 0049 files flash
Tips:
Do not use this tool application violations, please comply with local laws.
Not to be a normal phone or water machine repaired, the price could not agree to modify the customer's
serial number, so that the customer's phone prompts you IPHONE problem.。
If unlock,must have unlock imei and sn write this to phone then unlock,phone must first change
cpu to 8824,,change flash files to 0049 files flash
Necessary software: ITOOL, Phone Tool 1.08
Necessary hardware (achieve change imei conditions, showing "problematic", repair demon
machine condition): iphone4 phone must be 8824 no baseband empty cpu, fonts must have the
underlying data write (Universal Data) small font (0049)
Operating Instructions:
1, first dongle plugged into the computer above (Note: dongle is driverless dongle, no need to install
driver), and then install the software on the desktop shortcut will produce two are:
The first step then install PL2303 driver (if the computer has been installed you need to install);
Software Driver position:C:\Program Files\ITool\User&Driver\PL-2303 Drivers for Windows,
This driver supports - Windows 98SE,
- Windows ME,
- Windows 2000 SP4,
- Windows XP SP2,
- Windows Server 2003 (32 bit),
- Windows Vista (32 & 64 bit),
- Windows Server 2008 (32 & 64 bit),
- Windows 7 (32 & 64 bit))
After the driver installation click on the desktop "My Computer" - right - "Properties" - "Device Manager" -
"Port" If the following screen appears proved already installed driver (if you need to reinstall display a question
mark), and then proceed to the next :
Step Open the software "ITOOL" appears at the interface as shown below:
Then click on the corner of ,Activated, this point does not matter, internal
testing, does not close, then the next step,
Step Three: Then put your phone and computer using your cable connection our engineering (computer requires
installation itunes, if the computer has installed 91 mobile assistant general have installed itunes), if the
computer has installed, there will be prompt box "" appears, if not installed, it does not have this prompt, you
must install the Astoria assistant or 91 assistants, and then put the phone into dfu mode (hold down the home
button and the power button, such as a black screen after 5 seconds, release the power button, hold the home do
not release, over 10 seconds or so the software will prompt has entered dfu mode (note the computer screen
right thunderous sound and tips), then "ITOOL" software will find being in dfu mode iphone4 , then click
Testmode, software progress bar will move forward, if successful, the phone within 2 minutes into the purple
screen mode.
If the progress bar finish, the phone has been in the black, purple, or other non-screen mode, it
would need to force off the phone (home + power button long press 10 seconds), re-enter dfu mode, run
again Testmod progress bar to enter purple screen mode!
Then need to wait for about 10 seconds or so, if the phone does not appear purple screen, you
need to re-enter DFU mode operation again until well into the purple screen, as shown below:
(connect cable first in DFU,then button TestNode in pueple screen.)
Step Four: phone into a purple screen mode, then click on "ReadData", after waiting a few seconds, the
software will show your current phone's hardware information, where SN is the serial number of your phone,
check the "SN", will your phone imei corresponding serial number filled in. (check model, area code,
motherboard information and so can be modified), the country code and then click on "WritData", as shown in
the second figure; you will prompt the software below see the "finished", that means changes are complete.
Then exit this software to run a second imei software modifications.
Note: At this point can not click "RebootPhone", if this time click on the phone will automatically exit
purple screen mode to normal mode, the next step can not be carried imei repair.
Step Five: Run the "Phone Tool", the software will self-test as shown below:
Select PL2303 port on your computer properties - hardware manager-com communication ports can view the
specific port; painted red circle click, select Show serial port, the other does not matter, just click the OK button
below:
. Click OK, and enter the next step:
Then click below Button to enter the next step:
Select the upper-left corner "Modes" button, select the bottom "AT Terminal"
The following screen appears, and then click on the first line inside the input BPC "SEND",
This step is important
Wait out Uart to BB Test;
Again select the upper left corner "Modes" button, as shown below select "Security" button to enter the next
step
Select Advanced, enter the next step, as shown:
The second point Personalization Programing (red circle)
Signing keys Select 1024 that
You need to modify the input into imei, last digit is a check digit, the software will automatically populate.
(Be sure to check imei entered correctly)(A small font underlying data can be rewritten only once, you need to
re-program the need to rewrite the underlying data can be re-flashed or change new flash,files )
Click Generate and program traget, then Excute, you will see output information to complete imei rewritten,
disconnect the phone, Success!
Remember: (a small font underlying data can be rewritten only once, you need to re-program the need to
rewrite the underlying data can be re-flashed)
Imei check : http://iphoneimei.info/
What is DFU mode used for?
The primary reason people need to access DFU mode on their iPhone is to change the firmware
on the device. This can serve to downgrade to a prior iPhone firmware and operating system,
or to use a custom firmware that is required for a jailbreak or SIM unlock. For instance, if
you got the iPhone OS 4 download installed and decided you would rather have a prior version
of the firmware on your iPhone, you would need to do this through DFU mode.
How to enter iPhone DFU mode
Connect the iPhone to your computer and launch iTunes
Turn the iPhone off (hold down the power button at the top of the iPhone)
Hold down the sleep/power button and home button together for exactly 10 seconds, then release
the power button
Continue to hold down the Home button until a message appears in iTunes telling you an iPhone
in recover mode has been detected
=========================================
This is how to achieve DFU mode. You can do it on every phone:
Method 1)
Attach the phone to the pc
Turn the phone off
Hold power and home together for *exactly* 10 seconds
Release power but keep holding home until the pc beeps as a USB device is recognized.
At no point will the display come on. Now your restore should work.
Having problems? Try adjusting the 10 seconds to be slightly less like 9 seconds, then 8, then
7. It’s a tricky timing but you will eventually get it.
Method 2)
Hook up the phone powered on to the PC
Now hold home / power until the phone turns off and keep holding for 10 seconds. If the phone
ever turns on during this phase,start over and hold for less time.
Now release power and continue holding home until the PC recognizes the phone.
I don’t like this method as much because there are “rumors” that it may cause some 1604
errors in the restore. I am not convinced of that though.
Method 3)
Attach the phone to the pc
Turn the phone off
Press and hold power. Keep holding power. As soon as you see display on the screen of any sort
press and hold home.
Hold power and home together for *exactly* 10 seconds
Release power but keep holding home until the pc beeps as a USB device is recognized.
At no point will the display come on. Now your restore should work.
Having problems? Try adjusting the 10 seconds to be slightly less like 9 seconds, then 8, then
7. It’s a tricky timing but you will eventually get it.
=========================================
Exit DFU mode on iPhone
The simplest way to exit out of DFU mode is to hold down the Home and sleep/power buttons on
the iPhone while connected to iTunes. Then just hit the power button as and this should reboot
the device as usual.