| Date post: | 16-Jul-2015 |
| Category: |
Documents |
| Upload: | ajay-padia |
| View: | 137 times |
| Download: | 3 times |
of 77
Fittings
ASSEMBLY INSTRUCTIONAssembly instructions according to DIN 3859-2 In order to ensure proper screwed pipe connections, several basic prerequisites must be met in the assembly of all screw connection systems. Improper assembly may lead to malfunctions and impair safety.
Preparation of Pipes Saw off pipe at a right angle. Deviation of angle pipe axis of up to is permissible. Do not use a pipe cutter!
Lightly de burr pipe in the inside and outside of the cut edges. Bevel angles of up to 0.2 x 45 is permissible. Remove chips and particles.
For pipe bends, the minimum height from the straight pipe end to the bending radius must be noted. This must be at least twice the height of the union nut.
2
ASSEMBLY INSTRUCTIONAssembly of Cutting Screw Connection Pipes of rustproof steel must be pre-assembled in hardened pre-assembly connection pieces or the corresponding devices. This can also be recommended for serial assembly using components of other materials.
Assembly with Hardened pre-assembly connection piece Lightly grease the threads of the union nut, thread and cone of the pre-assembly connection piece and cutting ring, using, for example anti seize agent
Side union nut and cutting ring onto the pipe. Ensure that the cutting ring is positioned correctly (see drawing below).
Screw the union nut onto the pre-assembly connection piece as far as possible by hand. At the same time, press the pipe against the stop. As soon as the cutting ring has cut into the pipe, the tightening moment will increase noticeably. A flag at the union nut facilitates the observation of the necessary revolutions. Tighten union nut using a wrench by approx. 1 1/4 revolution. Important: Do not turn the pipe with the nut!
3
ASSEMBLY INSTRUCTIONCheck whether a visible collar has formed on the pipe in front of the (first) cutting edge.
Final assembly in screwed connection piece Insert the pre-assembled pipe into the screwed connection piece. Tighten union nut approx. revolution beyond the point at which the tightening moment increases noticeably, holding the screwed connection piece with a wrench.
4
BITE TYPE FITTINGS - SPECIFICATION
5
PORT TAPING FOR TUBE FITTINGS
6
TUBE SYSTEM DATA FOR FITTINGS
7
G - UNIONS1
S2
J.J.
I1 L1
Series
Tube OD4 6 8 10 12 6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
Part No.G - 4LL G - 6LL G - 8LL G - 10LL G - 12LL G - 6L G - 8L G - 10L G - 12L G - 15L G - 18L G - 22L G - 28L G - 35L G - 42L G - 6S G - 8S G - 10S G - 12S G - 14S G - 16S G - 20S G - 25S G - 30S G -38S
Pressure
S19 11 12 14 17 12 14 17 19 24 27 32 41 46 55 14 17 19 22 24 27 32 41 46 55
S210 12 14 17 19 14 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
L131 32 35 35 35 39 40 42 43 46 48 52 54 63 66 45 47 49 51 57 57 66 74 80 90
l112 9 12 12 11 10 11 13 14 16 16 20 21 20 21 16 18 17 19 22 21 23 26 27 29
LL Very Light
N.P. 100
N.P. 250
L Light
N.P. 160
N.P. 100
N.P. 630
S Heavy
N.P. 400
N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.8
W - UNION ELBOWS3 S2
J.J.
I2 L2
Series
Tube OD4 6 8 10 12 6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
Part No.W - 4LL W - 6LL W - 8LL W - 10LL W - 12LL W - 6L W - 8L W - 10L W - 12L W - 15L W - 18L W - 22L W - 28L W - 35L W - 42L W - 6S W - 8S W - 10S W - 12S W - 14S W - 16S W - 20S W - 25S W - 30S W -38S
Pressure
S39 11 12 14 17 12 14 17 19 19 24 27 36 41 50 14 17 19 20 22 24 27 36 41 50
S210 12 14 17 19 14 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
L221 21 23 24 25 27 29 30 32 36 40 44 47 56 63 31 32 34 38 40 43 48 54 62 72
l211 9.5 11.5 12.5 13 12 14 15 17 21 23.5 27.5 30.5 34.5 40 16 17 17.5 21.5 22 24.5 26.5 30 35.5 41
LL Very Light
N.P. 100
N.P. 250
L Light
N.P. 160 N.P. 100
N.P. 630
S Heavy
N.P. 400 N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.9
T - UNION TEES3 S2
J.J.
I1 L2
SeriesLL Very Light
Tube OD4 6 8 10 12 6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
Part No.T - 4LL T - 6LL T - 8LL T - 10LL T - 12LL T - 6L T - 8L T - 10L T - 12L T - 15L T - 18L T - 22L T - 28L T - 35L T - 42L T - 6S T - 8S T - 10S T - 12S T - 14S T - 16S T - 20S T - 25S T - 30S T -38S
Pressure
S39 11 12 14 17 12 14 17 19 19 24 27 36 41 50 14 17 19 20 22 24 27 36 41 50
S210 12 14 17 19 14 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
L221 21 23 24 25 27 29 30 32 36 40 44 47 56 63 31 32 34 38 40 43 48 54 62 72
l211 9.5 11.5 12.5 13 12 14 15 17 21 23.5 27.5 30.5 34.5 40 16 17 17.5 21.5 22 24.5 26.5 30 35.5 41
N.P. 100
N.P. 250
L Light
N.P. 160 N.P. 100
N.P. 630
S Heavy
N.P. 400 N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
10
K - UNION CROSSS3
S2
J.J.
I2 L2
Series Tube ODLL Very Light 4 6 8 6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
Part No.K - 4LL K - 6LL K - 8LL K - 6L K - 8L K - 10L K - 12L K - 15L K - 18L K - 22L K - 28L K - 35L K - 42L K - 6S K - 8S K - 10S K - 12S K - 14S K - 16S K - 20S K - 25S K - 30S K - 38S
PressureN.P. 100
S39 9 12 12 12 14 17 19 24 27 36 41 50 12 14 17 17 19 24 27 36 41 50
S210 12 14 14 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
L221 21 23 27 29 30 32 36 40 44 47 56 63 31 32 34 38 40 43 48 54 62 72
l211 9.5 11.5 12.5 13 12 14 15 17 21 23.5 27.5 30.5 34.5 40 16 17 17.5 21.5 22 24.5 26.5 30
N.P. 250
L Light
N.P. 160
N.P. 100
N.P. 630
S Heavy
N.P. 400
N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.11
SV - BULKHEAD UNIONS1 S4 S2
J.J.
D I1 L1
M
L3
Series
Tube OD6 8 10 12
Part No.SV - 6L SV - 8L SV - 10L SV - 12L SV - 15L SV - 18L SV - 22L SV - 28L SV - 35L SV - 42L SV - 6 S SV - 8 S SV - 10 S SV - 12 S SV - 14 S SV - 16 S SV - 20 S SV - 25 S SV - 30 S SV -38 S
Pressure
S117 19
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
S417 19 22 24 27 32 36 41 50 60 19 22 24 27 30 32 41 46 50 65
L122 23 25 25 27 30 33 35 40 42 27 28 31 31 35 35 39 44 48 53
I17 8 10 10 12 13.5 16.5 18.5 18.5 19 12 13 14.5 14.5 17 16.5 17.5 20 21.5 22
L342 42 43 44 46 49 51 52 58 59 44 44 46 47 50 50 55 59 64 68
I327 27 28 29 31 32.5 34.5 35.5 36.5 36 29 29 29.5 30.5 32 31.5 33.5 35 37.5 37
N.P. 250
22 24 27 32 36 41 50 60 19 22
L Light
15 18 22 28 35 42 6 8 10 12
N.P. 160
N.P. 100
N.P. 630
24 27 30 32
S Heavy
14 16 20 25 30 38
N.P. 400
41 46 50 65
N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.12
WSV - BULKHEAD UNION ELBOWS3 S4 S2
J.J. L2 I2
D
M
I5
I3 L3
Se- Tube ries OD6 8 10 12 L Light 15 18 22 28 35 42 6 8 10 12 S Heavy 14 16 20 25 30 38
Part No.WSV - 6L WSV - 8L WSV - 10L WSV - 12L WSV - 15L WSV - 18L WSV - 22L WSV - 28L WSV - 35L WSV - 42L WSV - 6S WSV - 8S WSV - 10S WSV - 12S WSV - 14S WSV - 16S WSV - 20S WSV - 25S WSV - 30S WSV -38S
Pressure
S214 17
S312 12 14 17 19 24 27 36 41 50 12 14 17 17 19 24 27 36 41 50
S4*17 19 22 24 30 36 41 46 55 65 19 22 24 27 30 32 41 46 50 65
L227 29 30 32 36 40 44 47 56 63 31 32 34 38 40 43 48 54 62 72
I212 14 15 17 21 23.5 27.5 30.5 34.5 40 16 17 17.5 21.5 22 24.5 26.5 30 35.5 41
L342 42 43 44 46 49 51 52 58 59 44 44 46 47 50 50 55 59 64 68
I327 27 28 29 31 32.5 34.5 35.5 36.5 36 29 29 29.5 30.5 32 31.5 33.5 35 37.5 37
I514 17 18 20 23 24 30 34 39 43 17 18 20 21 23 24 30 34 39 43
d217 19 22 24 27 32 36 42 50 60 19 22 24 27 27 30 36 42 50 60
N.P. 250
19 22 27 32 36 41 50 60 17 19
N.P. 160
N.P. 100
N.P. 630
22 24 27 30
N.P. 400
36 46 50 60
N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
13
GE - MALE STUD COUPLING BSPP THREADS1 S2S2 S1
J.J.
G d3
J.J.
G
I
I
I1 L1L1
I1
BSPPSeries Tube OD4 6 8 10 12 6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
BSPTMale Thread G" Taper " Taper " Taper " Taper " Taper " " " " " " " 1" 1 " 1 " " " " " " " " 1" 1 " 1 "
Part No.GE - 4LLR GE - 6LLR GE - 8LLR GE - 10LLR GE - 12LLR GE - 6LR GE - 8LR GE - 10LR GE - 12LR GE - 15LR GE - 18LR GE - 22LR GE - 28LR GE - 35LR GE - 42LR GE - 6SR GE - 8SR GE - 10SR GE - 12SR GE - 14SR GE - 16SR GE - 20SR GE - 25SR GE - 30SR GE - 38SR
Pressure
S111 11 12 14 17 14 19 19 22 27 27 32 41 50 55 19 19 22 22 27 27 32 41 50 55
S210 12 14 17 19 14 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
L126 26 28 32 32 23 25 26 27 29 31 33 34 39 42 28 30 31 33 37 37 42 47 50 57
l116 14.5 16.5 21.5 20 8.5 10 11.5 12.5 14 14.5 16.5 17.5 17.5 19 13 15 15 17 19 18.5 20.5 23 23.5 26
I8 8 8 12 12 8 12 12 12 14 14 16 18 20 22 12 12 12 12 14 14 16 18 20 22
d314 18 18 22 26 26 32 39 49 55 18 18 22 22 26 26 32 39 49 55
LL Very Light
N.P. 100
N.P. 250
L Light
N.P. 160
N.P. 100
N.P. 630
S Heavy
N.P. 400
N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
14
GE - MALE STUD COUPLING BSPP THREAD WITH ELASTOMERIC SEALS1 S2
J.J.
G d3
I
I1 L1
Tube Series OD6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
Part No.GE - 6LR-ed GE - 8LR-ed GE - 10LR-ed GE - 12LR-ed GE - 15LR-ed GE - 18LR-ed GE - 22LR-ed GE - 28LR-ed GE - 35LR-ed GE - 42LR-ed GE - 6SR-ed GE - 8SR-ed GE - 10SR-ed GE - 12SR-ed GE - 14SR-ed GE - 16SR-ed GE - 20SR-ed GE - 25SR-ed GE - 30SR-ed GE - 38SR-ed
Male BSPP Thread G" " " " " " " 1" 1 " 1 " " " " " " " " 1" 1 " 1 "
Pressure
S114 19 19 22 27 27 32 41 50 55 19 19 22 22 27 27 32 41 50 55
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
L123 25 26 27 29 31 33 34 39 42 28 30 31 33 37 37 42 47 50 57
l18.5 10 11 12.5 14 14.5 16.5 17.5 17.5 19 13 15 15 17 19 18.5 20.5 23 23.5 26
I8 12 12 12 14 14 16 18 20 22 12 12 12 12 14 14 16 18 20 22
d714 19 19 22 27 27 32 40 40 55 19 19 22 22 27 27 32 40 50 55
N.P. 250
L Light
N.P. 160 N.P. 100
N.P. 630
S Heavy
N.P. 400 N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
15
WE - MALE ELBOWS3 S2S3 S2
J.J.I3
J.J.
I3I GI2 L2
I
GI2 L2
BSPPSeries Tube OD4 6 8 10 12 6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
BSPTMale PresThread G sure" Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " 1" 1 " 1 " " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " 1" 1 " 1 "
Part No.WE - 4LLR WE - 6LLR WE - 8LLR WE - 10LLR WE - 12LLR WE - 6LR WE - 8LR WE - 10LR WE - 12LR WE - 15LR WE - 18LR WE - 22LR WE - 28LR WE - 35LR WE - 42LR WE - 6SR WE - 8SR WE - 10SR WE - 12SR WE - 14SR WE - 16SR WE - 20SR WE - 25SR WE - 30SR WE - 38SR
S210 12 14 17 19 14 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
S311 11 12 14 17 12 14 17 19 19 24 27 36 41 50 14 17 19 20 22 24 27 36 41 50
L221 21 23 24 25 27 29 30 32 36 40 44 47 56 63 31 32 34 38 40 43 48 54 62 72
l211 9.5 11.5 12.5 13 12 14 15 17 21 23.5 27.5 30.5 34.5 40 16 17 17.5 21.5 22 24.5 26.5 30 35.5 41
I8 8 8 12 12 8 12 12 12 14 14 16 18 20 22 12 12 12 12 14 14 16 18 20 22
l317 17 20 23 23 20 26 27 28 34 36 26 30 34 39 26 27 28 28 32 32 26 30 34 39
LL Very Light
N.P. 100
N.P. 250
L Light
N.P. 160 N.P. 100
N.P. 630
S Heavy
N.P. 400 N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
16
TE - MALE BRANCH TEES3 S2
S3
S2
J.J.
J.J.
I3
I
I3
G
I
GI2 L2
I2 L2
BSPTTube Series OD4 6 8 10 12 6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
Part No.TE - 4LLR TE - 6LLR TE - 8LLR TE - 10LLR TE - 12LLR TE - 6LR TE - 8LR TE - 10LR TE - 12LR TE - 15LR TE - 18LR TE - 22LR TE - 28LR TE - 35LR TE - 42LR TE - 6SR TE - 8SR TE - 10SR TE - 12SR TE - 14SR TE - 16SR TE - 20SR TE - 25SR TE - 30SR TE - 38SR
Male Thread G" Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " 1" 1 " 1 " " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " 1" 1 " 1 "
Pressure
S210 12 14 17 19 14 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
S311 11 12 14 17 12 14 17 19 19 24 27 36 41 50 14 17 19 20 22 24 27 36 41 50
L221 21 23 24 25 27 29 30 32 36 40 44 47 56 63 31 32 34 38 40 43 48 54 62 72
l211 9.5 11.5 12.5 13 12 14 15 17 21 23.5 27.5 30.5 34.5 40 16 17 17.5 21.5 22 24.5 26.5 30 35.5 41
I8 8 8 12 12 8 12 12 12 14 14 16 18 20 22 12 12 12 12 14 14 16 18 20 22
l317 17 20 23 23 20 26 27 28 34 36 26 30 34 39 26 27 28 28 32 32 26 30 34 39
LL Very Light
N.P. 100
N.P. 250
L Light
N.P. 160 N.P. 100
N.P. 630
S Heavy
N.P. 400
N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.17
LE - MALE RUN TEES2 S3L3
S2 S3
J.J.I3L3 I3 I
J.J.
I
GI2 L2
GI2 L2
BSPPSeries Tube OD4 6 8 6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
BSPTMale BSPP Thread G" Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " 1" 1 " 1 " " Tapper " Tapper " Tapper " Tapper " Tapper " Tapper " 1" 1 " 1 "
Part No.LE - 4 L LR LE - 6 L LR LE - 8 L LR LE - 6 LR LE - 8 LR LE - 10 LR LE - 12 LR LE - 15 LR LE - 18 LR LE - 22 LR LE - 28 LR LE - 35 LR LE - 42 LR LE - 6SR LE - 8SR LE - 10SR LE - 12SR LE - 14SR LE - 16SR LE - 20SR LE - 25SR LE - 30SR LE - 38SR
Pressure
S210 12 14 14 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
S311 11 12 12 14 17 19 19 24 27 36 41 50 14 17 19 20 22 24 27 36 41 50
L221 21 23 27 29 30 32 36 40 44 47 56 63 31 32 34 38 40 43 48 54 62 72
l211 9.5 11.5 12 14 15 17 21 23.5 27.5 30.5 34.5 40 16 17 17.5 21.5 22 24.5 26.5 30 35.5 41
I8 8 8 8 12 12 12 14 14 16 18 20 22 12 12 12 12 14 14 16 18 20 22
l317 17 20 20 26 27 28 34 36 26 30 34 39 26 27 28 28 32 32 26 30 34 39
L338 38 43 47 55 57 60 70 76 70 77 90 102 57 59 62 66 72 75 74 84 96 111
LL Very Light
N.P. 100
N.P. 250
L Light
N.P. 160 N.P. 100
N.P. 630
S Heavy
N.P. 400 N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.18
EVGE-R-ed SWIVEL MALEBSPPS1 S2
J.J.
G d3
I
I1 L1
Series
Tube OD6 8 10 12
Part No.GE - 6LR-ed GE - 8LR-ed GE - 10LR-ed GE - 12LR-ed GE - 15LR-ed GE - 18LR-ed GE - 22LR-ed GE - 28LR-ed GE - 35LR-ed GE - 42LR-ed GE - 6SR-ed GE - 8SR-ed GE - 10SR-ed GE - 12SR-ed GE - 14SR-ed GE - 16SR-ed GE - 20SR-ed GE - 25SR-ed GE - 30SR-ed GE - 38SR-ed
Male BSPP Thread G" " " " " " " 1" 1 " 1 " " " " " " " " 1" 1 " 1 "
Pressure
S114 19
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
d1
l5
I8 12 12 12 14 14 16 18 20 22 12 12 12 12 14 14 16 18 20 22
d714 19 19 22 27 27 32 40 50 55 19 19 22 22 27 27 32 40 50 55
M12 X 1.5 24.5 M14 X 1.5 29.5 M16 X 1.5 27.5 M18 X 1.5 34.0 M22 X 1.5 M30 X 2 M36 X 2 M45 X 2 M52 X 2 M14 X 1.5 M18 X 1.5 M20 X 1.5 M24 X 1.5 M30 X 2 M36 X 2 M42 X 2 M52 X 2 32 32.5 35 42.5 46.5 27 32 34 37 43 48 51.0 60 M26 X 1.5 31.5
N.P. 250
19 22 27 27 32 41 50 55 19 19
L Light
15 18 22 28 35 42 6 8 10 12
N.P. 160
N.P. 100
M16 X 1.5 29.5
N.P. 630
22 22 27 27
S Heavy
14 16 20 25 30 38
M22 X 1.5 36.5
N.P. 400
32 41 50 55
N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
19
EVW - SWIVEL ELBOWL2 I2 S3 S2
J.J.
I5 S2 PRE INSTALLED D1 d1
Series
Tube OD6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
Part No.EVW - 6L EVW - 8L EVW - 10L EVW - 12L EVW - 15L EVW - 18L EVW - 22L EVW - 28L EVW - 35L EVW - 42L EVW - 6S EVW - 8S EVW - 10S EVW - 12S EVW - 14S EVW - 16S EVW - 20S EVW - 25S EVW - 30S EVW - 38S
Pressure S312 12 N.P. 250 14 17 19 N.P. 160 24 27 36 N.P. 100 41 50 12 14 N.P. 630 17 17 19 24 N.P. 400 27 36 N.P. 250 41 50
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
d1M12 X 1.5 M14 X 1.5 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M36 X 2 M45 X 2 M52 X 2 M14 X 1.5 M16 X 1.5 M18 X 1.5 M20 X 1.5 M22 X 1.5 M24 X 1.5 M30 X 2 M36 X 2 M42 X 2 M52 X 2
L227 29 30 32 36 40 44 47 56 63 31 32 4 38 40 43 48 54 62 72
I212 14 15 17 21 23.5 27.5 30.5 34.5 40 16 17 17.5 21.5 22 24.5 26.5 30 35.5 41
I526 27.5 29 30.5 33.5 36 39 43.5 54.5 60 27 29 32 33 36 37.5 44.5 50.5 56.5 67.5
D16 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
L Light
S Heavy
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
20
EVT - SWIVEL BRANCH TEEL2 I2 S3 S2
J.J.
I5 S2 PRE INSTALLED D1 d1
Series
Tube OD6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
Part No.EVT - 6L EVT - 8L EVT - 10L EVT - 12L EVT - 15L EVT - 18L EVT - 22L EVT - 28L EVT - 35L EVT - 42L EVT - 6S EVT - 8S EVT - 10S EVT - 12S EVT - 14S EVT - 16S EVT - 20S EVT - 25S EVT - 30S EVT - 38S
Pressure S312 12 N.P. 250 14 17 19 N.P. 160 24 27 36 N.P. 100 41 50 12 14 N.P. 630 17 17 19 24 N.P. 400 27 36 N.P. 250 41 50
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
d1M12 X 1.5 M14 X 1.5 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M36 X 2 M45 X 2 M52 X 2 M14 X 1.5 M16 X 1.5 M18 X 1.5 M20 X 1.5 M22 X 1.5 M24 X 1.5 M30 X 2 M36 X 2 M42 X 2 M52 X 2
L227 29 30 32 36 40 44 47 56 63 31 32 4 38 40 43 48 54 62 72
I212 14 15 17 21 23.5 27.5 30.5 34.5 40 16 17 17.5 21.5 22 24.5 26.5 30 35.5 41
I526 27.5 29 30.5 33.5 36 39 43.5 54.5 60 27 29 32 33 36 37.5 44.5 50.5 56.5 67.5
D16 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
L Light
S Heavy
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
21
EVL- SWIVEL RUN TEEL5 I5 S2 S3 S2
d1
D1
J.J.I2 L2
PRE INSTALLED
Series
Tube OD6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
Part No.EVL - 6L EVL - 8L EVL - 10L EVL - 12L EVL - 15L EVL - 18L EVL - 22L EVL - 28L EVL - 35L EVL - 42L EVL - 6S EVL - 8S EVL - 10S EVL - 12S EVL - 14S EVL - 16S EVL - 20S EVL - 25S EVL - 30S EVL - 38S
Pressure S312 12 N.P. 250 14 17 19 N.P. 160 24 27 36 N.P. 100 41 50 12 14 N.P. 630 17 17 19 24 N.P. 400 27 36 N.P. 250 41 50
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
d1M12 X 1.5 M14 X 1.5 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M36 X 2 M45 X 2 M52 X 2 M14 X 1.5 M16 X 1.5 M18 X 1.5 M20 X 1.5 M22 X 1.5 M24 X 1.5 M30 X 2 M36 X 2 M42 X 2 M52 X 2
L227 29 30 32 36 40 44 47 56 63 31 32 4 38 40 43 48 54 62 72
I212 14 15 17 21 23.5 27.5 30.5 34.5 40 16 17 17.5 21.5 22 24.5 26.5 30 35.5 41
I526 27.5 29 30.5 33.5 36 39 43.5 54.5 60 27 29 32 33 36 37.5 44.5 50.5 56.5 67.5
D16 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
L Light
S Heavy
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.22
SWVE - R - BANJO ELBOW MALE BSPP CUTTING FACE & PACKING RING SEALL2 S6 I2 S2 S3
L3
J.J.I3
I
G d3
Se- Tube ries OD4 LL Very Light 6 8 6 8 10 L Light 12 15 18 22 6 8 10 S Heavy 12 14 16 20
Part No.SWVE - 4LLR SWVE - 6LLR SWVE - 8LLR SWVE - 6LR SWVE - 8LR SWVE - 10LR SWVE - 12LR SWVE - 15LR SWVE - 18LR SWVE - 22LR SWVE - 6 SR SWVE - 8 SR SWVE - 10 SR SWVE - 12 SR SWVE - 14 SR SWVE - 16 SR SWVE - 20 SR
Male BSPP Thread G" " " " " " " " " Packing Ring " Packing Ring " " " " " " Packing Ring " Packing Ring
Pressure
L221
I211.5 10 11 10.5 13 14 15.5 19
I310 10 10 10 13 13 15 18
d3 S214.5 14.5 14.5 14.5 18.5 18.5 22.5 26.5 26 32 18.5 18.5 22.5 22.5 26.5 26 32 10 12 14 14 17 19 22 27 32 36 17 19 22 24 27 30 36
I6 6 6 6 9 9 9 11 11 13 9 9 9 9 11 11 13
L3 S3 S621 21 21 21 27 27 32 37 44 49 27 27 32 37 37 44 49 14 14 14 14 19 19 22 27 30 36 19 19 22 24 27 30 36 14 14 14 14 19 19 22 27 27 32 19 19 22 24 27 27 32
N.P. 40
22 23 25 28 29
N.P.100
30 34 37 42 30 30 32
20.5 21.5 25.5 15 15 16 17 20 24 13 13 15 18 18
N.P. 160
33 38 40 46
21.5 21.5 24.5 24
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.23
DSWV - R - THROTTLE FREE BANJO ELBOW MALE BSPP - METAL PACKING RING SEALL2 S6 I2 S2 S3
L3
J.J.I3S6
I
G d3
Series
Tube OD6 8 10
Part No.DSVW - 6LR DSVW - 8LR DSVW - 10LR DSVW - 12LR DSVW - 15LR DSVW - 18LR DSVW - 22LR DSVW - 28LR DSVW - 35LR DSVW - 42LR DSVW - 6SR DSVW - 8SR DSVW - 10SR DSVW - 12SR DSVW - 14SR DSVW - 16SR DSVW - 20SR DSVW - 25SR DSVW - 30SR DSVW - 38SR
Male BSPP PresL2 Thread G sure" " " " " " " 1" 1 " 1 " " " " " " " " 1" 1 " 1 " 250 N.P. 400 N.P. 100 N.P. 250 N.P. 27 29 30 33 37 38 45 48 57 63 31 31 35 35 41 41 49 55 63 72
I212.5 14.5 15.5 18 22 21.5 28.5 31.5 35.5 40 16.5 16.5 18.5 18.5 23 22.5 27.5 31 36.5 41
L324 30 30 37 42 46 58 64 76 85 30 30 37 37 42 46 58 64 76 85
I312 16 16 18 21 23 28 32 37 42 16 16 18 18 21 23 28 32 37 42
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
S318 22 22 27 32 36 46 50 60 70 22 22 27 27 32 36 46 50 60 70
S66 8 8 10 12 12 17 22 27 32 8 8 10 10 12 12 17 22 27 32
d314 18 18 22 26 26 32 39 49 55 18 18 22 22 26 26 32 39 49 55
I8 12 12 12 14 14 16 18 20 22 12 12 12 12 14 14 16 18 20 22
L Light
12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
S Heavy
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.24
GAI - R - FEMALE CONNECTOR - BSPPS1 S2
d1 d5
J.J.
I2 I5 L5
Series
Tube OD6 8 10
Part No.GAI - 6LR GAI - 8LR GAI - 10LR GAI - 12LR GAI - 15LR GAI - 18LR GAI - 22LR GAI - 28LR GAI - 35LR GAI - 42LR GAI - 6SR GAI - 8SR GAI - 10SR GAI - 12SR GAI - 14SR GAI - 16SR SWVE - 20SR GAI - 25SR GAI - 30SR GAI - 38SR
Female BSPP Thread d1" " " " " " " 1" 1 " 1 " " " " " " " " 1" 1 " 1 "
Pressure
d54 6
L534 39 40 41 46 47 52 55 63 65 41 41 43 43 50 50 56 62 69 74
I519 24 25 26 31 30.5 35.4 38 41 42.5 26 26 26.5 26.5 32 31.5 34.5 37.5 42 43.5
t212 17 17 17 20 20 22 24.5 26.5 28.5 17 17 17 17 20 20 22 24.5 26.5 28.5
S114 19 19 24 27 27 36 41 55 60 19 19 24 24 30 30 36 41 55 60
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
N.P. 250
8 10 12 15 19 24 30 36 4 5
L Light
12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
N.P. 160
N.P. 100
N.P. 630
7 8 10 12 16 20 25 32
S Heavy
N.P. 400
N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
25
MAV - PRESSURE GUAGE CONNECTOR
t3h3
S1
L1
I1 S2
d5
SeriesLL VERY LIGHT
Tube OD4 6
Part No.
Male BSPP Pressure Thread G" " " " " " " " " N.P. 630 N.P. 250 N.P. 100
d5
L1
I1
t3
S1
S2
h3
MAV - 4LLR MAV - 6LR MAV - 8LR MAV - 10LR MAV - 12LR MAV - 6SR MAV - 8SR MAV - 10SR MAV - 12SR
2.5 2.5 5.5 5.5 5.5 3.5 3.5 7 7
33 37 37 38 38 46 46 47 47
8.5 7.5 7.5 8.5 8.5 11 11 10.5 10.5
14.5 14.5 14.5 14.5 14.5 20 20 20 20
19 19 19 19 19 27 27 27 27
10 14 17 19 22 17 19 22 24
4.5 4.5 4.5 4.5 4.5 5 5 5 5
L Light
8 10 12 6
S Heavy
8 10 12
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
26
AS - WELD FITTINGS1 S2
d8
J.J.
I1 L1
Series Tube OD6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
Part No.AS - 6L AS - 8L AS - 10L AS - 12L AS - 15L AS - 18L AS - 22L AS - 28L AS - 35L AS - 42L AS - 6S AS - 8S AS - 10S AS - 12S AS - 14S AS - 16S AS - 20S AS - 25S AS - 30S AS - 38S
Pressure
S112 14 17 19 22 27 32 41 46 55 14 17 19 22 24 27 32 41 46 55
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
L129 31 33 33 37 40 45 47 54 58 34 36 39 41 45 45 51 56 62 69
l114 16 18 18 22 23.5 28.5 30.5 32.5 35 19 21 22.5 24.5 27 26.5 29.5 32 35.5 38
d810 12 14 16 19 22 27 32 40 46 11 13 15 17 19 21 26 31 36 44
N.P. 250
L Light
N.P. 160
N.P. 100
N.P. 630
S Heavy
N.P. 400
N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
27
BUZ - FITTING CAPS2
d1 D1
J.J.
I2Series Tube OD6 8 10 12 L Light 15 18 22 28 35 42 6 8 10 12 S Heavy 14 16 20 25 30 38
Part No.BUZ - 6L BUZ - 8L BUZ - 10L BUZ - 12L BUZ - 15L BUZ - 18L BUZ - 22L BUZ - 28L BUZ - 35L BUZ - 42L BUZ - 6S BUZ - 8S BUZ - 10S BUZ - 12S BUZ - 14S BUZ - 16S BUZ - 20S BUZ - 25S BUZ - 30S BUZ - 38S
Pressure
d1M12 X 1.5 M14 X 1.5
l219.5 19.5 21 21.8 22 24 26 26.5 32 32.5 19.5 19.5 21 21.8 23.5 25.5 30.5 32.5 35.5 40
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
N.P. 250
M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M36 X 2 M45 X 2 M52 X 2 M14 X 1.5 M16 X 1.5
N.P. 160
N.P. 100
N.P. 630
M18 X 1.5 M20 X 1.5 M22 X 1.5 M24 X 1.5
N.P. 400
M30 X 2 M36 X 2 M42 X 2 M52 X 2
N.P. 250
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
28
KOR - TUBE REDUCER LL & L SERIESS1
SeriesLL Very Light
Part No.KOR - 6/4LL KOR - 6/5LL KOR - 8/4LL KOR - 8/5LL KOR - 8/6LL KOR - 8/6L KOR - 10/6L KOR - 10/8L KOR - 12/6L KOR - 12/8L KOR - 12/10L KOR -15/6L KOR -15/8L KOR -15/10L KOR -15/12L KOR - 18/6L KOR - 18/8L KOR - 18/10L KOR - 18/12L KOR - 18/15L KOR - 22/6L KOR - 22/8L KOR - 22/10L KOR - 22/12L KOR - 22/15L KOR - 22/18L KOR - 28/6L KOR - 28/8L KOR - 28/10L KOR - 28/12L KOR - 28/15L KOR - 28/18L KOR - 28/22L KOR - 35/6L KOR - 35/8L KOR - 35/10L KOR - 35/12L KOR - 35/15L KOR - 35/18L KOR - 35/22L KOR - 35/28 KOR - 42/10L KOR - 42/12L KOR - 42/15L KOR - 42/18L KOR - 42/22L KOR - 42/28L KOR - 42/35L
Tube O.D. D1 D2 d16 8 8 10 12 4 5 4 5 6 6 6 8 6 8 10 6 8 10 12 6 8 10 12 15 6 8 10 12 15 18 6 8 10 12 15 18 22 6 8 10 12 15 18 22 28 10 12 15 18 22 28 35 M10 X 1 M12 X 1 M14 X 1.5 M16 X 1.5
L29 29 29 29 29 38
I519 17.5 19 17.5 17.5 23.5 23.5 23.5 23.5 23.5 24.5 23.5 23.5 24.5 24.5 24.5 24.5 25.5 25.5 26.5 25.5 25.5 26.5 26.5 27.5 27 26.5 26.5 27.5 27.5 28.5 28 30 31.5 31.5 32.5 32.5 33.5 33 35 35 33.5 33.5 34.5 34 36 36 35 29
S112 12 14 14 14 17 19 19 22 22 22 27 27 27 27 32 32 32 32 32 36 36 36 36 36 36 41 41 41 41 41 41 41 50 50 50 50 50 50 50 50 60 60 60 60 60 60 60
S210 12 10 12 12 14 14 17 14 17 19 14 17 19 22 14 17 19 22 27 14 17 19 22 27 32 14 17 19 22 27 32 36 14 17 19 22 27 32 36 41 19 22 27 32 36 41 50
PRE INSTALLED S2
d1 D1
J.J.
15
18
22
L Light
28
35
42
38 38 38 M18 X 38 1.5 39 38 38 M22 X 1.5 39 39 39 39 M26 X1.5 40 40 42 40 40 41 M30 X 2 41 43 43 41 41 42 M36 X 2 42 44 44 46 46 46 47 47 M45 X 2 49 49 51 52 48 48 50 M52 X 2 50 52 53 57
I5 L
KOR - TUBE REDUCER S SERIESSeries Part No. Tube O.D. D1 D2 d18 10 12 6 6 8 6 8 10 6 8 10 12 6 8 10 12 14 6 8 10 12 14 16 6 8 10 12 14 16 20 6 8 10 12 14 16 20 25 6 8 10 12 14 16 20 25 30 25 25 M16 X 1.5 M18 X 1.5 M20 X 1.5
L40 41 41 42 42 43 44 44 45 45 44 44 45 45 48 49 49 50 50 53 53 52 52 53 53 55 55 59 54 54 55 55 58 58 61 64 58 58 59 59 62 62 65 68 71 74 80
I525 26 26 27 27 26.5 29 29 28.5 28.5 29 29 28.5 28.5 30 34 34 33.5 33.5 35 34.5 37 37 36.5 36.5 37 36.5 37.5 39 39 38.5 38.5 40 39.5 39.5 40 43 43 42.5 42.5 44 43.5 43.5 44 44.5 50 56
S119 22 22 24 24 24 27 27 27 27 30 30 30 30 30 36 36 36 36 36 36 46 46 46 46 46 46 46 50 50 50 50 50 50 50 50 60 60 60 60 60 60 60 60 60 55 70
S217 17 19 17 19 22 17 19 22 24 17 19 22 24 27 17 19 22 24 27 30 17 19 22 24 27 30 36 17 19 22 24 27 30 36 46 17 19 22 24 27 30 36 46 50 46 46
S1 PRE INSTALLED S2
KOR - 8/6S KOR - 10/6S KOR - 10/8S KOR - 12/6S KOR - 12/8S KOR - 12/10S KOR -14/6S KOR -14/8S KOR -14/10S KOR -14/12S KOR - 16/6S KOR - 16/8S KOR - 16/10S KOR - 16/12S KOR - 16/14S KOR - 20/6S KOR - 20/8S KOR - 20/10S KOR - 20/12S KOR - 20/14S KOR - 20/16S KOR - 25/6S KOR - 25/8S KOR - 25/10S S HEAVY KOR - 25/12S KOR - 25/14S KOR - 25/16S KOR - 25/20S KOR - 30/6S KOR - 30/8S KOR - 30/10S KOR - 30/12S KOR - 30/14S KOR - 30/16S KOR - 30/20S KOR - 30/25S KOR - 38/6S KOR - 38/8S KOR - 38/10S KOR - 38/12S KOR - 38/14S KOR - 38/16S KOR - 38/20S KOR - 38/25S KOR - 38/30S KOR 30400/25 KOR 38400/25
d1 D1
J.J.
14
M22 X 1.5
I5 L
16
M24 X 1.5
20
M30 X 2
25
M36 X 2
30
M42 X 2
38
M52 X 2
30 38
M45 X 2 M56 X 2
30
SKA - WELD NIPPLE
D
d
J.J.
L
Series
Part No.
O-Rings For Precision Shore HardPressure steel tube DIN ness 'A' 2391 approx 9010 X 2 12 X 2.5 N.P. 400 14 X 3 16 X 3 20 X 4 25 X 5 N.P. 315 N.P. 250 N.P. 315 N.P. 250 25 X 4 30 X 5 30 X 4 38 X 6 38 X 5 7.5 X 1.5 9 X 1.5 10 X 2 12 X 2 16.3 X 2.4 20.3 X 2.4 20.3 X 2.4 25.3 X 2.4 25.3 X 2.4 33.3 X 2.4 33.3 X 2.4
D
d
L
SKA 10 SKA 12 SKA 14 SKA 16 SKA 20 S SKA 25 X 5 HEAVY SKA 25 SKA 30 X 5 SKA 30 SKA 38 X 6 SKA 38
10 12 14 16 20 25 25 30 30 38 38
6 7 8 10 12 15 17 20 22 26 28
36 36 41.5 44 50.5 56 56 64.5 64.5 74 74
NB : FOR INCH O.D. AND NOMINAL BORE O.D. FITTINGS KINDLY CONTACT US.
31
RI BSPP REDUCING ADOPTERS1
L
I
d1
J.J.d3 G
t3
Part No.RI " X " RI " X " RI " X " RI " X " RI " X " RI " X " RI " X " RI " X " RI " X " RI " X " RI " X " RI " X 1 " RI " X 1" RI " X " RI " X 1" RI " X 1 " RI " X 1 " RI 1" X " RI 1" X 1 " RI 1" X 1 " RI 1 " X 1" RI 1 " X 1 RI 1 X 1 "
BSPP Thread Male G" " " " " " " " " " " " " " " " " 1" 1" 1" 1 " 1 " 1
Female d1" " " " " " " " " " " 1 " 1" " 1" 1 " 1 " 1 " 1 1" 1 1 " 32
I31 32 28 36 40 43 36 41 44 36 46 49 53 41 51 55 57 47 57 59 52 60 58
i8 8 12 12 12 12 12 12 12 14 14 14 14 16 16 16 16 18 18 18 20 20 22
S119 24 19 24 30 36 22 30 36 27 36 41 55 31 42 55 60 41 55 60 50 60 55
d4 4 5 5 5 5 8 8 8 12 12 12 10 16 16 16 16 20 20 20 25 25 32
d314 14 18 18 18 18 22 22 22 26 26 26 26 32 32 32 32 39 39 39 49 49 55
t217 17 12 17 20 22 17 20 22 17 22 24.5 26.5 20 24.5 26.5 28.5 22 26.5 28.5 24.5 28.5 26.5
VSH - REINFORCING RING FOR THIN WALL TUBINGL J.J. d d1
Tube O.D. & Wall Thickness 6X1 6 X 0.5 8X1 10 X 1.5 10 X 1 12 X 1.5 12 X 1 15 X 1.5 15 X 1 18 X 1.5 18 X 1 20 X 1 22 X 1.5 22 X 1 25 X 1.5 28 X 2 28 X 1.5 35 X 2 42 X 2
Part No
Tube ID 4 5 6 7 8 9 10 12 13 15 16 18 19 20 22 24 25 31 38
L 15.5 15.5 15.5 17 16.5 16.5 16.5 17.5 18.5 17.5 22 22 18 18 23.5 18 18 22.5 23.5
d 2.6 3.6 4.6 5.6 6.6 7.6 8.6 10.2 11.6 13.2 14.2 16.2 17.2 18.2 20.2 22.2 23.2 28.8 35.8
d1 3.8 4.8 5.8 6.8 7.8 8.8 9.8 11.8 12.8 14.8 15.8 17.8 18.8 19.8 21.8 23.8 24.8 30.8 37.8
VSH 6 X 1 VSH 6 X 0.5 VSH 8 X 1 VSH 10 X 1.5 VSH 10 X 1 VSH 12 X 1.5 VSH 12 X 1 VSH 15 X 1.5 VSH 15 X 1 VSH 18 X 1.5 VSH 18 X 1 VSH 20 X 1 VSH 22 X 1.5 VSH 22 X 1 VSH 25 X 1.5 VSH 28 X 2 VSH 28 X 1.5 VSH 35 X 2 VSH 42 X 2
33
PIPE CLAMP
1
PIPE CLAMP INTRODUCTION
2
TECHNICAL DETAILSPipe O.D. 6mm to 12.7mm 12.7mm to 22mm 22mm to 32mm 32mm to 38mm 38mm to 57mm 57mm to 75mm 75mm to 88.9mm 88.9mm to 102mm 102mm to 114mm 114mm to 168mm 168mm to 219mm Recommended Spacing 1meter 1.2 meter 1.5 meter 2meter 2.7meter 3 meter 3.5 meter 4 meter 4.5 meter 5 meter 6 meter
3
PIPE CLAMP - STANSDARD SERIES
ALL DIMENSIONS ARE IN MMDIN Group PIPE OD D dia 6 6.4 8 9.5 10 12 6 6.4 8 9.5 10 12 12.7 13.5 14 15 16 17.2 18 19 20 21.3 22 25 26.9 28 30 32 33.7 35 38 40 42 44.5 48.3 a2 a3 a1 T h2
0
30
28
-
3
33
1
34
40
20
3
39
2
48
42
26
3
39
3
56
50
33
3
42
4
65
59
40
3
48
5
77
71
52
3
64
6
92
86
66 4
3
72
PIPE CLAMP - HEAVY SERIES
ALL DIMENSIONS ARE IN MMDIN Group PIPE OD D dia 6 6.4 8 9.5 10 12 1 12.7 13.5 14 15 16 17.2 18 19 20 21.3 22 2 25 26.9 28 30 30 33.7 3 35 38 42 42 48.3 50.8 4 60.3 63.5 65 70 73 5 76.1 88.9 102 114 6 127 133 141 152 7 168 a3 a1 h2 b1 a2 s
55
33
48
30
70
8
70
45
64
30
86
8
85
60
76
30
100
8
115
90
120
45
140
10
152
122
140
60
180
10
206
168
197
80
226
15
251
205
230
91
270
15
SIZES UPTO 8" NB AVAILABLE 5
PIPE CLAMP - STANDARD SERIES WITH RUBBER INSERT
ALL DIMENSIONS ARE IN MMDIN Group PIPE OD D dia 10 12 12.7 13.5 14 4 15 16 17.2 18 19 2021.3 22 25
a2
a3
a1
S
h3
65
59
40
3
48
626.9 28 30 32
92
86
66
3
72
6
PIPE CLAMP - HEAVY SERIES WITH RUBBER INSERT
ALL DIMENSIONS ARE IN MMDIN Group PIPE OD D dia 10 12 12.7 13.5 14 15 16 17.2 18 19 20 21.3 22 25 26.9 28 30 32 35 38 40 42 48.3 50.8 56.4 60 65 72 76 80 a3 a1 h3 W a2 s
2
70
45
64
30
86
8
3
85
60
76
30
100
8
4
115
90
120
45
140
10
5
152
122
140
60
180
10
6
206 7
168
197
80
226
15
PIPE CLAMP - TWIN SERIES
ALL DIMENSIONS ARE IN MMDIN Group PIPE OD D dia 6 6.4 8 9.5 10 12 12.7 13.5 14 15 16 17.2 18 19 20 21.3 22 25 26.9 28 30 32 33.7 35 38 40 42 a2 a3 a1 T h2 h3 h1
1
42
36
20
5
27
43
18.5
2
59
53
29
5
27
43
18.5
3
74
67
36
5
37
51
23.5
4
86
80
45
5
40
55
25
5
112
106
56
5
53
68
31.5
8
Flange
1
SOCKET WELD IN-LINE PIPE FLANGE
3000 SeriesPipe Size" " 1" 1 " 1 " 2" 2 " 3" 3 " 4" 5"
Part No.8-SWFL-61 12-SWFL-61 16-SWFL-61 20-SWFL-61 24-SWFL-61 32-SWFL-61 40-SWFL-61 48-SWFL-61 56-SWFL-61 64-SWFL-61 72-SWFL-61
A38.1 44.5 50.8 63.5 69.9 82.6 101.6 114.3 127.0 139.7 177.8
B53.8 66.5 71.6 81.0 95.3 101.6 114.3 134.9 152.4 162.1 184.2
C19.1 25.4 25.4 25.4 31.8 38.1 44.5 50.8 38.1 38.1 50.8
D38.1 47.6 52.4 58.7 69.9 77.8 88.9 106.4 120.7 130.2 152.4
E17.5 22.2 26.2 30.2 35.7 42.9 50.8 61.9 69.9 77.8 92.1
H9.7 12.7 12.7 12.7 12.7 15.7 19.1 19.1 19.1 19.1 19.1
K21.8 27.2 33.9 42.7 48.8 61.2 73.9 89.9 102.7 115.6 143.1
Note :1) 2 " is for maximum 2500 PSI 2) 3" is for maximum 2000 PSI 3) 3", 4" & 5" are for maximun 500 PSI
6000 SeriesPipe Size" " 1" 1 " 1 " 2" 2 " 3"
Part No.8-SWFL-62 12-SWFL-62 16-SWFL-62 20-SWFL-62 24-SWFL-62 32-SWFL-62 40-SWFL-62 48-SWFL-62
A44.5 50.8 57.2 69.9 82.6 101.6 127.0 152.4
B56.4 71.4 81.0 95.3 114.3 133.4 174.8 215.9
C25.4 25.4 25.4 31.8 38.1 44.5 50.8 63.5
D40.5 50.8 57.2 66.7 79.4 96.8 123.8 152.4
E18.2 23.8 27.8 31.8 36.5 44.5 58.7 71.4
H12.7 12.7 12.7 12.7 12.7 15.7 15.7 15.7
K21.8 27.2 33.9 42.7 48.8 61.2 73.9 89.9
Note :1) 2 " & 3" not included in SAE J518 2
BUTT WELD IN-LINE PIPE FLANGE
3000 SeriesPipe Size Part No. A B53.8 66.5 71.6 81.0 95.3 101.6 114.3 134.9 152.4 162.1 184.2
C31.8 31.8 31.8 31.8 38.1 38.1 44.5 50.8 38.1 38.1 50.8
D38.1 47.6 52.4 58.7 69.9 77.8 88.9 106.4 120.7 130.2 152.4
E17.5 22.2 26.2 30.2 35.7 42.9 50.8 61.9 69.9 77.8 92.1
F13.5 19.1 23.9 31.8 38.1 49.3 58.9 73.7 85.3 97.3 122.2
8-BWPFL-61 38.1 " 12-BWPFL-61 44.5 " 16-BWPFL-61 50.8 1" 20-BWPFL-61 63.5 1 " 24-BWPFL-61 69.9 1 " 32-BWPFL-61 82.6 2" 40-BWPFL-61 101.6 2 " 48-BWPFL-61 114.3 3" 56-BWPFL-61 127.0 3 " 64-BWPFL-61 139.7 4" 72-BWPFL-61 177.8 5" Note :1) 2 " is for maximum 2500 PSI 2) 3" is for maximum 2000 PSI 3) 3", 4" & 5" are for maximun 500 PSI
6000 SeriesPipe Size Part No. A B56.4 71.4 81.0 95.3 114.3 133.4 174.8 215.9
C31.8 31.8 31.8 31.8 38.1 44.5 50.8 63.5
D40.5 50.8 57.2 66.7 79.4 96.8 123.8 152.4
E18.2 23.8 27.8 31.8 36.5 44.5 58.7 71.4
F13.5 19.1 23.9 31.8 38.1 49.3 58.9 73.7
8-BWPFL-62 44.5 " 12-BWPFL-62 50.8 " 16-BWPFL-62 57.2 1" 20-BWPFL-62 69.9 1 " 24-BWPFL-62 82.6 1 " 32-BWPFL-62 101.6 2" 40-BWPFL-62 127.0 2 " 48-BWPFL-62 152.4 3" Note :1) 2 " & 3" not included in SAE J518
3
METRIC SPLIT FLANGES
3000 SeriesPipe Size Part No. A46.0 52.1 58.7 73.2 73.2 82.6 82.6 96.8 96.8 108.7 108.7 131.1
B53.8 65.0 69.9 79.2 79.2 93.7 93.7 101.6 101.6 114.3 114.3 134.9
C12.7 14.2 15.7 14.2 14.2 15.7 15.7 15.7 15.7 19.1 19.1 22.4
D38.1 47.6 52.4 58.7 58.7 69.9 69.9 77.8 77.8 88.9 88.9 106.4
E17.5 22.2 26.2 30.2 30.2 35.7 35.7 42.9 42.9 50.8 50.8 61.9
K31.0 38.9 45.2 51.6 51.6 61.1 61.1 72.2 72.2 84.9 84.9 102.4
Bolt SizeM8 X 25 M10 X 30 M10 X 30 M10 X 30 M12 X 35 M12 X 35 M14 X 40 M12 X 35 M14 X 40 M12 X 40 M14 X 45 M16 X 50
8-MSFL-61 " 12-MSFL-61 " 16-MSFL-61 1" 20-MSFL-61 1 " 20-MSFL-61 1 " 24-MSFL-61 1 " 24-MSFL-61 1 " 32-MSFL-61 2" 32-MSFL-61 2" 40-MSFL-61 2 " 40-MSFL-61 2 " 48-MSFL-61 3" Note :1) 2 " is for maximum 2500 PSI 2) 3" is for maximum 2000 PSI
6000 SeriesPipe Size" " 1" 1 " 1 " 1 " 2"
Part No.8-MSFL-62 12-MSFL-62 16-MSFL-62 20-MSFL-62 24-MSFL-62 32-MSFL-62 40-MSFL-62
A47.8 60.5 69.9 77.7 77.7 95.3 114.3
B56.4 71.4 81.0 95.3 95.3 112.776 133.4
C15.7 19.1 23.9 26.9 26.9 30.2 36.6
D40.5 50.8 57.2 66.7 66.7 79.4 96.8
E18.2 23.8 27.8 31.8 31.8 36.5 44.5
K32.5 42.1 48.4 54.8 54.8 64.3 80.2
Bolt SizeM8 X 30 M10 X 35 M12 X 45 M12 X 45 M14 X 50 M16 X 55 M20 X 70
4
SQUARE SOCKET WELD IN LINE PIPE FLANGE
3000 SeriesPipe Size" " 1" 1 " 1 " 2" 2 " 3" 3 " 4" 5" 6"
Part No.8-SQSWFL-61 12-SQSWFL-61 16-SQSWFL-61 20-SQSWFL-61 24-SQSWFL-61 32-SQSWFL-61 40-SQSWFL-61 48-SQSWFL-61 56-SQSWFL-61 64-SQSWFL-61 72-SQSWFL-61 80-SQSWFL-61
A57.2 57.2 76.2 76.2 101.6 101.6 139.7 139.7 152.4 177.8 203.2 254.0
C25.4 25.4 25.4 25.4 31.8 31.8 38.1 38.1 44.5 50.8 63.5 63.5
E36.5 36.5 50.8 50.8 69.9 69.9 95.3 95.3 108.0 127.0 152.4 177.8
F12.7 19.1 25.4 31.8 38.1 49.3 62.0 73.2 85.9 98.6 122.2 146.1
H12.7 12.7 12.7 12.7 15.7 15.7 19.1 19.1 19.1 19.1 25.4 25.4
K21.8 27.2 33.9 42.7 48.8 61.2 73.9 89.9 102.7 115.6 143.1 170.1
L34.9 34.9 44.5 44.5 63.5 63.5 88.9 88.9 101.6 117.5 142.9 168.3
6000 SeriesPipe Size1" 1 " 1 " 2" 2 " 3" 3 " 4" 5"
Part No.16-SQSWFL-62 20-SQSWFL-62 24-SQSWFL-62 32-SQSWFL-62 40-SQSWFL-62 48-SQSWFL-62 56-SQSWFL-62 64-SQSWFL-62 72-SQSWFL-62
A76.2 101.6 101.6 127.0 139.7 177.8 203.2 215.9 254.0
C25.4 31.8 38.1 44.5 44.5 50.8 63.5 63.5 76.2
E50.8 69.9 69.9 88.9 95.3 120.7 139.7 152.4 184.2
F20.6 29.5 34.0 42.9 53.8 66.5 76.2 87.4 109.5
H12.7 12.7 15.7 15.7 19.1 19.1 25.4 25.4 28.4
K33.9 42.7 48.8 61.2 73.9 89.9 102.7 115.6 143.1
L39.7 44.5 54.0 63.5 76.2 88.9 101.6 114.3 136.5
5
BLANKING
3000 SeriesPipe Size" " 1" 1 " 1 " 2" 2 " 3" 3 " 4"
Part No.8-BLFL-61 12-BLFL-61 16-BLFL-61 20-BLFL-61 24-BLFL-61 32-BLFL-61 40-BLFL-61 48-BLFL-61 56-BLFL-61 64-BLFL-61
A46.1 52.4 58.8 73.0 82.6 96.9 108.7 131.0 139.7 152.4
B54.0 65.1 69.9 79.4 93.7 101.6 114.3 135.0 152.4 162.1
C17.5 22.2 26.2 30.2 35.7 42.9 50.8 61.9 69.9 77.8
D38.1 47.6 52.4 58.8 69.9 77.8 88.9 106.4 120.7 130.2
E19.1 19.1 22.4 23.9 30.2 36.6 46.2 55.6 36.6 36.6
F25.4 31.8 39.6 44.5 53.7 63.2 76.1 91.8 104.0 116.7
G8.7 10.3 10.3 11.9 13.5 13.5 13.5 16.7 16.7 16.7
6000 SeriesPipe Size" " 1" 1 " 1 " 2" 2 " 3"
Part No.8-BLFL-62 12-BLFL-62 16-BLFL-62 20-BLFL-62 24-BLFL-62 32-BLFL-62 40-BLFL-62 48-BLFL-62
A49.3 63.5 69.9 77.7 95.3 114.3 149.1 177.8
B58.4 74.9 81.0 95.3 112.8 133.4 174.5 215.9
C18.2 23.8 27.8 31.8 36.5 44.5 58.7 71.4
D40.5 50.8 57.2 66.7 79.4 96.8 123.8 152.4
E31.8 31.8 38.1 36.3 46.2 46.2 49.0 68.3
F25.4 31.8 39.6 44.5 53.7 63.2 76.1 91.8
G8.7 10.3 12.5 13.5 16.7 19.8 23.0 30.2
6
BSPP THREAD
3000 SeriesPipe Size" " 1" 1 " 1 " 2"
Part No.8-GFL-61 12-GFL-61 16-GFL-61 20-GFL-61 24-GFL-61 32-GFL-61
A46.0 50.0 55.1 68.1 78.0 89.9
B54.1 65.0 69.9 79.2 93.0 101.6
C17.5 22.2 26.2 30.2 35.7 42.9
D38.1 47.6 52.4 58.7 69.9 77.8
E36.1 36.1 38.1 40.9 45.0 45.0
F16.0 18.0 18.0 21.1 24.9 24.9
G25.4 31.8 39.6 38.1 53.7 63.2
H12.8 19.1 25.5 31.8 38.2 50.9
J BSPP" - 14 " - 14 1" - 11 1 " - 11 1 " - 11 2" - 11
6000 SeriesPipe Size" " 1" 1 " 1 " 2"
Part No.8-GFL-62 12-GFL-62 16-GFL-62 20-GFL-62 24-GFL-62 32-GFL-62
A46.0 55.1 65.0 78.0 94.0
B56.1 71.1 81.0 95.3 112.0
C18.2 23.8 2.6 31.8 36.5 44.5
D40.5 50.8 57.2 66.7 79.4 96.8
E36.1 35.1 41.9 45.0 50.0 65.0
F16.0 21.1 24.9 26.9 30.0 37.1
G25.4 31.8 39.6 44.5 53.7 63.2
H12.8 19.1 25.5 31.8 38.2 50.9
J BSPP" - 14 " - 14 1" - 11 1 " - 11 1 " - 11 2" - 11
114.3 134.1
NB :- FIG 1 IS WITH O RING WHILE FIG 2 IS FLAT FACE
7
FLAT SOCKET WELD PIPE
3000 SeriesPipe Size" " 1" 1 " 1 " 2" 2 " 3"
Part No.8-SWOFL-61 12-SWOFL-61 16-SWOFL-61 20-SWOFL-61 24-SWOFL-61 32-SWOFL-61 40-SWOFL-61 48-SWOFL-61
A46.1 52.4 58.8 73.0 82.6 96.9 108.7 131.0
B54.0 65.1 69.9 79.4 93.7 101.6 114.3 135.0
C17.5 22.2 26.2 30.2 35.7 42.9 50.8 61.9
D38.1 47.6 52.4 58.8 69.9 77.8 88.9 106.4
E19.1 19.1 22.4 23.9 30.2 35.1 44.5 53.8
F14.2 14.2 16.0 17.5 19.1 22.2 25.4 31.8
G25.4 31.8 39.6 44.5 53.7 63.2 76.1 91.8
H12.8 19.1 25.5 31.8 38.2 50.9 63.6 76.3
J21.7 27.0 33.7 42.5 48.8 61.1 73.8 90.1
6000 SeriesPipe Size" " 1" 1 " 1 " 2" 2 " 3"
Part No.8-SWOFL-62 12-SWOFL-62 16-SWOFL-62 20-SWOFL-62 24-SWOFL-62 32-SWOFL-62 40-SWOFL-62 48-SWOFL-62
A49.3 63.5 69.9 77.7 95.3 114.3 149.1 177.8
B58.4 74.9 81.0 95.3 112.8 133.4 174.5 215.9
C18.2 23.8 27.8 31.8 36.5 44.5 58.7 71.4
D40.5 50.8 57.2 66.7 79.4 96.8 123.8 152.4
E31.8 31.8 38.1 38.1 44.5 44.5 52.3 66.5
F14.2 14.2 16.0 17.5 19.1 22.2 25.4 31.8
G25.4 31.8 39.6 44.5 53.7 63.2 76.1 91.8
H12.8 19.1 25.5 31.8 38.2 50.9 63.6 76.3
J21.7 27.0 33.7 42.5 48.8 61.1 73.8 90.1
3000 SeriesPipe Size*3" 3 " 4" 5"
Part No.*48-SWOFL-61 56-SWOFL-61 64-SWOFL-61 72-SWOFL-61
A130.0 139.7 152.4 180.8
B134.9 152.4 162.1 184.2
C61.9 69.9 77.8 92.1
D106.4 120.7 130.2 152.4
E35.1 36.6 38.1 44.5
F28.4 30.2 31.8 35.1
G91.8 104.0 116.7 142.1
H76.3 89.0 101.7 127.1
J90.1 102.8 116.3 143.3
NB :- * INDICATES MAX 500 PSI FOR 3"
8
BUTT WELD PIPE
3000 SeriesPipe Size" " 1" 1 " 1 " 2" 2 " 3"
Part No.8-BWOFL-61 12-BWOFL-61 16-BWOFL-61 20-BWOFL-61 24-BWOFL-61 32-BWOFL-61 40-BWOFL-61 48-BWOFL-61
A46.0 50.0 55.1 68.1 78.0 89.9 103.9 124.0
B54.1 65.0 69.9 79.2 93.0 101.6 114.0 134.1
C17.5 22.2 26.2 30.2 35.7 42.9 50.8 61.9
D38.1 47.6 52.4 58.7 69.9 77.8 88.9 106.4
E36.1 36.1 38.1 40.9 43.9 45.0 50.0 50.0
F16.0 18.0 18.0 21.1 24.9 24.9 24.9 26.9
G25.4 31.8 39.6 44.5 53.7 63.2 76.1 91.8
H13.9 18.9 24.4 32.5 38.2 49.3 59.1 73.7
J21.3 26.7 33.4 42.2 48.3 60.3 73.0 88.9
6000 SeriesPipe Size" " 1" 1 " 1 " 2"
Part No.8-BWOFL-62 12-BWOFL-62 16-BWOFL-62 20-BWOFL-62 24-BWOFL-62 32-BWOFL-62
A46.0 55.1 65.0 78.0 94.0 114.3
B56.1 71.1 81.0 95.3 112.0 134.1
C18.2 23.8 27.8 31.8 36.5 44.5
D40.5 50.8 57.2 66.7 79.4 96.8
E36.1 35.1 40.9 43.9 55.1 65.0
F16.0 21.1 21.1 24.9 30.0 37.1
G25.4 31.8 39.6 44.5 53.7 63.2
H13.9 18.9 24.4 32.5 38.2 49.3
J21.3 26.7 33.4 42.2 48.3 60.3
NB :- FIG 1 IS WITH O RING WHILE FIG 2 IS FLAT FACE
9
CALIBRATED NEEDLE AND SHUT OFF VALVES SERIES - CNSV
Orifice & Flow Chart
Free BSP/NPT Flow Part No. A Dia2 CNSV 0.12 2 CNSV 0.30" 6 CNSV 0.39" 8 CNSV 0.48" 12 CNSV 0.65" 16 CNSV 1" 0.86" 24 CNSV 1 0.62" 1 & 1 ON REQUEST
Part No.2 CNSV 4 CNSV 6 CNSV 8 CNSV 12 CNSV 16 CNSV
BSP/NPT B C A Open Shut 1" 14 17 19 22 27 32 35 40 49 61 71 107
D27 29 30 32 36 40
E12 14 15 17 21 23.5
F26 27.5 29 30.5 33.5 36
G6 8 10 12 15 18
1 & 1 ON REQUEST
Pressure Rating Brass Valve C.S. Valve S.S. Valve 2000 PSI 5000 PSI 5000 PSI
Sr. No1 2 3 4 5 6 7
DescriptionBody Needle Ball Lock Allen Key Seal Colour Ring Knob
Qty1 1 1 1 5 1
Material C.S. Brass
S.S.
C.S. Brass C.S. S.S.304 S.S.304 S.S.304 C.S. C.S. C.S. Brass Brass Brass Teflon/Buna "N" AL AL AL C.S. C.S. C.S.
NB :- SPECIFY 'R' FOR BSP AND 'N' FOR NPT THREAD
1
CHECK VALVE (SCREWED END) SERIES - CVR/N
Part No.2 CVR 2 CVN 4 CVR 4 CVN 6 CVR 6 CVN 8 CVR 8 CVN 12 CVR 12 CVN 16 CVR 16 CVN 20 CVR 20 CVN 24 CVR 24 CVN 32 CVR 32 CVN
A&B Connection" " " " " " " " " " 1" 1" 1 " 1 " 1 " 1 " 2" 2"
C&D Hex22 22 22 22 27 27 32 32 41 41 50 50 65 65 65 65 70 70
E65 64 72 75 83 90 98 105 125 130 145 150 160 167 160 167 185 197
Material Sr. No Description C.S. Brass S.S.1 2 3 4 5 6 Body Poppet Spring O Ring Retainer End Coupling C.S. C.S. S.S Brass S.S. Steel S.S S.S S.S Viton Nylon S.S.
Buna 'N' Buna 'N Nylon C.S. Nylon Brass
NB : 1) Cracking Pressure Standard 0.5 to 1.5 Kg/cm 2) On request upto 5 Kg/cm 3) Maximum operating pressure for Brass is 3000 psi 4) Maximum operating pressure for C.S. & S.S. is 6000 psi/10000 psi
2
NON COMPENSATED FLOW CONTROL VALVE SERIES - FCV
Orifice & Flow Chart
Free Max BSP/NPT Flow Flow/ Part No. A Dia GPM4 FCV 0.30" 6 FCV 0.39" 8 FCV 0.48" 12 FCV 0.65" 16 FCV 0.86" 1 " & 2" ON REQUEST 6 8 12 27 40
Part No.4 FCV 6 FCV 8 FCV 12 FCV 16 FCV
BSP/ B C NPT A Open Shut" " " " 1" 45 55 68 86 124 40 50 61 71 107
D27 29 30 32 36
SQ E20 25 32 38 44
G66 69 87 98 127
J11 12 16 16 20
1 " & 2" ON REQUEST
Pressure Rating Brass Valve C.S. Valve S.S. Valve 2000 PSI 5000 PSI 5000 PSI
Sr. No1 2 3 4 5 6 7 8 9 10 11
DescriptionBody Spring Poppet Needle Retainer Allen Key O Ring Seal Black Up Ring Colour Ring Lock Screw Knob
Material C.S. BrassC.S. C.S. C.S. S.S. 304 C.S. STD Buna 'N' Teflon ALU Brass C.S. Brass Brass C.S. S.S. 304 Brass STD Buna 'N' Teflon ALU Brass C.S.
NB :- SPECIFY 'R' FOR BSP AND 'N' FOR NPT THREAD
3
SHUT OFF VALVE (SCREWED ENDS) SERIES - LKV
Part No. Part No. Size BSP NPT T THREAD THREAD2 LKVR 4 LKVR 6 LKVR 8 LKVR 12 LKVR 16 LKVR 20 LKVR 24 LKVR 32 LKVR 2 LKVN 4 LKVN 6 LKVN 8 LKVN 12 LKVN 16 LKVN 20 LKVN 24 LKVN 32 LKVN " " " " " 1" 1 " 1 " 2"
A50 50 64 80 88 110 150 160 225
Shut Open HT HT88 85 78 85 98 121 146 165 188 98 94 88 94 104 129 161 177 220
Pressure Rating Size " to 1" 400 Kg/cm
Size 1 " to 1 " 200 Kg/cm Size 2" 150 Kg/cm
DescripSr. No tion1 2 3 4 5 6 7 8 9 Body Washer Gland Body Spindle Check Nut
C.S.C.S. C.U. C.S. S.S.
Material S.S. S.S. 316 304S.S. 304 S.S. 316 C.U. S.S. C.S. Teflon S.S. S.S. STD C.S. Teflon S.S. S.S. C.U. S.S. S.S. 304 S.S. 316
Gland Seal Buna 'N' Retainer Gland Nut Handle C.S. C.S.
NB : 1) C.S. Valve Galvanised & Dichromated 2) Panel Mounting is available upto 1", please specify it for above 1"
4
BAR STOCK MINIATURE NEEDLE VALVE SCREWED MMVR/W
Part No.2 MMVR 2 MMVN 4 MMVR 4 MMVN 6 MMVR 6 MMVN 8 MMVR 8 MMVN
Connection P" BSP " NPT " BSP " NPT " BSP " NPT " BSP " NPT
L50 50 50 50 56 56
Shut HT52 52 52 52 55 55 ON REQUEST
Open HT58 58 58 58 62 62
Sr. No1 2 3 4 5 6
DescriptionBody Stem Seal Retainer Nut Handle Handle Screw
Material C.S.C.S. S.S. Teflon C.S. C.S. STD
BrassBrass S.S. Teflon Brass C.S. STD
S.S.S.S. S.S. Teflon S.S. S.S. STD
NB : 1) Maximum Operating pressure for C.S. & S.S. is 200 Kc/cm and that of Brass is 100 Kg/cm 2) For Pneumatic service pressure rating will be half of the above. 3) Kindly mention the material of body.
5
NEEDLE VALVE (SCREWED ENDS) SERIES - MVR/N
Part No.2 MVR 2 MVN 4 MVR 4 MVN 6 MVR 6 MVN 8 MVR 8 MVN 12 MVR 12 MVN 16 MVR 16 MVN 20 MVR 20 MVN 24 MVR 24 MVN
A & B Connection" BSP " NPT " BSP " NPT " BSP " NPT " BSP " NPT " BSP " NPT 1" BSP 1" NPT 1 " BSP 1 " NPT 1 " BSP 1 " NPT
E45 45 50 56 65 65 72 72 80 80 85 85 135 135 150 150
Shut HT Open HT82 82 82 82 82 82 82 82 90 90 110 110 145 145 160 160 88 88 88 88 88 88 88 88 98 98 118 118 153 153 170 170
Sr. No1 2 3 4 5 6 7 8 9
DescriptionBody Washer Gland Body Spindle Check Nut Gland Seal Gland Retainer Gland Nut Handle
Qty1 1 1 1 1 3 1 1 1
Material C.S. Brass S.S.C.S. C.U. C.S. S.S. C.S. Buna 'N' C.S. C.S. Brass S.S. C.U. C.U. Brass S.S. S.S. S.S. C.S. C.S. Teflon Teflon Brass S.S. Brass S.S. STD C.S.
NB : 1) Panel Mounting is available upto 1" 2) Available in socket weld connection also.
6
NEEDLE VALVE (TUBE ENDS) SERIES - MV
For Metric Size TubingSeries Part No.MV 6L MV 8L MV 10L MV 12L MV 15L MV 18L MV 22L MV 28L MV 6S MV 8S MV 10S MV 12S MV 14S MV 16S MV 20S MV 25S
For Inch Size NB TubingOpen Shut Tube HT HT Part No. OD92 92 92 100 100 115 115 125 92 92 92 100 100 115 115 125 86 86 86 90 90 100 100 110 86 86 86 90 90 100 100 110 2 MVNB 4 MVNB 6 MVNB 8 MVNB 12 MVNB " " " " "
Tube PresOD sure6 8 10 12 15 18 22 28 6 8 10 12 14 16 20 25 N.P. 250 N.P. 160 N.P. 100 N.P. 640
A38 38 38 40 42 45 42 53 38 38 38 41 42 43 47 54
B68 68 68 70 72 78 82 83 68 68 68 74 78 80 90 101
A38 42 43 47 54
B68 78 81 93 101
Open Shut HT HT92 100 115 115 125 86 90 100 100 110
L Light
For Inch Size NB TubingPart No. Tube OD A38 38 38 38 40 43 44 54
B60 70 68 71.5 75 80 86 101
Open Shut HT HT92 92 92 92 100 115 115 125 86 86 86 86 90 100 100 110
S Heavy
N.P. 400
Sr. No1 2 3 4 5 6 7 8 9 10 11 12
DescriptionBody Washer Spindle Gland Body Check Nut Gland Seal Gland Retainer Gland Nut Handle Nut Ferrule Tube
C.S.C.S. C.U. S.S. C.S. C.S.
Material S.S. S.S.
2 MVNB " 4 MVNB " 5 MV 5/16" 6 MVNB " 8 MVNB " 10 MV " 12 MVNB " 16 MV 1"
S.S. 304 S.S. 316 C.U. C.U S.S. 304 S.S. 316 S.S. 304 S.S. 316 C.S. C.S. Buna 'N' / Teflon C.S. S.S. 304 S.S. 316 C.D S.S. 304 S.S. 316 C.S. C.S. S.S. 304 S.S. 304 S.S. 316 S.S. 316
7
NON RETURN VALVE (TUBE END) SERIES - RHD
Series
Part No.RHD 6L RHD 8L RHD 10L RHD 12L RHD 15L RHD 18L RHD 22L RHD 28L RHD 35L RHD 42L RHD 6S RHD 8S RHD 10S RHD 12S RHD 14S RHD 16S RHD 20S RHD 25S RHD 30S RHD 38S
Tube OD6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38
PressureN.P. 250
S117 19 22 27 27 36 41 50 60 65 19 19 22 24 27 32 41 46 60 65
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
S317 19 24 30 32 36 46 55 60 70 19 19 24 27 32 36 46 50 60 70
L1
L2
L Light
N.P. 160 N.P. 100
S Heavy
N.P. 400
N.P. 250
58 29 59 30 69.5 40.5 72.5 43.5 77.5 47.5 83.5 51.5 93.5 61.5 102.5 69.5 117.5 74.5 119 74 63.5 34.5 63.6 34.5 72.5 40.5 74.5 42.5 82.5 47.6 86.5 50.5 97.5 54.5 106.5 58.5 112.5 69.5 136.5 75.5
Sr. No Description1 2 3 4 5 6 7 8 9
Material C.S. Brass S.S.
Body (Male) C.S. Brass S.S. Body (Female) C.S. Brass S.S. Poppet C.S. Brass S.S. Seal Buna 'N' Buna 'N' Buna 'N' Retainer C.S. Brass S.S. Spring C.S. C.S. S.S. Retainer C.S. Brass S.S. Nut C.S. Brass S.S. Ferrule C.S. Brass S.S.
NB : 1) Cracking Pressure Standard 0.5 to 1.5 Kg/cm 2) On request upto 6 Kg/cm 3) Kindly mention material of the body
8
NON RETURN VALVE (TUBE END) SERIES - RHV
Series
Part No.RHV 6LR-ed RHV 8LR-ed RHV 10LR-ed RHV 12LR-ed RHV 15LR-ed RHV 18LR-ed RHV 22LR-ed RHV 28LR-ed RHV 35LR-ed RHV 42LR-ed RHV 6SR-ed RHV 8SR-ed RHV 10SR-ed RHV 12SR-ed RHV 14SR-ed RHV 16SR-ed RHV 20SR-ed RHV 25SR-ed RHV 30SR-ed RHV 38SR-ed
Tube PresOD sure6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38 N.P. 250 N.P. 160 N.P. 100
S117 19 22 27 27 36 41 50 60 65 19 19 22 24 27 32 41 46 60 65
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
S317 19 24 30 32 36 46 55 60 70 19 19 24 27 32 36 46 50 60 70
i8 12 12 12 14 14 16 18 20 22 12 12 12 12 14 14 16 18 20 22
BSP L1 Thread G" " " " " " " 1" 1 " 1 " " " " " " " " 1" 1 " 1 " 42.5 44.5 53 57 60.5 66 71 79.5 90.5 91 46 46 54 57 62 66 73.5 78.5 90.5 100
L228 30 38.5 42.5 45.5 50 55 63 69 69.5 31.5 31.5 38 41 44.5 48 52 54.5 64 69.5
L Light
S Heavy
N.P. 400
N.P. 250
Sr. No Description1 2 3 4 5 6 7 8 9 10
Material C.S. Brass S.S.
Body (Male) C.S. Brass S.S. Body (Female) C.S. Brass S.S. Poppet C.S. Brass S.S. Seal Buna 'N' Buna 'N' Buna 'N' Retainer C.S. Brass S.S. Spring C.S. C.S. S.S. Retainer C.S. Brass S.S. Nut C.S. Brass S.S. Ferrule C.S. Brass S.S. O Ring Buna 'N' Buna 'N' Buna 'N'
NB : 1) Cracking Pressure Standard 0.5 to 1.5 Kg/cm 2) On request upto 6 Kg/cm 3) Kindly mention material of the body
9
NON RETURN VALVE (TUBE END) SERIES - RHZ
Series
Part No.RHZ 6LR-ed RHZ 8LR-ed RHZ 10LR-ed RHZ 12LR-ed RHZ 15LR-ed RHZ 18LR-ed RHZ 22LR-ed RHZ 28LR-ed RHZ 35LR-ed RHZ 42LR-ed RHZ 6SR-ed RHZ 8SR-ed RHZ 10SR-ed RHZ 12SR-ed RHZ 14SR-ed RHZ 16SR-ed RHZ 20SR-ed RHZ 25SR-ed RHZ 30SR-ed RHZ 38SR-ed
Tube PresS1 OD sure6 8 10 12 15 18 22 28 35 42 6 8 10 12 14 16 20 25 30 38 N.P. 250 N.P. 160 N.P. 100 17 19 22 27 27 36 41 50 60 65 19 19 22 24 27 32 41 46 60 65
S214 17 19 22 27 32 36 41 50 60 17 19 22 24 27 30 36 46 50 60
S317 19 24 30 32 36 46 55 60 70 19 19 24 27 32 36 46 50 60 70
i8 12 12 12 14 14 16 18 20 22 12 12 12 12 14 14 16 18 20 22
BSP Thread G" " " " " " " 1" 1 " 1 " " " " " " " " 1" 1 " 1 "
L141 43 53 55 57.5 64 72 80.5 19.5 93 46 46 54 57 61 64 71.5 78.5 90.5 102
L226.5 28.5 38.5 40.5 42.5 48 56 64 70 70.5 31.5 31.5 38 41 43.5 46 50.0 54.5 64 71.5
L Light
S Heavy
N.P. 400
N.P. 250
Sr. No1 2 3 4 5 6 7 8 9 10
DescriptionBody (Male) Body (Female) Poppet Seal Retainer Spring Retainer Nut Ferrule O Ring
Material C.S. Brass S.S.C.S. Brass S.S. C.S. Brass S.S. C.S. Brass S.S. Buna 'N' Buna 'N' Buna 'N' C.S. Brass S.S. NB : 1) Cracking Pressure Standard 0.5 to C.S. C.S. S.S. 1.5 Kg/cm C.S. Brass S.S. 2) On request upto 6 Kg/cm C.S. Brass S.S. 3) Kindly mention material of the body C.S. Brass S.S. Buna 'N' Buna 'N' Buna 'N'
10
SQUARE BODY HIGH PRESSURE BALL VALVE - HBV
Size" " " " 1" 1 " 2"
Part No.4 - HBV 6 - HBV 8 - HBV 12 - HBV 16 - HBV 24 - HBV 32 - HBV
Test Pressure (Bar)700 500 500 500 325 275 200
A51 70 84 95 111 125 140
B60 65 130 150 160 195 195
C40 50 50 75 80 95 105
D6 10 12 20 25 40 50
SW9 9 9 14 14 16 16
Sr. No1 2 3 4 5 6 7 8 9 10 11 12 13
DescriptionBody Adaptor Ball Stem O Ring S. Washer B. Washer P.Washer Stopper Pin Cam Plate Washer Bolt Handle
C.S.C.S. C.S.
Material S.S.S.S S.S S.S. 304/316 S.S. 304 Viton PTFE PTFE/POM/MOS PTFE S.S. 304 M.S. Spring Steel C.S. C.S. Coated
BrassBrass Brass
Qty1 2 1 1 1 1 2 2 1 1 1 1 1
11
SQUARE BODY MEDIUM PRESSURE BALL VALVE MBV
Size" " " " " 1"
Part No.2 - MBV 4 - MBV 6 - MBV 8 - MBV 12 - MBV 16 - MBV
Test Pressure (Bar)300 200 200 150 100 70
A41 51 52 63 80 90
B40 53 63 102 135 142
C30 40 50 55 72 80
D3.2 6.4 9.6 12.7 19 25.4
Sr. No1 2 3 4 5 6 7 8 9 10 11 12
DescriptionBody Adaptor Ball Stem G Nut S. Washer B. Washer P.Washer Stopper Pin Cam Plate Nut Handle
Material C.S.C.S. C.S.
S.S.S.S S.S S.S. 304/316 S.S. 304/316 S.S. 304/316 PTFE PTFE/GFT PTFE S.S. 304 M.S. M.S. C.S. Coated
BrassBrass Brass
Qty1 1 1 1 1 2 2 1 1 1 1 1
12
FLANGE BALL VALVE - FBV
Size" " 1" 1 " 1 " 2" 2 " 3" 4"
Part No.8 - FBV 12 -FBV 16 -FBV 20 - FBV 24 -FBV 32 - FBV 40 - FBV 48 - FBV 64 -FBV
A108 118 127 140 165 178 190 203 229
B145 157 165 175 225 235 275 275 400
C69 78 87 92 114 124 150 156 185
D12.7 19 25.4 32 38 50.8 63.5 76.2 102
F11.2 13 15.6 16.5 17.5 19 22.2 23.8 23.8
PCD60.3 69.9 79.4 88.9 98.4 120.6 139.7 152.4 190.5
Sr. No1 2 3 4 5 6 7 8 9 10 11 12
DescriptionBody Adaptor Ball Stem G Nut S. Washer B. Washer P.Washer Stopper Pin Cam Plate Nut-Stud Handle
Material C.S.C.S. C.S.
S.S. 304S.S. 304 S.S. 304 S.S. 304/316 S.S. 304/316 S.S. 304/316 PTFE/GFT PTFE/GRAFOIL PTFE/GRAFOIL S.S. 304 M.S. C.S/S.S High Tensile C.S. Coated
S.S. 316S.S. 316 S.S. 316
Qty1 2 1 1 1 2 2 2 1 1 9+4 1
13
3 - WAY BALL VALVE - 3BV
Size" " " 1" 1 " 2"
Part No.6 - 3BV 8 -3BV 12 - 3BV 16 - 3BV 24 - 3BV 32 - 3BV
Test Pressure (Bar)150 100 70 70 50 30
A65 72 105 112 175 225
B115 138 175 200 285 315
C48 55 80 85 108 120
D9 9 19 25 32 40
E52 55 83 92 148 160
Sr. No1 2 3 4 5 6 7 8 9 10 11 12
DescriptionBody Adaptor Ball Stem G Nut S. Washer B. Washer P.Washer Stopper Pin Cam Plate Nut-Stud Handle
Material C.S.C.S. C.S.
S.S. 304S.S. 304 S.S. 304 S.S. 304/316 S.S. 304/316 S.S. 304/316 PTFE PTFE/GTV PTFE S.S. 304 M.S. M.S. C.S. Coated
BrassBrass Brass
Qty1 3 1 1 1 2 2 1 1 1 1 1
14
QUICK RELEASE COUPLING (QRC)
FEATURES
1
QUICK RELEASE COUPLING TYPE - V
Dimensions in mm Size " " " " " 1" 1 " Part No. QRC - V1 QRC - V2 QRC - V3 QRC - V4 QRC - V5 QRC - V6 QRC - V7 A D "BSP "BSP "BSP "BSP "BSP 1"BSP 1 "BSP 19 24 24 34 40 42 49 F 16 21 24 28 35 50 50 F1 14 19 22 28 32 40 50 L1 41 53 55 58 83 84 89 L2 27 33 35 42 45 50 54 L 54 70 73 89 107 111 120
W.P. PSI 500 500 500 500 500 500 500
NB :- TYPE - V COUPLING IS WITH SELF SEALING VALVE AT COUPLER END AND THROUGH ADPTOR
2
QUICK RELEASE COUPLING TYPE - V V
Size " " " " " 1" 1 " 1 " 2" 2 " 3"
Part No. QRC - V V1 QRC - V V2 QRC - V V3 QRC - V V4 QRC - V V5 QRC - V V6 QRC - V V7 QRC - V V8 QRC - V V9
A "BSP "BSP "BSP "BSP "BSP 1"BSP 1 "BSP 1 "BSP 2"BSP
Dimensions in mm D 23 32 38 44 48 58 72 89 105 118 127 L1 44 58 66 71 77 85 94 113 127 132 140 L2 33 40 45 50 55 63 65 80 88 94 103 L 58 72 80 90 98 112 120 144 152 158 180
T.P. PSI 6000 6000 6000 5000 4500 4000 3000 3000 2500 1500 1500
W.P. PSI 4000 4000 4000 3500 3000 2500 2000 2000 1500 1000 1000
QRC - V V10 2 "BSP QRC - V V11 3"BSP
NB :- TYPE - V V COUPLING IS WITH SELF SEALING VALVE AT BOTH COUPLER AND ADPTOR END
3
QUICK RELEASE COUPLING TYPE - T
Dimensions in mm Size " " " " " 1" 1 " 1 " 2" Part No. QRC - T1 QRC - T2 QRC - T3 QRC - T4 QRC - T5 QRC - T6 QRC - T7 QRC - T8 QRC - T9 A D "BSP "BSP "BSP "BSP "BSP 1"BSP 1 "BSP 1 "BSP 2"BSP 18 28 32 35 42 50 60 70 88 F 14 22 25 28 40 45 55 57 72 F1 14 19 22 28 32 40 50 57 69 L1 31 39 41 44 54 57 62 66 77 L2 32 40 42 47 52 60 65 68 78 L 47 57 60 66 78 85 93 97 110
W.P. PSI 500 500 500 500 500 500 500 500 500
NB :- TYPE - T COUPLING (WITHOUT VALVE) THROUGH TYPE
4
Hose Internal Diameter
MetricDKO - L METRIC FEMALE 90 ELBOW DKS METRIC FEMALE DKS METRIC FEMALE 45 ELBOW DKS METRIC FEMALE 90 ELBOW DKO - S METRIC FEMALE DKO - S METRIC FEMALE 45 ELBOW DKO - S METRIC FEMALE 90 ELBOW
INCH MM DASH
3/16" 4.8 -3 -
1/4" 6.4 -4
5/16" 7.9 -5
3/8" 9.5 -6
1/2" 12.7 -8
5/8" 15.9 -10
3/4" 19.0 -12
1" 25.4 -16 M36 X 2 M36 X 2
1 1/4" 31.8 -20 M45 X 2 M52 X 2 M52 X 2 M52 X 2 M52 X 2 M52 X 2 M52 X 2 -
1 1/2" 38.1 -24 M52 X 2 -
2" 50.8 -32 -
M14 X 1.5 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M36 X 2 M30 X 2 M36 X 2 M30 X 2 M36 X 2 M36 X 2 M36 X 2 M36 X 2 -
F I T T I N G T H R E A D S I Z E
-
M16 X 1.5 M20 X 1.5 M20 X 1.5 M24 X 1.5 M30 X 2 M18 X 1.5 M22 X 1.5 -
M42 X 2 M42 X 2 M42 X 2 M42 X 2 M42 X 2 M42 X 2 -
M16 X 1.5 M20 X 1.5 M20 X 1.5 M24 X 1.5 M30 X 2 M18 X 1.5 M22 X 1.5 -
M16 X 1.5 M20 X 1.5 M20 X 1.5 M24 X 1.5 M30 X 2 M18 X 1.5 M22 X 1.5 -
M16 X 1.5 M20 X 1.5 M20 X 1.5 M24 X 1.5 M30 X 2 M18 X 1.5 M22 X 1.5 -
M16 X 1.5 M20 X 1.5 M20 X 1.5 M24 X 1.5 M30 X 2 M18 X 1.5 M22 X 1.5 -
M16 X 1.5 M20 X 1.5 M20 X 1.5 M24 X 1.5 M30 X 2 M18 X 1.5 M22 X 1.5 -
1
Hose Internal Diameter
MetricKOMATSU METRIC FEMALE INVERTED CONE METRIC BANJO
INCH MM DASH
3/16" 4.8 -3 -
1/4" 6.4 -4 M14 X 1.5 12.1 9.8 13.3 16.8 6 8 6 8 8 10 12 8 10 12
5/16" 7.9 -5 12.1 14 10 10 12 12 -
3/8" 9.5 -6
1/2" 12.7 -8
5/8" 15.9 -10
3/4" 19.0 -12
1" 25.4 -16
1 1/4" 31.8 -20
1 1/2" 38.1 -24
2" 50.8 -32 -
M18 X 1.5 M22 X 1.5 M24 X 1.5 M30 X 1.5 M33 X 1.5 M36 X 1.5 M42 X 1.5 14 16.1 16.8 10 12 15 10 12 14 14 18 21 12 15 18 15 18 14 16 14 16 18 18 22 18 22 20 20 26.5 22 22 20 25 20 25 28 28 25 30 25 30 35 38 42 -
BSP - BANJO
F I T T I N G T H R E A D S I Z E
6 8 8 -
STAND PIPE METEIC (LT) STRAIGHT DIN - 2353 STAND PIPE METEIC (LT) 90 ELBOW DIN - 2353 STAND PIPE METEIC (HT) STRAIGHT DIN - 2353 STAND PIPE METEIC (HT) 90 ELBOW DIN - 2353
2
Hose Internal Diameter
MetricCEL - MALE (LIGHT)
INCH MM DASH
3/16" 4.8 -3 -
1/4" 5/16" 3/8" 1/2" 5/8" 3/4" 6.4 7.9 9.5 12.7 15.9 19.0 -4 -5 -6 -8 -10 -12 M16 X 1.5 M12 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M16 X 1.5 M18 X 1.5 M14 X 1.5 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M36 X 2
1" 25.4 -16 M36 X 2 M42 X 2 M36 X 2 M36 X 2 -
1 1/4" 31.8 -20 M45 X 2 M52 X 2 M45 X 2 M45 X 2 -
1 1/2" 38.1 -24 M52 X 2 M52 X 2 M52 X 2 -
2" 50.8 -32 -
CEL - MALE (HEAVY)
DKL METRIC FEMALE DKL METRIC FEMALE 45 ELBOW DKL METRIC FEMALE 90 ELBOW DKO - L METRIC FEMALE DKO - L METRIC FEMALE 45 ELBOW
F I T T I N G T H R E A D S I Z E
-
M16 X 1.5 M20 X 1.5 M20 X 1.5 M24 X 1.5 M30 X 2 M18 X 1.5 M22 X 1.5 -
M14 X 1.5 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M16 X 1.5 M18 X 1.5 M22 X 1.5 -
M14 X 1.5 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M16 X 1.5 M18 X 1.5 M22 X 1.5 -
M14 X 1.5 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M16 X 1.5 M18 X 1.5 M22 X 1.5 -
M14 X 1.5 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M16 X 1.5 M18 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M36 X 2
M14 X 1.5 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M30 X 2 M16 X 1.5 M18 X 1.5 M22 X 1.5 M26 X 1.5 M36 X 2
3
Hose Internal Diameter
BSPBSP MALE PARALLEL 60 CONE SEAT
INCH MM DASH
3/16" 4.8 -3 1/8" - 28 1/8" - 28 1/8" - 28 -
1/4" 6.4 -4 1/4" - 19 3/8" - 19 1/4" - 19 3/8" - 19 1/4" - 19 3/8" - 19 1/4" - 19 3/8" - 19 1/4" - 19
5/16" 7.9 -5 3/8" - 19 3/8" - 19 3/8" - 19 3/8" - 19 3/8" - 19
3/8" 9.5 -6 3/8" - 19 1/2" - 14 3/8" - 19 1/2" - 14 3/8" - 19 1/2" - 14 3/8" - 19 1/2" - 14 3/8" - 19
1/2" 12.7 -8 1/2" - 14 5/8" - 14 1/2" - 14 1/2" - 14 5/8" - 14 1/2" - 14 1/2" - 14
5/8" 15.9 -10 5/8" - 14 3/4" - 14 3/4" - 14 5/8" - 14 3/4" - 14 5/8" - 14 3/4" - 14 5/8" - 14
3/4" 19.0 -12 3/4" - 14 1" - 11 3/4" - 14 3/4" - 14 1" - 11 3/4" - 14 3/4" - 14
1" 25.4 -16 1" - 11 1 1/4" - 11 1" - 11 1" - 11 1 1/4" - 11 1" - 11 1" - 11
1 1/4" 31.8 -20
1 1/2" 38.1 -24
2" 50.8 -32
1 1/4" - 11 1 1/2" - 11 2" - 11 -
BSP MALE TAPER
BSP FEMALE
F I T T I N G T H R E A D S I
1 1/4" - 11 1 1/2" - 11 2" - 11 -
1 1/4" - 11 1 1/2" - 11 2" - 11 -
1 1/4" - 11 1 1/2" - 11 2" - 11 -
BSP FEMALE 45 ELBOW
1 1/4" - 11 1 1/2" - 11 2" - 11
BSP FEMALE 90 ELBOW
-
3/8" - 19
-
1/2" - 14
-
3/4" - 14
-
-
-
-
-
BSP FEMALE INVERTED CONE (J.I.S)
Z E
-
1/4" - 19 -
-
3/8" - 19 -
1/2" - 14 -
5/8" - 14 -
3/4" - 14 -
1" - 11 -
-
-
-
4
Hose Internal Diameter
BSPBSP FEMALE INVERTED CONE (J.I.S) 45 ELBOW
INCH MM DASH
3/16" 4.8 -3 -
1/4" 6.4 -4 1/4" - 19
5/16" 7.9 -5 -
3/8" 9.5 -6 3/8" - 19
1/2" 12.7 -8 1/2" - 14
5/8" 15.9 -10 5/8" - 14
3/4" 19.0 -12 3/4" - 14
1" 25.4 -16 1" - 11
1 1/4" 31.8 -20 -
1 1/2" 38.1 -24 -
2" 50.8 -32 -
F I T T
-
-
-
-
-
-
-
-
-
-
-
BSP FEMALE INVERTED CONE (J.I.S) 90 ELBOW
I N G T H R E
-
1/4" - 19
-
3/8" - 19
1/2" - 14
5/8" - 14
3/4" - 14
1" - 11
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1/4" - 19
-
3/8" - 19
1/2" - 14
5/8" - 14
3/4" - 14
1" - 11
-
-
-
BSP FEMALE O RING TYPE
-
-
-
-
-
-
-
-
-
-
-
BSP FEMALE O RING TYPE 45 ELBOW
A D S
1/4" - 19
-
3/8" - 19
1/2" - 14
-
3/4" - 14
1" - 11
-
-
-
-
-
-
-
-
-
-
-
-
-
BSP FEMALE O RING TYPE 90 ELBOW
I Z E
-
1/4" - 19
-
3/8" - 19
1/2" - 14
-
3/4" - 14
1" - 11
1 1/4" - 11 1 1/2" - 11 2" - 11
-
-
-
-
-
-
-
-
-
-
-
5
Hose Internal Diameter
FLANGESSAE 3000PSI (CODE - 61)
INCH MM DASH
1/2" 12.7 -8 30.18 (-8) 38.1 (-12) 30.18 (-8) 38.1 (-12) 30.18 (-8) 38.1 (-12) 31.75 (-8) 31.75 (-8) 31.75 (-8) -
5/8" 15.9 -10 -
3/4" 19.0 -12 38.1 (-12) 44.45 (-16) 38.1 (-12) 44.45 (-16) 38.1 (-12) 44.45 (-16) 41.28 (-12) 31.75 (-8) 41.28 (-12) 31.75 (-8) 41.28 (-12) 31.75 (-8)
1" 25.4 -16 44.45 (-16) 50.8 (-20) 44.45 (-16) 50.8 (-20) 44.45 (-16) 50.8 (-20) 47.63 (-16) 41.28 (-12) 47.63 (-16) 41.28 (-12) 47.63 (-16) 41.28 (-12)
1 1/4" 31.8 -20 50.8 (-20) 60.33 (-24) 50.8 (-20) 60.33 (-24) 50.8 (-20) 60.33 (-24) 53.98 (-20) 63.5 (-24) 53.98 (-20) 63.5 (-24) 53.98 (-20) 63.5 (-24)
1 1/2" 38.1 -24 60.33 (-24) 60.33 (-24) 60.33 (-24) 63.5 (-24) 63.5 (-24) 63.5 (-24) -
2" 50.8 -32 71.42 (-32) 71.42 (-32) 71.42 (-32) 79.38 (-32) 79.38 (-32) 79.38 (-32) -
SAE 3000PSI (CODE - 61) 45 ELBOW
SAE 3000PSI (CODE - 61) 90 ELBOW
F I T T I N G T H R E A D S I Z E
SAE 6000PSI (CODE - 62)
SAE 6000PSI (CODE - 62) 45 ELBOW
SAE 6000PSI (CODE - 62) 90 ELBOW
6
Hose Internal Diameter
FLANGESKOMATSU STANDARD PRESSURE
INCH MM DASH
1/2" 12.7 -8 30.2 (-8) 30.2 (-8) 30.2 (-8) -
5/8" 15.9 -10 34.2 (-10) 34.2 (-10) 34.2 (-10) -
3/4" 19.0 -12 38.1 (-12) 38.1 (-12) 38.1 (-12) -
1" 25.4 -16 44.5 (-16) 44.5 (-16) 44.5 (-16) -
1 1/4" 31.8 -20 50.8 (-20) 50.8 (-20) 50.8 (-20) 54 (-20) 54 (-20) 54 (-20) -
1 1/2" 38.1 -24 60.3 (-24) 60.3 (-24) 60.3 (-24) 63.5 (-24) 63.5 (-24) 63.5 (-24) -
2" 50.8 -32 71.4 (-32) 71.4 (-32) 71.4 (-32) 79.4 (-32) 79.4 (-32) 79.4 (-32) -
KOMATSU STANDARD PRESSURE 45 ELBOW
KOMATSU STANDARD PRESSURE 90 ELBOW
F I T T I N G T H R E A D S I Z E
KOMATSU HIGH PRESSURE
KOMATSU HIGH PRESSURE 45 ELBOW
KOMATSU HIGH PRESSURE 90 ELBOW
7
ORFS & JIC/ SAEORFS MALE
Hose Internal DiameterINCH MM DAS H 3/16" 4.8 -3 1/4" 6.4 -4 5/16" 7.9 -5 3/8" 9.5 -6 11/16" 16 11/16" 16 13/16" 16 11/16" 16 13/16 - 16 11/16" 16 13/16" 16 1/2" 12.7 -8 13/16" 16 13/16" 16 1" - 14 13/16" 16 1" - 14 13/16" 16 1" - 14 5/8" 15.9 -10 3/4" 19.0 -12 1" 25.4 -16 1 1/4" 31.8 -20 1 1/2" 38.1 -24 2" 50.8 -32 -
F I T T I N G
1 3/16" - 1 7/16" 12 12 -
-
-
11/16" 16 11/16" 16 11/16" 16 -
-
-
-
-
-
9/16" - 18 11/16" 16 9/16" - 18 11/16" 16 9/16" - 18 11/16" 16
1" - 14
1 3/16" - 1 7/16" - 1 11/16" 12 12 12 1 7/16" 12 -
-
-
ORFS FEMALE
-
-
-
-
ORFS FEMALE 45 ELBOW
T H R E
-
1" - 14
1 3/16" - 1 7/16" - 1 11/16" 12 12 12 1 7/16 12 -
-
-
-
-
-
-
ORFS FEMALE 90 ELBOW
A D S I
-
1" - 14
1 3/16" - 1 7/16" - 1 11/16" 12 12 12 1 7/16" 12 -
-
-
-
-
-
-
-
1/2" - 20 9/16" - 18 3/4" - 16
7/8" - 14
1 1/16" - 1 1/16" - 1 5/16" 1 5/8" - 12 12 12 12 7/8" - 14 1 5/16" 12 -
1 7/8" - 12
2 1/2" - 12
JIC MALE
Z E
-
7/16" - 20
-
9/16" - 18 3/4" - 16
-
-
8
ORFS & JIC/ INCH MM SAE DASHJIC FEMALE
Hose Internal Diameter3/16" 4.8 -3 1/4" 6.4 -4 5/16" 7.9 -5 3/8" 9.5 -6 3/4" - 16 1/2" 12.7 -8 7/8" - 14 5/8" 15.9 -10 1 1/16" 12 7/8" - 14 1 1/16" 12 7/8" - 14 3/4" 19.0 -12 1 1/16" 12 1 5/16" 12 1 1/16" 12 1 5/16" 12 1 1/16" 12 1" 25.4 -16 1 1/4" 31.8 -20 1 1/2" 38.1 -24 2" 50.8 -32 2 1/2" - 12
F I T T
1/2" - 20 9/16" - 18
1 5/16" 1 5/8" - 12 1 7/8" - 12 12 -
-
7/16" - 20
-
9/16" - 18
3/4" - 16
-
JIC FEMALE 45 ELBOW
I N G
-
1/2" - 20 9/16" - 18
3/4" - 16
7/8" - 14
1 5/16" 1 5/8" - 12 1 7/8" - 12 12 -
2 1/2" - 12
-
7/16" - 20
-
9/16" - 18
3/4" - 16
-
JIC FEMALE 90 ELBOW
T H R E A D S
-
1/2" - 20 9/16" - 18
3/4" - 16
7/8" - 14
1 1/16" 12 7/8" - 14
1 5/16" 1 5/8" - 12 1 7/8" - 12 12 -
2 1/2" - 12
-
7/16" - 20
-
9/16" - 18
3/4" - 16
-
1/8" - 27
1/4" - 18
3/8" - 18
3/8" - 18
1/2" - 14
3/4" - 14
3/4" - 14
1" - 11
1 1/4" 11 1 1/2" - 11
2 1/2"- 11
NTP MALE
-
3/8" - 18
-
1/2" - 14
-
-
-
-
-
-
-
SAE FEMALE
I Z E
-
7/16" - 20 5/8" - 18
5/8" - 18
3/4" - 16
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9
