Part Numbers
Revised: 07/2016 Drinking Water Systems – Parts Pages Section 7
Page 1
Kinetico Drinking Water Systems
Model 7000/7500 Components
Section 7 Drinking Water Systems – Parts Pages Revised: 07/2016
Page 2
Dwg. No. Description Part No.
1 Screws (3 required) 1010
2 Ball Valve, Inlet 15792
3 MAC Head 12870A
4 Bracket 9328
5A Elbow, Male ¼” Tube x ⅜” Stem, V/L 15791
5B Elbow, Male ¼” Tube x ⅜” Stem, GAC 15793
6A Cartridge, MAC, V/L 9308A
6B Cartridge, MAC, GAC 9306B
7A Drinking Water Filter, Model 7000 with install kit 4049A
7B Drinking Water Filter, Model 7500 with install kit 4050A
8 K5 Flow Supressor* 13477
*For the use in Mac 7500 only
1
4
5A
5B
6B
7A
7B
3
2
6A
8
Model 7000/7500 Components
Revised: 07/2016 Drinking Water Systems – Parts Pages Section 7
Page 3
Dwg. No. Description Part No.
1 Mounting Screws (2 required) 3321A
2A Elbow, Male, ¼” Tube x ¼” NPT, V/L 15791
2B Elbow, Male, ¼” Tube x ¼” NPT, GAC 15793
3 Union Connector, ¼” T x ¼” T 9847A
4 Tubing, ¼” x 10’ 8554A
5 Ball Valve 9460
6 Tee, ⅜” x ¼” 9207A
7A Assembly Kit, V/L 14938A
7B Assembly Kit, GAC 14937A
8 Faucet, non-air gap 11450B
9 K5 Flow Supressor* 13477
*For the use in Mac 7500 only
1
3
4
7A 2B
5
6
2A
7B
8
Plus Deluxe Module Assembly
Section 7 Drinking Water Systems – Parts Pages Revised: 07/2016
Page 4
Dwg. No. Description Part No.
1 Sump with Plug, RO - Siliconed 12971
2 Module Subassembly (does not include tubing collets) 10504
3 Membrane Assembly 10501
4 Module Assembly 10500
5 O-ring (Top) 9063
6 O-ring (Middle) 5021
7 O-ring (Bottom) 5020
8 O-ring (Membrane) 2648
Complete Assembly
1 2 3 4
7
6
5 8
Plus Deluxe Bracket Assembly
Revised: 07/2016 Drinking Water Systems – Parts Pages Section 7
Page 5
Dwg. No. Description Part No.
1 Cartridge, Prefilter - Sediment 9309A
1 Cartridge, Prefilter - Carbon/Sediment, High Capacity 9461A
2 Prefilter Head 9313C
3 Elbow, Male ¼" Tube x ¼" NPT 8551
4 Bracket 9326
5 Manifold Clip 9301A
6 Module Assembly - TF 10500
7 Cap Screws 1010
8 MAC Postfilter Head 9382
9 Elbow, Male ⅜” Tube x ¼” NPT (GX) 8552
9 Elbow, ⅜” Tube x ¼” NPT with Flow Control (VX) 9373
10 Cartridge, MAC Postfilter - VOC (VX) 9307A
10 Cartridge, MAC Postfilter - GAC (GX) 9306B
11 Manifold Assembly 9335A
12 Bracket Cover - VX 9358A
12 Bracket Cover - GX 9359A
AquaKinetic® A200 Bracket Assembly
Section 7 Drinking Water Systems – Parts Pages Revised: 07/2016
Page 6
Drawing No. Description Part No.
1 Cartridge, Prefilter - Sediment 9309A
1 Cartridge, Prefilter, Carbon/Sediment, High Capacity 9461A
2 Prefilter Head 9313C
3 Inlet Elbow, Male ¼” Tube x ¼” NPT 8551A
4A Bracket 9441
4B Bracket Assembly 9442
5 Cartridge, Membrane 9428A
6 Cap screws 1010
7 Postfilter head 9426C
8 Elbow, Male ⅜” Tube x ¼” NPT 8552A
9 Cartridge, MAC GAC Postfilter 9306B
10 Bracket Cover 9443B
11 Module Head Assembly 9440
Not Shown Flow Restrictor, Capillary, A200 10803A
Not Shown Drain Elbow 8551A
Not Shown Economy Faucet, non air gap 11450B
Not Shown Economy Faucet, air gap 11451B
1
2
3
9
10
8
7
6
5
4
4B
11
Plus and A200 Faucets
Revised: 07/2016 Drinking Water Systems – Parts Pages Section 7
Page 7
Description Plus Deluxe and
Purefecta Part No. A200 Part
No. Tap
Escutcheon
Non-Air Gap Taps:
Tap, Decorative, Classic Chrome 12725 NA 11621
Tap, Decorative, Satin Nickel 12770 NA 11623
Tap, Decorative, Arctic White 12765 NA 11627
Tap, Decorative, Light Biscuit 12768 NA 11626
Tap, Decorative, Black Licorice 12766 NA 11628
Tap, Decorative, Oil Rubbed Bronze 14683 NA 14684
Tap, Decorative, Polished Brass 12769 NA 11625
Tap, Decorative, Brilliant Nickel 12767 NA 11622
Tap, Decorative, Brushed Stainless 13289 NA NA
Tap, Economy Chrome NA 11450B NA
Air Gap Taps:
Tap, Economy Chrome NA 11451B NA
Kit, Air Gap Decorator Tap 12961A NA NA
Tap Handle, A200 Only NA 9380 NA
Connector, ¼ x ⅜, A200 Only NA 8561A NA
Cartridge, Decorator Faucet 12072 NA NA
Part No. 12939
3 Gallon QuickFlo®
Section 7 Drinking Water Systems – Parts Pages Revised: 07/2016
Page 8
Plus Deluxe and A200 Units
Part No. Description Color Code
9309A Cartridge, Sediment Prefilter (Plus Deluxe and A200 Models) Yellow Decal
9307A Cartridge, MAC Postfilter – Plus Deluxe VX (Replacement only),
Plus Deluxe Models ONLY Blue Decal
9306B Cartridge, MAC Postfilter Plus Deluxe GX (Plus and A200 Models) Orange Decal
9461A High Capacity Carbon/Sediment (Plus Deluxe and A200 Models) Purple Decal
9305A Insert
Storage Tanks
Revised: 07/2016 Drinking Water Systems – Parts Pages Section 7
Page 9
Drawing No. Description Plus and A200
Models
1 Ball Valve, ⅜", Storage Tank 11378
2 Adapter, Stem Tube 9396
3 Bushing, Red ¾” x ⅜" NPT 7542
4 Coupling, ¾” x PVC-thd. 7969
5 Ball Valve Kit 9395
6 Storage Tank, 10 Gallon 12968
7 Storage Tank Assembly, 10 Gallon - RO 9375
8 Ball Valve, ¼ FNPT x ⅜T 12583A
9 Storage Tank, 3 Gallon, Black 9344B
2
4
3
6
5
7
9
1
8
3 Gallon QuickFlo®
Section 7 Drinking Water Systems – Parts Pages Revised: 07/2016
Page 10
Drawing No. Description Part No.
1 Control Valve Assembly 10248C
2 Foot Storage Tank 9487
3 Retainer Storage Tank (not shown) 7964
4 Bladder 9408A
5 Tank Complete – 3 gallon 9496
6 Tank only – 3 gallon QuickFlo 11716
1
4
5
2
3
6
Reverse Osmosis Accessories
Revised: 07/2016 Drinking Water Systems – Parts Pages Section 7
Page 11
Booster Pump This Kinetico accessory is designed to produce a higher volume and better quality of water than is possible under low pressure operating conditions. A booster pump is recommended whenever high TDS or low pressure conditions exist. If the volume of water produced by the Kinetico Drinking Water System with the available water pressure is not satisfactory to the customer, a booster pump can be added.
The booster pump raises the feed pressure entering the R.O. module to approximately 95 psig. The increased pressure increases the volume and the quality of permeate water produced by the RO module.
The Kinetico RO Booster Pump consists of an electric diaphragm pump, voltage transformer and a pressure switch, which turns the pump on via a signal from the Kinetico Drinking Water System. All these components are packaged in an attractive enclosure with a removable cover.
The booster pump measures 12" long by 7" wide by 5" high, making it easy to install beneath a kitchen sink or any desirable location. The pump comes with a 5 foot electrical cord.
Operation When the Kinetico Drinking Water System senses the tank needs to be filled, the main spool valve in the R.O. module (or the shutoff valve on A200 units) opens. Feed water enters the inlet port, pressurizing the membrane and the bottom of the module.
The booster pump pressure switch is connected to a port in the bottom of the RO module via an elbow and ¼" O.D. tubing included in the optional installation kit. The pressure switch contacts close when the water pressure reaches approximately 10 psig. This starts the booster pump, which produces regulated 95 psig water pressure at the RO module inlet port.
Permeate water is now produced by the membrane and fills the storage tank. When the storage tank water pressure reaches approximately 2/3 of line pressure (in this case 62 of 95 psig) the Kinetico Drinking Water System shuts down, preventing any more feed water from entering the membrane. On Plus units, the membrane is then flushed with permeate water.
Then the bottom of the sump begins to depressurize. When the pressure falls to less than 10 psig, the pressure switch contacts open, shutting off the pump. The pump will remain off until enough water is consumed to lower the pressure in the storage tank to the turn on point of the R.O. system. Feed water now enters the inlet port, applying pressure to the membrane and the bottom of the module and starting the cycle over again.
Notes and Cautions - Do not run pump dry for extended periods.
The use of a Ground Fault Interrupter (GFI) is recommended and may be required locally. Consult and follow state and local codes for your specific area before starting installation.
Always unplug pump before servicing.
Reverse Osmosis Accessories
Section 7 Drinking Water Systems – Parts Pages Revised: 07/2016
Page 12
Kinetico Drinking Water System Plus
1. Water inlet from cold water supply (Plus units)
2. Water outlet discharge to RO prefilter inlet (Plus)
3. Signal line from bottom of RO module
4. Power cord
Specifications
Size: ........................................................12.0" x 7.0" x 5.0"
Maximum TDS: .......................................TF membrane - 4000 ppm
Maximum Feed Water Temperature: ....100°F
Maximum Feed Water Pressure: ...........60 psig
Minimum Feed Water Pressure: ............15 psig
Power Requirements
Voltage: ...........115 VAC
Cycle: ..............60 Hz
Tools and Supplies Required
¼" Allen Wrench
Teflon Thread Tape
1
2
4
3
Reverse Osmosis Accessories
Revised: 07/2016 Drinking Water Systems – Parts Pages Section 7
Page 13
Shurflo Booster Pump (part no. 9069A) Installation Kit (part no. 7281)
1 - Length of ¼" O.D. Tubing (part no. 8554A)
1 - Male Elbow, ¼" NPT X ¼" O.D. Tube (part no. 8551)
1 - Tee, Union, ¼" Tube (part no. 8748)
1 - Elbow, ¼” Tube X ¼” Stem (part no. 8958)
Wrenches and Drain Saddle
Dwg. No. Description Part No.
1 Wrench, Module 3960
2 Wrench, Sump 5223
3 Drain Saddle 4806
2
3
Top View Bottom View
1
Reverse Osmosis Accessories
Section 7 Drinking Water Systems – Parts Pages Revised: 07/2016
Page 14
RO Fittings
Part No. 8748 Tee, ¼" x ¼” x ¼” w/ metal gripper
Parker True Seal fittings
Part No. 10803A Flow Restrictor, Capillary, A200
Part No. 8553 Tee, ⅜" T x ¼" T x ¼" NPT
Parker True Seal fittings
Part No. 9410 Manifold Adapter Pin
Reverse Osmosis Accessories
Revised: 07/2016 Drinking Water Systems – Parts Pages Section 7
Page 15
Part No. 8968 Tee, ⅜" x ⅜" x ⅜"
Parker True Seal fittings
Part No. 8561A Union Connector, ⅜" T x ¼" T
Parker True Seal fittings
Part No. 7761 Swivel Elbow
Part No. 8574 3/8" diameter collet
Parker True Seal fittings
Reverse Osmosis Accessories
Section 7 Drinking Water Systems – Parts Pages Revised: 07/2016
Page 16
Part No. 8575A ⅜" diameter O-ring
Parker True Seal fittings
Part No. 3977 Gauge, low pressure
Checking storage tank air pressure
Part No. 5024 Assembly pressure test
Used to check water pressure throughout R.O. unit
Part No. 8563 1/4" diameter collet
Parker True Seal fittings
Reverse Osmosis Accessories
Revised: 07/2016 Drinking Water Systems – Parts Pages Section 7
Page 17
Part No. 8564A ¼" diameter O-ring
Parker True Seal fittings
Part No. 11439 Fitting,3/8” Adapter Ice Maker
RO Tubing, Tools, and Fittings
Part No. 1890 Tubing, ⅜" diameter x 100'
Polyethylene
Reverse Osmosis Accessories
Section 7 Drinking Water Systems – Parts Pages Revised: 07/2016
Page 18
Part No. 8586 Tool, Tubing Release
Parker True Seal™ fittings
Part No. 8552A Elbow, ¼" NPT x ⅜" tube
Part No. 11378 Valve, Ball Tank ⅜” stem
Part No. 8555 Tubing, ¼" diameter x 100'
Polyethylene
Reverse Osmosis Accessories
Revised: 07/2016 Drinking Water Systems – Parts Pages Section 7
Page 19
Part No. 8587 Tool, Tubing Cutter
Parker True Seal fittings
Part No. 8560 Ball Valve, ¼", Plastic
Part No. 12866 Pressure Switch, Plus Deluxe
Booster Pump
Part No. – 12855B 1/4" Diameter Collet – Black
Parker True Seal Fittings